Here's the big char/misc driver patches for 4.10-rc1. Lots of tiny
changes over lots of "minor" driver subsystems, the largest being some
new FPGA drivers. Other than that, a few other new drivers, but no new
driver subsystems added for this kernel cycle, a nice change.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWFAtwA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykyCgCeJn36u1AsBi7qZ3u/1hwD8k56s2IAnRo6U31r
WW65YcNTK7qYXqNbfgIa
=/t/V
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver patches for 4.10-rc1. Lots of tiny
changes over lots of "minor" driver subsystems, the largest being some
new FPGA drivers. Other than that, a few other new drivers, but no new
driver subsystems added for this kernel cycle, a nice change.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (107 commits)
uio-hv-generic: store physical addresses instead of virtual
Tools: hv: kvp: configurable external scripts path
uio-hv-generic: new userspace i/o driver for VMBus
vmbus: add support for dynamic device id's
hv: change clockevents unbind tactics
hv: acquire vmbus_connection.channel_mutex in vmbus_free_channels()
hyperv: Fix spelling of HV_UNKOWN
mei: bus: enable non-blocking RX
mei: fix the back to back interrupt handling
mei: synchronize irq before initiating a reset.
VME: Remove shutdown entry from vme_driver
auxdisplay: ht16k33: select framebuffer helper modules
MAINTAINERS: add git url for fpga
fpga: Clarify how write_init works streaming modes
fpga zynq: Fix incorrect ISR state on bootup
fpga zynq: Remove priv->dev
fpga zynq: Add missing \n to messages
fpga: Add COMPILE_TEST to all drivers
uio: pruss: add clk_disable()
char/pcmcia: add some error checking in scr24x_read()
...
Since targets are given a virtual target device, it is necessary to
translate all communication between targets and the backend device.
Implement the translation layer for get/set bad block table.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
On target-specific operations pass on nvm_tgt_dev instead of the generic
nvm device.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Target devices do not have access to the device driver operations.
Introduce a helper function that exposes the max. number of physical
sectors supported by the underlying device.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Avoid calling media manager and device-specific operations directly from
rrpc. Create helper functions on lightnvm's core instead.
Signed-off-by: Javier González <javier@cnexlabs.com>
Made it work with null_blk as well.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
In order to naturally support multi-target instances on an Open-Channel
SSD, targets should own the LUNs they get blocks from and manage
provisioning internally. This is done in several steps.
Since targets own the LUNs the are instantiated on top of and manage the
free block list internally, there is no need for a LUN abstraction in
the media manager. LUNs are intrinsically managed as in the physical
layout (ch:0,lun:0, ..., ch:0,lun:n, ch:1,lun:0, ch:1,lun:n, ...,
ch:m,lun:0, ch:m,lun:n) and given to the targets based on the target
creation ioctl. This simplifies LUN management and clears the path for a
partition manager to sit directly underneath LightNVM targets.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
In order to naturally support multi-target instances on an Open-Channel
SSD, targets should own the LUNs they get blocks from and manage
provisioning internally. This is done in several steps.
A part of this transformation is that targets manage their blocks
internally. This patch eliminates the nvm_block abstraction and moves
block management to the target logic. The rrpc target is transformed.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since LUNs are managed internally on targets, the media manager has no
access to the free LUN lists. Thus, debug functions that show LUN
information on the device should not be implemented on the media
manager, but rather on the target in itself.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since LUNs are managed internally on the target, there is no need for
the media manager to implement a get_lun operation.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
In order to naturally support multi-target instances on an Open-Channel
SSD, targets should own the LUNs they get blocks from and manage
provisioning internally. This is done in several steps.
This patch moves the block provisioning inside of the target and removes
the get/put block interface from the media manager.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
LUNs are exclusively owned by targets implementing a block device FTL.
Doing this reservation requires at the moment a 2-way callback gennvm
<-> target. The reason behind this is that LUNs were not assumed to
always be exclusively owned by targets. However, this design decision
goes against I/O determinism QoS (two targets would mix I/O on the same
parallel unit in the device).
This patch makes LUN reservation as part of the target creation on the
media manager. This makes that LUNs are always exclusively owned by the
target instantiated on top of them. LUN stripping and/or sharing should
be implemented on the target itself or the layers on top.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The gen_lun abstraction in the generic media manager was conceived on
the assumption that a single target would instantiated on top of it.
This has complicated target design to implement multi-instances. Remove
this abstraction and move its logic to nvm_lun, which manages physical
lun geometry and operations.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
There is a constant to refer to free blocks. Use it when marking bad
blocks instead of using a constant value
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Before vectored I/Os were supported on rrpc, the physical address was
stored as part of the nvm_rqd request. This variable become obsolete
when the ppa_list was introduced. Cleanup this variable.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Targets are assumed to used the same generic ppa format, where the
address is partitioned on ch:lun:block:pg:pl:sec. Thus, make the
function in charge of transforming the ppa address from a linear format
to the generic one available to all targets.
This function will be needed by the media manager in order to do target
mapping translations when targets are divided on different physical
partitions.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
LightNVM used to be managed and configured through sysfs. Since the
introduction of management ioctls this interface is redundant and
outdated. Get rid of it.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
rrpc cannot handle bios of size > 256kb due to NVMe using a 64 bit
bitmap to signal I/O completion. If a larger bio comes, split it
explicitly.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Bad blocks should be managed by block owners. This would be either
targets for data blocks or sysblk for system blocks.
In order to support this, export two functions: One to mark a block as
an specific type (e.g., bad block) and another to update the bad block
table on the device.
Move bad block management to rrpc.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Device blocks should be marked by the device and considered as bad
blocks by the media manager. Thus, do not make assumptions on which
blocks are going to be used by the device. In doing so we might lose
valid blocks from the free list.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Erases might be subject to host hints. An example is multi-plane
programming to erase blocks in parallel. Enable targets to specify this
hint.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Previously, LBA read and write were not supported in the lightnvm
specification. Now that it supports it, lets use the traditional
NVMe gendisk, and attach the lightnvm sysfs geometry export.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The Kconfig currently controlling compilation of this code is:
drivers/lightnvm/Kconfig:menuconfig NVM
drivers/lightnvm/Kconfig: bool "Open-Channel SSD target support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_misc_driver translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
We replace module.h with moduleparam.h because this file still uses
module params to control behaviour.
Also note that MODULE_ALIAS is a no-op for non-modular code.
Cc: Matias Bjorling <mb@lightnvm.io>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull block layer updates from Jens Axboe:
"This is the main pull request for block layer changes in 4.9.
As mentioned at the last merge window, I've changed things up and now
do just one branch for core block layer changes, and driver changes.
This avoids dependencies between the two branches. Outside of this
main pull request, there are two topical branches coming as well.
This pull request contains:
- A set of fixes, and a conversion to blk-mq, of nbd. From Josef.
- Set of fixes and updates for lightnvm from Matias, Simon, and Arnd.
Followup dependency fix from Geert.
- General fixes from Bart, Baoyou, Guoqing, and Linus W.
- CFQ async write starvation fix from Glauber.
- Add supprot for delayed kick of the requeue list, from Mike.
- Pull out the scalable bitmap code from blk-mq-tag.c and make it
generally available under the name of sbitmap. Only blk-mq-tag uses
it for now, but the blk-mq scheduling bits will use it as well.
From Omar.
- bdev thaw error progagation from Pierre.
- Improve the blk polling statistics, and allow the user to clear
them. From Stephen.
- Set of minor cleanups from Christoph in block/blk-mq.
- Set of cleanups and optimizations from me for block/blk-mq.
- Various nvme/nvmet/nvmeof fixes from the various folks"
* 'for-4.9/block' of git://git.kernel.dk/linux-block: (54 commits)
fs/block_dev.c: return the right error in thaw_bdev()
nvme: Pass pointers, not dma addresses, to nvme_get/set_features()
nvme/scsi: Remove power management support
nvmet: Make dsm number of ranges zero based
nvmet: Use direct IO for writes
admin-cmd: Added smart-log command support.
nvme-fabrics: Add host_traddr options field to host infrastructure
nvme-fabrics: revise host transport option descriptions
nvme-fabrics: rework nvmf_get_address() for variable options
nbd: use BLK_MQ_F_BLOCKING
blkcg: Annotate blkg_hint correctly
cfq: fix starvation of asynchronous writes
blk-mq: add flag for drivers wanting blocking ->queue_rq()
blk-mq: remove non-blocking pass in blk_mq_map_request
blk-mq: get rid of manual run of queue with __blk_mq_run_hw_queue()
block: export bio_free_pages to other modules
lightnvm: propagate device_add() error code
lightnvm: expose device geometry through sysfs
lightnvm: control life of nvm_dev in driver
blk-mq: register device instead of disk
...
device_add() may fail, and all callers are supposed to check the
return value, but one new user in lightnvm doesn't:
drivers/lightnvm/sysfs.c: In function 'nvm_sysfs_register_dev':
drivers/lightnvm/sysfs.c:184:2: error: ignoring return value of 'device_add',
declared with attribute warn_unused_result [-Werror=unused-result]
This changes the caller to propagate any error codes, which avoids
the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 38c9e260b9f9 ("lightnvm: expose device geometry through sysfs")
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
For a host to access an Open-Channel SSD, it has to know its geometry,
so that it writes and reads at the appropriate device bounds.
Currently, the geometry information is kept within the kernel, and not
exported to user-space for consumption. This patch exposes the
configuration through sysfs and enables user-space libraries, such as
liblightnvm, to use the sysfs implementation to get the geometry of an
Open-Channel SSD.
The sysfs entries are stored within the device hierarchy, and can be
found using the "lightnvm" device type.
An example configuration looks like this:
/sys/class/nvme/
└── nvme0n1
├── capabilities: 3
├── device_mode: 1
├── erase_max: 1000000
├── erase_typ: 1000000
├── flash_media_type: 0
├── media_capabilities: 0x00000001
├── media_type: 0
├── multiplane: 0x00010101
├── num_blocks: 1022
├── num_channels: 1
├── num_luns: 4
├── num_pages: 64
├── num_planes: 1
├── page_size: 4096
├── prog_max: 100000
├── prog_typ: 100000
├── read_max: 10000
├── read_typ: 10000
├── sector_oob_size: 0
├── sector_size: 4096
├── media_manager: gennvm
├── ppa_format: 0x380830082808001010102008
├── vendor_opcode: 0
├── max_phys_secs: 64
└── version: 1
Signed-off-by: Simon A. F. Lund <slund@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
LightNVM compatible device drivers does not have a method to expose
LightNVM specific sysfs entries.
To enable LightNVM sysfs entries to be exposed, lightnvm device
drivers require a struct device to attach it to. To allow both the
actual device driver and lightnvm sysfs entries to coexist, the device
driver tracks the lifetime of the nvm_dev structure.
This patch refactors NVMe and null_blk to handle the lifetime of struct
nvm_dev, which eliminates the need for struct gendisk when a lightnvm
compatible device is provided.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
With LightNVM enabled namespaces, the gendisk structure is not exposed
to the user. This prevents LightNVM users from accessing the NVMe device
driver specific sysfs entries, and LightNVM namespace geometry.
Refactor the revalidation process, so that a namespace, instead of a
gendisk, is revalidated. This later allows patches to wire up the
sysfs entries up to a non-gendisk namespace.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
If NO_DMA=y:
drivers/built-in.o: In function `nvme_nvm_dev_dma_free':
lightnvm.c:(.text+0x23df1a): undefined reference to `dma_pool_free'
drivers/built-in.o: In function `nvme_nvm_dev_dma_alloc':
lightnvm.c:(.text+0x23df38): undefined reference to `dma_pool_alloc'
drivers/built-in.o: In function `nvme_nvm_destroy_dma_pool':
lightnvm.c:(.text+0x23df4c): undefined reference to `dma_pool_destroy'
drivers/built-in.o: In function `nvme_nvm_create_dma_pool':
lightnvm.c:(.text+0x23df7e): undefined reference to `dma_pool_create'
and
ERROR: "dma_pool_destroy" [drivers/nvme/host/nvme-core.ko] undefined!
ERROR: "dma_pool_free" [drivers/nvme/host/nvme-core.ko] undefined!
ERROR: "dma_pool_alloc" [drivers/nvme/host/nvme-core.ko] undefined!
ERROR: "dma_pool_create" [drivers/nvme/host/nvme-core.ko] undefined!
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch removes module_init()/module_exit() from driver code by using
module_misc_device() macro. All modules in this patch has a print
statement which is removed when module_misc_device() macro is used.
If undesirable this patch can be dropped entirely, this is the only
purpose of making this as a separate patch.
Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These two are confusing leftover of the old world order, combining
values of the REQ_OP_ and REQ_ namespaces. For callers that don't
special case we mostly just replace bi_rw with bio_data_dir or
op_is_write, except for the few cases where a switch over the REQ_OP_
values makes more sense. Any check for READA is replaced with an
explicit check for REQ_RAHEAD. Also remove the READA alias for
REQ_RAHEAD.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The __nvm_submit_ppa() function is not used outside lightnvm core.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The passed by reference ppa list in nvm_set_rqd_list() is updated when
multiple planes are available. In that case, each PPA plane is
incremented when the device side PPA list is created. This prevents the
caller to rely on the PPA list to be unmodified after a call.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The gen_mark_blk_bad function marks the wrong block when a block is on
a different channel. Fix the index calculation, so that it updates the
correct block.
Reported-by: Javier Gonzalez <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The nvm_get_blk() function is called with rlun->lock held. This is ok
when the media manager implementation doesn't go out of its atomic
context. However, if a media manager persists its metadata, and
guarantees that the block is given to the target, this is no longer
a viable approach. Therefore, clean up the flow of rrpc_map_page,
and make sure that nvm_get_blk() is called without any locks acquired.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The [get/put]_blk API enables targets to get ownership of blocks at
runtime. This information is currently not recorded on disk, and the
information is therefore lost on power failure. To restore the
metadata, the [get/put]_blk must persist its metadata. In that case,
we need to control the outer lock, so that we can disable them while
updating the on-disk metadata. Fortunately, the _unlocked versions can
be removed, which allows us to move the lock into the [get/put]_blk
functions.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The ->list, ->open_list, and ->closed_list lists were previously used
for statistics. However, their usage have been removed, and thus these
can safely be removed.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
If a media manager tries to initialize it targets upon media manager
initialization, the media manager will need to know which target types
are available in LightNVM. The lists of which managers and target types
are available shares the same lock.
Therefore, on initialization, the nvm_lock is taken by LightNVM core,
which later leads to a deadlock when target types are enumerated by the
media manager.
Add an exclusive lock for target types to resolve this conflict.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
To enable persistent block management to easily control creation and
removal of targets, we move target management into the media
manager. The LightNVM core continues to maintain which target types are
registered, while the media manager now keeps track of its initialized
targets.
Two new callbacks for the media manager are introduced. create_tgt and
remove_tgt. Note that remove_tgt returns 0 on successfully removing a
target, and returns 1 if the target was not found.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The generic manager should be called the general media manager, and
instead of using the rather long name of "gennvm" in front of each data
structures, use "gen" instead to shorten it. Update the description of
the media manager as well to make the media manager purpose clearer.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The responsibility of the media manager is not to keep track of
open/closed blocks. This is better maintained within a target,
that already manages this information on writes.
Remove the statistics and merge the states NVM_BLK_ST_OPEN and
NVM_BLK_ST_CLOSED.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
A couple of small checkpatch fixups to stop it from complaining.
./drivers/lightnvm/core.c:360: WARNING: line over 80 characters
./drivers/lightnvm/core.c:360: ERROR: trailing statements should be on
next line
./drivers/lightnvm/core.c:503: WARNING: Block comments use a trailing */
on a separate line
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Checkpatch found two incidents where the type was preferred to be
written out in full.
./drivers/lightnvm/rrpc.h:184: WARNING: Prefer 'unsigned int' to bare
use of 'unsigned'
./drivers/lightnvm/rrpc.h:209: WARNING: Prefer 'unsigned int' to bare
use of 'unsigned'
./drivers/lightnvm/rrpc.c:51: WARNING: Prefer 'unsigned int' to bare use
of 'unsigned'
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Mark functions not used by ouside of thier implementing file as static.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Expose media manager mark_blk() to targets, as done for the rest of the
media manager callback functions.
Signed-off-by: Javier González <javier@cnexlabs.com>
Updated description
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Break the loop when rqd is not null to reduce
an unnecessary schedule.
Signed-off-by: Wenwei Tao <ww.tao0320@gmail.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch converts the simple bi_rw use cases in the block,
drivers, mm and fs code to set/get the bio operation using
bio_set_op_attrs/bio_op
These should be simple one or two liner cases, so I just did them
in one patch. The next patches handle the more complicated
cases in a module per patch.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The nvm_dev->max_pages_per_blk variable was removed in favor of the new
nvm->sec_per_blk variable. The ->max_pages_per_blk variable was still
used in rrpc_capacity, reporting the reserved capacity to zero. Replace
with ->sec_per_blk to calculate the reserved area again.
Signed-off-by: Javier González <javier@cnexlabs.com>
Updated patch description. Was "lightnvm: eliminate redundant variable"
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The number of ppas contained on a request is not necessarily the number
of pages that it maps to neither on the target nor on the device side.
In order to avoid confusion, rename nr_pages to nr_ppas since it is what
the variable actually contains.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Targets can update a block state when having a reference to an
in-memory virtual block. In the case that a target does not keep the
block metadata in memory, it does not have a way to update this
structure.
Therefore, expose gennvm_mark_blk() through the media managers
->mark_blk() callback and let targets update the state structure through
this callback.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Targets associated with a device manager are not freed on device
removal. They have to be manually removed before shutdown. Make sure
any outstanding targets are freed upon shutdown.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Linus Torvalds
Javier González
Javier González
Matias Bjørling
Paul Gortmaker
Arnd Bergmann
Simon A. F. Lund
Geert Uytterhoeven
PrasannaKumar Muralidharan
Christoph Hellwig
Johannes Thumshirn
Wenwei Tao
Mike Christie