If we force the hw to idle as our first step during unload, we can abort
the unload upon failure. Later we can probe whether the hardware remain
active even after we try to shut it down.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So far we distinguished platforms without a dynamic power well with
the HAS_POWER_WELL macro and for such platforms we didn't call any power
domain functions. Instead of doing this check we can add an always-on
power well for these platforms and call the power domain functions
unconditionally. For always-on power wells we only increase/decrease
their refcounts, otherwise they are nop.
This makes high level driver code more readable and as a bonus provides
some idea of the current power domains state for all platforms (once
the relevant debugfs entry is added).
v3: rename intel_power_wells to i9xx_always_on_power_well (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our VM code already has a cleanup function, and this is a nice place to
put the drm_mm_takedown. This should have no functional impact, it just
leaves the unload function a bit cleaer, and is more logical IMO
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull in Jani's backlight rework branch. This was merged through a
separate branch to be able to sort out the Broadwell conflicts
properly before pulling it into the main development branch.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move from dev_priv to connector->panel. We still don't allow multiple
sysfs interfaces, though.
There should be no functional changes, except for a slight reordering of
connector backlight and sysfs destroy calls. (This change happens now
that the backlight device is actually per-connector, even though the
destroy calls became per-connector earlier.)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This ioctl returns reset stats for specified context.
The struct returned contains context loss counters.
reset_count: all resets across all contexts
batch_active: active batches lost on resets
batch_pending: pending batches lost on resets
v2: get rid of state tracking completely and deliver only counts. Idea
from Chris Wilson.
v3: fix commit message
v4: default context handled inside i915_gem_context_get_hang_stats
v5: reset_count only for priviledged process
v6: ctx=0 needs CAP_SYS_ADMIN for batch_* counters (Chris Wilson)
v7: context hang stats never returns NULL
v8: rebased on top of reworked context hang stats
DRM_RENDER_ALLOW for ioctl
v9: use DEFAULT_CONTEXT_ID. Improve comments for ioctl struct members
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Ian Romanick <idr@freedesktop.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I want to merge in the new Broadwell support as a late hw enabling
pull request. But since the internal branch was based upon our
drm-intel-nightly integration branch I need to resolve all the
oustanding conflicts in drm/i915 with a backmerge to make the 60+
patches apply properly.
We'll propably have some fun because Linus will come up with a
slightly different merge solution.
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_drv.c
drivers/gpu/drm/i915/intel_crt.c
drivers/gpu/drm/i915/intel_ddi.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
drivers/gpu/drm/i915/intel_drv.h
All rather simple adjacent lines changed or partial backports from
-next to -fixes, with the exception of the thaw code in i915_dma.c.
That one needed a bit of shuffling to restore the intent.
Oh and the massive header file reordering in intel_drv.h is a bit
trouble. But not much.
v2: Also don't forget the fixup for the silent conflict that results
in compile fail ...
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similarly rename the other related functions in the power domain
interface.
Higher level driver code calling these functions knows only about power
domains, not the underlying power wells which may be different on
different platforms. Also these functions really init/cleanup/resume
power domains and only through that all related power wells, so rename
them accordingly.
Note that I left i915_{request,release}_power_well as is, since that
really changes the state only of a single power well (and is HSW
specific). It should also get a better name once we make it more
generic by controlling things through a new audio power domain.
v4:
- use intel prefix instead of i915 everywhere (Paulo)
- use a $prefix_$block_$action format (Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we make sure that all power domains are enabled during driver
init and turn off unneded ones only after the first modeset. Similarly
during suspend we enable all power domains, which will remain on through
the following resume until the first modeset.
This logic is supported by intel_set_power_well() in the power domain
framework. It would be nice to simplify the API, so that we only have
get/put functions and make it more explicit on the higher level how this
"power well on during init" logic works. This will make it also easier
if in the future we want to shorten the time the power wells are on.
For this add a new device private flag tracking whether we have the
power wells on because of init/suspend and use only
intel_display_power_get()/put(). As nothing else uses
intel_set_power_well() we can remove it.
This also fixes
commit 6efdf354dd
Author: Imre Deak <imre.deak@intel.com>
Date: Wed Oct 16 17:25:52 2013 +0300
drm/i915: enable only the needed power domains during modeset
where removing intel_set_power_well() resulted in not releasing the
reference on the power well that was taken during init and thus leaving
the power well on all the time. Regression reported by Paulo.
v2:
- move the init_power_on flag to the power_domains struct (Daniel)
v3:
- add note about this being a regression fix too (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have two once very similar functions, i915_gpu_idle() and
i915_gem_idle(). The former is used as the lower level operation to
flush work on the GPU, whereas the latter is the high level interface to
flush the GEM bookkeeping in addition to flushing the GPU. As such
i915_gem_idle() also clears out the request and activity lists and
cancels the delayed work. This is what we need for unloading the driver,
unfortunately we called i915_gpu_idle() instead.
In the process, make sure that when cancelling the delayed work and
timer, which is synchronous, that we do not hold any locks to prevent a
deadlock if the work item is already waiting upon the mutex. This
requires us to push the mutex down from the caller to i915_gem_idle().
v2: s/i915_gem_idle/i915_gem_suspend/
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=70334
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: xunx.fang@intel.com
[danvet: Only set ums.suspended for !kms as discussed earlier. Chris
noticed that this slipped through.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
seq_file is not quite the right interface for these ones. We have a
circular buffer with a new entry per vblank on one side and a process
wanting to dequeue the CRC with a read().
It's quite racy to wait for vblank in user land and then try to read a
pipe_crc file, sometimes the CRC interrupt hasn't been fired and we end
up with an EOF.
So, let's have the read on the pipe_crc file block until the interrupt
gives us a new entry. At that point we can wake the reading process.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This file is all about the legacy fbdev support. If we want to extract
framebuffer functions, we better put those into a separate file.
Also rename functions accordingly, only two have used the intel_fb_
prefix anyway.
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Boots Just Fine (tm)!
The only glitch seems to be that at least on Fedora the boot splash
gets confused and doesn't display much at all.
And since there's no ugly console flickering anymore in between, the
flicker while switching between X servers (VT support is still enabled)
is even more jarring.
Also, I'm unsure whether we don't need to somehow kick out vgacon, now
that nothing else gets in the way. But stuff seems to work, so I
don't care. Also everything still works as well with VGA_CONSOLE=n
Also the #ifdef mess needs a bit of a cleanup, follow-up patches will
do just that.
To keep the Kconfig tidy, extract all the i915 options into its own
file.
v2:
- Rebase on top of the preliminary hw support option and the
intel_drv.h cleanup.
- Shut up warnings in i915_debugfs.c
v3: Use the right CONFIG variable, spotted by Chon Ming.
Cc: Lee, Chon Ming <chon.ming.lee@intel.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 81b5c7bc8d.
Adding drm/i915 into the vga arbiter chain means that X (in a piece of
well-meant paranoia) will do a get/put on the vga decoding around
_every_ accel call down into the ddx. Which results in some nice
performance disasters [1]. This really breaks userspace, by disabling
DRI for everyone, and stops OpenGL from working, this isn't limited
to just the i915 but both the integrated and discrete GPUs on
multi-gpu systems, in other words this causes untold worlds of pain,
Ville tried to come up with a Great Hack to fiddle the required VGA
I/O ops behind everyone's back using stop_machine, but that didn't
really work out [2]. Given that we're fairly late in the -rc stage for
such games let's just revert this all.
One thing we might want to keep is to delay the disabling of the vga
decoding until the fbdev emulation and the fbcon screen is set up. If
we kill vga mem decoding beforehand fbcon can end up with a white
square in the top-left corner it tried to save from the vga memory for
a seamless transition. And we have bug reports on older platforms
which seem to match these symptoms.
But again that's something to play around with in -next.
References: [1] http://lists.x.org/archives/xorg-devel/2013-September/037763.html
References: [2] http://www.spinics.net/lists/intel-gfx/msg34062.html
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit 6e1b4fdad5.
This is part of a revert due to a userspace breakage, better explained in the revert of 1a1a4cbf4906a13c0c377f708df5d94168e7b582.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Educate the users why i915 won't load on gen6+ and nomodeset.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=61671
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For future platforms we'll need to initialize our MMIO function pointers
even earlier. Specifically, we'll need to be able to have register
reads/writes at GTT initialization (in i915_gem_gtt_init). Similarly,
these platforms also have MMIO differences based on the PCH id, so
while moving stuff around, also move the PCH initialization.
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Mention the function where we need register access.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In order to be able to have virtual functions for the MMIO, we need to
use the raw access function. To keep things simple, just move this to
our early_sanitize code in uncore.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For upcoming patches which will have GEN specific MMIO functions, we'll
need to initialize the uncore data structure earlier than we do today.
If we do not do this, the following will be problematic:
intel_uncore_sanitize
intel_disable_gt_powersave
gen6_disable_rps
I915_WRITE(GEN6_RC_CONTROL, 0); <--- MMIO
intel_uncore_init // initializes MMIO
By initializing the function pointers first, we should be safe.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The conflict in intel_drv.h tripped me up a bit since a patch in dinq
moves all the functions around, but another one in drm-next removes a
single function. So I'ev figured backing this into a backmerge would
be good.
i915_dma.c is just adjacent lines changed, nothing nefarious there.
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/intel_drv.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The user of these counters was killed in
commit d79cdc8312
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Aug 8 15:41:32 2013 +0200
drm: no-op out GET_STATS ioctl
so clean up the leftovers as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We can get the PCI vendor and device IDs via dev->pdev. So we can drop
the duplicated information.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
vblank_disable_allowed is only ever 0 or 1, so make it a bool.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If we encounter a situation where the CPU blocks waiting for results
from the GPU, give the GPU a kick to boost its the frequency.
This should work to reduce user interface stalls and to quickly promote
mesa to high frequencies - but the cost is that our requested frequency
stalls high (as we do not idle for long enough before rc6 to start
reducing frequencies, nor are we aggressive at down clocking an
underused GPU). However, this should be mitigated by rc6 itself powering
off the GPU when idle, and that energy use is dependent upon the workload
of the GPU in addition to its frequency (e.g. the math or sampler
functions only consume power when used). Still, this is likely to
adversely affect light workloads.
In particular, this nearly eliminates the highly noticeable wake-up lag
in animations from idle. For example, expose or workspace transitions.
(However, given the situation where we fail to downclock, our requested
frequency is almost always the maximum, except for Baytrail where we
manually downclock upon idling. This often masks the latency of
upclocking after being idle, so animations are typically smooth - at the
cost of increased power consumption.)
Stéphane raised the concern that this will punish good applications and
reward bad applications - but due to the nature of how mesa performs its
client throttling, I believe all mesa applications will be roughly
equally affected. To address this concern, and to prevent applications
like compositors from permanently boosting the RPS state, we ratelimit the
frequency of the wait-boosts each client recieves.
Unfortunately, this techinique is ineffective with Ironlake - which also
has dynamic render power states and suffers just as dramatically. For
Ironlake, the thermal/power headroom is shared with the CPU through
Intelligent Power Sharing and the intel-ips module. This leaves us with
no GPU boost frequencies available when coming out of idle, and due to
hardware limitations we cannot change the arbitration between the CPU and
GPU quickly enough to be effective.
v2: Limit each client to receiving a single boost for each active period.
Tested by QA to only marginally increase power, and to demonstrably
increase throughput in games. No latency measurements yet.
v3: Cater for front-buffer rendering with manual throttling.
v4: Tidy up.
v5: Sadly the compositor needs frequent boosts as it may never idle, but
due to its picking mechanism (using ReadPixels) may require frequent
waits. Those waits, along with the waits for the vrefresh swap, conspire
to keep the GPU at low frequencies despite the interactive latency. To
overcome this we ditch the one-boost-per-active-period and just ratelimit
the number of wait-boosts each client can receive.
Reported-and-tested-by: Paul Neumann <paul104x@yahoo.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68716
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Cc: Stéphane Marchesin <stephane.marchesin@gmail.com>
Cc: Owen Taylor <otaylor@redhat.com>
Cc: "Meng, Mengmeng" <mengmeng.meng@intel.com>
Cc: "Zhuang, Lena" <lena.zhuang@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: No extern for function prototypes in headers.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We missed adding a few cleanup steps for recent additions.
Reviewer: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Obtaining the forcwake requires expensive and time consuming
serialisation. And we often try to obtain the forcewake multiple times
in very quick succession. We can reduce the overhead of these sequences
by delaying the forcewake release, and so not hammer the hw quite so
hard.
I was hoping this would help with the spurious
[drm:__gen6_gt_force_wake_mt_get] *ERROR* Timed out waiting for forcewake old ack to clear.
found on Haswell. Alas not.
v2: Fix teardown ordering - unmap the regs after turning off forcewake,
and make sure we do turn off forcewake - both found by Ville.
v3: As we introduce intel_uncore_fini(), use it to make sure everything
is disabled before we hand back to the BIOS.
Note: I have no claims for improved performance, stablity or power
comsumption for this patch. We should not be hitting the registers often
enough for this to improve benchmarks, but given the nature of our hw it
is likely to improve long term stability.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_modeset_init() will already attempt to disable VGA. In order to do
that, it needs the power well to be on. So move the power well init
to happen before intel_modeset_init() during driver load.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VGA registers live inside the power well on HSW, so in order to write
the VGA MSR register we need the power well to be on.
We really must write to the register to properly clear the
VGA_MSR_MEM_EN enable bit, even if all VGA registers get zeroed when
the power well is down. It seems that the implicit zeroing done by
the power well is not enough to propagate the VGA_MSR_MEM_EN bit to
whomever is actually responsible for the memory decode ranges.
If we leave VGA memory decode enabled, and then turn off the power well,
all VGA memory reads will return zeroes. But if we first disable VGA
memory deocde and then turn off the power well, VGA memory reads
return all ones, indicating that the access wasn't claimed by anyone.
For the vga arbiter to function correctly the IGD must not claim the
VGA memory accesses.
Previously we were doing the VGA_MSR register access while the power well
was excplicitly powered up during driver init. But ever since
commit 6e1b4fdad5
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Thu Sep 5 20:40:52 2013 +0300
drm/i915: Delay disabling of VGA memory until vgacon->fbcon handoff is done
we delay the VGA memory disable until fbcon has initialized, and so
there's a possibility that the power well got turned off during the
fbcon modeset. Also vgacon_save_screen() will need the power well to be
on to be able to read the VGA memory.
So immediately after enabling the power well during init grab a refence
for VGA purposes, and after all the VGA handling is done, release it.
v2: Add intel_display_power_put() for the num_pipes==0 case
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix up the patch wiggle screw-up that I've done and which
Paulo catched. Also polish spelling in the patch headline.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Done while reviewing all our allocations for fubar. Also a few errant
cases of lacking () for the sizeof operator - just a bit of OCD.
I've left out all the conversions that also should use kcalloc from
this patch (it's only 2).
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSQMORAAoJEHm+PkMAQRiGj14H/1bjhtfNjPdX7MVQAzA+WpwX
s7h1IQu2Si9S5S1lBiM2sBTOssVcmfheO9x4yqm7JNOD1RnssWKOM3q+zVOLstwd
GD3gluJPeraD5EyYSqEJ9ILPQ3gbxb4wOlT0Z291TW6E8XhLRr0RTOJPksRsgvLH
Ckm9uJh6ArS6ZXfXiaDQfd+xHAQJkUfW6nMSA0g9ZO9C6KIDRvcbUmrY3m4HhfIk
mK0TXCBs+AXGDIjTEB8JgIQL/5y1Qn0c4R+2uTU/4YWwyLvJTV1e44kGoleukMMT
6Pw/TNlUEN161dbSaqCyF3sfXHDYQ5valycI2PDgitMtPSxbzsU1VDizS8+daRg=
=lEmF
-----END PGP SIGNATURE-----
Merge tag 'v3.12-rc2' into drm-intel-next
Backmerge Linux 3.12-rc2 to prep for a bunch of -next patches:
- Header cleanup in intel_drv.h, both changed in -fixes and my current
-next pile.
- Cursor handling cleanup for -next which depends upon the cursor
handling fix merged into -rc2.
All just trivial conflicts of the "changed adjacent lines" type:
drivers/gpu/drm/i915/i915_gem.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_drv.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The init and resume codepaths want to handel the power well in slightly
different ways, so pull the power well init out from
intel_modeset_init_hw() which gets called in both cases.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull vfs pile 4 from Al Viro:
"list_lru pile, mostly"
This came out of Andrew's pile, Al ended up doing the merge work so that
Andrew didn't have to.
Additionally, a few fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (42 commits)
super: fix for destroy lrus
list_lru: dynamically adjust node arrays
shrinker: Kill old ->shrink API.
shrinker: convert remaining shrinkers to count/scan API
staging/lustre/libcfs: cleanup linux-mem.h
staging/lustre/ptlrpc: convert to new shrinker API
staging/lustre/obdclass: convert lu_object shrinker to count/scan API
staging/lustre/ldlm: convert to shrinkers to count/scan API
hugepage: convert huge zero page shrinker to new shrinker API
i915: bail out earlier when shrinker cannot acquire mutex
drivers: convert shrinkers to new count/scan API
fs: convert fs shrinkers to new scan/count API
xfs: fix dquot isolation hang
xfs-convert-dquot-cache-lru-to-list_lru-fix
xfs: convert dquot cache lru to list_lru
xfs: rework buffer dispose list tracking
xfs-convert-buftarg-lru-to-generic-code-fix
xfs: convert buftarg LRU to generic code
fs: convert inode and dentry shrinking to be node aware
vmscan: per-node deferred work
...
Convert the driver shrinkers to the new API. Most changes are compile
tested only because I either don't have the hardware or it's staging
stuff.
FWIW, the md and android code is pretty good, but the rest of it makes me
want to claw my eyes out. The amount of broken code I just encountered is
mind boggling. I've added comments explaining what is broken, but I fear
that some of the code would be best dealt with by being dragged behind the
bike shed, burying in mud up to it's neck and then run over repeatedly
with a blunt lawn mower.
Special mention goes to the zcache/zcache2 drivers. They can't co-exist
in the build at the same time, they are under different menu options in
menuconfig, they only show up when you've got the right set of mm
subsystem options configured and so even compile testing is an exercise in
pulling teeth. And that doesn't even take into account the horrible,
broken code...
[glommer@openvz.org: fixes for i915, android lowmem, zcache, bcache]
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Glauber Costa <glommer@openvz.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: Arve Hjønnevåg <arve@android.com>
Cc: Carlos Maiolino <cmaiolino@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Chuck Lever <chuck.lever@oracle.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Rientjes <rientjes@google.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: J. Bruce Fields <bfields@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Ignoring the legacy DRI1 code, and a couple of special cases (to be
discussed later), all access to the ring is mediated through requests.
The first write to a ring will grab a seqno and mark the ring as having
an outstanding_lazy_request. Either through explicitly adding a request
after an execbuffer or through an implicit wait (either by the CPU or by
a semaphore), that sequence of writes will be terminated with a request.
So we can ellide all the intervening writes to the tail register and
send the entire command stream to the GPU at once. This will reduce the
number of *serialising* writes to the tail register by a factor or 3-5
times (depending upon architecture and number of workarounds, context
switches, etc involved). This becomes even more noticeable when the
register write is overloaded with a number of debugging tools. The
astute reader will wonder if it is then possible to overflow the ring
with a single command. It is not. When we start a command sequence to
the ring, we check for available space and issue a wait in case we have
not. The ring wait will in this case be forced to flush the outstanding
register write and then poll the ACTHD for sufficient space to continue.
The exception to the rule where everything is inside a request are a few
initialisation cases where we may want to write GPU commands via the CS
before userspace wakes up and page flips.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When transitioning away from vgacon the system tries to save the
current contents of the VGA memory, so that it can be cleanly handed
off to fbcon (or whatever comes afterwards).
The recent change
commit 81b5c7bc8d
Author: Alex Williamson <alex.williamson@redhat.com>
Date: Wed Aug 28 09:39:08 2013 -0600
i915: Update VGA arbiter support for newer devices
caused i915 to disable VGA memory decode for the IGD when i915 is
initializing. Unfortunately that happens before the vgacon->fbcon
handoff so vgacon_save_screen() will read out all ones from the
VGA memory.
After the handoff fbcon will inherit the bogus state from vgacon,
and pre-fills the fb with matching contents. The end result is
a white rectangle in the top left corner of the screen, the size
of which matches the now inactive VGA console.
To remedy the situation delay the disabling of VGA memory until
the vgacon->fbcon handoff has happened.
Also rename i915_enable_vga to i915_enable_vga_mem to make
the relationship between these functions clearer.
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is intended to add VGA arbiter support for Intel HD graphics on
Core processors. The old GMCH registers no longer exist, so even
though it appears that i915 participates in VGA arbitration, it doesn't
work. On Intel HD graphics we already attempt to disable VGA regions
of the device. This makes registering as a VGA client unnecessary since
we don't intend to operate differently depending on how many VGA devices
are present. We can disable VGA memory regions by clearing the memory
enable bit in the VGA MSR. That only leaves VGA IO, which we update
the VGA arbiter to know that we don't participate in VGA memory
arbitration. We also add a hook on unload to re-enable memory and
reinstate VGA memory arbitration.
v3: Use explicit LEGACY_IO | LEGACY_MEM when restoring rather than
LEGACY_MASK, per Ville's comments.
v2: I915_READ/WRITE accessors don't work in i915_disable_vga, use inb/outb
directly. Also, on the driver unbind VGA enable path, acquire legacy
IO to re-enable VGA memory. Correct comment.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add patch changelog. Also squash in a fixup to have a dummy
static inline for vga_set_legacy_decoding for CONFIG_VGA_ARB=n as
reported by the 0-day kernel build bot.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
fixup 2
Enable support for drm render nodes for i915 by flagging the ioctls that
are safe and just needed for rendering.
v2: mark reg_read, set_caching and get_caching (ickle, danvet)
Signed-off-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Need to get my stuff out the door ;-) Highlights:
- pc8+ support from Paulo
- more vma patches from Ben.
- Kconfig option to enable preliminary support by default (Josh
Triplett)
- Optimized cpu cache flush handling and support for write-through caching
of display planes on Iris (Chris)
- rc6 tuning from Stéphane Marchesin for more stability
- VECS seqno wrap/semaphores fix (Ben)
- a pile of smaller cleanups and improvements all over
Note that I've ditched Ben's execbuf vma conversion for 3.12 since not yet
ready. But there's still other vma conversion stuff in here.
* tag 'drm-intel-next-2013-08-23' of git://people.freedesktop.org/~danvet/drm-intel: (62 commits)
drm/i915: Print seqnos as unsigned in debugfs
drm/i915: Fix context size calculation on SNB/IVB/VLV
drm/i915: Use POSTING_READ in lcpll code
drm/i915: enable Package C8+ by default
drm/i915: add i915.pc8_timeout function
drm/i915: add i915_pc8_status debugfs file
drm/i915: allow package C8+ states on Haswell (disabled)
drm/i915: fix SDEIMR assertion when disabling LCPLL
drm/i915: grab force_wake when restoring LCPLL
drm/i915: drop WaMbcDriverBootEnable workaround
drm/i915: Cleaning up the relocate entry function
drm/i915: merge HSW and SNB PM irq handlers
drm/i915: fix how we mask PMIMR when adding work to the queue
drm/i915: don't queue PM events we won't process
drm/i915: don't disable/reenable IVB error interrupts when not needed
drm/i915: add dev_priv->pm_irq_mask
drm/i915: don't update GEN6_PMIMR when it's not needed
drm/i915: wrap GEN6_PMIMR changes
drm/i915: wrap GTIMR changes
drm/i915: add the FCLK case to intel_ddi_get_cdclk_freq
...
For optimus and powerxpress muxless we really want the GPU
driver deciding when to power up/down the GPU, not userspace.
This adds the ability for a driver to dynamically power up/down
the GPU and remove the switcheroo from controlling it, the
switcheroo reports the dynamic state to userspace also.
It also adds 2 power domains, one for machine where the power
switch is controlled outside the GPU D3 state, so the powerdown
ordering is done correctly, and the second for the hdmi audio
device to make sure it can resume for PCI config space accesses.
v1.1: fix build with switcheroo off
v2: add power domain support for radeon and v1 nvidia dsms
v2.1: fix typo in off case
v3: add audio power domain for hdmi audio + misc audio fixes
v4: use PCI_SLOT macro, drop power reference on hdmi audio resume
failure also.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch allows PC8+ states on Haswell. These states can only be
reached when all the display outputs are disabled, and they allow some
more power savings.
The fact that the graphics device is allowing PC8+ doesn't mean that
the machine will actually enter PC8+: all the other devices also need
to allow PC8+.
For now this option is disabled by default. You need i915.allow_pc8=1
if you want it.
This patch adds a big comment inside i915_drv.h explaining how it
works and how it tracks things. Read it.
v2: (this is not really v2, many previous versions were already sent,
but they had different names)
- Use the new functions to enable/disable GTIMR and GEN6_PMIMR
- Rename almost all variables and functions to names suggested by
Chris
- More WARNs on the IRQ handling code
- Also disable PC8 when there's GPU work to do (thanks to Ben for
the help on this), so apps can run caster
- Enable PC8 on a delayed work function that is delayed for 5
seconds. This makes sure we only enable PC8+ if we're really
idle
- Make sure we're not in PC8+ when suspending
v3: - WARN if IRQs are disabled on __wait_seqno
- Replace some DRM_ERRORs with WARNs
- Fix calls to restore GT and PM interrupts
- Use intel_mark_busy instead of intel_ring_advance to disable PC8
v4: - Use the force_wake, Luke!
v5: - Remove the "IIR is not zero" WARNs
- Move the force_wake chunk to its own patch
- Only restore what's missing from RC6, not everything
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our driver initialization doesn't seem to be ready to load when the
power well is disabled: we hit a few "Unclaimed register" messages. So
do just like we already do for the suspend/resume path: enable the
power well before unloading.
At some point we'll want to be able to survive suspend/resume and
load/unload with the power well disabled, but for now let's just fix
the regression.
Regression introduced by the following commit:
commit bf51d5e2cd
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Wed Jul 3 17:12:13 2013 -0300
drm/i915: switch disable_power_well default value to 1
Bug can be reproduced by running the "module_reload" script from
intel-gpu-tools.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67813
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The machines that fall in this category are the SDVs that have a PCI
ID starting with 0x0C. These are very early pre-production machines
and may not fully work. Other Haswell SDVs have PCI IDs that match the
real Haswell machines and we expect them to work better.
Even though they have problems, they still mostly work so I don't see
a reason to refuse loading our driver. But I do see a reason to reject
bug reports from these machines, so the message should help the bug
triagers.
As far as I know, we don't implement some workarounds that are
specific to these machines and suspend/resume may not work on most of
them, but besides this, they may work.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=61508
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Haswell GT3e has the unique feature of supporting Write-Through cacheing
of objects within the eLLC/LLC. The purpose of this is to enable the display
plane to remain coherent whilst objects lie resident in the eLLC/LLC - so
that we, in theory, get the best of both worlds, perfect display and fast
access.
However, we still need to be careful as the CPU does not see the WT when
accessing the cache. In particular, this means that we need to flush the
cache lines after writing to an object through the CPU, and on
transitioning from a cached state to WT.
v2: Actually do the clflush on transition to WT, nagging by Ville.
v3: Flush the CPU cache after writes into WT objects.
v4: Rease onto LLC updates and report WT as "uncached" for
get_cache_level_ioctl to remain symmetric with set_cache_level_ioctl.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
New pile of stuff for -next:
- Cleanup of the old crtc helper callbacks, all encoders are now converted
to the i915 modeset infrastructure.
- Massive amount of wm patches from Ville for ilk, snb, ivb, hsw, this is
prep work to eventually get things going for nuclear pageflips where we
need to adjust watermarks on the fly.
- More vm/vma patches from Ben. This refactoring isn't yet fully rolled
out, we miss the execbuf conversion and some of the low-level
bind/unbind support code.
- Convert our hdmi infoframe code to use the new common helper functions
(Damien). This contains some bugfixes for the common infoframe helpers.
- Some cruft removal from Damien.
- Various smaller bits&pieces all over, as usual.
* tag 'drm-intel-next-2013-08-09' of git://people.freedesktop.org/~danvet/drm-intel: (105 commits)
drm/i915: Fix FB WM for HSW
drm/i915: expose HDMI connectors on port C on BYT
drm/i915: fix a limit check in hsw_compute_wm_results()
drm/i915: unbreak i915_gem_object_ggtt_unbind()
drm/i915: Make intel_set_mode() static
drm/i915: Remove intel_modeset_disable()
drm/i915: Make intel_encoder_dpms() static
drm/i915: Make i915_hangcheck_elapsed() static
drm/i915: Fix #endif comment
drm/i915: Remove i915_gem_object_check_coherency()
drm/i915: Remove stale prototypes
drm/i915: List objects allocated from stolen memory in debugfs
drm/i915: Always call intel_update_sprite_watermarks() when disabling a plane
drm/i915: Pass plane and crtc to intel_update_sprite_watermarks
drm/i915: Don't try to disable plane if it's already disabled
drm/i915: Pass crtc to our update/disable_plane hooks
drm/i915: Split plane watermark parameters into a separate struct
drm/i915: Pull some watermarks state into a separate structure
drm/i915: Calculate max watermark levels for ILK+
drm/i915: Rename hsw_lp_wm_result to intel_wm_level
...
Merge the rcar stable branch that is being shared with the arm-soc tree.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* pfdo/drm-rcar-for-v3.12: (220 commits)
drm/rcar-du: Add FBDEV emulation support
drm/rcar-du: Add internal LVDS encoder support
drm/rcar-du: Configure RGB output routing to DPAD0
drm/rcar-du: Rework output routing support
drm/rcar-du: Add support for DEFR8 register
drm/rcar-du: Add support for multiple groups
drm/rcar-du: Fix buffer pitch alignment for R8A7790 DU
drm/rcar-du: Add support for the R8A7790 DU
drm/rcar-du: Move output routing configuration to group
drm/rcar-du: Remove register definitions for the second channel
drm/rcar-du: Use dynamic number of CRTCs instead of CRTCs array size
drm/rcar-du: Introduce CRTCs groups
drm/rcar-du: Rename rcar_du_plane_(init|register) to rcar_du_planes_*
drm/rcar-du: Create rcar_du_planes structure
drm/rcar-du: Rename platform data fields to match what they describe
drm/rcar-du: Merge LVDS and VGA encoder code
drm/rcar-du: Split VGA encoder and connector
drm/rcar-du: Split LVDS encoder and connector
drm/rcar-du: Clarify comment regarding plane Y source coordinate
drm/rcar-du: Support per-CRTC clock and IRQ
...
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/intel_pm.c
drivers/gpu/drm/qxl/qxl_release.c
Neat that QA (and Ben) keeps on humming along while I'm on vacation, so
you already get the next feature pull request:
- proper eLLC support for HSW from Ben
- more interrupt refactoring
- add w/a tags where we implement them already (Damien)
- hangcheck fixes (Chris) + hangcheck stats (Mika)
- flesh out the new vm structs for ppgtt and ggtt (Ben)
- PSR for Haswell, still disabled by default (Rodrigo et al.)
- pc8+ refclock sequence code from Paulo
- more interrupt refactoring from Paulo, unifying ilk/snb with the ivb/hsw
interrupt code
- full solution for the Haswell concurrent reg access issues (Chris)
- fix racy object accounting, used by some new leak tests
- fix sync polarity settings on ch7xxx dvo encoder
- random bits&pieces, little fixes and better debug output all over
[airlied: fix conflict with drm_mm cleanups]
* tag 'drm-intel-next-2013-07-26-fixed' of git://people.freedesktop.org/~danvet/drm-intel: (289 commits)
drm/i915: Do not dereference NULL crtc or fb until after checking
drm/i915: fix pnv display core clock readout out
drm/i915: Replace open-coded offset_in_page()
drm/i915: Retry DP aux_ch communications with a different clock after failure
drm/i915: Add messages useful for HPD storm detection debugging (v2)
drm/i915: dvo_ch7xxx: fix vsync polarity setting
drm/i915: fix the racy object accounting
drm/i915: Convert the register access tracepoint to be conditional
drm/i915: Squash gen lookup through multiple indirections inside GT access
drm/i915: Use the common register access functions for NOTRACE variants
drm/i915: Use a private interface for register access within GT
drm/i915: Colocate all GT access routines in the same file
drm/i915: fix reference counting in i915_gem_create
drm/i915: Use Graphics Base of Stolen Memory on all gen3+
drm/i915: disable stolen mem for OVERLAY_NEEDS_PHYSICAL
drm/i915: add functions to disable and restore LCPLL
drm/i915: disable CLKOUT_DP when it's not needed
drm/i915: extend lpt_enable_clkout_dp
drm/i915: fix up error cleanup in i915_gem_object_bind_to_gtt
drm/i915: Add some debug breadcrumbs to connector detection
...
Because, there is no reason for it not to be const.
v1: original
v2: fix compile break in vmwgfx, and couple related cleanups suggested
by Ville Syrjälä
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Move all the similar address space (VM) initialization code to one
function. Until we have multiple VMs, there should only ever be 1 VM.
The aliasing ppgtt is a special case without it's own VM (since it
doesn't need it's own address space management).
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm fixes from Dave Airlie:
"This is just a regular fixes pull apart from the qxl one, it has
radeon and intel bits in it,
The intel fixes are for a regression with the RC6 fix and a 3.10 hdmi
regression, whereas radeon is more DPM fixes, a few lockup fixes and
some rn50/r100 DAC fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/dpm: fix r600_enable_sclk_control()
drm/radeon/dpm: implement force performance levels for rv6xx
drm/radeon/dpm: fix displaygap programming on rv6xx
drm/radeon/dpm: fix a typo in the rv6xx mclk setup
drm/i915: initialize gt_lock early with other spin locks
drm/i915: fix hdmi portclock limits
drm/radeon: fix combios tables on older cards
drm/radeon: improve dac adjust heuristics for legacy pdac
drm/radeon: Another card with wrong primary dac adj
drm/radeon: fix endian issues with DP handling (v3)
drm/radeon/vm: only align the pt base to 32k
drm/radeon: wait for 3D idle before using CP DMA
- Revert of the ACPI video commit that I hoped would help fix
backlight problems related to Windows 8 compatibility on some
systems. Unfortunately, it turned out to cause problems to happen
too.
- Fix for two problems in intel_pstate, a possible failure to respond
to a load change on a quiet system and a possible failure to select
the highest available P-state on some systems. From Dirk Brandewie.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=mGfr
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are just two fixes, a revert of the would-be backlight fix that
didn't work and an intel_pstate fix for two problems related to
maximum P-state selection.
Specifics:
- Revert of the ACPI video commit that I hoped would help fix
backlight problems related to Windows 8 compatibility on some
systems. Unfortunately, it turned out to cause problems to happen
too.
- Fix for two problems in intel_pstate, a possible failure to respond
to a load change on a quiet system and a possible failure to select
the highest available P-state on some systems. From Dirk
Brandewie"
* tag 'pm+acpi-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI / video / i915: No ACPI backlight if firmware expects Windows 8"
cpufreq / intel_pstate: Change to scale off of max P-state
Chris Wilson
Imre Deak
Ben Widawsky
Daniel Vetter
Jani Nikula
Mika Kuoppala
Damien Lespiau
Dave Airlie
Ville Syrjälä
Linus Torvalds
Dave Chinner
Alex Williamson
Kristian Høgsberg
Dave Airlie
Paulo Zanoni
Dave Airlie
Rob Clark
Ben Widawsky