Pull RAS updates from Ingo Molnar:
"The main changes in this cycle are:
- RAS tracing/events infrastructure, by Gong Chen.
- Various generalizations of the APEI code to make it available to
non-x86 architectures, by Tomasz Nowicki"
* 'x86-ras-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/ras: Fix build warnings in <linux/aer.h>
acpi, apei, ghes: Factor out ioremap virtual memory for IRQ and NMI context.
acpi, apei, ghes: Make NMI error notification to be GHES architecture extension.
apei, mce: Factor out APEI architecture specific MCE calls.
RAS, extlog: Adjust init flow
trace, eMCA: Add a knob to adjust where to save event log
trace, RAS: Add eMCA trace event interface
RAS, debugfs: Add debugfs interface for RAS subsystem
CPER: Adjust code flow of some functions
x86, MCE: Robustify mcheck_init_device
trace, AER: Move trace into unified interface
trace, RAS: Add basic RAS trace event
x86, MCE: Kill CPU_POST_DEAD
Pull x86 platform updates from Ingo Molnar:
"The main changes in this cycle are:
- Intel SOC driver updates, by Aubrey Li.
- TS5500 platform updates, by Vivien Didelot"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pmc_atom: Silence shift wrapping warnings in pmc_sleep_tmr_show()
x86/pmc_atom: Expose PMC device state and platform sleep state
x86/pmc_atom: Eisable a few S0ix wake up events for S0ix residency
x86/platform: New Intel Atom SOC power management controller driver
x86/platform/ts5500: Add support for TS-5400 boards
x86/platform/ts5500: Add a 'name' sysfs attribute
x86/platform/ts5500: Use the DEVICE_ATTR_RO() macro
Pull x86 mm changes from Ingo Molnar:
"The main change in this cycle is the rework of the TLB range flushing
code, to simplify, fix and consolidate the code. By Dave Hansen"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Set TLB flush tunable to sane value (33)
x86/mm: New tunable for single vs full TLB flush
x86/mm: Add tracepoints for TLB flushes
x86/mm: Unify remote INVLPG code
x86/mm: Fix missed global TLB flush stat
x86/mm: Rip out complicated, out-of-date, buggy TLB flushing
x86/mm: Clean up the TLB flushing code
x86/smep: Be more informative when signalling an SMEP fault
Pull EFI changes from Ingo Molnar:
"Main changes in this cycle are:
- arm64 efi stub fixes, preservation of FP/SIMD registers across
firmware calls, and conversion of the EFI stub code into a static
library - Ard Biesheuvel
- Xen EFI support - Daniel Kiper
- Support for autoloading the efivars driver - Lee, Chun-Yi
- Use the PE/COFF headers in the x86 EFI boot stub to request that
the stub be loaded with CONFIG_PHYSICAL_ALIGN alignment - Michael
Brown
- Consolidate all the x86 EFI quirks into one file - Saurabh Tangri
- Additional error logging in x86 EFI boot stub - Ulf Winkelvos
- Support loading initrd above 4G in EFI boot stub - Yinghai Lu
- EFI reboot patches for ACPI hardware reduced platforms"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
efi/arm64: Handle missing virtual mapping for UEFI System Table
arch/x86/xen: Silence compiler warnings
xen: Silence compiler warnings
x86/efi: Request desired alignment via the PE/COFF headers
x86/efi: Add better error logging to EFI boot stub
efi: Autoload efivars
efi: Update stale locking comment for struct efivars
arch/x86: Remove efi_set_rtc_mmss()
arch/x86: Replace plain strings with constants
xen: Put EFI machinery in place
xen: Define EFI related stuff
arch/x86: Remove redundant set_bit(EFI_MEMMAP) call
arch/x86: Remove redundant set_bit(EFI_SYSTEM_TABLES) call
efi: Introduce EFI_PARAVIRT flag
arch/x86: Do not access EFI memory map if it is not available
efi: Use early_mem*() instead of early_io*()
arch/ia64: Define early_memunmap()
x86/reboot: Add EFI reboot quirk for ACPI Hardware Reduced flag
efi/reboot: Allow powering off machines using EFI
efi/reboot: Add generic wrapper around EfiResetSystem()
...
Pull x86 cpufeature updates from Ingo Molnar:
"The main changes in this cycle were:
- Continued cleanups of CPU bugs mis-marked as 'missing features', by
Borislav Petkov.
- Detect the xsaves/xrstors feature and releated cleanup, by Fenghua
Yu"
* 'x86-cpufeature-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, cpu: Kill cpu_has_mp
x86, amd: Cleanup init_amd
x86/cpufeature: Add bug flags to /proc/cpuinfo
x86, cpufeature: Convert more "features" to bugs
x86/xsaves: Detect xsaves/xrstors feature
x86/cpufeature.h: Reformat x86 feature macros
Pull x86 build/cleanup/debug updates from Ingo Molnar:
"Robustify the build process with a quirk to avoid GCC reordering
related bugs.
Two code cleanups.
Simplify entry_64.S CFI annotations, by Jan Beulich"
* 'x86-build-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, build: Change code16gcc.h from a C header to an assembly header
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Simplify __HAVE_ARCH_CMPXCHG tests
x86/tsc: Get rid of custom DIV_ROUND() macro
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/debug: Drop several unnecessary CFI annotations
Building a 32-bit kernel with CONFIG_X86_USE_3DNOW and CONFIG_EFI_STUB
leads to the following build error,
drivers/firmware/efi/libstub/lib.a(efi-stub-helper.o): In function `efi_relocate_kernel':
efi-stub-helper.c:(.text+0xda5): undefined reference to `_mmx_memcpy'
This is due to the fact that the EFI boot stub pulls in the 3DNow
optimized versions of the memcpy() prototype from
arch/x86/include/asm/string_32.h, even though the _mmx_memcpy()
implementation isn't available in the EFI stub.
For now, predicate CONFIG_EFI_STUB on !CONFIG_X86_USE_3DNOW. This is
most definitely a temporary fix. A complete solution will involve
selectively including kernel headers/symbols into the early-boot
execution environment of the EFI boot stub, i.e. something analogous to
the way that the _SETUP symbol is used.
Previous attempts have been made to fix this kind of problem, though
none seem to have ever been merged,
http://lkml.kernel.org/r/20120329104822.GA17233@x1.osrc.amd.com
Clearly, this problem has been around for a long time.
Reported-by: Ingo Molnar <mingo@kernel.org>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1407193939-27813-1-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Pull perf changes from Ingo Molnar:
"Kernel side changes:
- Consolidate the PMU interrupt-disabled code amongst architectures
(Vince Weaver)
- misc fixes
Tooling changes (new features, user visible changes):
- Add support for pagefault tracing in 'trace', please see multiple
examples in the changeset messages (Stanislav Fomichev).
- Add pagefault statistics in 'trace' (Stanislav Fomichev)
- Add header for columns in 'top' and 'report' TUI browsers (Jiri
Olsa)
- Add pagefault statistics in 'trace' (Stanislav Fomichev)
- Add IO mode into timechart command (Stanislav Fomichev)
- Fallback to syscalls:* when raw_syscalls:* is not available in the
perl and python perf scripts. (Daniel Bristot de Oliveira)
- Add --repeat global option to 'perf bench' to be used in benchmarks
such as the existing 'futex' one, that was modified to use it
instead of a local option. (Davidlohr Bueso)
- Fix fd -> pathname resolution in 'trace', be it using /proc or a
vfs_getname probe point. (Arnaldo Carvalho de Melo)
- Add suggestion of how to set perf_event_paranoid sysctl, to help
non-root users trying tools like 'trace' to get a working
environment. (Arnaldo Carvalho de Melo)
- Updates from trace-cmd for traceevent plugin_kvm plus args cleanup
(Steven Rostedt, Jan Kiszka)
- Support S/390 in 'perf kvm stat' (Alexander Yarygin)
Tooling infrastructure changes:
- Allow reserving a row for header purposes in the hists browser
(Arnaldo Carvalho de Melo)
- Various fixes and prep work related to supporting Intel PT (Adrian
Hunter)
- Introduce multiple debug variables control (Jiri Olsa)
- Add callchain and additional sample information for python scripts
(Joseph Schuchart)
- More prep work to support Intel PT: (Adrian Hunter)
- Polishing 'script' BTS output
- 'inject' can specify --kallsym
- VDSO is per machine, not a global var
- Expose data addr lookup functions previously private to 'script'
- Large mmap fixes in events processing
- Include standard stringify macros in power pc code (Sukadev
Bhattiprolu)
Tooling cleanups:
- Convert open coded equivalents to asprintf() (Andy Shevchenko)
- Remove needless reassignments in 'trace' (Arnaldo Carvalho de Melo)
- Cache the is_exit syscall test in 'trace) (Arnaldo Carvalho de
Melo)
- No need to reimplement err() in 'perf bench sched-messaging', drop
barf(). (Davidlohr Bueso).
- Remove ev_name argument from perf_evsel__hists_browse, can be
obtained from the other parameters. (Jiri Olsa)
Tooling fixes:
- Fix memory leak in the 'sched-messaging' perf bench test.
(Davidlohr Bueso)
- The -o and -n 'perf bench mem' options are mutually exclusive, emit
error when both are specified. (Davidlohr Bueso)
- Fix scrollbar refresh row index in the ui browser, problem exposed
now that headers will be added and will be allowed to be switched
on/off. (Jiri Olsa)
- Handle the num array type in python properly (Sebastian Andrzej
Siewior)
- Fix wrong condition for allocation failure (Jiri Olsa)
- Adjust callchain based on DWARF debug info on powerpc (Sukadev
Bhattiprolu)
- Fix a risk for doing free on uninitialized pointer in traceevent
lib (Rickard Strandqvist)
- Update attr test with PERF_FLAG_FD_CLOEXEC flag (Jiri Olsa)
- Enable close-on-exec flag on perf file descriptor (Yann Droneaud)
- Fix build on gcc 4.4.7 (Arnaldo Carvalho de Melo)
- Event ordering fixes (Jiri Olsa)"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (123 commits)
Revert "perf tools: Fix jump label always changing during tracing"
perf tools: Fix perf usage string leftover
perf: Check permission only for parent tracepoint event
perf record: Store PERF_RECORD_FINISHED_ROUND only for nonempty rounds
perf record: Always force PERF_RECORD_FINISHED_ROUND event
perf inject: Add --kallsyms parameter
perf tools: Expose 'addr' functions so they can be reused
perf session: Fix accounting of ordered samples queue
perf powerpc: Include util/util.h and remove stringify macros
perf tools: Fix build on gcc 4.4.7
perf tools: Add thread parameter to vdso__dso_findnew()
perf tools: Add dso__type()
perf tools: Separate the VDSO map name from the VDSO dso name
perf tools: Add vdso__new()
perf machine: Fix the lifetime of the VDSO temporary file
perf tools: Group VDSO global variables into a structure
perf session: Add ability to skip 4GiB or more
perf session: Add ability to 'skip' a non-piped event stream
perf tools: Pass machine to vdso__dso_findnew()
perf tools: Add dso__data_size()
...
Pull locking updates from Ingo Molnar:
"The main changes in this cycle are:
- big rtmutex and futex cleanup and robustification from Thomas
Gleixner
- mutex optimizations and refinements from Jason Low
- arch_mutex_cpu_relax() removal and related cleanups
- smaller lockdep tweaks"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
arch, locking: Ciao arch_mutex_cpu_relax()
locking/lockdep: Only ask for /proc/lock_stat output when available
locking/mutexes: Optimize mutex trylock slowpath
locking/mutexes: Try to acquire mutex only if it is unlocked
locking/mutexes: Delete the MUTEX_SHOW_NO_WAITER macro
locking/mutexes: Correct documentation on mutex optimistic spinning
rtmutex: Make the rtmutex tester depend on BROKEN
futex: Simplify futex_lock_pi_atomic() and make it more robust
futex: Split out the first waiter attachment from lookup_pi_state()
futex: Split out the waiter check from lookup_pi_state()
futex: Use futex_top_waiter() in lookup_pi_state()
futex: Make unlock_pi more robust
rtmutex: Avoid pointless requeueing in the deadlock detection chain walk
rtmutex: Cleanup deadlock detector debug logic
rtmutex: Confine deadlock logic to futex
rtmutex: Simplify remove_waiter()
rtmutex: Document pi chain walk
rtmutex: Clarify the boost/deboost part
rtmutex: No need to keep task ref for lock owner check
rtmutex: Simplify and document try_to_take_rtmutex()
...
few days.
MIPS and s390 have little going on this release; just bugfixes, some
small, some larger.
The highlights for x86 are nested VMX improvements (Jan Kiszka), optimizations
for old processor (up to Nehalem, by me and Bandan Das), and a lot of x86
emulator bugfixes (Nadav Amit).
Stephen Rothwell reported a trivial conflict with the tracing branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=UXxV
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM changes from Paolo Bonzini:
"These are the x86, MIPS and s390 changes; PPC and ARM will come in a
few days.
MIPS and s390 have little going on this release; just bugfixes, some
small, some larger.
The highlights for x86 are nested VMX improvements (Jan Kiszka),
optimizations for old processor (up to Nehalem, by me and Bandan Das),
and a lot of x86 emulator bugfixes (Nadav Amit).
Stephen Rothwell reported a trivial conflict with the tracing branch"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (104 commits)
x86/kvm: Resolve shadow warnings in macro expansion
KVM: s390: rework broken SIGP STOP interrupt handling
KVM: x86: always exit on EOIs for interrupts listed in the IOAPIC redir table
KVM: vmx: remove duplicate vmx_mpx_supported() prototype
KVM: s390: Fix memory leak on busy SIGP stop
x86/kvm: Resolve shadow warning from min macro
kvm: Resolve missing-field-initializers warnings
Replace NR_VMX_MSR with its definition
KVM: x86: Assertions to check no overrun in MSR lists
KVM: x86: set rflags.rf during fault injection
KVM: x86: Setting rflags.rf during rep-string emulation
KVM: x86: DR6/7.RTM cannot be written
KVM: nVMX: clean up nested_release_vmcs12 and code around it
KVM: nVMX: fix lifetime issues for vmcs02
KVM: x86: Defining missing x86 vectors
KVM: x86: emulator injects #DB when RFLAGS.RF is set
KVM: x86: Cleanup of rflags.rf cleaning
KVM: x86: Clear rflags.rf on emulated instructions
KVM: x86: popf emulation should not change RF
KVM: x86: Clearing rflags.rf upon skipped emulated instruction
...
to the ftrace function callback infrastructure. It's introducing a
way to allow different functions to call directly different trampolines
instead of all calling the same "mcount" one.
The only user of this for now is the function graph tracer, which always
had a different trampoline, but the function tracer trampoline was called
and did basically nothing, and then the function graph tracer trampoline
was called. The difference now, is that the function graph tracer
trampoline can be called directly if a function is only being traced by
the function graph trampoline. If function tracing is also happening on
the same function, the old way is still done.
The accounting for this takes up more memory when function graph tracing
is activated, as it needs to keep track of which functions it uses.
I have a new way that wont take as much memory, but it's not ready yet
for this merge window, and will have to wait for the next one.
Another big change was the removal of the ftrace_start/stop() calls that
were used by the suspend/resume code that stopped function tracing when
entering into suspend and resume paths. The stop of ftrace was done
because there was some function that would crash the system if one called
smp_processor_id()! The stop/start was a big hammer to solve the issue
at the time, which was when ftrace was first introduced into Linux.
Now ftrace has better infrastructure to debug such issues, and I found
the problem function and labeled it with "notrace" and function tracing
can now safely be activated all the way down into the guts of suspend
and resume.
Other changes include clean ups of uprobe code.
Clean up of the trace_seq() code.
And other various small fixes and clean ups to ftrace and tracing.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJT35zXAAoJEKQekfcNnQGuOz0H/38zqM0nLFhrgvz3EPk2UOjn
xqpX8qyb2V7TJZL+IqeXU2a5cQZl5ba0D4WtBGpxbTae3CJYiuQ87iKUNFoH0om5
FDpn80igb368k8V3qRdRsziKVCCf0XBd/NkHJXc0ZkfXGyzB2Ga4bBxALxp2gj9y
bnO+vKo6+tWYKG4hyQb4P3LRXUrK8/LWEsPr39cH2QH1Rdj69Lx9CgrCdUVJmwcb
Bj8hEiLXL/RYCFNn79A3wNTUvW0rG/AOIf4SLqXtasSRZ0ToaU0ZyDnrNv+0Ol47
rX8tSk+LfXchL9hpIvjCf1vlAYq3pO02favteR/jip3lx/dTjEDE4RJ9qtJzZ4Q=
=fwQY
-----END PGP SIGNATURE-----
Merge tag 'trace-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"This pull request has a lot of work done. The main thing is the
changes to the ftrace function callback infrastructure. It's
introducing a way to allow different functions to call directly
different trampolines instead of all calling the same "mcount" one.
The only user of this for now is the function graph tracer, which
always had a different trampoline, but the function tracer trampoline
was called and did basically nothing, and then the function graph
tracer trampoline was called. The difference now, is that the
function graph tracer trampoline can be called directly if a function
is only being traced by the function graph trampoline. If function
tracing is also happening on the same function, the old way is still
done.
The accounting for this takes up more memory when function graph
tracing is activated, as it needs to keep track of which functions it
uses. I have a new way that wont take as much memory, but it's not
ready yet for this merge window, and will have to wait for the next
one.
Another big change was the removal of the ftrace_start/stop() calls
that were used by the suspend/resume code that stopped function
tracing when entering into suspend and resume paths. The stop of
ftrace was done because there was some function that would crash the
system if one called smp_processor_id()! The stop/start was a big
hammer to solve the issue at the time, which was when ftrace was first
introduced into Linux. Now ftrace has better infrastructure to debug
such issues, and I found the problem function and labeled it with
"notrace" and function tracing can now safely be activated all the way
down into the guts of suspend and resume
Other changes include clean ups of uprobe code, clean up of the
trace_seq() code, and other various small fixes and clean ups to
ftrace and tracing"
* tag 'trace-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (57 commits)
ftrace: Add warning if tramp hash does not match nr_trampolines
ftrace: Fix trampoline hash update check on rec->flags
ring-buffer: Use rb_page_size() instead of open coded head_page size
ftrace: Rename ftrace_ops field from trampolines to nr_trampolines
tracing: Convert local function_graph functions to static
ftrace: Do not copy old hash when resetting
tracing: let user specify tracing_thresh after selecting function_graph
ring-buffer: Always run per-cpu ring buffer resize with schedule_work_on()
tracing: Remove function_trace_stop and HAVE_FUNCTION_TRACE_MCOUNT_TEST
s390/ftrace: remove check of obsolete variable function_trace_stop
arm64, ftrace: Remove check of obsolete variable function_trace_stop
Blackfin: ftrace: Remove check of obsolete variable function_trace_stop
metag: ftrace: Remove check of obsolete variable function_trace_stop
microblaze: ftrace: Remove check of obsolete variable function_trace_stop
MIPS: ftrace: Remove check of obsolete variable function_trace_stop
parisc: ftrace: Remove check of obsolete variable function_trace_stop
sh: ftrace: Remove check of obsolete variable function_trace_stop
sparc64,ftrace: Remove check of obsolete variable function_trace_stop
tile: ftrace: Remove check of obsolete variable function_trace_stop
ftrace: x86: Remove check of obsolete variable function_trace_stop
...
Pull percpu updates from Tejun Heo:
- Major reorganization of percpu header files which I think makes
things a lot more readable and logical than before.
- percpu-refcount is updated so that it requires explicit destruction
and can be reinitialized if necessary. This was pulled into the
block tree to replace the custom percpu refcnting implemented in
blk-mq.
- In the process, percpu and percpu-refcount got cleaned up a bit
* 'for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (21 commits)
percpu-refcount: implement percpu_ref_reinit() and percpu_ref_is_zero()
percpu-refcount: require percpu_ref to be exited explicitly
percpu-refcount: use unsigned long for pcpu_count pointer
percpu-refcount: add helpers for ->percpu_count accesses
percpu-refcount: one bit is enough for REF_STATUS
percpu-refcount, aio: use percpu_ref_cancel_init() in ioctx_alloc()
workqueue: stronger test in process_one_work()
workqueue: clear POOL_DISASSOCIATED in rebind_workers()
percpu: Use ALIGN macro instead of hand coding alignment calculation
percpu: invoke __verify_pcpu_ptr() from the generic part of accessors and operations
percpu: preffity percpu header files
percpu: use raw_cpu_*() to define __this_cpu_*()
percpu: reorder macros in percpu header files
percpu: move {raw|this}_cpu_*() definitions to include/linux/percpu-defs.h
percpu: move generic {raw|this}_cpu_*_N() definitions to include/asm-generic/percpu.h
percpu: only allow sized arch overrides for {raw|this}_cpu_*() ops
percpu: reorganize include/linux/percpu-defs.h
percpu: move accessors from include/linux/percpu.h to percpu-defs.h
percpu: include/asm-generic/percpu.h should contain only arch-overridable parts
percpu: introduce arch_raw_cpu_ptr()
...
Pull crypto update from Herbert Xu:
- CTR(AES) optimisation on x86_64 using "by8" AVX.
- arm64 support to ccp
- Intel QAT crypto driver
- Qualcomm crypto engine driver
- x86-64 assembly optimisation for 3DES
- CTR(3DES) speed test
- move FIPS panic from module.c so that it only triggers on crypto
modules
- SP800-90A Deterministic Random Bit Generator (drbg).
- more test vectors for ghash.
- tweak self tests to catch partial block bugs.
- misc fixes.
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (94 commits)
crypto: drbg - fix failure of generating multiple of 2**16 bytes
crypto: ccp - Do not sign extend input data to CCP
crypto: testmgr - add missing spaces to drbg error strings
crypto: atmel-tdes - Switch to managed version of kzalloc
crypto: atmel-sha - Switch to managed version of kzalloc
crypto: testmgr - use chunks smaller than algo block size in chunk tests
crypto: qat - Fixed SKU1 dev issue
crypto: qat - Use hweight for bit counting
crypto: qat - Updated print outputs
crypto: qat - change ae_num to ae_id
crypto: qat - change slice->regions to slice->region
crypto: qat - use min_t macro
crypto: qat - remove unnecessary parentheses
crypto: qat - remove unneeded header
crypto: qat - checkpatch blank lines
crypto: qat - remove unnecessary return codes
crypto: Resolve shadow warnings
crypto: ccp - Remove "select OF" from Kconfig
crypto: caam - fix DECO RSR polling
crypto: qce - Let 'DEV_QCE' depend on both HAS_DMA and HAS_IOMEM
...
I don't know if we really need 64 bits here but these variables are
declared as u64 and it can't hurt to cast this so we prevent any shift
wrapping.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Aubrey Li <aubrey.li@linux.intel.com>
Link: http://lkml.kernel.org/r/20140801082715.GE28869@mwanda
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
to indicate that this function is converting classic BPF into eBPF
and not related to sockets
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull x86 fix from Peter Anvin:
"A single fix to not invoke the espfix code on Xen PV, as it turns out
to oops the guest when invoked after all. This patch leaves some
amount of dead code, in particular unnecessary initialization of the
espfix stacks when they won't be used, but in the interest of keeping
the patch minimal that cleanup can wait for the next cycle"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86_64/entry/xen: Do not invoke espfix64 on Xen
Since checkin
411cf9ee29 x86, vsmp: Remove is_vsmp_box() from apic_is_clustered_box()
... is_vsmp_box() is only used in vsmp_64.c and does not have any
header file declaring it, so make it explicitly static.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Shai Fultheim <shai@scalemp.com>
Cc: Oren Twaig <oren@scalemp.com>
Link: http://lkml.kernel.org/r/1404036068-11674-1-git-send-email-oren@scalemp.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Removing a debug message for setting the identity map since it becomes
rather noisy after rework of the identity map code.
Signed-off-by: Matthew Rushton <mrushton@amazon.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
This has been run through Intel's LKP tests across a wide range
of modern sytems and workloads and it wasn't shown to make a
measurable performance difference positive or negative.
Now that we have some shiny new tracepoints, we can actually
figure out what the heck is going on.
During a kernel compile, 60% of the flush_tlb_mm_range() calls
are for a single page. It breaks down like this:
size percent percent<=
V V V
GLOBAL: 2.20% 2.20% avg cycles: 2283
1: 56.92% 59.12% avg cycles: 1276
2: 13.78% 72.90% avg cycles: 1505
3: 8.26% 81.16% avg cycles: 1880
4: 7.41% 88.58% avg cycles: 2447
5: 1.73% 90.31% avg cycles: 2358
6: 1.32% 91.63% avg cycles: 2563
7: 1.14% 92.77% avg cycles: 2862
8: 0.62% 93.39% avg cycles: 3542
9: 0.08% 93.47% avg cycles: 3289
10: 0.43% 93.90% avg cycles: 3570
11: 0.20% 94.10% avg cycles: 3767
12: 0.08% 94.18% avg cycles: 3996
13: 0.03% 94.20% avg cycles: 4077
14: 0.02% 94.23% avg cycles: 4836
15: 0.04% 94.26% avg cycles: 5699
16: 0.06% 94.32% avg cycles: 5041
17: 0.57% 94.89% avg cycles: 5473
18: 0.02% 94.91% avg cycles: 5396
19: 0.03% 94.95% avg cycles: 5296
20: 0.02% 94.96% avg cycles: 6749
21: 0.18% 95.14% avg cycles: 6225
22: 0.01% 95.15% avg cycles: 6393
23: 0.01% 95.16% avg cycles: 6861
24: 0.12% 95.28% avg cycles: 6912
25: 0.05% 95.32% avg cycles: 7190
26: 0.01% 95.33% avg cycles: 7793
27: 0.01% 95.34% avg cycles: 7833
28: 0.01% 95.35% avg cycles: 8253
29: 0.08% 95.42% avg cycles: 8024
30: 0.03% 95.45% avg cycles: 9670
31: 0.01% 95.46% avg cycles: 8949
32: 0.01% 95.46% avg cycles: 9350
33: 3.11% 98.57% avg cycles: 8534
34: 0.02% 98.60% avg cycles: 10977
35: 0.02% 98.62% avg cycles: 11400
We get in to dimishing returns pretty quickly. On pre-IvyBridge
CPUs, we used to set the limit at 8 pages, and it was set at 128
on IvyBrige. That 128 number looks pretty silly considering that
less than 0.5% of the flushes are that large.
The previous code tried to size this number based on the size of
the TLB. Good idea, but it's error-prone, needs maintenance
(which it didn't get up to now), and probably would not matter in
practice much.
Settting it to 33 means that we cover the mallopt
M_TRIM_THRESHOLD, which is the most universally common size to do
flushes.
That's the short version. Here's the long one for why I chose 33:
1. These numbers have a constant bias in the timestamps from the
tracing. Probably counts for a couple hundred cycles in each of
these tests, but it should be fairly _even_ across all of them.
The smallest delta between the tracepoints I have ever seen is
335 cycles. This is one reason the cycles/page cost goes down in
general as the flushes get larger. The true cost is nearer to
100 cycles.
2. A full flush is more expensive than a single invlpg, but not
by much (single percentages).
3. A dtlb miss is 17.1ns (~45 cycles) and a itlb miss is 13.0ns
(~34 cycles). At those rates, refilling the 512-entry dTLB takes
22,000 cycles.
4. 22,000 cycles is approximately the equivalent of doing 85
invlpg operations. But, the odds are that the TLB can
actually be filled up faster than that because TLB misses that
are close in time also tend to leverage the same caches.
6. ~98% of flushes are <=33 pages. There are a lot of flushes of
33 pages, probably because libc's M_TRIM_THRESHOLD is set to
128k (32 pages)
7. I've found no consistent data to support changing the IvyBridge
vs. SandyBridge tunable by a factor of 16
I used the performance counters on this hardware (IvyBridge i5-3320M)
to figure out the tlb miss costs:
ocperf.py stat -e dtlb_load_misses.walk_duration,dtlb_load_misses.walk_completed,dtlb_store_misses.walk_duration,dtlb_store_misses.walk_completed,itlb_misses.walk_duration,itlb_misses.walk_completed,itlb.itlb_flush
7,720,030,970 dtlb_load_misses_walk_duration [57.13%]
169,856,353 dtlb_load_misses_walk_completed [57.15%]
708,832,859 dtlb_store_misses_walk_duration [57.17%]
19,346,823 dtlb_store_misses_walk_completed [57.17%]
2,779,687,402 itlb_misses_walk_duration [57.15%]
82,241,148 itlb_misses_walk_completed [57.13%]
770,717 itlb_itlb_flush [57.11%]
Show that a dtlb miss is 17.1ns (~45 cycles) and a itlb miss is 13.0ns
(~34 cycles). At those rates, refilling the 512-entry dTLB takes
22,000 cycles. On a SandyBridge system with more cores and larger
caches, those are dtlb=13.4ns and itlb=9.5ns.
cat perf.stat.txt | perl -pe 's/,//g'
| awk '/itlb_misses_walk_duration/ { icyc+=$1 }
/itlb_misses_walk_completed/ { imiss+=$1 }
/dtlb_.*_walk_duration/ { dcyc+=$1 }
/dtlb_.*.*completed/ { dmiss+=$1 }
END {print "itlb cyc/miss: ", icyc/imiss, " dtlb cyc/miss: ", dcyc/dmiss, " ----- ", icyc,imiss, dcyc,dmiss }
On Westmere CPUs, the counters to use are: itlb_flush,itlb_misses.walk_cycles,itlb_misses.any,dtlb_misses.walk_cycles,dtlb_misses.any
The assumptions that this code went in under:
https://lkml.org/lkml/2012/6/12/119 say that a flush and a refill are
about 100ns. Being generous, that is over by a factor of 6 on the
refill side, although it is fairly close on the cost of an invlpg.
An increase of a single invlpg operation seems to lengthen the flush
range operation by about 200 cycles. Here is one example of the data
collected for flushing 10 and 11 pages (full data are below):
10: 0.43% 93.90% avg cycles: 3570 cycles/page: 357 samples: 4714
11: 0.20% 94.10% avg cycles: 3767 cycles/page: 342 samples: 2145
How to generate this table:
echo 10000 > /sys/kernel/debug/tracing/buffer_size_kb
echo x86-tsc > /sys/kernel/debug/tracing/trace_clock
echo 'reason != 0' > /sys/kernel/debug/tracing/events/tlb/tlb_flush/filter
echo 1 > /sys/kernel/debug/tracing/events/tlb/tlb_flush/enable
Pipe the trace output in to this script:
http://sr71.net/~dave/intel/201402-tlb/trace-time-diff-process.pl.txt
Note that these data were gathered with the invlpg threshold set to
150 pages. Only data points with >=50 of samples were printed:
Flush % of %<=
in flush this
pages es size
------------------------------------------------------------------------------
-1: 2.20% 2.20% avg cycles: 2283 cycles/page: xxxx samples: 23960
1: 56.92% 59.12% avg cycles: 1276 cycles/page: 1276 samples: 620895
2: 13.78% 72.90% avg cycles: 1505 cycles/page: 752 samples: 150335
3: 8.26% 81.16% avg cycles: 1880 cycles/page: 626 samples: 90131
4: 7.41% 88.58% avg cycles: 2447 cycles/page: 611 samples: 80877
5: 1.73% 90.31% avg cycles: 2358 cycles/page: 471 samples: 18885
6: 1.32% 91.63% avg cycles: 2563 cycles/page: 427 samples: 14397
7: 1.14% 92.77% avg cycles: 2862 cycles/page: 408 samples: 12441
8: 0.62% 93.39% avg cycles: 3542 cycles/page: 442 samples: 6721
9: 0.08% 93.47% avg cycles: 3289 cycles/page: 365 samples: 917
10: 0.43% 93.90% avg cycles: 3570 cycles/page: 357 samples: 4714
11: 0.20% 94.10% avg cycles: 3767 cycles/page: 342 samples: 2145
12: 0.08% 94.18% avg cycles: 3996 cycles/page: 333 samples: 864
13: 0.03% 94.20% avg cycles: 4077 cycles/page: 313 samples: 289
14: 0.02% 94.23% avg cycles: 4836 cycles/page: 345 samples: 236
15: 0.04% 94.26% avg cycles: 5699 cycles/page: 379 samples: 390
16: 0.06% 94.32% avg cycles: 5041 cycles/page: 315 samples: 643
17: 0.57% 94.89% avg cycles: 5473 cycles/page: 321 samples: 6229
18: 0.02% 94.91% avg cycles: 5396 cycles/page: 299 samples: 224
19: 0.03% 94.95% avg cycles: 5296 cycles/page: 278 samples: 367
20: 0.02% 94.96% avg cycles: 6749 cycles/page: 337 samples: 185
21: 0.18% 95.14% avg cycles: 6225 cycles/page: 296 samples: 1964
22: 0.01% 95.15% avg cycles: 6393 cycles/page: 290 samples: 83
23: 0.01% 95.16% avg cycles: 6861 cycles/page: 298 samples: 61
24: 0.12% 95.28% avg cycles: 6912 cycles/page: 288 samples: 1307
25: 0.05% 95.32% avg cycles: 7190 cycles/page: 287 samples: 533
26: 0.01% 95.33% avg cycles: 7793 cycles/page: 299 samples: 94
27: 0.01% 95.34% avg cycles: 7833 cycles/page: 290 samples: 66
28: 0.01% 95.35% avg cycles: 8253 cycles/page: 294 samples: 73
29: 0.08% 95.42% avg cycles: 8024 cycles/page: 276 samples: 846
30: 0.03% 95.45% avg cycles: 9670 cycles/page: 322 samples: 296
31: 0.01% 95.46% avg cycles: 8949 cycles/page: 288 samples: 79
32: 0.01% 95.46% avg cycles: 9350 cycles/page: 292 samples: 60
33: 3.11% 98.57% avg cycles: 8534 cycles/page: 258 samples: 33936
34: 0.02% 98.60% avg cycles: 10977 cycles/page: 322 samples: 268
35: 0.02% 98.62% avg cycles: 11400 cycles/page: 325 samples: 177
36: 0.01% 98.63% avg cycles: 11504 cycles/page: 319 samples: 161
37: 0.02% 98.65% avg cycles: 11596 cycles/page: 313 samples: 182
38: 0.02% 98.66% avg cycles: 11850 cycles/page: 311 samples: 195
39: 0.01% 98.68% avg cycles: 12158 cycles/page: 311 samples: 128
40: 0.01% 98.68% avg cycles: 11626 cycles/page: 290 samples: 78
41: 0.04% 98.73% avg cycles: 11435 cycles/page: 278 samples: 477
42: 0.01% 98.73% avg cycles: 12571 cycles/page: 299 samples: 74
43: 0.01% 98.74% avg cycles: 12562 cycles/page: 292 samples: 78
44: 0.01% 98.75% avg cycles: 12991 cycles/page: 295 samples: 108
45: 0.01% 98.76% avg cycles: 13169 cycles/page: 292 samples: 78
46: 0.02% 98.78% avg cycles: 12891 cycles/page: 280 samples: 261
47: 0.01% 98.79% avg cycles: 13099 cycles/page: 278 samples: 67
48: 0.01% 98.80% avg cycles: 13851 cycles/page: 288 samples: 77
49: 0.01% 98.80% avg cycles: 13749 cycles/page: 280 samples: 66
50: 0.01% 98.81% avg cycles: 13949 cycles/page: 278 samples: 73
52: 0.00% 98.82% avg cycles: 14243 cycles/page: 273 samples: 52
54: 0.01% 98.83% avg cycles: 15312 cycles/page: 283 samples: 87
55: 0.01% 98.84% avg cycles: 15197 cycles/page: 276 samples: 109
56: 0.02% 98.86% avg cycles: 15234 cycles/page: 272 samples: 208
57: 0.00% 98.86% avg cycles: 14888 cycles/page: 261 samples: 53
58: 0.01% 98.87% avg cycles: 15037 cycles/page: 259 samples: 59
59: 0.01% 98.87% avg cycles: 15752 cycles/page: 266 samples: 63
62: 0.00% 98.89% avg cycles: 16222 cycles/page: 261 samples: 54
64: 0.02% 98.91% avg cycles: 17179 cycles/page: 268 samples: 248
65: 0.12% 99.03% avg cycles: 18762 cycles/page: 288 samples: 1324
85: 0.00% 99.10% avg cycles: 21649 cycles/page: 254 samples: 50
127: 0.01% 99.18% avg cycles: 32397 cycles/page: 255 samples: 75
128: 0.13% 99.31% avg cycles: 31711 cycles/page: 247 samples: 1466
129: 0.18% 99.49% avg cycles: 33017 cycles/page: 255 samples: 1927
181: 0.33% 99.84% avg cycles: 2489 cycles/page: 13 samples: 3547
256: 0.05% 99.91% avg cycles: 2305 cycles/page: 9 samples: 550
512: 0.03% 99.95% avg cycles: 2133 cycles/page: 4 samples: 304
1512: 0.01% 99.99% avg cycles: 3038 cycles/page: 2 samples: 65
Here are the tlb counters during a 10-second slice of a kernel compile
for a SandyBridge system. It's better than IvyBridge, but probably
due to the larger caches since this was one of the 'X' extreme parts.
10,873,007,282 dtlb_load_misses_walk_duration
250,711,333 dtlb_load_misses_walk_completed
1,212,395,865 dtlb_store_misses_walk_duration
31,615,772 dtlb_store_misses_walk_completed
5,091,010,274 itlb_misses_walk_duration
163,193,511 itlb_misses_walk_completed
1,321,980 itlb_itlb_flush
10.008045158 seconds time elapsed
# cat perf.stat.1392743721.txt | perl -pe 's/,//g' | awk '/itlb_misses_walk_duration/ { icyc+=$1 } /itlb_misses_walk_completed/ { imiss+=$1 } /dtlb_.*_walk_duration/ { dcyc+=$1 } /dtlb_.*.*completed/ { dmiss+=$1 } END {print "itlb cyc/miss: ", icyc/imiss/3.3, " dtlb cyc/miss: ", dcyc/dmiss/3.3, " ----- ", icyc,imiss, dcyc,dmiss }'
itlb ns/miss: 9.45338 dtlb ns/miss: 12.9716
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: http://lkml.kernel.org/r/20140731154103.10C1115E@viggo.jf.intel.com
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Most of the logic here is in the documentation file. Please take
a look at it.
I know we've come full-circle here back to a tunable, but this
new one is *WAY* simpler. I challenge anyone to describe in one
sentence how the old one worked. Here's the way the new one
works:
If we are flushing more pages than the ceiling, we use
the full flush, otherwise we use per-page flushes.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: http://lkml.kernel.org/r/20140731154101.12B52CAF@viggo.jf.intel.com
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
We don't have any good way to figure out what kinds of flushes
are being attempted. Right now, we can try to use the vm
counters, but those only tell us what we actually did with the
hardware (one-by-one vs full) and don't tell us what was actually
_requested_.
This allows us to select out "interesting" TLB flushes that we
might want to optimize (like the ranged ones) and ignore the ones
that we have very little control over (the ones at context
switch).
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: http://lkml.kernel.org/r/20140731154059.4C96CBA5@viggo.jf.intel.com
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
There are currently three paths through the remote flush code:
1. full invalidation
2. single page invalidation using invlpg
3. ranged invalidation using invlpg
This takes 2 and 3 and combines them in to a single path by
making the single-page one just be the start and end be start
plus a single page. This makes placement of our tracepoint easier.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: http://lkml.kernel.org/r/20140731154058.E0F90408@viggo.jf.intel.com
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
If we take the
if (end == TLB_FLUSH_ALL || vmflag & VM_HUGETLB) {
local_flush_tlb();
goto out;
}
path out of flush_tlb_mm_range(), we will have flushed the tlb,
but not incremented NR_TLB_LOCAL_FLUSH_ALL. This unifies the
way out of the function so that we always take a single path when
doing a full tlb flush.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: http://lkml.kernel.org/r/20140731154056.FF763B76@viggo.jf.intel.com
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
I think the flush_tlb_mm_range() code that tries to tune the
flush sizes based on the CPU needs to get ripped out for
several reasons:
1. It is obviously buggy. It uses mm->total_vm to judge the
task's footprint in the TLB. It should certainly be using
some measure of RSS, *NOT* ->total_vm since only resident
memory can populate the TLB.
2. Haswell, and several other CPUs are missing from the
intel_tlb_flushall_shift_set() function. Thus, it has been
demonstrated to bitrot quickly in practice.
3. It is plain wrong in my vm:
[ 0.037444] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
[ 0.037444] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0
[ 0.037444] tlb_flushall_shift: 6
Which leads to it to never use invlpg.
4. The assumptions about TLB refill costs are wrong:
http://lkml.kernel.org/r/1337782555-8088-3-git-send-email-alex.shi@intel.com
(more on this in later patches)
5. I can not reproduce the original data: https://lkml.org/lkml/2012/5/17/59
I believe the sample times were too short. Running the
benchmark in a loop yields times that vary quite a bit.
Note that this leaves us with a static ceiling of 1 page. This
is a conservative, dumb setting, and will be revised in a later
patch.
This also removes the code which attempts to predict whether we
are flushing data or instructions. We expect instruction flushes
to be relatively rare and not worth tuning for explicitly.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: http://lkml.kernel.org/r/20140731154055.ABC88E89@viggo.jf.intel.com
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The
if (cpumask_any_but(mm_cpumask(mm), smp_processor_id()) < nr_cpu_ids)
line of code is not exactly the easiest to audit, especially when
it ends up at two different indentation levels. This eliminates
one of the the copy-n-paste versions. It also gives us a unified
exit point for each path through this function. We need this in
a minute for our tracepoint.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: http://lkml.kernel.org/r/20140731154054.44F1CDDC@viggo.jf.intel.com
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Since commit b5660ba76b ("x86, platforms: Remove NUMAQ") removed NUMAQ,
the mps_oem_check() apic callback has been obsolete. Remove it.
This allows generic_mps_oem_check() to be removed as well.
Signed-off-by: David Rientjes <rientjes@google.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1407302349390.17503@chino.kir.corp.google.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The trampoline_phys_{high,low} members of struct apic are always
initialized to DEFAULT_TRAMPOLINE_PHYS_HIGH and TRAMPOLINE_PHYS_LOW,
respectively. Hardwire the constants and remove the unneeded members.
Signed-off-by: David Rientjes <rientjes@google.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1407302348330.17503@chino.kir.corp.google.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Resolve shadow warnings that appear in W=2 builds. Instead of
using ret to hold the return pointer, save the length in a new
variable saved_len and compute the pointer on exit. This also
resolves a very technical error, in that ret was declared as
a const char *, when it really was a char * const.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The primary dependency is that GHES uses the x86 NMI for hardware
error notification and MCE for memory error handling. These patches
remove that dependency.
Other APEI features such as error reporting via external IRQ, error
serialization, or error injection, do not require changes to use them
on non-x86 architectures.
The following patch set eliminates the APEI Kconfig x86 dependency
by making these changes:
- treat NMI notification as GHES architecture - HAVE_ACPI_APEI_NMI
- group and wrap around #ifdef CONFIG_HAVE_ACPI_APEI_NMI code which
is used only for NMI path
- identify architectural boxes and abstract it accordingly (tlb flush and MCE)
- rework ioremap for both IRQ and NMI context
NMI code is kept in ghes.c file since NMI and IRQ context are tightly coupled.
Note, these patches introduce no functional changes for x86. The NMI notification
feature is hard selected for x86. Architectures that want to use this
feature should also provide NMI code infrastructure.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nYdd
-----END PGP SIGNATURE-----
Merge tag 'please-pull-apei' into x86/ras
APEI is currently implemented so that it depends on x86 hardware.
The primary dependency is that GHES uses the x86 NMI for hardware
error notification and MCE for memory error handling. These patches
remove that dependency.
Other APEI features such as error reporting via external IRQ, error
serialization, or error injection, do not require changes to use them
on non-x86 architectures.
The following patch set eliminates the APEI Kconfig x86 dependency
by making these changes:
- treat NMI notification as GHES architecture - HAVE_ACPI_APEI_NMI
- group and wrap around #ifdef CONFIG_HAVE_ACPI_APEI_NMI code which
is used only for NMI path
- identify architectural boxes and abstract it accordingly (tlb flush and MCE)
- rework ioremap for both IRQ and NMI context
NMI code is kept in ghes.c file since NMI and IRQ context are tightly coupled.
Note, these patches introduce no functional changes for x86. The NMI notification
feature is hard selected for x86. Architectures that want to use this
feature should also provide NMI code infrastructure.
often during boot with Ubuntu 14.04 PV guests.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJT2PhgAAoJEFxbo/MsZsTRlzIH/1HjbkGZmRlOj5wcrYlWCUJ/
DGLBHc76so52xd9oP8COT5tuSVP6/usPPLFaOmVZ7fMiOpoyz9d3lc0g56otw3gJ
tTUFTyW0EoFtvmIl50OMC726p9azETjA3P2XJkV/D3GhBGGqgrP5uR+mRvisvq3y
eGZEx1UIHv1jov47TBFR1NcckXBWw+6J9m34y9h6an9VNDCuuGwYZ8dfGAFsLrVb
lGLTmgQQmyk4SexVINfOwL40KkVDVEq+X74HcPviyNHEIy66xLzMtKpL+Sf4xeuv
VG3JhqAUGuRGGK48rrbpxhBbpxGp35O9RV68YrGssxfuTejSYduw5zTzzt30QIA=
=cr8X
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.16-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen fix from David Vrabel:
"Fix BUG when trying to expand the grant table. This seems to occur
often during boot with Ubuntu 14.04 PV guests"
* tag 'stable/for-linus-3.16-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: safely map and unmap grant frames when in atomic context
Remove a prototype which was added by both 93c4adc7af and 36be0b9deb.
Signed-off-by: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
arch_gnttab_map_frames() and arch_gnttab_unmap_frames() are called in
atomic context but were calling alloc_vm_area() which might sleep.
Also, if a driver attempts to allocate a grant ref from an interrupt
and the table needs expanding, then the CPU may already by in lazy MMU
mode and apply_to_page_range() will BUG when it tries to re-enable
lazy MMU mode.
These two functions are only used in PV guests.
Introduce arch_gnttab_init() to allocates the virtual address space in
advance.
Avoid the use of apply_to_page_range() by using saving and using the
array of PTE addresses from the alloc_vm_area() call (which ensures
that the required page tables are pre-allocated).
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This moves the espfix64 logic into native_iret. To make this work,
it gets rid of the native patch for INTERRUPT_RETURN:
INTERRUPT_RETURN on native kernels is now 'jmp native_iret'.
This changes the 16-bit SS behavior on Xen from OOPSing to leaking
some bits of the Xen hypervisor's RSP (I think).
[ hpa: this is a nonzero cost on native, but probably not enough to
measure. Xen needs to fix this in their own code, probably doing
something equivalent to espfix64. ]
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/7b8f1d8ef6597cb16ae004a43c56980a7de3cf94.1406129132.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
In preparation to make the check_extension function available to VM scope
we add a struct kvm * argument to the function header and rename the function
accordingly. It will still be called from the /dev/kvm fd, but with a NULL
argument for struct kvm *.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJT1VYNAAoJEHm+PkMAQRiGQJwIAKSYp1Uqz5O/e5r0V1TlZKT4
1B4Njopl57PwSrJQWcGEuH2yHyM896vfPO4L6BJIOfyWzh8kwpQqclDt6uhXoF/v
OsO1zb/7/j+n/pDZsePqP9AyIgErsHEBgUbhecDqzjN++ITPcZjQ6TIMPglZaumN
jFAdAZuAaEwqAk8jqN2wlm689Fh9MuUEarHXbXLCqu5RgLrWhFGhp/cTWY62aqnZ
XfEeQ9KtpRZmlR/IYjerbb1eRH7ZdJsZ88WngLX9dj/JdNxHWBkWQBXGAusXk5Fk
y6LsIV3TjyBdrRKJ1Ifyg/2EIXHNBs8HxTFGXpjtp2HPuMLDxZOWOWikb9URtNg=
=Fjf4
-----END PGP SIGNATURE-----
Merge tag 'v3.16-rc7' into perf/core, to merge in the latest fixes before applying new changes
Signed-off-by: Ingo Molnar <mingo@kernel.org>
* acpi-headers:
ACPI: Add support to force header inclusion rules for <acpi/acpi.h>.
ACPI / SFI: Fix wrong <acpi/acpi.h> inclusion in SFI/ACPI wrapper - table definitions.
ACPICA: Linux: Allow ACPICA inclusion for CONFIG_ACPI=n builds.
ACPICA: Linux: Add support to exclude <asm/acenv.h> inclusion.
ACPICA: Linux: Add stub implementation of ACPICA 64-bit mathematics.
ACPICA: Linux: Add stub support for Linux specific variables and functions.
Pull perf fixes from Thomas Gleixner:
"A bunch of fixes for perf and kprobes:
- revert a commit that caused a perf group regression
- silence dmesg spam
- fix kprobe probing errors on ia64 and ppc64
- filter kprobe faults from userspace
- lockdep fix for perf exit path
- prevent perf #GP in KVM guest
- correct perf event and filters"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kprobes: Fix "Failed to find blacklist" probing errors on ia64 and ppc64
kprobes/x86: Don't try to resolve kprobe faults from userspace
perf/x86/intel: Avoid spamming kernel log for BTS buffer failure
perf/x86/intel: Protect LBR and extra_regs against KVM lying
perf: Fix lockdep warning on process exit
perf/x86/intel/uncore: Fix SNB-EP/IVT Cbox filter mappings
perf/x86/intel: Use proper dTLB-load-misses event on IvyBridge
perf: Revert ("perf: Always destroy groups on exit")
Pull x86 fixes from Peter Anvin:
"A couple of crash fixes, plus a fix that on 32 bits would cause a
missing -ENOSYS for nonexistent system calls"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, cpu: Fix cache topology for early P4-SMT
x86_32, entry: Store badsys error code in %eax
x86, MCE: Robustify mcheck_init_device
This commit in Linux 3.6:
commit c767a54ba0
Author: Joe Perches <joe@perches.com>
Date: Mon May 21 19:50:07 2012 -0700
x86/debug: Add KERN_<LEVEL> to bare printks, convert printks to pr_<level>
caused warn_bad_vsyscall to output garbage in the middle of the
line. Revert the bad part of it.
The printk in question isn't actually bare; the level is "%s".
The bug this fixes is purely cosmetic; backports are optional.
Cc: <stable@vger.kernel.org> # v3.6+
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/03eac1f24110bbe496ecc12a4df467e0d88466d4.1406330947.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The VVAR area can, obviously, be read; that is kind of the point.
AFAIK this has no effect whatsoever unless x86 suddenly turns into a
nommu architecture. Nonetheless, not setting it is suspicious.
Reported-by: Nathan Lynch <Nathan_Lynch@mentor.com>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/e4c8bf4bc2725bda22c4a4b7d0c82adcd8f8d9b8.1406330779.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Add the following interfaces to exposes PMC device state and sleep
state residency via debugfs:
/sys/kernel/debugfs/pmc_atom/dev_state
/sys/kernel/debugfs/pmc_atom/sleep_state
Signed-off-by: Aubrey Li <aubrey.li@linux.intel.com>
Link: http://lkml.kernel.org/r/53B0FF59.8000600@linux.intel.com
Signed-off-by: Kasagar, Srinidhi <srinidhi.kasagar@intel.com>
Reviewed-by: Rudramuni, Vishwesh M <vishwesh.m.rudramuni@intel.com>
Reviewed-by: Joe Perches <joe@perches.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Disable PMC S0IX_WAKE_EN events coming from LPC block(unused) and
also from GPIO_SUS ored dedicated IRQs (must be disabled as per PMC
programming rule), GPIOSCORE ored dedicated IRQs (must be disabled
as per PMC programming rule), GPIO_SUS shared IRQ (not necessary
since the IOAPIC_DS wake event will still work), GPIO_SCORE shared
IRQ (not necessary since the IOAPIC_DS wake event will still work).
Signed-off-by: Aubrey Li <aubrey.li@linux.intel.com>
Link: http://lkml.kernel.org/r/53B0FF22.5080403@linux.intel.com
Signed-off-by: Olivier Leveque <olivier.leveque@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The Power Management Controller (PMC) controls many of the power
management features present in the Atom SoC. This driver provides
a native power off function via PMC PCI IO port.
On some ACPI hardware-reduced platforms(e.g. ASUS-T100), ACPI sleep
registers are not valid so that (*pm_power_off)() is not hooked by
acpi_power_off(). The power off function in this driver is installed
only when pm_power_off is NULL.
Signed-off-by: Aubrey Li <aubrey.li@linux.intel.com>
Link: http://lkml.kernel.org/r/53B0FEEA.3010805@linux.intel.com
Signed-off-by: Lejun Zhu <lejun.zhu@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Resolve a shadow warning generated in W=2 builds by the nested
use of the min macro by instead using the min3 macro for the
minimum of 3 values.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
eBPF is used by socket filtering, seccomp and soon by tracing and
exposed to userspace, therefore 'sock_filter_int' name is not accurate.
Rename it to 'bpf_insn'
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix was necessary after
9c15a24b03 ("x86/mce: Improve mcheck_init_device() error handling")
went in. What this patch did was, among others, check the return value
of misc_register and exit early if it encountered an error. Original
code sloppily didn't do that.
However,
cef12ee52b ("xen/mce: Add mcelog support for Xen platform")
made it so that xen's init routine xen_late_init_mcelog runs first. This
was needed for the xen mcelog device which is supposed to be independent
from the baremetal one.
Initially it was reported that misc_register() fails often on xen and
that's why it needed fixing. However, it is *supposed* to fail by
design, when running in dom0 so that the xen mcelog device file gets
registered first.
And *then* you need the notifier *not* unregistered on the error path so
that the timer does get deleted properly in the CPU hotplug notifier.
Btw, this fix is needed also on baremetal in the unlikely event that
misc_register(&mce_chrdev_device) fails there too.
I was unsure whether to rush it in now and decided to delay it to 3.17.
However, xen people wanted it promoted as it breaks xen when doing cpu
hotplug there. So, after a bit of simmering in tip/master for initial
smoke testing, let's move it to 3.16. It fixes a semi-regression which
got introduced in 3.16 so no need for stable tagging.
tip/x86/ras contains that exact same commit but we can't remove it
there as it is not the last one. It won't cause any merge issues, as I
confirmed locally but I should state here the special situation of this
one fix explicitly anyway.
Thanks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z/P/
-----END PGP SIGNATURE-----
x86: Merge tag 'ras_urgent' into x86/urgent
Promote one fix for 3.16
This fix was necessary after
9c15a24b03 ("x86/mce: Improve mcheck_init_device() error handling")
went in. What this patch did was, among others, check the return value
of misc_register and exit early if it encountered an error. Original
code sloppily didn't do that.
However,
cef12ee52b ("xen/mce: Add mcelog support for Xen platform")
made it so that xen's init routine xen_late_init_mcelog runs first. This
was needed for the xen mcelog device which is supposed to be independent
from the baremetal one.
Initially it was reported that misc_register() fails often on xen and
that's why it needed fixing. However, it is *supposed* to fail by
design, when running in dom0 so that the xen mcelog device file gets
registered first.
And *then* you need the notifier *not* unregistered on the error path so
that the timer does get deleted properly in the CPU hotplug notifier.
Btw, this fix is needed also on baremetal in the unlikely event that
misc_register(&mce_chrdev_device) fails there too.
I was unsure whether to rush it in now and decided to delay it to 3.17.
However, xen people wanted it promoted as it breaks xen when doing cpu
hotplug there. So, after a bit of simmering in tip/master for initial
smoke testing, let's move it to 3.16. It fixes a semi-regression which
got introduced in 3.16 so no need for stable tagging.
tip/x86/ras contains that exact same commit but we can't remove it
there as it is not the last one. It won't cause any merge issues, as I
confirmed locally but I should state here the special situation of this
one fix explicitly anyway.
Thanks.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Using ARRAY_SIZE directly makes it easier to read the code. While touching
the code, replace the division by a multiplication in the recently added
BUILD_BUG_ON.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently there is no check whether shared MSRs list overrun the allocated size
which can results in bugs. In addition there is no check that vmx->guest_msrs
has sufficient space to accommodate all the VMX msrs. This patch adds the
assertions.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
x86 does not automatically set rflags.rf during event injection. This patch
does partial job, setting rflags.rf upon fault injection. It does not handle
the setting of RF upon interrupt injection on rep-string instruction.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch updates RF for rep-string emulation. The flag is set upon the first
iteration, and cleared after the last (if emulated). It is intended to make
sure that if a trap (in future data/io #DB emulation) or interrupt is delivered
to the guest during the rep-string instruction, RF will be set correctly. RF
affects whether instruction breakpoint in the guest is masked.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The members of the new struct are the required ones for the new NMI
safe accessor to clcok monotonic. In order to reuse the existing
timekeeping code and to make the update of the fast NMI safe
timekeepers a simple memcpy use the struct for the timekeeper as well
and convert all users.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
cycle_last was added to the clocksource to support the TSC
validation. We moved that to the core code, so we can get rid of the
extra copy.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The only user of the cycle_last validation is the x86 TSC. In order to
provide NMI safe accessor functions for clock monotonic and
monotonic_raw we need to do that in the core.
We can't do the TSC specific
if (now < cycle_last)
now = cycle_last;
for the other wrapping around clocksources, but TSC has
CLOCKSOURCE_MASK(64) which actually does not mask out anything so if
now is less than cycle_last the subtraction will give a negative
result. So we can check for that in clocksource_delta() and return 0
for that case.
Implement and enable it for x86
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Convert the relevant base data right away to nanoseconds instead of
doing the conversion on every readout. Reduces text size by 160 bytes.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Use the new nanoseconds based interface and get rid of the timespec
conversion dance.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The non-scalar ktime_t implementation is basically a timespec
which has to be changed to support dates past 2038 on 32bit
systems.
This patch removes the non-scalar ktime_t implementation, forcing
the scalar s64 nanosecond version on all architectures.
This may have additional performance overhead on some 32bit
systems when converting between ktime_t and timespec structures,
however the majority of 32bit systems (arm and i386) were already
using scalar ktime_t, so no performance regressions will be seen
on those platforms.
On affected platforms, I'm open to finding optimizations, including
avoiding converting to timespecs where possible.
[ tglx: We can now cleanup the ktime_t.tv64 mess, but thats a
different issue and we can throw a coccinelle script at it ]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
P4 systems with cpuid level < 4 can have SMT, but the cache topology
description available (cpuid2) does not include SMP information.
Now we know that SMT shares all cache levels, and therefore we can
mark all available cache levels as shared.
We do this by setting cpu_llc_id to ->phys_proc_id, since that's
the same for each SMT thread. We can do this unconditional since if
there's no SMT its still true, the one CPU shares cache with only
itself.
This fixes a problem where such CPUs report an incorrect LLC CPU mask.
This in turn fixes a crash in the scheduler where the topology was
build wrong, it assumes the LLC mask to include at least the SMT CPUs.
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Tested-by: Bruno Wolff III <bruno@wolff.to>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140722133514.GM12054@laptop.lan
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The forthcoming patch will make <acpi/acpi.h> to be visible to all kernel
source code. Thus for the architectures that do not support ACPI and
haven't implemented <asm/acenv.h>, we need to make it excluded.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
GHES currently maps two pages with atomic_ioremap. From now
on, NMI is architectural depended so there is no need to allocate
an NMI page for platforms without NMI support.
To make it possible to not use a second page, swap the existing
page order so that the IRQ context page is first, and the optional
NMI context page is second. Then, use HAVE_ACPI_APEI_NMI to decide
how many pages are to be allocated.
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Currently APEI depends on x86 architecture. It is because of NMI hardware
error notification of GHES which is currently supported by x86 only.
However, many other APEI features can be still used perfectly by other
architectures.
This commit adds two symbols:
1. HAVE_ACPI_APEI for those archs which support APEI.
2. HAVE_ACPI_APEI_NMI which is used for NMI code isolation in ghes.c
file. NMI related data and functions are grouped so they can be wrapped
inside one #ifdef section. Appropriate function stubs are provided for
!NMI case.
Note there is no functional changes for x86 due to hard selected
HAVE_ACPI_APEI and HAVE_ACPI_APEI_NMI symbols.
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This commit abstracts MCE calls and provides weak corresponding default
implementation for those architectures which do not need arch specific
actions. Each platform willing to do additional architectural actions
should provides desired function definition. It allows us to avoid wrap
code into #ifdef in generic code and prevent new platform from introducing
dummy stub function too.
Initially, there are two APEI arch-specific calls:
- arch_apei_enable_cmcff()
- arch_apei_report_mem_error()
Both interact with MCE driver for X86 architecture.
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Commit 554086d ("x86_32, entry: Do syscall exit work on badsys
(CVE-2014-4508)") introduced a regression in the x86_32 syscall entry
code, resulting in syscall() not returning proper errors for undefined
syscalls on CPUs supporting the sysenter feature.
The following code:
> int result = syscall(666);
> printf("result=%d errno=%d error=%s\n", result, errno, strerror(errno));
results in:
> result=666 errno=0 error=Success
Obviously, the syscall return value is the called syscall number, but it
should have been an ENOSYS error. When run under ptrace it behaves
correctly, which makes it hard to debug in the wild:
> result=-1 errno=38 error=Function not implemented
The %eax register is the return value register. For debugging via ptrace
the syscall entry code stores the complete register context on the
stack. The badsys handlers only store the ENOSYS error code in the
ptrace register set and do not set %eax like a regular syscall handler
would. The old resume_userspace call chain contains code that clobbers
%eax and it restores %eax from the ptrace registers afterwards. The same
goes for the ptrace-enabled call chain. When ptrace is not used, the
syscall return value is the passed-in syscall number from the untouched
%eax register.
Use %eax as the return value register in syscall_badsys and
sysenter_badsys, like a real syscall handler does, and have the caller
push the value onto the stack for ptrace access.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Link: http://lkml.kernel.org/r/alpine.LNX.2.11.1407221022380.31021@titan.int.lan.stealer.net
Reviewed-and-tested-by: Andy Lutomirski <luto@amacapital.net>
Cc: <stable@vger.kernel.org> # If 554086d is backported
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
an x86 change too and it is a regression from 3.14. As it only affects
nested virtualization and there were other changes in this area in 3.16,
I am not nominating it for 3.15-stable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=Vdqn
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"These are mostly PPC changes for 3.16-new things. However, there is
an x86 change too and it is a regression from 3.14. As it only
affects nested virtualization and there were other changes in this
area in 3.16, I am not nominating it for 3.15-stable"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Check for nested events if there is an injectable interrupt
KVM: PPC: RTAS: Do byte swaps explicitly
KVM: PPC: Book3S PR: Fix ABIv2 on LE
KVM: PPC: Assembly functions exported to modules need _GLOBAL_TOC()
PPC: Add _GLOBAL_TOC for 32bit
KVM: PPC: BOOK3S: HV: Use base page size when comparing against slb value
KVM: PPC: Book3E: Unlock mmu_lock when setting caching atttribute
BorisO reports that misc_register() fails often on xen. The current code
unregisters the CPU hotplug notifier in that case. If then a CPU is
offlined and onlined back again, we end up with a second timer running
on that CPU, leading to soft lockups and system hangs.
So let's leave the hotcpu notifier always registered - even if
mce_device_create failed for some cores and never unreg it so that we
can deal with the timer handling accordingly.
Reported-and-Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: http://lkml.kernel.org/r/1403274493-1371-1-git-send-email-boris.ostrovsky@oracle.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Haswell and newer Intel CPUs have support for RTM, and in that case DR6.RTM is
not fixed to 1 and DR7.RTM is not fixed to zero. That is not the case in the
current KVM implementation. This bug is apparent only if the MOV-DR instruction
is emulated or the host also debugs the guest.
This patch is a partial fix which enables DR6.RTM and DR7.RTM to be cleared and
set respectively. It also sets DR6.RTM upon every debug exception. Obviously,
it is not a complete fix, as debugging of RTM is still unsupported.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
free_nested needs the loaded_vmcs to be valid if it is a vmcs02, in
order to detach it from the shadow vmcs. However, this is not
available anymore after commit 26a865f4aa (KVM: VMX: fix use after
free of vmx->loaded_vmcs, 2014-01-03).
Revert that patch, and fix its problem by forcing a vmcs01 as the
active VMCS before freeing all the nested VMX state.
Reported-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Tested-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The use of _PDC is deprecated in ACPI 3.0 in favor of _OSC,
as ARM platform is supported only in ACPI 5.0 or higher version,
_PDC will not be used in ARM platform, so make Make _PDC only for
platforms with Intel CPUs.
Introduce ARCH_MIGHT_HAVE_ACPI_PDC and move _PDC related code in
ACPI processor driver into a single file processor_pdc.c, make x86
and ia64 select it when ACPI is enabled.
This patch also use pr_* to replace printk to fix the checkpatch
warning and factor acpi_processor_alloc_pdc() a little bit to
avoid duplicate pr_err() code.
Suggested-by: Robert Richter <rric@kernel.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now ARM64 support is being added to ACPI so architecture specific
values can not be used in core ACPI code.
Following on the patch "ACPI / processor: Check if LAPIC is present
during initialization" which uses acpi_lapic in acpi_processor.c,
on ARM64 platform, GIC is used instead of local APIC, so acpi_lapic
is not a suitable value for ARM64.
What is actually important at this point is if there is/are CPU
entry/entries (Local APIC/SAPIC, GICC) in MADT, so introduce
acpi_has_cpu_in_madt() to be arch specific and generic.
Signed-off-by: Graeme Gregory <graeme.gregory@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With the addition of ARM64 that does not have a traditional BIOS to
scan, add a config option which is selected on x86 (ia64 doesn't need
it either, it is EFI/UEFI based system) to do the traditional BIOS
scanning for tables.
Signed-off-by: Graeme Gregory <graeme.gregory@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If the RFLAGS.RF is set, then no #DB should occur on instruction breakpoints.
However, the KVM emulator injects #DB regardless to RFLAGS.RF. This patch fixes
this behavior. KVM, however, still appears not to update RFLAGS.RF correctly,
regardless of this patch.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
RFLAGS.RF was cleaned in several functions (e.g., syscall) in the x86 emulator.
Now that we clear it before the execution of an instruction in the emulator, we
can remove the specific cleanup of RFLAGS.RF.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When an instruction is emulated RFLAGS.RF should be cleared. KVM previously did
not do so. This patch clears RFLAGS.RF after interception is done. If a fault
occurs during the instruction, RFLAGS.RF will be set by a previous patch. This
patch does not handle the case of traps/interrupts during rep-strings. Traps
are only expected to occur on debug watchpoints, and those are anyhow not
handled by the emulator.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
RFLAGS.RF is always zero after popf. Therefore, popf should not updated RF, as
anyhow emulating popf, just as any other instruction should clear RFLAGS.RF.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When skipping an emulated instruction, rflags.rf should be cleared as it would
be on real x86 CPU.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull locking fixes from Thomas Gleixner:
"The locking department delivers:
- A rather large and intrusive bundle of fixes to address serious
performance regressions introduced by the new rwsem / mcs
technology. Simpler solutions have been discussed, but they would
have been ugly bandaids with more risk than doing the right thing.
- Make the rwsem spin on owner technology opt-in for architectures
and enable it only on the known to work ones.
- A few fixes to the lockdep userspace library"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/rwsem: Add CONFIG_RWSEM_SPIN_ON_OWNER
locking/mutex: Disable optimistic spinning on some architectures
locking/rwsem: Reduce the size of struct rw_semaphore
locking/rwsem: Rename 'activity' to 'count'
locking/spinlocks/mcs: Micro-optimize osq_unlock()
locking/spinlocks/mcs: Introduce and use init macro and function for osq locks
locking/spinlocks/mcs: Convert osq lock to atomic_t to reduce overhead
locking/spinlocks/mcs: Rename optimistic_spin_queue() to optimistic_spin_node()
locking/rwsem: Allow conservative optimistic spinning when readers have lock
tools/liblockdep: Account for bitfield changes in lockdeps lock_acquire
tools/liblockdep: Remove debug print left over from development
tools/liblockdep: Fix comparison of a boolean value with a value of 2
Pull x86 fixes from Peter Anvin:
"A couple of key fixes and a few less critical ones. The main ones
are:
- add a .bss section to the PE/COFF headers when building with EFI
stub
- invoke the correct paravirt magic when building the espfix page
tables
Unfortunately both of these areas also have at least one additional
fix each still in thie pipeline, but which are not yet ready to push"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Remove unused variable "polling"
x86/espfix/xen: Fix allocation of pages for paravirt page tables
x86/efi: Include a .bss section within the PE/COFF headers
efi: fdt: Do not report an error during boot if UEFI is not available
efi/arm64: efistub: remove local copy of linux_banner
Compiler complains in the following way when x86 32-bit kernel
with Xen support is build:
CC arch/x86/xen/enlighten.o
arch/x86/xen/enlighten.c: In function ‘xen_start_kernel’:
arch/x86/xen/enlighten.c:1726:3: warning: right shift count >= width of type [enabled by default]
Such line contains following EFI initialization code:
boot_params.efi_info.efi_systab_hi = (__u32)(__pa(efi_systab_xen) >> 32);
There is no issue if x86 64-bit kernel is build. However, 32-bit case
generate warning (even if that code will not be executed because Xen
does not work on 32-bit EFI platforms) due to __pa() returning unsigned long
type which has 32-bits width. So move whole EFI initialization stuff
to separate function and build it conditionally to avoid above mentioned
warning on x86 32-bit architecture.
Signed-off-by: Daniel Kiper <daniel.kiper@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
The EFI boot stub goes to great pains to relocate the kernel image to
an appropriately aligned address, as indicated by the ->kernel_alignment
field in the bzImage header. However, for the PE stub entry case, we
can request that the EFI PE/COFF loader do the work for us.
Fix by exposing the desired alignment via the SectionAlignment field
in the PE/COFF headers. Despite its name, this field provides an
overall alignment requirement for the loaded file. (Naturally, the
FileAlignment field describes the alignment for individual sections.)
There is no way in the PE/COFF headers to express the concept of
min_alignment; we therefore do not expose the minimum (as opposed to
preferred) alignment.
Signed-off-by: Michael Brown <mbrown@fensystems.co.uk>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Hopefully this will enable us to better debug:
https://bugzilla.kernel.org/show_bug.cgi?id=68761
Signed-off-by: Ulf Winkelvos <ulf@winkelvos.de>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
efi_set_rtc_mmss() is never used to set RTC due to bugs found
on many EFI platforms. It is set directly by mach_set_rtc_mmss().
Hence, remove unused efi_set_rtc_mmss() function.
Signed-off-by: Daniel Kiper <daniel.kiper@oracle.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
We've got constants, so let's use them instead of hard-coded values.
Signed-off-by: Daniel Kiper <daniel.kiper@oracle.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
This patch enables EFI usage under Xen dom0. Standard EFI Linux
Kernel infrastructure cannot be used because it requires direct
access to EFI data and code. However, in dom0 case it is not possible
because above mentioned EFI stuff is fully owned and controlled
by Xen hypervisor. In this case all calls from dom0 to EFI must
be requested via special hypercall which in turn executes relevant
EFI code in behalf of dom0.
When dom0 kernel boots it checks for EFI availability on a machine.
If it is detected then artificial EFI system table is filled.
Native EFI callas are replaced by functions which mimics them
by calling relevant hypercall. Later pointer to EFI system table
is passed to standard EFI machinery and it continues EFI subsystem
initialization taking into account that there is no direct access
to EFI boot services, runtime, tables, structures, etc. After that
system runs as usual.
This patch is based on Jan Beulich and Tang Liang work.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Tang Liang <liang.tang@oracle.com>
Signed-off-by: Daniel Kiper <daniel.kiper@oracle.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Remove redundant set_bit(EFI_MEMMAP, &efi.flags) call.
It is executed earlier in efi_memmap_init().
Signed-off-by: Daniel Kiper <daniel.kiper@oracle.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Remove redundant set_bit(EFI_SYSTEM_TABLES, &efi.flags) call.
It is executed earlier in efi_systab_init().
Signed-off-by: Daniel Kiper <daniel.kiper@oracle.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Introduce EFI_PARAVIRT flag. If it is set then kernel runs
on EFI platform but it has not direct control on EFI stuff
like EFI runtime, tables, structures, etc. If not this means
that Linux Kernel has direct access to EFI infrastructure
and everything runs as usual.
This functionality is used in Xen dom0 because hypervisor
has full control on EFI stuff and all calls from dom0 to
EFI must be requested via special hypercall which in turn
executes relevant EFI code in behalf of dom0.
Signed-off-by: Daniel Kiper <daniel.kiper@oracle.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Do not access EFI memory map if it is not available. At least
Xen dom0 EFI implementation does not have an access to it.
Signed-off-by: Daniel Kiper <daniel.kiper@oracle.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Linus Torvalds
Matt Fleming
Mark Brown
Dan Carpenter
Alexei Starovoitov
H. Peter Anvin
Matt Rushton
Dave Hansen
Dave Hansen
David Rientjes
Mark D Rustad
David S. Miller
Chris J Arges
David Vrabel
Andy Lutomirski
Alexander Graf
Ingo Molnar
Rafael J. Wysocki
Li, Aubrey
Paolo Bonzini
Nadav Amit
Thomas Gleixner
John Stultz
Peter Zijlstra
Lv Zheng
Tomasz Nowicki
Sven Wegener
Borislav Petkov
Hanjun Guo
Graeme Gregory
Daniel Kiper
Michael Brown
Ulf Winkelvos