This also works around a bogus gcc warning generated by an
upcoming patch from Eric Dumazet that rearranges the layout
of struct flowi4.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables or updates support for the CC770 and AN82527
CAN controller on the TQM8548 and TQM8xx boards.
CC: devicetree-discuss@lists.ozlabs.org
CC: linuxppc-dev@ozlabs.org
CC: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver works with both, static platform data and device tree
bindings. It has been tested on a TQM855L board with two AN82527
CAN controllers on the local bus.
CC: Devicetree-discuss@lists.ozlabs.org
CC: linuxppc-dev@ozlabs.org
CC: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for legacy Bosch CC770 and Intel AN82527 CAN
controllers on the ISA or PC-104 bus. The I/O port or memory address
and the IRQ number must be specified via module parameters:
insmod cc770_isa.ko port=0x310,0x380 irq=7,11
for ISA devices using I/O ports or:
insmod cc770_isa.ko mem=0xd1000,0xd1000 irq=7,11
for memory mapped ISA devices.
Indirect access via address and data port is supported as well:
insmod cc770_isa.ko port=0x310,0x380 indirect=1 irq=7,11
Furthermore, the following mode parameter can be defined:
clk: External oscillator clock frequency (default=16000000 [16 MHz])
cir: CPU interface register (default=0x40 [DSC])
bcr: Bus configuration register (default=0x40 [CBY])
cor: Clockout register (default=0x00)
Note: for clk, cir, bcr and cor, the first argument re-defines the
default for all other devices, e.g.:
insmod cc770_isa.ko mem=0xd1000,0xd1000 irq=7,11 clk=24000000
is equivalent to
insmod cc770_isa.ko mem=0xd1000,0xd1000 irq=7,11 clk=24000000,24000000
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
At this point the variable j is always set to 7 and the code within
the loop has to run only once anyway.
As suggested by David Miller:
"You can simply this even further since p[7] is what is used here,
and this means len is one, the inner loop therefore executes only
once, and the p[7].field value is not used (it's zero in the table)
and the write to it is completely thrown away."
Signed-off-by: Patrick Kelle <patrick.kelle81@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit b00055aacd ([NET] core: add RFC2863 operstate) changed
net_device flags from unsigned short to unsigned int.
Some core functions still assume its an unsigned short.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include linux/if_ether.h to fix below build errors:
CC arch/arm/mach-kirkwood/common.o
In file included from arch/arm/mach-kirkwood/common.c:19:
include/net/dsa.h: In function 'dsa_uses_dsa_tags':
include/net/dsa.h:192: error: 'ETH_P_DSA' undeclared (first use in this function)
include/net/dsa.h:192: error: (Each undeclared identifier is reported only once
include/net/dsa.h:192: error: for each function it appears in.)
include/net/dsa.h: In function 'dsa_uses_trailer_tags':
include/net/dsa.h:197: error: 'ETH_P_TRAILER' undeclared (first use in this function)
make[1]: *** [arch/arm/mach-kirkwood/common.o] Error 1
make: *** [arch/arm/mach-kirkwood] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ERROR: "__udivdi3" [net/sched/sch_netem.ko] undefined!
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix meta data raid-repair merge problem
Btrfs: skip allocation attempt from empty cluster
Btrfs: skip block groups without enough space for a cluster
Btrfs: start search for new cluster at the beginning
Btrfs: reset cluster's max_size when creating bitmap
Btrfs: initialize new bitmaps' list
Btrfs: fix oops when calling statfs on readonly device
Btrfs: Don't error on resizing FS to same size
Btrfs: fix deadlock on metadata reservation when evicting a inode
Fix URL of btrfs-progs git repository in docs
btrfs scrub: handle -ENOMEM from init_ipath()
Commit 4a54c8c16 introduced raid-repair, killing the individual
readpage_io_failed_hook entries from inode.c and disk-io.c. Commit
4bb31e92 introduced new readahead code, adding a readpage_io_failed_hook to
disk-io.c.
The raid-repair commit had logic to disable raid-repair, if
readpage_io_failed_hook is set. Thus, the readahead commit effectively
disabled raid-repair for meta data.
This commit changes the logic to always attempt raid-repair when needed and
call the readpage_io_failed_hook in case raid-repair fails. This is much
more straight forward and should have been like that from the beginning.
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
Reported-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Within nested statements, the break statement terminates only the
do, for, switch, or while statement that immediately encloses it,
So replace the break with goto.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused enum cfcnfg_phy_type and the parameter to cfserl_create.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enrolling CAIF link layers are refactored.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow NULL pointer in cfpkt_extr_head in order to
skip past header data.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit a4a710c4a7 (pkt_sched: Change PSCHED_SHIFT from 10 to
6) it seems RED/GRED are broken.
red_calc_qavg_from_idle_time() computes a delay in us units, but this
delay is now 16 times bigger than real delay, so the final qavg result
smaller than expected.
Use standard kernel time services since there is no need to obfuscate
them.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently netem is not in the ability to emulate channel bandwidth. Only static
delay (and optional random jitter) can be configured.
To emulate the channel rate the token bucket filter (sch_tbf) can be used. But
TBF has some major emulation flaws. The buffer (token bucket depth/rate) cannot
be 0. Also the idea behind TBF is that the credit (token in buckets) fills if
no packet is transmitted. So that there is always a "positive" credit for new
packets. In real life this behavior contradicts the law of nature where
nothing can travel faster as speed of light. E.g.: on an emulated 1000 byte/s
link a small IPv4/TCP SYN packet with ~50 byte require ~0.05 seconds - not 0
seconds.
Netem is an excellent place to implement a rate limiting feature: static
delay is already implemented, tfifo already has time information and the
user can skip TBF configuration completely.
This patch implement rate feature which can be configured via tc. e.g:
tc qdisc add dev eth0 root netem rate 10kbit
To emulate a link of 5000byte/s and add an additional static delay of 10ms:
tc qdisc add dev eth0 root netem delay 10ms rate 5KBps
Note: similar to TBF the rate extension is bounded to the kernel timing
system. Depending on the architecture timer granularity, higher rates (e.g.
10mbit/s and higher) tend to transmission bursts. Also note: further queues
living in network adaptors; see ethtool(8).
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@drr.davemloft.net>
Need not to used 'delta' flag when add single-source to interface
filter source list.
Signed-off-by: Jun Zhao <mypopydev@gmail.com>
Signed-off-by: David S. Miller <davem@drr.davemloft.net>
Need not to used 'delta' flag when add single-source to interface
filter source list.
Signed-off-by: Jun Zhao <mypopydev@gmail.com>
Signed-off-by: David S. Miller <davem@drr.davemloft.net>
Only use the primary address of the bond device
for master_ip. This will prevent changing the ARP source
address in Active-Backup mode whenever a secondry address
is added to the bond device.
Signed-off-by: Henrik Saavedra Persson <henrik.e.persson@ericsson.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@drr.davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: twl: fix twl4030 support for smps regulators
regulator: fix use after free bug
regulator: aat2870: Fix the logic of checking if no id is matched in aat2870_get_regulator
kernel/sched.c:7354:2: warning: initialization from incompatible pointer type
Align cpu_coregroup_mask prototype interface with sched_domain_mask_f typedef
use int cpu instead of unsigned int cpu
Cc: <stable@vger.kernel.org>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The SWP instruction is deprecated on ARMv6 and with ARMv7 it will be
UNDEFINED when CONFIG_SWP_EMULATE is selected. In this case, probing a
SWP instruction will cause an oops when the kprobes emulation code
executes an undefined instruction.
As the SWP instruction should be rare or non-existent in kernels for
ARMv6 and later, we can simply avoid these problems by not allowing
probing of these.
Reported-by: Leif Lindholm <leif.lindholm@arm.com>
Tested-by: Leif Lindholm <leif.lindholm@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is a kprobes testcase for the instruction "strd r2, [r3], r4".
This has unpredictable behaviour as it uses r3 for register writeback
addressing and also stores it to memory.
On a cortex A9, this testcase would fail because the instruction writes
the updated value of r3 to memory, whereas the kprobes emulation code
writes the original value.
Fix this by changing testcase to used r5 instead of r3.
Reported-by: Leif Lindholm <leif.lindholm@arm.com>
Tested-by: Leif Lindholm <leif.lindholm@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Instead of instantiating an entire new neigh_table instance
just for ATM handling, use the neigh device private facility.
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev->neigh_priv_len records the private area length.
This will trigger for neigh_table objects which set tbl->entry_size
to zero, and the first instances of this will be forthcoming.
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to alloc for device specific private areas for
neighbour entries, and in order to do that we have to move
away from the fixed allocation size enforced by using
neigh_table->kmem_cachep
As a nice side effect we can now use kfree_rcu().
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit f2c31e32b3 (fix NULL dereferences in check_peer_redir()),
dst_get_neighbour() should be guarded by rcu_read_lock() /
rcu_read_unlock() section.
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As soon as skb is pushed to hardware, it can be completed and freed, so
we should not dereference skb anymore.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need rcu_read_lock() protection before using dst_get_neighbour(), and
we must cache its value (pass it to __teql_resolve())
teql_master_xmit() is called under rcu_read_lock_bh() protection, its
not enough.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to bnx2 to use byte queue limits.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 230dec6 (net/fec: add imx6q enet support) the FEC driver is no
longer built by default for i.MX SoCs.
Let the FEC driver be built by default again.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rick Jones reported that TCP_CONGESTION sockopt performed on a listener
was ignored for its children sockets : right after accept() the
congestion control for new socket is the system default one.
This seems an oversight of the initial design (quoted from Stephen)
Based on prior investigation and patch from Rick.
Reported-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: Yuchung Cheng <ycheng@google.com>
Tested-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we don't have a cluster, don't bother trying to allocate from it,
jumping right away to the attempt to allocate a new cluster.
Signed-off-by: Alexandre Oliva <oliva@lsd.ic.unicamp.br>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
We test whether a block group has enough free space to hold the
requested block, but when we're doing clustered allocation, we can
save some cycles by testing whether it has enough room for the cluster
upfront, otherwise we end up attempting to set up a cluster and
failing. Only in the NO_EMPTY_SIZE loop do we attempt an unclustered
allocation, and by then we'll have zeroed the cluster size, so this
patch won't stop us from using the block group as a last resort.
Signed-off-by: Alexandre Oliva <oliva@lsd.ic.unicamp.br>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Instead of starting at zero (offset is always zero), request a cluster
starting at search_start, that denotes the beginning of the current
block group.
Signed-off-by: Alexandre Oliva <oliva@lsd.ic.unicamp.br>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The field that indicates the size of the largest contiguous chunk of
free space in the cluster is not initialized when setting up bitmaps,
it's only increased when we find a larger contiguous chunk. We end up
retaining a larger value than appropriate for highly-fragmented
clusters, which may cause pointless searches for large contiguous
groups, and even cause clusters that do not meet the density
requirements to be set up.
Signed-off-by: Alexandre Oliva <oliva@lsd.ic.unicamp.br>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
We're failing to create clusters with bitmaps because
setup_cluster_no_bitmap checks that the list is empty before inserting
the bitmap entry in the list for setup_cluster_bitmap, but the list
field is only initialized when it is restored from the on-disk free
space cache, or when it is written out to disk.
Besides a potential race condition due to the multiple use of the list
field, filesystem performance severely degrades over time: as we use
up all non-bitmap free extents, the try-to-set-up-cluster dance is
done at every metadata block allocation. For every block group, we
fail to set up a cluster, and after failing on them all up to twice,
we fall back to the much slower unclustered allocation.
To make matters worse, before the unclustered allocation, we try to
create new block groups until we reach the 1% threshold, which
introduces additional bitmaps and thus block groups that we'll iterate
over at each metadata block request.
To reproduce this bug:
# dd if=/dev/zero of=img bs=1M count=256
# mkfs.btrfs img
# losetup -r /dev/loop1 img
# mount /dev/loop1 /mnt
OOPS!!
It triggered BUG_ON(!nr_devices) in btrfs_calc_avail_data_space().
To fix this, instead of checking write-only devices, we check all open
deivces:
# df -h /dev/loop1
Filesystem Size Used Avail Use% Mounted on
/dev/loop1 250M 28K 238M 1% /mnt
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
It seems overly harsh to fail a resize of a btrfs file system to the
same size when a shrink or grow would succeed. User app GParted trips
over this error. Allow it by bypassing the shrink or grow operation.
Signed-off-by: Mike Fleetwood <mike.fleetwood@googlemail.com>
David S. Miller
Wolfgang Grandegger
Patrick Kelle
Eric Dumazet
Axel Lin
Linus Torvalds
Jan Schmidt
RongQing.Li
sjur.brandeland@stericsson.com
Hagen Paul Pfeifer
Jun Zhao
Henrik Saavedra Persson
Vincent Guittot
Jon Medhurst (Tixy)
Fabio Estevam
John W. Linville
Alexandre Oliva
Li Zefan
Mike Fleetwood