No more users and there is no desire to grow new ones.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/8735hir0j4.ffs@tglx
flush_smp_call_function_queue() invokes do_softirq() which is not available
on PREEMPT_RT. flush_smp_call_function_queue() is invoked from the idle
task and the migration task with preemption or interrupts disabled.
So RT kernels cannot process soft interrupts in that context as that has to
acquire 'sleeping spinlocks' which is not possible with preemption or
interrupts disabled and forbidden from the idle task anyway.
The currently known SMP function call which raises a soft interrupt is in
the block layer, but this functionality is not enabled on RT kernels due to
latency and performance reasons.
RT could wake up ksoftirqd unconditionally, but this wants to be avoided if
there were soft interrupts pending already when this is invoked in the
context of the migration task. The migration task might have preempted a
threaded interrupt handler which raised a soft interrupt, but did not reach
the local_bh_enable() to process it. The "running" ksoftirqd might prevent
the handling in the interrupt thread context which is causing latency
issues.
Add a new function which handles this case explicitely for RT and falls
back to do_softirq() on !RT kernels. In the RT case this warns when one of
the flushed SMP function calls raised a soft interrupt so this can be
investigated.
[ tglx: Moved the RT part out of SMP code ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/YgKgL6aPj8aBES6G@linutronix.de
Link: https://lore.kernel.org/r/20220413133024.356509586@linutronix.de
The following warning may appear while setting a CPU down:
NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #20!!!
The IRQ_POLL_SOFTIRQ vector can be raised during the hotplug cpu_down()
path after ksoftirqd is parked and before the CPU actually dies. However
this is handled afterward at the CPUHP_IRQ_POLL_DEAD stage where the
queue gets migrated.
Hence this warning can be considered spurious and the vector can join
the "hotplug-safe" list.
Reported-and-tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Paul E. McKenney <paulmck@kernel.org>
Cc: Paul Menzel <pmenzel@molgen.mpg.de>
RCU_SOFTIRQ used to be special in that it could be raised on purpose
within the idle path to prevent from stopping the tick. Some code still
prevents from unnecessary warnings related to this specific behaviour
while entering in dynticks-idle mode.
However the nohz layout has changed quite a bit in ten years, and the
removal of CONFIG_RCU_FAST_NO_HZ has been the final straw to this
safe-conduct. Now the RCU_SOFTIRQ vector is expected to be raised from
sane places.
A remaining corner case is admitted though when the vector is invoked
in fragile hotplug path.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Paul E. McKenney <paulmck@kernel.org>
Cc: Paul Menzel <pmenzel@molgen.mpg.de>
The discussion about removing the side effect of irq_set_affinity_hint() of
actually applying the cpumask (if not NULL) as affinity to the interrupt,
unearthed a few unpleasantries:
1) The modular perf drivers rely on the current behaviour for the very
wrong reasons.
2) While none of the other drivers prevents user space from changing
the affinity, a cursorily inspection shows that there are at least
expectations in some drivers.
#1 needs to be cleaned up anyway, so that's not a problem
#2 might result in subtle regressions especially when irqbalanced (which
nowadays ignores the affinity hint) is disabled.
Provide new interfaces:
irq_update_affinity_hint() - Only sets the affinity hint pointer
irq_set_affinity_and_hint() - Set the pointer and apply the affinity to
the interrupt
Make irq_set_affinity_hint() a wrapper around irq_apply_affinity_hint() and
document it to be phased out.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Nitesh Narayan Lal <nitesh@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20210501021832.743094-1-jesse.brandeburg@intel.com
Link: https://lore.kernel.org/r/20210903152430.244937-2-nitesh@redhat.com
With CONFIG_IRQ_FORCED_THREADING=y, testing the boolean force_irqthreads
could incur a cache line miss in invoke_softirq() and other places.
Replace the test with a static key to avoid the potential cache miss.
[ tglx: Dropped the IDE part, removed the export and updated blk-mq ]
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Tanner Love <tannerlove@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210602180338.3324213-1-tannerlove.kernel@gmail.com
Perf modules abuse irq_set_affinity_hint() to set the affinity of system
PMU interrupts just because irq_set_affinity() was not exported.
The fact that irq_set_affinity_hint() actually sets the affinity is a
non-documented side effect and the name is clearly saying it's a hint.
To clean this up, export the real affinity setter.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20210518093117.968251441@linutronix.de
The whole call to note_interrupt() can be avoided or return early when
interrupts would be marked accordingly. For IPI handlers which always
return HANDLED the whole procedure is pretty pointless to begin with.
Add a IRQF_NO_DEBUG flag and mark the interrupt accordingly if supplied
when the interrupt is requested.
When noirqdebug is set on the kernel commandline, then the interrupt is
marked unconditionally so that there is only one condition in the hotpath
to evaluate.
[ clg: Add changelog ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/7a8ad02f-63a8-c1aa-fdd1-39d973593d02@kaod.org
-- NOT FOR IMMEDIATE MERGING --
Now that all users of tasklet_disable() are invoked from sleepable context,
convert it to use tasklet_unlock_wait() which might sleep.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210309084242.726452321@linutronix.de
tasklet_unlock_spin_wait() spin waits for the TASKLET_STATE_SCHED bit in
the tasklet state to be cleared. This works on !RT nicely because the
corresponding execution can only happen on a different CPU.
On RT softirq processing is preemptible, therefore a task preempting the
softirq processing thread can spin forever.
Prevent this by invoking local_bh_disable()/enable() inside the loop. In
case that the softirq processing thread was preempted by the current task,
current will block on the local lock which yields the CPU to the preempted
softirq processing thread. If the tasklet is processed on a different CPU
then the local_bh_disable()/enable() pair is just a waste of processor
cycles.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210309084241.988908275@linutronix.de
tasklet_unlock_wait() spin waits for TASKLET_STATE_RUN to be cleared. This
is wasting CPU cycles in a tight loop which is especially painful in a
guest when the CPU running the tasklet is scheduled out.
tasklet_unlock_wait() is invoked from tasklet_kill() which is used in
teardown paths and not performance critical at all. Replace the spin wait
with wait_var_event().
There are no users of tasklet_unlock_wait() which are invoked from atomic
contexts. The usage in tasklet_disable() has been replaced temporarily with
the spin waiting variant until the atomic users are fixed up and will be
converted to the sleep wait variant later.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210309084241.783936921@linutronix.de
To ease the transition use spin waiting in tasklet_disable() until all
usage sites from atomic context have been cleaned up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210309084241.685352806@linutronix.de
Replacing the spin wait loops in tasklet_unlock_wait() with
wait_var_event() is not possible as a handful of tasklet_disable()
invocations are happening in atomic context. All other invocations are in
teardown paths which can sleep.
Provide tasklet_disable_in_atomic() and tasklet_unlock_spin_wait() to
convert the few atomic use cases over, which allows to change
tasklet_disable() and tasklet_unlock_wait() in a later step.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210309084241.563164193@linutronix.de
Inlines exist for a reason.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210309084241.407702697@linutronix.de
A barrier() in a tight loop which waits for something to happen on a remote
CPU is a pointless exercise. Replace it with cpu_relax() which allows HT
siblings to make progress.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210309084241.249343366@linutronix.de
Ever since RCU was converted to softirq, it has no users.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/r/20210306213658.12862-1-dave@stgolabs.net
Many drivers don't want interrupts enabled automatically via request_irq().
So they are handling this issue by either way of the below two:
(1)
irq_set_status_flags(irq, IRQ_NOAUTOEN);
request_irq(dev, irq...);
(2)
request_irq(dev, irq...);
disable_irq(irq);
The code in the second way is silly and unsafe. In the small time gap
between request_irq() and disable_irq(), interrupts can still come.
The code in the first way is safe though it's subobtimal.
Add a new IRQF_NO_AUTOEN flag which can be handed in by drivers to
request_irq() and request_nmi(). It prevents the automatic enabling of the
requested interrupt/nmi in the same safe way as #1 above. With that the
various usage sites of #1 and #2 above can be simplified and corrected.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: dmitry.torokhov@gmail.com
Link: https://lore.kernel.org/r/20210302224916.13980-2-song.bao.hua@hisilicon.com
To avoid include recursion hell move the do_softirq_own_stack() related
content into a generic asm header and include it from all places in arch/
which need the prototype.
This allows architectures to provide an inline implementation of
do_softirq_own_stack() without introducing a lot of #ifdeffery all over the
place.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210210002513.289960691@linutronix.de
To prepare for inlining do_softirq_own_stack() replace
__ARCH_HAS_DO_SOFTIRQ with a Kconfig switch and select it in the affected
architectures.
This allows in the next step to move the function prototype and the inline
stub into a seperate asm-generic header file which is required to avoid
include recursion.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210210002513.181713427@linutronix.de
This function uses irq_to_desc() and is going to be used by modules to
replace the open coded irq_to_desc() (ab)usage. The final goal is to remove
the export of irq_to_desc() so driver cannot fiddle with it anymore.
Move it into the core code and fixup the usage sites to include the proper
header.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20201210194042.548936472@linutronix.de
Add a function to allow the affinity of an interrupt be switched to
managed, such that interrupts allocated for platform devices may be
managed.
This new interface has certain limitations, and attempts to use it in the
following circumstances will fail:
- For when the kernel is configured for generic IRQ reservation mode (in
config GENERIC_IRQ_RESERVATION_MODE). The reason being that it could
conflict with managed vs. non-managed interrupt accounting.
- The interrupt is already started, which should not be the case during
init
- The interrupt is already configured as managed, which means double init
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1606905417-183214-2-git-send-email-john.garry@huawei.com
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Conversion done using the script at:
https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.pl
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nowadays, modern kernel subsystems that use callbacks pass the data
structure associated with a given callback as argument to the callback.
The tasklet subsystem remains one which passes an arbitrary unsigned
long to the callback function. This has several problems:
- This keeps an extra field for storing the argument in each tasklet
data structure, it bloats the tasklet_struct structure with a redundant
.data field
- No type checking can be performed on this argument. Instead of
using container_of() like other callback subsystems, it forces callbacks
to do explicit type cast of the unsigned long argument into the required
object type.
- Buffer overflows can overwrite the .func and the .data field, so
an attacker can easily overwrite the function and its first argument
to whatever it wants.
Add a new tasklet initialization API, via DECLARE_TASKLET() and
tasklet_setup(), which will replace the existing ones.
This work is greatly inspired by the timer_struct conversion series,
see commit e99e88a9d2 ("treewide: setup_timer() -> timer_setup()")
To avoid problems with both -Wcast-function-type (which is enabled in
the kernel via -Wextra is several subsystems), and with mismatched
function prototypes when build with Control Flow Integrity enabled,
this adds the "use_callback" member to let the tasklet caller choose
which union member to call through. Once all old API uses are removed,
this and the .data member will be removed as well. (On 64-bit this does
not grow the struct size as the new member fills the hole after atomic_t,
which is also "int" sized.)
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Co-developed-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
This converts all the existing DECLARE_TASKLET() (and ...DISABLED)
macros with DECLARE_TASKLET_OLD() in preparation for refactoring the
tasklet callback type. All existing DECLARE_TASKLET() users had a "0"
data argument, it has been removed here as well.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
The entry rework moved interrupt entry code from the irqentry to the
noinstr section which made the irqentry section empty.
This breaks boundary checks which rely on the __irqentry_text_start/end
markers to find out whether a function in a stack trace is
interrupt/exception entry code. This affects the function graph tracer and
filter_irq_stacks().
As the IDT entry points are all sequentialy emitted this is rather simple
to unbreak by injecting __irqentry_text_start/end as global labels.
To make this work correctly:
- Remove the IRQENTRY_TEXT section from the x86 linker script
- Define __irqentry so it breaks the build if it's used
- Adjust the entry mirroring in PTI
- Remove the redundant kprobes and unwinder bound checks
Reported-by: Qian Cai <cai@lca.pw>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Error injection mechanisms need a half ways safe way to inject interrupts as
invoking generic_handle_irq() or the actual device interrupt handler
directly from e.g. a debugfs write is not guaranteed to be safe.
On x86 generic_handle_irq() is unsafe due to the hardware trainwreck which
is the base of x86 interrupt delivery and affinity management.
Move the irq debugfs injection code into a separate function which can be
used by error injection code as well.
The implementation prevents at least that state is corrupted, but it cannot
close a very tiny race window on x86 which might result in a stale and not
serviced device interrupt under very unlikely circumstances.
This is explicitly for debugging and testing and not for production use or
abuse in random driver code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lkml.kernel.org/r/20200306130623.990928309@linutronix.de
Pull timer updates from Ingo Molnar:
"The main changes in the timer code in this cycle were:
- Clockevent updates:
- timer-of framework cleanups. (Geert Uytterhoeven)
- Use timer-of for the renesas-ostm and the device name to prevent
name collision in case of multiple timers. (Geert Uytterhoeven)
- Check if there is an error after calling of_clk_get in asm9260
(Chuhong Yuan)
- ABI fix: Zero out high order bits of nanoseconds on compat
syscalls. This got broken a year ago, with apparently no side
effects so far.
Since the kernel would use random data otherwise I don't think we'd
have other options but to fix the bug, even if there was a side
effect to applications (Dmitry Safonov)
- Optimize ns_to_timespec64() on 32-bit systems: move away from
div_s64_rem() which can be slow, to div_u64_rem() which is faster
(Arnd Bergmann)
- Annotate KCSAN-reported false positive data races in
hrtimer_is_queued() users by moving timer->state handling over to
the READ_ONCE()/WRITE_ONCE() APIs. This documents these accesses
(Eric Dumazet)
- Misc cleanups and small fixes"
[ I undid the "ABI fix" and updated the comments instead. The reason
there were apparently no side effects is that the fix was a no-op.
The updated comment is to say _why_ it was a no-op. - Linus ]
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: Zero the upper 32-bits in __kernel_timespec on 32-bit
time: Rename tsk->real_start_time to ->start_boottime
hrtimer: Remove the comment about not used HRTIMER_SOFTIRQ
time: Fix spelling mistake in comment
time: Optimize ns_to_timespec64()
hrtimer: Annotate lockless access to timer->state
clocksource/drivers/asm9260: Add a check for of_clk_get
clocksource/drivers/renesas-ostm: Use unique device name instead of ostm
clocksource/drivers/renesas-ostm: Convert to timer_of
clocksource/drivers/timer-of: Use unique device name instead of timer
clocksource/drivers/timer-of: Convert last full_name to %pOF
While checking the results of the :c:func: removal, I noticed that there
was no documentation for request_irq(), and request_threaded_irq() was not
mentioned at all. Add a kerneldoc comment for request_irq() and add
request_threaded_irq() to the list of functions.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The softirq `HRTIMER_SOFTIRQ' was not used since commit c6eb3f70d4
("hrtimer: Get rid of hrtimer softirq").
But it got used again, beginning with commit 5da7016046 ("hrtimer:
Implement support for softirq based hrtimers"), which did not remove the
comment. Remove it now.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20191107091924.13410-1-bigeasy@linutronix.de
- Rework the main suspend-to-idle control flow to avoid repeating
"noirq" device resume and suspend operations in case of spurious
wakeups from the ACPI EC and decouple the ACPI EC wakeups support
from the LPS0 _DSM support (Rafael Wysocki).
- Extend the wakeup sources framework to expose wakeup sources as
device objects in sysfs (Tri Vo, Stephen Boyd).
- Expose system suspend statistics in sysfs (Kalesh Singh).
- Introduce a new haltpoll cpuidle driver and a new matching
governor for virtualized guests wanting to do guest-side polling
in the idle loop (Marcelo Tosatti, Joao Martins, Wanpeng Li,
Stephen Rothwell).
- Fix the menu and teo cpuidle governors to allow the scheduler tick
to be stopped if PM QoS is used to limit the CPU idle state exit
latency in some cases (Rafael Wysocki).
- Increase the resolution of the play_idle() argument to microseconds
for more fine-grained injection of CPU idle cycles (Daniel Lezcano).
- Switch over some users of cpuidle notifiers to the new QoS-based
frequency limits and drop the CPUFREQ_ADJUST and CPUFREQ_NOTIFY
policy notifier events (Viresh Kumar).
- Add new cpufreq driver based on nvmem for sun50i (Yangtao Li).
- Add support for MT8183 and MT8516 to the mediatek cpufreq driver
(Andrew-sh.Cheng, Fabien Parent).
- Add i.MX8MN support to the imx-cpufreq-dt cpufreq driver (Anson
Huang).
- Add qcs404 to cpufreq-dt-platdev blacklist (Jorge Ramirez-Ortiz).
- Update the qcom cpufreq driver (among other things, to make it
easier to extend and to use kryo cpufreq for other nvmem-based
SoCs) and add qcs404 support to it (Niklas Cassel, Douglas
RAILLARD, Sibi Sankar, Sricharan R).
- Fix assorted issues and make assorted minor improvements in the
cpufreq code (Colin Ian King, Douglas RAILLARD, Florian Fainelli,
Gustavo Silva, Hariprasad Kelam).
- Add new devfreq driver for NVidia Tegra20 (Dmitry Osipenko, Arnd
Bergmann).
- Add new Exynos PPMU events to devfreq events and extend that
mechanism (Lukasz Luba).
- Fix and clean up the exynos-bus devfreq driver (Kamil Konieczny).
- Improve devfreq documentation and governor code, fix spelling
typos in devfreq (Ezequiel Garcia, Krzysztof Kozlowski, Leonard
Crestez, MyungJoo Ham, Gaël PORTAY).
- Add regulators enable and disable to the OPP (operating performance
points) framework (Kamil Konieczny).
- Update the OPP framework to support multiple opp-suspend properties
(Anson Huang).
- Fix assorted issues and make assorted minor improvements in the OPP
code (Niklas Cassel, Viresh Kumar, Yue Hu).
- Clean up the generic power domains (genpd) framework (Ulf Hansson).
- Clean up assorted pieces of power management code and documentation
(Akinobu Mita, Amit Kucheria, Chuhong Yuan).
- Update the pm-graph tool to version 5.5 including multiple fixes
and improvements (Todd Brandt).
- Update the cpupower utility (Benjamin Weis, Geert Uytterhoeven,
Sébastien Szymanski).
-----BEGIN PGP SIGNATURE-----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=TBDQ
-----END PGP SIGNATURE-----
Merge tag 'pm-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These include a rework of the main suspend-to-idle code flow (related
to the handling of spurious wakeups), a switch over of several users
of cpufreq notifiers to QoS-based limits, a new devfreq driver for
Tegra20, a new cpuidle driver and governor for virtualized guests, an
extension of the wakeup sources framework to expose wakeup sources as
device objects in sysfs, and more.
Specifics:
- Rework the main suspend-to-idle control flow to avoid repeating
"noirq" device resume and suspend operations in case of spurious
wakeups from the ACPI EC and decouple the ACPI EC wakeups support
from the LPS0 _DSM support (Rafael Wysocki).
- Extend the wakeup sources framework to expose wakeup sources as
device objects in sysfs (Tri Vo, Stephen Boyd).
- Expose system suspend statistics in sysfs (Kalesh Singh).
- Introduce a new haltpoll cpuidle driver and a new matching governor
for virtualized guests wanting to do guest-side polling in the idle
loop (Marcelo Tosatti, Joao Martins, Wanpeng Li, Stephen Rothwell).
- Fix the menu and teo cpuidle governors to allow the scheduler tick
to be stopped if PM QoS is used to limit the CPU idle state exit
latency in some cases (Rafael Wysocki).
- Increase the resolution of the play_idle() argument to microseconds
for more fine-grained injection of CPU idle cycles (Daniel
Lezcano).
- Switch over some users of cpuidle notifiers to the new QoS-based
frequency limits and drop the CPUFREQ_ADJUST and CPUFREQ_NOTIFY
policy notifier events (Viresh Kumar).
- Add new cpufreq driver based on nvmem for sun50i (Yangtao Li).
- Add support for MT8183 and MT8516 to the mediatek cpufreq driver
(Andrew-sh.Cheng, Fabien Parent).
- Add i.MX8MN support to the imx-cpufreq-dt cpufreq driver (Anson
Huang).
- Add qcs404 to cpufreq-dt-platdev blacklist (Jorge Ramirez-Ortiz).
- Update the qcom cpufreq driver (among other things, to make it
easier to extend and to use kryo cpufreq for other nvmem-based
SoCs) and add qcs404 support to it (Niklas Cassel, Douglas
RAILLARD, Sibi Sankar, Sricharan R).
- Fix assorted issues and make assorted minor improvements in the
cpufreq code (Colin Ian King, Douglas RAILLARD, Florian Fainelli,
Gustavo Silva, Hariprasad Kelam).
- Add new devfreq driver for NVidia Tegra20 (Dmitry Osipenko, Arnd
Bergmann).
- Add new Exynos PPMU events to devfreq events and extend that
mechanism (Lukasz Luba).
- Fix and clean up the exynos-bus devfreq driver (Kamil Konieczny).
- Improve devfreq documentation and governor code, fix spelling typos
in devfreq (Ezequiel Garcia, Krzysztof Kozlowski, Leonard Crestez,
MyungJoo Ham, Gaël PORTAY).
- Add regulators enable and disable to the OPP (operating performance
points) framework (Kamil Konieczny).
- Update the OPP framework to support multiple opp-suspend properties
(Anson Huang).
- Fix assorted issues and make assorted minor improvements in the OPP
code (Niklas Cassel, Viresh Kumar, Yue Hu).
- Clean up the generic power domains (genpd) framework (Ulf Hansson).
- Clean up assorted pieces of power management code and documentation
(Akinobu Mita, Amit Kucheria, Chuhong Yuan).
- Update the pm-graph tool to version 5.5 including multiple fixes
and improvements (Todd Brandt).
- Update the cpupower utility (Benjamin Weis, Geert Uytterhoeven,
Sébastien Szymanski)"
* tag 'pm-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (126 commits)
cpuidle-haltpoll: Enable kvm guest polling when dedicated physical CPUs are available
cpuidle-haltpoll: do not set an owner to allow modunload
cpuidle-haltpoll: return -ENODEV on modinit failure
cpuidle-haltpoll: set haltpoll as preferred governor
cpuidle: allow governor switch on cpuidle_register_driver()
PM: runtime: Documentation: add runtime_status ABI document
pm-graph: make setVal unbuffered again for python2 and python3
powercap: idle_inject: Use higher resolution for idle injection
cpuidle: play_idle: Increase the resolution to usec
cpuidle-haltpoll: vcpu hotplug support
cpufreq: Add qcs404 to cpufreq-dt-platdev blacklist
cpufreq: qcom: Add support for qcs404 on nvmem driver
cpufreq: qcom: Refactor the driver to make it easier to extend
cpufreq: qcom: Re-organise kryo cpufreq to use it for other nvmem based qcom socs
dt-bindings: opp: Add qcom-opp bindings with properties needed for CPR
dt-bindings: opp: qcom-nvmem: Support pstates provided by a power domain
Documentation: cpufreq: Update policy notifier documentation
cpufreq: Remove CPUFREQ_ADJUST and CPUFREQ_NOTIFY policy notifier events
PM / Domains: Verify PM domain type in dev_pm_genpd_set_performance_state()
PM / Domains: Simplify genpd_lookup_dev()
...
Switch force_irqthreads from a boot time modifiable variable to a compile
time constant when CONFIG_PREEMPT_RT is enabled.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190816160923.12855-1-bigeasy@linutronix.de
Introduce a new function, rearm_wake_irq(), allowing a wakeup IRQ
to be armed for systen wakeup detection again without running any
action handlers associated with it after it has been armed for
wakeup detection and triggered.
That is useful for IRQs, like ACPI SCI, that may deliver wakeup
as well as non-wakeup interrupts when armed for systen wakeup
detection. In those cases, it may be possible to determine whether
or not the delivered interrupt is a systen wakeup one without
running the entire action handler (or handlers, if the IRQ is
shared) for the IRQ, and if the interrupt turns out to be a
non-wakeup one, the IRQ can be rearmed with the help of the
new function.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Convert the PM documents to ReST, in order to allow them to
build with Sphinx.
The conversion is actually:
- add blank lines and indentation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Srivatsa S. Bhat (VMware) <srivatsa@csail.mit.edu>
There are no more users of this interface.
Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Link: https://lkml.kernel.org/r/20190301224821.29843-4-bigeasy@linutronix.de
- Core pseudo-NMI handling code
- Allow the default irq domain to be retrieved
- A new interrupt controller for the Loongson LS1X platform
- Affinity support for the SiFive PLIC
- Better support for the iMX irqsteer driver
- NUMA aware memory allocations for GICv3
- A handful of other fixes (i8259, GICv3, PLIC)
-----BEGIN PGP SIGNATURE-----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=M6YA
-----END PGP SIGNATURE-----
Merge tag 'irqchip-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier
- Core pseudo-NMI handling code
- Allow the default irq domain to be retrieved
- A new interrupt controller for the Loongson LS1X platform
- Affinity support for the SiFive PLIC
- Better support for the iMX irqsteer driver
- NUMA aware memory allocations for GICv3
- A handful of other fixes (i8259, GICv3, PLIC)
The interrupt affinity spreading mechanism supports to spread out
affinities for one or more interrupt sets. A interrupt set contains one or
more interrupts. Each set is mapped to a specific functionality of a
device, e.g. general I/O queues and read I/O queus of multiqueue block
devices.
The number of interrupts per set is defined by the driver. It depends on
the total number of available interrupts for the device, which is
determined by the PCI capabilites and the availability of underlying CPU
resources, and the number of queues which the device provides and the
driver wants to instantiate.
The driver passes initial configuration for the interrupt allocation via a
pointer to struct irq_affinity.
Right now the allocation mechanism is complex as it requires to have a loop
in the driver to determine the maximum number of interrupts which are
provided by the PCI capabilities and the underlying CPU resources. This
loop would have to be replicated in every driver which wants to utilize
this mechanism. That's unwanted code duplication and error prone.
In order to move this into generic facilities it is required to have a
mechanism, which allows the recalculation of the interrupt sets and their
size, in the core code. As the core code does not have any knowledge about the
underlying device, a driver specific callback is required in struct
irq_affinity, which can be invoked by the core code. The callback gets the
number of available interupts as an argument, so the driver can calculate the
corresponding number and size of interrupt sets.
At the moment the struct irq_affinity pointer which is handed in from the
driver and passed through to several core functions is marked 'const', but for
the callback to be able to modify the data in the struct it's required to
remove the 'const' qualifier.
Add the optional callback to struct irq_affinity, which allows drivers to
recalculate the number and size of interrupt sets and remove the 'const'
qualifier.
For simple invocations, which do not supply a callback, a default callback
is installed, which just sets nr_sets to 1 and transfers the number of
spreadable vectors to the set_size array at index 0.
This is for now guarded by a check for nr_sets != 0 to keep the NVME driver
working until it is converted to the callback mechanism.
To make sure that the driver configuration is correct under all circumstances
the callback is invoked even when there are no interrupts for queues left,
i.e. the pre/post requirements already exhaust the numner of available
interrupts.
At the PCI layer irq_create_affinity_masks() has to be invoked even for the
case where the legacy interrupt is used. That ensures that the callback is
invoked and the device driver can adjust to that situation.
[ tglx: Fixed the simple case (no sets required). Moved the sanity check
for nr_sets after the invocation of the callback so it catches
broken drivers. Fixed the kernel doc comments for struct
irq_affinity and de-'This patch'-ed the changelog ]
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: linux-nvme@lists.infradead.org
Cc: linux-pci@vger.kernel.org
Cc: Keith Busch <keith.busch@intel.com>
Cc: Sumit Saxena <sumit.saxena@broadcom.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Shivasharan Srikanteshwara <shivasharan.srikanteshwara@broadcom.com>
Link: https://lkml.kernel.org/r/20190216172228.512444498@linutronix.de
The interrupt affinity spreading mechanism supports to spread out
affinities for one or more interrupt sets. A interrupt set contains one
or more interrupts. Each set is mapped to a specific functionality of a
device, e.g. general I/O queues and read I/O queus of multiqueue block
devices.
The number of interrupts per set is defined by the driver. It depends on
the total number of available interrupts for the device, which is
determined by the PCI capabilites and the availability of underlying CPU
resources, and the number of queues which the device provides and the
driver wants to instantiate.
The driver passes initial configuration for the interrupt allocation via
a pointer to struct irq_affinity.
Right now the allocation mechanism is complex as it requires to have a
loop in the driver to determine the maximum number of interrupts which
are provided by the PCI capabilities and the underlying CPU resources.
This loop would have to be replicated in every driver which wants to
utilize this mechanism. That's unwanted code duplication and error
prone.
In order to move this into generic facilities it is required to have a
mechanism, which allows the recalculation of the interrupt sets and
their size, in the core code. As the core code does not have any
knowledge about the underlying device, a driver specific callback will
be added to struct affinity_desc, which will be invoked by the core
code. The callback will get the number of available interupts as an
argument, so the driver can calculate the corresponding number and size
of interrupt sets.
To support this, two modifications for the handling of struct irq_affinity
are required:
1) The (optional) interrupt sets size information is contained in a
separate array of integers and struct irq_affinity contains a
pointer to it.
This is cumbersome and as the maximum number of interrupt sets is small,
there is no reason to have separate storage. Moving the size array into
struct affinity_desc avoids indirections and makes the code simpler.
2) At the moment the struct irq_affinity pointer which is handed in from
the driver and passed through to several core functions is marked
'const'.
With the upcoming callback to recalculate the number and size of
interrupt sets, it's necessary to remove the 'const'
qualifier. Otherwise the callback would not be able to update the data.
Implement #1 and store the interrupt sets size in 'struct irq_affinity'.
No functional change.
[ tglx: Fixed the memcpy() size so it won't copy beyond the size of the
source. Fixed the kernel doc comments for struct irq_affinity and
de-'This patch'-ed the changelog ]
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: linux-nvme@lists.infradead.org
Cc: linux-pci@vger.kernel.org
Cc: Keith Busch <keith.busch@intel.com>
Cc: Sumit Saxena <sumit.saxena@broadcom.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Shivasharan Srikanteshwara <shivasharan.srikanteshwara@broadcom.com>
Link: https://lkml.kernel.org/r/20190216172228.423723127@linutronix.de
All information and calculations in the interrupt affinity spreading code
is strictly unsigned int. Though the code uses int all over the place.
Convert it over to unsigned int.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: linux-nvme@lists.infradead.org
Cc: linux-pci@vger.kernel.org
Cc: Keith Busch <keith.busch@intel.com>
Cc: Sumit Saxena <sumit.saxena@broadcom.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Shivasharan Srikanteshwara <shivasharan.srikanteshwara@broadcom.com>
Link: https://lkml.kernel.org/r/20190216172228.336424556@linutronix.de
Add support for percpu_devid interrupts treated as NMIs.
Percpu_devid NMIs need to be setup/torn down on each CPU they target.
The same restrictions as for global NMIs still apply for percpu_devid NMIs.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add functionality to allocate interrupt lines that will deliver IRQs
as Non-Maskable Interrupts. These allocations are only successful if
the irqchip provides the necessary support and allows NMI delivery for the
interrupt line.
Interrupt lines allocated for NMI delivery must be enabled/disabled through
enable_nmi/disable_nmi_nosync to keep their state consistent.
To treat a PERCPU IRQ as NMI, the interrupt must not be shared nor threaded,
the irqchip directly managing the IRQ must be the root irqchip and the
irqchip cannot be behind a slow bus.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
A recent commit added a new field but did not update the kerneldoc comment,
leading to this build warning:
./include/linux/interrupt.h:268: warning: Function parameter or member 'is_managed' not described in 'irq_affinity_desc'
Add the missing information, making the docs build 0.001% quieter.
Fixes: c410abbbac ("genirq/affinity: Add is_managed to struct irq_affinity_desc")
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Dou Liyang <douliyangs@gmail.com>
Link: https://lkml.kernel.org/r/20190108170432.59bae8a6@lwn.net
Devices which use managed interrupts usually have two classes of
interrupts:
- Interrupts for multiple device queues
- Interrupts for general device management
Currently both classes are treated the same way, i.e. as managed
interrupts. The general interrupts get the default affinity mask assigned
while the device queue interrupts are spread out over the possible CPUs.
Treating the general interrupts as managed is both a limitation and under
certain circumstances a bug. Assume the following situation:
default_irq_affinity = 4..7
So if CPUs 4-7 are offlined, then the core code will shut down the device
management interrupts because the last CPU in their affinity mask went
offline.
It's also a limitation because it's desired to allow manual placement of
the general device interrupts for various reasons. If they are marked
managed then the interrupt affinity setting from both user and kernel space
is disabled. That limitation was reported by Kashyap and Sumit.
Expand struct irq_affinity_desc with a new bit 'is_managed' which is set
for truly managed interrupts (queue interrupts) and cleared for the general
device interrupts.
[ tglx: Simplify code and massage changelog ]
Reported-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reported-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Dou Liyang <douliyangs@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-pci@vger.kernel.org
Cc: shivasharan.srikanteshwara@broadcom.com
Cc: ming.lei@redhat.com
Cc: hch@lst.de
Cc: bhelgaas@google.com
Cc: douliyang1@huawei.com
Link: https://lkml.kernel.org/r/20181204155122.6327-3-douliyangs@gmail.com
The interrupt affinity management uses straight cpumask pointers to convey
the automatically assigned affinity masks for managed interrupts. The core
interrupt descriptor allocation also decides based on the pointer being non
NULL whether an interrupt is managed or not.
Devices which use managed interrupts usually have two classes of
interrupts:
- Interrupts for multiple device queues
- Interrupts for general device management
Currently both classes are treated the same way, i.e. as managed
interrupts. The general interrupts get the default affinity mask assigned
while the device queue interrupts are spread out over the possible CPUs.
Treating the general interrupts as managed is both a limitation and under
certain circumstances a bug. Assume the following situation:
default_irq_affinity = 4..7
So if CPUs 4-7 are offlined, then the core code will shut down the device
management interrupts because the last CPU in their affinity mask went
offline.
It's also a limitation because it's desired to allow manual placement of
the general device interrupts for various reasons. If they are marked
managed then the interrupt affinity setting from both user and kernel space
is disabled.
To remedy that situation it's required to convey more information than the
cpumasks through various interfaces related to interrupt descriptor
allocation.
Instead of adding yet another argument, create a new data structure
'irq_affinity_desc' which for now just contains the cpumask. This struct
can be expanded to convey auxilliary information in the next step.
No functional change, just preparatory work.
[ tglx: Simplified logic and clarified changelog ]
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Dou Liyang <douliyangs@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-pci@vger.kernel.org
Cc: kashyap.desai@broadcom.com
Cc: shivasharan.srikanteshwara@broadcom.com
Cc: sumit.saxena@broadcom.com
Cc: ming.lei@redhat.com
Cc: hch@lst.de
Cc: douliyang1@huawei.com
Link: https://lkml.kernel.org/r/20181204155122.6327-2-douliyangs@gmail.com
A driver may have a need to allocate multiple sets of MSI/MSI-X interrupts,
and have them appropriately affinitized.
Add support for defining a number of sets in the irq_affinity structure, of
varying sizes, and get each set affinitized correctly across the machine.
[ tglx: Minor changelog tweaks ]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Cc: linux-block@vger.kernel.org
Link: https://lkml.kernel.org/r/20181102145951.31979-5-ming.lei@redhat.com
Fix a grammar mistake in <linux/interrupt.h>.
[ mingo: While at it also fix another similar error in another comment as well. ]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20181008111726.26286-1-geert%2Brenesas@glider.be
Signed-off-by: Ingo Molnar <mingo@kernel.org>
s390 is now the last architecture that entirely overwrites
local_softirq_pending() and uses the according default definitions of
set_softirq_pending() and or_softirq_pending().
Just move these to s390 to debloat the generic code complexity.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/1525786706-22846-12-git-send-email-frederic@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Consolidate and optimize default softirq mask API implementations.
Per-CPU operations are expected to be faster and a few architectures
already rely on them to implement local_softirq_pending() and related
accessors/mutators. Those will be migrated to the new generic code.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/1525786706-22846-6-git-send-email-frederic@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It seems that <linux/interrupt.h> does not need <linux/linkage.h>
nor <linux/preempt.h>. 8 kernels builds are successful without
these 2 headers (allmodconfig, allyesconfig, allnoconfig, and
tinyconfig on both i386 and x86_64).
<linux/interrupt.h> is #included 3875 times in 4.16-rc1, so this
reduces #include processing of these 2 files by a total of 7750 times.
Since I only tested x86 builds, this needs to be tested on other
$ARCHes as well.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Link: http://lkml.kernel.org/r/b24b9ec8-4970-65f5-759a-911d4ba2fcf0@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds
Thomas Gleixner
Sebastian Andrzej Siewior
Frederic Weisbecker
Tanner Love
Peter Zijlstra
Davidlohr Bueso
Barry Song
John Garry
Joe Perches
Romain Perier
Kees Cook
Jonathan Corbet
Rafael J. Wysocki
Mauro Carvalho Chehab
Ming Lei
Julien Thierry
Dou Liyang
Jens Axboe
Geert Uytterhoeven
Randy Dunlap