Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening in
the driver core in the quest to be able to move "struct bus" and "struct
class" into read-only memory, a task now complete with these changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules for
all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most of
them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEp7Sw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykitQCfamUHpxGcKOAGuLXMotXNakTEsxgAoIquENm5
LEGadNS38k5fs+73UaxV
=7K4B
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening
in the driver core in the quest to be able to move "struct bus" and
"struct class" into read-only memory, a task now complete with these
changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules
for all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most
of them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (120 commits)
device property: make device_property functions take const device *
driver core: update comments in device_rename()
driver core: Don't require dynamic_debug for initcall_debug probe timing
firmware_loader: rework crypto dependencies
firmware_loader: Strip off \n from customized path
zram: fix up permission for the hot_add sysfs file
cacheinfo: Add use_arch[|_cache]_info field/function
arch_topology: Remove early cacheinfo error message if -ENOENT
cacheinfo: Check cache properties are present in DT
cacheinfo: Check sib_leaf in cache_leaves_are_shared()
cacheinfo: Allow early level detection when DT/ACPI info is missing/broken
cacheinfo: Add arm64 early level initializer implementation
cacheinfo: Add arch specific early level initializer
tty: make tty_class a static const structure
driver core: class: remove struct class_interface * from callbacks
driver core: class: mark the struct class in struct class_interface constant
driver core: class: make class_register() take a const *
driver core: class: mark class_release() as taking a const *
driver core: remove incorrect comment for device_create*
MIPS: vpe-cmp: remove module owner pointer from struct class usage.
...
We need the fixes in here for testing, as well as the driver core
changes for documentation updates to build on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* TC offload support for drivers below mac80211
* reduced neighbor report (RNR) handling for AP mode
* mac80211 mesh fast-xmit and fast-rx support
* support for another mesh A-MSDU format
(seems nobody got the spec right)
Major driver changes:
Kalle moved the drivers that were just plain C files
in drivers/net/wireless/ to legacy/ and virtual/ dirs.
hwsim
* multi-BSSID support
* some FTM support
ath11k
* MU-MIMO parameters support
* ack signal support for management packets
rtl8xxxu
* support for RTL8710BU aka RTL8188GU chips
rtw89
* support for various newer firmware APIs
ath10k
* enabled threaded NAPI on WCN3990
iwlwifi
* lots of work for multi-link/EHT (wifi7)
* hardware timestamping support for some devices/firwmares
* TX beacon protection on newer hardware
-----BEGIN PGP SIGNATURE-----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=Zi6X
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2023-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Major stack changes:
* TC offload support for drivers below mac80211
* reduced neighbor report (RNR) handling for AP mode
* mac80211 mesh fast-xmit and fast-rx support
* support for another mesh A-MSDU format
(seems nobody got the spec right)
Major driver changes:
Kalle moved the drivers that were just plain C files
in drivers/net/wireless/ to legacy/ and virtual/ dirs.
hwsim
* multi-BSSID support
* some FTM support
ath11k
* MU-MIMO parameters support
* ack signal support for management packets
rtl8xxxu
* support for RTL8710BU aka RTL8188GU chips
rtw89
* support for various newer firmware APIs
ath10k
* enabled threaded NAPI on WCN3990
iwlwifi
* lots of work for multi-link/EHT (wifi7)
* hardware timestamping support for some devices/firwmares
* TX beacon protection on newer hardware
* tag 'wireless-next-2023-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (181 commits)
wifi: clean up erroneously introduced file
wifi: iwlwifi: mvm: correctly use link in iwl_mvm_sta_del()
wifi: iwlwifi: separate AP link management queues
wifi: iwlwifi: mvm: free probe_resp_data later
wifi: iwlwifi: bump FW API to 75 for AX devices
wifi: iwlwifi: mvm: move max_agg_bufsize into host TLC lq_sta
wifi: iwlwifi: mvm: send full STA during HW restart
wifi: iwlwifi: mvm: rework active links counting
wifi: iwlwifi: mvm: update mac config when assigning chanctx
wifi: iwlwifi: mvm: use the correct link queue
wifi: iwlwifi: mvm: clean up mac_id vs. link_id in MLD sta
wifi: iwlwifi: mvm: fix station link data leak
wifi: iwlwifi: mvm: initialize max_rc_amsdu_len per-link
wifi: iwlwifi: mvm: use appropriate link for rate selection
wifi: iwlwifi: mvm: use the new lockdep-checking macros
wifi: iwlwifi: mvm: remove chanctx WARN_ON
wifi: iwlwifi: mvm: avoid sending MAC context for idle
wifi: iwlwifi: mvm: remove only link-specific AP keys
wifi: iwlwifi: mvm: skip inactive links
wifi: iwlwifi: mvm: adjust iwl_mvm_scan_respect_p2p_go_iter() for MLO
...
====================
Link: https://lore.kernel.org/r/20230330205612.921134-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Expose nl80211_send_chandef functionality for mac80211_hwsim or vendor
netlink can use it where needed.
Signed-off-by: Jaewan Kim <jaewan@google.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://lore.kernel.org/r/20230322131637.2633968-3-jaewan@google.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As per IEEE Std 802.11ax-2021, 11.1.3.8.3 Discovery of a nontransmitted
BSSID profile, an EMA AP that transmits a Beacon frame carrying a partial
list of nontransmitted BSSID profiles should include in the frame
a Reduced Neighbor Report element carrying information for at least the
nontransmitted BSSIDs that are not present in the Multiple BSSID element
carried in that frame.
Add new nested attribute NL80211_ATTR_EMA_RNR_ELEMS to support the above.
Number of RNR elements must be more than or equal to the number of
MBSSID elements. This attribute can be used only when EMA is enabled.
Userspace is responsible for splitting the RNR into multiple elements such
that each element excludes the non-transmitting profiles already included
in the MBSSID element (%NL80211_ATTR_MBSSID_ELEMS) at the same index.
Each EMA beacon will be generated by adding MBSSID and RNR elements
at the same index. If the userspace provides more RNR elements than the
number of MBSSID elements then these will be added in every EMA beacon.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Link: https://lore.kernel.org/r/20230323113801.6903-2-quic_alokad@quicinc.com
[Johannes: validate elements]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
MT7996 hardware supports mesh A-MSDU subframes in hardware, but uses a
big-endian length field
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Link: https://lore.kernel.org/r/20230314095956.62085-7-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Current release - regressions:
- phy: mscc: fix deadlock in phy_ethtool_{get,set}_wol()
- virtio: vsock: don't use skbuff state to account credit
- virtio: vsock: don't drop skbuff on copy failure
- virtio_net: fix page_to_skb() miscalculating the memory size
Current release - new code bugs:
- eth: correct xdp_features after device reconfig
- wifi: nl80211: fix the puncturing bitmap policy
- net/mlx5e: flower:
- fix raw counter initialization
- fix missing error code
- fix cloned flow attribute
- ipa:
- fix some register validity checks
- fix a surprising number of bad offsets
- kill FILT_ROUT_CACHE_CFG IPA register
Previous releases - regressions:
- tcp: fix bind() conflict check for dual-stack wildcard address
- veth: fix use after free in XDP_REDIRECT when skb headroom is small
- ipv4: fix incorrect table ID in IOCTL path
- ipvlan: make skb->skb_iif track skb->dev for l3s mode
- mptcp:
- fix possible deadlock in subflow_error_report
- fix UaFs when destroying unaccepted and listening sockets
- dsa: mv88e6xxx: fix max_mtu of 1492 on 6165, 6191, 6220, 6250, 6290
Previous releases - always broken:
- tcp: tcp_make_synack() can be called from process context,
don't assume preemption is disabled when updating stats
- netfilter: correct length for loading protocol registers
- virtio_net: add checking sq is full inside xdp xmit
- bonding: restore IFF_MASTER/SLAVE flags on bond enslave
Ethertype change
- phy: nxp-c45-tja11xx: fix MII_BASIC_CONFIG_REV bit number
- eth: i40e: fix crash during reboot when adapter is in recovery mode
- eth: ice: avoid deadlock on rtnl lock when auxiliary device
plug/unplug meets bonding
- dsa: mt7530:
- remove now incorrect comment regarding port 5
- set PLL frequency and trgmii only when trgmii is used
- eth: mtk_eth_soc: reset PCS state when changing interface types
Misc:
- ynl: another license adjustment
- move the TCA_EXT_WARN_MSG attribute for tc action
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=5/YI
-----END PGP SIGNATURE-----
Merge tag 'net-6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter, wifi and ipsec.
A little more changes than usual, but it's pretty normal for us that
the rc3/rc4 PRs are oversized as people start testing in earnest.
Possibly an extra boost from people deploying the 6.1 LTS but that's
more of an unscientific hunch.
Current release - regressions:
- phy: mscc: fix deadlock in phy_ethtool_{get,set}_wol()
- virtio: vsock: don't use skbuff state to account credit
- virtio: vsock: don't drop skbuff on copy failure
- virtio_net: fix page_to_skb() miscalculating the memory size
Current release - new code bugs:
- eth: correct xdp_features after device reconfig
- wifi: nl80211: fix the puncturing bitmap policy
- net/mlx5e: flower:
- fix raw counter initialization
- fix missing error code
- fix cloned flow attribute
- ipa:
- fix some register validity checks
- fix a surprising number of bad offsets
- kill FILT_ROUT_CACHE_CFG IPA register
Previous releases - regressions:
- tcp: fix bind() conflict check for dual-stack wildcard address
- veth: fix use after free in XDP_REDIRECT when skb headroom is small
- ipv4: fix incorrect table ID in IOCTL path
- ipvlan: make skb->skb_iif track skb->dev for l3s mode
- mptcp:
- fix possible deadlock in subflow_error_report
- fix UaFs when destroying unaccepted and listening sockets
- dsa: mv88e6xxx: fix max_mtu of 1492 on 6165, 6191, 6220, 6250, 6290
Previous releases - always broken:
- tcp: tcp_make_synack() can be called from process context, don't
assume preemption is disabled when updating stats
- netfilter: correct length for loading protocol registers
- virtio_net: add checking sq is full inside xdp xmit
- bonding: restore IFF_MASTER/SLAVE flags on bond enslave Ethertype
change
- phy: nxp-c45-tja11xx: fix MII_BASIC_CONFIG_REV bit number
- eth: i40e: fix crash during reboot when adapter is in recovery mode
- eth: ice: avoid deadlock on rtnl lock when auxiliary device
plug/unplug meets bonding
- dsa: mt7530:
- remove now incorrect comment regarding port 5
- set PLL frequency and trgmii only when trgmii is used
- eth: mtk_eth_soc: reset PCS state when changing interface types
Misc:
- ynl: another license adjustment
- move the TCA_EXT_WARN_MSG attribute for tc action"
* tag 'net-6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (108 commits)
selftests: bonding: add tests for ether type changes
bonding: restore bond's IFF_SLAVE flag if a non-eth dev enslave fails
bonding: restore IFF_MASTER/SLAVE flags on bond enslave ether type change
net: renesas: rswitch: Fix GWTSDIE register handling
net: renesas: rswitch: Fix the output value of quote from rswitch_rx()
ethernet: sun: add check for the mdesc_grab()
net: ipa: fix some register validity checks
net: ipa: kill FILT_ROUT_CACHE_CFG IPA register
net: ipa: add two missing declarations
net: ipa: reg: include <linux/bug.h>
net: xdp: don't call notifiers during driver init
net/sched: act_api: add specific EXT_WARN_MSG for tc action
Revert "net/sched: act_api: move TCA_EXT_WARN_MSG to the correct hierarchy"
net: dsa: microchip: fix RGMII delay configuration on KSZ8765/KSZ8794/KSZ8795
ynl: make the tooling check the license
ynl: broaden the license even more
tools: ynl: make definitions optional again
hsr: ratelimit only when errors are printed
qed/qed_mng_tlv: correctly zero out ->min instead of ->hour
selftests: net: devlink_port_split.py: skip test if no suitable device available
...
There is no need to manually set the owner of a struct class, as the
registering function does it automatically, so remove all of the
explicit settings from various drivers that did so as it is unneeded.
This allows us to remove this pointer entirely from this structure going
forward.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Link: https://lore.kernel.org/r/20230313181843.1207845-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts part of commit 015b8cc5e7 ("wifi: cfg80211: Fix use after
free for wext")
This commit broke WPA offload by unconditionally clearing the crypto
modes for non-WEP connections. Drop that part of the patch.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reported-by: Ilya <me@0upti.me>
Reported-and-tested-by: Janne Grunau <j@jannau.net>
Reviewed-by: Eric Curtin <ecurtin@redhat.com>
Fixes: 015b8cc5e7 ("wifi: cfg80211: Fix use after free for wext")
Cc: stable@kernel.org
Link: https://lore.kernel.org/linux-wireless/ZAx0TWRBlGfv7pNl@kroah.com/T/#m11e6e0915ab8fa19ce8bc9695ab288c0fe018edf
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Major changes:
cfg80211
* 6 GHz improvements
* HW timestamping support
* support for randomized auth/deauth TA for PASN privacy
(also for mac80211)
mac80211
* radiotap TLV and EHT support for the iwlwifi sniffer
* HW timestamping support
* per-link debugfs for multi-link
brcmfmac
* support for Apple (M1 Pro/Max) devices
iwlwifi
* support for a few new devices
* EHT sniffer support
rtw88
* better support for some SDIO devices
(e.g. MAC address from efuse)
rtw89
* HW scan support for 8852b
* better support for 6 GHz scanning
-----BEGIN PGP SIGNATURE-----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=sPir
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2023-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
wireless-next patches for 6.4
Major changes:
cfg80211
* 6 GHz improvements
* HW timestamping support
* support for randomized auth/deauth TA for PASN privacy
(also for mac80211)
mac80211
* radiotap TLV and EHT support for the iwlwifi sniffer
* HW timestamping support
* per-link debugfs for multi-link
brcmfmac
* support for Apple (M1 Pro/Max) devices
iwlwifi
* support for a few new devices
* EHT sniffer support
rtw88
* better support for some SDIO devices
(e.g. MAC address from efuse)
rtw89
* HW scan support for 8852b
* better support for 6 GHz scanning
* tag 'wireless-next-2023-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (84 commits)
wifi: iwlwifi: mvm: fix EOF bit reporting
wifi: iwlwifi: Do not include radiotap EHT user info if not needed
wifi: iwlwifi: mvm: add EHT RU allocation to radiotap
wifi: iwlwifi: Update logs for yoyo reset sw changes
wifi: iwlwifi: mvm: clean up duplicated defines
wifi: iwlwifi: rs-fw: break out for unsupported bandwidth
wifi: iwlwifi: Add support for B step of BnJ-Fm4
wifi: iwlwifi: mvm: make flush code a bit clearer
wifi: iwlwifi: mvm: avoid UB shift of snif_queue
wifi: iwlwifi: mvm: add primary 80 known for EHT radiotap
wifi: iwlwifi: mvm: parse FW frame metadata for EHT sniffer mode
wifi: iwlwifi: mvm: decode USIG_B1_B7 RU to nl80211 RU width
wifi: iwlwifi: mvm: rename define to generic name
wifi: iwlwifi: mvm: allow Microsoft to use TAS
wifi: iwlwifi: mvm: add all EHT based on data0 info from HW
wifi: iwlwifi: mvm: add EHT radiotap info based on rate_n_flags
wifi: iwlwifi: mvm: add an helper function radiotap TLVs
wifi: radiotap: separate vendor TLV into header/content
wifi: iwlwifi: reduce verbosity of some logging events
wifi: iwlwifi: Adding the code to get RF name for MsP device
...
====================
Link: https://lore.kernel.org/r/20230310120159.36518-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When disconnecting from an MLO connection we need the AP
MLD address, not an arbitrary BSSID. Fix the code to do
that.
Fixes: 9ecff10e82 ("wifi: nl80211: refactor BSS lookup in nl80211_associate()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230301115906.4c1b3b18980e.I008f070c7f3b8e8bde9278101ef9e40706a82902@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This was meant to be a u32, and while applying the patch
I tried to use policy validation for it. However, not only
did I copy/paste it to u8 instead of u32, but also used
the policy range erroneously. Fix both of these issues.
Fixes: d7c1a9a0ed ("wifi: nl80211: validate and configure puncturing bitmap")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If, e.g. in AP mode, the link was already created by userspace
but not activated yet, it has a chandef but the chandef isn't
valid and has no channel. Check for this and ignore this link.
Fixes: 7b0a0e3c3a ("wifi: cfg80211: do some rework towards MLO link APIs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230301115906.71bd4803fbb9.Iee39c0f6c2d3a59a8227674dc55d52e38b1090cf@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The cfg80211_scan_request structure is followed by a flexible array member
as well as several other arrays that are then stored into pointers in the
structure. These are allocated currently using a simple sequence of
multiplications.
Replace the calculations with struct_size(), size_add(), and array_size()
helper macros. These macros saturate the calculation at SIZE_MAX rather
than overflowing.
Note that we can't use flex_array_size() instead of array_size() because
the fields are not arrays, but simple pointers.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230228162827.3876606-3-jacob.e.keller@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support to use a random local address in authentication and
deauthentication frames sent to unassociated peer when the driver
supports.
The driver needs to configure receive behavior to accept frames with
random transmit address specified in TX path authentication frames
during the time of the frame exchange is pending and such frames need to
be acknowledged similarly to frames sent to the local permanent address
when this random address functionality is used.
This capability allows use of randomized transmit address for PASN
authentication frames to improve privacy of WLAN clients.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Link: https://lore.kernel.org/r/20230112012415.167556-2-quic_vjakkam@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a command to enable and disable HW timestamping of TM and FTM
frames. HW timestamping can be enabled for a specific mac address
or for all addresses.
The low level driver will indicate how many peers HW timestamping
can be enabled concurrently, and this information will be passed
to userspace.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230301115906.05678d7b1c17.Iccc08869ea8156f1c71a3111a47f86dd56234bd0@changeid
[switch to needing netdev UP, minor edits]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The check that beacon primary channel is in the range of 80 MHz
(abs < 80) is invalid for 320 MHz since duplicate beacon transmit
means that the AP transmits it on all the 20 MHz sub-channels:
9.4.2.249 HE Operation element - ... AP transmits Beacon frames in
non-HT duplicate PPDU with a TXVECTOR parameter CH_BANDWIDTH value
that is up to the BSS bandwidth.
So in case of 320 MHz the DUP beacon can be in upper 160 for primary
channel in the lower 160 giving possibly an absolute range of over
80 MHz.
Also this check is redundant alltogether, if AP has a wrong primary
channel in the beacon it's a faulty AP, and we would fail in next
steps to connect.
While at it, fix the frequency comparison to no longer compare
between KHz and MHz, which was introduced by commit 7f599aeccb
("cfg80211: Use the HE operation IE to determine a 6GHz BSS channel").
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230301115906.314faf725255.I5e27251ac558297553b590d3917a7b6d1aae0e74@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently in case DUP bit is not set we don't return the primary
channel for 6 GHz Band, but the spec says that the DUP bit has
no effect on this field:
9.4.2.249 HE Operation element:
The Duplicate Beacon subfield is set to 1 if the AP transmits
Beacon frames in non-HT duplicate PPDU with a TXVECTOR parameter
CH_BANDWIDTH value that is up to the BSS bandwidth and is set to
0 otherwise.
So remove the condition for returning primary channel based on DUP.
Since the caller code already marks the signal as invalid in case
the indicated frequency is not the tuned frequency, there's no need
to additionally handle this case here since that's already true for
duplicated beacons on the non-primary channel(s).
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230301115906.66d7f05f7d11.I5e0add054f72ede95611391b99804c61c40cc959@changeid
[clarify commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Warn only once since the ratelimit parameters are still
allowing too many messages to happen. This will no longer
tell you all the different processes, but still gives a
heads-up of sorts.
Also modify the message to note that wext stops working
for future Wi-Fi 7 hardware, this is already implemented
in commit 4ca6902769 ("wifi: wireless: deny wireless
extensions on MLO-capable devices") and is maybe of more
relevance to users than the fact that we'd like to have
wireless extensions deprecated.
The issue with Wi-Fi 7 is that you can now have multiple
connections to the same AP, so a whole bunch of things
now become per link rather than per netdev, which can't
really be handled in wireless extensions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230224135933.94104aeda1a0.Ie771c6a66d7d6c3cf67da5f3b0c66cea66fd514c@changeid
When a connection was established without going through
NL80211_CMD_CONNECT, the ssid was never set in the wireless_dev struct.
Now we set it in __cfg80211_connect_result() when it is not already set.
When using a userspace configuration that does not call
cfg80211_connect() (can be checked with breakpoints in the kernel),
this patch should allow `networkctl status device_name` to output the
SSID instead of null.
Cc: stable@vger.kernel.org
Reported-by: Yohan Prod'homme <kernel@zoddo.fr>
Fixes: 7b0a0e3c3a (wifi: cfg80211: do some rework towards MLO link APIs)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216711
Signed-off-by: Marc Bornand <dev.mbornand@systemb.ch>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the regulatory driver does not call the regulatory callback
reg_notifier for self managed wiphys. Sometimes driver needs cfg80211
to calculate the info of ieee80211_channel such as flags and power,
and driver needs to get the info of ieee80211_channel after hint of
driver, but driver does not know when calculation of the info of
ieee80211_channel become finished, so add notify to driver in
reg_process_self_managed_hint() from cfg80211 is a good way, then
driver could get the correct info in callback of reg_notifier.
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Link: https://lore.kernel.org/r/20230201065313.27203-1-quic_wgong@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Wi-Fi Aware R4 specification defines NAN Pairing which uses PASN handshake
to authenticate the peer and generate keys. Hence allow to register and transmit
the PASN authentication frames on NAN interface and set the keys to driver or
underlying modules on NAN interface.
The driver needs to configure the feature flag NL80211_EXT_FEATURE_SECURE_NAN,
which also helps userspace modules to know if the driver supports secure NAN.
Signed-off-by: Vinay Gannevaram <quic_vganneva@quicinc.com>
Link: https://lore.kernel.org/r/1675519179-24174-1-git-send-email-quic_vganneva@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At least ath10k and ath11k supported hardware (maybe more) does not implement
mesh A-MSDU aggregation in a standard compliant way.
802.11-2020 9.3.2.2.2 declares that the Mesh Control field is part of the
A-MSDU header (and little-endian).
As such, its length must not be included in the subframe length field.
Hardware affected by this bug treats the mesh control field as part of the
MSDU data and sets the length accordingly.
In order to avoid packet loss, keep track of which stations are affected
by this and take it into account when converting A-MSDU to 802.3 + mesh control
packets.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230213100855.34315-5-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current mac80211 mesh A-MSDU receive path fails to parse A-MSDU packets
on mesh interfaces, because it assumes that the Mesh Control field is always
directly after the 802.11 header.
802.11-2020 9.3.2.2.2 Figure 9-70 shows that the Mesh Control field is
actually part of the A-MSDU subframe header.
This makes more sense, since it allows packets for multiple different
destinations to be included in the same A-MSDU, as long as RA and TID are
still the same.
Another issue is the fact that the A-MSDU subframe length field was apparently
accidentally defined as little-endian in the standard.
In order to fix this, the mesh forwarding path needs happen at a different
point in the receive path.
ieee80211_data_to_8023_exthdr is changed to ignore the mesh control field
and leave it in after the ethernet header. This also affects the source/dest
MAC address fields, which now in the case of mesh point to the mesh SA/DA.
ieee80211_amsdu_to_8023s is changed to deal with the endian difference and
to add the Mesh Control length to the subframe length, since it's not covered
by the MSDU length field.
With these changes, the mac80211 will get the same packet structure for
converted regular data packets and unpacked A-MSDU subframes.
The mesh forwarding checks are now only performed after the A-MSDU decap.
For locally received packets, the Mesh Control header is stripped away.
For forwarded packets, a new 802.11 header gets added.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230213100855.34315-4-nbd@nbd.name
[fix fortify build error]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When parsing the outer A-MSDU header, don't check for inner bridge tunnel
or RFC1042 headers. This is handled by ieee80211_amsdu_to_8023s already.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230213100855.34315-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently action frames TX only with ML address as A3(BSSID) are
allowed in an ML AP, but TX for a non-ML Station can happen in any
link of an ML BSS with link BSS address as A3.
In case of an MLD, if User-space has provided a valid link_id in
action frame TX request, allow transmission of the frame in that link.
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://lore.kernel.org/r/20230201061602.3918-1-quic_ramess@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- New feature flag, NL80211_EXT_FEATURE_PUNCT, to advertise
driver support for preamble puncturing in AP mode.
- New attribute, NL80211_ATTR_PUNCT_BITMAP, to receive a puncturing
bitmap from the userspace during AP bring up (NL80211_CMD_START_AP)
and channel switch (NL80211_CMD_CHANNEL_SWITCH) operations. Each bit
corresponds to a 20 MHz channel in the operating bandwidth, lowest
bit for the lowest channel. Bit set to 1 indicates that the channel
is punctured. Higher 16 bits are reserved.
- New members added to structures cfg80211_ap_settings and
cfg80211_csa_settings to propagate the bitmap to the driver after
validation.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Link: https://lore.kernel.org/r/20230131001227.25014-3-quic_alokad@quicinc.com
[move validation against 0xffff into policy]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- Move ieee80211_valid_disable_subchannel_bitmap() from mlme.c to
chan.c, rename it as cfg80211_valid_disable_subchannel_bitmap()
and export it.
- Modify the prototype to include struct cfg80211_chan_def instead
of only bandwidth to support a check which returns false if the
primary channel is punctured.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Link: https://lore.kernel.org/r/20230131001227.25014-2-quic_alokad@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add an error message to the missing frequency case to have all
-EINVAL in nl80211_parse_chandef() return a better error.
Signed-off-by: Jaewan Kim <jaewan@google.com>
Link: https://lore.kernel.org/r/20230130074514.1560021-1-jaewan@google.com
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
nl80211_send_ap_stopped() can be called multiple times on the same
netdev for each link when using Multi-Link Operation. Add the
MLO_LINK_ID attribute to the event to allow userspace to distinguish
which link the event is for.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Link: https://lore.kernel.org/r/20230128125844.2407135-2-alvin@pqrs.dk
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Userspace processes such as network daemons may wish to be informed when
any AP interface is brought up on the system, for example to initiate a
(re)configuration of IP settings or to start a DHCP server.
Currently nl80211 does not broadcast any such event on its multicast
groups, leaving userspace only two options:
1. the process must be the one that actually issued the
NL80211_CMD_START_AP request, so that it can react on the response to
that request;
2. the process must react to RTM_NEWLINK events indicating a change in
carrier state, and may query for further information about the AP and
react accordingly.
Option (1) is robust, but it does not cover all scenarios. It is easy to
imagine a situation where this is not the case (e.g. hostapd +
systemd-networkd).
Option (2) is not robust, because RTM_NEWLINK events may be silently
discarded by the linkwatch logic (cf. linkwatch_fire_event()).
Concretely, consider a scenario in which the carrier state flip-flops in
the following way:
^ carrier state (high/low = carrier/no carrier)
|
| _______ _______ ...
| | | |
| ______| "foo" |____| "bar" (SSID in "quotes")
|
+-------A-------B----C---------> time
If the time interval between (A) and (C) is less than 1 second, then
linkwatch may emit only a single RTM_NEWLINK event indicating carrier
gain.
This is problematic because it is possible that the network
configuration that should be applied is a function of the AP's
properties such as SSID (cf. SSID= in systemd.network(5)). As
illustrated in the above diagram, it may be that the AP with SSID "bar"
ends up being configured as though it had SSID "foo".
Address the above issue by having nl80211 emit an NL80211_CMD_START_AP
message on the MLME nl80211 multicast group. This allows for arbitrary
processes to be reliably informed.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Link: https://lore.kernel.org/r/20230128125844.2407135-1-alvin@pqrs.dk
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support to offload OWE processing to user space for MLD AP when
driver's SME in use.
Add new parameters in struct cfg80211_update_owe_info to provide below
information in cfg80211_update_owe_info_event() call:
- MLO link ID of the AP, with which station requested (re)association.
This is applicable for both MLO and non-MLO station connections when
the AP affiliated with an MLD.
- Station's MLD address if the connection is MLO capable.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Link: https://lore.kernel.org/r/20230126143256.960563-3-quic_vjakkam@quicinc.com
[reformat the trace event macro]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for drivers to indicate STA connection(MLO/non-MLO) when
user space SME (e.g., hostapd) is not used for MLD AP.
Add new parameters in struct station_info to provide below information
in cfg80211_new_sta() call:
- MLO link ID of the AP, with which station completed (re)association.
This is applicable for both MLO and non-MLO station connections when
the AP affiliated with an MLD.
- Station's MLD address if the connection is MLO capable.
- (Re)Association Response IEs sent to the station. User space needs
this to determine rejected and accepted affiliated links information
of the connected station if the connection is MLO capable.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Link: https://lore.kernel.org/r/20230126143256.960563-2-quic_vjakkam@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Key information in wext.connect is not reset on (re)connect and can hold
data from a previous connection.
Reset key data to avoid that drivers or mac80211 incorrectly detect a
WEP connection request and access the freed or already reused memory.
Additionally optimize cfg80211_sme_connect() and avoid an useless
schedule of conn_work.
Fixes: fffd0934b9 ("cfg80211: rework key operation")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230124141856.356646-1-alexander@wetzel-home.de
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently authentication request event interface doesn't have support to
indicate the user space whether it should enable MLO or not during the
authentication with the specified AP. But driver needs such capability
since the connection is MLO or not decided by the driver in case of SME
offload to the driver.
Add support for driver to indicate MLD address of the AP in
authentication offload request to inform user space to enable MLO during
authentication process. Driver shall look at NL80211_ATTR_MLO_SUPPORT
flag capability in NL80211_CMD_CONNECT to know whether the user space
supports enabling MLO during the authentication offload.
User space should enable MLO during the authentication only when it
receives the AP MLD address in authentication offload request. User
space shouldn't enable MLO if the authentication offload request doesn't
indicate the AP MLD address even if the AP is MLO capable.
When MLO is enabled, user space should use the MAC address of the
interface (on which driver sent request) as self MLD address. User space
and driver to use MLD addresses in RA, TA and BSSID fields of the frames
between them, and driver translates the MLD addresses to/from link
addresses based on the link chosen for the authentication.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Link: https://lore.kernel.org/r/20230116125058.1604843-1-quic_vjakkam@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These are WiFi 7 devices that will be introduced into the market
in 2023, with new drivers. Wireless extensions haven't been in
real development since 2006. Since wireless has evolved a lot,
and continues to evolve significantly with Multi-Link Operation,
there's really no good way to still support wireless extensions
for devices that do MLO.
Stop supporting wireless extensions for new devices. We don't
consider this a regression since no such devices (apart from
hwsim) exist yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230118105152.45f85078a1e0.Ib9eabc2ec5bf6b0244e4d973e93baaa3d8c91bd8@changeid
With WiFi 7 (802.11ax, MLO/EHT) around the corner, we're going to
remove support for wireless extensions with new devices since MLO
(multi-link operation) cannot be properly indicated using them.
Add a warning to indicate which processes are still using wireless
extensions, if being used with modern (i.e. cfg80211) drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230118105152.a7158a929a6f.Ifcf30eeeb8fc7019e4dcf2782b04515254d165e1@changeid
load_keys_from_buffer() in net/wireless/reg.c duplicates
x509_load_certificate_list() in crypto/asymmetric_keys/x509_loader.c
for no apparent reason.
Deduplicate it. No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: David Howells <dhowells@redhat.com>
Link: https://lore.kernel.org/r/e7280be84acda02634bc7cb52c97656182b9c700.1673197326.git.lukas@wunner.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, maximum KCK key length supported for GTK rekey offload is 24
bytes but with some newer AKMs the KCK key length can be 32 bytes. e.g.,
00-0F-AC:24 AKM suite with SAE finite cyclic group 21. Add support to
allow 32 bytes KCK keys in GTK rekey offload.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Link: https://lore.kernel.org/r/20221206143715.1802987-3-quic_vjakkam@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The extended KCK key length check wrongly using the KEK key attribute
for validation. Due to this GTK rekey offload is failing when the KCK
key length is 24 bytes even though the driver advertising
WIPHY_FLAG_SUPPORTS_EXT_KEK_KCK flag. Use correct attribute to fix the
same.
Fixes: 093a48d2aa ("cfg80211: support bigger kek/kck key length")
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Link: https://lore.kernel.org/r/20221206143715.1802987-2-quic_vjakkam@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit b8676221f0 ("cfg80211: Add support for
static WEP in the driver") since no driver ever ended up using
it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Here is the set of driver core and kernfs changes for 6.2-rc1.
The "big" change in here is the addition of a new macro,
container_of_const() that will preserve the "const-ness" of a pointer
passed into it.
The "problem" of the current container_of() macro is that if you pass in
a "const *", out of it can comes a non-const pointer unless you
specifically ask for it. For many usages, we want to preserve the
"const" attribute by using the same call. For a specific example, this
series changes the kobj_to_dev() macro to use it, allowing it to be used
no matter what the const value is. This prevents every subsystem from
having to declare 2 different individual macros (i.e.
kobj_const_to_dev() and kobj_to_dev()) and having the compiler enforce
the const value at build time, which having 2 macros would not do
either.
The driver for all of this have been discussions with the Rust kernel
developers as to how to properly mark driver core, and kobject, objects
as being "non-mutable". The changes to the kobject and driver core in
this pull request are the result of that, as there are lots of paths
where kobjects and device pointers are not modified at all, so marking
them as "const" allows the compiler to enforce this.
So, a nice side affect of the Rust development effort has been already
to clean up the driver core code to be more obvious about object rules.
All of this has been bike-shedded in quite a lot of detail on lkml with
different names and implementations resulting in the tiny version we
have in here, much better than my original proposal. Lots of subsystem
maintainers have acked the changes as well.
Other than this change, included in here are smaller stuff like:
- kernfs fixes and updates to handle lock contention better
- vmlinux.lds.h fixes and updates
- sysfs and debugfs documentation updates
- device property updates
All of these have been in the linux-next tree for quite a while with no
problems, OTHER than some merge issues with other trees that should be
obvious when you hit them (block tree deletes a driver that this tree
modifies, iommufd tree modifies code that this tree also touches). If
there are merge problems with these trees, please let me know.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY5wz3A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yks0ACeKYUlVgCsER8eYW+x18szFa2QTXgAn2h/VhZe
1Fp53boFaQkGBjl8mGF8
=v+FB
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of driver core and kernfs changes for 6.2-rc1.
The "big" change in here is the addition of a new macro,
container_of_const() that will preserve the "const-ness" of a pointer
passed into it.
The "problem" of the current container_of() macro is that if you pass
in a "const *", out of it can comes a non-const pointer unless you
specifically ask for it. For many usages, we want to preserve the
"const" attribute by using the same call. For a specific example, this
series changes the kobj_to_dev() macro to use it, allowing it to be
used no matter what the const value is. This prevents every subsystem
from having to declare 2 different individual macros (i.e.
kobj_const_to_dev() and kobj_to_dev()) and having the compiler enforce
the const value at build time, which having 2 macros would not do
either.
The driver for all of this have been discussions with the Rust kernel
developers as to how to properly mark driver core, and kobject,
objects as being "non-mutable". The changes to the kobject and driver
core in this pull request are the result of that, as there are lots of
paths where kobjects and device pointers are not modified at all, so
marking them as "const" allows the compiler to enforce this.
So, a nice side affect of the Rust development effort has been already
to clean up the driver core code to be more obvious about object
rules.
All of this has been bike-shedded in quite a lot of detail on lkml
with different names and implementations resulting in the tiny version
we have in here, much better than my original proposal. Lots of
subsystem maintainers have acked the changes as well.
Other than this change, included in here are smaller stuff like:
- kernfs fixes and updates to handle lock contention better
- vmlinux.lds.h fixes and updates
- sysfs and debugfs documentation updates
- device property updates
All of these have been in the linux-next tree for quite a while with
no problems"
* tag 'driver-core-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (58 commits)
device property: Fix documentation for fwnode_get_next_parent()
firmware_loader: fix up to_fw_sysfs() to preserve const
usb.h: take advantage of container_of_const()
device.h: move kobj_to_dev() to use container_of_const()
container_of: add container_of_const() that preserves const-ness of the pointer
driver core: fix up missed drivers/s390/char/hmcdrv_dev.c class.devnode() conversion.
driver core: fix up missed scsi/cxlflash class.devnode() conversion.
driver core: fix up some missing class.devnode() conversions.
driver core: make struct class.devnode() take a const *
driver core: make struct class.dev_uevent() take a const *
cacheinfo: Remove of_node_put() for fw_token
device property: Add a blank line in Kconfig of tests
device property: Rename goto label to be more precise
device property: Move PROPERTY_ENTRY_BOOL() a bit down
device property: Get rid of __PROPERTY_ENTRY_ARRAY_EL*SIZE*()
kernfs: fix all kernel-doc warnings and multiple typos
driver core: pass a const * into of_device_uevent()
kobject: kset_uevent_ops: make name() callback take a const *
kobject: kset_uevent_ops: make filter() callback take a const *
kobject: make kobject_namespace take a const *
...
Linus Torvalds
Greg Kroah-Hartman
Jakub Kicinski
Kieran Frewen
Jaewan Kim
Aloka Dixit
Felix Fietkau
Hector Martin
Johannes Berg
Jacob Keller
Veerendranath Jakkam
Avraham Stern
Mordechay Goodstein
Marc Bornand
Wen Gong
Lorenzo Bianconi
Vinay Gannevaram
Rameshkumar Sundaram
Alvin Šipraga
Alexander Wetzel
Lukas Wunner
Shivani Baranwal