gcc warns about a potential use of an uninitialized variable in this driver:
drivers/tty/serial/ifx6x60.c: In function 'ifx_spi_complete':
drivers/tty/serial/ifx6x60.c:713:6: warning: 'more' may be used uninitialized in this function [-Wmaybe-uninitialized]
if (more || ifx_dev->spi_more || queue_length > 0 ||
Unlike a lot of other such warnings, this one is correct and describes
an actual problem in the handling of the "IFX_SPI_HEADER_F" result code.
This appears to be a result from a restructuring of the driver that
dates back to before it was merged in the kernel, so it's impossible
to know where it went wrong. I also don't know what that result code
means, so I have no idea if setting 'more' to zero is the correct
solution, but at least it makes the behavior reproducible rather than
depending on whatever happens to be on the kernel stack.
This patch initializes the 'more' variable to zero in each of the
three code paths that could result in undefined behavior before,
which is more explicit than initializing it at the start of the
function.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There's no need to cast the last parameter of {request,free}_irq() to
"void *", as any pointer type is accepted.
Remove the superfluous casts to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Casting spi_driver pointers to "void *" when calling
spi_{,un}register_driver() bypasses all type checking.
Remove the superfluous casts to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ifx6x60 driver implements both legacy suspend/resume callbacks and
dev_pm_ops. The SPI core is going to ignore legacy suspend/resume
callbacks if a driver implements dev_pm_ops. Since the legacy suspend/resume
callbacks are empty in this case it is safe to just remove them.
Cc: Bi Chao <chao.bi@intel.com>
Cc: Chen Jun <jun.d.chen@intel.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It allows for cleaning up on a considerable amount of places. They did
port_get, hangup, kref_put. Now the only thing needed is to call
tty_port_tty_hangup which does exactly that. And they can also decide
whether to consider CLOCAL or completely ignore that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It allows for cleaning up on a considerable amount of places. They did
port_get, wakeup, kref_put. Now the only thing needed is to call
tty_port_tty_wakeup which does exactly that.
One exception is ifx6x60 where tty_wakeup was open-coded. We now call
tty_wakeup properly there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to memset 0 to SPI frame memory before preparing
transfer frame bits, because SPI frame header are encoded with valid
data size, so don't need to worry about adopting dirty bits, more,
memset zero for each SPI frame may impact the spi throughput efficiency.
Signed-off-by: Chen Jun <jun.d.chen@intel.com>
Signed-off-by: channing <chao.bi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.
IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.
Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One point is to have less places where we actually need tty pointer.
The other is that low_latency is bound to buffer processing and
buffers are now in tty_port. So it makes sense to move low_latency to
tty_port too.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_string this time.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As protocol driver, IFX SPI driver initiate to setup SPI master with default
SPI word size as 16 bit/word, however, SPI master may not adopt this default
value due to SPI controller's capability, it might choose an available value by
itself and set it to spi_device.bits_per_word. In order to keep align with
Controller, IFX driver should make use of this value during SPI transfer,
but the default one.
Signed-off-by: Chen Jun <jun.d.chen@intel.com>
Signed-off-by: channing <chao.bi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When shut down SPI port, it's possible that MRDY has been asserted and a SPI
timer was activated waiting for SRDY assert, in the case, it needs to delete
this timer.
Signed-off-by: Chen Jun <jun.d.chen@intel.com>
Signed-off-by: channing <chao.bi@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch add modem power off function in the reboot process according registering
reboot callback to the reboot_notifier_list. Also realizing the spi shutdown function.
Signed-off-by: Bi Chao <chao.bi@intel.com>
Signed-off-by: Chen Jun <jun.d.chen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit "TTY: move tty buffers to tty_port", the tty buffers are
not freed in some drivers. This is because tty_port_destructor is not
called whenever a tty_port is freed. This was an assumption I counted
with but was unfortunately untrue. So fix the drivers to fulfil this
assumption.
To be sure, the TTY buffers (and later some stuff) are gone along with
the tty_port, we have to call tty_port_destroy at tear-down places.
This is mostly where the structure containing a tty_port is freed.
This patch does exactly that -- put tty_port_destroy at those places.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch check whether the fifo lenth is empty before writing new data to fifo.If condition
is true,ifx_spi_write need to trigger one mrdy_assert. If condition is false,the mrdy_assert
will be trigger by the next ifx_spi_io.
Cc: Bi Chao <chao.bi@intel.com>
Signed-off-by: Chen Jun <jun.d.chen@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to correct the bit mapping of "MORE" and "CTS" in SPI frame header.
Per SPI protocol, SPI header is encoded with length of 4 byte, which is defined
as below:
bit 0 ~ 11: current data size;
bit 12: "MORE" bit;
bit 13: reserve
bit 14 ~ 15: reserve
bit 16 ~ 27: next data size
bit 28: RI
bit 29: DCD
bit 30: CTS/RTS
bit 31: DSR/DTR
According to above SPI header structure, the bit mapping of "MORE" and "CTS" is
incorrect in function ifx_spi_decode_spi_header();
Cc: Chen Jun <jun.d.chen@intel.com>
Signed-off-by: channing <chao.bi@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to implement following 2 places to avoid potential error when IFX6x60 port shutdown:
1) Clear Flag IFX_SPI_STATE_IO_AVAILABLE to disable data transfer when Modem port is shutdown;
2) Clear Flag IFX_SPI_STATE_IO_IN_PROGRESS and IFX_SPI_STATE_IO_READY when reopen port.
This is because last port shutdown may happen when SPI/DMA transfer is in progress, if the last
data transfer is not completed(for example due to modem reset), the Flag IFX_SPI_STATE_IO_IN_PROGRESS
will be set forever, so when IFX port is activated again, IFX_SPI_STATE_IO_IN_PROGRESS will prevent
transferring data forever. And if don't clear IFX_SPI_STATE_IO_READY, it may cause one more SPI frame
transferring in spit there is not data need to be transfer.
cc: liu chuansheng <chuansheng.liu@intel.com>
cc: Chen Jun <jun.d.chen@intel.com>
Signed-off-by: channing <chao.bi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch make use of del_timer instead of del_timer_sync in the
interrupt context.
The spi_timer function don't use any resources that may release after
running del_timer,
so using the del_timer is also safe and enough in this context.
Signed-off-by: Chen Jun <jun.d.chen@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Tested-by: Chuansheng Liu <chuansheng.liu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch make use of mod_timer instead of add_timer in the mrdy_assert function.
Because the srdy interrupter can go high when we are running function mrdy_assert and mrdy_assert
can be called by multi-entry. In our medfield platform, spi stress test can encounter this
error logs triggered by the BUG_ON of add_timer function.This patch had been tested on
our medfield platform.
the scenario:
CPU0 CPU1
mrdy_assert
set_bit(IFX_SPI_STATE_TIMER_PENDING)
ifx_spi_handle_srdy
...
clear_bit(IFX_SPI_STATE_TIMER_PENDING)
...
mrdy_assert
set_bit(IFX_SPI_STATE_TIMER_PENDING)
...
add_timer
...
add_timer
Cc: liu chuansheng <chuansheng.liu@intel.com>
Cc: Bi Chao <chao.bi@intel.com>
Signed-off-by: Chen Jun <jun.d.chen@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SPI protocol driver only provide one function (swap_buf()) to swap SPI
data into big endian format, which is only available when SPI
controller's word width is 16 bits. But word width could be configured
as 8/16/32 bits, different word width configure should be mapped to
different swap methods.This patch is to make SPI protocol driver choose
the right swap function corresponding to SPI word width configuration.
cc: liu chuansheng <chuansheng.liu@intel.com>
cc: Chen Jun <jun.d.chen@intel.com>
Signed-off-by: channing <chao.bi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we have no way to assign tty->port while performing tty
installation. There are two ways to provide the link tty_struct =>
tty_port. Either by calling tty_port_install from tty->ops->install or
tty_port_register_device called instead of tty_register_device when
the device is being set up after connected.
In this patch we modify most of the drivers to do the latter. When the
drivers use tty_register_device and we have tty_port already, we
switch to tty_port_register_device. So we have the tty_struct =>
tty_port link for free for those.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All num, magic and owner are set by alloc_tty_driver. No need to
re-set them on each allocation site.
pti driver sets something different to what it passes to
alloc_tty_driver. It is not a bug, since we don't use the lines
parameter in any way. Anyway this is fixed, and now we do the right
thing.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register(),
so we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove linux/mm.h inclusion from netdevice.h -- it's unused (I've checked manually).
To prevent mm.h inclusion via other channels also extract "enum dma_data_direction"
definition into separate header. This tiny piece is what gluing netdevice.h with mm.h
via "netdevice.h => dmaengine.h => dma-mapping.h => scatterlist.h => mm.h".
Removal of mm.h from scatterlist.h was tried and was found not feasible
on most archs, so the link was cutoff earlier.
Hope people are OK with tiny include file.
Note, that mm_types.h is still dragged in, but it is a separate story.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Including linux/tty.h 3 times is a little over the top - once will do.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Doing tiocmget was such fun we should do tiocmset as well for the same
reasons
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't actually need this and it causes problems for internal use of
this functionality. Currently there is a single use of the FILE * pointer.
That is the serial core which uses it to check tty_hung_up_p. However if
that is true then IO_ERROR is also already set so the check may be removed.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
renamed spi_driver variable to not be h/w specific
set driver name to use DRVNAME define
removed commented-out define
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The probe routine should call spi_setup() to configure
the SPI bus so it can properly communicate with the device.
E.g. the device operates in SPI mode 1.
Called spi_setup to configure SPI mode, max_speed_hz, and bpw
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Platforms containing the 6260 can run up to 25Mhz.
For these platforms set max_speed_hz to 25Mhz.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
driver should support 32bit SPI transfers. The boolean variable
only allowed 8/16.
Changed to support 8/16/32 for future enabling
of 32 bpw.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver is a SPI protocol driver and has no DMA ops
associated with the device so the call will fail. Furthermore,
the DMA allocation made here will be used by the SPI
controller driver (parent dev) so it makes sense to
pass that device instead.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The port ops must be set AFTER calling port init as that function
zeroes the structure
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some platform attributes (e.g. max_hz, use_dma) were being intuited
from the modem type. These things should be specified by the platform
data.
Added max_hz, use_dma to ifx_modem_platform_data definition,
replaced is_6160 w/ modem_type, and changed clients accordingly
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The serial drivers are really just tty drivers, so move them to
drivers/tty/ to make things a bit neater overall.
This is part of the tty/serial driver movement proceedure as proposed by
Arnd Bergmann and approved by everyone involved a number of months ago.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Rogier Wolff <R.E.Wolff@bitwizard.nl>
Cc: Michael H. Warfield <mhw@wittsend.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Arnd Bergmann
Andrew F. Davis
Geert Uytterhoeven
Jingoo Han
Lars-Peter Clausen
Jiri Slaby
Greg Kroah-Hartman
channing
Jun Chen
Randy Dunlap
Bill Pemberton
Fengguang Wu
Alexey Dobriyan
Jesper Juhl
Alan Cox
Russ Gorby
Greg Kroah-Hartman