It is hardly (if ever) possible but in case of broken _PXM entry we could
reach out of pxm_to_node_map array bounds in acpi_map_pxm_to_node() call.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
There was a misplaced status test (two consequent tests without a
statement in between) in acpi_bus_init for ages. Remove it, since the
function which should be checked (acpi_os_initialize1) has BUG_ONs on
failure paths.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This reverts commit 5ec5d38a1c.
because it caused spurious dmesg warmings.
We'll implement the check for off-limit ports
in a more clever way in the future.
http://bugzilla.kernel.org/show_bug.cgi?id=12758
Signed-off-by: Len Brown <len.brown@intel.com>
Switch the Asus Pundit P1-AH2 (M2N8L motherboard) to the old ACPI 1.0
sleep ordering by default. Without this it will not suspend/resume
correctly.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Tested-by: Dustin Kirkland <kirkland@canonical.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove CONFIG_ACPI_SYSTEM. It was always set the same as CONFIG_ACPI,
and it had no menu label, so there was no way to set it to anything
other than "y".
Some things under CONFIG_ACPI_SYSTEM (acpi_irq_handled, acpi_os_gpe_count(),
event_is_open, register_acpi_notifier(), etc.) are used unconditionally
by the CA, the OSPM, and drivers, so we depend on them always being
present.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
On hardware like the T61 it can take a couple of seconds for the battery
to start charging after the power is connected, and we incorrectly tell
userspace that we are fully charged, and then go back to charging.
Only mark a battery as fully charged when the preset charge matches either
the last full charge, or the design charge.
http://bugzilla.kernel.org/show_bug.cgi?id=12632
Signed-off-by: Richard Hughes <hughsient@gmail.com>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
During early boot, ACPI RSDT/XSDT table entries are gathered into the
'initial_tables[]' array. This array is currently statically defined (see
./drivers/acpi/tables.c). When there are more table entries than can be
held in the 'initial_tables[]' array, the message "Truncating N table
entries!" is output. As currently implemented, this message will always
erroneously calculate N as 0.
This patch fixes the calculation that determines how many table entries
will be missing (truncated).
This modification may be used under either the GPL or the BSD-style
license used for Intel ACPI CA code.
Signed-off-by: Myron Stowe <myron.stowe@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
According to kerneljanitors todo list all printk calls (beginning
a new line) should have an according KERN_* constant.
Those are the missing peaces here for the acpi subsystem.
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Some devices trigger a DEVICE_CHECK on every evalutation of _STA. This
can also be seen in commit 8b59560a3b
(ACPI: dock: avoid check _STA method). If an undock is processed, the
dock driver sends a uevent and userspace might read the show_docked
property in sysfs. This causes an evaluation of _STA of the particular
device which causes the dock driver to immediately dock again.
In any case, evaluation of _STA (show_docked) does not necessarily mean
that we are docked, so check with the internal device structure.
http://bugzilla.kernel.org/show_bug.cgi?id=12360
Signed-off-by: Holger Macht <hmacht@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
When ACPI is disabled in the BIOS of this VIA C3 box,
it invalidates the RSDP, which Linux notices:
ACPI Error (tbxfroot-0218): A valid RSDP was not found [20080926]
Bug Linux neglected to disable ACPI at that stage,
and later scribbled on smp_found_config:
ACPI: No APIC-table, disabling MPS
But this box doesn't run well in legacy PIC mode,
it needed IOAPIC mode to perform correctly:
http://lkml.org/lkml/2009/2/5/39
So exit ACPI mode cleanly when we first detect
that it is hopeless.
Signed-off-by: Len Brown <len.brown@intel.com>
CPU_IDLE=y has been default for ACPI=y since Nov-2007,
and has shipped in many distributions since then.
Here we delete the CPU_IDLE=n ACPI idle code, since
nobody should be using it, and we don't want to
maintain two versions.
Signed-off-by: Len Brown <len.brown@intel.com>
They were long enough set deprecated...
Update Documentation/cpu-freq/users-guide.txt:
The deprecated files listed there seen not to exist for some time anymore
already.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPICA exports acpi_os_validate_address() so the OS
can prevent BIOS AML from accessing specified addresses.
Start using this interface to prevent AML from accessing
some well known IO addresses that the OS "owns".
Signed-off-by: Len Brown <len.brown@intel.com>
on boot, print out the OSI strings the BIOS uses to query the OS.
To see this output...
build with CONFIG_ACPI_DEBUG
boot with
"acpi.debug_level=4" (ACPI_LV_INFO) (enabled by default)
and
"acpi.debug_level=1" (ACPI_UTILITIES) (default is 0)
example output:
ACPI: BIOS _OSI(Windows 2001) supported
ACPI: BIOS _OSI(Windows 2001 SP1) supported
ACPI: BIOS _OSI(Windows 2001 SP2) supported
ACPI: BIOS _OSI(Windows 2006) supported
ACPI: BIOS _OSI(Linux) not-supported
ACPI: BIOS _OSI(FreeBSD) not-supported
Signed-off-by: Len Brown <len.brown@intel.com>
According to the Spec the first two elements in the _BCL package won't be
regarded as the available brightness level. The first is the brightness when
full power is connected to the box(It means that the AC adapter is plugged).
The second is the brightness level when the box is on battery.
If the first two elements are still used while finding the next brightness
level, it will fall back to the lowest level when keeping on pressing
hotkey. (On some boxes the brightness will be changed twice when hotkey is
pressed once. One is in the ACPI video driver. The other is changed by sys I/F.
In the ACPI video driver the first two elements will be used while changing
the brightness. But the first two elements is skipped while using sys I/F.
In such case there exists the inconsistency).
So he first two elements had better be skipped while showing the available
brightness or finding the next brightness level.
http://bugzilla.kernel.org/show_bug.cgi?id=12450
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
It is true that BM_RLD needs to be set to enable
bus master activity to wake an older chipset (eg PIIX4) from C3.
This is contrary to the erroneous wording the ACPI 2.0, 3.0
specifications that suggests that BM_RLD is an indicator
rather than a control bit.
ACPI 1.0's correct wording should be restored in ACPI 4.0:
http://www.acpica.org/bugzilla/show_bug.cgi?id=689
But the kernel should not have to clear BM_RLD
when entering a non C3-type state just to set
it again when entering a C3-type C-state.
We should be able to set BM_RLD at boot time
and leave it alone -- removing the overhead of
accessing this IO register from the idle entry path.
Signed-off-by: Len Brown <len.brown@intel.com>
PM1a_STS and PM1b_STS are twins that get OR'd together
on reads, and all writes are repeated to both.
The fields in PM1x_STS are single bits only,
there are no multi-bit fields.
So it is not necessary to lock PM1x_STS reads against
writes because it is impossible to read an intermediate
value of a single bit. It will either be 0 or 1,
even if a write is in progress during the read.
Reads are asynchronous to writes no matter if a lock
is used or not.
Signed-off-by: Len Brown <len.brown@intel.com>
This patch fixes the crash I experienced in 2.6.29-rc2.
Tested on ASUS M50vm.
Signed-off-by: Tero Roponen <tero.roponen@gmail.com>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix two compilation warnings in drivers/acpi/sleep.c, one triggered
by unsetting CONFIG_SUSPEND and the other triggered by unsetting
CONFIG_HIBERNATION, by moving some code under the appropriate
#ifdefs .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Conflicts:
drivers/acpi/pci_irq.c
Note that this merge disables
e1d3a90846
pci, acpi: reroute PCI interrupt to legacy boot interrupt equivalent
Signed-off-by: Len Brown <len.brown@intel.com>
when CONFIG_RTC_DRV_CMOS=m
and thus !defined(HAVE_ACPI_LEGACY_ALARM)
drivers/acpi/proc.c:85: warning: ‘cmos_bcd_read’ declared ‘static’ but
never defined
Signed-off-by: Len Brown <len.brown@intel.com>
On some boxes there exist both RSDT and XSDT table. But unfortunately
sometimes there exists the following error when XSDT table is used:
a. 32/64X address mismatch
b. The 32/64X FACS address mismatch
In such case the boot option of "acpi=rsdt" is provided so that
RSDT is tried instead of XSDT table when the system can't work well.
http://bugzilla.kernel.org/show_bug.cgi?id=8246
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
cc:Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI_USE_LOCAL_CACHE will never be defined by the Linux kernel,
and thus utcache.c will always be dead code.
Signed-off-by: Len Brown <len.brown@intel.com>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (98 commits)
PCI PM: Put PM callbacks in the order of execution
PCI PM: Run default PM callbacks for all devices using new framework
PCI PM: Register power state of devices during initialization
PCI PM: Call pci_fixup_device from legacy routines
PCI PM: Rearrange code in pci-driver.c
PCI PM: Avoid touching devices behind bridges in unknown state
PCI PM: Move pci_has_legacy_pm_support
PCI PM: Power-manage devices without drivers during suspend-resume
PCI PM: Add suspend counterpart of pci_reenable_device
PCI PM: Fix poweroff and restore callbacks
PCI: Use msleep instead of cpu_relax during ASPM link retraining
PCI: PCIe portdrv: Add kerneldoc comments to remining core funtions
PCI: PCIe portdrv: Rearrange code so that related things are together
PCI: PCIe portdrv: Fix suspend and resume of PCI Express port services
PCI: PCIe portdrv: Add kerneldoc comments to some core functions
x86/PCI: Do not use interrupt links for devices using MSI-X
net: sfc: Use pci_clear_master() to disable bus mastering
PCI: Add pci_clear_master() as opposite of pci_set_master()
PCI hotplug: remove redundant test in cpq hotplug
PCI: pciehp: cleanup register and field definitions
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
The _OSC capability OSC_MSI_SUPPORT is set when the root bridge is added
with pci_acpi_osc_support(), so we no longer need to do it in the PCI
MSI driver. Also adds the function pci_msi_enabled, which returns true
if pci=nomsi is not on the kernel command-line.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cyrill Gorcunov
Jiri Slaby
Zhang Rui
Len Brown
Andy Whitcroft
Bjorn Helgaas
Richard Hughes
Alexey Starikovskiy
Thierry Vignaud
Myron Stowe
Kay Sievers
Frank Seidel
Holger Macht
Thomas Renninger
Zhao Yakui
Tero Roponen
Rafael J. Wysocki
Linus Torvalds
Andrew Patterson