This commit:
5fdf8e5ba5 ("libnvdimm: re-enable deep flush for pmem devices via fsync()")
intended to make sure that deep flush was always available even on
platforms which support a power-fail protected CPU cache. An unintended
side effect of this change was that we also lost the ability to skip
flushing CPU caches on those power-fail protected CPU cache.
Fix this by skipping the low level cache flushing in dax_flush() if we have
CPU caches which are power-fail protected. The user can still override this
behavior by manually setting the write_cache state of a namespace. See
libndctl's ndctl_namespace_write_cache_is_enabled(),
ndctl_namespace_enable_write_cache() and
ndctl_namespace_disable_write_cache() functions.
Cc: <stable@vger.kernel.org>
Fixes: 5fdf8e5ba5 ("libnvdimm: re-enable deep flush for pmem devices via fsync()")
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Prior to this commit we would only do a "deep flush" (have nvdimm_flush()
write to each of the flush hints for a region) in response to an
msync/fsync/sync call if the nvdimm_has_cache() returned true at the time
we were setting up the request queue. This happens due to the write cache
value passed in to blk_queue_write_cache(), which then causes the block
layer to send down BIOs with REQ_FUA and REQ_PREFLUSH set. We do have a
"write_cache" sysfs entry for namespaces, i.e.:
/sys/bus/nd/devices/pfn0.1/block/pmem0/dax/write_cache
which can be used to control whether or not the kernel thinks a given
namespace has a write cache, but this didn't modify the deep flush behavior
that we set up when the driver was initialized. Instead, it only modified
whether or not DAX would flush CPU caches via dax_flush() in response to
*sync calls.
Simplify this by making the *sync deep flush always happen, regardless of
the write cache setting of a namespace. The DAX CPU cache flushing will
still be controlled the write_cache setting of the namespace.
Cc: <stable@vger.kernel.org>
Fixes: 5fdf8e5ba5 ("libnvdimm: re-enable deep flush for pmem devices via fsync()")
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Complete the move from REQ_FLUSH to REQ_PREFLUSH that apparently started
way back in v4.8.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There is currently a mismatch between the resources that will trigger
the e820_pmem driver to register/load and the resources that will
actually be surfaced as pmem ranges. register_e820_pmem() uses
walk_iomem_res_desc() which includes children and siblings. In contrast,
e820_pmem_probe() only considers top level resources. For example the
following resource tree results in the driver being loaded, but no
resources being registered:
398000000000-39bfffffffff : PCI Bus 0000:ae
39be00000000-39bf07ffffff : PCI Bus 0000:af
39be00000000-39beffffffff : 0000:af:00.0
39be10000000-39beffffffff : Persistent Memory (legacy)
Fix this up to allow definitions of "legacy" pmem ranges anywhere in
system-physical address space. Not that it is a recommended or safe to
define a pmem range in PCI space, but it is useful for debug /
experimentation, and the restriction on being a top-level resource was
arbitrary.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Instrument nvdimm_bus_probe() to emit timestamps for the start and end
of libnvdimm device probing. This is useful for identifying sources of
libnvdimm sub-system initialization latency.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The pmem driver does not honor a forced read-only setting for very long:
$ blockdev --setro /dev/pmem0
$ blockdev --getro /dev/pmem0
1
followed by various commands like these:
$ blockdev --rereadpt /dev/pmem0
or
$ mkfs.ext4 /dev/pmem0
results in this in the kernel serial log:
nd_pmem namespace0.0: region0 read-write, marking pmem0 read-write
with the read-only setting lost:
$ blockdev --getro /dev/pmem0
0
That's from bus.c nvdimm_revalidate_disk(), which always applies the
setting from nd_region (which is initially based on the ACPI NFIT
NVDIMM state flags not_armed bit).
In contrast, commit 20bd1d026a ("scsi: sd: Keep disk read-only when
re-reading partition") fixed this issue for SCSI devices to preserve
the previous setting if it was set to read-only.
This patch modifies bus.c to preserve any previous read-only setting.
It also eliminates the kernel serial log print except for cases where
read-write is changed to read-only, so it doesn't print read-only to
read-only non-changes.
Cc: <stable@vger.kernel.org>
Fixes: 5813882094 ("libnvdimm, nfit: handle unarmed dimms, mark namespaces read-only")
Signed-off-by: Robert Elliott <elliott@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use the machine check safe version of copy_to_iter() for the
->copy_to_iter() operation published by the pmem driver.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Similar to the ->copy_from_iter() operation, a platform may want to
deploy an architecture or device specific routine for handling reads
from a dax_device like /dev/pmemX. On x86 this routine will point to a
machine check safe version of copy_to_iter(). For now, add the plumbing
to device-mapper and the dax core.
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for fixing dax-dma-vs-unmap issues, filesystems need to
be able to rely on the fact that they will get wakeups on dev_pagemap
page-idle events. Introduce MEMORY_DEVICE_FS_DAX and
generic_dax_page_free() as common indicator / infrastructure for dax
filesytems to require. With this change there are no users of the
MEMORY_DEVICE_HOST designation, so remove it.
The HMM sub-system extended dev_pagemap to arrange a callback when a
dev_pagemap managed page is freed. Since a dev_pagemap page is free /
idle when its reference count is 1 it requires an additional branch to
check the page-type at put_page() time. Given put_page() is a hot-path
we do not want to incur that check if HMM is not in use, so a static
branch is used to avoid that overhead when not necessary.
Now, the FS_DAX implementation wants to reuse this mechanism for
receiving dev_pagemap ->page_free() callbacks. Rework the HMM-specific
static-key into a generic mechanism that either HMM or FS_DAX code paths
can enable.
For ARCH=um builds, and any other arch that lacks ZONE_DEVICE support,
care must be taken to compile out the DEV_PAGEMAP_OPS infrastructure.
However, we still need to support FS_DAX in the FS_DAX_LIMITED case
implemented by the s390/dcssblk driver.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Michal Hocko <mhocko@suse.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Thomas Meyer <thomas@m3y3r.de>
Reported-by: Dave Jiang <dave.jiang@intel.com>
Cc: "Jérôme Glisse" <jglisse@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Machine check safe memory copies are currently deployed in the pmem
driver whenever reading from persistent memory media, so that -EIO is
returned rather than triggering a kernel panic. While this protects most
pmem accesses, it is not complete in the filesystem-dax case. When
filesystem-dax is enabled reads may bypass the block layer and the
driver via dax_iomap_actor() and its usage of copy_to_iter().
In preparation for creating a copy_to_iter() variant that can handle
machine checks, teach memcpy_mcsafe() to return the number of bytes
remaining rather than -EFAULT when an exception occurs.
Co-developed-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: hch@lst.de
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-nvdimm@lists.01.org
Link: http://lkml.kernel.org/r/152539238119.31796.14318473522414462886.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
With commit df3f126482 ("libnvdimm, of_pmem: use dev_to_node() instead
of of_node_to_nid()") it is now possible to allow of_pmem to be built as
a module as originally implemented.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Remove the direct dependency on of_node_to_nid() by using dev_to_node()
instead. Any DT platform device will have its NUMA node id set when the
device is created.
With this, commit 291717b6fb ("libnvdimm, of_pmem: workaround OF_NUMA=n
build error") can be reverted.
Fixes: 7171976089 ("libnvdimm: Add device-tree based driver")
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Oliver O'Halloran <oohall@gmail.com>
Cc: linux-nvdimm@lists.01.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The new support for the standard _LSR and _LSW methods neglected to also
update the nvdimm_init_config_data() and nvdimm_set_config_data() to
return the translated error code from failed commands. This precision is
necessary because the locked status that was previously returned on
ND_CMD_GET_CONFIG_SIZE commands is now returned on
ND_CMD_{GET,SET}_CONFIG_DATA commands.
If the kernel misses this indication it can inadvertently fall back to
label-less mode when it should otherwise avoid all access to locked
regions.
Cc: <stable@vger.kernel.org>
Fixes: 4b27db7e26 ("acpi, nfit: add support for the _LSI, _LSR, and...")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* A rework of the filesytem-dax implementation provides for detection of
unmap operations (truncate / hole punch) colliding with in-progress
device-DMA. A fix for these collisions remains a work-in-progress
pending resolution of truncate latency and starvation regressions.
* The of_pmem driver expands the users of libnvdimm outside of x86 and
ACPI to describe an implementation of persistent memory on PowerPC with
Open Firmware / Device tree.
* Address Range Scrub (ARS) handling is completely rewritten to account for
the fact that ARS may run for 100s of seconds and there is no platform
defined way to cancel it. ARS will now no longer block namespace
initialization.
* The NVDIMM Namespace Label implementation is updated to handle label
areas as small as 1K, down from 128K.
* Miscellaneous cleanups and updates to unit test infrastructure.
-----BEGIN PGP SIGNATURE-----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=acZQ
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"This cycle was was not something I ever want to repeat as there were
several late changes that have only now just settled.
Half of the branch up to commit d2c997c0f1 ("fs, dax: use
page->mapping to warn...") have been in -next for several releases.
The of_pmem driver and the address range scrub rework were late
arrivals, and the dax work was scaled back at the last moment.
The of_pmem driver missed a previous merge window due to an oversight.
A sense of obligation to rectify that miss is why it is included for
4.17. It has acks from PowerPC folks. Stephen reported a build failure
that only occurs when merging it with your latest tree, for now I have
fixed that up by disabling modular builds of of_pmem. A test merge
with your tree has received a build success report from the 0day robot
over 156 configs.
An initial version of the ARS rework was submitted before the merge
window. It is self contained to libnvdimm, a net code reduction, and
passing all unit tests.
The filesystem-dax changes are based on the wait_var_event()
functionality from tip/sched/core. However, late review feedback
showed that those changes regressed truncate performance to a large
degree. The branch was rewound to drop the truncate behavior change
and now only includes preparation patches and cleanups (with full acks
and reviews). The finalization of this dax-dma-vs-trnucate work will
need to wait for 4.18.
Summary:
- A rework of the filesytem-dax implementation provides for detection
of unmap operations (truncate / hole punch) colliding with
in-progress device-DMA. A fix for these collisions remains a
work-in-progress pending resolution of truncate latency and
starvation regressions.
- The of_pmem driver expands the users of libnvdimm outside of x86
and ACPI to describe an implementation of persistent memory on
PowerPC with Open Firmware / Device tree.
- Address Range Scrub (ARS) handling is completely rewritten to
account for the fact that ARS may run for 100s of seconds and there
is no platform defined way to cancel it. ARS will now no longer
block namespace initialization.
- The NVDIMM Namespace Label implementation is updated to handle
label areas as small as 1K, down from 128K.
- Miscellaneous cleanups and updates to unit test infrastructure"
* tag 'libnvdimm-for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (39 commits)
libnvdimm, of_pmem: workaround OF_NUMA=n build error
nfit, address-range-scrub: add module option to skip initial ars
nfit, address-range-scrub: rework and simplify ARS state machine
nfit, address-range-scrub: determine one platform max_ars value
powerpc/powernv: Create platform devs for nvdimm buses
doc/devicetree: Persistent memory region bindings
libnvdimm: Add device-tree based driver
libnvdimm: Add of_node to region and bus descriptors
libnvdimm, region: quiet region probe
libnvdimm, namespace: use a safe lookup for dimm device name
libnvdimm, dimm: fix dpa reservation vs uninitialized label area
libnvdimm, testing: update the default smart ctrl_temperature
libnvdimm, testing: Add emulation for smart injection commands
nfit, address-range-scrub: introduce nfit_spa->ars_state
libnvdimm: add an api to cast a 'struct nd_region' to its 'struct device'
nfit, address-range-scrub: fix scrub in-progress reporting
dax, dm: allow device-mapper to operate without dax support
dax: introduce CONFIG_DAX_DRIVER
fs, dax: use page->mapping to warn if truncate collides with a busy page
ext2, dax: introduce ext2_dax_aops
...
Stephen reports that an x86 allmodconfig build fails to build the
of_pmem driver due to a missing definition of of_node_to_nid(). That
helper is currently only exported in the OF_NUMA=y case. In other cases,
ppc and sparc, it is a weak symbol, and outside of those platforms it is
a static inline.
Until an OF_NUMA=n configuration can reliably support usage of
of_node_to_nid() in modules across architectures, mark this driver as
'bool' instead of 'tristate'.
Cc: Rob Herring <robh@kernel.org>
Cc: Oliver O'Halloran <oohall@gmail.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds peliminary device-tree bindings for persistent memory
regions. The driver registers a libnvdimm bus for each pmem-region
node and each address range under the node is converted to a region
within that bus.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We want to be able to cross reference the region and bus devices
with the device tree node that they were spawned from. libNVDIMM
handles creating the actual devices for these internally, so we
need to pass in a pointer to the relevant node in the descriptor.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The message about constraining number of online cpus to be less than or
equal to ND_MAX_LANES (256) is only useful for block-aperture
configurations and BTT. Make it debug since it is only relevant when
debugging performance.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The following NULL dereference results from incorrectly assuming that
ndd is valid in this print:
struct nvdimm_drvdata *ndd = to_ndd(&nd_region->mapping[i]);
/*
* Give up if we don't find an instance of a uuid at each
* position (from 0 to nd_region->ndr_mappings - 1), or if we
* find a dimm with two instances of the same uuid.
*/
dev_err(&nd_region->dev, "%s missing label for %pUb\n",
dev_name(ndd->dev), nd_label->uuid);
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
IP: nd_region_register_namespaces+0xd67/0x13c0 [libnvdimm]
PGD 0 P4D 0
Oops: 0000 [#1] SMP PTI
CPU: 43 PID: 673 Comm: kworker/u609:10 Not tainted 4.16.0-rc4+ #1
[..]
RIP: 0010:nd_region_register_namespaces+0xd67/0x13c0 [libnvdimm]
[..]
Call Trace:
? devres_add+0x2f/0x40
? devm_kmalloc+0x52/0x60
? nd_region_activate+0x9c/0x320 [libnvdimm]
nd_region_probe+0x94/0x260 [libnvdimm]
? kernfs_add_one+0xe4/0x130
nvdimm_bus_probe+0x63/0x100 [libnvdimm]
Switch to using the nvdimm device directly.
Fixes: 0e3b0d123c ("libnvdimm, namespace: allow multiple pmem...")
Cc: <stable@vger.kernel.org>
Reported-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
At initialization time the 'dimm' driver caches a copy of the memory
device's label area and reserves address space for each of the
namespaces defined.
However, as can be seen below, the reservation occurs even when the
index blocks are invalid:
nvdimm nmem0: nvdimm_init_config_data: len: 131072 rc: 0
nvdimm nmem0: config data size: 131072
nvdimm nmem0: __nd_label_validate: nsindex0 labelsize 1 invalid
nvdimm nmem0: __nd_label_validate: nsindex1 labelsize 1 invalid
nvdimm nmem0: : pmem-6025e505: 0x1000000000 @ 0xf50000000 reserve <-- bad
Gate dpa reservation on the presence of valid index blocks.
Cc: <stable@vger.kernel.org>
Fixes: 4a826c83db ("libnvdimm: namespace indices: read and validate")
Reported-by: Krzysztof Rusocki <krzysztof.rusocki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RVhK
-----END PGP SIGNATURE-----
Merge tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"It's a pretty quiet round this time, which is nice. This contains:
- series from Bart, cleaning up the way we set/test/clear atomic
queue flags.
- series from Bart, fixing races between gendisk and queue
registration and removal.
- set of bcache fixes and improvements from various folks, by way of
Michael Lyle.
- set of lightnvm updates from Matias, most of it being the 1.2 to
2.0 transition.
- removal of unused DIO flags from Nikolay.
- blk-mq/sbitmap memory ordering fixes from Omar.
- divide-by-zero fix for BFQ from Paolo.
- minor documentation patches from Randy.
- timeout fix from Tejun.
- Alpha "can't write a char atomically" fix from Mikulas.
- set of NVMe fixes by way of Keith.
- bsg and bsg-lib improvements from Christoph.
- a few sed-opal fixes from Jonas.
- cdrom check-disk-change deadlock fix from Maurizio.
- various little fixes, comment fixes, etc from various folks"
* tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block: (139 commits)
blk-mq: Directly schedule q->timeout_work when aborting a request
blktrace: fix comment in blktrace_api.h
lightnvm: remove function name in strings
lightnvm: pblk: remove some unnecessary NULL checks
lightnvm: pblk: don't recover unwritten lines
lightnvm: pblk: implement 2.0 support
lightnvm: pblk: implement get log report chunk
lightnvm: pblk: rename ppaf* to addrf*
lightnvm: pblk: check for supported version
lightnvm: implement get log report chunk helpers
lightnvm: make address conversions depend on generic device
lightnvm: add support for 2.0 address format
lightnvm: normalize geometry nomenclature
lightnvm: complete geo structure with maxoc*
lightnvm: add shorten OCSSD version in geo
lightnvm: add minor version to generic geometry
lightnvm: simplify geometry structure
lightnvm: pblk: refactor init/exit sequences
lightnvm: Avoid validation of default op value
lightnvm: centralize permission check for lightnvm ioctl
...
For debug, it is useful for bus providers to be able to retrieve the
'struct device' associated with an nd_region instance that it
registered. We already have to_nd_region() to perform the reverse cast
operation, in fact its duplicate declaration can be removed from the
private drivers/nvdimm/nd.h header.
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In support of allowing device-mapper to compile out idle/dead code when
there are no dax providers in the system, introduce the DAX_DRIVER
symbol. This is selected by all leaf drivers that device-mapper might be
layered on top. This allows device-mapper to conditionally 'select DAX'
only when a provider is present.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Reported-by: Bart Van Assche <Bart.VanAssche@wdc.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The persistence domain is a point in the platform where once writes
reach that destination the platform claims it will make them persistent
relative to power loss. In the ACPI NFIT this is currently communicated
as 2 bits in the "NFIT - Platform Capabilities Structure". The bits
comprise a hierarchy, i.e. bit0 "CPU Cache Flush to NVDIMM Durability on
Power Loss Capable" implies bit1 "Memory Controller Flush to NVDIMM
Durability on Power Loss Capable".
Commit 96c3a23905 "libnvdimm: expose platform persistence attr..."
shows the persistence domain as flags, but it's really an enumerated
hierarchy.
Fix this newly introduced user ABI to show the closest available
persistence domain before userspace develops dependencies on seeing, or
needing to develop code to tolerate, the raw NFIT flags communicated
through the libnvdimm-generic region attribute.
Fixes: 96c3a23905 ("libnvdimm: expose platform persistence attr...")
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Similar to other region attributes, do not emit the persistence_domain
attribute if its contents are empty.
Fixes: 96c3a23905 ("libnvdimm: expose platform persistence attr...")
Cc: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
It happens often while I'm preparing a patch for a block driver that
I'm wondering: is a definition of SECTOR_SIZE and/or SECTOR_SHIFT
available for this driver? Do I have to introduce definitions of these
constants before I can use these constants? To avoid this confusion,
move the existing definitions of SECTOR_SIZE and SECTOR_SHIFT into the
<linux/blkdev.h> header file such that these become available for all
block drivers. Make the SECTOR_SIZE definition in the uapi msdos_fs.h
header file conditional to avoid that including that header file after
<linux/blkdev.h> causes the compiler to complain about a SECTOR_SIZE
redefinition.
Note: the SECTOR_SIZE / SECTOR_SHIFT / SECTOR_BITS definitions have
not been removed from uapi header files nor from NAND drivers in
which these constants are used for another purpose than converting
block layer offsets and sizes into a number of sectors.
Cc: David S. Miller <davem@davemloft.net>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
sizeof_namespace_index() fails when NVDIMM devices have the minimum
1024 bytes label storage area. nvdimm_num_label_slots() returns 3
slots while the area is only big enough for 2 slots.
Change nvdimm_num_label_slots() to calculate a number of label slots
according to UEFI 2.7 spec.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
UEFI 2.7 defines in page 758 that:
Initial Label Storage Area Configuration
:
The minimum size of the Label Storage Area is large enough to
hold 2 index blocks and 2 labels.
The mininum index block size is 256 bytes, and the minimum label size
is also 256 bytes.
Change ND_LABEL_MIN_SIZE to (256 * 4) so that NVDIMM devices with
the minimum label storage area do not fail with the size check in
nvdimm_init_config_data().
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use module_nd_driver() instead of having module_init() and
module_exit() callbacks which just call nd_driver_register() and
nd_driver_unregister().
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Pointer dev is being assigned a value that is never read, it is being
re-assigned the same value later on, hence the initialization is redundant
and can be removed.
Cleans up clang warning:
drivers/nvdimm/pfn_devs.c:307:17: warning: Value stored to 'dev' during
its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch has been generated as follows:
for verb in set_unlocked clear_unlocked set clear; do
replace-in-files queue_flag_${verb} blk_queue_flag_${verb%_unlocked} \
$(git grep -lw queue_flag_${verb} drivers block/bsg*)
done
Except for protecting all queue flag changes with the queue lock
this patch does not change any functionality.
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Prior to 25520d55cd ("block: Inline blk_integrity in struct gendisk")
we needed to temporarily add a zero-capacity disk before registering for
blk-integrity. But adding a zero-capacity disk caused the partition
table scanning to bail early, and this resulted in partitions not coming
up after a probe of the BTT or blk namespaces.
We can now register for integrity before the disk has been added, and
this fixes the rescan problems.
Fixes: 25520d55cd ("block: Inline blk_integrity in struct gendisk")
Reported-by: Dariusz Dokupil <dariusz.dokupil@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dynamic debug can be instructed to add the function name to the debug
output using the +f switch, so there is no need for the libnvdimm
modules to do it again. If a user decides to add the +f switch for
libnvdimm's dynamic debug this results in double prints of the function
name.
Reported-by: Johannes Thumshirn <jthumshirn@suse.de>
Reported-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Re-enable deep flush so that users always have a way to be sure that a
write makes it all the way out to media. Writes from the PMEM driver
always arrive at the NVDIMM since movnt is used to bypass the cache, and
the driver relies on the ADR (Asynchronous DRAM Refresh) mechanism to
flush write buffers on power failure. The Deep Flush mechanism is there
to explicitly write buffers to protect against (rare) ADR failure. This
change prevents a regression in deep flush behavior so that applications
can continue to depend on fsync() as a mechanism to trigger deep flush
in the filesystem-DAX case.
Fixes: 06e8ccdab1 ("acpi: nfit: Add support for detect platform CPU cache...")
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pointer nd_mapping is being initialized to a value that is never read,
instead it is being updated to a new value in all the cases where it
is being read afterwards, hence the initialization is redundant and
can be removed.
Cleans up clang warning:
drivers/nvdimm/namespace_devs.c:2411:21: warning: Value stored to
'nd_mapping' during its initialization is never rea
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Providing a sysfs attribute for nd_region that shows the persistence
capabilities for the platform.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
In ACPI 6.2a the platform capability structure has been added to the NFIT
tables. That provides software the ability to determine whether a system
supports the auto flushing of CPU caches on power loss. If the capability
is supported, we do not need to do dax_flush(). Plumbing the path to set the
property on per region from the NFIT tables.
This patch depends on the ACPI NFIT 6.2a platform capabilities support code
in include/acpi/actbl1.h.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
When a sector mode namespace is initially created, the arena's err_lock
is not initialized. If, on the other hand, the namespace already
exists, the mutex is initialized. To fix the issue, I moved the mutex
initialization into the arena_alloc, which is called by both
discover_arenas and create_arenas.
This was discovered on an older kernel where mutex_trylock checks the
count to determine whether the lock is held. Because the data structure
is kzalloc-d, that count was 0 (held), and I/O to the device would hang
forever waiting for the lock to be released (see btt_write_pg, for
example). Current kernels have a different mutex implementation that
checks for a non-null owner, and so this doesn't show up as a problem.
If that lock were ever contended, it might cause issues, but you'd have
to be really unlucky, I think.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This new interface is similar to how struct device (and many others)
work. The caller initializes a 'struct dev_pagemap' as required
and calls 'devm_memremap_pages'. This allows the pagemap structure to
be embedded in another structure and thus container_of can be used. In
this way application specific members can be stored in a containing
struct.
This will be used by the P2P infrastructure and HMM could probably
be cleaned up to use it as well (instead of having it's own, similar
'hmm_devmem_pages_create' function).
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Due to a spec misinterpretation, the Linux implementation of the BTT log
area had different padding scheme from other implementations, such as
UEFI and NVML.
This fixes the padding scheme, and defaults to it for new BTT layouts.
We attempt to detect the padding scheme in use when probing for an
existing BTT. If we detect the older/incompatible scheme, we continue
using it.
Reported-by: Juston Li <juston.li@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: <stable@vger.kernel.org>
Fixes: 5212e11fde ("nd_btt: atomic sector updates")
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Recent updates to btt.h neglected to add corresponding kernel-doc lines
for new structure members. Add them.
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The following namespace configuration attempt:
# ndctl create-namespace -e namespace0.0 -m devdax -a 1G -f
libndctl: ndctl_dax_enable: dax0.1: failed to enable
Error: namespace0.0: failed to enable
failed to reconfigure namespace: No such device or address
...fails when the backing memory range is not physically aligned to 1G:
# cat /proc/iomem | grep Persistent
210000000-30fffffff : Persistent Memory (legacy)
In the above example the 4G persistent memory range starts and ends on a
256MB boundary.
We handle this case correctly when needing to handle cases that violate
section alignment (128MB) collisions against "System RAM", and we simply
need to extend that padding/truncation for the 1GB alignment use case.
Cc: <stable@vger.kernel.org>
Fixes: 315c562536 ("libnvdimm, pfn: add 'align' attribute...")
Reported-and-tested-by: Jane Chu <jane.chu@oracle.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The alignment checks at pfn driver startup fail to properly account for
the 'start_pad' in the case where the namespace is misaligned relative
to its internal alignment. This is typically triggered in 1G aligned
namespace, but could theoretically trigger with small namespace
alignments. When this triggers the kernel reports messages of the form:
dax2.1: bad offset: 0x3c000000 dax disabled align: 0x40000000
Cc: <stable@vger.kernel.org>
Fixes: 1ee6667cd8 ("libnvdimm, pfn, dax: fix initialization vs autodetect...")
Reported-by: Jane Chu <jane.chu@oracle.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams
Ross Zwisler
Robert Elliott
Rob Herring
Linus Torvalds
Oliver O'Halloran
Bart Van Assche
Toshi Kani
Johannes Thumshirn
Colin Ian King
Vishal Verma
Dave Jiang
Jeff Moyer
Christoph Hellwig