Currently the udc pullup is enabled by default on boot. If the device
is connected to a host at this time, the host starts the negotiation
before the udc/gadget driver is ready to handle it.
Signed-off-by: Christian Glindkamp <christian.glindkamp@taskit.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add NEW_LEDs support for the following boards:
- Cogent CSB337
- Atmel AT91RM9200-DK
- Atmel AT91RM9200-EK
- Atmel AT91SAM9263-EK
Mostly based on patch from David Brownell.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Due to errata regarding the handling of SPI CS0 on the AT91RM9200, the
atmel_spi driver drives CS0 from the SPI controller and not as a GPIO
pin.
We therefore need to configure CS0 for use by the controller
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for the 3 GPIO-connected buttons on the CSB300 board.
Based on wakeup testing code from David Brownell.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the LED initialization code out of the various *_devices.c files,
and into leds.c.
Also add support for NEW_LEDs.
Patch from David Brownell.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Modify the UART initialization to allow the board-initialization code
to specify which pins are connected, and which pins should therefore
be initialized.
The current at91_init_serial() will continue to work as-is, but is
marked as "deprecated" and will be removed once the board-specific
files has been updated to use the new interface.
As in the AVR32 code, we assume that the TX and RX pins will always be
initialized.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Map the complete memory region (SZ_256M) as is done on the other AT91
processors.
The SMC_SMARTMEDIA bit should be set in the EBI controller to enable
the hardware NAND logic.
(Patch from Sascha Erlacher)
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Core support of the Atmel SSC library for all Atmel AT91 processors.
Based on David Brownell's initial patch for the AT91RM9200.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace hard-coded DMA mask (0xffffffff) with DMA_BIT_MASK(32) as
defined in dma-mapping.h.
Set "dma_mask" field for the UART platform_devices.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add platform_device and initialization for the RTT (Real Time Timer)
and WDT (Watchdog) integrated in the Atmel AT91SAM9 processors.
For SAM9263, register both RTT peripherals.
[From: David Brownell <dbrownell@users.sourceforge.net>]
Provide platform_resources for RTT peripherals
[From: David Brownell <dbrownell@users.sourceforge.net>]
Add support for RTC peripheral on AT91SAM9RL (same RTC peripherals as
AT91RM9200)
[From: David Brownell <dbrownell@users.sourceforge.net>]
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Image Sensor Interface (ISI) peripheral integrated
in the Atmel AT91SAM9263 processor.
Patch from MaLiK
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for STN LCD displays on Atmel AT91SAM9261-based boards.
Patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On the at92sam9263ek board, tell the MACB driver the IRQ used
by its PHY. This patch is taken from Andrew Victor's 2.6.23-at91
patchset; it matches board schematics. (But it's currently a NOP
since the MACB driver doesn't yet use PHY irqs.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This makes HZ configurable on AT91, following the model used on OMAP.
It defaults to a power of two on AT91rm9200 chips, avoiding rounding
errors which come from dividing a 32 KiHz clock to generate scheduler
irqs; and uses 100 on AT91sam926x chips, using MCK/16 (multi-MHZ).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Remy Bhmer <linux@bohmer.net>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Slight tweaking of the default interrupt priorities (AIC) for the
integrated peripherals on the AT91RM9200, AT91SAM9260, AT91SAM9261 and
AT91SAM9263 processors.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
AT91RM9200 needlessly verifies machine-type numbers of
supported / known platforms and overwrites it for unknown
ones. Remove it.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add STN LCD support on the Atmel AT91SAM9261-EK board.
Uses a black and white screen from Hitachi: SP06Q002.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a debug interface (if CONFIG_DEBUG_FS is selected) to
display the basic configuration and current state of the GPIO pins on
the Atmel AT91 processors.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
LatencyTOP kernel infrastructure; it measures latencies in the
scheduler and tracks it system wide and per process.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use HR-timers (when available) to deliver an accurate preemption tick.
The regular scheduler tick that runs at 1/HZ can be too coarse when nice
level are used. The fairness system will still keep the cpu utilisation 'fair'
by then delaying the task that got an excessive amount of CPU time but try to
minimize this by delivering preemption points spot-on.
The average frequency of this extra interrupt is sched_latency / nr_latency.
Which need not be higher than 1/HZ, its just that the distribution within the
sched_latency period is important.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Replace all lock_cpu_hotplug/unlock_cpu_hotplug from the kernel and use
get_online_cpus and put_online_cpus instead as it highlights the
refcount semantics in these operations.
The new API guarantees protection against the cpu-hotplug operation, but
it doesn't guarantee serialized access to any of the local data
structures. Hence the changes needs to be reviewed.
In case of pseries_add_processor/pseries_remove_processor, use
cpu_maps_update_begin()/cpu_maps_update_done() as we're modifying the
cpu_present_map there.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
[AVR32] extint: Set initial irq type to low level
[AVR32] extint: change set_irq_type() handling
[AVR32] NMI debugging
[AVR32] constify function pointer tables
[AVR32] ATNGW100: Update defconfig
[AVR32] ATSTK1002: Update defconfig
[AVR32] Kconfig: Choose daughterboard instead of CPU
[AVR32] Add support for ATSTK1003 and ATSTK1004
[AVR32] Clean up external DAC setup code
[AVR32] ATSTK1000: Move gpio-leds setup to setup.c
[AVR32] Add support for AT32AP7001 and AT32AP7002
[AVR32] Provide more CPU information in /proc/cpuinfo and dmesg
[AVR32] Oprofile support
[AVR32] Include instrumentation menu
Disable VGA text console for AVR32 architecture
[AVR32] Enable debugging only when needed
ptrace: Call arch_ptrace_attach() when request=PTRACE_TRACEME
[AVR32] Remove redundant try_to_freeze() call from do_signal()
[AVR32] Drop GFP_COMP for DMA memory allocations
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (125 commits)
[CRYPTO] twofish: Merge common glue code
[CRYPTO] hifn_795x: Fixup container_of() usage
[CRYPTO] cast6: inline bloat--
[CRYPTO] api: Set default CRYPTO_MINALIGN to unsigned long long
[CRYPTO] tcrypt: Make xcbc available as a standalone test
[CRYPTO] xcbc: Remove bogus hash/cipher test
[CRYPTO] xcbc: Fix algorithm leak when block size check fails
[CRYPTO] tcrypt: Zero axbuf in the right function
[CRYPTO] padlock: Only reset the key once for each CBC and ECB operation
[CRYPTO] api: Include sched.h for cond_resched in scatterwalk.h
[CRYPTO] salsa20-asm: Remove unnecessary dependency on CRYPTO_SALSA20
[CRYPTO] tcrypt: Add select of AEAD
[CRYPTO] salsa20: Add x86-64 assembly version
[CRYPTO] salsa20_i586: Salsa20 stream cipher algorithm (i586 version)
[CRYPTO] gcm: Introduce rfc4106
[CRYPTO] api: Show async type
[CRYPTO] chainiv: Avoid lock spinning where possible
[CRYPTO] seqiv: Add select AEAD in Kconfig
[CRYPTO] scatterwalk: Handle zero nbytes in scatterwalk_map_and_copy
[CRYPTO] null: Allow setkey on digest_null
...
David Brownell pointed out a mismatch in the avr32 extint code:
> I noticed a small glitch that's not fixed by this patch: the
> initial type is falling edge, but IRQ_TYPE_NONE is mapped to
> IRQ_TYPE_LEVEL_LOW. Potentially surprising.
Fix it by setting the initial type (and handler) to low level,
matching the meaning of IRQ_TYPE_NONE.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Update the AVR32 EIC code to use the new __set_irq_handler_unlocked()
call, getting rid of one more instance of this widespread problem.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Change the NMI handler to use the die notifier chain to signal anyone
who cares. Add a simple "nmi debugger" which hooks into this chain and
that may dump registers, task state, etc. when it happens.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Remove the CPU selection menu and instead let it be selected by the
board or daughterboard option. Add daughterboard selection for
ATSTK1000 (this was previously determined based on CPU type.)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
ATSTK1003 and ATSTK1004 are CPU daughterboards for ATSTK1000 featuring
the AT32AP7001 and AT32AP7002 CPUs, respectively.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Reduce the ridiculous amount of #ifdef clutter in atstk1002.c a bit by
moving all the extdac stuff into its own function and providing an
empty stub for the case when it isn't wanted.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
There may be other boards than STK1002 that want to use the leds on
STK1000. Move it to stk1000 common code to make it easier to reuse.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
These are derivatives of the AT32AP7000 chip, which means that most of
the code stays the same. Rename a few files, functions, definitions
and config symbols to reflect that they apply to all AP700x chips, and
exclude some platform devices from chips where they aren't present.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Add the following fields to /proc/cpuinfo:
* chip type and revision (from the JTAG chip id)
* cpu MHz (from clk_get_rate())
* features (from the CONFIG0 register)
Also rename "cpu family" to "cpu arch" and "cpu type" to "cpu core" to
remove some ambiguity.
Show chip type and revision at bootup, and clarify that the other
kinds of IDs that we're already printing are for the cpu core and
architecture. Rename "AP7000" to "AP7" since that's the name of the
core.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This adds the necessary architecture code to run oprofile on AVR32
using the performance counters documented by the AVR32 Architecture
Manual.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Philippe Elie <phil.el@wanadoo.fr>
Keep track of processes being debugged (including the kernel itself)
and turn the OCD system on and off as appropriate. Since enabling
debugging turns off some optimizations in the CPU core, this fixes the
issue that enabling KProbes support or simply running a program under
gdbserver will reduce system performance significantly until the next
reboot.
The CPU performance will still be reduced for all processes while a
process is being debugged, but this is a lot better than reducing the
performance forever.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
get_signal_to_deliver() will call try_to_freeze(), so there's no point
in do_signal() doing it as well.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
dma_alloc_coherent wants to split pages after allocation in order to
reduce the memory footprint. This does not work well with GFP_COMP
pages, so drop this flag before allocation.
This patch was forward-ported from BSP 2.0
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
All kobjects require a dynamically allocated name now. We no longer
need to keep track if the name is statically assigned, we can just
unconditionally free() all kobject names on cleanup.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is no need for kobject_unregister() anymore, thanks to Kay's
kobject cleanup changes, so replace all instances of it with
kobject_put().
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This code is really really really broken. So much so that it's almost
impossible to fix with a simple patch, so just comment out the offending
registration with the kobject core, and mark the driver as broken.
The problem is that the code is trying to register a "raw" struct
device, which is not allowed. struct device is only for use within the
driver model. This is being done to try to use the firmware layer which
wants a struct device. To properly fix this, use something easy, like a
platform device, which is a struct device and can be used for this kind
of thing.
Cc: Mikael Starvik <starvik@axis.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stop using kobject_register, as this way we can control the sending of
the uevent properly, after everything is properly initialized.
Cc: Jacob Shin <jacob.shin@amd.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make this kobject dynamic and convert it to not use kobject_register,
which is going away.
Cc: Jacob Shin <jacob.shin@amd.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stop using kobject_register, as this way we can control the sending of
the uevent properly, after everything is properly initialized.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stop using kobject_register, as this way we can control the sending of
the uevent properly, after everything is properly initialized.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Christian Glindkamp
Andrew Victor
David Brownell
Andrew Victor
Guennadi Liakhovetski
Arjan van de Ven
Peter Zijlstra
Gautham R Shenoy
Ingo Molnar
Linus Torvalds
Haavard Skinnemoen
Jan Engelhardt
Kay Sievers
Greg Kroah-Hartman