The omap4 CEC hardware cannot tell a Nack from a Low Drive from an
Arbitration Lost error, so just report a Nack, which is almost
certainly the reason for the error anyway.
This also simplifies the implementation. The only three interrupts
that need to be enabled are:
Transmit Buffer Full/Empty Change event: triggered when the
transmit finished successfully and cleared the buffer.
Receiver FIFO Not Empty event: triggered when a message was received.
Frame Retransmit Count Exceeded event: triggered when a transmit
failed repeatedly, usually due to the message being Nacked. Other
reasons are possible (Low Drive, Arbitration Lost) but there is no
way to know. If this happens the TX buffer needs to be cleared
manually.
While testing various error conditions I noticed that the hardware
can receive messages up to 18 bytes in total, which exceeds the legal
maximum of 16. This could cause a buffer overflow, so we check for
this and constrain the size to 16 bytes.
The old incorrect interrupt handler could cause the CEC framework to
enter into a bad state because it mis-detected the "Start Bit Irregularity
event" as an ARB_LOST transmit error when it actually is a receive error
which should be ignored.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Henrik Austad <haustad@cisco.com>
Tested-by: Henrik Austad <haustad@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We have plenty of global registers and whatnot programmed without
any further locking by the modeset code. Currently non-bocking
modesets are allowed to execute in parallel which could corrupt
said registers.
To avoid the problem let's run all non-blocking modesets on an
ordered workqueue. We still put page flips etc. to system_unbound_wq
allowing page flips on one pipe to execute in parallel with page flips
or a modeset on a another pipe (assuming no known state is shared
between them, at which point they would have been added to the same
atomic commit and serialized that way).
Blocking modesets are already serialized with each other by
connection_mutex, and thus are safe. To serialize them with
non-blocking modesets we just flush the workqueue before executing
blocking modesets.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 94f050246b ("drm/i915: nonblocking commit")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171113133622.8593-1-ville.syrjala@linux.intel.com
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
(cherry picked from commit 757fffcfdf)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Commit 77affa3172 ("drm/i915/psr: Fix compiler warnings for
hsw_psr_disable()") swapped status and control registers while fixing
indentation. The _ctl at the end of the status register name must have to
led to this.
Fixes: 77affa3172 ("drm/i915/psr: Fix compiler warnings for hsw_psr_disable()")
References: https://www.mrc-cbu.cam.ac.uk/people/matt.davis/cmabridge/
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171220043520.2599-1-dhinakaran.pandiyan@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 14c6547d6d)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
afs_write_end() is missing page unlock and put if afs_fill_page() fails.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Repeating creation and deletion of a file on an afs mount will run the box
out of memory, e.g.:
dd if=/dev/zero of=/afs/scratch/m0 bs=$((1024*1024)) count=512
rm /afs/scratch/m0
The problem seems to be that it's not properly decrementing the nlink count
so that the inode can be scrapped.
Note that this doesn't fix local creation followed by remote deletion.
That's harder to handle and will require a separate patch as we're not told
that the file has been deleted - only that the directory has changed.
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Smatch warns that:
fs/afs/rxrpc.c:922 afs_extract_data()
error: uninitialized symbol 'remote_abort'.
Smatch is right that "remote_abort" might be uninitialized when we pass
it to afs_set_call_complete(). I don't know if that function uses the
uninitialized variable. Anyway, the comment for rxrpc_kernel_recv_data(),
says that "*_abort should also be initialised to 0." and this patch does
that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Fix the default for fscache_maybe_release_page() for when the cookie isn't
valid or the page isn't cached. It mustn't return false as that indicates
the page cannot yet be freed.
The problem with the default is that if, say, there's no cache, but a
network filesystem's pages are using up almost all the available memory, a
system can OOM because the filesystem ->releasepage() op will not allow
them to be released as fscache_maybe_release_page() incorrectly prevents
it.
This can be tested by writing a sequence of 512MiB files to an AFS mount.
It does not affect NFS or CIFS because both of those wrap the call in a
check of PG_fscache and it shouldn't bother Ceph as that only has
PG_private set whilst writeback is in progress. This might be an issue for
9P, however.
Note that the pages aren't entirely stuck. Removing a file or unmounting
will clear things because that uses ->invalidatepage() instead.
Fixes: 201a15428b ("FS-Cache: Handle pages pending storage that get evicted under OOM conditions")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Tested-by: Marc Dionne <marc.dionne@auristor.com>
cc: stable@vger.kernel.org # 2.6.32+
If userspace attempted to set a "security.capability" xattr shorter than
4 bytes (e.g. 'setfattr -n security.capability -v x file'), then
cap_convert_nscap() read past the end of the buffer containing the xattr
value because it accessed the ->magic_etc field without verifying that
the xattr value is long enough to contain that field.
Fix it by validating the xattr value size first.
This bug was found using syzkaller with KASAN. The KASAN report was as
follows (cleaned up slightly):
BUG: KASAN: slab-out-of-bounds in cap_convert_nscap+0x514/0x630 security/commoncap.c:498
Read of size 4 at addr ffff88002d8741c0 by task syz-executor1/2852
CPU: 0 PID: 2852 Comm: syz-executor1 Not tainted 4.15.0-rc6-00200-gcc0aac99d977 #253
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-20171110_100015-anatol 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:17 [inline]
dump_stack+0xe3/0x195 lib/dump_stack.c:53
print_address_description+0x73/0x260 mm/kasan/report.c:252
kasan_report_error mm/kasan/report.c:351 [inline]
kasan_report+0x235/0x350 mm/kasan/report.c:409
cap_convert_nscap+0x514/0x630 security/commoncap.c:498
setxattr+0x2bd/0x350 fs/xattr.c:446
path_setxattr+0x168/0x1b0 fs/xattr.c:472
SYSC_setxattr fs/xattr.c:487 [inline]
SyS_setxattr+0x36/0x50 fs/xattr.c:483
entry_SYSCALL_64_fastpath+0x18/0x85
Fixes: 8db6c34f1d ("Introduce v3 namespaced file capabilities")
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Serge Hallyn <serge@hallyn.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Pull x86 fixes from Thomas Gleixner:
"A couple of fixlets for x86:
- Fix the ESPFIX double fault handling for 5-level pagetables
- Fix the commandline parsing for 'apic=' on 32bit systems and update
documentation
- Make zombie stack traces reliable
- Fix kexec with stack canary
- Fix the delivery mode for APICs which was missed when the x86
vector management was converted to single target delivery. Caused a
regression due to the broken hardware which ignores affinity
settings in lowest prio delivery mode.
- Unbreak modules when AMD memory encryption is enabled
- Remove an unused parameter of prepare_switch_to"
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Switch all APICs to Fixed delivery mode
x86/apic: Update the 'apic=' description of setting APIC driver
x86/apic: Avoid wrong warning when parsing 'apic=' in X86-32 case
x86-32: Fix kexec with stack canary (CONFIG_CC_STACKPROTECTOR)
x86: Remove unused parameter of prepare_switch_to
x86/stacktrace: Make zombie stack traces reliable
x86/mm: Unbreak modules that use the DMA API
x86/build: Make isoimage work on Debian
x86/espfix/64: Fix espfix double-fault handling on 5-level systems
Pull x86 page table isolation fixes from Thomas Gleixner:
"Four patches addressing the PTI fallout as discussed and debugged
yesterday:
- Remove stale and pointless TLB flush invocations from the hotplug
code
- Remove stale preempt_disable/enable from __native_flush_tlb()
- Plug the memory leak in the write_ldt() error path"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/ldt: Make LDT pgtable free conditional
x86/ldt: Plug memory leak in error path
x86/mm: Remove preempt_disable/enable() from __native_flush_tlb()
x86/smpboot: Remove stale TLB flush invocations
Pull timer fixes from Thomas Gleixner:
"A pile of fixes for long standing issues with the timer wheel and the
NOHZ code:
- Prevent timer base confusion accross the nohz switch, which can
cause unlocked access and data corruption
- Reinitialize the stale base clock on cpu hotplug to prevent subtle
side effects including rollovers on 32bit
- Prevent an interrupt storm when the timer softirq is already
pending caused by tick_nohz_stop_sched_tick()
- Move the timer start tracepoint to a place where it actually makes
sense
- Add documentation to timerqueue functions as they caused confusion
several times now"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timerqueue: Document return values of timerqueue_add/del()
timers: Invoke timer_start_debug() where it makes sense
nohz: Prevent a timer interrupt storm in tick_nohz_stop_sched_tick()
timers: Reinitialize per cpu bases on hotplug
timers: Use deferrable base independent of base::nohz_active
Pull smp fixlet from Thomas Gleixner:
"A trivial build warning fix for newer compilers"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu/hotplug: Move inline keyword at the beginning of declaration
Pull scheduler fixes from Thomas Gleixner:
"Three patches addressing the fallout of the CPU_ISOLATION changes
especially with NO_HZ_FULL plus documentation of boot parameter
dependency"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/isolation: Document boot parameters dependency on CONFIG_CPU_ISOLATION=y
sched/isolation: Enable CONFIG_CPU_ISOLATION=y by default
sched/isolation: Make CONFIG_NO_HZ_FULL select CONFIG_CPU_ISOLATION
Pull perf fixes from Thomas Gleixner:
- plug a memory leak in the intel pmu init code
- clang fixes
- tooling fix to avoid including kernel headers
- a fix for jvmti to generate correct debug information for inlined
code
- replace backtick with a regular shell function
- fix the build in hardened environments
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Plug memory leak in intel_pmu_init()
x86/asm: Allow again using asm.h when building for the 'bpf' clang target
tools arch s390: Do not include header files from the kernel sources
perf jvmti: Generate correct debug information for inlined code
perf tools: Fix up build in hardened environments
perf tools: Use shell function for perl cflags retrieval
Pull irq fixes from Thomas Gleixner:
"A rather large update after the kaisered maintainer finally found time
to handle regression reports.
- The larger part addresses a regression caused by the x86 vector
management rework.
The reservation based model does not work reliably for MSI
interrupts, if they cannot be masked (yes, yet another hw
engineering trainwreck). The reason is that the reservation mode
assigns a dummy vector when the interrupt is allocated and switches
to a real vector when the interrupt is requested.
If the MSI entry cannot be masked then the initialization might
raise an interrupt before the interrupt is requested, which ends up
as spurious interrupt and causes device malfunction and worse. The
fix is to exclude MSI interrupts which do not support masking from
reservation mode and assign a real vector right away.
- Extend the extra lockdep class setup for nested interrupts with a
class for the recently added irq_desc::request_mutex so lockdep can
differeniate and does not emit false positive warnings.
- A ratelimit guard for the bad irq printout so in case a bad irq
comes back immediately the system does not drown in dmesg spam"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/msi, x86/vector: Prevent reservation mode for non maskable MSI
genirq/irqdomain: Rename early argument of irq_domain_activate_irq()
x86/vector: Use IRQD_CAN_RESERVE flag
genirq: Introduce IRQD_CAN_RESERVE flag
genirq/msi: Handle reactivation only on success
gpio: brcmstb: Make really use of the new lockdep class
genirq: Guard handle_bad_irq log messages
kernel/irq: Extend lockdep class for request mutex
Pull objtool fixes from Thomas Gleixner:
"Three fixlets for objtool:
- Address two segfaults related to missing parameter and clang
objects
- Make it compile clean with clang"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Fix seg fault with clang-compiled objects
objtool: Fix seg fault caused by missing parameter
objtool: Fix Clang enum conversion warning
Here are six small fixes of some of the char/misc drivers that have been
sent in to resolve reported issues.
Nothing major, a binder use-after-free fix, some thunderbolt bugfixes, a
hyper-v bugfix, and an nvmem driver fix. All of these have been in
linux-next with no reported issues for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWkjKDw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymkNACgmepGEvd9OJKji+rDj8ADo8lJ7BwAoLiCO22P
wwwpJ7gWnt8N2Red6xcO
=Jmx1
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are six small fixes of some of the char/misc drivers that have
been sent in to resolve reported issues.
Nothing major, a binder use-after-free fix, some thunderbolt bugfixes,
a hyper-v bugfix, and an nvmem driver fix. All of these have been in
linux-next with no reported issues for a while"
* tag 'char-misc-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
nvmem: meson-mx-efuse: fix reading from an offset other than 0
binder: fix proc->files use-after-free
vmbus: unregister device_obj->channels_kset
thunderbolt: Mask ring interrupt properly when polling starts
MAINTAINERS: Add thunderbolt.rst to the Thunderbolt driver entry
thunderbolt: Make pathname to force_power shorter
Here are 2 driver core fixes for 4.15-rc6, resolving some reported
issues.
The first is a cacheinfo fix for DT based systems to resolve a reported
issue that has been around for a while, and the other is to resolve a
regression in the kobject uevent code that showed up in 4.15-rc1.
Both have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWkjLCA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk6GACbBZ/EqSrd5w6//4okaHJLPAi8ligAoNfcBqrH
TPQycbostUcOBHUvvoUB
=MaZG
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are two driver core fixes for 4.15-rc6, resolving some reported
issues.
The first is a cacheinfo fix for DT based systems to resolve a
reported issue that has been around for a while, and the other is to
resolve a regression in the kobject uevent code that showed up in
4.15-rc1.
Both have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kobject: fix suppressing modalias in uevents delivered over netlink
drivers: base: cacheinfo: fix cache type for non-architected system cache
Here are 3 staging driver fixes for 4.15-rc6
The first resolves a bug in the lustre driver that came about due to a
broken cleanup patch, due to crazy list usage in that codebase. The
remaining two are ion driver fixes, finally getting the CMA interaction
to work properly, resolving two regressions in that area of the code.
All have been in linux-next with no reported issues for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWkjMBA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykc6QCcCbSrA4YMyeAZ+pI2ffpMkxhRaYoAoLRC/6co
j+OHv4J4qpH7uf6rRb5Z
=TNOV
-----END PGP SIGNATURE-----
Merge tag 'staging-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are three staging driver fixes for 4.15-rc6
The first resolves a bug in the lustre driver that came about due to a
broken cleanup patch, due to crazy list usage in that codebase.
The remaining two are ion driver fixes, finally getting the CMA
interaction to work properly, resolving two regressions in that area
of the code.
All have been in linux-next with no reported issues for a while"
* tag 'staging-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: android: ion: Fix dma direction for dma_sync_sg_for_cpu/device
staging: ion: Fix ion_cma_heap allocations
staging: lustre: lnet: Fix recent breakage from list_for_each conversion
Here is a single tty fix for a reported issue that you wrote the patch
for :)
It's been in linux-next for a week or so with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWkjMww8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymoDwCgjdn/W0mM1TvfsHaHpKXxTaIeAt0AoKs2uvG2
ys1xuUzwOS8ZPzVtuuqm
=pnhR
-----END PGP SIGNATURE-----
Merge tag 'tty-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY fix from Greg KH:
"Here is a single tty fix for a reported issue that you wrote the patch
for :)
It's been in linux-next for a week or so with no reported issues"
* tag 'tty-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
n_tty: fix EXTPROC vs ICANON interaction with TIOCINQ (aka FIONREAD)
Here are a number of small USB and PHY driver fixes for 4.15-rc6.
Nothing major, but there are a number of regression fixes in here that
resolve issues that have been reported a bunch. There are also the
usual xhci fixes as well as a number of new usb serial device ids.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWkjNXg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykePwCgmTX2oVnGPIagWmm3dsRqr9Fk/uoAoJxGIS00
o/9JAe9k7KvbaurQLjl2
=wAfU
-----END PGP SIGNATURE-----
Merge tag 'usb-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY fixes from Greg KH:
"Here are a number of small USB and PHY driver fixes for 4.15-rc6.
Nothing major, but there are a number of regression fixes in here that
resolve issues that have been reported a bunch. There are also the
usual xhci fixes as well as a number of new usb serial device ids.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: xhci: Add XHCI_TRUST_TX_LENGTH for Renesas uPD720201
xhci: Fix use-after-free in xhci debugfs
xhci: Fix xhci debugfs NULL pointer dereference in resume from hibernate
USB: serial: ftdi_sio: add id for Airbus DS P8GR
usb: Add device quirk for Logitech HD Pro Webcam C925e
usb: add RESET_RESUME for ELSA MicroLink 56K
usbip: fix usbip bind writing random string after command in match_busid
usbip: stub_rx: fix static checker warning on unnecessary checks
usbip: prevent leaking socket pointer address in messages
usbip: stub: stop printing kernel pointer addresses in messages
usbip: vhci: stop printing kernel pointer addresses in messages
USB: Fix off by one in type-specific length check of BOS SSP capability
USB: serial: option: adding support for YUGA CLM920-NC5
phy: rcar-gen3-usb2: select USB_COMMON
phy: rockchip-typec: add pm_runtime_disable in err case
phy: cpcap-usb: Fix platform_get_irq_byname's error checking.
phy: tegra: fix device-tree node lookups
USB: serial: qcserial: add Sierra Wireless EM7565
USB: serial: option: add support for Telit ME910 PID 0x1101
USB: chipidea: msm: fix ulpi-node lookup
The blackfin architecture has seen no maintainer action of any kind since
April 2015. No new code, no pull requests, no acks to patches, no response
to mails, nothing.
The web site has an expired certificate (expiration Sep 2017, issued in
2013), the mailing list sees no answers either, with one exception:
https://sourceforge.net/p/adi-buildroot/mailman/adi-buildroot-devel/
>
> Steven is no longer working on this for ADI. Acked by me if this works. Thanks.
>
> Best regards,
> Aaron Wu
> Analog Devices Inc.
But, Aaron doesn't seem to respond to queries either.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull sparc bugfix from David Miller.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: repair calling incorrect hweight function from stubs
Andy prefers to be paranoid about the pagetable free in the error path of
write_ldt(). Make it conditional and warn whenever the installment of a
secondary LDT fails.
Requested-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The error path in write_ldt() tries to free 'old_ldt' instead of the newly
allocated 'new_ldt', resulting in a memory leak. It also misses to clean up a
half populated LDT pagetable, which is not a leak as it gets cleaned up
when the process exits.
Free both the potentially half populated LDT pagetable and the newly
allocated LDT struct. This can be done unconditionally because once an LDT
is mapped subsequent maps will succeed, because the PTE page is already
populated and the two LDTs fit into that single page.
Reported-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linuxfoundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Fixes: f55f0501cb ("x86/pti: Put the LDT in its own PGD if PTI is on")
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1712311121340.1899@nanos
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The preempt_disable/enable() pair in __native_flush_tlb() was added in
commit:
5cf0791da5 ("x86/mm: Disable preemption during CR3 read+write")
... to protect the UP variant of flush_tlb_mm_range().
That preempt_disable/enable() pair should have been added to the UP variant
of flush_tlb_mm_range() instead.
The UP variant was removed with commit:
ce4a4e565f ("x86/mm: Remove the UP asm/tlbflush.h code, always use the (formerly) SMP code")
... but the preempt_disable/enable() pair stayed around.
The latest change to __native_flush_tlb() in commit:
6fd166aae7 ("x86/mm: Use/Fix PCID to optimize user/kernel switches")
... added an access to a per CPU variable outside the preempt disabled
regions, which makes no sense at all. __native_flush_tlb() must always
be called with at least preemption disabled.
Remove the preempt_disable/enable() pair and add a WARN_ON_ONCE() to catch
bad callers independent of the smp_processor_id() debugging.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linuxfoundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20171230211829.679325424@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
smpboot_setup_warm_reset_vector() and smpboot_restore_warm_reset_vector()
invoke local_flush_tlb() for no obvious reason.
Digging in history revealed that the original code in the 2.1 era added
those because the code manipulated a swapper_pg_dir pagetable entry. The
pagetable manipulation was removed long ago in the 2.3 timeframe, but the
TLB flush invocations stayed around forever.
Remove them along with the pointless pr_debug()s which come from the same 2.1
change.
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linuxfoundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20171230211829.586548655@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Two simple fixes, both of which cause I/O hangs. The storvsc one is
from the hyper-v which can hang under certain hot add/remove
conditions and the other is generally, where removing a target and a
device in close proximity can result in the release method being
executed twice (and subsequent list and other corruption and an
eventual panic).
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Dqbu
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two simple fixes, both of which cause I/O hangs.
The storvsc one is from the hyper-v which can hang under certain hot
add/remove conditions and the other is generally, where removing a
target and a device in close proximity can result in the release
method being executed twice (and subsequent list and other corruption
and an eventual panic)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: storvsc: Fix scsi_cmd error assignments in storvsc_handle_error
scsi: core: check for device state in __scsi_remove_target()
Fix a seg fault which happens when an input file provided to 'objtool
orc generate' doesn't have a '.shstrtab' section (for instance, object
files produced by clang don't have this section).
Signed-off-by: Simon Ser <contact@emersion.fr>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/c0f2231683e9bed40fac1f13ce2c33b8389854bc.1514666459.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix a seg fault when no parameter is provided to 'objtool orc'.
Signed-off-by: Simon Ser <contact@emersion.fr>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/9172803ec7ebb72535bcd0b7f966ae96d515968e.1514666459.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull HID fixes from Jiri Kosina:
- two cosmetic fixes from Daniel Axtens and Hans de Goede
- fix for I2C command mismatch fix for cp2112 driver from Eudean Sun
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: core: lower log level for unknown main item tags to warnings
HID: holtekff: move MODULE_* parameters out of #ifdef block
HID: cp2112: Fix I2C_BLOCK_DATA transactions
It appears that hardened gentoo enables "-fstack-check" by default for
gcc.
That doesn't work _at_all_ for the kernel, because the kernel stack
doesn't act like a user stack at all: it's much smaller, and it doesn't
auto-expand on use. So the extra "probe one page below the stack" code
generated by -fstack-check just breaks the kernel in horrible ways,
causing infinite double faults etc.
[ I have to say, that the particular code gcc generates looks very
stupid even for user space where it works, but that's a separate
issue. ]
Reported-and-tested-by: Alexander Tsoy <alexander@tsoy.me>
Reported-and-tested-by: Toralf Förster <toralf.foerster@gmx.de>
Cc: stable@kernel.org
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86 page table isolation updates from Thomas Gleixner:
"This is the final set of enabling page table isolation on x86:
- Infrastructure patches for handling the extra page tables.
- Patches which map the various bits and pieces which are required to
get in and out of user space into the user space visible page
tables.
- The required changes to have CR3 switching in the entry/exit code.
- Optimizations for the CR3 switching along with documentation how
the ASID/PCID mechanism works.
- Updates to dump pagetables to cover the user space page tables for
W+X scans and extra debugfs files to analyze both the kernel and
the user space visible page tables
The whole functionality is compile time controlled via a config switch
and can be turned on/off on the command line as well"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
x86/ldt: Make the LDT mapping RO
x86/mm/dump_pagetables: Allow dumping current pagetables
x86/mm/dump_pagetables: Check user space page table for WX pages
x86/mm/dump_pagetables: Add page table directory to the debugfs VFS hierarchy
x86/mm/pti: Add Kconfig
x86/dumpstack: Indicate in Oops whether PTI is configured and enabled
x86/mm: Clarify the whole ASID/kernel PCID/user PCID naming
x86/mm: Use INVPCID for __native_flush_tlb_single()
x86/mm: Optimize RESTORE_CR3
x86/mm: Use/Fix PCID to optimize user/kernel switches
x86/mm: Abstract switching CR3
x86/mm: Allow flushing for future ASID switches
x86/pti: Map the vsyscall page if needed
x86/pti: Put the LDT in its own PGD if PTI is on
x86/mm/64: Make a full PGD-entry size hole in the memory map
x86/events/intel/ds: Map debug buffers in cpu_entry_area
x86/cpu_entry_area: Add debugstore entries to cpu_entry_area
x86/mm/pti: Map ESPFIX into user space
x86/mm/pti: Share entry text PMD
x86/entry: Align entry text section to PMD boundary
...
The return values of timerqueue_add/del() are not documented in the kernel doc
comment. Add proper documentation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: rt@linutronix.de
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Link: https://lkml.kernel.org/r/20171222145337.872681338@linutronix.de
The timer start debug function is called before the proper timer base is
set. As a consequence the trace data contains the stale CPU and flags
values.
Call the debug function after setting the new base and flags.
Fixes: 500462a9de ("timers: Switch to a non-cascading wheel")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: stable@vger.kernel.org
Cc: rt@linutronix.de
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Link: https://lkml.kernel.org/r/20171222145337.792907137@linutronix.de
The conditions in irq_exit() to invoke tick_nohz_irq_exit() which
subsequently invokes tick_nohz_stop_sched_tick() are:
if ((idle_cpu(cpu) && !need_resched()) || tick_nohz_full_cpu(cpu))
If need_resched() is not set, but a timer softirq is pending then this is
an indication that the softirq code punted and delegated the execution to
softirqd. need_resched() is not true because the current interrupted task
takes precedence over softirqd.
Invoking tick_nohz_irq_exit() in this case can cause an endless loop of
timer interrupts because the timer wheel contains an expired timer, but
softirqs are not yet executed. So it returns an immediate expiry request,
which causes the timer to fire immediately again. Lather, rinse and
repeat....
Prevent that by adding a check for a pending timer soft interrupt to the
conditions in tick_nohz_stop_sched_tick() which avoid calling
get_next_timer_interrupt(). That keeps the tick sched timer on the tick and
prevents a repetitive programming of an already expired timer.
Reported-by: Sebastian Siewior <bigeasy@linutronix.d>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1712272156050.2431@nanos
The timer wheel bases are not (re)initialized on CPU hotplug. That leaves
them with a potentially stale clk and next_expiry valuem, which can cause
trouble then the CPU is plugged.
Add a prepare callback which forwards the clock, sets next_expiry to far in
the future and reset the control flags to a known state.
Set base->must_forward_clk so the first timer which is queued will try to
forward the clock to current jiffies.
Fixes: 500462a9de ("timers: Switch to a non-cascading wheel")
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1712272152200.2431@nanos
During boot and before base::nohz_active is set in the timer bases, deferrable
timers are enqueued into the standard timer base. This works correctly as
long as base::nohz_active is false.
Once it base::nohz_active is set and a timer which was enqueued before that
is accessed the lock selector code choses the lock of the deferred
base. This causes unlocked access to the standard base and in case the
timer is removed it does not clear the pending flag in the standard base
bitmap which causes get_next_timer_interrupt() to return bogus values.
To prevent that, the deferrable timers must be enqueued in the deferrable
base, even when base::nohz_active is not set. Those deferrable timers also
need to be expired unconditional.
Fixes: 500462a9de ("timers: Switch to a non-cascading wheel")
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: stable@vger.kernel.org
Cc: rt@linutronix.de
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Link: https://lkml.kernel.org/r/20171222145337.633328378@linutronix.de
The new reservation mode for interrupts assigns a dummy vector when the
interrupt is allocated and assigns a real vector when the interrupt is
requested. The reservation mode prevents vector pressure when devices with
a large amount of queues/interrupts are initialized, but only a minimal
subset of those queues/interrupts is actually used.
This mode has an issue with MSI interrupts which cannot be masked. If the
driver is not careful or the hardware emits an interrupt before the device
irq is requestd by the driver then the interrupt ends up on the dummy
vector as a spurious interrupt which can cause malfunction of the device or
in the worst case a lockup of the machine.
Change the logic for the reservation mode so that the early activation of
MSI interrupts checks whether:
- the device is a PCI/MSI device
- the reservation mode of the underlying irqdomain is activated
- PCI/MSI masking is globally enabled
- the PCI/MSI device uses either MSI-X, which supports masking, or
MSI with the maskbit supported.
If one of those conditions is false, then clear the reservation mode flag
in the irq data of the interrupt and invoke irq_domain_activate_irq() with
the reserve argument cleared. In the x86 vector code, clear the can_reserve
flag in the vector allocation data so a subsequent free_irq() won't create
the same situation again. The interrupt stays assigned to a real vector
until pci_disable_msi() is invoked and all allocations are undone.
Fixes: 4900be8360 ("x86/vector/msi: Switch to global reservation mode")
Reported-by: Alexandru Chirvasitu <achirvasub@gmail.com>
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexandru Chirvasitu <achirvasub@gmail.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Mikael Pettersson <mikpelinux@gmail.com>
Cc: Josh Poulson <jopoulso@microsoft.com>
Cc: Mihai Costache <v-micos@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-pci@vger.kernel.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: devel@linuxdriverproject.org
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sakari Ailus <sakari.ailus@intel.com>,
Cc: linux-media@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1712291406420.1899@nanos
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1712291409460.1899@nanos
The 'early' argument of irq_domain_activate_irq() is actually used to
denote reservation mode. To avoid confusion, rename it before abuse
happens.
No functional change.
Fixes: 7249164346 ("genirq/irqdomain: Update irq_domain_ops.activate() signature")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alexandru Chirvasitu <achirvasub@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Mikael Pettersson <mikpelinux@gmail.com>
Cc: Josh Poulson <jopoulso@microsoft.com>
Cc: Mihai Costache <v-micos@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-pci@vger.kernel.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: devel@linuxdriverproject.org
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sakari Ailus <sakari.ailus@intel.com>,
Cc: linux-media@vger.kernel.org
Set the new CAN_RESERVE flag when the initial reservation for an interrupt
happens. The flag is used in a subsequent patch to disable reservation mode
for a certain class of MSI devices.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexandru Chirvasitu <achirvasub@gmail.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Mikael Pettersson <mikpelinux@gmail.com>
Cc: Josh Poulson <jopoulso@microsoft.com>
Cc: Mihai Costache <v-micos@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-pci@vger.kernel.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: devel@linuxdriverproject.org
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sakari Ailus <sakari.ailus@intel.com>,
Cc: linux-media@vger.kernel.org
Add a new flag to mark interrupts which can use reservation mode. This is
going to be used in subsequent patches to disable reservation mode for a
certain class of MSI devices.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexandru Chirvasitu <achirvasub@gmail.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Mikael Pettersson <mikpelinux@gmail.com>
Cc: Josh Poulson <jopoulso@microsoft.com>
Cc: Mihai Costache <v-micos@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-pci@vger.kernel.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: devel@linuxdriverproject.org
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sakari Ailus <sakari.ailus@intel.com>,
Cc: linux-media@vger.kernel.org
When analyzing the fallout of the x86 vector allocation rework it turned
out that the error handling in msi_domain_alloc_irqs() is broken.
If MSI_FLAG_MUST_REACTIVATE is set for a MSI domain then it clears the
activation flag for a successfully initialized msi descriptor. If a
subsequent initialization fails then the error handling code path does not
deactivate the interrupt because the activation flag got cleared.
Move the clearing of the activation flag outside of the initialization loop
so that an eventual failure can be cleaned up correctly.
Fixes: 22d0b12f35 ("genirq/irqdomain: Add force reactivation flag to irq domains")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexandru Chirvasitu <achirvasub@gmail.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Mikael Pettersson <mikpelinux@gmail.com>
Cc: Josh Poulson <jopoulso@microsoft.com>
Cc: Mihai Costache <v-micos@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-pci@vger.kernel.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: devel@linuxdriverproject.org
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sakari Ailus <sakari.ailus@intel.com>,
Cc: linux-media@vger.kernel.org
This fixes a schedutil cpufreq governor regression from the 4.14
cycle that may cause a CPU idleness check to return incorrect results
in some cases which leads to suboptimal decisions (Joel Fernandes).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=TPkr
-----END PGP SIGNATURE-----
Merge tag 'pm-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"This fixes a schedutil cpufreq governor regression from the 4.14 cycle
that may cause a CPU idleness check to return incorrect results in
some cases which leads to suboptimal decisions (Joel Fernandes)"
* tag 'pm-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: schedutil: Use idle_calls counter of the remote CPU
The recent extension of irq_set_lockdep_class() with a second argument
added the new lockdep class to the mrcmstb driver, but used the already
existing lockdep class as second argument, which leaves the new lockdep
class defined but unused.
Use the new lockdep class as that's what the change intended to do.
Fixes: 39c3fd5895 ("kernel/irq: Extend lockdep class for request mutex")
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: linus.walleij@linaro.org
Some of the APIC incarnations are operating in lowest priority delivery
mode. This worked as long as the vector management code allocated the same
vector on all possible CPUs for each interrupt.
Lowest priority delivery mode does not necessarily respect the affinity
setting and may redirect to some other online CPU. This was documented
somewhere in the old code and the conversion to single target delivery
missed to update the delivery mode of the affected APIC drivers which
results in spurious interrupts on some of the affected CPU/Chipset
combinations.
Switch the APIC drivers over to Fixed delivery mode and remove all
leftovers of lowest priority delivery mode.
Switching to Fixed delivery mode is not a problem on these CPUs because the
kernel already uses Fixed delivery mode for IPIs. The reason for this is
that th SDM explicitely forbids lowest prio mode for IPIs. The reason is
obvious: If the irq routing does not honor destination targets in lowest
prio mode then an IPI targeted at CPU1 might end up on CPU0, which would be
a fatal problem in many cases.
As a consequence of this change, the apic::irq_delivery_mode field is now
pointless, but this needs to be cleaned up in a separate patch.
Fixes: fdba46ffb4 ("x86/apic: Get rid of multi CPU affinity")
Reported-by: vcaputo@pengaru.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: vcaputo@pengaru.com
Cc: Pavel Machek <pavel@ucw.cz>
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1712281140440.1688@nanos
Hans Verkuil
Randy Dunlap
Ville Syrjälä
Dhinakaran Pandiyan
John Sperbeck
David Howells
Dan Carpenter
Eric Biggers
Linus Torvalds
Adam Borowski
Thomas Gleixner
Simon Ser
Anna-Maria Gleixner