On devices that support TC U32 offloads, this flag enables a filter to be
added only to HW. skip-sw and skip-hw are mutually exclusive flags. By
default without any flags, the filter is added to both HW and SW, but no
error checks are done in case of failure to add to HW. With skip-sw,
failure to add to HW is treated as an error.
Here is a sample script that adds 2 filters, one with skip-sw and the other
with skip-hw flag.
# add ingress qdisc
tc qdisc add dev p4p1 ingress
# enable hw tc offload.
ethtool -K p4p1 hw-tc-offload on
# add u32 filter with skip-sw flag.
tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:1 u32 ht 800: flowid 800:1 \
skip-sw \
match ip src 192.168.1.0/24 \
action drop
# add u32 filter with skip-hw flag.
tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:2 u32 ht 800: flowid 800:2 \
skip-hw \
match ip src 192.168.2.0/24 \
action drop
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_conntrack_core.c fix in 'net' is not relevant in 'net-next'
because we no longer have a per-netns conntrack hash.
The ip_gre.c conflict as well as the iwlwifi ones were cases of
overlapping changes.
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/tx.c
net/ipv4/ip_gre.c
net/netfilter/nf_conntrack_core.c
Signed-off-by: David S. Miller <davem@davemloft.net>
* completion and fixups of nla_put_64_64bit() work
* remove a/b/g/n from wext nickname to avoid confusion
with 11ac (which wouldn't even fit fully there due to
string length restrictions)
along with some other minor changes/cleanups.
-----BEGIN PGP SIGNATURE-----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=QNxF
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-05-12' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Some more work for 4.7, notably:
* completion and fixups of nla_put_64_64bit() work
* remove a/b/g/n from wext nickname to avoid confusion
with 11ac (which wouldn't even fit fully there due to
string length restrictions)
along with some other minor changes/cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an initial implementation of a netdev driver for GTP datapath
(GTP-U) v0 and v1, according to the GSM TS 09.60 and 3GPP TS 29.060
standards. This tunneling protocol is used to prevent subscribers from
accessing mobile carrier core network infrastructure.
This implementation requires a GGSN userspace daemon that implements the
signaling protocol (GTP-C), such as OpenGGSN [1]. This userspace daemon
updates the PDP context database that represents active subscriber
sessions through a genetlink interface.
For more context on this tunneling protocol, you can check the slides
that were presented during the NetDev 1.1 [2].
Only IPv4 is supported at this time.
[1] http://git.osmocom.org/openggsn/
[2] http://www.netdevconf.org/1.1/proceedings/slides/schultz-welte-osmocom-gtp.pdf
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
glibc's net/if.h contains copies of definitions from linux/if.h and these
conflict and cause build failures if both files are included by application
source code. Changes in uapi headers, which fixed header file dependencies to
include linux/if.h when it was needed, e.g. commit 1ffad83d, made the
net/if.h and linux/if.h incompatibilities visible as build failures for
userspace applications like iproute2 and xtables-addons.
This patch fixes compile errors when glibc net/if.h is included before
linux/if.h:
./linux/if.h:99:21: error: redeclaration of enumerator ‘IFF_NOARP’
./linux/if.h:98:23: error: redeclaration of enumerator ‘IFF_RUNNING’
./linux/if.h:97:26: error: redeclaration of enumerator ‘IFF_NOTRAILERS’
./linux/if.h:96:27: error: redeclaration of enumerator ‘IFF_POINTOPOINT’
./linux/if.h:95:24: error: redeclaration of enumerator ‘IFF_LOOPBACK’
./linux/if.h:94:21: error: redeclaration of enumerator ‘IFF_DEBUG’
./linux/if.h:93:25: error: redeclaration of enumerator ‘IFF_BROADCAST’
./linux/if.h:92:19: error: redeclaration of enumerator ‘IFF_UP’
./linux/if.h:252:8: error: redefinition of ‘struct ifconf’
./linux/if.h:203:8: error: redefinition of ‘struct ifreq’
./linux/if.h:169:8: error: redefinition of ‘struct ifmap’
./linux/if.h:107:23: error: redeclaration of enumerator ‘IFF_DYNAMIC’
./linux/if.h:106:25: error: redeclaration of enumerator ‘IFF_AUTOMEDIA’
./linux/if.h:105:23: error: redeclaration of enumerator ‘IFF_PORTSEL’
./linux/if.h:104:25: error: redeclaration of enumerator ‘IFF_MULTICAST’
./linux/if.h:103:21: error: redeclaration of enumerator ‘IFF_SLAVE’
./linux/if.h:102:22: error: redeclaration of enumerator ‘IFF_MASTER’
./linux/if.h:101:24: error: redeclaration of enumerator ‘IFF_ALLMULTI’
./linux/if.h💯23: error: redeclaration of enumerator ‘IFF_PROMISC’
The cases where linux/if.h is included before net/if.h need a similar fix in
the glibc side, or the order of include files can be changed userspace
code as a workaround.
This change was tested in x86 userspace on Debian unstable with
scripts/headers_compile_test.sh:
$ make headers_install && \
cd usr/include && ../../scripts/headers_compile_test.sh -l -k
...
cc -Wall -c -nostdinc -I /usr/lib/gcc/i586-linux-gnu/5/include -I /usr/lib/gcc/i586-linux-gnu/5/include-fixed -I . -I /home/mcfrisk/src/linux-2.6/usr/headers_compile_test_include.2uX2zH -I /home/mcfrisk/src/linux-2.6/usr/headers_compile_test_include.2uX2zH/i586-linux-gnu -o /dev/null ./linux/if.h_libc_before_kernel.h
PASSED libc before kernel test: ./linux/if.h
Reported-by: Jan Engelhardt <jengelh@inai.de>
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Reported-by: Stephen Hemminger <shemming@brocade.com>
Reported-by: Waldemar Brodkorb <mail@waldemar-brodkorb.de>
Cc: Gabriel Laskar <gabriel@lse.epita.fr>
Signed-off-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
In netdevice.h we removed the structure in net-next that is being
changes in 'net'. In macsec.c and rtnetlink.c we have overlaps
between fixes in 'net' and the u64 attribute changes in 'net-next'.
The mlx5 conflicts have to do with vxlan support dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Check klogctl failure correctly, from Colin Ian King.
2) Prevent OOM when under memory pressure in flowcache, from Steffen
Klassert.
3) Fix info leak in llc and rtnetlink ifmap code, from Kangjie Lu.
4) Memory barrier and multicast handling fixes in bnxt_en, from Michael
Chan.
5) Endianness bug in mlx5, from Daniel Jurgens.
6) Fix disconnect handling in VSOCK, from Ian Campbell.
7) Fix locking of netdev list walking in get_bridge_ifindices(), from
Nikolay Aleksandrov.
8) Bridge multicast MLD parser can look at wrong packet offsets, fix
from Linus Lüssing.
9) Fix chip hang in qede driver, from Sudarsana Reddy Kalluru.
10) Fix missing setting of encapsulation before inner handling completes
in udp_offload code, from Jarno Rajahalme.
11) Missing rollbacks during LAG join and flood configuration failures
in mlxsw driver, from Ido Schimmel.
12) Fix error code checks in netxen driver, from Dan Carpenter.
13) Fix key size in new macsec driver, from Sabrina Dubroca.
14) Fix mlx5/VXLAN dependencies, from Arnd Bergmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (29 commits)
net/mlx5e: make VXLAN support conditional
Revert "net/mlx5: Kconfig: Fix MLX5_EN/VXLAN build issue"
macsec: key identifier is 128 bits, not 64
Documentation/networking: more accurate LCO explanation
macvtap: segmented packet is consumed
tools: bpf_jit_disasm: check for klogctl failure
qede: uninitialized variable in qede_start_xmit()
netxen: netxen_rom_fast_read() doesn't return -1
netxen: reversed condition in netxen_nic_set_link_parameters()
netxen: fix error handling in netxen_get_flash_block()
mlxsw: spectrum: Add missing rollback in flood configuration
mlxsw: spectrum: Fix rollback order in LAG join failure
udp_offload: Set encapsulation before inner completes.
udp_tunnel: Remove redundant udp_tunnel_gro_complete().
qede: prevent chip hang when increasing channels
net: ipv6: tcp reset, icmp need to consider L3 domain
bridge: fix igmp / mld query parsing
net: bridge: fix old ioctl unlocked net device walk
VSOCK: do not disconnect socket when peer has shutdown SEND only
net/mlx4_en: Fix endianness bug in IPV6 csum calculation
...
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following large patchset contains Netfilter updates for your
net-next tree. My initial intention was to send you this in two goes but
when I looked back twice I already had this burden on top of me.
Several updates for IPVS from Marco Angaroni:
1) Allow SIP connections originating from real-servers to be load
balanced by the SIP persistence engine as is already implemented
in the other direction.
2) Release connections immediately for One-packet-scheduling (OPS)
in IPVS, instead of making it via timer and rcu callback.
3) Skip deleting conntracks for each one packet in OPS, and don't call
nf_conntrack_alter_reply() since no reply is expected.
4) Enable drop on exhaustion for OPS + SIP persistence.
Miscelaneous conntrack updates from Florian Westphal, including fix for
hash resize:
5) Move conntrack generation counter out of conntrack pernet structure
since this is only used by the init_ns to allow hash resizing.
6) Use get_random_once() from packet path to collect hash random seed
instead of our compound.
7) Don't disable BH from ____nf_conntrack_find() for statistics,
use NF_CT_STAT_INC_ATOMIC() instead.
8) Fix lookup race during conntrack hash resizing.
9) Introduce clash resolution on conntrack insertion for connectionless
protocol.
Then, Florian's netns rework to get rid of per-netns conntrack table,
thus we use one single table for them all. There was consensus on this
change during the NFWS 2015 and, on top of that, it has recently been
pointed as a source of multiple problems from unpriviledged netns:
11) Use a single conntrack hashtable for all namespaces. Include netns
in object comparisons and make it part of the hash calculation.
Adapt early_drop() to consider netns.
12) Use single expectation and NAT hashtable for all namespaces.
13) Use a single slab cache for all namespaces for conntrack objects.
14) Skip full table scanning from nf_ct_iterate_cleanup() if the pernet
conntrack counter tells us the table is empty (ie. equals zero).
Fixes for nf_tables interval set element handling, support to set
conntrack connlabels and allow set names up to 32 bytes.
15) Parse element flags from element deletion path and pass it up to the
backend set implementation.
16) Allow adjacent intervals in the rbtree set type for dynamic interval
updates.
17) Add support to set connlabel from nf_tables, from Florian Westphal.
18) Allow set names up to 32 bytes in nf_tables.
Several x_tables fixes and updates:
19) Fix incorrect use of IS_ERR_VALUE() in x_tables, original patch
from Andrzej Hajda.
And finally, miscelaneous netfilter updates such as:
20) Disable automatic helper assignment by default. Note this proc knob
was introduced by a900689264 ("netfilter: nf_ct_helper: allow to
disable automatic helper assignment") 4 years ago to start moving
towards explicit conntrack helper configuration via iptables CT
target.
21) Get rid of obsolete and inconsistent debugging instrumentation
in x_tables.
22) Remove unnecessary check for null after ip6_route_output().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The MACsec standard mentions a key identifier for each key, but
doesn't specify anything about it, so I arbitrarily chose 64 bits.
IEEE 802.1X-2010 specifies MKA (MACsec Key Agreement), and defines the
key identifier to be 128 bits (96 bits "member identifier" + 32 bits
"key number").
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On small embedded routers, one wants to control maximal amount of
memory used by fq_codel, instead of controlling number of packets or
bytes, since GRO/TSO make these not practical.
Assuming skb->truesize is accurate, we have to keep track of
skb->truesize sum for skbs in queue.
This patch adds a new TCA_FQ_CODEL_MEMORY_LIMIT attribute.
I chose a default value of 32 MBytes, which looks reasonable even
for heavy duty usages. (Prior fq_codel users should not be hurt
when they upgrade their kernels)
Two fields are added to tc_fq_codel_qd_stats to report :
- Current memory usage
- Number of drops caused by memory limits
# tc qd replace dev eth1 root est 1sec 4sec fq_codel memory_limit 4M
..
# tc -s -d qd sh dev eth1
qdisc fq_codel 8008: root refcnt 257 limit 10240p flows 1024
quantum 1514 target 5.0ms interval 100.0ms memory_limit 4Mb ecn
Sent 2083566791363 bytes 1376214889 pkt (dropped 4994406, overlimits 0
requeues 21705223)
rate 9841Mbit 812549pps backlog 3906120b 376p requeues 21705223
maxpacket 68130 drop_overlimit 4994406 new_flow_count 28855414
ecn_mark 0 memory_used 4190048 drop_overmemory 4994406
new_flows_len 1 old_flows_len 177
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Dave Täht <dave.taht@gmail.com>
Cc: Sebastian Möller <moeller0@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an implementation of Qualcomm's IPC router protocol, used to
communicate with service providing remote processors.
Signed-off-by: Courtney Cavin <courtney.cavin@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
[bjorn: Cope with 0 being a valid node id and implement RTM_NEWADDR]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extended BPF carried over two instructions from classic to access
packet data: LD_ABS and LD_IND. They're highly optimized in JITs,
but due to their design they have to do length check for every access.
When BPF is processing 20M packets per second single LD_ABS after JIT
is consuming 3% cpu. Hence the need to optimize it further by amortizing
the cost of 'off < skb_headlen' over multiple packet accesses.
One option is to introduce two new eBPF instructions LD_ABS_DW and LD_IND_DW
with similar usage as skb_header_pointer().
The kernel part for interpreter and x64 JIT was implemented in [1], but such
new insns behave like old ld_abs and abort the program with 'return 0' if
access is beyond linear data. Such hidden control flow is hard to workaround
plus changing JITs and rolling out new llvm is incovenient.
Therefore allow cls_bpf/act_bpf program access skb->data directly:
int bpf_prog(struct __sk_buff *skb)
{
struct iphdr *ip;
if (skb->data + sizeof(struct iphdr) + ETH_HLEN > skb->data_end)
/* packet too small */
return 0;
ip = skb->data + ETH_HLEN;
/* access IP header fields with direct loads */
if (ip->version != 4 || ip->saddr == 0x7f000001)
return 1;
[...]
}
This solution avoids introduction of new instructions. llvm stays
the same and all JITs stay the same, but verifier has to work extra hard
to prove safety of the above program.
For XDP the direct store instructions can be allowed as well.
The skb->data is NET_IP_ALIGNED, so for common cases the verifier can check
the alignment. The complex packet parsers where packet pointer is adjusted
incrementally cannot be tracked for alignment, so allow byte access in such cases
and misaligned access on architectures that define efficient_unaligned_access
[1] https://git.kernel.org/cgit/linux/kernel/git/ast/bpf.git/?h=ld_abs_dw
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is another attempt to avoid a regression in wwn_to_u64() after that
started using get_unaligned_be64(), which in turn ran into a bug on
gcc-4.9 through 6.1.
The regression got introduced due to the combination of two separate
workarounds (commits e3bde9568d99: "include/linux/unaligned: force
inlining of byteswap operations" and ef3fb2422ffe: "scsi: fc: use
get/put_unaligned64 for wwn access") that each try to sidestep distinct
problems with gcc behavior (code growth and increased stack usage).
Unfortunately after both have been applied, a more serious gcc bug has
been uncovered, leading to incorrect object code that discards part of a
function and causes undefined behavior.
As part of this problem is how __builtin_constant_p gets evaluated on an
argument passed by reference into an inline function, this avoids the
use of __builtin_constant_p() for all architectures that set
CONFIG_ARCH_USE_BUILTIN_BSWAP. Most architectures do not set
ARCH_SUPPORTS_OPTIMIZED_INLINING, which means they probably do not
suffer from the problem in the qla2xxx driver, but they might still run
into it elsewhere.
Both of the original workarounds were only merged in the 4.6 kernel, and
the bug that is fixed by this patch should only appear if both are
there, so we probably don't need to backport the fix. On the other
hand, it works by simplifying the code path and should not have any
negative effects.
[arnd@arndb.de: fix older gcc warnings]
(http://lkml.kernel.org/r/12243652.bxSxEgjgfk@wuerfel)
Link: https://lkml.org/lkml/headers/2016/4/12/1103
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=66122
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=70232
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=70646
Fixes: e3bde9568d ("include/linux/unaligned: force inlining of byteswap operations")
Fixes: ef3fb2422f ("scsi: fc: use get/put_unaligned64 for wwn access")
Link: http://lkml.kernel.org/r/1780465.XdtPJpi8Tt@wuerfel
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Tested-by: Josh Poimboeuf <jpoimboe@redhat.com> # on gcc-5.3
Tested-by: Quinn Tran <quinn.tran@qlogic.com>
Cc: Martin Jambor <mjambor@suse.cz>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: James Bottomley <James.Bottomley@hansenpartnership.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Jan Hubicka <hubicka@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix problems in uapi definitions reported by Gabriel Laskar: (see
https://lkml.org/lkml/2016/4/5/205 for details)
- move public header file rio_mport_cdev.h to include/uapi/linux directory
- change types in data structures passed as IOCTL parameters
- improve parameter checking in some IOCTL service routines
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Reported-by: Gabriel Laskar <gabriel@lse.epita.fr>
Tested-by: Barry Wood <barry.wood@idt.com>
Cc: Gabriel Laskar <gabriel@lse.epita.fr>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com>
Cc: Barry Wood <barry.wood@idt.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, we support set names of up to 16 bytes, get this aligned
with the maximum length we can use in ipset to make it easier when
considering migration to nf_tables.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
In presence of inelastic flows and stress, we can call
fq_codel_drop() for every packet entering fq_codel qdisc.
fq_codel_drop() is quite expensive, as it does a linear scan
of 4 KB of memory to find a fat flow.
Once found, it drops the oldest packet of this flow.
Instead of dropping a single packet, try to drop 50% of the backlog
of this fat flow, with a configurable limit of 64 packets per round.
TCA_FQ_CODEL_DROP_BATCH_SIZE is the new attribute to make this
limit configurable.
With this strategy the 4 KB search is amortized to a single cache line
per drop [1], so fq_codel_drop() no longer appears at the top of kernel
profile in presence of few inelastic flows.
[1] Assuming a 64byte cache line, and 1024 buckets
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dave Taht <dave.taht@gmail.com>
Cc: Jonathan Morton <chromatix99@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Dave Taht
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new LINK_XSTATS_TYPE_BRIDGE attribute and implement the
RTM_GETSTATS callbacks for IFLA_STATS_LINK_XSTATS (fill_linkxstats and
get_linkxstats_size) in order to export the per-vlan stats.
The paddings were added because soon these fields will be needed for
per-port per-vlan stats (or something else if someone beats me to it) so
avoiding at least a few more netlink attributes.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for per-VLAN Tx/Rx statistics. Every global vlan context gets
allocated a per-cpu stats which is then set in each per-port vlan context
for quick access. The br_allowed_ingress() common function is used to
account for Rx packets and the br_handle_vlan() common function is used
to account for Tx packets. Stats accounting is performed only if the
bridge-wide vlan_stats_enabled option is set either via sysfs or netlink.
A struct hole between vlan_enabled and vlan_proto is used for the new
option so it is in the same cache line. Currently it is binary (on/off)
but it is intentionally restricted to exactly 0 and 1 since other values
will be used in the future for different purposes (e.g. per-port stats).
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add callbacks to calculate the size and fill link extended statistics
which can be split into multiple messages and are dumped via the new
rtnl stats API (RTM_GETSTATS) with the IFLA_STATS_LINK_XSTATS attribute.
Also add that attribute to the idx mask check since it is expected to
be able to save state and resume dumping (e.g. future bridge per-vlan
stats will be dumped via this attribute and callbacks).
Each link type should nest its private attributes under the per-link type
attribute. This allows to have any number of separated private attributes
and to avoid one call to get the dev link type.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define PPP device handler for use with rtnetlink.
The only PPP specific attribute is IFLA_PPP_DEV_FD. It is mandatory and
contains the file descriptor of the associated /dev/ppp instance (the
file descriptor which would have been used for ioctl(PPPIOCNEWUNIT) in
the ioctl-based API). The PPP device is removed when this file
descriptor is released (same behaviour as with ioctl based PPP
devices).
PPP devices created with the rtnetlink API behave like the ones created
with ioctl(PPPIOCNEWUNIT). In particular existing ioctls work the same
way, no matter how the PPP device was created.
The rtnl callbacks are also assigned to ioctl based PPP devices. This
way, rtnl messages have the same effect on any PPP devices.
The immediate effect is that all PPP devices, even ioctl-based
ones, can now be removed with "ip link del".
A minor difference still exists between ioctl and rtnl based PPP
interfaces: in the device name, the number following the "ppp" prefix
corresponds to the PPP unit number for ioctl based devices, while it is
just an unrelated incrementing index for rtnl ones.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=REYX
-----END PGP SIGNATURE-----
Merge tag 'media/v4.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Some regression fixes:
- videobuf2 core: avoid the risk of going past buffer on multi-planes
and fix rw mode
- fix support for 4K formats at V4L2 core
- fix a trouble at davinci_fpe, caused by a bad patch
- usbvision: revert a patch with a partial fixup. The fixup patch
was merged already, and this one has some issues"
* tag 'media/v4.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] vb2-memops: Fix over allocation of frame vectors
[media] media: vb2: Fix regression on poll() for RW mode
[media] v4l2-dv-timings.h: fix polarity for 4k formats
[media] davinci_vpfe: Revert "staging: media: davinci_vpfe: remove,unnecessary ret variable"
[media] usbvision: revert commit 588afcc1
[media] videobuf2-v4l2: Verify planes array in buffer dequeueing
[media] videobuf2-core: Check user space planes array in dqbuf
Minor overlapping changes in the conflicts.
In the macsec case, the change of the default ID macro
name overlapped with the 64-bit netlink attribute alignment
fixes in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas converted most users, but didn't realize some were generated
by macros. Convert those over as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I also fix commit 8b32ab9e6ef1: use nla_total_size_64bit() for
OVS_FLOW_ATTR_USED in ovs_flow_cmd_msg_size().
Fixes: 8b32ab9e6ef1 ("ovs: use nla_put_u64_64bit()")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I also fix the value of INET_DIAG_MAX. It's wrong since commit 8f840e47f1
which is only in net-next right now, thus I didn't make a separate patch.
Fixes: 8f840e47f1 ("sctp: add the sctp_diag.c file")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 841645b5f2.
Ok, this puts the feature back. I've decided to apply David A.'s
bug fix and run with that rather than make everyone wait another
whole release for this feature.
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas's patch missed this, now generating docbook warnings.
Add the missing descriptions to address that.
Fixes: 2dad624e6d ("wireless: use nla_put_u64_64bit()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for the a station statistics netlink attribute:
NL80211_STA_INFO_RX_DURATION.
If present, this attribute contains the aggregate PPDU duration (in
microseconds) for all the frames from the peer. This is useful to
help understand the total time spent transmitting to us by all of
the connected peers.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support checksum neutral ILA as described in the ILA draft. The low
order 16 bits of the identifier are used to contain the checksum
adjustment value.
The csum-mode parameter is added to described checksum processing. There
are three values:
- adjust transport checksum (previous behavior)
- do checksum neutral mapping
- do nothing
On output the csum-mode in the ila_params is checked and acted on. If
mode is checksum neutral mapping then to mapping and set C-bit.
On input, C-bit is checked. If it is set checksum-netural mapping is
done (regardless of csum-mode in ila params) and C-bit will be cleared.
If it is not set then action in csum-mode is taken.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts the following three commits:
70af921db6799977d9aaf1705ec197
The feature was ill conceived, has terrible semantics, and has added
nothing but regressions to the already fragile ipv6 stack.
Fixes: f1705ec197 ("net: ipv6: Make address flushing on ifdown optional")
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSync polarity was negative instead of positive for the 4k CEA formats.
I probably copy-and-pasted these from the DMT 4k format, which does have a
negative VSync polarity.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Martin Bugge <marbugge@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.1 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
I accidentally forgot some MACSEC_ prefixes in if_macsec.h.
Fixes: dece8d2b78 ("uapi: add MACsec bits")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
nla_data() is now aligned on a 64-bit area.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nla_data() is now aligned on a 64-bit area.
The temporary function nla_put_be64_32bit() is removed in this patch.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nla_data() is now aligned on a 64-bit area.
A temporary version (nla_put_be64_32bit()) is added for nla_put_net64().
This function is removed in the next patch.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>