Fixups for the ps3 interrupt routines to support all HV device
in a generic way.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In commit 0fba3a1f39 (a very long time ago,
May 2006), I fixed a bug that caused powermacs to crash when you tried
entering standby/mem suspend states.
As I'm now getting more familiar with the suspend code I notice a few
more things:
1. we previously misunderstood what pm_ops is for, it isn't supposed to be
for doing platform dependent suspend/resume stuff that needs to be done
for suspend to disk (as we currently try to use it!), it is instead for
entering platform dependent suspend states ("standby", "mem").
2. due to the first point, we never properly save FPU and altivec states
when suspending to disk. It probably hasn't hurt yet because the process
that writes the "disk" to /sys/power/state uses neither and its context
is used.
This patch addresses these points as follows:
1. remove all pm_ops from powermac, powermac suspend to ram isn't currently
usable via /sys/power/state but is done via the PMU instead.
2. move the code responsible for storing FPU/altivec state into
save_processor_state and the set_context() call to restore_processor_state.
3. add a call to kernel_enable_spe()
It may look like there is some code removal missing but that is
actually because the new suspend.h file overrides the ppc/suspend.h
one which was previously used.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, all 32-bit powerpc platforms use asm-ppc/pgtable.h and
asm-ppc/pgalloc.h, even when otherwise compiled with ARCH=powerpc.
Those asm-ppc files are a fairly nasty tangle of #ifdefs including a
bunch of things which shouldn't be necessary any more in arch/powerpc.
Cleaning up that mess is going to take a while, but this patch is a
first step. It separates the asm-powerpc/pg{alloc,table}.h into 64
bit and 32 bit versions in asm-powerpc, which the basic .h files in
asm-powerpc select based on config. We make a few tiny tweaks to the
innards of the files along the way, making the outermost ifdefs
(double-inclusion protection and __KERNEL__) a little cleaner, and
#including asm-generic/pgtable.h from the top-level
asm-powerpc/pgtable.h (since both the old 32-bit and 64-bit versions
ended with such an #include).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since we don't have it active by default, the STRICT_MM_TYPECHECKS
option has bitrotted again. This patch fixes a couple of simple build
fixes if the option is selected. First, pud_t mustn't be defined in
page.h on 32-bit systems, because it conflicts with the version in the
generic pud-folding code. Second, pci_32.c is missing a __pgprot()
wrapper call. Third, a couple of PS3 files use constants of type
pgprot_t when they need the raw values, we add pgprot_val() calls to
fix this.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch takes the definitions for the PPC44x MMU (a software loaded
TLB) from asm-ppc/mmu.h, cleans them up of things no longer necessary
in arch/powerpc and puts them in a new asm-powerpc/mmu_44x.h file. It
also substantially simplifies arch/powerpc/mm/44x_mmu.c and makes a
couple of small fixes necessary for the 44x MMU code to build and work
properly in arch/powerpc.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is no big reason to have that function inlined.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the powerpc architecture, of_irq_to_resource, currently sitting in
prom.h, needs irq_of_parse_and_map and NO_IRQ from asm-powerpc/irq.h.
The solution suggested by Benjamin Herrenschmidt is to move it to
arch/powerpc/kernel/prom_parse.c.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch makes sure that a caller of pmac_call_feature() won't try
to call into ppc_md.feature_call of another platform, which might
happen if some powermac drivers are loaded on non-powermac machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For backwards compatibility, call_platform_enable_wakeup() can return 0
instead of -EIO since we aren't guaranteed to have errno defined.
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a kvasprintf() function to complement kasprintf().
No in-tree users yet, but I have some coming up.
[akpm@linux-foundation.org: EXPORT it]
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Keir Fraser <keir@xensource.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes the docs and behaviour from "all states valid" to "no
states valid" if no .valid callback is assigned. Users of pm_ops that only
need mem sleep can assign pm_valid_only_mem without any overhead, others
will require more elaborate callbacks.
Now that all users of pm_ops have a .valid callback this is a safe thing to
do and prevents things from getting messy again as they were before.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Looks-okay-to: Rafael J. Wysocki <rjw@sisk.pl>
Cc: <linux-pm@lists.linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Almost all users of pm_ops only support mem sleep, don't check in .valid and
don't reject any others in .prepare so users can be confused if they check
/sys/power/state, especially when new states are added (these would then
result in s-t-r although they're supposed to be something different).
This patch implements a generic pm_valid_only_mem function that is then
exported for users and puts it to use in almost all existing pm_ops.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: linux-pm@lists.linux-foundation.org
Cc: Len Brown <lenb@kernel.org>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the firmware disk suspend mode which is the wrong approach,
it is supposed to be used for implementing firmware-based disk suspend but
cannot actually be used for that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <linux-pm@lists.linux-foundation.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch series cleans up some misconceptions about pm_ops. Some users of
the pm_ops structure attempt to use it to stop the user from entering suspend
to disk, this, however, is not possible since the user can always use
"shutdown" in /sys/power/disk and then the pm_ops are never invoked. Also,
platforms that don't support suspend to disk simply should not allow
configuring SOFTWARE_SUSPEND (read the help text on it, it only selects
suspend to disk and nothing else, all the other stuff depends on PM).
The pm_ops structure is actually intended to provide a way to enter
platform-defined sleep states (currently supported states are "standby" and
"mem" (suspend to ram)) and additionally (if SOFTWARE_SUSPEND is configured)
allows a platform to support a platform specific way to enter low-power mode
once everything has been saved to disk. This is currently only used by ACPI
(S4).
This patch:
The pm_ops.pm_disk_mode is used in totally bogus ways since nobody really
seems to understand what it actually does.
This patch clarifies the pm_disk_mode description.
It also removes all the arm and sh users that think they can veto suspend to
disk via pm_ops; not so since the user can always do echo shutdown >
/sys/power/disk, they need to find a better way involving Kconfig or such.
ACPI is the only user left with a non-zero pm_disk_mode.
The patch also sets the default mode to shutdown again, but when a new pm_ops
is registered its pm_disk_mode is selected as default, that way the default
stays for ACPI where it is apparently required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <linux-pm@lists.linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Today's print_symbol function dumps a kernel symbol with printk. This
patch extends the functionality of kallsyms.c so that the symbol lookup
function may be used without the printk. This is useful for modules that
want to dump symbols elsewhere, for example, to debugfs. I intend to use
the new function call in the GFS2 file system (which will be a separate
patch).
[akpm@linux-foundation.org: build fix]
[clameter@sgi.com: sprint_symbol should return length of string like sprintf]
Signed-off-by: Robert Peterson <rpeterso@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Paulo Marques <pmarques@grupopie.com>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid: (21 commits)
USB HID: don't warn on idVendor == 0
USB HID: add 'quirks' module parameter
USB HID: add support for dynamically-created quirks
USB HID: clarify static quirk handling as squirks
USB HID: encapsulate quirk handling into hid-quirks.c
USB HID: EMS USBII device needs HID_QUIRK_MULTI_INPUT
HID: update copyright and authorship macro
HID: introduce proper zeroing of unused bits in output reports
USB HID: add support for WiseGroup MP-8800 Quad Joypad
USB HID: add FF support for Logitech Force 3D Pro Joystick
USB HID: numlock quirk for dell W7658 keyboard
USB HID: Logitech MX3000 keyboard needs report descriptor quirk
USB HID: extend quirk for Logitech S510 keyboard
USB HID: usbkbd/usbmouse - handle errors when registering devices
USB HID: add QUIRK_HIDDEV for Belkin Flip KVM
HID: enable dead keys on a belkin wireless keyboard
USB HID: Thustmaster firestorm dual power v1 support
USB HID: specify explicit size for hid_blacklist.quirks
USB HID: fix retry & reset logic
USB HID: consolidate vendor/product ids
...
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
[IPV4] SNMP: Support OutMcastPkts and OutBcastPkts
[IPV4] SNMP: Support InMcastPkts and InBcastPkts
[IPV4] SNMP: Support InTruncatedPkts
[IPV4] SNMP: Support InNoRoutes
[SNMP]: Add definitions for {In,Out}BcastPkts
[TCP] FRTO: RFC4138 allows Nagle override when new data must be sent
[TCP] FRTO: Delay skb available check until it's mandatory
[XFRM]: Restrict upper layer information by bundle.
[TCP]: Catch skb with S+L bugs earlier
[PATCH] INET : IPV4 UDP lookups converted to a 2 pass algo
[L2TP]: Add the ability to autoload a pppox protocol module.
[SKB]: Introduce skb_queue_walk_safe()
[AF_IUCV/IUCV]: smp_call_function deadlock
[IPV6]: Fix slab corruption running ip6sic
[TCP]: Update references in two old comments
[XFRM]: Export SPD info
[IPV6]: Track device renames in snmp6.
[SCTP]: Fix sctp_getsockopt_local_addrs_old() to use local storage.
[NET]: Remove NETIF_F_INTERNAL_STATS, default to internal stats.
[NETPOLL]: Remove CONFIG_NETPOLL_RX
...
* 'for-linus' of git://git.kernel.dk/data/git/linux-2.6-block:
[PATCH] elevator: elv_list_lock does not need irq disabling
[BLOCK] Don't pin lots of memory in mempools
cfq-iosched: speedup cic rb lookup
ll_rw_blk: add io_context private pointer
cfq-iosched: get rid of cfqq hash
cfq-iosched: tighten queue request overlap condition
cfq-iosched: improve sync vs async workloads
cfq-iosched: never allow an async queue idling
cfq-iosched: get rid of ->dispatch_slice
cfq-iosched: don't pass unused preemption variable around
cfq-iosched: get rid of ->cur_rr and ->cfq_list
cfq-iosched: slice offset should take ioprio into account
[PATCH] cfq-iosched: style cleanups and comments
cfq-iosched: sort IDLE queues into the rbtree
cfq-iosched: sort RT queues into the rbtree
[PATCH] cfq-iosched: speed up rbtree handling
cfq-iosched: rework the whole round-robin list concept
cfq-iosched: minor updates
cfq-iosched: development update
cfq-iosched: improve preemption for cooperating tasks
The updated IP-MIB RFC (RFC4293) specifys new objects, InBcastPkts
and OutBcastPkts. This adds definitions for them.
Signed-off-by: Mitsuru Chinen <mitch@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a corner case where less than MSS sized new data thingie
is awaiting in the send queue. For F-RTO to work correctly, a
new data segment must be sent at certain point or F-RTO cannot
be used at all. RFC4138 allows overriding of Nagle at that
point.
Implementation uses frto_counter states 2 and 3 to distinguish
when Nagle override is needed.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
On MIPv6 usage, XFRM sub policy is enabled.
When main (IPsec) and sub (MIPv6) policy selectors have the same
address set but different upper layer information (i.e. protocol
number and its ports or type/code), multiple bundle should be created.
However, currently we have issue to use the same bundle created for
the first time with all flows covered by the case.
It is useful for the bundle to have the upper layer information
to be restructured correctly if it does not match with the flow.
1. Bundle was created by two policies
Selector from another policy is added to xfrm_dst.
If the flow does not match the selector, it goes to slow path to
restructure new bundle by single policy.
2. Bundle was created by one policy
Flow cache is added to xfrm_dst as originated one. If the flow does
not match the cache, it goes to slow path to try searching another
policy.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
SACKED_ACKED and LOST are mutually exclusive with SACK, thus
having their sum larger than packets_out is bug with SACK.
Eventually these bugs trigger traps in the tcp_clean_rtx_queue
with SACK but it's much more informative to do this here.
Non-SACK TCP, however, could get more than packets_out duplicate
ACKs which each increment sacked_out, so it makes sense to do
this kind of limitting for non-SACK TCP but not for SACK enabled
one. Perhaps the author had the opposite in mind but did the
logic accidently wrong way around? Anyway, the sacked_out
incrementer code for non-SACK already deals this issue before
calling sync_left_out so this trapping can be done
unconditionally.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we scale the mempool sizes depending on memory installed
in the machine, except for the bio pool itself which sits at a fixed
256 entry pre-allocation.
There's really no point in "optimizing" this OOM path, we just need
enough preallocated to make progress. A single unit is enough, lets
scale it down to 2 just to be on the safe side.
This patch saves ~150kb of pinned kernel memory on a 32-bit box.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch provides a method for walking skb lists while inserting or
removing skbs from the list.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch puts enable_kernel_spe into <asm-powerpc/system.h> along with
enable_kernel_altivec etc.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The arch/ppc/syslib/ppc_sys.c infrastructure does not work well for the
virtex ports. Move the ml300 and ml403 board ports over to use the new
virtex_devices infrastructure.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The header files for the ml403 and ml300 are virtually identical, merge
them into a single file.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (107 commits)
smc911x: fix compilation breakage wjen debug is on
[netdrvr] eexpress: minor corrections
add NAPI support to sb1250-mac.c
ixgb: ROUND_UP macro cleanup in drivers/net/ixgb
e1000: ROUND_UP macro cleanup in drivers/net/e1000
Generic HDLC sparse annotations
e100: Optionally use I/O mode only to access register space
e100: allow bad MAC address when running with invalid eeprom csum
ehea: fix for dlpar support
ehea: fix for sysfs entries
3C509: Remove unnecessary include of <linux/pm_legacy.h>
NetXen: Fix for vmalloc issues
NetXen: Fixes for Power PC architecture
NetXen: Port swap feature for multi port cards
NetXen: Removal of redundant macros
NetXen: Multi PCI support for Quad cards
NetXen: Removal of redundant argument passing
NetXen: Use multiple PCI functions
[netdrvr e100] experiment with doing RX in a similar manner to eepro100
[PATCH] ieee80211: add missing global needed by IEEE80211_DEBUG_XXXX
...
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: (86 commits)
SPIN_LOCK_UNLOCKED cleanup in drivers/ata/pata_winbond.c
drivers/ata/pata_cmd640.c: fix build with CONFIG_PM=n
pata_hpt37x: Further small fixes
pata_hpt3x2n: Add HPT371N support and other bits
ata: printk warning fixes
libata: separate ATA_EHI_DID_RESET into DID_SOFTRESET and DID_HARDRESET
ahci: consolidate common port flags
ata_timing: ensure t->cycle is always correct
libata: add missing call to ->cable_detect() in new EH path
pata_amd: remove contamination added during cable_detect conversion
libata: Handle drives that require a spin-up command before first access
libata: HPA support
libata: kill probe_ent and related helpers
libata: convert the remaining PATA drivers to new init model
libata: convert the remaining SATA drivers to new init model
libata: convert ata_pci_init_native_mode() users to new init model
libata: convert drivers with combined SATA/PATA ports to new init model
libata: add init helpers including ata_pci_prepare_native_host()
libata: convert native PCI host handling to new init model
libata: convert legacy PCI host handling to new init model
...
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (105 commits)
sonypi: use mutex instead of semaphore
sony-laptop: remove user visible camera controls as platform attributes
meye: make meye use sony-laptop instead of sonypi
sony-laptop: add a meye-usable include file for camera ops
sony-laptop: complete the motion eye camera support in sony-laptop
sonypi: try to detect if sony-laptop has already taken one of the known ioports
sonypi: suggest sonypi users to try sony-laptop instead
sony-laptop: add edge modem support (also called WWAN)
sony-laptop: add locking on accesses to the ioport and global vars
sony-laptop: add camera enable/disable parameter, better handle possible infinite loop
thinkpad-acpi: make drivers/misc/thinkpad_acpi:fan_mutex static
ACPI: thinkpad-acpi: add sysfs support to wan and bluetooth subdrivers
ACPI: thinkpad-acpi: add sysfs support to hotkey subdriver
ACPI: thinkpad-acpi: improve dock subdriver initialization
ACPI: thinkpad-acpi: improve debugging for acpi helpers
ACPI: thinkpad-acpi: improve fan control documentation
ACPI: thinkpad-acpi: map ENXIO to EINVAL for fan sysfs
ACPI: thinkpad-acpi: fix a fan watchdog invocation
ACPI: thinkpad-acpi: do not arm fan watchdog if it would not work
ACPI: thinkpad-acpi: add a fan-control feature master toggle
...
Calling smp_call_function can lead to a deadlock if it is called
from tasklet context.
Fixing this deadlock requires to move the smp_call_function from the
tasklet context to a work queue. To do that queue the path pending
interrupts to a separate list and move the path cleanup out of
iucv_path_sever to iucv_path_connect and iucv_path_pending.
This creates a new requirement for iucv_path_connect: it may not be
called from tasklet context anymore.
Also fixed compile problem for CONFIG_HOTPLUG_CPU=n and
another one when walking the cpu_online mask. When doing this,
we must disable cpu hotplug.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch you can use iproute2 in user space to efficiently see
how many policies exist in different directions.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu conviced me that a new flag was overkill; every driver
currently overrides get_stats, so we might as well make the internal
one the default. If someone did fail to set get_stats, they would now
get all 0 stats instead of "No statistics available".
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_NETPOLL_TRAP causes the TX queue controls to be completely bypassed in
the netpoll's "trapped" mode which easily causes overflows in the drivers with
short TX queues (most notably, in 8139too with its 4-deep queue). So, make
this option more sensible by making it only bypass the TX softirq wakeup.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Acked-by: Tom Rini <trini@kernel.crashing.org>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Copy and rename (for easier co-existence) the MEYE-wise exported interface.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
Separate ATA_EHI_DID_RESET into ATA_EHI_DID_SOFTRESET and
ATA_EHI_DID_HARDRESET. ATA_EHI_DID_RESET is redefined as OR of the
two flags. This patch doesn't introduce any behavior change. This
will be used later to determine whether _SDD is necessary or not.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
(S)ATA drives can be configured for "power-up in standby",
a mode whereby a specific "spin up now!" command is required
before the first media access.
Currently, a drive with this feature enabled can not be used at all
with libata, and once in this mode, the drive becomes a doorstop.
The older drivers/ide subsystem at least enumerates the drive,
so that it can be woken up after the fact from a userspace HDIO_*
command, but not libata.
This patch adds support to libata for the "power-up in standby"
mode where a "spin up now!" command (SET_FEATURES) is needed.
With this, libata will recognize such drives, spin them up,
and then re-IDENTIFY them if necessary to get a full/complete
set of drive features data.
Drives in this state are determined by looking for
special values in id[2], as documented in the current ATA specs.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Add support for ignoring the BIOS HPA result (off by default) and setting
the disk to the full available size unless already frozen.
Tested with various platforms/disks and confirmed to work with the
Macintosh (which broke earlier) and ata_piix (breakage due to the LBA48
readback that Tejun fixed).
For normal users this brings us, I believe, to feature parity with old IDE
(and of course more featured in some areas too).
Signed-off-by: Jeff Garzik <jeff@garzik.org>
All drivers are converted to new init model. Kill probe_ent,
ata_device_add() and ata_pci_init_native_mode().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
These will be used to convert LLDs to new init model.
* Add irq_handler field to port_info. In new init model, requesting
IRQ is LLD's responsibility and libata doesn't need to know about
irq_handler. Most LLDs can simply register their irq_handler but
some need different irq_handler depending on specific chip. The
added port_info->irq_handler field can be used by LLDs to select
the matching IRQ handler in such cases.
* Add ata_dummy_port_info.
* Implement ata_pci_prepare_native_host(), a helper to alloc ATA host,
acquire all resources and init the host in one go.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert native PCI host handling to alloc-init-register model. New
function ata_pci_init_native_host() follows the new init model and
replaces ata_pci_init_native_mode(). As there are remaining LLD
users, the old function isn't removed yet.
ata_pci_init_one() is reimplemented using the new function and now
fully converted to new init model.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ata_host_alloc_pinfo() and ata_host_register(). These helpers
will be used in the following patches to adopt new init model.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reorganize ata_host_alloc() and its subroutines into the following
three functions.
* ata_host_alloc() : allocates host and its ports. shost is not
registered automatically.
* ata_scsi_add_hosts() : allocates and adds shosts associated with an
ATA host. Used by ata_host_register().
* ata_host_register() : takes a fully initialized ata_host structure
and registers it to libata layer and probes it.
Only ata_host_alloc() and ata_host_register() are exported.
ata_device_add() is rewritten using the above functions. This patch
does not introduce any observable behavior change. Things worth
mentioning.
* print_id is assigned at registration time and LLDs are allowed to
overallocate ports and reduce host->n_ports during initialization.
ata_host_register() will throw away unused ports automatically.
* All SCSI host initialization stuff now resides in
ata_scsi_add_hosts() in libata-scsi.c, where it should be.
* ipr is now the only user of ata_host_init(). Either kill it by
converting ipr to use ata_host_alloc() and friends or rename and
move it to libata-scsi.c
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out ata_host_start() from ata_device_add(). ata_host_start()
calls ->port_start on each port if available and freezes the port.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Geoff Levand
Johannes Berg
David Gibson
Christian Krafft
Mathieu Desnoyers
Benjamin Herrenschmidt
David Rientjes
Jeremy Fitzhardinge
Robert Peterson
Linus Torvalds
Mitsuru Chinen
Ilpo Järvinen
Masahide NAKAMURA
Jens Axboe
Jens Axboe
James Chapman
Paul Mackerras
Grant Likely
Martin Schwidefsky
Jamal Hadi Salim
Rusty Russell
Sergei Shtylyov
Len Brown
malattia@linux.it
Tejun Heo
Mark Lord
Alan Cox