After thinking it over a lot it made more sense for the core to deal with
the output polling especially so it can notify X.
v2: drop plans for fake connector - per Michel's comments - fix X patch sent to xorg-devel, add intel polled/hpd setting, add initial nouveau polled/hpd settings.
v3: add config lock take inside polling, add intel/nouveau poll init/fini calls
v4: config lock was a bit agressive, only needed around connector list reading.
otherwise it could re-enter.
glisse: discard drm_helper_hpd_irq_event
v3: Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This breaks the connection between the core drm connector list
and the fbdev connector usage, and allows them to become disjoint
in the future. It also removes the untype void* that was in the
connector struct to support this.
All connectors are added to the fbdev now but this could be
changed in the future.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The fbdev layer in the kms code should act like a consumer of the kms services and avoid having relying on information being store in the kms core structures in order for it to work.
This patch
a) removes the info pointer/psuedo palette from the core drm_framebuffer structure and moves it to the fbdev helper layer, it also removes the core drm keeping a list of kernel kms fbdevs.
b) migrated all the fb helper functions out of the crtc helper file into the fb helper file.
c) pushed the fb probing/hotplug control into the driver
d) makes the surface sizes into a structure for ease of passing
This changes the intel/radeon/nouveau drivers to use the new helper.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds support for the setcmap api and fixes the 8bpp
support at least on radeon hardware. It adds a new load_lut
hook which can be called once the color map is setup.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This initialises the fb helper with the connector helper,
so that the fb cmdline code works for intel as well.
Signed-off-by: Dave Airlie <airlied@redhat.com>
For shared tv-out and VGA encoders, we really need to know if
the encoder is just being switched off temporarily in blanking
or if we are really disabling it hard.
Also we need to try harder to disconnect encoders from unused
connectors so we can share more efficently.
(shared encoders stuff is coming in radeon tv-out support)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Making the drm_crtc.c code recognize the DPMS property and invoke the
connector->dpms function doesn't remove any capability from the driver while
reducing code duplication.
That just highlighted the problem with the existing DPMS functions which
could turn off the connector, but failed to turn off any relevant crtcs. The
new drm_helper_connector_dpms function manages all of that, using the
drm_helper-specific crtc and encoder dpms functions, automatically computing
the appropriate DPMS level for each object in the system.
This fixes the current troubles in the i915 driver which left PLLs, pipes
and planes running while in DPMS_OFF mode or even while they were unused.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Remove an include that isn't actually needed to prevent needless
rebuilds.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In some cases we may receive a mode config that has a different
CRTC<->encoder map that the current configuration. In that case, we
need to disable any re-routed encoders before setting the mode,
otherwise they may not pick up the new CRTC (if the output types are
incompatible for example).
Tested-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Check the error paths within intel_pipe_set_base() to first cleanup and
then report back the error.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
When mode setting is first initialized, the driver will call into
drm_helper_initial_config() to set up an initial output and framebuffer
configuration. This routine is responsible for probing the available
connectors, encoders, and crtcs, looking for modes and putting together
something reasonable (where reasonable is defined as "allows kernel
messages to be visible on as many displays as possible").
However, the code was a bit too aggressive in setting default modes when
none were found on a given connector. Even if some connectors had modes,
any connectors found lacking modes would have the default 800x600 mode added
to their mode list, which in some cases could cause problems later down the
line. In my case, the LVDS was perfectly available, but the initial config
code added 800x600 modes to both of the detected but unavailable HDMI
connectors (which are on my non-existent docking station). This ended up
preventing later code from setting a mode on my LVDS, which is bad.
This patch fixes that behavior by making the initial config code walk
through the connectors first, counting the available modes, before it decides
to add any default modes to a possibly connected output. It also fixes the
logic in drm_target_preferred() that was causing zeroed out modes to be set
as the preferred mode for a given connector, even if no modes were available.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This removes the requirement for user space to pin a buffer before
setting a mode that is backed by the pixels from that buffer.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Add mode setting support to the DRM layer.
This is a fairly big chunk of work that allows DRM drivers to provide
full output control and configuration capabilities to userspace. It was
motivated by several factors:
- the fb layer's APIs aren't suited for anything but simple
configurations
- coordination between the fb layer, DRM layer, and various userspace
drivers is poor to non-existent (radeonfb excepted)
- user level mode setting drivers makes displaying panic & oops
messages more difficult
- suspend/resume of graphics state is possible in many more
configurations with kernel level support
This commit just adds the core DRM part of the mode setting APIs.
Driver specific commits using these new structure and APIs will follow.
Co-authors: Jesse Barnes <jbarnes@virtuousgeek.org>, Jakob Bornecrantz <jakob@tungstengraphics.com>
Contributors: Alan Hourihane <alanh@tungstengraphics.com>, Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie
Dave Airlie
Maarten Maathuis
Keith Packard
Jesse Barnes
Jean Delvare
Chris Wilson
Kristian Høgsberg