Extension IEs have ID 255 followed by extension ID. Current
code is buggy in handling it in two ways:
1. When checking if IE is in the frame, it uses just the ID, which
for extension elements is too broad.
2. It uses 0xFF to mark copied IEs, which will result in not copying
extension IEs from the subelement.
Fix both issue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the new IEs are generated, the multiple BSSID elements
are not saved. Save aside properties that are needed later
for PS.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Parsing and exposing nontransmitted APs is problematic
when underlying HW doesn't support it. Do it only if
driver indicated support. Allow HE restriction as well,
since the HE spec defined the exact manner that Multiple
BSSID set should behave. APs that not support the HE
spec will have less predictable Multiple BSSID set
support/behavior
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously the transmitted BSS and the non-trasmitted BSS list were
defined in struct cfg80211_internal_bss. Move them to struct cfg80211_bss
since mac80211 needs this info.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When holding data of the non-transmitting BSS, we need to keep the
transmitting BSS data on. Otherwise it will be released, and release
the non-transmitting BSS with it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the new for_each_element() helper here, we cannot use
for_each_subelement() since we have a fixed 1 byte before
the subelements start.
While at it, also fix le16_to_cpup() to be get_unaligned_le16()
since we don't know anything about alignment.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This extends cfg80211 BSS table processing to be able to parse Multiple
BSSID element from Beacon and Probe Response frames and to update the
BSS profiles in internal database for non-transmitted BSSs.
Signed-off-by: Peng Xu <pxu@codeaurora.org>
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This makes for much simpler code, simply walk through all
the elements and check that the last one found ends with
the end of the data. This works because if any element is
malformed the walk is aborted, we end up with a mismatch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We currently have a number of helpers to find elements that just
return a u8 *, change those to return a struct element and add
inlines to deal with the u8 * compatibility.
Note that the match behaviour is changed to start the natch at
the data, so conversion from _ie_match to _elem_match need to
be done carefully.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rather than always iterating elements from frames with pure
u8 pointers, add a type "struct element" that encapsulates
the id/datalen/data format of them.
Then, add the element iteration macros
* for_each_element
* for_each_element_id
* for_each_element_extid
which take, as their first 'argument', such a structure and
iterate through a given u8 array interpreting it as elements.
While at it and since we'll need it, also add
* for_each_subelement
* for_each_subelement_id
* for_each_subelement_extid
which instead of taking data/length just take an outer element
and use its data/datalen.
Also add for_each_element_completed() to determine if any of
the loops above completed, i.e. it was able to parse all of
the elements successfully and no data remained.
Use for_each_element_id() in cfg80211_find_ie_match() as the
first user of this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we destroy the interface we already hold the wdev->mtx
while calling cfg80211_pmsr_wdev_down(), which assumes this
isn't true and flushes the worker that takes the lock, thus
leading to a deadlock.
Fix this by refactoring the worker and calling its code in
cfg80211_pmsr_wdev_down() directly.
We still need to flush the work later to make sure it's not
still running and will crash, but it will not do anything.
Fixes: 9bb7e0f24e ("cfg80211: add peer measurement with FTM initiator API")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we *don't* have a MAC address attribute, we shouldn't
try to use this - this was intended to copy the local MAC
address instead, so fix it.
Fixes: 9bb7e0f24e ("cfg80211: add peer measurement with FTM initiator API")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we now prevent regulatory restore during STA disconnect
if concurrent AP interfaces are active, we need to reschedule
this check when the AP state changes. This fixes never doing
a restore when an AP is the last interface to stop. Or to put
it another way: we need to re-check after anything we check
here changes.
Cc: stable@vger.kernel.org
Fixes: 113f3aaa81 ("cfg80211: Prevent regulatory restore during STA disconnect in concurrent interfaces")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In typical cases, there's no need to pass both the maxattr
and the policy array pointer, as the maxattr should just be
ARRAY_SIZE(policy) - 1. Therefore, to be less error prone,
just remove the maxattr argument from the default macros
and deduce the size accordingly.
Leave the original macros with a leading underscore to use
here and in case somebody needs to pass a policy pointer
where the policy isn't declared in the same place and thus
ARRAY_SIZE() cannot be used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge net-next so that we get the changes from net, which would
otherwise conflict with the NLA_POLICY_NESTED/_ARRAY changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Host drivers may offload authentication to the user space
through the commit ("cfg80211: Authentication offload to
user space in AP mode").
This interface can be used to implement SAE by having the
userspace do authentication/PMKID key derivation and driver
handle the association.
A step ahead, this interface can get further optimized if the
PMKID is passed to the host driver and also have it respond to
the association request by the STA on a valid PMKID.
This commit enables the userspace to pass the PMKID to the host
drivers through the set/del pmksa operations in AP mode.
Set/Del pmksa is now restricted to STA/P2P client mode only and
thus the drivers might not expect them in any other(AP) mode.
This commit also introduces a feature flag
NL80211_EXT_FEATURE_AP_PMKSA_CACHING (johannes: renamed) to
maintain the backward compatibility of such an expectation by
the host drivers. These operations are allowed in AP mode only
when the drivers advertize the capability through this flag.
Signed-off-by: Liangwei Dong <liangwei@codeaurora.org>
Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
[rename flag to NL80211_EXT_FEATURE_AP_PMKSA_CACHING]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
commit 40cbfa9021 ("cfg80211/nl80211: Optional authentication
offload to userspace")' introduced authentication offload to user
space by the host drivers in station mode. This commit extends
the same for the AP mode too.
Extend NL80211_ATTR_EXTERNAL_AUTH_SUPPORT to also claim the
support of external authentication from the user space in AP mode.
A new flag parameter is introduced in cfg80211_ap_settings to
intend the same while "start ap".
Host driver to use NL80211_CMD_FRAME interface to transmit and
receive the authentication frames to / from the user space.
Host driver to indicate the flag NL80211_RXMGMT_FLAG_EXTERNAL_AUTH
while sending the authentication frame to the user space. This
intends to the user space that the driver wishes it to process
the authentication frame for certain protocols, though it had
initially advertised the support for SME functionality.
User space shall accordingly do the authentication and indicate
its final status through the command NL80211_CMD_EXTERNAL_AUTH.
Allow the command even if userspace doesn't include the attribute
NL80211_ATTR_SSID for AP interface.
Host driver shall continue with the association sequence and
indicate the STA connection status through cfg80211_new_sta.
To facilitate the host drivers in AP mode for matching the pmkid
by the stations during the association, NL80211_CMD_EXTERNAL_AUTH
is also enhanced to include the pmkid to drivers after
the authentication.
This pmkid can also be used in the STA mode to include in the
association request.
Also modify nl80211_external_auth to not mandate SSID in AP mode.
Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
[remove useless nla_get_flag() usage]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There was no such capability advertisement from the driver and thus the
current user space has to assume the driver to support all the AKMs. While
that may be the case with some drivers (e.g., mac80211-based ones), there
are cfg80211-based drivers that implement SME and have constraints on
which AKMs can be supported (e.g., such drivers may need an update to
support SAE AKM using NL80211_CMD_EXTERNAL_AUTH). Allow such drivers to
advertise the exact set of supported AKMs so that user space tools can
determine what network profile options should be allowed to be configured.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
[pmsr data might be big, start a new netlink message section]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently Self Managed WIPHY's are not notified on any
hints other than user cell base station hints.
Self Managed wiphy's basically rely on hints from firmware
and its local regdb for regulatory management, so hints from wireless
core can be ignored. But all user hints needs to be notified
to them to provide flexibility to these drivers to honour or
ignore these user hints.
Currently none of the drivers supporting self managed wiphy
register a notifier with cfg80211. Hence this change does not affect
any other driver behavior.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warnings:
net/wireless/wext-compat.c:1327:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
net/wireless/wext-compat.c:1341:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Recently, DMG frequency bands have been extended till 71GHz, so extend
the range check till 20GHz (45-71GHZ), else some channels will be marked
as disabled.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@bluwireless.co.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there are simulatenous queries of regdb, then there might be a case
where multiple queries can trigger request_firmware_no_wait and can have
parallel callbacks being executed asynchronously. In this scenario we
might hit the WARN_ON.
So remove the warn_on, as the code already handles multiple callbacks
gracefully.
Signed-off-by: Chaitanya Tata <chaitanya.tata@bluwireless.co.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
syzbot reported an out-of-bounds read when passing certain
malformed messages into nl80211. The specific place where
this happened isn't interesting, the problem is that nested
policy parsing was referring to the wrong maximum attribute
and thus the policy wasn't long enough.
Fix this by referring to the correct attribute. Since this
is really not necessary, I'll come up with a separate patch
to just pass the policy instead of both, in the common case
we can infer the maxattr from the size of the policy array.
Reported-by: syzbot+4157b036c5f4713b1f2f@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Fixes: 9bb7e0f24e ("cfg80211: add peer measurement with FTM initiator API")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Expose path change count to destination in mpath info
Signed-off-by: Julan Hsu <julanhsu@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Expose hop count to destination information in mpath info
Signed-off-by: Julan Hsu <julanhsu@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds TX airtime statistics to the cfg80211 station dump (to go along
with the RX info already present), and adds a new parameter to set the
airtime weight of each station. The latter allows userspace to implement
policies for different stations by varying their weights.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
[rmanohar@codeaurora.org: fixed checkpatch warnings]
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
[move airtime weight != 0 check into policy]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull crypto updates from Herbert Xu:
"API:
- Add 1472-byte test to tcrypt for IPsec
- Reintroduced crypto stats interface with numerous changes
- Support incremental algorithm dumps
Algorithms:
- Add xchacha12/20
- Add nhpoly1305
- Add adiantum
- Add streebog hash
- Mark cts(cbc(aes)) as FIPS allowed
Drivers:
- Improve performance of arm64/chacha20
- Improve performance of x86/chacha20
- Add NEON-accelerated nhpoly1305
- Add SSE2 accelerated nhpoly1305
- Add AVX2 accelerated nhpoly1305
- Add support for 192/256-bit keys in gcmaes AVX
- Add SG support in gcmaes AVX
- ESN for inline IPsec tx in chcr
- Add support for CryptoCell 703 in ccree
- Add support for CryptoCell 713 in ccree
- Add SM4 support in ccree
- Add SM3 support in ccree
- Add support for chacha20 in caam/qi2
- Add support for chacha20 + poly1305 in caam/jr
- Add support for chacha20 + poly1305 in caam/qi2
- Add AEAD cipher support in cavium/nitrox"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (130 commits)
crypto: skcipher - remove remnants of internal IV generators
crypto: cavium/nitrox - Fix build with !CONFIG_DEBUG_FS
crypto: salsa20-generic - don't unnecessarily use atomic walk
crypto: skcipher - add might_sleep() to skcipher_walk_virt()
crypto: x86/chacha - avoid sleeping under kernel_fpu_begin()
crypto: cavium/nitrox - Added AEAD cipher support
crypto: mxc-scc - fix build warnings on ARM64
crypto: api - document missing stats member
crypto: user - remove unused dump functions
crypto: chelsio - Fix wrong error counter increments
crypto: chelsio - Reset counters on cxgb4 Detach
crypto: chelsio - Handle PCI shutdown event
crypto: chelsio - cleanup:send addr as value in function argument
crypto: chelsio - Use same value for both channel in single WR
crypto: chelsio - Swap location of AAD and IV sent in WR
crypto: chelsio - remove set but not used variable 'kctx_len'
crypto: ux500 - Use proper enum in hash_set_dma_transfer
crypto: ux500 - Use proper enum in cryp_set_dma_transfer
crypto: aesni - Add scatter/gather avx stubs, and use them in C
crypto: aesni - Introduce partial block macro
..
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
* virt_wifi - wireless control simulation on top of
another network interface
* hwsim configurability to test capabilities similar
to real hardware
* various mesh improvements
* various radiotap vendor data fixes in mac80211
* finally the nl_set_extack_cookie_u64() we talked
about previously, used for
* peer measurement APIs, right now only with FTM
(flight time measurement) for location
* made nl80211 radio/interface announcements more complete
* various new HE (802.11ax) things:
updates, TWT support, ...
-----BEGIN PGP SIGNATURE-----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=EpyK
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-12-19' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have too many changes to list, highlights:
* virt_wifi - wireless control simulation on top of
another network interface
* hwsim configurability to test capabilities similar
to real hardware
* various mesh improvements
* various radiotap vendor data fixes in mac80211
* finally the nl_set_extack_cookie_u64() we talked
about previously, used for
* peer measurement APIs, right now only with FTM
(flight time measurement) for location
* made nl80211 radio/interface announcements more complete
* various new HE (802.11ax) things:
updates, TWT support, ...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix two bugs in ieee80211_get_vht_max_nss():
* the spec says we should round down
(reported by Nissim)
* there's a double condition, the first one is wrong,
supp_width == 0 / ext_nss_bw == 2 is valid in 80+80
(found by smatch)
Fixes: b0aa75f0b1 ("ieee80211: add new VHT capability fields/parsing")
Reported-by: Nissim Bendanan <nissimx.bendanan@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If validate_pae_over_nl80211() were to fail in nl80211_crypto_settings(),
we might leak the 'connkeys' allocation. Fix this.
Fixes: 64bf3d4bc2 ("nl80211: Add CONTROL_PORT_OVER_NL80211 attribute")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently radar detection and corresponding channel switch is handled
at the AP device. STA ignores these detected radar events since the
radar signal can be seen mostly by the AP as well. But in scenarios where
a radar signal is seen only at STA, notifying this event to the AP which
can trigger a channel switch can be useful.
Stations can report such radar events autonomously through Spectrum
management (Measurement Report) action frame to its AP. The userspace on
processing the report can notify the kernel with the use of the added
NL80211_CMD_NOTIFY_RADAR to indicate the detected event and inturn adding
the reported channel to NOL.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are talks about enabling -Wimplicit-fallthrough warnings in the
mainline and it is already enabled in linux-next. Add all the
missing annotations to prevent warnings when this happens.
And in one case, remove the extra text from the annotation so that the
compiler recognizes it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function was modified to support the information element extension
case (WLAN_EID_EXTENSION) in a manner that would result in an infinite
loop when going through set of IEs that include WLAN_EID_RIC_DATA and
contain an IE that is in the after_ric array. The only place where this
can currently happen is in mac80211 ieee80211_send_assoc() where
ieee80211_ie_split_ric() is called with after_ric[].
This can be triggered by valid data from user space nl80211
association/connect request (i.e., requiring GENL_UNS_ADMIN_PERM). The
only known application having an option to include WLAN_EID_RIC_DATA in
these requests is wpa_supplicant and it had a bug that prevented this
specific contents from being used (and because of that, not triggering
this kernel bug in an automated test case ap_ft_ric) and now that this
bug is fixed, it has a workaround to avoid this kernel issue.
WLAN_EID_RIC_DATA is currently used only for testing purposes, so this
does not cause significant harm for production use cases.
Fixes: 2512b1b18d ("mac80211: extend ieee80211_ie_split to support EXTENSION")
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
'cipher' algorithms (single block ciphers) are always synchronous, so
passing CRYPTO_ALG_ASYNC in the mask to crypto_alloc_cipher() has no
effect. Many users therefore already don't pass it, but some still do.
This inconsistency can cause confusion, especially since the way the
'mask' argument works is somewhat counterintuitive.
Thus, just remove the unneeded CRYPTO_ALG_ASYNC flags.
This patch shouldn't change any actual behavior.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When peering is in userspace, some implementations may want to control
which peers are accepted based on RSSI in addition to the information
elements being sent today. Add signal level so that info is available
to clients.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When userspace is controlling mesh routing, it may have better
knowledge about whether a mesh STA is connected to a mesh
gate than the kernel mpath table. Add dot11MeshConnectedToMeshGate
to the mesh config so that such applications can explicitly
signal that a mesh STA is connected to a gate, which will then
be advertised in the beacon.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Capture the current state of gate connectivity from the mesh
formation field in mesh config whenever we receive a beacon,
and report that via GET_STATION. This allows applications
doing mesh peering in userspace to make peering decisions
based on peers' current upstream connectivity.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Let userspace learn about iftype changes by sending a notification
when handling the NL80211_CMD_SET_INTERFACE command. There seems
to be no other place where the iftype can change: nl80211_set_interface
is the only caller of cfg80211_change_iface which is the only caller of
ops->change_virtual_intf.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a wiphy changes its namespace, all interfaces are moved to the
new namespace as well. The network interfaces are properly announced
as leaving on the old and as appearing on the new namespace through
RTM_NEWLINK/RTM_DELLINK. On nl80211, however, these events are missing
for radios and their interfaces.
Add netlink announcements through nl80211 when switching namespaces,
so userspace can rely on these events to discover radios properly.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new "peer measurement" API, that can be used to measure
certain things related to a peer. Right now, only implement
FTM (flight time measurement) over it, but the idea is that
it'll be extensible to also support measuring the necessary
things to calculate e.g. angle-of-arrival for WiGig.
The API is structured to have a generic list of peers and
channels to measure with/on, and then for each of those a
set of measurements (again, only FTM right now) to perform.
Results are sent to the requesting socket, including a final
complete message.
Closing the controlling netlink socket will abort a running
measurement.
v3:
- add a bit to report "final" for partial results
- remove list keeping etc. and just unicast out the results
to the requester (big code reduction ...)
- also send complete message unicast, and as a result
remove the multicast group
- separate out struct cfg80211_pmsr_ftm_request_peer
from struct cfg80211_pmsr_request_peer
- document timeout == 0 if no timeout
- disallow setting timeout nl80211 attribute to 0,
must not include attribute for no timeout
- make MAC address randomization optional
- change num bursts exponent default to 0 (1 burst, rather
rather than the old default of 15==don't care)
v4:
- clarify NL80211_ATTR_TIMEOUT documentation
v5:
- remove unnecessary nl80211 multicast/family changes
- remove partial results bit/flag, final is sufficient
- add max_bursts_exponent, max_ftms_per_burst to capability
- rename "frames per burst" -> "FTMs per burst"
v6:
- rename cfg80211_pmsr_free_wdev() to cfg80211_pmsr_wdev_down()
and call it in leave, so the device can't go down with any
pending measurements
v7:
- wording fixes (Lior)
- fix ftm.max_bursts_exponent to allow having the limit of 0 (Lior)
v8:
- copyright statements
- minor coding style fixes
- fix error path leak
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This variable shadows something that gets generated inside
the tracing macros, which causes sparse to warn. Avoid it
so sparse output is more readable, even if it doesn't seem
to cause any trouble.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently when an AP and STA interfaces are active in the same or different
radios, regulatory settings are restored whenever the STA disconnects. This
restores all channel information including dfs states in all radios.
For example, if an AP interface is active in one radio and STA in another,
when radar is detected on the AP interface, the dfs state of the channel
will be changed to UNAVAILABLE. But when the STA interface disconnects,
this issues a regulatory disconnect hint which restores all regulatory
settings in all the radios attached and thereby losing the stored dfs
state on the other radio where the channel was marked as unavailable
earlier. Hence prevent such regulatory restore whenever another active
beaconing interface is present in the same or other radios.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When FTM is enabled, doing a CSA will unexpectedly lose it since
the value of ftm_responder may be initialized to 0 instead of -1,
so fix that.
Fixes: 81e54d08d9 ("cfg80211: support FTM responder configuration/statistics")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do a logical vht_capa &= vht_capa_mask of user-supplied VHT mask with
the driver-supplied mask of modifiable VHT capabilities.
Fix whitespaces and comment typos.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for drivers to report the total number of MPDUs received
and the number of MPDUs received with an FCS error from a specific
peer. These counters will be incremented only when the TA of the
frame matches the MAC address of the peer irrespective of FCS
error.
It should be noted that the TA field in the frame might be corrupted
when there is an FCS error and TA matching logic would fail in such
cases. Hence, FCS error counter might not be fully accurate, but it can
provide help in detecting bad RX links in significant number of cases.
This FCS error counter without full accuracy can be used, e.g., to
trigger a kick-out of a connected client with a bad link in AP mode to
force such a client to roam to another AP.
Signed-off-by: Ankita Bajaj <bankita@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of open-coding a lot of calls to is_valid_ie_attr(),
add this validation directly to the policy, now that we can.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Many range checks can be done in the policy, move them
there. A few in mesh are added in the code (taken out of
the macros) because they don't fit into the s16 range in
the policy validation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using skcipher just makes the code longer, and mac80211
also "open-codes" the WEP encrypt/decrypt.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge net-next, which pulled in net, so I can merge a few more
patches that would otherwise conflict.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
There were supposed to be two blocks - one for each direction
cfg80211 <-> driver, clean up the code to restore that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There isn't really any need for us to be sending this from
two different places - move cfg80211_init_wdev() later and
send the notification from there, removing it from the non-
netdev case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We currently have two places that do similar things, depending
on whether it's a wdev with or without netdev.
Combine the code to avoid having to duplicate all new additions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add some error messages to nl80211_parse_chandef() to make
failures here - especially with disabled channels - easier
to diagnose.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no reason for drivers to be able to access the
cfg80211 internal cookie counter; move it out of the
wiphy into the rdev structure.
While at it, also make it never assign 0 as a cookie
(we consider that invalid in some places), and warn if
we manage to do that for some reason (wrapping is not
likely to happen with a u64.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since my change to split out the regulatory init to occur later,
any issues during earlier cfg80211_init() or errors during the
platform device allocation would lead to crashes later. Make this
more robust by checking that the earlier initialization succeeded.
Fixes: d7be102f29 ("cfg80211: initialize regulatory keys/database later")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
nl80211_prepare_wdev_dump() is using the output skb to look up
the network namespace, but this isn't really necessary, it can
just as well use the input skb which is available as cb->skb,
the sk is the same anyway.
Therefore, remove the redundant argument.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow userspace to enable fine timing measurement responder
functionality with configurable lci/civic parameters in AP mode.
This can be done at AP start or changing beacon parameters.
A new EXT_FEATURE flag is introduced for drivers to advertise
the capability.
Also nl80211 API support for retrieving statistics is added.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
[remove unused cfg80211_ftm_responder_params, clarify docs,
move validation into policy]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the NL80211_KEY_IDX attribute inside the NL80211_ATTR_KEY in
NL80211_CMD_GET_KEY responses to comply with nl80211_key_policy.
This is unlikely to affect existing userspace.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's a bit of duplicated code to initialize a wdev, pull it out
into a separate function to call from both places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The check for !scan_plan is redunant as this has been checked
in the proceeding statement and the code returns -ENOBUFS if
it is true. Remove the redundant check.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The iterator in list_for_each_entry_safe is never null, therefore, remove
the redundant null pointer check.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_wext_giwrate and sinfo.pertid might allocate sinfo.pertid via
rdev_get_station(), but never release it. Fix that.
Fixes: 8689c051a2 ("cfg80211: dynamically allocate per-tid stats for station info")
Signed-off-by: Stefan Seyfried <seife+kernel@b1-systems.com>
[johannes: fix error path, use cfg80211_sinfo_release_content(), add Fixes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use array_index_nospec() to sanitize i with respect to speculation.
Note that the user doesn't control i directly, but can make it out
of bounds by not finding a threshold in the array.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
[add note about user control, as explained by Masashi]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use array_index_nospec() to sanitize ridx with respect to speculation.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_get_bss_channel() is used to update the RX channel based on the
available frame payload information (channel number from DSSS Parameter
Set element or HT Operation element). This is needed on 2.4 GHz channels
where frames may be received on neighboring channels due to overlapping
frequency range.
This might of some use on the 5 GHz band in some corner cases, but
things are more complex there since there is no n:1 or 1:n mapping
between channel numbers and frequencies due to multiple different
starting frequencies in different operating classes. This could result
in ieee80211_channel_to_frequency() returning incorrect frequency and
ieee80211_get_channel() returning incorrect channel information (or
indication of no match). In the previous implementation, this could
result in some scan results being dropped completely, e.g., for the 4.9
GHz channels. That prevented connection to such BSSs.
Fix this by using the driver-provided channel pointer if
ieee80211_get_channel() does not find matching channel data for the
channel number in the frame payload and if the scan is done with 5 MHz
or 10 MHz channel bandwidth. While doing this, also add comments
describing what the function is trying to achieve to make it easier to
understand what happens here and why.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add validation check for wmm rule when copy rules from fwdb and print
error when rule is invalid.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Core regulatory hints didn't set wiphy_idx to WIPHY_IDX_INVALID. Since
the regulatory request is zeroed, wiphy_idx was always implicitly set to
0. This resulted in updating only phy #0.
Fix that.
Fixes: 806a9e3967 ("cfg80211: make regulatory_request use wiphy_idx instead of wiphy")
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[add fixes tag]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IEEE 802.11-2016 extended the VHT capability fields to allow
indicating the number of spatial streams depending on the
actually used bandwidth, add support for decoding this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Same as for HT and VHT.
This helps the lower level to know whether the AP supports HE.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* various A-MSDU building fixes (currently only affects mt76)
* syzkaller & spectre fixes in hwsim
* TXQ vs. teardown fix that was causing crashes
* embed WMM info in reg rule, bad code here had been causing crashes
* one compilation issue with fix from Arnd (rfkill-gpio includes)
* fixes for a race and bad data during/after channel switch
* nl80211: a validation fix, attribute type & unit fixes
along with other small fixes.
-----BEGIN PGP SIGNATURE-----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=lLBA
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2018-09-03' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Here are quite a large number of fixes, notably:
* various A-MSDU building fixes (currently only affects mt76)
* syzkaller & spectre fixes in hwsim
* TXQ vs. teardown fix that was causing crashes
* embed WMM info in reg rule, bad code here had been causing crashes
* one compilation issue with fix from Arnd (rfkill-gpio includes)
* fixes for a race and bad data during/after channel switch
* nl80211: a validation fix, attribute type & unit fixes
along with other small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The "chandef->center_freq1" variable is a u32 but "freq" is a u16 so we
are truncating away the high bits. I noticed this bug because in commit
9cf0a0b4b6 ("cfg80211: Add support for 60GHz band channels 5 and 6")
we made "freq <= 56160 + 2160 * 6" a valid requency when before it was
only "freq <= 56160 + 2160 * 4" that was valid. It introduces a static
checker warning:
net/wireless/util.c:1571 ieee80211_chandef_to_operating_class()
warn: always true condition '(freq <= 56160 + 2160 * 6) => (0-u16max <= 69120)'
But really we probably shouldn't have been truncating the high bits
away to begin with.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
nl80211_update_ft_ies() tried to validate NL80211_ATTR_IE with
is_valid_ie_attr() before dereferencing it, but that helper function
returns true in case of NULL pointer (i.e., attribute not included).
This can result to dereferencing a NULL pointer. Fix that by explicitly
checking that NL80211_ATTR_IE is included.
Fixes: 355199e02b ("cfg80211: Extend support for IEEE 802.11r Fast BSS Transition")
Signed-off-by: Arunk Khandavalli <akhandav@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Modify the API to include all ACK frames in average ACK
signal strength reporting, not just ACKs for data frames.
Make exposing the data conditional on implementing the
extended feature flag.
This is how it was really implemented in mac80211, update
the code there to use the new defines and clean up some of
the setting code.
Keep nl80211.h source compatibility by keeping the old names.
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
[rewrite commit log, change compatibility to be old=new
instead of the other way around, update kernel-doc,
roll in mac80211 changes, make mac80211 depend on valid
bit instead of HW flag]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
freq_reg_info expects to get the frequency in kHz. Instead we
accidently pass it in MHz. Thus, currently the function always
return ERR rule. Fix that.
Fixes: 50f32718e1 ("nl80211: Add wmm rule attribute to NL80211_CMD_GET_WIPHY dump command")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[fix kHz/MHz in commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
TXOP (also known as Channel Occupancy Time) is u16 and should be
added using nla_put_u16 instead of u8, fix that.
Fixes: 50f32718e1 ("nl80211: Add wmm rule attribute to NL80211_CMD_GET_WIPHY dump command")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current support in the 60GHz band is for channels 1-4.
Add support for channels 5 and 6.
This requires enlarging ieee80211_channel.center_freq from u16 to u32.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When REGULATORY_COUNTRY_IE_IGNORE is set, __reg_process_hint_country_ie()
ignores the country code change request from __cfg80211_connect_result()
via regulatory_hint_country_ie().
After Disconnect, similar to above, country code should not be reset to
world when country IE ignore is set. But this is violated and restore of
regulatory settings is invoked by cfg80211_disconnect_work via
regulatory_hint_disconnect().
To address this, avoid regulatory restore from regulatory_hint_disconnect()
when COUNTRY_IE_IGNORE is set.
Note: Currently, restore_regulatory_settings() takes care of clearing
beacon hints. But in the proposed change, regulatory restore is avoided.
Therefore, explicitly clear beacon hints when DISABLE_BEACON_HINTS
is not set.
Signed-off-by: Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make ieee80211_send_layer2_update() a common function so other drivers
can re-use it.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make wmm_rule be part of the reg_rule structure. This simplifies the
code a lot at the cost of having bigger memory usage. However in most
cases we have only few reg_rule's and when we do have many like in
iwlwifi we do not save memory as it allocates a separate wmm_rule for
each channel anyway.
This also fixes a bug reported in various places where somewhere the
pointers were corrupted and we ended up doing a null-dereference.
Fixes: 230ebaa189 ("cfg80211: read wmm rules from regulatory database")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
[rephrase commit message slightly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pointer arithmetic already adjusts by the size of the struct,
so the sizeof() calculation is wrong. This is basically the
same as Colin King's patch for similar code in the iwlwifi
driver.
Fixes: 230ebaa189 ("cfg80211: read wmm rules from regulatory database")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In preparing to remove all stack VLA usage from the kernel[1], this
removes the discouraged use of AHASH_REQUEST_ON_STACK in favor of
the smaller SHASH_DESC_ON_STACK by converting from ahash-wrapped-shash
to direct shash. The stack allocation will be made a fixed size in a
later patch to the crypto subsystem.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently user regulatory hint is ignored if all wiphys
in the system are self managed. But the hint is not ignored
if there is no wiphy in the system. This affects the global
regulatory setting. Global regulatory setting needs to be
maintained so that it can be applied to a new wiphy entering
the system. Therefore, do not ignore user regulatory setting
even if all wiphys in the system are self managed.
Signed-off-by: Amar Singhal <asinghal@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I was looking at usually suppressed gcc warnings,
[-Wimplicit-fallthrough=] in this case:
The code definitely looks like a break is missing here.
However I am not able to test the NL80211_IFTYPE_MESH_POINT,
nor do I actually know what might be :)
So please use this patch with caution and only if you are
able to do some testing.
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
[johannes: looks obvious enough to apply as is, interesting
though that it never seems to have been a problem]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current implementation of cfg80211_rx_control_port assumed that the
caller could provide a contiguous region of memory for the control port
frame to be sent up to userspace. Unfortunately, many drivers produce
non-linear skbs, especially for data frames. This resulted in userspace
getting notified of control port frames with correct metadata (from
address, port, etc) yet garbage / nonsense contents, resulting in bad
handshakes, disconnections, etc.
mac80211 linearizes skbs containing management frames. But it didn't
seem worthwhile to do this for control port frames. Thus the signature
of cfg80211_rx_control_port was changed to take the skb directly.
nl80211 then takes care of obtaining control port frame data directly
from the (linear | non-linear) skb.
The caller is still responsible for freeing the skb,
cfg80211_rx_control_port does not take ownership of it.
Fixes: 6a671a50f8 ("nl80211: Add CMD_CONTROL_PORT_FRAME API")
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
[fix some kernel-doc formatting, add fixes tag]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Simple overlapping changes in stmmac driver.
Adjust skb_gro_flush_final_remcsum function signature to make GRO list
changes in net-next, as per Stephen Rothwell's example merge
resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
* finally some of the promised HE code, but it turns
out to be small - but everything kept changing, so
one part I did in the driver was >30 patches for
what was ultimately <200 lines of code ... similar
here for this code.
* improved scan privacy support - can now specify scan
flags for randomizing the sequence number as well as
reducing the probe request element content
* rfkill cleanups
* a timekeeping cleanup from Arnd
* various other cleanups
-----BEGIN PGP SIGNATURE-----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=sNaA
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-06-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Small merge conflict in net/mac80211/scan.c, I preserved
the kcalloc() conversion. -DaveM
Johannes Berg says:
====================
This round's updates:
* finally some of the promised HE code, but it turns
out to be small - but everything kept changing, so
one part I did in the driver was >30 patches for
what was ultimately <200 lines of code ... similar
here for this code.
* improved scan privacy support - can now specify scan
flags for randomizing the sequence number as well as
reducing the probe request element content
* rfkill cleanups
* a timekeeping cleanup from Arnd
* various other cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The BIT macro uses unsigned long which some architectures handle as 32 bit
and therefore might cause macro's shift to overflow when used on a value
equals or larger than 32 (NL80211_STA_INFO_RX_DURATION and afterwards).
Since 'filled' member in station_info changed to u64, BIT_ULL macro
should be used with all NL80211_STA_INFO_* attribute types instead of BIT
to prevent future possible bugs when one will use BIT macro for higher
attributes by mistake.
This commit cleans up all usages of BIT macro with the above field
in cfg80211 by changing it to BIT_ULL instead. In addition, there are
some places which don't use BIT nor BIT_ULL macros so align those as well.
Signed-off-by: Omer Efrat <omer.efrat@tandemg.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The cfg80211 layer uses get_seconds() to read the current time
in its supend handling. This function is deprecated because of the 32-bit
time_t overflow, and it can cause unexpected behavior when the time
changes due to settimeofday() calls or leap second updates.
In many cases, we want to use monotonic time instead, however cfg80211
explicitly tracks the time spent in suspend, so this changes the
driver over to use ktime_get_boottime_seconds(), which is slightly
slower, but not used in a fastpath here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At the very least we should check the return value if
nla_parse_nested() is called with a non-NULL policy.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 9757235f45, "nl80211: correct checks for
NL80211_MESHCONF_HT_OPMODE value") relaxed the range for the HT
operation field in meshconf, while also adding checks requiring
the non-greenfield and non-ht-sta bits to be set in certain
circumstances. The latter bit is actually reserved for mesh BSSes
according to Table 9-168 in 802.11-2016, so in fact it should not
be set.
wpa_supplicant sets these bits because the mesh and AP code share
the same implementation, but authsae does not. As a result, some
meshconf updates from authsae which set only the NONHT_MIXED
protection bits were being rejected.
In order to avoid breaking userspace by changing the rules again,
simply accept the values with or without the bits set, and mask
off the reserved bit to match the spec.
While in here, update the 802.11-2012 reference to 802.11-2016.
Fixes: 9757235f45 ("nl80211: correct checks for NL80211_MESHCONF_HT_OPMODE value")
Cc: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Reviewed-by: Masashi Honma <masashi.honma@gmail.com>
Reviewed-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking fixes from David Miller:
1) Various netfilter fixlets from Pablo and the netfilter team.
2) Fix regression in IPVS caused by lack of PMTU exceptions on local
routes in ipv6, from Julian Anastasov.
3) Check pskb_trim_rcsum for failure in DSA, from Zhouyang Jia.
4) Don't crash on poll in TLS, from Daniel Borkmann.
5) Revert SO_REUSE{ADDR,PORT} change, it regresses various things
including Avahi mDNS. From Bart Van Assche.
6) Missing of_node_put in qcom/emac driver, from Yue Haibing.
7) We lack checking of the TCP checking in one special case during SYN
receive, from Frank van der Linden.
8) Fix module init error paths of mac80211 hwsim, from Johannes Berg.
9) Handle 802.1ad properly in stmmac driver, from Elad Nachman.
10) Must grab HW caps before doing quirk checks in stmmac driver, from
Jose Abreu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
net: stmmac: Run HWIF Quirks after getting HW caps
neighbour: skip NTF_EXT_LEARNED entries during forced gc
net: cxgb3: add error handling for sysfs_create_group
tls: fix waitall behavior in tls_sw_recvmsg
tls: fix use-after-free in tls_push_record
l2tp: filter out non-PPP sessions in pppol2tp_tunnel_ioctl()
l2tp: reject creation of non-PPP sessions on L2TPv2 tunnels
mlxsw: spectrum_switchdev: Fix port_vlan refcounting
mlxsw: spectrum_router: Align with new route replace logic
mlxsw: spectrum_router: Allow appending to dev-only routes
ipv6: Only emit append events for appended routes
stmmac: added support for 802.1ad vlan stripping
cfg80211: fix rcu in cfg80211_unregister_wdev
mac80211: Move up init of TXQs
mac80211_hwsim: fix module init error paths
cfg80211: initialize sinfo in cfg80211_get_station
nl80211: fix some kernel doc tag mistakes
hv_netvsc: Fix the variable sizes in ipsecv2 and rsc offload
rds: avoid unenecessary cong_update in loop transport
l2tp: clean up stale tunnel or session in pppol2tp_connect's error path
...
Add support for the HE in cfg80211 and also add userspace API to
nl80211 to send rate information out, conforming with P802.11ax_D2.0.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
User space tools might be interested in knowing the current
status of the 4ADDR property of an interface (when supported).
Send the status along with the other attributes when replying
to a GET_INTERFACE netlink query.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Add the scan flags for randomized SN and minimized probe request
content for improved scan privacy.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
There's a very common pattern to check for a scan flag and
then reject it if an extended feature flag isn't set, factor
this out into a helper function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
The arguments should be (# of elements, size of each) instead
of the other way around, which really ends up being mostly
equivalent but smatch complains about it, so swap them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Callers of cfg80211_unregister_wdev can free the wdev object
immediately after this function returns. This may crash the kernel
because this wdev object is still in use by other threads.
Add synchronize_rcu() after list_del_rcu to make sure wdev object can
be safely freed.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Most of the implementations behind cfg80211_get_station will not initialize
sinfo to zero before manipulating it. For example, the member "filled",
which indicates the filled in parts of this struct, is often only modified
by enabling certain bits in the bitfield while keeping the remaining bits
in their original state. A caller without a preinitialized sinfo.filled can
then no longer decide which parts of sinfo were filled in by
cfg80211_get_station (or actually the underlying implementations).
cfg80211_get_station must therefore take care that sinfo is initialized to
zero. Otherwise, the caller may tries to read information which was not
filled in and which must therefore also be considered uninitialized. In
batadv_v_elp_get_throughput's case, an invalid "random" expected throughput
may be stored for this neighbor and thus the B.A.T.M.A.N V algorithm may
switch to non-optimal neighbors for certain destinations.
Fixes: 7406353d43 ("cfg80211: implement cfg80211_get_station cfg80211 API")
Reported-by: Thomas Lauer <holminateur@gmail.com>
Reported-by: Marcel Schmidt <ff.z-casparistrasse@mailbox.org>
Cc: b.a.t.m.a.n@lists.open-mesh.org
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Pull networking updates from David Miller:
1) Add Maglev hashing scheduler to IPVS, from Inju Song.
2) Lots of new TC subsystem tests from Roman Mashak.
3) Add TCP zero copy receive and fix delayed acks and autotuning with
SO_RCVLOWAT, from Eric Dumazet.
4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard
Brouer.
5) Add ttl inherit support to vxlan, from Hangbin Liu.
6) Properly separate ipv6 routes into their logically independant
components. fib6_info for the routing table, and fib6_nh for sets of
nexthops, which thus can be shared. From David Ahern.
7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP
messages from XDP programs. From Nikita V. Shirokov.
8) Lots of long overdue cleanups to the r8169 driver, from Heiner
Kallweit.
9) Add BTF ("BPF Type Format"), from Martin KaFai Lau.
10) Add traffic condition monitoring to iwlwifi, from Luca Coelho.
11) Plumb extack down into fib_rules, from Roopa Prabhu.
12) Add Flower classifier offload support to igb, from Vinicius Costa
Gomes.
13) Add UDP GSO support, from Willem de Bruijn.
14) Add documentation for eBPF helpers, from Quentin Monnet.
15) Add TLS tx offload to mlx5, from Ilya Lesokhin.
16) Allow applications to be given the number of bytes available to read
on a socket via a control message returned from recvmsg(), from
Soheil Hassas Yeganeh.
17) Add x86_32 eBPF JIT compiler, from Wang YanQing.
18) Add AF_XDP sockets, with zerocopy support infrastructure as well.
From Björn Töpel.
19) Remove indirect load support from all of the BPF JITs and handle
these operations in the verifier by translating them into native BPF
instead. From Daniel Borkmann.
20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha.
21) Allow XDP programs to do lookups in the main kernel routing tables
for forwarding. From David Ahern.
22) Allow drivers to store hardware state into an ELF section of kernel
dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy.
23) Various RACK and loss detection improvements in TCP, from Yuchung
Cheng.
24) Add TCP SACK compression, from Eric Dumazet.
25) Add User Mode Helper support and basic bpfilter infrastructure, from
Alexei Starovoitov.
26) Support ports and protocol values in RTM_GETROUTE, from Roopa
Prabhu.
27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard
Brouer.
28) Add lots of forwarding selftests, from Petr Machata.
29) Add generic network device failover driver, from Sridhar Samudrala.
* ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits)
strparser: Add __strp_unpause and use it in ktls.
rxrpc: Fix terminal retransmission connection ID to include the channel
net: hns3: Optimize PF CMDQ interrupt switching process
net: hns3: Fix for VF mailbox receiving unknown message
net: hns3: Fix for VF mailbox cannot receiving PF response
bnx2x: use the right constant
Revert "net: sched: cls: Fix offloading when ingress dev is vxlan"
net: dsa: b53: Fix for brcm tag issue in Cygnus SoC
enic: fix UDP rss bits
netdev-FAQ: clarify DaveM's position for stable backports
rtnetlink: validate attributes in do_setlink()
mlxsw: Add extack messages for port_{un, }split failures
netdevsim: Add extack error message for devlink reload
devlink: Add extack to reload and port_{un, }split operations
net: metrics: add proper netlink validation
ipmr: fix error path when ipmr_new_table fails
ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds
net: hns3: remove unused hclgevf_cfg_func_mta_filter
netfilter: provide udp*_lib_lookup for nf_tproxy
qed*: Utilize FW 8.37.2.0
...
Reject NL80211_CMD_DISCONNECT, NL80211_CMD_DISASSOCIATE,
NL80211_CMD_DEAUTHENTICATE and NL80211_CMD_ASSOCIATE commands
from clients other than the connection owner set in the connect,
authenticate or associate commands, if it was set.
The main point of this check is to prevent chaos when two processes
try to use nl80211 at the same time, it's not a security measure.
The same thing should possibly be done for JOIN_IBSS/LEAVE_IBSS and
START_AP/STOP_AP.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use NL80211_CMD_UPDATE_CONNECT_PARAMS to update new ERP information,
Association IEs and the Authentication type to driver / firmware which
will be used in subsequent roamings.
Signed-off-by: Vidyullatha Kanchanapally <vidyullatha@codeaurora.org>
[arend: extended fils-sk kernel doc and added check in wiphy_register()]
Reviewed-by: Jithu Jance <jithu.jance@broadcom.com>
Reviewed-by: Eylon Pedinovsky <eylon.pedinovsky@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of FILS shared key offload the parameters can change
upon roaming of which user-space needs to be notified.
Reviewed-by: Jithu Jance <jithu.jance@broadcom.com>
Reviewed-by: Eylon Pedinovsky <eylon.pedinovsky@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Put FILS related parameters into their own struct definition so
it can be reused for roam events in subsequent change.
Reviewed-by: Jithu Jance <jithu.jance@broadcom.com>
Reviewed-by: Eylon Pedinovsky <eylon.pedinovsky@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Only invoke cfg80211_bss_expire on the first nl80211_dump_scan
invocation to avoid (likely) redundant processing.
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Bring in net-next which had pulled in net, so I have the changes
from mac80211 and can apply a patch that would otherwise conflict.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers may call this function when regdb is not initialized yet,
so we need to make sure regdb is valid before trying to access it.
Make sure regdb is initialized before trying to access it in
reg_query_regdb_wmm() and query_regdb().
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 7ea3e110f2 seems to have
introduced:
net/wireless/nl80211.c: In function ‘nl80211_get_station’:
net/wireless/nl80211.c:4802:34: error: incompatible type for argument 1 of ‘cfg80211_sinfo_release_content’
cfg80211_sinfo_release_content(sinfo);
^~~~~
In file included from net/wireless/nl80211.c:24:0:
./include/net/cfg80211.h:5721:20: note: expected ‘struct station_info *’ but argument is of type ‘struct station_info’
static inline void cfg80211_sinfo_release_content(struct station_info *sinfo)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 7ea3e110f2 ("cfg80211: release station info tidstats where needed")
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This fixes memory leaks in cases where we got the station
info but failed sending it out properly.
Fixes: 8689c051a2 ("cfg80211: dynamically allocate per-tid stats for station info")
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Trivial fix to spelling mistake in pr_debug message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arend's previous patch made the sinfo structure smaller
again by to dynamically allocating the per-tid stats
only when needed. Thus, revert to stack allocation for
the struct to simplify the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With the addition of TXQ stats in the per-tid statistics the struct
station_info grew significantly. This resulted in stack size warnings
due to the structure itself being above the limit for the warnings.
Add an allocation function that those who want to provide per-tid
stats should use to allocate the tid array, i.e.
struct station_info::pertid.
Cc: Toke Høiland-Jørgensen <toke@toke.dk>
Fixes: 52539ca89f ("cfg80211: Expose TXQ stats and parameters to userspace")
Signed-off-by: Arend van Spriel <aspriel@gmail.com>
[johannes: fix missing BIT() and logic by removing]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allocation size of nlmsg in cfg80211_ft_event is based on ric_ies_len
and doesn't take into account ies_len. This leads to
NL80211_CMD_FT_EVENT message construction failure in case ft_event
contains large enough ies buffer.
Add ies_len to the nlmsg allocation size.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Variants of proc_create{,_data} that directly take a struct seq_operations
and deal with network namespaces in ->open and ->release. All callers of
proc_create + seq_open_net converted over, and seq_{open,release}_net are
removed entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
This adds support for exporting the mac80211 TXQ stats via nl80211 by
way of a nested TXQ stats attribute, as well as for configuring the
quantum and limits that were previously only changeable through debugfs.
This commit adds just the nl80211 API, a subsequent commit adds support to
mac80211 itself.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Average ack rssi will be given to userspace via NL80211 interface
if firmware is capable. Userspace tool ‘iw’ can process this
information and give the output as one of the fields in
‘iw dev wlanX station dump’.
Example output :
localhost ~ #iw dev wlan-5000mhz station dump Station
34:f3:9a:aa:3b:29 (on wlan-5000mhz)
inactive time: 5370 ms
rx bytes: 85321
rx packets: 576
tx bytes: 14225
tx packets: 71
tx retries: 0
tx failed: 2
beacon loss: 0
rx drop misc: 0
signal: -54 dBm
signal avg: -53 dBm
tx bitrate: 866.7 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 2
rx bitrate: 866.7 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 2
avg ack signal: -56 dBm
authorized: yes
authenticated: yes
associated: yes
preamble: short
WMM/WME: yes
MFP: no
TDLS peer: no
DTIM period: 2
beacon interval:100
short preamble: yes
short slot time:yes
connected time: 203 seconds
Main use case is to measure the signal strength of a connected station
to AP. Data packet transmit rates and bandwidth used by station can vary
a lot even if the station is at fixed location, especially if the rates
used are multi stream(2stream, 3stream) rates with different bandwidth(20/40/80 Mhz).
These multi stream rates are sensitive and station can use different transmit power
for each of the rate and bandwidth combinations. RSSI measured from these RX packets
on AP will be not stable and can vary a lot with in a short time.
Whereas 802.11 ack frames from station are sent relatively at a constant
rate (6/12/24 Mbps) with constant bandwidth(20 Mhz).
So average rssi of the ack packets is good and more accurate.
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the regulatory core does not call the regulatory callback
reg_notifier for self managed wiphys, but regulatory_hint_user() call is
independent of wiphy and is meant for all wiphys in the system. Even a
self managed wiphy may be interested in regulatory_hint_user() to know
the country code from a trusted regulatory domain change like a cellular
base station. Therefore, for the regulatory source
NL80211_REGDOM_SET_BY_USER and the user hint type
NL80211_USER_REG_HINT_CELL_BASE, call the regulatory notifier.
No current wlan driver uses the REGULATORY_WIPHY_SELF_MANAGED flag while
also registering the reg_notifier regulatory callback, therefore there
will be no impact on existing drivers without them being explicitly
modified to take advantage of this new possibility.
Signed-off-by: Amar Singhal <asinghal@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will serve userspace entity to maintain its regulatory limitation.
More specifcally APs can use this data to calculate the WMM IE when
building: beacons, probe responses, assoc responses etc...
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The failure scenario while processing
NL80211_ATTR_EXTERNAL_AUTH_SUPPORT does not free
the connkeys. This commit addresses the same.
Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
'wmm_ptrs' is malloced in regdb_query_country() and should be freed
before leaving from the error handling cases, otherwise it will cause
memory leak.
Fixes: 230ebaa189 ("cfg80211: read wmm rules from regulatory database")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
[johannes: add Fixes tag]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The 'country IE' messages in the log can be confusing and make people think
that the country code has been set to Ireland. Fix this by changing the
log messages to use 'country element' instead (as they are no longer called
'information element' in the spec anyway).
Reported-by: Bernhard Gabler <Bernhard_Gabler@web.de>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's currently no limit on wiphy names, other than netlink
message size and memory limitations, but that causes issues when,
for example, the wiphy name is used in a uevent, e.g. in rfkill
where we use the same name for the rfkill instance, and then the
buffer there is "only" 2k for the environment variables.
This was reported by syzkaller, which used a 4k name.
Limit the name to something reasonable, I randomly picked 128.
Reported-by: syzbot+230d9e642a85d3fec29c@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-03-31
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add raw BPF tracepoint API in order to have a BPF program type that
can access kernel internal arguments of the tracepoints in their
raw form similar to kprobes based BPF programs. This infrastructure
also adds a new BPF_RAW_TRACEPOINT_OPEN command to BPF syscall which
returns an anon-inode backed fd for the tracepoint object that allows
for automatic detach of the BPF program resp. unregistering of the
tracepoint probe on fd release, from Alexei.
2) Add new BPF cgroup hooks at bind() and connect() entry in order to
allow BPF programs to reject, inspect or modify user space passed
struct sockaddr, and as well a hook at post bind time once the port
has been allocated. They are used in FB's container management engine
for implementing policy, replacing fragile LD_PRELOAD wrapper
intercepting bind() and connect() calls that only works in limited
scenarios like glibc based apps but not for other runtimes in
containerized applications, from Andrey.
3) BPF_F_INGRESS flag support has been added to sockmap programs for
their redirect helper call bringing it in line with cls_bpf based
programs. Support is added for both variants of sockmap programs,
meaning for tx ULP hooks as well as recv skb hooks, from John.
4) Various improvements on BPF side for the nfp driver, besides others
this work adds BPF map update and delete helper call support from
the datapath, JITing of 32 and 64 bit XADD instructions as well as
offload support of bpf_get_prandom_u32() call. Initial implementation
of nfp packet cache has been tackled that optimizes memory access
(see merge commit for further details), from Jakub and Jiong.
5) Removal of struct bpf_verifier_env argument from the print_bpf_insn()
API has been done in order to prepare to use print_bpf_insn() soon
out of perf tool directly. This makes the print_bpf_insn() API more
generic and pushes the env into private data. bpftool is adjusted
as well with the print_bpf_insn() argument removal, from Jiri.
6) Couple of cleanups and prep work for the upcoming BTF (BPF Type
Format). The latter will reuse the current BPF verifier log as
well, thus bpf_verifier_log() is further generalized, from Martin.
7) For bpf_getsockopt() and bpf_setsockopt() helpers, IPv4 IP_TOS read
and write support has been added in similar fashion to existing
IPv6 IPV6_TCLASS socket option we already have, from Nikita.
8) Fixes in recent sockmap scatterlist API usage, which did not use
sg_init_table() for initialization thus triggering a BUG_ON() in
scatterlist API when CONFIG_DEBUG_SG was enabled. This adds and
uses a small helper sg_init_marker() to properly handle the affected
cases, from Prashant.
9) Let the BPF core follow IDR code convention and therefore use the
idr_preload() and idr_preload_end() helpers, which would also help
idr_alloc_cyclic() under GFP_ATOMIC to better succeed under memory
pressure, from Shaohua.
10) Last but not least, a spelling fix in an error message for the
BPF cookie UID helper under BPF sample code, from Colin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
first bullet here:
* EAPoL-over-nl80211 from Denis - this will let us fix
some long-standing issues with bridging, races with
encryption and more
* DFS offload support from the qtnfmac folks
* regulatory database changes for the new ETSI adaptivity
requirements
* various other fixes and small enhancements
-----BEGIN PGP SIGNATURE-----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=hI0F
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
We have a fair number of patches, but many of them are from the
first bullet here:
* EAPoL-over-nl80211 from Denis - this will let us fix
some long-standing issues with bridging, races with
encryption and more
* DFS offload support from the qtnfmac folks
* regulatory database changes for the new ETSI adaptivity
requirements
* various other fixes and small enhancements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This function iterates over net_namespace_list and flushes
the queue for every of them. What does this rtnl_lock()
protects?! Since we may add skbs to net::wext_nlevents
without rtnl_lock(), it does not protects us about queuers.
It guarantees, two threads can't flush the queue in parallel,
that can change the order, but since skb can be queued
in any order, it doesn't matter, how many threads do this
in parallel. In case of several threads, this will be even
faster.
So, we can remove rtnl_lock() here, as it was used for
iteration over net_namespace_list only.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl_lock() is used everywhere, and contention is very high.
When someone wants to iterate over alive net namespaces,
he/she has no a possibility to do that without exclusive lock.
But the exclusive rtnl_lock() in such places is overkill,
and it just increases the contention. Yes, there is already
for_each_net_rcu() in kernel, but it requires rcu_read_lock(),
and this can't be sleepable. Also, sometimes it may be need
really prevent net_namespace_list growth, so for_each_net_rcu()
is not fit there.
This patch introduces new rw_semaphore, which will be used
instead of rtnl_mutex to protect net_namespace_list. It is
sleepable and allows not-exclusive iterations over net
namespaces list. It allows to stop using rtnl_lock()
in several places (what is made in next patches) and makes
less the time, we keep rtnl_mutex. Here we just add new lock,
while the explanation of we can remove rtnl_lock() there are
in next patches.
Fine grained locks generally are better, then one big lock,
so let's do that with net_namespace_list, while the situation
allows that.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit implements the TX side of NL80211_CMD_CONTROL_PORT_FRAME.
Userspace provides the raw EAPoL frame using NL80211_ATTR_FRAME.
Userspace should also provide the destination address and the protocol
type to use when sending the frame. This is used to implement TX of
Pre-authentication frames. If CONTROL_PORT_ETHERTYPE_NO_ENCRYPT is
specified, then the driver will be asked not to encrypt the outgoing
frame.
A new EXT_FEATURE flag is introduced so that nl80211 code can check
whether a given wiphy has capability to pass EAPoL frames over nl80211.
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit also adds cfg80211_rx_control_port function. This is used
to generate a CMD_CONTROL_PORT_FRAME event out to userspace. The
conn_owner_nlportid is used as the unicast destination. This means that
userspace must specify NL80211_ATTR_SOCKET_OWNER flag if control port
over nl80211 routing is requested in NL80211_CMD_CONNECT,
NL80211_CMD_ASSOCIATE, NL80211_CMD_START_AP or IBSS/mesh join.
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
[johannes: fix return value of cfg80211_rx_control_port()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In general regulatory self managed devices maintain their own
regulatory profiles thus it doesn't have to query the regulatory database
on country change.
ETSI has recently introduced a new channel access mechanism for 5GHz
that all wlan devices need to comply with.
These values are stored in the regulatory database.
There are self managed devices which can't maintain these
values on their own. Add API to allow self managed regulatory devices
to query the regulatory database for high band wmm rule.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[johannes: fix documentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The whole code is set up to allow RCU reads of this data, but
then uses rtnl_dereference() which requires the RTNL. Convert
it to rcu_dereference_rtnl() which makes it require only RCU
or the RTNL, to allow RCU-protected reading of the data.
Reviewed-by: Coelho, Luciano <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ETSI EN 301 893 v2.1.1 (2017-05) standard defines a new channel access
mechanism that all devices (WLAN and LAA) need to comply with.
The regulatory database can now be loaded into the kernel and also
has the option to load optional data.
In order to be able to comply with ETSI standard, we add wmm_rule into
regulatory rule and add the option to read its value from the regulatory
database.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[johannes: fix memory leak in error path]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
[johannes: fix race with wdev lock/unlock by just acquiring once]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
[johannes: fix race with wdev lock/unlock by just acquiring once]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently autodisconnect_wk assumes that only interface types of
P2P_CLIENT and STATION use conn_owner_nlportid. Change this so all
interface types are supported.
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently channel switch/start_ap to DFS channel cannot be done to
non-CAC-cleared channel even if DFS offload if enabled.
Make non-cleared DFS channels available if DFS offload is enabled.
CAC will be started by HW after channel change, start_ap call, etc.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Exclude CAC_STARTED event from !wdev->cac_started check,
since cac_started will be set later in the same function.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- fix trace_hfi1_ctxt_info() to pass large struct by reference instead of by value
- convert 'type array[]' tracepoint arguments into 'type *array',
since compiler will warn that sizeof('type array[]') == sizeof('type *array')
and later should be used instead
The CAST_TO_U64 macro in the later patch will enforce that tracepoint
arguments can only be integers, pointers, or less than 8 byte structures.
Larger structures should be passed by reference.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Synchronous pernet_operations are not allowed anymore.
All are asynchronous. So, drop the structure member.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wiphy EXT_FEATURE flag to indicate that HW or driver does
all DFS actions by itself.
User-space functionality already implemented in hostapd using
vendor-specific (QCA) OUI to advertise DFS offload support.
Need to introduce generic flag to inform about DFS offload support.
For devices with DFS_OFFLOAD flag set user-space will no longer
need to issue CAC or do any actions in response to
"radar detected" events. HW will do everything by itself and send
events to user-space to indicate that CAC was started/finished, etc.
Signed-off-by: Dmitrii Lebed <dlebed@quantenna.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
CAC_STARTED event is needed for DFS offload feature and
should be generated by driver/HW if DFS_OFFLOAD is enabled.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
Only works if the IV was stripped from packets. Create a smaller
variant of ieee80211_rx_h_amsdu, which bypasses checks already done
within the fast-rx context.
In order to do so, update cfg80211's ieee80211_data_to_8023_exthdr()
to take the offset between header and snap.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
New options introduced by the patch this fixes are still
enabled even if CFG80211 is disabled.
.config:
# CONFIG_CFG80211 is not set
CONFIG_CFG80211_REQUIRE_SIGNED_REGDB=y
CONFIG_CFG80211_USE_KERNEL_REGDB_KEYS=y
# CONFIG_LIB80211 is not set
When CFG80211_REQUIRE_SIGNED_REGDB is enabled, it selects
SYSTEM_DATA_VERIFICATION which selects SYSTEM_TRUSTED_KEYRING
that need extract-cert tool. extract-cert needs some openssl
headers to be installed on the build machine.
Instead of adding missing "depends on CFG80211", it's
easier to use a 'if' block around all options related
to CFG80211, so do that.
Fixes: 90a53e4432 ("cfg80211: implement regdb signature checking")
Signed-off-by: Romain Naour <romain.naour@gmail.com>
[touch up commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
One thing to note: I've included a new ethertype
that wireless uses (ETH_P_PREAUTH) in if_ether.h.
-----BEGIN PGP SIGNATURE-----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=A6XK
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Various updates across wireless.
One thing to note: I've included a new ethertype
that wireless uses (ETH_P_PREAUTH) in if_ether.h.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
cfg80211: fix cfg80211_beacon_dup
-> old bug in this code
cfg80211: clear wep keys after disconnection
-> certain ways of disconnecting left the keys
mac80211: round IEEE80211_TX_STATUS_HEADROOM up to multiple of 4
-> alignment issues with using 14 bytes
mac80211: Do not disconnect on invalid operating class
-> if the AP has a bogus operating class, let it be
mac80211: Fix sending ADDBA response for an ongoing session
-> don't send the same frame twice
cfg80211: use only 1Mbps for basic rates in mesh
-> interop issue with old versions of our code
mac80211_hwsim: don't use WQ_MEM_RECLAIM
-> it causes splats because it flushes work on a non-reclaim WQ
regulatory: add NUL to request alpha2
-> nla_put_string() issue from Kees
mac80211: mesh: fix wrong mesh TTL offset calculation
-> protocol issue
mac80211: fix a possible leak of station stats
-> error path might leak memory
mac80211: fix calling sleeping function in atomic context
-> percpu allocations need to be made with gfp flags
-----BEGIN PGP SIGNATURE-----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=kwiY
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2018-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Various fixes across the tree, the shortlog basically says it all:
cfg80211: fix cfg80211_beacon_dup
-> old bug in this code
cfg80211: clear wep keys after disconnection
-> certain ways of disconnecting left the keys
mac80211: round IEEE80211_TX_STATUS_HEADROOM up to multiple of 4
-> alignment issues with using 14 bytes
mac80211: Do not disconnect on invalid operating class
-> if the AP has a bogus operating class, let it be
mac80211: Fix sending ADDBA response for an ongoing session
-> don't send the same frame twice
cfg80211: use only 1Mbps for basic rates in mesh
-> interop issue with old versions of our code
mac80211_hwsim: don't use WQ_MEM_RECLAIM
-> it causes splats because it flushes work on a non-reclaim WQ
regulatory: add NUL to request alpha2
-> nla_put_string() issue from Kees
mac80211: mesh: fix wrong mesh TTL offset calculation
-> protocol issue
mac80211: fix a possible leak of station stats
-> error path might leak memory
mac80211: fix calling sleeping function in atomic context
-> percpu allocations need to be made with gfp flags
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch finishes converting pernet_operations
registered in net/wireless directory.
These pernet_operations have only exit method,
which moves devices to init_net. This action
is not pernet_operations-specific, and function
cfg80211_switch_netns() may be called all time
during the system life. All necessary protection
against concurrent cfg80211_pernet_exit() is made
by rtnl_lock(). So, cfg80211_pernet_ops is able
to be marked as async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a low level driver calls cfg80211_disconnected(), wep keys are
not cleared. As a result, following connection requests will fail
since cfg80211 internal state shows a connection is still in progress.
Fix this by clearing the wep keys when disconnecting.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch provides support to get ack signal in probe client response
and in station info from user.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
[squash in compilation fixes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Unfortunately removal of the ext_feature flag in the last revision of
the patch ended up negating the comparison and prevented the command
from being processed (either nl80211_external_auth() or
rdev_external_auth() returns -EOPNOTSUPP). Fix this by adding back the
lost '!'.
Fixes: 40cbfa9021 ("cfg80211/nl80211: Optional authentication offload to userspace")
Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we free the message immediately, there's no reason to
trim it back to the previous size.
Done with spatch:
@@
identifier msg, hdr;
@@
-if (hdr)
- genlmsg_cancel(msg, hdr);
... when != msg;
nlmsg_free(msg);
@@
identifier msg, hdr;
@@
-genlmsg_cancel(msg, hdr);
... when != msg;
nlmsg_free(msg);
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These pernet_operations initialize and purge net::wext_nlevents
queue, and are not touched by foreign pernet_operations.
Mark them async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull spectre/meltdown updates from Thomas Gleixner:
"The next round of updates related to melted spectrum:
- The initial set of spectre V1 mitigations:
- Array index speculation blocker and its usage for syscall,
fdtable and the n180211 driver.
- Speculation barrier and its usage in user access functions
- Make indirect calls in KVM speculation safe
- Blacklisting of known to be broken microcodes so IPBP/IBSR are not
touched.
- The initial IBPB support and its usage in context switch
- The exposure of the new speculation MSRs to KVM guests.
- A fix for a regression in x86/32 related to the cpu entry area
- Proper whitelisting for known to be safe CPUs from the mitigations.
- objtool fixes to deal proper with retpolines and alternatives
- Exclude __init functions from retpolines which speeds up the boot
process.
- Removal of the syscall64 fast path and related cleanups and
simplifications
- Removal of the unpatched paravirt mode which is yet another source
of indirect unproteced calls.
- A new and undisputed version of the module mismatch warning
- A couple of cleanup and correctness fixes all over the place
Yet another step towards full mitigation. There are a few things still
missing like the RBS underflow mitigation for Skylake and other small
details, but that's being worked on.
That said, I'm taking a belated christmas vacation for a week and hope
that everything is magically solved when I'm back on Feb 12th"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
KVM/SVM: Allow direct access to MSR_IA32_SPEC_CTRL
KVM/VMX: Allow direct access to MSR_IA32_SPEC_CTRL
KVM/VMX: Emulate MSR_IA32_ARCH_CAPABILITIES
KVM/x86: Add IBPB support
KVM/x86: Update the reverse_cpuid list to include CPUID_7_EDX
x86/speculation: Fix typo IBRS_ATT, which should be IBRS_ALL
x86/pti: Mark constant arrays as __initconst
x86/spectre: Simplify spectre_v2 command line parsing
x86/retpoline: Avoid retpolines for built-in __init functions
x86/kvm: Update spectre-v1 mitigation
KVM: VMX: make MSR bitmaps per-VCPU
x86/paravirt: Remove 'noreplace-paravirt' cmdline option
x86/speculation: Use Indirect Branch Prediction Barrier in context switch
x86/cpuid: Fix up "virtual" IBRS/IBPB/STIBP feature bits on Intel
x86/spectre: Fix spelling mistake: "vunerable"-> "vulnerable"
x86/spectre: Report get_user mitigation for spectre_v1
nl80211: Sanitize array index in parse_txq_params
vfs, fdtable: Prevent bounds-check bypass via speculative execution
x86/syscall: Sanitize syscall table de-references under speculation
x86/get_user: Use pointer masking to limit speculation
...
ht/vht action frames will be sent to AP from station to notify
change of its ht/vht opmode(max bandwidth, smps mode or nss) modified
values. Currently these valuse used by driver/firmware for rate control
algorithm. This patch introduces NL80211_CMD_STA_OPMODE_CHANGED
command to notify those modified/current supported values(max bandwidth,
smps mode, max nss) to userspace application. This will be useful for the
application like steering, which closely monitoring station's capability
changes. Since the application has taken these values during station
association.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit allows SAE Authentication for NL80211_CMD_CONNECT
interface, provided host driver advertises the support.
Host drivers may offload the SAE authentication to user space
through NL80211_CMD_EXTERNAL_AUTH interface and thus expect
the user space to advertise support to handle offload through
NL80211_ATTR_EXTERNAL_AUTH_SUPPORT in NL80211_CMD_CONNECT
request. Such drivers should reject the connect request on no
offload support from user space.
Signed-off-by: Srinivas Dasari <dasaris@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This interface allows the host driver to offload the authentication to
user space. This is exclusively defined for host drivers that do not
define separate commands for authentication and association, but rely on
userspace SME (e.g., in wpa_supplicant for the ~WPA_DRIVER_FLAGS_SME
case) for the authentication to happen. This can be used to implement
SAE without full implementation in the kernel/firmware while still being
able to use NL80211_CMD_CONNECT with driver-based BSS selection.
Host driver sends NL80211_CMD_EXTERNAL_AUTH event to start/abort
authentication to the port on which connect is triggered and status
of authentication is further indicated by user space to host
driver through the same command response interface.
User space entities advertise this capability through the
NL80211_ATTR_EXTERNAL_AUTH_SUPP flag in the NL80211_CMD_CONNECT request.
Host drivers shall look at this capability to offload the authentication.
Signed-off-by: Srinivas Dasari <dasaris@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[add socket connection ownership check]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit defines new scan flags (LOW_SPAN, LOW_POWER, HIGH_LATENCY)
to emphasize the requested scan behavior for the driver. These flags
are optional and are mutually exclusive. The implementation of the
respective functionality can be driver/hardware specific.
These flags can be used to control the compromise between how long
a scan takes, how much power it uses, and high accurate/complete
the scan is in finding the BSSs.
Signed-off-by: Sunil Dutt <usdutt@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mesh used to use the mandatory rates as basic rates, but we got
the calculation of mandatory rates wrong until some time ago.
Fix this this broke interoperability with older versions since
now more basic rates are required, and thus the MBSS isn't the
same and the network stops working.
Fix this by simply using only 1Mbps as the basic rate in 2.4GHz.
Since the changed mandatory rates only affected 2.4GHz, this is
all we need to make it work again.
Reported-and-tested-by: Matthias Schiffer <mschiffer@universe-factory.net>
Fixes: 1bd773c077 ("wireless: set correct mandatory rate flags")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The BPF verifier conflict was some minor contextual issue.
The TUN conflict was less trivial. Cong Wang fixed a memory leak of
tfile->tx_array in 'net'. This is an skb_array. But meanwhile in
net-next tun changed tfile->tx_arry into tfile->tx_ring which is a
ptr_ring.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix two places where the structure isn't initialized to zero,
and thus can't be filled properly by the driver.
Fixes: 4a4b816950 ("cfg80211: Accept multiple RSSI thresholds for CQM")
Fixes: 9930380f0b ("cfg80211: implement IWRATE")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
/proc has been ignoring struct file_operations::owner field for 10 years.
Specifically, it started with commit 786d7e1612
("Fix rmmod/read/write races in /proc entries"). Notice the chunk where
inode->i_fop is initialized with proxy struct file_operations for
regular files:
- if (de->proc_fops)
- inode->i_fop = de->proc_fops;
+ if (de->proc_fops) {
+ if (S_ISREG(inode->i_mode))
+ inode->i_fop = &proc_reg_file_ops;
+ else
+ inode->i_fop = de->proc_fops;
+ }
VFS stopped pinning module at this point.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported a warning from rfkill_alloc(), and after a while
I think that the reason is that it was doing fault injection and
the dev_set_name() failed, leaving the name NULL, and we didn't
check the return value and got to rfkill_alloc() with a NULL name.
Since we really don't want a NULL name, we ought to check the
return value.
Fixes: fb28ad3590 ("net: struct device - replace bus_id with dev_name(), dev_set_name()")
Reported-by: syzbot+1ddfb3357e1d7bb5b5d3@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When creating a new radio on the fly, hwsim allows this
to be done with an arbitrary number of channels, but
cfg80211 only supports a limited number of simultaneous
channels, leading to a warning.
Fix this by validating the number - this requires moving
the define for the maximum out to a visible header file.
Reported-by: syzbot+8dd9051ff19940290931@syzkaller.appspotmail.com
Fixes: b59ec8dd43 ("mac80211_hwsim: fix number of channels in interface combinations")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As ieee80211_bss_get_ie() derefences an RCU to return ssid_ie, both
the call to this function and any operation on this variable need
protection by the RCU read lock.
Fixes: 44905265bc ("nl80211: don't expose wdev->ssid for most interfaces")
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Paul reported that he got a report about undefined behaviour
that seems to me to originate in using uninitialized memory
when the channel structure here is used in the event code in
nl80211 later.
He never reported whether this fixed it, and I wasn't able
to trigger this so far, but we should do the right thing and
fully initialize the on-stack structure anyway.
Reported-by: Paul Menzel <pmenzel+linux-wireless@molgen.mpg.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
One thing is notable: I applied two patches and later
reverted them - we'll get back to that once all the driver
situation is sorted out.
-----BEGIN PGP SIGNATURE-----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=M0gz
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-01-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
We have things all over the place, no point listing them.
One thing is notable: I applied two patches and later
reverted them - we'll get back to that once all the driver
situation is sorted out.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
nl80211_nan_add_func() does not check if the required attribute
NL80211_NAN_FUNC_FOLLOW_UP_DEST is present when processing
NL80211_CMD_ADD_NAN_FUNCTION request. This request can be issued
by users with CAP_NET_ADMIN privilege and may result in NULL dereference
and a system crash. Add a check for the required attribute presence.
Signed-off-by: Hao Chen <flank3rsky@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit enhances the scan results to report the per chain signal
strength based on the latest BSS update. This provides similar
information to what is already available through STA information.
Signed-off-by: Sunil Dutt <usdutt@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Send disconnection reason code to user space even if it's locally
generated, since some tests that check reason code may fail because of
the current behavior.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Not only does this remove the need for the hexdump code in most
normal kernel builds (still there for the extra directory), but
it also removes the need to ship binary files, which apparently
is somewhat problematic, as Randy reported.
While at it, also add the generated files to clean-files.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the certs C code generation appends to the generated files,
which is most likely a leftover from commit 715a123347 ("wireless:
don't write C files on failures"). This causes duplicate code in the
generated files if the certificates have their timestamps modified
between builds and thereby trigger the generation rules.
Fixes: 715a123347 ("wireless: don't write C files on failures")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Evidently I introduced a locking bug in my change here,
the nla_put_failure sometimes needs to unlock. Fix it.
Fixes: 44905265bc ("nl80211: don't expose wdev->ssid for most interfaces")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Both cfg80211_rx_mgmt and cfg80211_report_obss_beacon functions send
reports to userspace using NL80211_ATTR_RX_SIGNAL_DBM attribute w/o
any processing of their input signal values. Which means that in
order to match userspace tools expectations, input signal values
for those functions are supposed to be in dBm units.
This patch cleans up comments, variable names, and trace reports
for those functions, replacing confusing 'mBm' by 'dBm'.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for drivers that implement static WEP internally for IBSS.
Add the WEP keys to the IBSS params struct, that will allow the driver
to use the keys in the join flow, and not only after the connection.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change the scripting inside the shipped/extra certs C code
generation to not write the file when there are any failures.
That way, if the build aborts due to failures, we don't get
into a situation where a dummy file has been created and the
next build succeeds, but not with the desired output.
Fixes: 90a53e4432 ("cfg80211: implement regdb signature checking")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since od/sed are in posix, hopefully there's a better chance
people will have them, over hexdump.
Fixes: 90a53e4432 ("cfg80211: implement regdb signature checking")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking fixes from David Miller:
1) The forcedeth conversion from pci_*() DMA interfaces to dma_*() ones
missed one spot. From Zhu Yanjun.
2) Missing CRYPTO_SHA256 Kconfig dep in cfg80211, from Johannes Berg.
3) Fix checksum offloading in thunderx driver, from Sunil Goutham.
4) Add SPDX to vm_sockets_diag.h, from Stephen Hemminger.
5) Fix use after free of packet headers in TIPC, from Jon Maloy.
6) "sizeof(ptr)" vs "sizeof(*ptr)" bug in i40e, from Gustavo A R Silva.
7) Tunneling fixes in mlxsw driver, from Petr Machata.
8) Fix crash in fanout_demux_rollover() of AF_PACKET, from Mike
Maloney.
9) Fix race in AF_PACKET bind() vs. NETDEV_UP notifier, from Eric
Dumazet.
10) Fix regression in sch_sfq.c due to one of the timer_setup()
conversions. From Paolo Abeni.
11) SCTP does list_for_each_entry() using wrong struct member, fix from
Xin Long.
12) Don't use big endian netlink attribute read for
IFLA_BOND_AD_ACTOR_SYSTEM, it is in cpu endianness. Also from Xin
Long.
13) Fix mis-initialization of q->link.clock in CBQ scheduler, preventing
adding filters there. From Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
ethernet: dwmac-stm32: Fix copyright
net: via: via-rhine: use %p to format void * address instead of %x
net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bit
myri10ge: Update MAINTAINERS
net: sched: cbq: create block for q->link.block
atm: suni: remove extraneous space to fix indentation
atm: lanai: use %p to format kernel addresses instead of %x
VSOCK: Don't set sk_state to TCP_CLOSE before testing it
atm: fore200e: use %pK to format kernel addresses instead of %x
ambassador: fix incorrect indentation of assignment statement
vxlan: use __be32 type for the param vni in __vxlan_fdb_delete
bonding: use nla_get_u64 to extract the value for IFLA_BOND_AD_ACTOR_SYSTEM
sctp: use right member as the param of list_for_each_entry
sch_sfq: fix null pointer dereference at timer expiration
cls_bpf: don't decrement net's refcount when offload fails
net/packet: fix a race in packet_bind() and packet_notifier()
packet: fix crash in fanout_demux_rollover()
sctp: remove extern from stream sched
sctp: force the params with right types for sctp csum apis
sctp: force SCTP_ERROR_INV_STRM with __u32 when calling sctp_chunk_fail
...
When regulatory database certificates are built-in, they're
currently using the SHA256 digest algorithm, so add that to
the build in that case.
Also add a note that for custom certificates, one may need
to add the right algorithms.
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When cfg80211 is built as a module, everything is fine, and we
can keep the code as is; in fact, we have to, because there can
only be a single module_init().
When cfg80211 is built-in, however, it needs to initialize
before drivers (device_initcall/module_init), and thus used to
be at subsys_initcall(). I'd moved it to fs_initcall() earlier,
where it can remain. However, this is still too early because at
that point the key infrastructure hasn't been initialized yet,
so X.509 certificates can't be parsed yet.
To work around this problem, load the regdb keys only later in
a late_initcall(), at which point the necessary infrastructure
has been initialized.
Fixes: 90a53e4432 ("cfg80211: implement regdb signature checking")
Reported-by: Xiaolong Ye <xiaolong.ye@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sara Sharon
Johannes Berg
Peng Xu
Liangwei Dong
Srinivas Dasari
Veerendranath Jakkam
Sriram R
Gustavo A. R. Silva
Chaitanya Tata
Chaitanya Tata
Julan Hsu
Toke Høiland-Jørgensen
Linus Torvalds
David S. Miller
Luca Coelho
Jouni Malinen
Eric Biggers
Bob Copeland
Andrew Zaborowski
Martin Willi
Sergey Matyukevich
Ankita Bajaj
Pradeep Kumar Chitrapu
Colin Ian King
zhong jiang
Yu Zhao
Stefan Seyfried
Masashi Honma
Stanislaw Gruszka
Andrei Otcheretianski
Shaul Triebitz
Dan Carpenter
Arunk Khandavalli
Balaji Pothunoori
Haim Dreyfuss
Alexei Avshalom Lazar
Rajeev Kumar Sirasanagandla
Dedy Lansky
Kees Cook
Amar Singhal
Bernd Edlinger
Denis Kenzior
Omer Efrat
Arnd Bergmann
Antonio Quartulli
Sven Eckelmann
Vidyullatha Kanchanapally
Arend Van Spriel
Arend van Spriel
Christoph Hellwig
weiyongjun (A)
Kirill Tkhai
Dmitry Lebed
Alexei Starovoitov
Joe Perches
Felix Fietkau
Romain Naour
Avraham Stern
Venkateswara Naralasetty
tamizhr@codeaurora.org
Srinivas Dasari
Sunil Dutt
Dan Williams
Al Viro
Alexey Dobriyan
Dominik Brodowski
Hao Chen
David Spinadel
Thierry Reding
Tova Mussai