Fix the port-lock initialisation regression introduced by commit
a3cb39d258 ("serial: core: Allow detach and attach serial device for
console") by making sure that the lock is again initialised during
console setup.
The console may be registered before the serial controller has been
probed in which case the port lock needs to be initialised during
console setup by a call to uart_set_options(). The console-detach
changes introduced a regression in several drivers by effectively
removing that initialisation by not initialising the lock when the port
is used as a console (which is always the case during console setup).
Add back the early lock initialisation and instead use a new
console-reinit flag to handle the case where a console is being
re-attached through sysfs.
The question whether the console-detach interface should have been added
in the first place is left for another discussion.
Note that the console-enabled check in uart_set_options() is not
redundant because of kgdboc, which can end up reinitialising an already
enabled console (see commit 42b6a1baa3 ("serial_core: Don't
re-initialize a previously initialized spinlock.")).
Fixes: a3cb39d258 ("serial: core: Allow detach and attach serial device for console")
Cc: stable <stable@vger.kernel.org> # 5.7
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200909143101.15389-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f743061a85 ("serial: core: Initialise spin lock before use in
uart_configure_port()") tried to work around a breakage introduced by
commit a3cb39d258 ("serial: core: Allow detach and attach serial
device for console") by adding a second initialisation of the port lock
when registering the port.
As reported by the build robots [1], this doesn't really solve the
regression introduced by the console-detach changes and also adds a
second redundant initialisation of the lock for normal ports.
Start cleaning up this mess by removing the redundant initialisation and
making sure that the port lock is again initialised once-only for ports
that aren't already in use as a console.
[1] https://lore.kernel.org/r/20200802054852.GR23458@shao2-debian
Fixes: f743061a85 ("serial: core: Initialise spin lock before use in uart_configure_port()")
Fixes: a3cb39d258 ("serial: core: Allow detach and attach serial device for console")
Cc: stable <stable@vger.kernel.org> # 5.7
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200909143101.15389-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are a few small TTY/Serial/vt fixes for 5.9-rc3
Included in here are:
- qcom serial fixes
- vt ioctl and core bugfixes
- pl011 serial driver fixes
- 8250 serial driver fixes
- other misc serial driver fixes
and for good measure:
- fbcon fix for syzbot found problem.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX0Zl1w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykh0wCgicGyVAq3OUH9iTlgYqdkFHL1FWoAnAtP/jot
dB0yRgk2r+RvDL9Odb2u
=x5GL
-----END PGP SIGNATURE-----
Merge tag 'tty-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are a few small TTY/Serial/vt fixes for 5.9-rc3
Included in here are:
- qcom serial fixes
- vt ioctl and core bugfixes
- pl011 serial driver fixes
- 8250 serial driver fixes
- other misc serial driver fixes
and for good measure:
- fbcon fix for syzbot found problem.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: imx: add dependence and build for earlycon
serial: samsung: Removes the IRQ not found warning
serial: 8250: change lock order in serial8250_do_startup()
serial: stm32: avoid kernel warning on absence of optional IRQ
serial: pl011: Fix oops on -EPROBE_DEFER
serial: pl011: Don't leak amba_ports entry on driver register error
serial: 8250_exar: Fix number of ports for Commtech PCIe cards
tty: serial: qcom_geni_serial: Drop __init from qcom_geni_console_setup
serial: qcom_geni_serial: Fix recent kdb hang
vt_ioctl: change VT_RESIZEX ioctl to check for error return from vc_resize()
fbcon: prevent user font height or width change from causing potential out-of-bounds access
vt: defer kfree() of vc_screenbuf in vc_do_resize()
In few older Samsung SoCs like s3c2410, s3c2412
and s3c2440, UART IP is having 2 interrupt lines.
However, in other SoCs like s3c6400, s5pv210,
exynos5433, and exynos4210 UART is having only 1
interrupt line. Due to this, "platform_get_irq(platdev, 1)"
call in the driver gives the following false-positive error:
"IRQ index 1 not found" on newer SoC's.
This patch adds the condition to check for Tx interrupt
only for the those SoC's which have 2 interrupt lines.
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Tamseel Shams <m.shams@samsung.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200810030021.45348-1-m.shams@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
stm32_init_port() of the stm32-usart may trigger a warning in
platform_get_irq() when the device tree specifies no wakeup interrupt.
The wakeup interrupt is usually a board-specific GPIO and the driver
functions correctly in its absence. The mainline stm32mp151.dtsi does
not specify it, so all mainline device trees trigger an unnecessary
kernel warning. Use of platform_get_irq_optional() avoids this.
Fixes: 2c58e56096 ("serial: stm32: fix the get_irq error case")
Signed-off-by: Holger Assmann <h.assmann@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200813152757.32751-1-h.assmann@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If probing of a pl011 gets deferred until after free_initmem(), an oops
ensues because pl011_console_match() is called which has been freed.
Fix by removing the __init attribute from the function and those it
calls.
Commit 10879ae5f1 ("serial: pl011: add console matching function")
introduced pl011_console_match() not just for early consoles but
regular preferred consoles, such as those added by acpi_parse_spcr().
Regular consoles may be registered after free_initmem() for various
reasons, one being deferred probing, another being dynamic enablement
of serial ports using a DeviceTree overlay.
Thus, pl011_console_match() must not be declared __init and the
functions it calls mustn't either.
Stack trace for posterity:
Unable to handle kernel paging request at virtual address 80c38b58
Internal error: Oops: 8000000d [#1] PREEMPT SMP ARM
PC is at pl011_console_match+0x0/0xfc
LR is at register_console+0x150/0x468
[<80187004>] (register_console)
[<805a8184>] (uart_add_one_port)
[<805b2b68>] (pl011_register_port)
[<805b3ce4>] (pl011_probe)
[<80569214>] (amba_probe)
[<805ca088>] (really_probe)
[<805ca2ec>] (driver_probe_device)
[<805ca5b0>] (__device_attach_driver)
[<805c8060>] (bus_for_each_drv)
[<805c9dfc>] (__device_attach)
[<805ca630>] (device_initial_probe)
[<805c90a8>] (bus_probe_device)
[<805c95a8>] (deferred_probe_work_func)
Fixes: 10879ae5f1 ("serial: pl011: add console matching function")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.10+
Cc: Aleksey Makarov <amakarov@marvell.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Christopher Covington <cov@codeaurora.org>
Link: https://lore.kernel.org/r/f827ff09da55b8c57d316a1b008a137677b58921.1597315557.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pl011_probe() calls pl011_setup_port() to reserve an amba_ports[] entry,
then calls pl011_register_port() to register the uart driver with the
tty layer.
If registration of the uart driver fails, the amba_ports[] entry is not
released. If this happens 14 times (value of UART_NR macro), then all
amba_ports[] entries will have been leaked and driver probing is no
longer possible. (To be fair, that can only happen if the DeviceTree
doesn't contain alias IDs since they cause the same entry to be used for
a given port.) Fix it.
Fixes: ef2889f7ff ("serial: pl011: Move uart_register_driver call to device")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.15+
Cc: Tushar Behera <tushar.behera@linaro.org>
Link: https://lore.kernel.org/r/138f8c15afb2f184d8102583f8301575566064a6.1597316167.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following in 8250_exar.c line 589 is used to determine the number
of ports for each Exar board:
nr_ports = board->num_ports ? board->num_ports : pcidev->device & 0x0f;
If the number of ports a card has is not explicitly specified, it defaults
to the rightmost 4 bits of the PCI device ID. This is prone to error since
not all PCI device IDs contain a number which corresponds to the number of
ports that card provides.
This particular case involves COMMTECH_4222PCIE, COMMTECH_4224PCIE and
COMMTECH_4228PCIE cards with device IDs 0x0022, 0x0020 and 0x0021.
Currently the multiport cards receive 2, 0 and 1 port instead of 2, 4 and
8 ports respectively.
To fix this, each Commtech Fastcom PCIe card is given a struct where the
number of ports is explicitly specified. This ensures 'board->num_ports'
is used instead of the default 'pcidev->device & 0x0f'.
Fixes: d0aeaa83f0 ("serial: exar: split out the exar code from 8250_pci")
Signed-off-by: Valmer Huhn <valmer.huhn@concurrent-rt.com>
Tested-by: Valmer Huhn <valmer.huhn@concurrent-rt.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200813165255.GC345440@icarus.concurrent-rt.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit e42d6c3ec0 ("serial: qcom_geni_serial: Make kgdb work
even if UART isn't console") worked pretty well and I've been doing a
lot of debugging with it. However, recently I typed "dmesg" in kdb
and then held the space key down to scroll through the pagination. My
device hung. This was repeatable and I found that it was introduced
with the aforementioned commit.
It turns out that there are some strange boundary cases in geni where
in some weird situations it will signal RX_LAST but then will put 0 in
RX_LAST_BYTE. This means that the entire last FIFO entry is valid.
This weird corner case is handled in qcom_geni_serial_handle_rx()
where you can see that we only honor RX_LAST_BYTE if RX_LAST is set
_and_ RX_LAST_BYTE is non-zero. If either of these is not true we use
BYTES_PER_FIFO_WORD (4) for the size of the last FIFO word.
Let's fix kgdb. While at it, also use the proper #define for 4.
Fixes: e42d6c3ec0 ("serial: qcom_geni_serial: Make kgdb work even if UART isn't console")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/20200806221904.1.I4455ff86f0ef5281c2a0cd0a4712db614548a5ca@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the large set of TTY and Serial driver patches for 5.9-rc1.
Lots of bugfixes in here, thanks to syzbot fuzzing for serial and vt and
console code.
Other highlights include:
- much needed vt/vc code cleanup from Jiri Slaby
- 8250 driver fixes and additions
- various serial driver updates and feature enhancements
- locking cleanup for serial/console initializations
- other minor cleanups
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXyv30A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynW+gCgv+OqxT0jeNRAMSQcpMvP3wTBMKIAn1StfjJ4
y8uwZuQQimD49uj8XtDq
=bKSv
-----END PGP SIGNATURE-----
Merge tag 'tty-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the large set of TTY and Serial driver patches for 5.9-rc1.
Lots of bugfixes in here, thanks to syzbot fuzzing for serial and vt
and console code.
Other highlights include:
- much needed vt/vc code cleanup from Jiri Slaby
- 8250 driver fixes and additions
- various serial driver updates and feature enhancements
- locking cleanup for serial/console initializations
- other minor cleanups
All of these have been in linux-next with no reported issues"
* tag 'tty-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (90 commits)
MAINTAINERS: enlist Greg formally for console stuff
vgacon: Fix for missing check in scrollback handling
Revert "serial: 8250: Let serial core initialise spin lock"
serial: 8250: Let serial core initialise spin lock
tty: keyboard, do not speculate on func_table index
serial: stm32: Add RS485 RTS GPIO control
serial: 8250_dw: Fix common clocks usage race condition
serial: 8250_dw: Pass the same rate to the clk round and set rate methods
serial: 8250_dw: Simplify the ref clock rate setting procedure
serial: 8250: Add 8250 port clock update method
tty: serial: imx: add imx earlycon driver
tty: serial: imx: enable imx serial console port as module
tty/synclink: remove leftover bits of non-PCI card support
tty: Use the preferred form for passing the size of a structure type
tty: Fix identation issues in struct serial_struct32
tty: Avoid the use of one-element arrays
serial: msm_serial: add sparse context annotation
serial: pmac_zilog: add sparse context annotation
newport_con: vc_color is now in state
serial: imx: use hrtimers for rs485 delays
...
static priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low' priority level,
plus sched_set_normal() to set the policy back to non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in a separate
tree.
When merging to the latest upstream tree there's a conflict in drivers/spi/spi.c,
which can be resolved via:
sched_set_fifo(ctlr->kworker_task);
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=/7JH
-----END PGP SIGNATURE-----
Merge tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull sched/fifo updates from Ingo Molnar:
"This adds the sched_set_fifo*() encapsulation APIs to remove static
priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low'
priority level, plus sched_set_normal() to set the policy back to
non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in
a separate tree"
* tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
sched,tracing: Convert to sched_set_fifo()
sched: Remove sched_set_*() return value
sched: Remove sched_setscheduler*() EXPORTs
sched,psi: Convert to sched_set_fifo_low()
sched,rcutorture: Convert to sched_set_fifo_low()
sched,rcuperf: Convert to sched_set_fifo_low()
sched,locktorture: Convert to sched_set_fifo()
sched,irq: Convert to sched_set_fifo()
sched,watchdog: Convert to sched_set_fifo()
sched,serial: Convert to sched_set_fifo()
sched,powerclamp: Convert to sched_set_fifo()
sched,ion: Convert to sched_set_normal()
sched,powercap: Convert to sched_set_fifo*()
sched,spi: Convert to sched_set_fifo*()
sched,mmc: Convert to sched_set_fifo*()
sched,ivtv: Convert to sched_set_fifo*()
sched,drm/scheduler: Convert to sched_set_fifo*()
sched,msm: Convert to sched_set_fifo*()
sched,psci: Convert to sched_set_fifo*()
sched,drbd: Convert to sched_set_fifo*()
...
-----BEGIN PGP SIGNATURE-----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=ZcMq
-----END PGP SIGNATURE-----
Merge tag 'printk-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Herbert Xu made printk header file self-contained.
- Andy Shevchenko and Sergey Senozhatsky cleaned up console->setup()
error handling.
- Andy Shevchenko did some cleanups (e.g. sparse warning) in vsprintf
code.
- Minor documentation updates.
* tag 'printk-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
lib/vsprintf: Force type of flags value for gfp_t
lib/vsprintf: Replace custom spec to print decimals with generic one
lib/vsprintf: Replace hidden BUILD_BUG_ON() with static_assert()
printk: Make linux/printk.h self-contained
doc:kmsg: explicitly state the return value in case of SEEK_CUR
Replace HTTP links with HTTPS ones: vsprintf
hvc: unify console setup naming
console: Fix trivia typo 'change' -> 'chance'
console: Propagate error code from console ->setup()
tty: hvc: Return proper error code from console ->setup() hook
serial: sunzilog: Return proper error code from console ->setup() hook
serial: sunsab: Return proper error code from console ->setup() hook
mips: Return proper error code from console ->setup() hook
A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory
subsystem and its drivers, starting out with a set of cleanup
patches.
A larger driver for the Tegra memory controller that was accidentally
missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware blobs
The tegra firmware driver gets extended to export some debug information
Various updates to i.MX firmware drivers, mostly cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space.
A new firmware based trusted platform module (fTPM) driver is added
based on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for identifying
a machine through the SMCCC ARCH_SOC_ID firmware interface rather than
by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device code.
There are also a number of updates to SoC specific drivers,
the main ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver
-----BEGIN PGP SIGNATURE-----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=nezz
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers
itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory subsystem
and its drivers, starting out with a set of cleanup patches.
A larger driver for the Tegra memory controller that was
accidentally missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware
blobs The tegra firmware driver gets extended to export some debug
information Various updates to i.MX firmware drivers, mostly
cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space. A new
firmware based trusted platform module (fTPM) driver is added based
on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for
identifying a machine through the SMCCC ARCH_SOC_ID firmware
interface rather than by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device
code.
There are also a number of updates to SoC specific drivers, the main
ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver"
* tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (164 commits)
soc: qcom: geni: Fix unused label warning
soc: qcom: smd-rpm: Fix kerneldoc
memory: jz4780_nemc: Only request IO memory the driver will use
soc: qcom: pdr: Reorder the PD state indication ack
MAINTAINERS: Add Git repository for memory controller drivers
memory: brcmstb_dpfe: Fix language typo
memory: samsung: exynos5422-dmc: Correct white space issues
memory: samsung: exynos-srom: Correct alignment
memory: pl172: Enclose macro argument usage in parenthesis
memory: of: Correct kerneldoc
memory: omap-gpmc: Fix language typo
memory: omap-gpmc: Correct white space issues
memory: omap-gpmc: Use 'unsigned int' for consistency
memory: omap-gpmc: Enclose macro argument usage in parenthesis
memory: omap-gpmc: Correct kerneldoc
memory: mvebu-devbus: Align with open parenthesis
memory: mvebu-devbus: Add missing braces to all arms of if statement
memory: bt1-l2-ctl: Add blank lines after declarations
soc: TI knav_qmss: make symbol 'knav_acc_range_ops' static
firmware: ti_sci: Replace HTTP links with HTTPS ones
...
This reverts commit 679193b7ba.
It appears that in QEmu the lock has been initialised differently
(it wasn't obvious on real hardware during testing). Let's
revert the change until the better approach will be developed.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200802111612.36189-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the serial core handles spin lock initialisation,
let the driver rely on it.
Depends-on: f743061a85 ("serial: core: Initialise spin lock before use in uart_configure_port()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200731123733.22754-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the STM32 does support RS485 drive-enable control within the
UART IP itself, some systems have the drive-enable line connected
to a pin which cannot be pinmuxed as RTS. Add support for toggling
the RTS GPIO line using the modem control GPIOs to provide at least
some sort of emulation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-stm32@st-md-mailman.stormreply.com
Link: https://lore.kernel.org/r/20200725144947.537007-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The race condition may happen if the UART reference clock is shared with
some other device (on Baikal-T1 SoC it's another DW UART port). In this
case if that device changes the clock rate while serial console is using
it the DW 8250 UART port might not only end up with an invalid uartclk
value saved, but may also experience a distorted output data since
baud-clock could have been changed. In order to fix this lets at least
try to adjust the 8250 port setting like UART clock rate in case if the
reference clock rate change is discovered. The driver will call the new
method to update 8250 UART port clock rate settings. It's done by means of
the clock event notifier registered at the port startup and unregistered
in the shutdown callback method.
Note 1. In order to avoid deadlocks we had to execute the UART port update
method in a dedicated deferred work. This is due to (in my opinion
redundant) the clock update implemented in the dw8250_set_termios()
method.
Note 2. Before the ref clock is manually changed by the custom
set_termios() function we swap the port uartclk value with new rate
adjusted to be suitable for the requested baud. It is necessary in
order to effectively disable a functionality of the ref clock events
handler for the current UART port, since uartclk update will be done
a bit further in the generic serial8250_do_set_termios() function.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200723003357.26897-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Indeed according to the clk API if clk_round_rate() has successfully
accepted a rate, then in order setup the clock with value returned by the
clk_round_rate() the clk_set_rate() method must be called with the
original rate value.
Suggested-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200723003357.26897-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Really instead of twice checking the clk_round_rate() return value
we could do it once, and if it isn't error the clock rate can be changed.
By doing so we decrease a number of ret-value tests and remove a weird
goto-based construction implemented in the dw8250_set_termios() method.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200723003357.26897-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some platforms can be designed in a way so the UART port reference clock
might be asynchronously changed at some point. In Baikal-T1 SoC this may
happen due to the reference clock being shared between two UART ports, on
the Allwinner SoC the reference clock is derived from the CPU clock, so
any CPU frequency change should get to be known/reflected by/in the UART
controller as well. But it's not enough to just update the
uart_port->uartclk field of the corresponding UART port, the 8250
controller reference clock divisor should be altered so to preserve
current baud rate setting. All of these things is done in a coherent
way by calling the serial8250_update_uartclk() method provided in this
patch. Though note that it isn't supposed to be called from within the
UART port callbacks because the locks using to the protect the UART port
data are already taken in there.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200723003357.26897-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split imx earlycon driver from imx serial driver "imx.c" as
separated driver. imx serial driver can be built as module,
but earlycon driver only support build in.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20200724070815.11445-3-fugang.duan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for building i.MX serial driver as module.
The changes of the patch:
- imx console driver can be built as module.
- move out earlycon code to separated driver like imx_earlycon.c,
and imx earlycon driver only support build-in.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20200724070815.11445-2-fugang.duan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl8d8h4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGd0sH/2iktYhMwPxzzpnb
eI3OuTX/mRn4vUFOfpx9dmGVleMfKkpbvnn3IY7wA62Qfv7J7lkFRa1Bd1DlqXfW
yyGTGDSKG5chiRCOU3s9ni92M4xIzFlrojyt/dIK2lUGMzUPI9FGlZRGQLKqqwLh
2syOXRWbcQ7e52IHtDSy3YBNveKRsP4NyqV+GxGiex18SMB/M3Pw9EMH614eDPsE
QAGQi5uGv4hPJtFHgXgUyBPLFHIyFAiVxhFRIj7u2DSEKY79+wO1CGWFiFvdTY4B
CbqKXLffY3iQdFsLJkj9Dl8cnOQnoY44V0EBzhhORxeOp71StUVaRwQMFa5tp48G
171s5Hs=
=BQIl
-----END PGP SIGNATURE-----
Merge 5.8-rc7 into tty-next
we need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sealevel XR17V35X based devices are inoperable on kernel versions
4.11 and above due to a change in the GPIO preconfiguration introduced in
commit
7dea8165f1. This patch fixes this by preconfiguring the GPIO on Sealevel
cards to the value (0x00) used prior to commit 7dea8165f1
With GPIOs preconfigured as per commit 7dea8165f1 all ports on
Sealevel XR17V35X based devices become stuck in high impedance
mode, regardless of dip-switch or software configuration. This
causes the device to become effectively unusable. This patch (in
various forms) has been distributed to our customers and no issues
related to it have been reported.
Fixes: 7dea8165f1 ("serial: exar: Preconfigure xr17v35x MPIOs as output")
Signed-off-by: Matthew Howell <matthew.howell@sealevel.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2007221605270.13247@tstest-VirtualBox
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add sparse context annotation to the receive handlers, which release and
reacquire the port lock, to silence sparse warnings:
drivers/tty/serial/msm_serial.c:748:25: warning: context imbalance in 'msm_handle_rx_dm' - unexpected unlock
drivers/tty/serial/msm_serial.c:814:28: warning: context imbalance in 'msm_handle_rx' - unexpected unlock
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200723123327.5843-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add sparse context annotation to the receive handler, which releases and
reacquires the port lock, to silence a sparse warning:
drivers/tty/serial/pmac_zilog.c:255:36: sparse: sparse: context imbalance in 'pmz_receive_chars' - unexpected unlock
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200723123327.5843-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7b668c064e ("serial: 8250: Fix max baud limit in generic 8250
port") fixed limits of a baud rate setting for a generic 8250 port.
In other words since that commit the baud rate has been permitted to be
within [uartclk / 16 / UART_DIV_MAX; uartclk / 16], which is absolutely
normal for a standard 8250 UART port. But there are custom 8250 ports,
which provide extended baud rate limits. In particular the Mediatek 8250
port can work with baud rates up to "uartclk" speed.
Normally that and any other peculiarity is supposed to be handled in a
custom set_termios() callback implemented in the vendor-specific
8250-port glue-driver. Currently that is how it's done for the most of
the vendor-specific 8250 ports, but for some reason for Mediatek a
solution has been spread out to both the glue-driver and to the generic
8250-port code. Due to that a bug has been introduced, which permitted the
extended baud rate limit for all even for standard 8250-ports. The bug
has been fixed by the commit 7b668c064e ("serial: 8250: Fix max baud
limit in generic 8250 port") by narrowing the baud rates limit back down to
the normal bounds. Unfortunately by doing so we also broke the
Mediatek-specific extended bauds feature.
A fix of the problem described above is twofold. First since we can't get
back the extended baud rate limits feature to the generic set_termios()
function and that method supports only a standard baud rates range, the
requested baud rate must be locally stored before calling it and then
restored back to the new termios structure after the generic set_termios()
finished its magic business. By doing so we still use the
serial8250_do_set_termios() method to set the LCR/MCR/FCR/etc. registers,
while the extended baud rate setting procedure will be performed later in
the custom Mediatek-specific set_termios() callback. Second since a true
baud rate is now fully calculated in the custom set_termios() method we
need to locally update the port timeout by calling the
uart_update_timeout() function. After the fixes described above are
implemented in the 8250_mtk.c driver, the Mediatek 8250-port should
get back to normally working with extended baud rates.
Link: https://lore.kernel.org/linux-serial/20200701211337.3027448-1-danielwinkler@google.com
Fixes: 7b668c064e ("serial: 8250: Fix max baud limit in generic 8250 port")
Reported-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: stable <stable@vger.kernel.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Link: https://lore.kernel.org/r/20200714124113.20918-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch imitates 6e0a5de213 ("serial: 8250: Use hrtimers for
rs485 delays") in replacing the previously used classic timers
with hrtimers. The old way provided a too coarse resolution on
systems with configs of less than 1000 HZ.
Use of hrtimers addresses this and can be easily extended to
support microsecond resolution in future when support
for this arrives upstream.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20200714093012.21621-3-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support for delays between assertion of RTS (which is supposed
to enable the rs485 transmitter) and sending as well as between the last
send char and deassertionof RTS.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20200714093012.21621-2-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct tty_port is part of the uart state and will never be NULL in
the receive helpers. Drop the bogus NULL checks and rename the
pointer-variables "port" to differentiate them from struct tty_struct
pointers (which can be NULL).
Fixes: 962963e4ee ("serial: tegra: Switch to using struct tty_port")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200710135947.2737-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 33ae787b74 ("serial: tegra: add support to ignore read") added
support for dropping input in case CREAD isn't set, but for PIO the
ignore_status_mask wasn't checked until after the character had been
put in the receive buffer.
Note that the NULL tty-port test is bogus and will be removed by a
follow-on patch.
Fixes: 33ae787b74 ("serial: tegra: add support to ignore read")
Cc: stable <stable@vger.kernel.org> # 5.4
Cc: Shardar Shariff Md <smohammed@nvidia.com>
Cc: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200710135947.2737-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers using legacy PM have to manage PCI states and device's PM states
themselves. They also need to take care of configuration registers.
With improved and powerful support of generic PM, PCI Core takes care of
above mentioned, device-independent, jobs.
This driver makes use of PCI helper functions like
pci_save/restore_state(), pci_enable_device() and pci_set_power_state()
to do required operations. In generic mode, they are no longer needed.
Change function parameter in both .suspend() and .resume() to
"struct device*" type. Use dev_get_drvdata() to get drv data.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Link: https://lore.kernel.org/r/20200720120414.399961-1-vaibhavgupta40@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Link: https://lore.kernel.org/r/20200718103018.3164-1-grandmaster@al2klimov.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch error and warning:
1. space required after ','
2. Missing a blank line after declarations
Signed-off-by: Tamseel Shams <m.shams@samsung.com>
Link: https://lore.kernel.org/r/20200716115438.9967-1-m.shams@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200718100807.983-1-grandmaster@al2klimov.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200718123840.19957-1-grandmaster@al2klimov.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f38278e9b8.
There has been a quick fix against uninitialised lock revealed by
the commit f743061a85 ("serial: core: Initialise spin lock before use
in uart_configure_port()"). Since we have now better fix in serial core,
this may be safely reverted.
Fixes: f38278e9b8 ("serial: sh-sci: Initialize spinlock for uart console")
Depends-on: f743061a85 ("serial: core: Initialise spin lock before use in uart_configure_port()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200711135346.71171-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 8f065acec7.
There has been a quick fix against uninitialised lock revealed by
the commit f743061a85 ("serial: core: Initialise spin lock before use
in uart_configure_port()"). Since we have now better fix in serial core,
this may be safely reverted.
Fixes: 8f065acec7 ("serial: imx: Initialize lock for non-registered console")
Depends-on: f743061a85 ("serial: core: Initialise spin lock before use in uart_configure_port()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200711135346.71171-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 17b4efdf4e.
There has been a quick fix against uninitialised lock revealed by
the commit f743061a85 ("serial: core: Initialise spin lock before use
in uart_configure_port()"). Since we have now better fix in serial core,
this may be safely reverted.
Fixes: 17b4efdf4e ("tty: serial: add missing spin_lock_init for SiFive serial console")
Depends-on: f743061a85 ("serial: core: Initialise spin lock before use in uart_configure_port()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200711135346.71171-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 8508f4cba3.
There has been a quick fix against uninitialised lock revealed by
the commit f743061a85 ("serial: core: Initialise spin lock before use
in uart_configure_port()"). Since we have now better fix in serial core,
this may be safely reverted.
Fixes: 8508f4cba3 ("serial: amba-pl011: Make sure we initialize the port.lock spinlock")
Depends-on: f743061a85 ("serial: core: Initialise spin lock before use in uart_configure_port()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200711135346.71171-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 0f87aa66e8.
There has been a quick fix against uninitialised lock revealed by
the commit f743061a85 ("serial: core: Initialise spin lock before use
in uart_configure_port()"). Since we have now better fix in serial core,
this may be safely reverted.
Fixes: 0f87aa66e8 ("serial: sunhv: Initialize lock for non-registered console")
Depends-on: f743061a85 ("serial: core: Initialise spin lock before use in uart_configure_port()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200711135346.71171-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problems started with the revert (18cc7ac8a2). The
cdns_uart_console.index is statically assigned -1. When the port is
registered, Linux assigns consecutive numbers to it. It turned out that
when using ttyPS1 as console, the index is not updated as we are reusing
the same cdns_uart_console instance for multiple ports. When registering
ttyPS0, it gets updated from -1 to 0, but when registering ttyPS1, it
already is 0 and not updated.
That led to 2ae11c46d5. It assigns the index prior to registering
the uart_driver once. Unfortunately, that ended up breaking the
situation where the probe order does not match the id order. When using
the same device tree for both uboot and linux, it is important that the
serial0 alias points to the console. So some boards reverse those
aliases. This was reported by Jan Kiszka. The proposed fix was reverting
the index assignment and going back to the previous iteration.
However such a reversed assignement (serial0 -> uart1, serial1 -> uart0)
was already partially broken by the revert (18cc7ac8a2). While the
ttyPS device works, the kmsg connection is already broken and kernel
messages go missing. Reverting the id assignment does not fix this.
>From the xilinx_uartps driver pov (after reverting the refactoring
commits), there can be only one console. This manifests in static
variables console_pprt and cdns_uart_console. These variables are not
properly linked and can go out of sync. The cdns_uart_console.index is
important for uart_add_one_port. We call that function for each port -
one of which hopefully is the console. If it isn't, the CON_ENABLED flag
is not set and console_port is cleared. The next cdns_uart_probe call
then tries to register the next port using that same cdns_uart_console.
It is important that console_port and cdns_uart_console (and its index
in particular) stay in sync. The index assignment implemented by
Shubhrajyoti Datta is correct in principle. It just may have to happen a
second time if the first cdns_uart_probe call didn't encounter the
console device. And we shouldn't change the index once the console uart
is registered.
Reported-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Link: https://lore.kernel.org/linux-serial/f4092727-d8f5-5f91-2c9f-76643aace993@siemens.com/
Fixes: 18cc7ac8a2 ("Revert "serial: uartps: Register own uart console and driver structures"")
Fixes: 2ae11c46d5 ("tty: xilinx_uartps: Fix missing id assignment to the console")
Fixes: 76ed2e1057 ("Revert "tty: xilinx_uartps: Fix missing id assignment to the console"")
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200713073227.GA3805@laureti-dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl8UzA4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGQ7cH/3v+Gv+SmHJCvaT2
CSu0+7okVnYbY3UTb3hykk7/aOqb6284KjxR03r0CWFzsEsZVhC5pvvruASSiMQg
Pi04sLqv6CsGLHd1n+pl4AUYEaxq6k4KS3uU3HHSWxrahDDApQoRUx2F8lpOxyj8
RiwnoO60IMPA7IFJqzcZuFqsgdxqiiYvnzT461KX8Mrw6fyMXeR2KAj2NwMX8dZN
At21Sf8+LSoh6q2HnugfiUd/jR10XbfxIIx2lXgIinb15GXgWydEQVrDJ7cUV7ix
Jd0S+dtOtp+lWtFHDoyjjqqsMV7+G8i/rFNZoxSkyZqsUTaKzaR6JD3moSyoYZgG
0+eXO4A=
=9EpR
-----END PGP SIGNATURE-----
Merge 5.8-rc6 into tty-next
We need the serial/tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small tty and serial driver fixes for 5.8-rc6.
The largest set of patches in here is a revert of the sysrq changes that
went into 5.8-rc1 but turned out to cause a noticable overhead and cpu
usage.
Other than that, there's a few small serial driver fixes to resolve
reported issues, and finally resolving the spinlock init problem on many
serial driver consoles.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXxBx8g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykqAwCeIWhRt4Z6YdUXjT/rFycYlFKWCVsAoJodlx6C
7FoXKFoP4c72il+qgHMp
=cCbW
-----END PGP SIGNATURE-----
Merge tag 'tty-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty into master
Pull tty/serial driver fixes from Greg KH:
:Here are some small tty and serial driver fixes for 5.8-rc6.
The largest set of patches in here is a revert of the sysrq changes
that went into 5.8-rc1 but turned out to cause a noticable overhead
and cpu usage.
Other than that, there's a few small serial driver fixes to resolve
reported issues, and finally resolving the spinlock init problem on
many serial driver consoles.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: core: Initialise spin lock before use in uart_configure_port()
serial: mxs-auart: add missed iounmap() in probe failure and remove
serial: sh-sci: Initialize spinlock for uart console
Revert "tty: xilinx_uartps: Fix missing id assignment to the console"
serial: core: drop redundant sysrq checks
serial: core: fix sysrq overhead regression
Revert "serial: core: Refactor uart_unlock_and_check_sysrq()"
tty/serial: fix serial_core.c kernel-doc warnings
tty: serial: cpm_uart: Fix behaviour for non existing GPIOs
Tobias Diedrich
Johan Hovold
Linus Torvalds
Gustavo A. R. Silva
Fugang Duan
Tamseel Shams
Sergey Senozhatsky
Holger Assmann
Lukas Wunner
Valmer Huhn
John Stultz
Douglas Anderson
Andy Shevchenko
Marek Vasut
Serge Semin
Greg Kroah-Hartman
Matthew Howell
Yang Yingliang
Ahmad Fatoum
Uwe Kleine-König
Vaibhav Gupta
Alexander A. Klimov
Helmut Grohne