This patch adds support for "ns16850" as supported value
of the compatible node in flat device tree uart descriptions.
This is needed for example when you have a XR16C2850 uart
connected to a PPC405's external bus controller.
Signed-off-by: Matthias Fuchs <mfuchs@ma-fu.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix the following problem, related to hardware flow control (CTS/RTS):
Transmitting while CTS line is asserted in DMA mode, due to not checking
for tx-stopped condition.
We found these problems while testing the UARTs with hardware
flow-control.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: "Andrew Victor" <avictor.za@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This was not implemented correctly for the pnx8xxx_uart driver.
[From further discussion:
Correct, you can look to it as two separate bugs:
a) the next character is not ignored while it should;
b) the status bits 31-8 are copied to the 'ch' variable while they shouldn't.
Both bugs prevent correct break signal handling (and therefore correct
behaviour of the magic SysRq key). Bug b didn't cause too much trouble
earlier because in most situations the status bits are all zero; for
this case they unfortunately aren't.
]
Signed-off-by: Mischa Jonker <mischa.jonker@nxp.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add SupraExpress 336i PnP Voice Modem
Tested and working with the following device: (output from lspnp -v)
01:01.00 SUP1381 (unknown)
state = active
io 0x2f8-0x2ff
irq 3
Signed-off-by: Daniel Gagnon <daniel.gagnon@yahoo.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most of netmos 9835 hardware is handled by parport-serial. IBM introduces
a device which doesn't have any parallel ports and have screwed subdevice
PCI id (not corresponding to port numbers).
Handle this device (9710:9835 1014:0299) properly.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit b430428a18 ("8250: Don't clobber
spinlocks.") introduced a regression on the parisc architecture, which
broke the handover to the serial port at boottime.
early_serial_setup() was changed to only copy a subset of the uart_port
fields, and sadly the "type" and "line" fields were forgotten and thus
the serial port was not initialized and could not be used for a
handover. This patch fixes this by copying the missing fields.
As this change to early_serial_setup() doesn't need an initialized
spinlock in the uart_port struct any longer, we can drop the spinlock
initialization in the superio driver.
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Julia Lawall found an un-needed check in the neo driver. Her patch moves
the check to cover the code dereferencing it, however it cannot be NULL
anyway so remove the NULL check instead.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Always set CONFIG_SERIAL_SAMSUNG_UARTS when building any
of the S3C platforms as even if the driver is not selected
there it is still the facility for the machine files to
register configuration data for the possibility of the
driver being built.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for the nwp serial device which is connected to a DCR bus. It
uses the of_serial device driver to determine necessary properties from
the device tree. The supported device is added as serial port number 85.
NWP stands for network processor and it is part of the QPACE - Quantum
Chromodynamics Parallel Computing on the Cell Broadband Engine project.
The implementation is a lightweight uart implementation with the focus
to consume as little resources as possible and it is connected to a
DCR bus.
Signed-off-by: Benjamin Krill <ben@codiert.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
Commit d87a6d9 ("drivers/serial/: remove CVS keywords") removed one
space too many in the printk in serial8250_init(). Put it back in (and
add a comma for clarity).
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for Sealevel Systems Model 7803 COMM+8
Signed-off-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cavium UART implementation is not covered by existing uart_configS.
Define a new uart_config (PORT_OCTEON) which is specified by OCTEON
platform device registration code.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add flag value UPF_FIXED_TYPE which specifies that the UART type is
known and should not be probed. For this case the UARTs properties
are just copied out of the uart_config entry.
This allows us to keep SOC specific 8250 probe code out of 8250.c. In
this case we know the serial hardware will not be changing as it is on
the same silicon as the CPU, and we can specify it with certainty in
the board/cpu setup code.
The alternative is to load up 8250.c with a bunch of OCTEON specific
special cases in the probing code.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to use Cavium OCTEON specific serial i/o drivers, we first
patch the 8250 driver to use replaceable I/O functions. Compatible
I/O functions are added for existing iotypeS.
An added benefit of this change is that it makes it easy to factor
some of the existing special cases out to board/SOC specific support
code.
The alternative is to load up 8250.c with a bunch of OCTEON specific
iotype code and bug work-arounds.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In serial8250_isa_init_ports(), the port's lock is initialized. We
should not overwrite it. In early_serial_setup(), only copy in the
fields we need. Since the early console code only uses a subset of
the fields, these are sufficient.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the tty_port and uart_info bits around a little. By embedding the uart_info
into the uart_port we get rid of lots of corner case testing and also get the
ability to go port<->state<->info which is a bit more elegant than the current
data structures.
Downsides - we allocate a tiny bit more memory for unused ports, upside we've
removed as much code as it saved for most users..
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PCI-card identified as "Oxford Semiconductor Ltd EXSYS EX-41092 Dual
16950 Serial adapter" is only usable with other devices (i.e. not the same
card) after doing a "setserial /dev/ttyS<n> baud_base 115200". This
baud_base should be default for this card.
Signed-off-by: Niels de Vos <niels.devos@wincor-nixdorf.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
this happening again by making use of 'const'.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
scribble on its own reference structures.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add spin_lock_irqsave() when receive and transfer data.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bug description:
The IRDA receiver may can't receiving any more after processed some signals.
To duplicate this issue is put three IRDA devices together, one blackfin,
two none blackfin, they will detect each other. Let one none blackfin devices
irdaping the blackfin devices, when it stopped print out ping information,
it is the time that blackfin stoped receiving, the time is random.
The related register bit is OK, the other devices is sending data continuously.
But no interrupt come.
Fixing:
I tried Michael's suggestion that request the UARTx error interrupt, and reset
the IRDA when found FE error. This method helps much, but it can't completely
avoid stop.
Reset the IRDA before every time sending the data is more safe.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (407 commits)
[ARM] pxafb: add support for overlay1 and overlay2 as framebuffer devices
[ARM] pxafb: cleanup of the timing checking code
[ARM] pxafb: cleanup of the color format manipulation code
[ARM] pxafb: add palette format support for LCCR4_PAL_FOR_3
[ARM] pxafb: add support for FBIOPAN_DISPLAY by dma braching
[ARM] pxafb: allow pxafb_set_par() to start from arbitrary yoffset
[ARM] pxafb: allow video memory size to be configurable
[ARM] pxa: add document on the MFP design and how to use it
[ARM] sa1100_wdt: don't assume CLOCK_TICK_RATE to be a constant
[ARM] rtc-sa1100: don't assume CLOCK_TICK_RATE to be a constant
[ARM] pxa/tavorevb: update board support (smartpanel LCD + keypad)
[ARM] pxa: Update eseries defconfig
[ARM] 5352/1: add w90p910-plat config file
[ARM] s3c: S3C options should depend on PLAT_S3C
[ARM] mv78xx0: implement GPIO and GPIO interrupt support
[ARM] Kirkwood: implement GPIO and GPIO interrupt support
[ARM] Orion: share GPIO IRQ handling code
[ARM] Orion: share GPIO handling code
[ARM] s3c: define __io using the typesafe version
[ARM] S3C64XX: Ensure CPU_V6 is selected
...
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (144 commits)
powerpc/44x: Support 16K/64K base page sizes on 44x
powerpc: Force memory size to be a multiple of PAGE_SIZE
powerpc/32: Wire up the trampoline code for kdump
powerpc/32: Add the ability for a classic ppc kernel to be loaded at 32M
powerpc/32: Allow __ioremap on RAM addresses for kdump kernel
powerpc/32: Setup OF properties for kdump
powerpc/32/kdump: Implement crash_setup_regs() using ppc_save_regs()
powerpc: Prepare xmon_save_regs for use with kdump
powerpc: Remove default kexec/crash_kernel ops assignments
powerpc: Make default kexec/crash_kernel ops implicit
powerpc: Setup OF properties for ppc32 kexec
powerpc/pseries: Fix cpu hotplug
powerpc: Fix KVM build on ppc440
powerpc/cell: add QPACE as a separate Cell platform
powerpc/cell: fix build breakage with CONFIG_SPUFS disabled
powerpc/mpc5200: fix error paths in PSC UART probe function
powerpc/mpc5200: add rts/cts handling in PSC UART driver
powerpc/mpc5200: Make PSC UART driver update serial errors counters
powerpc/mpc5200: Remove obsolete code from mpc5200 MDIO driver
powerpc/mpc5200: Add MDMA/UDMA support to MPC5200 ATA driver
...
Fix trivial conflict in drivers/char/Makefile as per Paul's directions
sci_poll_put_char() happens to also be used by the serial console,
while sci_poll_get_char() is only used by CONFIG_CONSOLE_POLL. Add
another gnarly ifdef to shut up the compiler.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the SH-2A FPU based SH7201 processor subtype.
Signed-off-by: Peter Griffin <pgriffin@mpc-data.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
- error cases for mapbase and irq were unbundled
- mapped irq now gets disposed on error
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add RTS/CTS-support for the PSC of the MPC5200B. Tested with a Phytec
MPC5200B-IO.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds the capability to the mpc52xx-uart to report framing
errors, parity errors, breaks and overruns to userspace. These values
may be requested in userspace by using the ioctl TIOCGICOUNT.
Signed-off-by: René Bürgel <r.buergel@unicontrol.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
As noted by Russell King, do not print any warnings if the
uinfo or tty fields are not set when a CPU frequency change
is sent.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the usage of CONFIG_SERIAL_SAMSUNG_UARTS in several places
in the kernel where it had been missed. This finishes fixing a
long standing issue where S3C2443 and S3C64XX could not use the
4th UART
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch removes the inclusion of mach/hardware.h from mach/irqs.h and
switches to more meaningful names for the irq related macros.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Matthias Fuchs
Itai Levi
Mischa Jonker
Daniel Gagnon
Jiri Slaby
Helge Deller
Alan Cox
Linus Torvalds
Ben Dooks
Benjamin Krill
Kay Sievers
Paul Bolle
Frederik Schwarzer
Flavio Leitner
David Daney
Alexander Beregalov
Harvey Harrison
Niels de Vos
Russell King
Sonic Zhang
Graf Yang
Paul Mundt
Peter Griffin
Michael Trimarchi
Wolfram Sang
René Bürgel
Russell King
Sascha Hauer