The adv7180 produces 1 to 2 frames of garbage before proper sync is
established. This allows V4L2 drivers and apps to skip those.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CSI-2 bus may use either D-PHY or C-PHY. Make this visible in media
bus enum.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ADV7180 and ADV7182 transmit whole fields, bottom field followed
by top (or vice-versa, depending on detected video standard). So
for chips that do not have support for explicitly setting the field
mode via I2P, set the field mode to V4L2_FIELD_ALTERNATE.
I2P converts fields into frames using an edge adaptive algorithm. The
frame rate is the same as the 'field rate': e.g. X fields per second
are now X frames per second.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The entity function was ORed with the flags field instead of
assigned to the function field. Correct this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since i2c_unregister_device() became NULL-aware we may remove duplicate checks.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_i2c_subdev_init() sets V4L2_SUBDEV_FL_IS_I2C flag in the
subdev->flags. But this driver overwrites subdev->flags immediately after
calling v4l2_i2c_subdev_init(). So V4L2_SUBDEV_FL_IS_I2C is not set after
all.
This stops breaking subdev->flags and preserves V4L2_SUBDEV_FL_IS_I2C.
Side note: According to the comment in v4l2_device_unregister(), this is
problematic only if the device is platform bus device. Device tree or
ACPI based devices are not affected.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Used to differentiate between models with 3 and 6 inputs.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Drop the FSF's postal address from the source code files that typically
contain mostly the license text. Of the 628 removed instances, 578 are
outdated.
The patch has been created with the following command without manual edits:
git grep -l "675 Mass Ave\|59 Temple Place\|51 Franklin St" -- \
drivers/media/ include/media|while read i; do i=$i perl -e '
open(F,"< $ENV{i}");
$a=join("", <F>);
$a =~ s/[ \t]*\*\n.*You should.*\n.*along with.*\n.*(\n.*USA.*$)?\n//m
&& $a =~ s/(^.*)Or, (point your browser to) /$1To obtain the license, $2\n$1/m;
close(F);
open(F, "> $ENV{i}");
print F $a;
close(F);'; done
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
If the V4L2_SUBDEV_FORMAT_TRY is used in set_fmt the width, height etc
would not be filled.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The media bus format reported by the adv7180 is wrong. Steve Longerbeam
posted a patch which changed the format to UYVY8_2X8 with the commit
message:
Change the media bus format from YUYV8_2X8 to UYVY8_2X8. Colors
now look correct when capturing with the i.mx6 backend. The other
option is to set the SWPC bit in register 0x27 to swap the Cr and Cb
output samples.
The rcar-vin driver was developed and tested with the adv7180 and
therefor suffers from the same issue, looking for the wrong media bus
format. The two errors corrected each other.
This patch takes Steve's patch and merge it with a fix for rcar-vin
driver. The rcar-vin driver is used used in together with the adv7180
och Koelsch and this ensures it will not break while fixing the adv7180
issue. I checked wit Steve and he was fine with me merging the patches.
ADV7180 parts:
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Suggested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The old cropcap video op is now only used to pass the pixelaspect
ratio, so rename it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some targets control the ADV7180 power pin via a gpio, so add
optional support for "powerdown" pin control.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Access to the interrupt page registers has been broken since at least
commit 3999e5d01d ("[media] adv7180: Do implicit register paging").
That commit forgot to add the interrupt page number to the register
defines.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add entries for all supported chip variants into the of_match list, so that
the matching driver_info can be selected when using dt.
Signed-off-by: Julian Scheel <julian@jusst.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The adv7180 attempts to autodetect the standard. Unfortunately this
is seriously broken.
This patch removes the autodetect completely. Only the querystd op
will detect the standard. Since the design of the adv7180 requires
that you switch to a special autodetect mode you cannot call querystd
when you are streaming.
So the s_stream op has been added so we know whether we are streaming
or not, and if we are, then querystd returns EBUSY.
After testing this with a signal generator is became obvious that
a sleep is needed between changing the standard to autodetect and
reading the status. So the autodetect can never have worked well.
The s_std call now just sets the new standard without any querying.
If the driver supports the interrupt, then when it detects a standard
change it will signal that by sending the V4L2_EVENT_SOURCE_CHANGE
event.
With these changes this driver now behaves like all other video
receivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The ADV7180 supports NTSC, PAL and SECAM.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support to get the pixel aspect ratio depending on the current
standard (50 vs 60 Hz).
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support to get the standard to the adv7180 driver.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
With the MC next gen rework, what's left for media_entity_init()
is to just initialize the PADs. However, certain devices, like
a FLASH led/light doesn't have any input or output PAD.
So, there's no reason why calling media_entity_init() would be
mandatory. Also, despite its name, what this function actually
does is to initialize the PADs data. So, rename it to
media_entity_pads_init() in order to reflect that.
The media entity actual init happens during entity register,
at media_device_register_entity(). We should move init of
num_links and num_backlinks to it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently, media_entity_init() creates an array with the links,
allocated at init time. It provides a parameter (extra_links)
that would allocate more links than the current needs, but this
is not used by any driver.
As we want to be able to do dynamic link allocation/removal,
we'll need to change the implementation of the links. So,
before doing that, let's first remove that extra unused
parameter, in order to cleanup the interface first.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Initialization of the ADV7180 chip fails on the Renesas R8A7790-based
Lager board about 50% of the time. This patch resolves the issue by
increasing the minimum delay after reset from 2 ms to 5 ms, following the
recommendation in the ADV7180 datasheet:
"Executing a software reset takes approximately 2 ms. However, it is
recommended to wait 5 ms before any further I2C writes are performed."
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a proper of match id for use when the device is being bound via
device tree, to avoid having to use the i2c old-style binding of the
device.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: William.Towle <william.towle@codethink.co.uk>
Reviewed-by: Rob Taylor <rob.taylor@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If a subdevice pad op is called from a bridge driver, then there is
no v4l2_subdev_fh struct that can be passed to the subdevice. This
made it hard to use such subdevs from a bridge driver.
This patch replaces the v4l2_subdev_fh pointer by a v4l2_subdev_pad_config
pointer in the pad ops. This allows bridge drivers to use the various
try_ pad ops by creating a v4l2_subdev_pad_config struct and passing it
along to the pad op.
The v4l2_subdev_get_try_* macros had to be changed because of this, so
I also took the opportunity to use the full name of the v4l2_subdev_get_try_*
functions in the __V4L2_SUBDEV_MK_GET_TRY macro arguments: if you now do
'git grep v4l2_subdev_get_try_format' you will actually find the header
where it is defined.
One remark regarding the drivers/staging/media/davinci_vpfe patches: the
*_init_formats() functions assumed that fh could be NULL. However, that's
not true for this driver, it's always set. This is almost certainly a copy
and paste from the omap3isp driver. I've updated the code to reflect the
fact that fh is never NULL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In fast switch mode the adv7180 (and similar) can lock onto a new signal
faster when switching between different inputs. As a downside though it is
no longer able to auto-detect the incoming format.
The fast switch mode is exposed as a boolean v4l control that allows
userspace applications to either enable or disable fast switch mode.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some of the devices supported by this driver have a interlaced-to-
progressive converter which can optionally be enabled. This patch adds
support for enabling and disabling the I2P converter on such devices.
I2P mode can be enabled by selecting V4L2_FIELD_NONE instead of
V4L2_FIELD_INTERLACED for the format.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for the adv7280-m/adv2781-m/adv7281-ma/adv7282-m
devices to the adv7180 driver. They are very similar to the
adv7280/adv7281/adv7282 but instead of parallel video out they feature a
MIPI CSI2 transmitter.
The CSI2 transmitter is configured via a separate I2C address, so we need to
register a dummy device for it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for the adv7280/adv7281/adv7282 devices to the
adv7180 driver. They are very similar to the adv7182, the main difference
from the drivers point of view are some different tuning constants for
improved video performance.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for the adv7182 to the adv7180 driver. The adv7182
is similar to the adv7180, the main difference from the driver's point of
view is how the video input and how the input format are selected.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The adv7180 is part of a larger family of device, which have all a very
similar register map layout. This patch prepares the adv7180 driver for
support for multiple different devices. For now the only difference we care
about is the number of input channel configurations. Also the way the input
format is configured slightly differs between some devices.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We have basically the same code to set the video standard in init_device()
and adv7180_s_std(). Factor this out into a common helper function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add media controller support to the adv7180 driver by registering a media
entity instance for it as well as implementing pad ops for configuring the
format.
As there currently don't seem to be any users of the video ops format
operations those are removed as well in this patch.
Also set the V4L2_SUBDEV_FL_HAS_DEVNODE flag for the subdevice so it is
possible to create a subdevice device node.
Since the driver now depends on VIDEO_V4L2_SUBDEV_API all drivers which
select the driver need to depend on that symbol as well.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Reset the device when initializing it so it is in a good known state and the
assumed register settings matches the actual register settings.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The ad7180 has multiple register pages which can be switched between by
writing to a register. Currently the driver manually switches between pages
whenever a register outside of the default register map is accessed and
switches back after it has been accessed. This is a bit tedious and also
potential source for bugs.
This patch adds two helper functions that take care of switching between
pages and reading/writing the register. The register numbers for registers
are updated to encode both the page (in the upper 8-bits) and the register
(in the lower 8-bits) numbers.
Having multiple pages means that a register access is not a single atomic
i2c_smbus_write_byte_data() or i2c_smbus_read_byte_data() call and we need
to make sure that concurrent register access does not race against each
other.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Consistently prefix register defines with ADV7180_REG. Also remove the "ADI"
from register names, the ADV7180 prefix should provide enough of a namespace
separation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Most IRQ controllers support different types of interrupts. The adv7180
generates falling edge interrupts, so make sure to pass IRQF_TRIGGER_FALLING
to request_threaded_irq() so the IRQ controller is configured for the
correct mode.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently the IRQ is requested from within the init_device() function. This
function is not only called during device probe, but also during resume
causing the driver to try to request the IRQ again. Move requesting the IRQ
from init_device() to the probe function to make sure that it is only
requested once.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is no need to jump to the 'err' label as we can simply return the error
code directly and make the code shorter.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to have subsytem agnostic media bus format definitions we've
moved media bus definitions to include/uapi/linux/media-bus-format.h and
prefixed values with MEDIA_BUS_FMT instead of V4L2_MBUS_FMT.
Replace all references to the old definitions in i2c drivers.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver moved over to v4l2_async_unregister_subdev()
but still retained a call to v4l2_unregister_subdev(). Remove.
Signed-off-by: Ian Molton <ian.molton@codethink.co.uk>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The g_std and s_std operations are video-related, move them to the video
ops where they belong.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is request_irq() in init_device(), but the interrupt is not removed
on failure paths. The patch adds proper error handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The adv7180 has a low power mode in which the analog and the digital processing
section are shut down. Implement the s_power callback to let bridge drivers put
the part into low power mode when not needed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for async device registration to the adv7180 driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The proper way to handle IRQs that need to be able to sleep in their IRQ handler
is to use a threaded IRQ.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Tim Harvey
Sakari Ailus
Kuninori Morimoto
Niklas Söderlund
Hans Verkuil
Andy Shevchenko
Akinobu Mita
Ulrich Hecht
Steve Longerbeam
Julian Scheel
Mauro Carvalho Chehab
Krzysztof Kozlowski
Ben Dooks
Lars-Peter Clausen
Fabio Estevam
Boris BREZILLON
Ian Molton
Laurent Pinchart
Alexey Khoroshilov