This patch adds devicetree node and pinctrl group for I2C1.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch sorts nodes by name and moves "iomux" configuration at
the bottom of file.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds a regulator node and pinctrl group for USB OTG.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Move "hog" pins into corresponded pin groups for eSDHC1, eSDHC2,
eCSPI1, gpio-keys, regulator-fixed and codec clock.
Additionally, this patch fixes GPIO active level definition for
USB regulator.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch allow to define partitions onto NFC in user defined
devicetrees.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch enables UART1 on the phyFLEX connector (i.MX6 uart3).
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The pins labeled UART1 on the module connector are wired to i.MX6 uart3.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds the TLV320, STMPE811, RTC8564, and MX1037 ICs to the I2C2 bus.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Note that the fec driver code currently hard-codes an active-low
reset, regardless of the flags in the device tree.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch enables the red and green GPIO LEDs on Phytec phyFLEX i.MX6 modules.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The PBA-B-01 carrier board can be equipped with either Quad or DualLite/Solo
phyFLEX i.MX6 modules (PFL-A-02).
This moves all common devices into imx6qdl-phytec-pbab01.dtsi. The SoC specific
device trees then just include the pfla01 and pbab01 dtsi files corresponding
to the SoC variant.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Provide an entry for the UART1 pin muxing.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds support for Digi ConnectCore® i.MX51/Wi-i.MX51 SOM
and basic support for the ConnectCore for i.MX51 JumpStart Kit.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch converts all i.MX WEIM users to use single naming style
for devices.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add initial Toradex Colibri VF61 board support. Ethernet, UART
and SDHC cards are working. Cache latencies need to be a bit
higher than vf610.dtsi suggests. Those values are validated
by running multiple memory tests.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Adds toradex to the list of DT vendor prefixes.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
imx27-pdk has 128 MB of DRAM. Pass the memory range in dt.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds display control signal definitions.
These fields are not used in the driver yet, but will be used for
reference to indicate the polarity of the signals.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Use GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW instead of 0 and 1.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fix a copy & paste error: on duckbills the GPIO used for resetting
the ethernet phy differs from FSL's MX28EVK board.
Reported-by: Stefan Wahren <info@lategoodbye.de>
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
I2SE's duckbills are only equipped with a micro SD card slot and
thus only provide a 4-bit interface.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Tested by pinging from the host PC to the imx51-babbage via a g_ether
connection.
Signed-off by: Dave Ebright <dave.ebright@parsons.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This adds devicetree node for VF610, and there are 8 channels
supported.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This IP module is always present and has no external connections.
There is no reason to disable it in the device tree.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
mx25pdk has a sgtl5000 codec connected to the I2C1 port.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Set 'ti,set-rate-parent' property for the dpll4_m5x2_mul_ck clock, which
is used for the ISP functional clock. This fixes the OMAP3 ISP driver's
clock rate configuration, which needs the rate to be propagated properly
to the divider node (dpll4_m5_ck).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
We need to use set-rate-parent for dpll4_m5 clock path, so use the
ti,fixed-factor-clock version which supports set-rate-parent property.
The set-rate-parent flag itself is set in the following patch, this one
just changes the clock driver to ti,fixed-factor-clock without any other
changes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Use the ti,fixed-factor-clock version so that autoidle for
dpll_per_clkdcoldo is properly controlled after power management code
is introduced. Without this the clock may be held active even when
it is gated.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Alexander Shiyan
Philipp Zabel
Fabio Estevam
Denis Carikli
Stefan Agner
Michael Heimpold
Xiubo Li
Laurent Pinchart
Dave Gerlach