The select_idle_sibling() (SIS) rewrite in commit:
10e2f1acd0 ("sched/core: Rewrite and improve select_idle_siblings()")
... replaced a domain iteration with a search that broadly speaking
does a wrapped walk of the scheduler domain sharing a last-level-cache.
While this had a number of improvements, one consequence is that two tasks
that share a waker/wakee relationship push each other around a socket. Even
though two tasks may be active, all cores are evenly used. This is great from
a search perspective and spreads a load across individual cores, but it has
adverse consequences for cpufreq. As each CPU has relatively low utilisation,
cpufreq may decide the utilisation is too low to used a higher P-state and
overall computation throughput suffers.
While individual cpufreq and cpuidle drivers may compensate by artifically
boosting P-state (at c0) or avoiding lower C-states (during idle), it does
not help if hardware-based cpufreq (e.g. HWP) is used.
This patch tracks a recently used CPU based on what CPU a task was running
on when it last was a waker a CPU it was recently using when a task is a
wakee. During SIS, the recently used CPU is used as a target if it's still
allowed by the task and is idle.
The benefit may be non-obvious so consider an example of two tasks
communicating back and forth. Task A may be an application doing IO where
task B is a kworker or kthread like journald. Task A may issue IO, wake
B and B wakes up A on completion. With the existing scheme this may look
like the following (potentially different IDs if SMT is in use but similar
principal applies).
A (cpu 0) wake B (wakes on cpu 1)
B (cpu 1) wake A (wakes on cpu 2)
A (cpu 2) wake B (wakes on cpu 3)
etc.
A careful reader may wonder why CPU 0 was not idle when B wakes A the
first time and it's simply due to the fact that A can be rescheduled to
another CPU and the pattern is that prev == target when B tries to wakeup A
and the information about CPU 0 has been lost.
With this patch, the pattern is more likely to be:
A (cpu 0) wake B (wakes on cpu 1)
B (cpu 1) wake A (wakes on cpu 0)
A (cpu 0) wake B (wakes on cpu 1)
etc
i.e. two communicating casts are more likely to use just two cores instead
of all available cores sharing a LLC.
The most dramatic speedup was noticed on dbench using the XFS filesystem on
UMA as clients interact heavily with workqueues in that configuration. Note
that a similar speedup is not observed on ext4 as the wakeup pattern
is different:
4.15.0-rc9 4.15.0-rc9
waprev-v1 biasancestor-v1
Hmean 1 287.54 ( 0.00%) 817.01 ( 184.14%)
Hmean 2 1268.12 ( 0.00%) 1781.24 ( 40.46%)
Hmean 4 1739.68 ( 0.00%) 1594.47 ( -8.35%)
Hmean 8 2464.12 ( 0.00%) 2479.56 ( 0.63%)
Hmean 64 1455.57 ( 0.00%) 1434.68 ( -1.44%)
The results can be less dramatic on NUMA where automatic balancing interferes
with the test. It's also known that network benchmarks running on localhost
also benefit quite a bit from this patch (roughly 10% on netperf RR for UDP
and TCP depending on the machine). Hackbench also seens small improvements
(6-11% depending on machine and thread count). The facebook schbench was also
tested but in most cases showed little or no different to wakeup latencies.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180130104555.4125-5-mgorman@techsingularity.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
wake_affine_idle() prefers to move a task to the current CPU if the
wakeup is due to an interrupt. The expectation is that the interrupt
data is cache hot and relevant to the waking task as well as avoiding
a search. However, there is no way to determine if there was cache hot
data on the previous CPU that may exceed the interrupt data. Furthermore,
round-robin delivery of interrupts can migrate tasks around a socket where
each CPU is under-utilised. This can interact badly with cpufreq which
makes decisions based on per-cpu data. It has been observed on machines
with HWP that p-states are not boosted to their maximum levels even though
the workload is latency and throughput sensitive.
This patch uses the previous CPU for the task if it's idle and cache-affine
with the current CPU even if the current CPU is idle due to the wakup
being related to the interrupt. This reduces migrations at the cost of
the interrupt data not being cache hot when the task wakes.
A variety of workloads were tested on various machines and no adverse
impact was noticed that was outside noise. dbench on ext4 on UMA showed
roughly 10% reduction in the number of CPU migrations and it is a case
where interrupts are frequent for IO competions. In most cases, the
difference in performance is quite small but variability is often
reduced. For example, this is the result for pgbench running on a UMA
machine with different numbers of clients.
4.15.0-rc9 4.15.0-rc9
baseline waprev-v1
Hmean 1 22096.28 ( 0.00%) 22734.86 ( 2.89%)
Hmean 4 74633.42 ( 0.00%) 75496.77 ( 1.16%)
Hmean 7 115017.50 ( 0.00%) 113030.81 ( -1.73%)
Hmean 12 126209.63 ( 0.00%) 126613.40 ( 0.32%)
Hmean 16 131886.91 ( 0.00%) 130844.35 ( -0.79%)
Stddev 1 636.38 ( 0.00%) 417.11 ( 34.46%)
Stddev 4 614.64 ( 0.00%) 583.24 ( 5.11%)
Stddev 7 542.46 ( 0.00%) 435.45 ( 19.73%)
Stddev 12 173.93 ( 0.00%) 171.50 ( 1.40%)
Stddev 16 671.42 ( 0.00%) 680.30 ( -1.32%)
CoeffVar 1 2.88 ( 0.00%) 1.83 ( 36.26%)
Note that the different in performance is marginal but for low utilisation,
there is less variability.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180130104555.4125-4-mgorman@techsingularity.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This is a preparation patch that has wake_affine*() return a CPU ID instead of
a boolean. The intent is to allow the wake_affine() helpers to be avoided
if a decision is already made. This patch has no functional change.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180130104555.4125-3-mgorman@techsingularity.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
wake_affine_idle() takes parameters it never uses so clean it up.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180130104555.4125-2-mgorman@techsingularity.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
rq->clock_task may be updated between the two calls of
rq_clock_task() in update_curr_rt(). Calling rq_clock_task() only
once makes it more accurate and efficient, taking update_curr() as
reference.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Jiang Biao <jiang.biao2@zte.com.cn>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: zhong.weidong@zte.com.cn
Link: http://lkml.kernel.org/r/1517800721-42092-1-git-send-email-wen.yang99@zte.com.cn
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When issuing an IPI RT push, where an IPI is sent to each CPU that has more
than one RT task scheduled on it, it references the root domain's rto_mask,
that contains all the CPUs within the root domain that has more than one RT
task in the runable state. The problem is, after the IPIs are initiated, the
rq->lock is released. This means that the root domain that is associated to
the run queue could be freed while the IPIs are going around.
Add a sched_get_rd() and a sched_put_rd() that will increment and decrement
the root domain's ref count respectively. This way when initiating the IPIs,
the scheduler will up the root domain's ref count before releasing the
rq->lock, ensuring that the root domain does not go away until the IPI round
is complete.
Reported-by: Pavan Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 4bdced5c9a ("sched/rt: Simplify the IPI based RT balancing logic")
Link: http://lkml.kernel.org/r/CAEU1=PkiHO35Dzna8EQqNSKW1fr1y1zRQ5y66X117MG06sQtNA@mail.gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When the rto_push_irq_work_func() is called, it looks at the RT overloaded
bitmask in the root domain via the runqueue (rq->rd). The problem is that
during CPU up and down, nothing here stops rq->rd from changing between
taking the rq->rd->rto_lock and releasing it. That means the lock that is
released is not the same lock that was taken.
Instead of using this_rq()->rd to get the root domain, as the irq work is
part of the root domain, we can simply get the root domain from the irq work
that is passed to the routine:
container_of(work, struct root_domain, rto_push_work)
This keeps the root domain consistent.
Reported-by: Pavan Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 4bdced5c9a ("sched/rt: Simplify the IPI based RT balancing logic")
Link: http://lkml.kernel.org/r/CAEU1=PkiHO35Dzna8EQqNSKW1fr1y1zRQ5y66X117MG06sQtNA@mail.gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
These functions are already gated by schedstats_enabled(), there is no
point in then issuing another static_branch for every individual
update in them.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The whole of ttwu_stat() is guarded by a single schedstat_enabled(),
there is absolutely no point in then issuing another static_branch for
every single schedstat_inc() in there.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Provide core serializing membarrier command to support memory reclaim
by JIT.
Each architecture needs to explicitly opt into that support by
documenting in their architecture code how they provide the core
serializing instructions required when returning from the membarrier
IPI, and after the scheduler has updated the curr->mm pointer (before
going back to user-space). They should then select
ARCH_HAS_MEMBARRIER_SYNC_CORE to enable support for that command on
their architecture.
Architectures selecting this feature need to either document that
they issue core serializing instructions when returning to user-space,
or implement their architecture-specific sync_core_before_usermode().
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrea Parri <parri.andrea@gmail.com>
Cc: Andrew Hunter <ahh@google.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Avi Kivity <avi@scylladb.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Dave Watson <davejwatson@fb.com>
Cc: David Sehr <sehr@google.com>
Cc: Greg Hackmann <ghackmann@google.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maged Michael <maged.michael@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-api@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Link: http://lkml.kernel.org/r/20180129202020.8515-9-mathieu.desnoyers@efficios.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Allow expedited membarrier to be used for data shared between processes
through shared memory.
Processes wishing to receive the membarriers register with
MEMBARRIER_CMD_REGISTER_GLOBAL_EXPEDITED. Those which want to issue
membarrier invoke MEMBARRIER_CMD_GLOBAL_EXPEDITED.
This allows extremely simple kernel-level implementation: we have almost
everything we need with the PRIVATE_EXPEDITED barrier code. All we need
to do is to add a flag in the mm_struct that will be used to check
whether we need to send the IPI to the current thread of each CPU.
There is a slight downside to this approach compared to targeting
specific shared memory users: when performing a membarrier operation,
all registered "global" receivers will get the barrier, even if they
don't share a memory mapping with the sender issuing
MEMBARRIER_CMD_GLOBAL_EXPEDITED.
This registration approach seems to fit the requirement of not
disturbing processes that really deeply care about real-time: they
simply should not register with MEMBARRIER_CMD_REGISTER_GLOBAL_EXPEDITED.
In order to align the membarrier command names, the "MEMBARRIER_CMD_SHARED"
command is renamed to "MEMBARRIER_CMD_GLOBAL", keeping an alias of
MEMBARRIER_CMD_SHARED to MEMBARRIER_CMD_GLOBAL for UAPI header backward
compatibility.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrea Parri <parri.andrea@gmail.com>
Cc: Andrew Hunter <ahh@google.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Avi Kivity <avi@scylladb.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Dave Watson <davejwatson@fb.com>
Cc: David Sehr <sehr@google.com>
Cc: Greg Hackmann <ghackmann@google.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maged Michael <maged.michael@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-api@vger.kernel.org
Link: http://lkml.kernel.org/r/20180129202020.8515-5-mathieu.desnoyers@efficios.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Document the membarrier requirement on having a full memory barrier in
__schedule() after coming from user-space, before storing to rq->curr.
It is provided by smp_mb__after_spinlock() in __schedule().
Document that membarrier requires a full barrier on transition from
kernel thread to userspace thread. We currently have an implicit barrier
from atomic_dec_and_test() in mmdrop() that ensures this.
The x86 switch_mm_irqs_off() full barrier is currently provided by many
cpumask update operations as well as write_cr3(). Document that
write_cr3() provides this barrier.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrea Parri <parri.andrea@gmail.com>
Cc: Andrew Hunter <ahh@google.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Avi Kivity <avi@scylladb.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Dave Watson <davejwatson@fb.com>
Cc: David Sehr <sehr@google.com>
Cc: Greg Hackmann <ghackmann@google.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maged Michael <maged.michael@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-api@vger.kernel.org
Link: http://lkml.kernel.org/r/20180129202020.8515-4-mathieu.desnoyers@efficios.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Allow PowerPC to skip the full memory barrier in switch_mm(), and
only issue the barrier when scheduling into a task belonging to a
process that has registered to use expedited private.
Threads targeting the same VM but which belong to different thread
groups is a tricky case. It has a few consequences:
It turns out that we cannot rely on get_nr_threads(p) to count the
number of threads using a VM. We can use
(atomic_read(&mm->mm_users) == 1 && get_nr_threads(p) == 1)
instead to skip the synchronize_sched() for cases where the VM only has
a single user, and that user only has a single thread.
It also turns out that we cannot use for_each_thread() to set
thread flags in all threads using a VM, as it only iterates on the
thread group.
Therefore, test the membarrier state variable directly rather than
relying on thread flags. This means
membarrier_register_private_expedited() needs to set the
MEMBARRIER_STATE_PRIVATE_EXPEDITED flag, issue synchronize_sched(), and
only then set MEMBARRIER_STATE_PRIVATE_EXPEDITED_READY which allows
private expedited membarrier commands to succeed.
membarrier_arch_switch_mm() now tests for the
MEMBARRIER_STATE_PRIVATE_EXPEDITED flag.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrea Parri <parri.andrea@gmail.com>
Cc: Andrew Hunter <ahh@google.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Avi Kivity <avi@scylladb.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Dave Watson <davejwatson@fb.com>
Cc: David Sehr <sehr@google.com>
Cc: Greg Hackmann <ghackmann@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maged Michael <maged.michael@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-api@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/20180129202020.8515-3-mathieu.desnoyers@efficios.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull printk updates from Petr Mladek:
- Add a console_msg_format command line option:
The value "default" keeps the old "[time stamp] text\n" format. The
value "syslog" allows to see the syslog-like "<log
level>[timestamp] text" format.
This feature was requested by people doing regression tests, for
example, 0day robot. They want to have both filtered and full logs
at hands.
- Reduce the risk of softlockup:
Pass the console owner in a busy loop.
This is a new approach to the old problem. It was first proposed by
Steven Rostedt on Kernel Summit 2017. It marks a context in which
the console_lock owner calls console drivers and could not sleep.
On the other side, printk() callers could detect this state and use
a busy wait instead of a simple console_trylock(). Finally, the
console_lock owner checks if there is a busy waiter at the end of
the special context and eventually passes the console_lock to the
waiter.
The hand-off works surprisingly well and helps in many situations.
Well, there is still a possibility of the softlockup, for example,
when the flood of messages stops and the last owner still has too
much to flush.
There is increasing number of people having problems with
printk-related softlockups. We might eventually need to get better
solution. Anyway, this looks like a good start and promising
direction.
- Do not allow to schedule in console_unlock() called from printk():
This reverts an older controversial commit. The reschedule helped
to avoid softlockups. But it also slowed down the console output.
This patch is obsoleted by the new console waiter logic described
above. In fact, the reschedule made the hand-off less effective.
- Deprecate "%pf" and "%pF" format specifier:
It was needed on ia64, ppc64 and parisc64 to dereference function
descriptors and show the real function address. It is done
transparently by "%ps" and "pS" format specifier now.
Sergey Senozhatsky found that all the function descriptors were in
a special elf section and could be easily detected.
- Remove printk_symbol() API:
It has been obsoleted by "%pS" format specifier, and this change
helped to remove few continuous lines and a less intuitive old API.
- Remove redundant memsets:
Sergey removed unnecessary memset when processing printk.devkmsg
command line option.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk: (27 commits)
printk: drop redundant devkmsg_log_str memsets
printk: Never set console_may_schedule in console_trylock()
printk: Hide console waiter logic into helpers
printk: Add console owner and waiter logic to load balance console writes
kallsyms: remove print_symbol() function
checkpatch: add pF/pf deprecation warning
symbol lookup: introduce dereference_symbol_descriptor()
parisc64: Add .opd based function descriptor dereference
powerpc64: Add .opd based function descriptor dereference
ia64: Add .opd based function descriptor dereference
sections: split dereference_function_descriptor()
openrisc: Fix conflicting types for _exext and _stext
lib: do not use print_symbol()
irq debug: do not use print_symbol()
sysfs: do not use print_symbol()
drivers: do not use print_symbol()
x86: do not use print_symbol()
unicore32: do not use print_symbol()
sh: do not use print_symbol()
mn10300: do not use print_symbol()
...
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle were:
- Implement frequency/CPU invariance and OPP selection for
SCHED_DEADLINE (Juri Lelli)
- Tweak the task migration logic for better multi-tasking
workload scalability (Mel Gorman)
- Misc cleanups, fixes and improvements"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/deadline: Make bandwidth enforcement scale-invariant
sched/cpufreq: Move arch_scale_{freq,cpu}_capacity() outside of #ifdef CONFIG_SMP
sched/cpufreq: Remove arch_scale_freq_capacity()'s 'sd' parameter
sched/cpufreq: Always consider all CPUs when deciding next freq
sched/cpufreq: Split utilization signals
sched/cpufreq: Change the worker kthread to SCHED_DEADLINE
sched/deadline: Move CPU frequency selection triggering points
sched/cpufreq: Use the DEADLINE utilization signal
sched/deadline: Implement "runtime overrun signal" support
sched/fair: Only immediately migrate tasks due to interrupts if prev and target CPUs share cache
sched/fair: Correct obsolete comment about cpufreq_update_util()
sched/fair: Remove impossible condition from find_idlest_group_cpu()
sched/cpufreq: Don't pass flags to sugov_set_iowait_boost()
sched/cpufreq: Initialize sg_cpu->flags to 0
sched/fair: Consider RT/IRQ pressure in capacity_spare_wake()
sched/fair: Use 'unsigned long' for utilization, consistently
sched/core: Rework and clarify prepare_lock_switch()
sched/fair: Remove unused 'curr' parameter from wakeup_gran
sched/headers: Constify object_is_on_stack()
Pull RCU updates from Ingo Molnar:
"The main RCU changes in this cycle were:
- Updates to use cond_resched() instead of cond_resched_rcu_qs()
where feasible (currently everywhere except in kernel/rcu and in
kernel/torture.c). Also a couple of fixes to avoid sending IPIs to
offline CPUs.
- Updates to simplify RCU's dyntick-idle handling.
- Updates to remove almost all uses of smp_read_barrier_depends() and
read_barrier_depends().
- Torture-test updates.
- Miscellaneous fixes"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (72 commits)
torture: Save a line in stutter_wait(): while -> for
torture: Eliminate torture_runnable and perf_runnable
torture: Make stutter less vulnerable to compilers and races
locking/locktorture: Fix num reader/writer corner cases
locking/locktorture: Fix rwsem reader_delay
torture: Place all torture-test modules in one MAINTAINERS group
rcutorture/kvm-build.sh: Skip build directory check
rcutorture: Simplify functions.sh include path
rcutorture: Simplify logging
rcutorture/kvm-recheck-*: Improve result directory readability check
rcutorture/kvm.sh: Support execution from any directory
rcutorture/kvm.sh: Use consistent help text for --qemu-args
rcutorture/kvm.sh: Remove unused variable, `alldone`
rcutorture: Remove unused script, config2frag.sh
rcutorture/configinit: Fix build directory error message
rcutorture: Preempt RCU-preempt readers more vigorously
torture: Reduce #ifdefs for preempt_schedule()
rcu: Remove have_rcu_nocb_mask from tree_plugin.h
rcu: Add comment giving debug strategy for double call_rcu()
tracing, rcu: Hide trace event rcu_nocb_wake when not used
...
Before commit:
e33a9bba85 ("sched/core: move IO scheduling accounting from io_schedule_timeout() into scheduler")
delayacct_blkio_end() was called after context-switching into the task which
completed I/O.
This resulted in double counting: the task would account a delay both waiting
for I/O and for time spent in the runqueue.
With e33a9bba85, delayacct_blkio_end() is called by try_to_wake_up().
In ttwu, we have not yet context-switched. This is more correct, in that
the delay accounting ends when the I/O is complete.
But delayacct_blkio_end() relies on 'get_current()', and we have not yet
context-switched into the task whose I/O completed. This results in the
wrong task having its delay accounting statistics updated.
Instead of doing that, pass the task_struct being woken to delayacct_blkio_end(),
so that it can update the statistics of the correct task.
Signed-off-by: Josh Snyder <joshs@netflix.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Cc: <stable@vger.kernel.org>
Cc: Brendan Gregg <bgregg@netflix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-block@vger.kernel.org
Fixes: e33a9bba85 ("sched/core: move IO scheduling accounting from io_schedule_timeout() into scheduler")
Link: http://lkml.kernel.org/r/1513613712-571-1-git-send-email-joshs@netflix.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull scheduler fixes from Ingo Molnar:
"A Kconfig fix, a build fix and a membarrier bug fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
membarrier: Disable preemption when calling smp_call_function_many()
sched/isolation: Make CONFIG_CPU_ISOLATION=y depend on SMP or COMPILE_TEST
ia64, sched/cputime: Fix build error if CONFIG_VIRT_CPU_ACCOUNTING_NATIVE=y
This patch adds the possibility of getting the delivery of a SIGXCPU
signal whenever there is a runtime overrun. The request is done through
the sched_flags field within the sched_attr structure.
Forward port of https://lkml.org/lkml/2009/10/16/170
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Juri Lelli <juri.lelli@gmail.com>
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Luca Abeni <luca.abeni@santannapisa.it>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tommaso Cucinotta <tommaso.cucinotta@sssup.it>
Link: http://lkml.kernel.org/r/1513077024-25461-1-git-send-email-claudio@evidence.eu.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If waking from an idle CPU due to an interrupt then it's possible that
the waker task will be pulled to wake on the current CPU. Unfortunately,
depending on the type of interrupt and IRQ configuration, there may not
be a strong relationship between the CPU an interrupt was delivered on
and the CPU a task was running on. For example, the interrupts could all
be delivered to CPUs on one particular node due to the machine topology
or IRQ affinity configuration. Another example is an interrupt for an IO
completion which can be delivered to any CPU where there is no guarantee
the data is either cache hot or even local.
This patch was motivated by the observation that an IO workload was
being pulled cross-node on a frequent basis when IO completed. From a
wakeup latency perspective, it's still useful to know that an idle CPU is
immediately available for use but lets only consider an automatic migration
if the CPUs share cache to limit damage due to NUMA migrations. Migrations
may still occur if wake_affine_weight determines it's appropriate.
These are the throughput results for dbench running on ext4 comparing
4.15-rc3 and this patch on a 2-socket machine where interrupts due to IO
completions can happen on any CPU.
4.15.0-rc3 4.15.0-rc3
vanilla lessmigrate
Hmean 1 854.64 ( 0.00%) 865.01 ( 1.21%)
Hmean 2 1229.60 ( 0.00%) 1274.44 ( 3.65%)
Hmean 4 1591.81 ( 0.00%) 1628.08 ( 2.28%)
Hmean 8 1845.04 ( 0.00%) 1831.80 ( -0.72%)
Hmean 16 2038.61 ( 0.00%) 2091.44 ( 2.59%)
Hmean 32 2327.19 ( 0.00%) 2430.29 ( 4.43%)
Hmean 64 2570.61 ( 0.00%) 2568.54 ( -0.08%)
Hmean 128 2481.89 ( 0.00%) 2499.28 ( 0.70%)
Stddev 1 14.31 ( 0.00%) 5.35 ( 62.65%)
Stddev 2 21.29 ( 0.00%) 11.09 ( 47.92%)
Stddev 4 7.22 ( 0.00%) 6.80 ( 5.92%)
Stddev 8 26.70 ( 0.00%) 9.41 ( 64.76%)
Stddev 16 22.40 ( 0.00%) 20.01 ( 10.70%)
Stddev 32 45.13 ( 0.00%) 44.74 ( 0.85%)
Stddev 64 93.10 ( 0.00%) 93.18 ( -0.09%)
Stddev 128 184.28 ( 0.00%) 177.85 ( 3.49%)
Note the small increase in throughput for low thread counts but also
note that the standard deviation for each sample during the test run is
lower. The throughput figures for dbench can be misleading so the benchmark
is actually modified to time the latency of the processing of one load
file with many samples taken. The difference in latency is
4.15.0-rc3 4.15.0-rc3
vanilla lessmigrate
Amean 1 21.71 ( 0.00%) 21.47 ( 1.08%)
Amean 2 30.89 ( 0.00%) 29.58 ( 4.26%)
Amean 4 47.54 ( 0.00%) 46.61 ( 1.97%)
Amean 8 82.71 ( 0.00%) 82.81 ( -0.12%)
Amean 16 149.45 ( 0.00%) 145.01 ( 2.97%)
Amean 32 265.49 ( 0.00%) 248.43 ( 6.42%)
Amean 64 463.23 ( 0.00%) 463.55 ( -0.07%)
Amean 128 933.97 ( 0.00%) 935.50 ( -0.16%)
Stddev 1 1.58 ( 0.00%) 1.54 ( 2.26%)
Stddev 2 2.84 ( 0.00%) 2.95 ( -4.15%)
Stddev 4 6.78 ( 0.00%) 6.85 ( -0.99%)
Stddev 8 16.85 ( 0.00%) 16.37 ( 2.85%)
Stddev 16 41.59 ( 0.00%) 41.04 ( 1.32%)
Stddev 32 111.05 ( 0.00%) 105.11 ( 5.35%)
Stddev 64 285.94 ( 0.00%) 288.01 ( -0.72%)
Stddev 128 803.39 ( 0.00%) 809.73 ( -0.79%)
It's a small improvement which is not surprising given that migrations that
migrate to a different node as not that common. However, it is noticeable
in the CPU migration statistics which are reduced by 24%.
There was a query for v1 of this patch about NAS so here are the results
for C-class using MPI for parallelisation on the same machine
nas-mpi
4.15.0-rc3 4.15.0-rc3
vanilla noirq
Time cg.C 24.25 ( 0.00%) 23.17 ( 4.45%)
Time ep.C 8.22 ( 0.00%) 8.29 ( -0.85%)
Time ft.C 22.67 ( 0.00%) 20.34 ( 10.28%)
Time is.C 1.42 ( 0.00%) 1.47 ( -3.52%)
Time lu.C 55.62 ( 0.00%) 54.81 ( 1.46%)
Time mg.C 7.93 ( 0.00%) 7.91 ( 0.25%)
4.15.0-rc3 4.15.0-rc3
vanilla noirq-v1r1
User 3799.96 3748.34
System 672.10 626.15
Elapsed 91.91 79.49
lu.C sees a small gain, ft.C a large gain and ep.C and is.C see small
regressions but in terms of absolute time, the difference is small and
likely within run-to-run variance. System CPU usage is slightly reduced.
schbench from Facebook was also requested. This is a bit of a mixed bag but
it's important to note that this workload should not be heavily impacted
by wakeups from interrupt context.
4.15.0-rc3 4.15.0-rc3
vanilla noirq-v1r1
Lat 50.00th-qrtle-1 41.00 ( 0.00%) 41.00 ( 0.00%)
Lat 75.00th-qrtle-1 42.00 ( 0.00%) 42.00 ( 0.00%)
Lat 90.00th-qrtle-1 43.00 ( 0.00%) 44.00 ( -2.33%)
Lat 95.00th-qrtle-1 44.00 ( 0.00%) 46.00 ( -4.55%)
Lat 99.00th-qrtle-1 57.00 ( 0.00%) 58.00 ( -1.75%)
Lat 99.50th-qrtle-1 59.00 ( 0.00%) 59.00 ( 0.00%)
Lat 99.90th-qrtle-1 67.00 ( 0.00%) 78.00 ( -16.42%)
Lat 50.00th-qrtle-2 40.00 ( 0.00%) 51.00 ( -27.50%)
Lat 75.00th-qrtle-2 45.00 ( 0.00%) 56.00 ( -24.44%)
Lat 90.00th-qrtle-2 53.00 ( 0.00%) 59.00 ( -11.32%)
Lat 95.00th-qrtle-2 57.00 ( 0.00%) 61.00 ( -7.02%)
Lat 99.00th-qrtle-2 67.00 ( 0.00%) 71.00 ( -5.97%)
Lat 99.50th-qrtle-2 69.00 ( 0.00%) 74.00 ( -7.25%)
Lat 99.90th-qrtle-2 83.00 ( 0.00%) 77.00 ( 7.23%)
Lat 50.00th-qrtle-4 51.00 ( 0.00%) 51.00 ( 0.00%)
Lat 75.00th-qrtle-4 57.00 ( 0.00%) 56.00 ( 1.75%)
Lat 90.00th-qrtle-4 60.00 ( 0.00%) 59.00 ( 1.67%)
Lat 95.00th-qrtle-4 62.00 ( 0.00%) 62.00 ( 0.00%)
Lat 99.00th-qrtle-4 73.00 ( 0.00%) 72.00 ( 1.37%)
Lat 99.50th-qrtle-4 76.00 ( 0.00%) 74.00 ( 2.63%)
Lat 99.90th-qrtle-4 85.00 ( 0.00%) 78.00 ( 8.24%)
Lat 50.00th-qrtle-8 54.00 ( 0.00%) 58.00 ( -7.41%)
Lat 75.00th-qrtle-8 59.00 ( 0.00%) 62.00 ( -5.08%)
Lat 90.00th-qrtle-8 65.00 ( 0.00%) 66.00 ( -1.54%)
Lat 95.00th-qrtle-8 67.00 ( 0.00%) 70.00 ( -4.48%)
Lat 99.00th-qrtle-8 78.00 ( 0.00%) 79.00 ( -1.28%)
Lat 99.50th-qrtle-8 81.00 ( 0.00%) 80.00 ( 1.23%)
Lat 99.90th-qrtle-8 116.00 ( 0.00%) 83.00 ( 28.45%)
Lat 50.00th-qrtle-16 65.00 ( 0.00%) 64.00 ( 1.54%)
Lat 75.00th-qrtle-16 77.00 ( 0.00%) 71.00 ( 7.79%)
Lat 90.00th-qrtle-16 83.00 ( 0.00%) 82.00 ( 1.20%)
Lat 95.00th-qrtle-16 87.00 ( 0.00%) 87.00 ( 0.00%)
Lat 99.00th-qrtle-16 95.00 ( 0.00%) 96.00 ( -1.05%)
Lat 99.50th-qrtle-16 99.00 ( 0.00%) 103.00 ( -4.04%)
Lat 99.90th-qrtle-16 104.00 ( 0.00%) 122.00 ( -17.31%)
Lat 50.00th-qrtle-32 71.00 ( 0.00%) 73.00 ( -2.82%)
Lat 75.00th-qrtle-32 91.00 ( 0.00%) 92.00 ( -1.10%)
Lat 90.00th-qrtle-32 108.00 ( 0.00%) 107.00 ( 0.93%)
Lat 95.00th-qrtle-32 118.00 ( 0.00%) 115.00 ( 2.54%)
Lat 99.00th-qrtle-32 134.00 ( 0.00%) 129.00 ( 3.73%)
Lat 99.50th-qrtle-32 138.00 ( 0.00%) 133.00 ( 3.62%)
Lat 99.90th-qrtle-32 149.00 ( 0.00%) 146.00 ( 2.01%)
Lat 50.00th-qrtle-39 83.00 ( 0.00%) 81.00 ( 2.41%)
Lat 75.00th-qrtle-39 105.00 ( 0.00%) 102.00 ( 2.86%)
Lat 90.00th-qrtle-39 120.00 ( 0.00%) 119.00 ( 0.83%)
Lat 95.00th-qrtle-39 129.00 ( 0.00%) 128.00 ( 0.78%)
Lat 99.00th-qrtle-39 153.00 ( 0.00%) 149.00 ( 2.61%)
Lat 99.50th-qrtle-39 166.00 ( 0.00%) 156.00 ( 6.02%)
Lat 99.90th-qrtle-39 12304.00 ( 0.00%) 12848.00 ( -4.42%)
When heavily loaded (e.g. 99.50th-qrtle-39 indicates 39 threads), there
are small gains in many cases. Otherwise it depends on the quartile used
where it can be bad -- e.g. 75.00th-qrtle-2. However, even these results
are probably a co-incidence. For this workload, much depends on what node
the threads get placed on and their relative locality and not wakeups from
interrupt context. A larger component on how it behaves would be automatic
NUMA balancing where a fault incurred to measure locality would be a much
larger contributer to latency than the wakeup path.
This is the results from an almost identical machine that happened to run
the same test. They only differ in terms of storage which is irrelevant
for this test.
4.15.0-rc3 4.15.0-rc3
vanilla noirq-v1r1
Lat 50.00th-qrtle-1 41.00 ( 0.00%) 41.00 ( 0.00%)
Lat 75.00th-qrtle-1 42.00 ( 0.00%) 42.00 ( 0.00%)
Lat 90.00th-qrtle-1 44.00 ( 0.00%) 43.00 ( 2.27%)
Lat 95.00th-qrtle-1 53.00 ( 0.00%) 45.00 ( 15.09%)
Lat 99.00th-qrtle-1 59.00 ( 0.00%) 58.00 ( 1.69%)
Lat 99.50th-qrtle-1 60.00 ( 0.00%) 59.00 ( 1.67%)
Lat 99.90th-qrtle-1 86.00 ( 0.00%) 61.00 ( 29.07%)
Lat 50.00th-qrtle-2 52.00 ( 0.00%) 41.00 ( 21.15%)
Lat 75.00th-qrtle-2 57.00 ( 0.00%) 46.00 ( 19.30%)
Lat 90.00th-qrtle-2 60.00 ( 0.00%) 53.00 ( 11.67%)
Lat 95.00th-qrtle-2 62.00 ( 0.00%) 57.00 ( 8.06%)
Lat 99.00th-qrtle-2 73.00 ( 0.00%) 68.00 ( 6.85%)
Lat 99.50th-qrtle-2 74.00 ( 0.00%) 71.00 ( 4.05%)
Lat 99.90th-qrtle-2 90.00 ( 0.00%) 75.00 ( 16.67%)
Lat 50.00th-qrtle-4 57.00 ( 0.00%) 52.00 ( 8.77%)
Lat 75.00th-qrtle-4 60.00 ( 0.00%) 58.00 ( 3.33%)
Lat 90.00th-qrtle-4 62.00 ( 0.00%) 62.00 ( 0.00%)
Lat 95.00th-qrtle-4 65.00 ( 0.00%) 65.00 ( 0.00%)
Lat 99.00th-qrtle-4 76.00 ( 0.00%) 75.00 ( 1.32%)
Lat 99.50th-qrtle-4 77.00 ( 0.00%) 77.00 ( 0.00%)
Lat 99.90th-qrtle-4 87.00 ( 0.00%) 81.00 ( 6.90%)
Lat 50.00th-qrtle-8 59.00 ( 0.00%) 57.00 ( 3.39%)
Lat 75.00th-qrtle-8 63.00 ( 0.00%) 62.00 ( 1.59%)
Lat 90.00th-qrtle-8 66.00 ( 0.00%) 67.00 ( -1.52%)
Lat 95.00th-qrtle-8 68.00 ( 0.00%) 70.00 ( -2.94%)
Lat 99.00th-qrtle-8 79.00 ( 0.00%) 80.00 ( -1.27%)
Lat 99.50th-qrtle-8 80.00 ( 0.00%) 84.00 ( -5.00%)
Lat 99.90th-qrtle-8 84.00 ( 0.00%) 90.00 ( -7.14%)
Lat 50.00th-qrtle-16 65.00 ( 0.00%) 65.00 ( 0.00%)
Lat 75.00th-qrtle-16 77.00 ( 0.00%) 75.00 ( 2.60%)
Lat 90.00th-qrtle-16 84.00 ( 0.00%) 83.00 ( 1.19%)
Lat 95.00th-qrtle-16 88.00 ( 0.00%) 87.00 ( 1.14%)
Lat 99.00th-qrtle-16 97.00 ( 0.00%) 96.00 ( 1.03%)
Lat 99.50th-qrtle-16 100.00 ( 0.00%) 104.00 ( -4.00%)
Lat 99.90th-qrtle-16 110.00 ( 0.00%) 126.00 ( -14.55%)
Lat 50.00th-qrtle-32 70.00 ( 0.00%) 71.00 ( -1.43%)
Lat 75.00th-qrtle-32 92.00 ( 0.00%) 94.00 ( -2.17%)
Lat 90.00th-qrtle-32 110.00 ( 0.00%) 110.00 ( 0.00%)
Lat 95.00th-qrtle-32 121.00 ( 0.00%) 118.00 ( 2.48%)
Lat 99.00th-qrtle-32 135.00 ( 0.00%) 137.00 ( -1.48%)
Lat 99.50th-qrtle-32 140.00 ( 0.00%) 146.00 ( -4.29%)
Lat 99.90th-qrtle-32 150.00 ( 0.00%) 160.00 ( -6.67%)
Lat 50.00th-qrtle-39 80.00 ( 0.00%) 71.00 ( 11.25%)
Lat 75.00th-qrtle-39 102.00 ( 0.00%) 91.00 ( 10.78%)
Lat 90.00th-qrtle-39 118.00 ( 0.00%) 108.00 ( 8.47%)
Lat 95.00th-qrtle-39 128.00 ( 0.00%) 117.00 ( 8.59%)
Lat 99.00th-qrtle-39 149.00 ( 0.00%) 133.00 ( 10.74%)
Lat 99.50th-qrtle-39 160.00 ( 0.00%) 139.00 ( 13.12%)
Lat 99.90th-qrtle-39 13808.00 ( 0.00%) 4920.00 ( 64.37%)
Despite being nearly identical, it showed a variety of major gains so
I'm not convinced that heavy emphasis should be placed on this particular
workload in terms of evaluating this particular patch. Further evidence of
this is the fact that testing on a UMA machine showed small gains/losses
even though the patch should be a no-op on UMA.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20171219085947.13136-2-mgorman@techsingularity.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since the remote cpufreq callback work, the cpufreq_update_util() call can happen
from remote CPUs. The comment about local CPUs is thus obsolete. Update it
accordingly.
Signed-off-by: Joel Fernandes <joelaf@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Android Kernel <kernel-team@android.com>
Cc: Atish Patra <atish.patra@oracle.com>
Cc: Chris Redpath <Chris.Redpath@arm.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: EAS Dev <eas-dev@lists.linaro.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Juri Lelli <juri.lelli@arm.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten Ramussen <morten.rasmussen@arm.com>
Cc: Patrick Bellasi <patrick.bellasi@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Rohit Jain <rohit.k.jain@oracle.com>
Cc: Saravana Kannan <skannan@quicinc.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Steve Muckle <smuckle@google.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vikram Mulukutla <markivx@codeaurora.org>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Link: http://lkml.kernel.org/r/20171215153944.220146-2-joelaf@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
find_idlest_group_cpu() goes through CPUs of a group previous selected by
find_idlest_group(). find_idlest_group() returns NULL if the local group is the
selected one and doesn't execute find_idlest_group_cpu if the group to which
'cpu' belongs to is chosen. So we're always guaranteed to call
find_idlest_group_cpu() with a group to which 'cpu' is non-local.
This makes one of the conditions in find_idlest_group_cpu() an impossible one,
which we can get rid off.
Signed-off-by: Joel Fernandes <joelaf@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Brendan Jackman <brendan.jackman@arm.com>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Android Kernel <kernel-team@android.com>
Cc: Atish Patra <atish.patra@oracle.com>
Cc: Chris Redpath <Chris.Redpath@arm.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: EAS Dev <eas-dev@lists.linaro.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Juri Lelli <juri.lelli@arm.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten Ramussen <morten.rasmussen@arm.com>
Cc: Patrick Bellasi <patrick.bellasi@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Rohit Jain <rohit.k.jain@oracle.com>
Cc: Saravana Kannan <skannan@quicinc.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Steve Muckle <smuckle@google.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vikram Mulukutla <markivx@codeaurora.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: http://lkml.kernel.org/r/20171215153944.220146-3-joelaf@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Initializing sg_cpu->flags to SCHED_CPUFREQ_RT has no obvious benefit.
The flags field wouldn't be used until the utilization update handler is
called for the first time, and once that is called we will overwrite
flags anyway.
Initialize it to 0.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Juri Lelli <juri.lelli@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael Wysocki <rjw@rjwysocki.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: dietmar.eggemann@arm.com
Cc: joelaf@google.com
Cc: morten.rasmussen@arm.com
Cc: tkjos@android.com
Link: http://lkml.kernel.org/r/763feda6424ced8486b25a0c52979634e6104478.1513158452.git.viresh.kumar@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
capacity_spare_wake() in the slow path influences choice of idlest groups,
as we search for groups with maximum spare capacity. In scenarios where
RT pressure is high, a sub optimal group can be chosen and hurt
performance of the task being woken up.
Fix this by using capacity_of() instead of capacity_orig_of() in capacity_spare_wake().
Tests results from improvements with this change are below. More tests
were also done by myself and Matt Fleming to ensure no degradation in
different benchmarks.
1) Rohit ran barrier.c test (details below) with following improvements:
------------------------------------------------------------------------
This was Rohit's original use case for a patch he posted at [1] however
from his recent tests he showed my patch can replace his slow path
changes [1] and there's no need to selectively scan/skip CPUs in
find_idlest_group_cpu in the slow path to get the improvement he sees.
barrier.c (open_mp code) as a micro-benchmark. It does a number of
iterations and barrier sync at the end of each for loop.
Here barrier,c is running in along with ping on CPU 0 and 1 as:
'ping -l 10000 -q -s 10 -f hostX'
barrier.c can be found at:
http://www.spinics.net/lists/kernel/msg2506955.html
Following are the results for the iterations per second with this
micro-benchmark (higher is better), on a 44 core, 2 socket 88 Threads
Intel x86 machine:
+--------+------------------+---------------------------+
|Threads | Without patch | With patch |
| | | |
+--------+--------+---------+-----------------+---------+
| | Mean | Std Dev | Mean | Std Dev |
+--------+--------+---------+-----------------+---------+
|1 | 539.36 | 60.16 | 572.54 (+6.15%) | 40.95 |
|2 | 481.01 | 19.32 | 530.64 (+10.32%)| 56.16 |
|4 | 474.78 | 22.28 | 479.46 (+0.99%) | 18.89 |
|8 | 450.06 | 24.91 | 447.82 (-0.50%) | 12.36 |
|16 | 436.99 | 22.57 | 441.88 (+1.12%) | 7.39 |
|32 | 388.28 | 55.59 | 429.4 (+10.59%)| 31.14 |
|64 | 314.62 | 6.33 | 311.81 (-0.89%) | 11.99 |
+--------+--------+---------+-----------------+---------+
2) ping+hackbench test on bare-metal sever (by Rohit)
-----------------------------------------------------
Here hackbench is running in threaded mode along
with, running ping on CPU 0 and 1 as:
'ping -l 10000 -q -s 10 -f hostX'
This test is running on 2 socket, 20 core and 40 threads Intel x86
machine:
Number of loops is 10000 and runtime is in seconds (Lower is better).
+--------------+-----------------+--------------------------+
|Task Groups | Without patch | With patch |
| +-------+---------+----------------+---------+
|(Groups of 40)| Mean | Std Dev | Mean | Std Dev |
+--------------+-------+---------+----------------+---------+
|1 | 0.851 | 0.007 | 0.828 (+2.77%)| 0.032 |
|2 | 1.083 | 0.203 | 1.087 (-0.37%)| 0.246 |
|4 | 1.601 | 0.051 | 1.611 (-0.62%)| 0.055 |
|8 | 2.837 | 0.060 | 2.827 (+0.35%)| 0.031 |
|16 | 5.139 | 0.133 | 5.107 (+0.63%)| 0.085 |
|25 | 7.569 | 0.142 | 7.503 (+0.88%)| 0.143 |
+--------------+-------+---------+----------------+---------+
[1] https://patchwork.kernel.org/patch/9991635/
Matt Fleming also ran several different hackbench tests and cyclic test
to santiy-check that the patch doesn't harm other usecases.
Tested-by: Matt Fleming <matt@codeblueprint.co.uk>
Tested-by: Rohit Jain <rohit.k.jain@oracle.com>
Signed-off-by: Joel Fernandes <joelaf@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Atish Patra <atish.patra@oracle.com>
Cc: Brendan Jackman <brendan.jackman@arm.com>
Cc: Chris Redpath <Chris.Redpath@arm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Juri Lelli <juri.lelli@arm.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten Ramussen <morten.rasmussen@arm.com>
Cc: Patrick Bellasi <patrick.bellasi@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Saravana Kannan <skannan@quicinc.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Steve Muckle <smuckle@google.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vikram Mulukutla <markivx@codeaurora.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: http://lkml.kernel.org/r/20171214212158.188190-1-joelaf@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Utilization and capacity are tracked as 'unsigned long', however some
functions using them return an 'int' which is ultimately assigned back to
'unsigned long' variables.
Since there is not scope on using a different and signed type,
consolidate the signature of functions returning utilization to always
use the native type.
This change improves code consistency, and it also benefits
code paths where utilizations should be clamped by avoiding
further type conversions or ugly type casts.
Signed-off-by: Patrick Bellasi <patrick.bellasi@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Chris Redpath <chris.redpath@arm.com>
Reviewed-by: Brendan Jackman <brendan.jackman@arm.com>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Todd Kjos <tkjos@android.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: http://lkml.kernel.org/r/20171205171018.9203-2-patrick.bellasi@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The prepare_lock_switch() function has an unused parameter, and also the
function name was not descriptive. To improve readability and remove
the extra parameter, do the following changes:
* Move prepare_lock_switch() from kernel/sched/sched.h to
kernel/sched/core.c, rename it to prepare_task(), and remove the
unused parameter.
* Split the smp_store_release() out from finish_lock_switch() to a
function named finish_task.
* Comments ajdustments.
Signed-off-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20171215140603.gxe5i2y6fg5ojfpp@smtp.gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
smp_call_function_many() requires disabling preemption around the call.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: <stable@vger.kernel.org> # v4.14+
Cc: Andrea Parri <parri.andrea@gmail.com>
Cc: Andrew Hunter <ahh@google.com>
Cc: Avi Kivity <avi@scylladb.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Dave Watson <davejwatson@fb.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maged Michael <maged.michael@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul E . McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20171215192310.25293-1-mathieu.desnoyers@efficios.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull RCU updates from Paul E. McKenney:
- Updates to use cond_resched() instead of cond_resched_rcu_qs()
where feasible (currently everywhere except in kernel/rcu and
in kernel/torture.c). Also a couple of fixes to avoid sending
IPIs to offline CPUs.
- Updates to simplify RCU's dyntick-idle handling.
- Updates to remove almost all uses of smp_read_barrier_depends()
and read_barrier_depends().
- Miscellaneous fixes.
- Torture-test updates.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since the recent remote cpufreq callback work, its possible that a cpufreq
update is triggered from a remote CPU. For single policies however, the current
code uses the local CPU when trying to determine if the remote sg_cpu entered
idle or is busy. This is incorrect. To remedy this, compare with the nohz tick
idle_calls counter of the remote CPU.
Fixes: 674e75411f (sched: cpufreq: Allow remote cpufreq callbacks)
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Joel Fernandes <joelaf@google.com>
Cc: 4.14+ <stable@vger.kernel.org> # 4.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Daniel Wagner reported a crash on the BeagleBone Black SoC.
This is a single CPU architecture, and does not have a functional
arch_send_call_function_single_ipi() implementation which can crash
the kernel if that is called.
As it only has one CPU, it shouldn't be called, but if the kernel is
compiled for SMP, the push/pull RT scheduling logic now calls it for
irq_work if the one CPU is overloaded, it can use that function to call
itself and crash the kernel.
Ideally, we should disable the SCHED_FEAT(RT_PUSH_IPI) if the system
only has a single CPU. But SCHED_FEAT is a constant if sched debugging
is turned off. Another fix can also be used, and this should also help
with normal SMP machines. That is, do not initiate the pull code if
there's only one RT overloaded CPU, and that CPU happens to be the
current CPU that is scheduling in a lower priority task.
Even on a system with many CPUs, if there's many RT tasks waiting to
run on a single CPU, and that CPU schedules in another RT task of lower
priority, it will initiate the PULL logic in case there's a higher
priority RT task on another CPU that is waiting to run. But if there is
no other CPU with waiting RT tasks, it will initiate the RT pull logic
on itself (as it still has RT tasks waiting to run). This is a wasted
effort.
Not only does this help with SMP code where the current CPU is the only
one with RT overloaded tasks, it should also solve the issue that
Daniel encountered, because it will prevent the PULL logic from
executing, as there's only one CPU on the system, and the check added
here will cause it to exit the RT pull code.
Reported-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-rt-users <linux-rt-users@vger.kernel.org>
Cc: stable@vger.kernel.org
Fixes: 4bdced5c9 ("sched/rt: Simplify the IPI based RT balancing logic")
Link: http://lkml.kernel.org/r/20171202130454.4cbbfe8d@vmware.local.home
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix the following kernel-doc warnings after code restructuring:
../kernel/sched/core.c:5113: warning: No description found for parameter 't'
../kernel/sched/core.c:5113: warning: Excess function parameter 'interval' description in 'sched_rr_get_interval'
get rid of set_fs()")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: abca5fc535 ("sched_rr_get_interval(): move compat to native,
Link: http://lkml.kernel.org/r/995c6ded-b32e-bbe4-d9f5-4d42d121aff1@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Move local "sched.h" include to the bottom. sched.h defines
several macros that are getting redefined in ARCH-specific
code, for instance, finish_arch_post_lock_switch() and
prepare_arch_switch(), so we need ARCH-specific definitions
to come in first.
Link: http://lkml.kernel.org/r/20171208082422.5021-1-sergey.senozhatsky@gmail.com
To: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: linux-pm@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: linux-mm@kvack.org
Suggested-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Autogroup does not seem to use any of kallsyms functions/defines.
Link: http://lkml.kernel.org/r/20171208025616.16267-2-sergey.senozhatsky@gmail.com
To: Andrew Morton <akpm@linux-foundation.org>
To: Michal Hocko <mhocko@suse.com>
To: Rafael Wysocki <rjw@rjwysocki.net>
To: Len Brown <len.brown@intel.com>
To: Bjorn Helgaas <bhelgaas@google.com>
To: Vlastimil Babka <vbabka@suse.cz>
To: Tejun Heo <tj@kernel.org>
To: Lai Jiangshan <jiangshanlai@gmail.com>
To: Thomas Gleixner <tglx@linutronix.de>
To: Fengguang Wu <fengguang.wu@intel.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: linux-pm@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: linux-mm@kvack.org
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Unlike running, the runnable part can't be directly propagated through
the hierarchy when we migrate a task. The main reason is that runnable
time can be shared with other sched_entities that stay on the rq and
this runnable time will also remain on prev cfs_rq and must not be
removed.
Instead, we can estimate what should be the new runnable of the prev
cfs_rq and check that this estimation stay in a possible range. The
prop_runnable_sum is a good estimation when adding runnable_sum but
fails most often when we remove it. Instead, we could use the formula
below instead:
gcfs_rq's runnable_sum = gcfs_rq->avg.load_sum / gcfs_rq->load.weight
which assumes that tasks are equally runnable which is not true but
easy to compute.
Beside these estimates, we have several simple rules that help us to filter
out wrong ones:
- ge->avg.runnable_sum <= than LOAD_AVG_MAX
- ge->avg.runnable_sum >= ge->avg.running_sum (ge->avg.util_sum << LOAD_AVG_MAX)
- ge->avg.runnable_sum can't increase when we detach a task
The effect of these fixes is better cgroups balancing.
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Ben Segall <bsegall@google.com>
Cc: Chris Mason <clm@fb.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yuyang Du <yuyang.du@intel.com>
Link: http://lkml.kernel.org/r/1510842112-21028-1-git-send-email-vincent.guittot@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds
Alexey Dobriyan
Ingo Molnar
Mel Gorman
Wen Yang
Steven Rostedt (VMware)
Peter Zijlstra
Mathieu Desnoyers
Josh Snyder
Juri Lelli
Juri Lelli
Joel Fernandes
Viresh Kumar
Patrick Bellasi
rodrigosiqueira
Randy Dunlap
Sergey Senozhatsky
Cheng Jian
Vincent Guittot