This commit takes ALSA firewire-digi00x driver to perform sequence replay
for media clock recovery.
All of models in Digidesign digi00x family don't transfer isochronous
packets till receiving isochronous packets. The on-the-fly mode is used
for the purpose. They don't interpret presentation time expressed in syt
field of received CIP, therefore the sequence of the number of data blocks
per packet is important for media clock recovery.
The sequence replay is tested with below models:
* Digidesign Digi 002
* Digidesign Digi 002 Rack
* Digidesign Digi 003
* Digidesign Digi 003 Rack
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210531025103.17880-5-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Models in below series start transmission of packet after receiving the
sequence of packets:
* Digidesign Digi00x family
* RME Fireface series
Additionally, models in Tascam FireWire series start multiplexing PCM
frames into packets enough after receiving packets. It's required to
transfer packets on-the-fly for the above models according to nominal
sampling transfer frequency before starting sequence replay.
This commit allows drivers to decide whether the engine transfers packet
on-the-fly or not.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210527122611.173711-4-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In design of audio and music unit in IEEE 1394 bus, feedback of
effective sampling transfer frequency (STF) is delivered by packets
transferred from device. The devices supported by ALSA firewire stack
are categorized to three groups regarding to it.
* Group 1:
* Echo Audio Fireworks board module
* Oxford Semiconductor OXFW971 ASIC
* Digidesign Digi00x family
* Tascam FireWire series
* RME Fireface series
* Group 2:
* BridgeCo. DM1000/DM1100/DM1500 ASICs for BeBoB solution
* TC Applied Technologies DICE ASICs
* Group 3:
* Mark of the Unicord FireWire series
In group 1, the effective STF is determined by the sequence of the number
of events per packet. In group 2, the sequence of presentation timestamp
expressed in syt field of CIP header is interpreted as well. In group 3,
the presentation timestamp is expressed in source packet header (SPH) of
each data block.
I note that some models doesn't take care of effective STF with large
internal buffer. It's reasonable to name it as group 0:
* Group 0
* Oxford Semiconductor OXFW970 ASIC
The effective STF is known to be slightly different from nominal STF for
all of devices, and to be different between the devices. Furthermore, the
effective STF is known to be shifted for long-period transmission. This
makes it hard for software to satisfy the effective STF when processing
packets to the device.
The effective STF is deterministic as a result of analyzing the batch of
packet transferred from the device. For the analysis, caching the sequence
of parameter in the packet is required.
This commit adds an option so that AMDTP domain structure takes AMDTP
stream structure to cache the sequence of parameters in packet transferred
from the device. The parameters are offset ticks of syt field against the
cycle to receive the packet and the number of data blocks per packet.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210527122611.173711-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When starting AMDTP domain, tasks in process context yields running CPU
till all of isochronous context get callback, with an assumption that
it's OK to process content of packet.
However several isochronous cycles are skipped to transfer rx packets, or
the content of rx packets are dropped, to manage the timing to start
processing the packets.
This commit changes the timing for tasks in process context to wake up
when processing content of packet is actually ready.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210520040154.80450-9-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some devices have a quirk to postpone transmission of isoc packet for
several dozen or hundred isoc cycles since configured to transmit.
Furthermore, some devices have a quirk to transmit isoc packet with
discontinued data of its header.
In 1394 OHCI specification, software allows to start isoc context with
certain isoc cycle. Linux firewire subsystem has kernel API to use it
as well.
This commit uses the functionality of 1394 OHCI controller to handle
the quirks. At present, this feature is convenient to ALSA bebob and
fireface driver. As a result, some devices can be safely handled, as
long as I know:
- MAudio FireWire solo
- MAudio ProFire Lightbridge
- MAudio FireWire 410
- Roland FA-66
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191018061911.24909-7-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit allows ALSA firewire-digi00x driver to share PCM buffer
size for both capture and playback PCM substream. When AMDTP domain
starts for one of the PCM substream, buffer size of the PCM substream
is stores to AMDTP domain structure. Some AMDTP streams have already
run with the buffer size when another PCM substream starts, therefore
the PCM substream has a constraint to its buffer size.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191017155424.885-7-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The number of packets in packet buffer has been fixed number (=48) since
first commit of ALSA IEC 61883-1/6 packet streaming engine.
This commit allows the engine to use variable number of packets in the
buffer. The size is calculated by a parameter in AMDTP domain structure
surely to store the number of events in the packets of buffer. Although
the value of parameter is expected to come from 'period size' parameter
of PCM substream, at present 48 is still used.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191017155424.885-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a preparation to share the size of PCM period between
PCM substreams on AMDTP streams in the same domain. At this time,
the size of PCM period in PCM substream which starts AMDTP streams in the
same domain is recorded.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191007110532.30270-7-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a preparation to support AMDTP domain.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a very big update, mainly thanks to Morimoto-san's refactoring
work and some fairly large new drivers.
- Lots more work on moving towards a component based framework from
Morimoto-san.
- Support for force disconnecting muxes from Jerome Brunet.
- New drivers for Cirrus Logic CS47L35, CS47L85 and CS47L90, Conexant
CX2072X, Realtek RT1011 and RT1308.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl0jGwUTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0LD4B/9AkutfS+vznOrk0V0wFb2SUfjwE4Pr
+z/kAehohAOl/7pg9Dun/lmZYBWMyOM2aYmK81ahEo2DfO+uzwkwjCaXFjGVGwEK
j7XpWkrIjKnou/z1FeALgVvt+crzdy5iNWC04AbKaP2WHCcI7zvPQIsBta/V0OJt
lg+j0J7pagnTMcgV1+qJdaASmofy/hpoZ79Gv0PIfGC8hpJ/3mBgcNPCLQrJtD4R
v+tzvCZNrZVqCanwLf3vouEm1bpWYOpI+Wdmu4u6rY7MhmCj72EJ2zyfdm/qtaxF
e7whgCyOQFkWe7NgDn0G08aAT6LsaxOtPNr7H8tL8S8sw8425fqeOouV
=n/HQ
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.3' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v5.3
This is a very big update, mainly thanks to Morimoto-san's refactoring
work and some fairly large new drivers.
- Lots more work on moving towards a component based framework from
Morimoto-san.
- Support for force disconnecting muxes from Jerome Brunet.
- New drivers for Cirrus Logic CS47L35, CS47L85 and CS47L90, Conexant
CX2072X, Realtek RT1011 and RT1308.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
>From callbacks for pcm and rawmidi interfaces, the functions to stop
and release duplex streams are called at the same time. This commit
merges the two functions.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After bus reset, isochronous resource manager releases all of allocated
isochronous resources. The nodes to transfer isochronous packet should
request reallocation of the resources.
However, between the bus-reset and invocation of 'struct fw_driver.update'
handler, ALSA PCM application can detect this situation by XRUN because
the target device cancelled to transmit packets once bus-reset occurs.
Due to the above mechanism, ALSA fireface driver just stops packet
streaming in the update handler, thus pcm.prepare handler should
request the reallocation.
This commit requests the reallocation in pcm.prepare callback when
bus generation is changed.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Once allocated, isochronous resources are available for packet
streaming, even if the streaming is cancelled. For this reason,
current implementation handles allocation of the resources and
starting packet streaming at the same time. However, this brings
complicated procedure to start packet streaming.
This commit separates the allocation and starting. The allocation is
done in pcm.hw_params callback and available till pcm.hw_free callback.
Even if any XRUN occurs, pcm.prepare callback is done to restart
packet streaming without releasing/allocating the resources.
There are two points to stop packet streaming; in pcm.hw_params and
pcm.prepare callbacks. The former point is a case that packet streaming
is already started for any MIDI substream then packet streaming is
requested with different sampling transfer frequency for any PCM
substream. The latter point is cases of any XRUN or packet queueing
error.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a part of preparation to perform allocation/release
of isochronous resources in pcm.hw_params/hw_free callbacks.
All of models in Digidesign Digi00x family have the same formation of
data channels in isochronous packet for both directions. This commit
simplifies allocation of isochronous resources in this point.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a part of preparation to perform allocation/release
of isochronous resources in pcm.hw_params/hw_free callbacks.
The caller of begin_session() calls finish_session() in its error path,
thus no need to call finish_session() in error path of begin_session().
This commit simplifies error path of begin_session().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a part of preparation to perform allocation/release
of isochronous resources in pcm.hw_params/hw_free callbacks.
The operation to finish packet streaming corresponds to stopping
isochronous contexts. This commit applies code refactoring to
move codes to stop into a helper function to finish the session.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a part of preparation to perform allocation/release
of isochronous resources in pcm.hw_params/hw_free callbacks.
The registration of isochronous channels is done just after allocation
of isochronous resources. This commit separates the registration just
before starting packet streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Based on 1 normalized pattern(s):
licensed under the terms of the gnu general public license version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 88 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000437.521539229@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds MIDI functionality to capture/playback MIDI messages
from/to physical MIDI ports. These messages are transferred in isochronous
packets.
When no substreams request AMDTP streams to run, this driver starts the
streams at current sampling rate. When other substreams start at different
sampling rate, the streams are stopped temporarily, then start again at
requested sampling rate. This operation can generate missing MIDI bytes,
thus it's preferable to start PCM substreams at favorite sampling rate in
advance.
Digi 002/003 console also has a set of MIDI port for physical controls.
These ports are added in later commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In Digi 002/003 protocol, MIDI messages are transferred in the last data
channel of data blocks. Although this data channel has a label of 0x80,
it's not fully MIDI conformant data channel especially because the Counter
field always zero independently of included MIDI bytes. The 4th byte of
the data channel in LSB tells the number of included MIDI bytes. This byte
also includes the number of MIDI port. Therefore, the data format in this
data channel is:
* 1st: 0x80 as label
* 2nd: MIDI bytes
* 3rd: 0 or MIDI bytes
* 4th: the number of MIDI byte and the number of MIDI port
This commit adds support of MIDI messages in data block processing layer.
Like AM824 data format, this data channel has a capability to transfer
more MIDI messages than the capability of phisical MIDI bus. Therefore, a
throttle for data rate is required to prevent devices' internal buffer to
overflow.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds hwdep interface so as the other sound drivers for units
on IEEE 1394 bus have.
This interface is designed for mixer/control applications. By using this
interface, an application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a functionality to manage streaming.
The streaming is not controlled by CMP in IEC 61883-6. It's controlled by
IEEE 1394 write transaction to certain addresses.
Several clock sources are available, while there're no differences about
packet transmission. The value of SYT field in transmitted packets is
always zero. Thus, streams in both direction don't build synchronization.
And the device always requires received packets to transmit packets. This
driver keeps to transfer outgoing stream even if they're not required.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Sakamoto
Takashi Iwai
Thomas Gleixner