The .to_irq() function obviously takes the per-chip offset
as parameter, not the global GPIO number.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These drivers are GPIO drivers, and the do not need to use the
legacy header in <linux/gpio.h>, go directly for
<linux/gpio/driver.h> instead.
Replace any use of GPIOF_* with 0/1, these flags are for
consumers, not drivers.
Get rid of a few gpio_to_irq() users that was littering
around the place, use local callbacks or avoid using it at
all.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is harmless, but "val" isn't necessarily initialized if
abx500_get_register_interruptible() fails. I've re-arranged the code to
just return an error code in that situation.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The U8540 was an evolved version of the U8500, but it was never
mass produced or put into products, only reference designs exist.
The upstream support was never completed and it is unlikely that
this will happen so drop the support for now to simplify
maintenance of the U8500.
Cc: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The MUSB block in the Nomadik has two pin settings: high speed or
full speed. These correspond to two unique pin group settings: all
pins set to function B for high speed and all set to function C
for full speed. Full speed uses more pins than high speed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A single character (line break) should be put into a sequence.
Thus use the corresponding function "seq_putc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
CORE:
- Fix the semantics of raw GPIO to actually be raw. No
inversion semantics as before, but also no open draining,
and allow the raw operations to affect lines used for
interrupts as the caller supposedly knows what they are
doing if they are getting the big hammer.
- Rewrote the __inner_function() notation calls to names that
make more sense. I just find this kind of code disturbing.
- Drop the .irq_base() field from the gpiochip since now all
IRQs are mapped dynamically. This is nice.
- Support for .get_multiple() in the core driver API. This
allows us to read several GPIO lines with a single
register read. This has high value for some usecases: it
can be used to create oscilloscopes and signal analyzers
and other things that rely on reading several lines at
exactly the same instant. Also a generally nice
optimization. This uses the new assign_bit() macro from
the bitops lib that was ACKed by Andrew Morton and
is implemented for two drivers, one of them being the
generic MMIO driver so everyone using that will be able
to benefit from this.
- Do not allow requests of Open Drain and Open Source
setting of a GPIO line simultaneously. If the hardware
actually supports enabling both at the same time the
electrical result would be disastrous.
- A new interrupt chip core helper. This will be helpful
to deal with "banked" GPIOs, which means GPIO controllers
with several logical blocks of GPIO inside them. This
is several gpiochips per device in the device model, in
contrast to the case when there is a 1-to-1 relationship
between a device and a gpiochip.
NEW DRIVERS:
- Maxim MAX3191x industrial serializer, a very interesting
piece of professional I/O hardware.
- Uniphier GPIO driver. This is the GPIO block from the
recent Socionext (ex Fujitsu and Panasonic) platform.
- Tegra 186 driver. This is based on the new banked GPIO
infrastructure.
OTHER IMPROVEMENTS:
- Some documentation improvements.
- Wakeup support for the DesignWare DWAPB GPIO controller.
- Reset line support on the DesignWare DWAPB GPIO controller.
- Several non-critical bug fixes and improvements for the
Broadcom BRCMSTB driver.
- Misc non-critical bug fixes like exotic errorpaths, removal
of dead code etc.
- Explicit comments on fall-through switch() statements.
-----BEGIN PGP SIGNATURE-----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=8Mon
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.15 kernel cycle:
Core:
- Fix the semantics of raw GPIO to actually be raw. No inversion
semantics as before, but also no open draining, and allow the raw
operations to affect lines used for interrupts as the caller
supposedly knows what they are doing if they are getting the big
hammer.
- Rewrote the __inner_function() notation calls to names that make
more sense. I just find this kind of code disturbing.
- Drop the .irq_base() field from the gpiochip since now all IRQs are
mapped dynamically. This is nice.
- Support for .get_multiple() in the core driver API. This allows us
to read several GPIO lines with a single register read. This has
high value for some usecases: it can be used to create
oscilloscopes and signal analyzers and other things that rely on
reading several lines at exactly the same instant. Also a generally
nice optimization. This uses the new assign_bit() macro from the
bitops lib that was ACKed by Andrew Morton and is implemented for
two drivers, one of them being the generic MMIO driver so everyone
using that will be able to benefit from this.
- Do not allow requests of Open Drain and Open Source setting of a
GPIO line simultaneously. If the hardware actually supports
enabling both at the same time the electrical result would be
disastrous.
- A new interrupt chip core helper. This will be helpful to deal with
"banked" GPIOs, which means GPIO controllers with several logical
blocks of GPIO inside them. This is several gpiochips per device in
the device model, in contrast to the case when there is a 1-to-1
relationship between a device and a gpiochip.
New drivers:
- Maxim MAX3191x industrial serializer, a very interesting piece of
professional I/O hardware.
- Uniphier GPIO driver. This is the GPIO block from the recent
Socionext (ex Fujitsu and Panasonic) platform.
- Tegra 186 driver. This is based on the new banked GPIO
infrastructure.
Other improvements:
- Some documentation improvements.
- Wakeup support for the DesignWare DWAPB GPIO controller.
- Reset line support on the DesignWare DWAPB GPIO controller.
- Several non-critical bug fixes and improvements for the Broadcom
BRCMSTB driver.
- Misc non-critical bug fixes like exotic errorpaths, removal of dead
code etc.
- Explicit comments on fall-through switch() statements"
* tag 'gpio-v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (65 commits)
gpio: tegra186: Remove tegra186_gpio_lock_class
gpio: rcar: Add r8a77995 (R-Car D3) support
pinctrl: bcm2835: Fix some merge fallout
gpio: Fix undefined lock_dep_class
gpio: Automatically add lockdep keys
gpio: Introduce struct gpio_irq_chip.first
gpio: Disambiguate struct gpio_irq_chip.nested
gpio: Add Tegra186 support
gpio: Export gpiochip_irq_{map,unmap}()
gpio: Implement tighter IRQ chip integration
gpio: Move lock_key into struct gpio_irq_chip
gpio: Move irq_valid_mask into struct gpio_irq_chip
gpio: Move irq_nested into struct gpio_irq_chip
gpio: Move irq_chained_parent to struct gpio_irq_chip
gpio: Move irq_default_type to struct gpio_irq_chip
gpio: Move irq_handler to struct gpio_irq_chip
gpio: Move irqdomain into struct gpio_irq_chip
gpio: Move irqchip into struct gpio_irq_chip
gpio: Introduce struct gpio_irq_chip
pinctrl: armada-37xx: remove unused variable
...
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure is only used to copy into another structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
17545 5376 0 22921 5989 drivers/pinctrl/nomadik/pinctrl-abx500.o
after:
bss dec hex filename
17273 5320 0 22593 5841 drivers/pinctrl/nomadik/pinctrl-abx500.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no point in adding any default trigger for these
GPIO interrupts: the device tree should contain all trigger
information and the platforms using the driver boots
exclusively from device tree.
Also the boot log is nagging me to fix this:
[ 0.771057] ------------[ cut here ]------------
[ 0.775695] WARNING: CPU: 0 PID: 1 at
../drivers/gpio/gpiolib.c:1622 _gpiochip_irqchip_add+0x138/0x160
[ 0.785034] /soc/gpio@8012e000: Ignoring 2 default trigger
(...)
[ 0.942962] gpio 8012e000.gpio: at address e08f8000
(etc ad nauseam)
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/nomadik/Kconfig:config PINCTRL_NOMADIK
drivers/pinctrl/nomadik/Kconfig: bool "Nomadik pin controller driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
config PINCTRL_ABX500
bool "ST-Ericsson ABx500 family Mixed Signal Circuit gpio functions"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
Note that MODULE_ALIAS is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use of_property_read_bool to check for the existence of a property.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2,x;
@@
- if (of_get_property(e1,e2,NULL))
- x = true;
- else
- x = false;
+ x = of_property_read_bool(e1,e2);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
New drivers:
- New driver for Oxnas pin control and GPIO. This ARM-based chipset
is used in a few storage (NAS) type devices.
- New driver for the MAX77620/MAX20024 pin controller portions.
- New driver for the Intel Merrifield pin controller.
New subdrivers:
- New subdriver for the Qualcomm MDM9615
- New subdriver for the STM32F746 MCU
- New subdriver for the Broadcom NSP SoC.
Cleanups:
- Demodularization of bool compiled-in drivers.
Apart from this there is just regular incremental improvements to
a lot of drivers, especially Uniphier and PFC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=po0g
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.8 kernel cycle.
Nothing stands out as especially exiting: new drivers, new subdrivers,
lots of cleanups and incremental features.
Business as usual.
New drivers:
- New driver for Oxnas pin control and GPIO. This ARM-based chipset
is used in a few storage (NAS) type devices.
- New driver for the MAX77620/MAX20024 pin controller portions.
- New driver for the Intel Merrifield pin controller.
New subdrivers:
- New subdriver for the Qualcomm MDM9615
- New subdriver for the STM32F746 MCU
- New subdriver for the Broadcom NSP SoC.
Cleanups:
- Demodularization of bool compiled-in drivers.
Apart from this there is just regular incremental improvements to a
lot of drivers, especially Uniphier and PFC"
* tag 'pinctrl-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (131 commits)
pinctrl: fix pincontrol definition for marvell
pinctrl: xway: fix typo
Revert "pinctrl: amd: make it explicitly non-modular"
pinctrl: iproc: Add NSP and Stingray GPIO support
pinctrl: Update iProc GPIO DT bindings
pinctrl: bcm: add OF dependencies
pinctrl: ns2: remove redundant dev_err call in ns2_pinmux_probe()
pinctrl: Add STM32F746 MCU support
pinctrl: intel: Protect set wake flow by spin lock
pinctrl: nsp: remove redundant dev_err call in nsp_pinmux_probe()
pinctrl: uniphier: add Ethernet pin-mux settings
sh-pfc: Use PTR_ERR_OR_ZERO() to simplify the code
pinctrl: ns2: fix return value check in ns2_pinmux_probe()
pinctrl: qcom: update DT bindings with ebi2 groups
pinctrl: qcom: establish proper EBI2 pin groups
pinctrl: imx21: Remove the MODULE_DEVICE_TABLE() macro
Documentation: dt: Add new compatible to STM32 pinctrl driver bindings
includes: dt-bindings: Add STM32F746 pinctrl DT bindings
pinctrl: sunxi: fix nand0 function name for sun8i
pinctrl: uniphier: remove pointless pin-mux settings for PH1-LD11
...
There are five functions in the driver that are defined but
only used locally. Since these are not used in the current
kernel, delete them to avoid the following warnings:
drivers/pinctrl/nomadik/pinctrl-nomadik.c:1036:6: warning: symbol 'nmk_gpio_clocks_enable' was not declared. Should it be static?
drivers/pinctrl/nomadik/pinctrl-nomadik.c:1050:6: warning: symbol 'nmk_gpio_clocks_disable' was not declared. Should it be static?
drivers/pinctrl/nomadik/pinctrl-nomadik.c:1073:6: warning: symbol 'nmk_gpio_wakeups_suspend' was not declared. Should it be static?
drivers/pinctrl/nomadik/pinctrl-nomadik.c:1094:6: warning: symbol 'nmk_gpio_wakeups_resume' was not declared. Should it be static?
drivers/pinctrl/nomadik/pinctrl-nomadik.c:1120:6: warning: symbol 'nmk_gpio_read_pull' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The input/output directions were inversed on the GPIO direction
read function. Loose a ! and it is correct.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Add the devm_pinctrl_register() API and switch all applicable drivers
to use it, saving lots of lines of code all over the place.
New drivers:
- New driver for the Broadcom NS2 SoC.
- New subdriver for the PXA25x SoCs.
- New subdriver for the AMLogic Meson GXBB SoC.
Driver improvements:
- The Intel Baytrail driver now properly supports pin control.
- The Nomadik, Rockchip, Broadcom BCM2835 supports the .get_direction() callback in
the GPIO portions.
- Continued development and stabilization of several SH-PFC
SoC subdrivers: r8a7795, r8a7790, r8a7794 etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXPZ9PAAoJEEEQszewGV1zboIQALtGX/tyKFzaOsj7WxHHjmfb
yufqU62NE0sPT6/hzUY3a1U9dpakbMehBXy0go0vcShmPSznX2glFv4GR6LEeE0+
o0JNv0d13f2s5WPEqn6L/ePuSuNNjfkwjZ7YJlAXx/WqAWI9c70H8/VHsXEObWOe
ZsAZx2FdUFDOxugDWsCmU6kt7RXbqTzEz2M/dDANr4B2cRH/3yny797P2y9tLy3w
Rqsdqw1C1A9SICSIRZ+YBWctXhRq5APsB75IncUYIQJF5hXoAcBCp6v+cNZHpXOw
X9J+zKDeMjOSsVvOyHA+4P+vPYgkOPl9GuUVJRvnbfCZYKEhDM1e5F393Cf7gYYz
dIEAzIFlPmZCMxog7AWEA0yDp2rJ2W/5WoN7pg+a5cKSHgriIry1sxDslBD2b9ZW
XxdVm4pMOiVw6yokHI4g2hcDsZOEW8zhPQi1wPuVuJ3k1m7T/d13mFAFTSWwOLVx
WFDLuD20ybkCVmxEs0ePrDzLcgEnxW40src6lqSzIx8bUBCH+iWPkIPH0fAJ6bNK
TFtfcCFrtE2YmpxrCgZceTLER/7jAGkXFegbJq1epNmz7+0wbEbRxcVFE1IbYUBW
ejslgTtLDvnzzkR7UISZF/Qna066tCGT52sEA82ZcrqytGkSTLB4kUDkQvXaCB0r
4DLJ47K32mQu3MrOPLjE
=tlvn
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This kernel cycle was quite calm when it comes to pin control and
there is really just one major change, and that is the introduction of
devm_pinctrl_register() managed resources.
Apart from that linear development, details below.
Core changes:
- Add the devm_pinctrl_register() API and switch all applicable
drivers to use it, saving lots of lines of code all over the place.
New drivers:
- driver for the Broadcom NS2 SoC
- subdriver for the PXA25x SoCs
- subdriver for the AMLogic Meson GXBB SoC
Driver improvements:
- the Intel Baytrail driver now properly supports pin control
- Nomadik, Rockchip, Broadcom BCM2835 support the .get_direction()
callback in the GPIO portions
- continued development and stabilization of several SH-PFC SoC
subdrivers: r8a7795, r8a7790, r8a7794 etc"
* tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (85 commits)
Revert "pinctrl: tegra: avoid parked_reg and parked_bank"
pinctrl: meson: Fix eth_tx_en bit index
pinctrl: tegra: avoid parked_reg and parked_bank
pinctrl: tegra: Correctly check the supported configuration
pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC
pinctrl: rockchip: fix pull setting error for rk3399
pinctrl: stm32: Implement .pin_config_dbg_show()
pinctrl: nomadik: hide nmk_gpio_get_mode when unused
pinctrl: ns2: rename pinctrl_utils_dt_free_map
pinctrl: at91: Merge clk_prepare and clk_enable into clk_prepare_enable
pinctrl: at91: Make at91_gpio_template const
pinctrl: baytrail: fix some error handling in debugfs
pinctrl: ns2: add pinmux driver support for Broadcom NS2 SoC
pinctrl: sirf/atlas7: trivial fix of spelling mistake on flagged
pinctrl: sh-pfc: Kill unused variable in sh_pfc_remove()
pinctrl: nomadik: implement .get_direction()
pinctrl: nomadik: use BIT() with offsets consequently
pinctrl: exynos5440: Use off-stack memory for pinctrl_gpio_range
pinctrl: zynq: Use devm_pinctrl_register() for pinctrl registration
pinctrl: u300: Use devm_pinctrl_register() for pinctrl registration
...
nmk_gpio_get_mode is only used in one place, and that is conditionally
compiled if DEBUG_FS is enabled. A recent cleanup has marked the
definition 'static', which now leads to a warning:
drivers/pinctrl/nomadik/pinctrl-nomadik.c:614:12: error: 'nmk_gpio_get_mode' defined but not used [-Werror=unused-function]
static int nmk_gpio_get_mode(struct nmk_gpio_chip *nmk_chip, int offset)
^~~~~~~~~~~~~~~~~
Moving the function itself inside the #ifdef shuts it up again.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 5e81e0a091 ("pinctrl: nomadik: use BIT() with offsets consequently")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver is confusing in referencing/dereferencing the global
GPIO number scope in some places and using local offsets in other
places. Remove some of the confusion by removing local "bit" and
"bitmask" definitions and just use BIT(offset) directly. Also
unexport a function only used in this file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename pinctrl_utils_dt_free_map to pinctrl_utils_free_map, since
it does not depend on device tree despite the current name. This
will enforce a consistent naming in pinctr-utils.c and will make
it clear it can be called from outside device tree (e.g. from
ACPI handling code).
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull up was reported as pull down and vice versa. Fix this.
Fixes: 8f1774a2a9 "pinctrl: nomadik: improve GPIO debug prints"
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The STn8815 has 22 dedicated pins for CLCD with up to 16 bits
in parallel, but pins 32 thru 39 can be used for an additional
CLCD signal lines 16 thru 23.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The nomadik pinctrl driver has two functions that are only used
for debugfs output and are otherwise unused:
drivers/pinctrl/nomadik/pinctrl-abx500.c:194:12: error: 'abx500_get_pull_updown' defined but not used
drivers/pinctrl/nomadik/pinctrl-abx500.c:471:12: error: 'abx500_get_mode' defined but not used
This makes the function definitions conditional to avoid the
harmless warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The name .dev in a struct is normally reserved for a struct device
that is let us say a superclass to the thing described by the struct.
struct gpio_chip stands out by confusingly using a struct device *dev
to point to the parent device (such as a platform_device) that
represents the hardware. As we want to give gpio_chip:s real devices,
this is not working. We need to rename this member to parent.
This was done by two coccinelle scripts, I guess it is possible to
combine them into one, but I don't know such stuff. They look like
this:
@@
struct gpio_chip *var;
@@
-var->dev
+var->parent
and:
@@
struct gpio_chip var;
@@
-var.dev
+var.parent
and:
@@
struct bgpio_chip *var;
@@
-var->gc.dev
+var->gc.parent
Plus a few instances of bgpio that I couldn't figure out how
to teach Coccinelle to rewrite.
This patch hits all over the place, but I *strongly* prefer this
solution to any piecemal approaches that just exercise patch
mechanics all over the place. It mainly hits drivers/gpio and
drivers/pinctrl which is my own backyard anyway.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace all trivial request/free callbacks that do nothing but call into
pinctrl code with the generic versions.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
cycle
Core changes:
- It is possible configure groups in debugfs.
- Consolidation of chained IRQ handler install/remove replacing
all call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a
combined call to irq_set_chained_handler_and_data(). This
series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which
is way cleaner.
- Tglx also wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs
from IRQ numbers. The goal is to get rid of the irq number
from the handlers in the IRQ flow which is nice.
Driver feature enhancements:
- Power management support for the SiRF SoC Atlas 7.
- Power down support for the Qualcomm driver.
- Intel Cherryview and Baytrail: switch drivers to use raw
spinlocks in IRQ handlers to play nice with the realtime
patch set.
- Rework and new modes handling for Qualcomm SPMI-MPP.
- Pinconf power source config for SH PFC.
New drivers and subdrivers:
- A new driver for Conexant Digicolor CX92755.
- A new driver for UniPhier PH1-LD4, PH1-Pro4, PH1-sLD8,
PH1-Pro5, ProXtream2 and PH1-LD6b SoC pin control support.
- Reverse-egineered the S/PDIF settings for the Allwinner
sun4i driver.
- Support for Qualcomm Technologies QDF2xxx ARM64 SoCs
- A new Freescale i.mx6ul subdriver.
Cleanup:
- Remove platform data support in a number of SH PFC
subdrivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4QFX
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.3 development
cycle.
Like with GPIO it's a lot of stuff. If my subsystems are any sign of
the overall tempo of the kernel v4.3 will be a gigantic diff.
[ It looks like 4.3 is calmer than 4.2 in most other subsystems, but
we'll see - Linus ]
Core changes:
- It is possible configure groups in debugfs.
- Consolidation of chained IRQ handler install/remove replacing all
call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a combined
call to irq_set_chained_handler_and_data(). This series was
created by Thomas Gleixner after the problem was observed by
Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which is
way cleaner.
- Tglx also wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs from
IRQ numbers. The goal is to get rid of the irq number from the
handlers in the IRQ flow which is nice.
Driver feature enhancements:
- Power management support for the SiRF SoC Atlas 7.
- Power down support for the Qualcomm driver.
- Intel Cherryview and Baytrail: switch drivers to use raw spinlocks
in IRQ handlers to play nice with the realtime patch set.
- Rework and new modes handling for Qualcomm SPMI-MPP.
- Pinconf power source config for SH PFC.
New drivers and subdrivers:
- A new driver for Conexant Digicolor CX92755.
- A new driver for UniPhier PH1-LD4, PH1-Pro4, PH1-sLD8, PH1-Pro5,
ProXtream2 and PH1-LD6b SoC pin control support.
- Reverse-egineered the S/PDIF settings for the Allwinner sun4i
driver.
- Support for Qualcomm Technologies QDF2xxx ARM64 SoCs
- A new Freescale i.mx6ul subdriver.
Cleanup:
- Remove platform data support in a number of SH PFC subdrivers"
* tag 'pinctrl-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (95 commits)
pinctrl: at91: fix null pointer dereference
pinctrl: mediatek: Implement wake handler and suspend resume
pinctrl: mediatek: Fix multiple registration issue.
pinctrl: sh-pfc: r8a7794: add USB pin groups
pinctrl: at91: Use generic irq_{request,release}_resources()
pinctrl: cherryview: Use raw_spinlock for locking
pinctrl: baytrail: Use raw_spinlock for locking
pinctrl: imx6ul: Remove .owner field
pinctrl: zynq: Fix typos in smc0_nand_grp and smc0_nor_grp
pinctrl: sh-pfc: Implement pinconf power-source param for voltage switching
clk: rockchip: add pclk_pd_pmu to the list of rk3288 critical clocks
pinctrl: sun4i: add spdif to pin description.
pinctrl: atlas7: clear ugly branch statements for pull and drivestrength
pinctrl: baytrail: Serialize all register access
pinctrl: baytrail: Drop FSF mailing address
pinctrl: rockchip: only enable gpio clock when it setting
pinctrl/mediatek: fix spelling mistake in dev_err error message
pinctrl: cherryview: Serialize all register access
pinctrl: UniPhier: PH1-Pro5: add I2C ch6 pin-mux setting
pinctrl: nomadik: reflect current input value
...
Split the UART pin groups so we can activate RX/TX, CTS/RTS and
the modem pins (DCD, DSR, RI, DTR) as three different groups
with function u0.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We no longer have to do GPIO initialization before the
pinctrl initialization, instead we can initialize the pinctrl
portions of the driver first and then the GPIO. Thus we can
move GPIO initialization to a subsystem_initcall(), but
not yet to a device_initcall().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This gets the GPIO ranges out of the driver and into the device
tree where they belong. Standard DT bindings already exist for
this. Since no systems with this are deployed we can just augment
all device trees and the drivers at the same time and simplify
the world.
This also defines the array of GPIO chips related to the pin
controller.
Cc: arm@kernel.org
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the pin controller probes before the GPIO driver it needs to
populate the GPIO driver state containers ahead of the actual
driver probe as the addresses are used by both halves of the
driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of indexing around the GPIO ranges to find a chip, look directly
in the local array of state containers for nmk_gpio_chip:s.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Break out the function that allocates the nomadik GPIO chip state
container to its own function.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit a21763a0b1
"pinctrl: nomadik: activate strict mux mode"
put all Nomadik pin controllers to strict mode. This was
not good on the Snowball platform: the muxing of GPIOs to
different pins is done with hogs in the DTS file, and then
these GPIOs are used by offset, relying on hogs to mux the
pins. Since that means the pin controller "owns" the pins
and at the same time we have a GPIO user, this pin controller
is by definition not strict.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use irq_desc_get_xxx() to avoid redundant lookup of irq_desc while we
already have a pointer to corresponding irq_desc.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Currently, pinctrl_register() just returns NULL on error, so the
callers can not know the exact reason of the failure.
Some of the pinctrl drivers return -EINVAL, some -ENODEV, and some
-ENOMEM on error of pinctrl_register(), although the error code
might be different from the real cause of the error.
This commit reworks pinctrl_register() to return the appropriate
error code and modifies all of the pinctrl drivers to use IS_ERR()
for the error checking and PTR_ERR() for getting the error code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Ray Jui <rjui@broadcom.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Acked-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Assign GPIO chip and irqchip to the GPIO container dynamically,
so we can set a unique name for each GPIO irqchip and see what
chip the hwirq offset actually relates to.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij
Rob Herring
Dan Carpenter
Markus Elfring
Linus Torvalds
Thierry Reding
Greg Kroah-Hartman
Masahiro Yamada
Gustavo A. R. Silva
Paul Gortmaker
Julia Lawall
Ben Dooks
Arnd Bergmann
Laxman Dewangan
Irina Tirdea
Jonas Gorski
Thomas Gleixner
Jiang Liu
Geert Uytterhoeven