mv_init_host() propagates the value returned by mv_chip_id() which in turn
gets propagated by mv_pci_init_one() and hits local_pci_probe().
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Since this is a bug rather than a recoverable runtime error we should
use dev_alert() instead of dev_err().
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
The function mv_platform_probe() neglects to check the results of the
calls to platform_get_irq() and irq_of_parse_and_map() and blithely
passes them to ata_host_activate() -- while the latter only checks
for IRQ0 (treating it as a polling mode indicattion) and passes the
negative values to devm_request_irq() causing it to fail as it takes
unsigned values for the IRQ #...
Add to mv_platform_probe() the proper IRQ checks to pass the positive IRQ
#s to ata_host_activate(), propagate upstream the negative error codes,
and override the IRQ0 with -EINVAL (as we don't want the polling mode).
Fixes: f351b2d638 ("sata_mv: Support SoC controllers")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Link: https://lore.kernel.org/r/51436f00-27a1-e20b-c21b-0e817e0a7c86@omprussia.ru
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fixes the following W=1 kernel build warning(s):
drivers/ata/sata_mv.c:1929: warning: expecting prototype for mv_bmdma_stop(). Prototype was for mv_bmdma_stop_ap() instead
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mark Lord <mlord@pobox.com>
Cc: ALWAYS copy <linux-ide@vger.kernel.org>
Cc: linux-ide@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210318085150.3131936-14-lee.jones@linaro.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fixes the following W=1 kernel build warning(s):
drivers/ata/sata_mv.c:1162: warning: Function parameter or member 'ap' not described in 'mv_start_edma'
drivers/ata/sata_mv.c:1162: warning: Function parameter or member 'port_mmio' not described in 'mv_start_edma'
drivers/ata/sata_mv.c:1162: warning: Function parameter or member 'protocol' not described in 'mv_start_edma'
drivers/ata/sata_mv.c:1162: warning: Excess function parameter 'base' description in 'mv_start_edma'
drivers/ata/sata_mv.c:1535: warning: Function parameter or member 'enable_bmdma' not described in 'mv_bmdma_enable_iie'
drivers/ata/sata_mv.c:1535: warning: expecting prototype for mv_bmdma_enable(). Prototype was for mv_bmdma_enable_iie() instead
drivers/ata/sata_mv.c:1930: warning: Function parameter or member 'ap' not described in 'mv_bmdma_stop_ap'
drivers/ata/sata_mv.c:1930: warning: expecting prototype for mv_bmdma_stop(). Prototype was for mv_bmdma_stop_ap() instead
drivers/ata/sata_mv.c:2228: warning: Function parameter or member 'ap' not described in 'mv_send_fis'
drivers/ata/sata_mv.c:3263: warning: Function parameter or member 'hpriv' not described in 'mv6_reset_hc'
drivers/ata/sata_mv.c:3263: warning: Function parameter or member 'n_hc' not described in 'mv6_reset_hc'
drivers/ata/sata_mv.c:3541: warning: Function parameter or member 'hpriv' not described in 'soc_is_65n'
drivers/ata/sata_mv.c:3541: warning: expecting prototype for soc_is_65(). Prototype was for soc_is_65n() instead
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mark Lord <mlord@pobox.com>
Cc: ALWAYS copy <linux-ide@vger.kernel.org>
Cc: linux-ide@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
ata_qc_complete_multiple() is called with a mask of the still active
tags.
mv_sata doesn't have this information directly and instead calculates
the still active tags from the started tags (ap->qc_active) and the
finished tags as (ap->qc_active ^ done_mask)
Since 28361c4036 the hw_tag and tag are no longer the same and the
equation is no longer valid. In ata_exec_internal_sg() ap->qc_active is
initialized as 1ULL << ATA_TAG_INTERNAL, but in hardware tag 0 is
started and this will be in done_mask on completion. ap->qc_active ^
done_mask becomes 0x100000000 ^ 0x1 = 0x100000001 and thus tag 0 used as
the internal tag will never be reported as completed.
This is fixed by introducing ata_qc_get_active() which returns the
active hardware tags and calling it where appropriate.
This is tested on mv_sata, but sata_fsl and sata_nv suffer from the same
problem. There is another case in sata_nv that most likely needs fixing
as well, but this looks a little different, so I wasn't confident enough
to change that.
Fixes: 28361c4036 ("libata: add extra internal command")
Cc: stable@vger.kernel.org
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add missing export of ata_qc_get_active(), as per Pali.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In case a driver wants to return an error from qc_prep, return enum
ata_completion_errors. sata_mv is one of those drivers -- see the next
patch. Other drivers return the newly defined AC_ERR_OK.
[v2] use enum ata_completion_errors and AC_ERR_OK.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-ide@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use the dma_set_mask_and_coherent helper to set the DMA mask. Rely
on the relatively recent change that setting a larger than required
mask will never fail to avoid the need for the boilerplate 32-bit
fallback code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 59 temple place suite 330 boston ma 02111
1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 83 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.021731668@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is in preparation for allowing full usage of the tag space,
which means that our reserved error handling command will be
using an internal tag value of 32. This doesn't fit in a u32, so
move to a u64.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Tejun Heo <tj@kernel.org>
Anything that goes to the hardware should use ->hw_tag, anything
related to internal lookup should be using ->tag.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Tejun Heo <tj@kernel.org>
After checking all possible call chains to mv_reset_channel here,
my tool finds that mv_reset_channel is never called in atomic context,
namely never in an interrupt handler or holding a spinlock.
Thus mdelay can be replaced with usleep_range to avoid busy wait.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
In cases where a "drop through" comment was already in place, I replaced
it with a proper "fall through" comment, which is what GCC is expecting
to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The pointer ehi is being assigned to a value that is never read
and is redundant. Clean up the code and move the ehi declaration
and initialization to the code block where it is used. Cleans up
clang warning: Value stored to 'ehi' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This reverts commit 368e5fbdfc.
devm_ioremap_resource() enforces that there are no overlapping
resources, where as devm_ioremap() does not. The sata phy driver needs
a subset of the sata IO address space, so maps some of the sata
address space. As a result, sata_mv now fails to probe, reporting it
cannot get its resources, and so we don't have any SATA disks.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Tejun Heo <tj@kernel.org>
Declare of_device_id structures as const as they are either passed to
the macro MODULE_DEVICE_TABLE or stored in the of_match_table field of a
device_driver structure. This field is of type const, so of_device_id
structures having this property can be made const too.
Cross compiled the files drivers/ata/pata_macio.c and
drivers/ata/pata_mpc52xx.c for powerpc architecture.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Convert to devm_ioremap_resource() which provides more consistent error
handling.
Note that devm_ioremap_resource() provides its own error messages.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Here, If devm_ioremap will fail. It will return NULL.
Then hpriv->base = NULL - 0x20000; Kernel can run into
a NULL-pointer dereference. This error check will avoid
NULL pointer dereference.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
If the nr-ports property is missing ata_host_alloc_pinfo is called with
n_ports = 0. This results in host->ports[0] = NULL which later makes
mv_init_host() oops when dereferencing this pointer.
Instead be a bit more cooperative and fail the probing with an error
message.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Replacing dma_pool_alloc and memset with a single call to dma_pool_zalloc
Signed-off-by: Harman Kalra <harman4linux@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fix the signed issue in mv_write_cached_reg() where the laddr
is assigned from a (long)addr instead of (unsigned long)addr.
Fixes the following warnings:
drivers/ata/sata_mv.c:989:26: warning: cast removes address space of expression
drivers/ata/sata_mv.c:989:26: warning: cast removes address space of expression
drivers/ata/sata_mv.c:989:26: warning: cast removes address space of expression
drivers/ata/sata_mv.c:989:26: warning: cast removes address space of expression
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit 9013d64e66 ("ata: sata_mv: fix disk hotplug for Armada
370/XP SoCs") added some manipulation of the LP_PHY_CTL register, but
using magic values. This commit changes the code to use proper
definitions for the LP_PHY_CTL register, which allows to document what
the different bits are doing.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
The phy_power_off() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch fixes host drivers to use CONFIG_PM_SLEEP instead of CONFIG_PM
where applicable. Benefits of this change:
* unused code is not being compiled in for CONFIG_PM=y, CONFIG_PM_SLEEP=n
and CONFIG_PM_RUNTIME=y configurations
* easier transition to use struct dev_pm_ops and SIMPLE_DEV_PM_OPS() in
the future
* more consistent code (there are host drivers which are using the correct
CONFIG_PM_SLEEP checks already)
The patch leaves the core libata code and ->port_[suspend,resume] support
in sata_[inic162x,nv,sil24].c alone for now.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata fixes from Tejun Heo:
"Various device specific fixes. Nothing too interesting"
* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: disable NCQ on Samsung pci-e SSDs on macbooks
ata: sata_mv: Cleanup only the initialized ports
sata_sil: apply MOD15WRITE quirk to TOSHIBA MK2561GSYN
ata: enable quirk from jmicron JMB350 for JMB394
ATA: SATA_MV: Add missing Kconfig select statememnt
ata: pata_imx: Check the return value from clk_prepare_enable()
When an error occurs in the port initialization loop, currently the
driver tries to cleanup all the ports. This results in a NULL pointer
dereference if the ports were only partially initialized.
Fix this by updating only the number of initialized ports (either
with failure or successfully), before jumping to the error path
and looping over that number in the cleanup loop.
Cc: Andrew Lunn <andrew@lunn.ch>
Reported-by: Mikael Pettersson <mikpelinux@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Make use of devm_phy_optional_get() in order to fix probe failures on
Armada 370, XP and others, when there is no phy driver available.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Some Marvell SoCs have a SATA PHY which can be powered off, in order
to save power. Make use of the generic phy framework to control these
phys.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Tejun Heo <tj@kernel.org>
On Armada 370/XP SoCs, once a disk is removed from a SATA port, then the
re-plug events are not detected by the sata_mv driver. This patch fixes
the issue by updating the PHY speed in the LP_PHY_CTL register (0x58)
according to the SControl speed.
Note that this fix is only applied if the compatible string
"marvell,armada-370-sata" is found in the SATA DT node.
Fixes: 9ae6f740b4 ("arm: mach-mvebu: add support for Armada 370 and Armada XP with DT")
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: stable@vger.kernel.org # v3.6+
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
The sata_mv driver supports the SATA IP found in several Marvell SoCs.
As some new SATA registers have been introduced with the Armada 370/XP
SoCs, a way to identify them is needed.
This patch introduces a new compatible string for the SATA IP found in
Armada 370/XP SoCs.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Lior Amsalem <alior@marvell.com>
Cc: stable@vger.kernel.org # v3.6+
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
If CONFIG_HAVE_CLK is not selected, then all the clk API turn out
into no-ops. In other words, there's no need to have the ifdefs.
The only side-effect of this patch is the extra tiny kmalloc,
but that's not enough reason to have such ugly ifdefs all around
the code.
tj: Slightly massaged comment as per Andrew Lunn.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
These forward declarations are no longer needed, and are probably
historical left-over.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dove can be configured without PCI. We then get a number of warnings:
warning: 'msi' defined but not used
warning: 'mv5_sht' defined but not used
warning: 'mv_dump_pci_cfg' defined but not used.
Move around variables and add #ifdef as necassary to fix the warnings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support for instantiating this driver from device tree, and add
the necassary DT information to the kirkwood.dtsi file.
This is based on previous work by Michael Walle and Jason Cooper.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Josh Coombs <josh.coombs@gmail.com>
The Orion kirkwood chips have a gatable clock per SATA channel. Add
code to get and enable this clk if it exists.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Gcc version 4.6.2-12 complains that if we can't find the "nr-ports"
property in of_property_read_u32_array() then "n_ports" is used
uninitialized. Let's set it to zero in that case.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use an getter function in plat-orion/addr-map.c to get the address map
structure, rather than pass it to drivers in the platform_data
structures. When the drivers are built for none orion platforms, a
dummy function is provided instead which returns NULL.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
The driver uses dev_get_drvdata() to get to the driver data for the
platform and PCI devices, while the corresponding wrappers exists for
them -- in one case it even declares an otherwise unneeded variable
to do that. Switch to using the {platform|pci}_get_drvdata() instead.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
mv_platfrom_probe() forgets to call clk_disable() and clk_put() iff
ata_host_activate() fails...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use a single mechanism to show driver version.
Reduces text a tiny bit too.
Remove uses of static int printed_version
Add and use ata_print_version(const struct device *, const char *ver)
and ata_print_version_once.
$ size drivers/ata/built-in.*
text data bss dec hex filename
544969 73893 116584 735446 b38d6 drivers/ata/built-in.allyesconfig.ata.o
543870 73893 116592 734355 b34ad drivers/ata/built-in.allyesconfig.print_once.o
141328 14689 4220 160237 271ed drivers/ata/built-in.defconfig.ata.o
141212 14689 4220 160121 27179 drivers/ata/built-in.defconfig.print_once.o
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Zheyu Ma
Lee Jones
Sergey Shtylyov
Gustavo A. R. Silva
Sascha Hauer
Jiri Slaby
Christoph Hellwig
Thomas Gleixner
Kees Cook
Jens Axboe
Jia-Ju Bai
Gustavo A. R. Silva
Colin Ian King
Andrew Lunn
Bhumika Goyal
Andy Shevchenko
Tejun Heo
Arvind Yadav
Uwe Kleine-König
Uwe Kleine-König
Harman Kalra
Ben Dooks
Quentin Lambert
Thomas Petazzoni
Markus Elfring
Wolfram Sang
Bartlomiej Zolnierkiewicz
Linus Torvalds
Ezequiel Garcia
Lior Amsalem
Simon Guinot
Jingoo Han
Greg Kroah-Hartman
Dan Carpenter
Sergei Shtylyov
Joe Perches