Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
net/ipv4/tcp_metrics.c
Overlapping changes between the "don't create two tcp metrics objects
with the same key" race fix in net and the addition of the destination
address in the lookup key in net-next.
Minor overlapping changes in bnx2x driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Batman-adv prepends a full ethernet header in addition to its own
header. This has to be reflected in the MTU calculation, especially
since the value is used to set dev->hard_header_len.
Introduced by 411d6ed93a
("batman-adv: consider network coding overhead when calculating required mtu")
Reported-by: cmsv <cmsv@wirelesspt.net>
Reported-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The following call chains indicate that batadv_is_on_batman_iface()
is always under rtnl_lock protection as call_netdevice_notifier()
is protected by rtnl_lock. So if __dev_get_by_index() rather than
dev_get_by_index() is used to find interface handler in it, this
would help us avoid to change interface reference counter.
call_netdevice_notifier()
batadv_hard_if_event()
batadv_hardif_add_interface()
batadv_is_valid_iface()
batadv_is_on_batman_iface()
Cc: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The crc16 functionality is not used anymore, therefore
we can safely remove the dependency in the Kbuild file.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
With unrolling the batadv_header into the respective structures, the
offsetof checks are now useless. Instead, add build checks for all
packet types which go over the wire to avoid problems with wrong sizes
or compatibility issues on some architectures which don't use every day.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Return at the end of void functions is not needed.
Since most of the void functions in the code do not do so,
make all the others consistent by removing the useless
returns. Actually all the functions to be "fixed" are in
network-coding.h only.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Show tables for the multi interface operation. Originator tables
are added per hard interface.
This patch also changes the API by adding the interface to the
bat_orig_print() parameters.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
To show information per interface, add a debugfs hardif structure
similar to the system in sysfs. Hard interface folders will be created
in "$debugfs/batman-adv/". Files are not yet added.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
With the new interface alternating, the first hop may send packets
in a round robin fashion to it's neighbors because it has multiple
valid routes built by the multi interface optimization. This patch
enables the feature if bonding is selected. Note that unlike the
bonding implemented before, this version is much simpler and may
even enable multi path routing to a certain degree.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The current OGM sending an aggregation functionality decides on
which interfaces a packet should be sent when it parses the forward
packet struct. However, with the network wide multi interface
optimization the outgoing interface is decided by the OGM processing
function.
This is reflected by moving the decision in the OGM processing function
and add the outgoing interface in the forwarding packet struct. This
practically implies that an OGM may be added multiple times (once per
outgoing interface), and this also affects aggregation which needs to
consider the outgoing interface as well.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
If the same interface is used for sending and receiving, there might be
throughput degradation on half-duplex interfaces such as WiFi. Add a
penalty if the same interface is used to reflect this problem in the
metric. At the same time, change the hop penalty from 30 to 15 so there
will be no change for single wifi mesh network. the effective hop
penalty will stay at 30 due to the new wifi penalty for these networks.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
For the network wide multi interface optimization there are different
routers for each outgoing interface (outgoing from the OGM perspective,
incoming for payload traffic). To reflect this, change the router and
associated data to a list of routers.
While at it, rename batadv_orig_node_get_router() to
batadv_orig_router_get() to follow the new naming scheme.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
For the network wide multi interface optimization it is required to save
metrics per outgoing interface in one neighbor. Therefore a new type is
introduced to keep interface-specific information. This also requires
some changes in access and list management.
The compare and equiv_or_better API calls are changed to take the
outgoing interface into consideration.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Remove bonding and interface alternating code - it will be replaced
by a new, network-wide multi interface optimization which enables
both bonding and interface alternating in a better way.
Keep the sysfs and find router function though, this will be needed
later.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
If a broadcast packet is coming from a client marked as
isolated, then mark the skb using the isolation mark so
that netfilter (or any other application) can recognise
them.
The mark is written in the skb based on the mask value:
only bits set in the mask are substitued by those in the
mark value
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The AP isolation status may be evaluated in different spots.
Create an helper function to avoid code duplication.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Change the AP isolation mechanism to not only "isolate" WIFI
clients but also all those marked with the more generic
"isolation flag" (BATADV_TT_CLIENT_ISOLA).
The result is that when AP isolation is on any unicast
packet originated by an "isolated" client and directed to
another "isolated" client is dropped at the source node.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Print the new BATADV_TT_CLIENT_ISOLA flag properly in the
Local and Global Translation Table output.
The character 'I' is used in the flags column to indicate
that the entry is marked as isolated.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
A client sending packets which mark matches the value
configured via sysfs has to be identified as isolated using
the TT_CLIENT_ISOLA flag.
The match is mask based, meaning that only bits set in the
mask are compared with those in the mark value.
If the configured mask is equal to 0 no operation is
performed.
Such flag is then advertised within the classic client
announcement mechanism.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
This attribute can be used to set and read the value and the
mask of the skb mark which will be used to classify the
source non-mesh client as ISOLATED. In this way a client can
be advertised as such and the mark can potentially be
restored at the receiving node before delivering the skb.
This can be helpful for creating network wide netfilter
policies.
This sysfs file expects a string of the shape "$mark/$mask".
Where $mark has to be a 32-bit number in any base, while
$mask must be a 32bit mask expressed in hex base. Only bits
in $mark covered by the bitmask are really stored.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
In different situations it is possible that the DHCP server
or client uses broadcast Ethernet frames to send messages
to each other. The GW component in batman-adv takes care of
using bat-unicast packets to bring broadcast DHCP
Discover/Requests to the "best" server.
On the way back the DHCP server usually sends unicasts,
but upon client request it may decide to use broadcasts as
well.
This patch improves the GW component so that it now snoops
and sends as unicast all the DHCP packets, no matter if they
were generated by a DHCP server or client.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Remove parenthesis around return expression as suggested by
checkpatch.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The function batadv_gw_deselect() is actually not deselecting
anything. It is just informing the GW code to perform a
re-election procedure when possible.
The current gateway is not being touched at all and therefore
the name of this function is rather misleading.
Rename it to batadv_gw_reselect() to batadv_gw_reselect()
to make its behaviour easier to grasp.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
When switching from gw_mode client to either off or server
the current selected gateway has to be deselected.
In this way when client mode is enabled again a gateway
re-election is forced and a GW_ADD event is consequently
sent.
The current behaviour instead is to keep the current gateway
leading to no GW_ADD event when gw_mode client is selected
for a second time
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
As suggested by checkpatch, remove all the references to the
FSF address since the kernel already has one reference in
its documentation.
In this way it is easier to update it in case of future
changes.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
If possible, operations like ntohs/ntohl should not be
performed too often. Use a variable to locally store the
converted value and then use it.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
When batadv_get_vid() is invoked in interface_rx() the
batman-adv header has already been removed, therefore
the header_len argument has to be 0.
Introduced by c018ad3de6
("batman-adv: add the VLAN ID attribute to the TT entry")
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
If an interface enslaved into batman-adv is a bridge (or a
virtual interface built on top of a bridge) the nf_bridge
member of the skbs reaching the soft-interface is filled
with the state about "netfilter bridge" operations.
Then, if one of such skbs is locally delivered, the nf_bridge
member should be cleaned up to avoid that the old state
could mess up with other "netfilter bridge" operations when
entering a second bridge.
This is needed because batman-adv is an encapsulation
protocol.
However at the moment skb->nf_bridge is not released at all
leading to bogus "netfilter bridge" behaviours.
Fix this by cleaning the netfilter state of the skb before
it gets delivered to the upper layer in interface_rx().
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Make struct batadv_tvlv_tt_change a multiple 4 bytes long
to avoid padding on any architecture.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Since this is a mac address and always 48 bit, and we can assume that
it is always aligned to 2-byte boundaries, add a pack(2) pragma.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
struct batadv_icmp_header currently has a size of 17, which
will be padded to 20 on some architectures. Fix this by
unrolling the header into the parent structures.
Moreover keep the ICMP parsing functions as generic as they
are now by using a stub icmp_header struct during packet
parsing.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The size of the batadv_header of 3 is problematic on some architectures
which automatically pad all structures to a 32 bit boundary. To not lose
performance by packing this struct, better embed it into the various
host structures.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The compiler may decide to pad the structure, and then it does not
have the expected size of 46 byte. Fix this by moving it in the
pragma pack(2) part of the code.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
It is better to use batadv_compate_eth instead of memcpy for
concise style.
Cc: Marek Lindner <mareklindner@neomailbox.ch>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Antonio Quartulli <antonio@meshcoding.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: b.a.t.m.a.n@lists.open-mesh.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the newly added generic routine ether_addr_equal_unaligned
to test if possibly unaligned to u16 Ethernet addresses are equal.
This slightly improves comparison time for systems with
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of handling icmp packets only up to length of icmp_packet_rr,
the code should handle any icmp length size. Therefore the length
truncating is moved to when the packet is actually sent to userspace
(this does not support lengths longer than icmp_packet_rr yet). Longer
packets are forwarded without truncating.
This patch also cleans up some parts where the icmp header struct could
be used instead of other icmp_packet(_rr) structs to make the code more
readable.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Flags covered by TT_SYNC_MASK are kept in sync among the
nodes in the network and therefore they have to be
considered while computing the global/local table CRC.
In this way a generic originator is able to understand if
its table contains the correct flags or not.
Bits from 4 to 7 in the TT flags fields are now reserved for
"synchronized" flags only.
This allows future developers to add more flags of this type
without breaking compatibility.
It's important to note that not all the remote TT flags are
synchronised. This comes from the fact that some flags are
used to inject an information once only.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Some flags (i.e. the WIFI flag) may change after that the
related client has already been announced. However it is
useful to informa the rest of the network about this change.
Add a runtime-flag-switch detection mechanism and
re-announce the related TT entry to advertise the new flag
value.
This mechanism can be easily exploited by future flags that
may need the same treatment.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Upcoming changes need to perform other checks on the
incoming net_device struct.
To avoid performing dev_get_by_index() for each and every
check, it is better to move it outside of is_wifi_iface()
and search the netdev object once only.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
In case of soft_iface destruction send a GW DEL event to
userspace so that applications which are listening for GW
events are informed about the lost of connectivity and can
react accordingly.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The local translation table size is limited by what can be
transferred from one node to another via a full table request.
The number of entries fitting into a full table request depend
on whether the fragmentation is enabled or not. Therefore this
patch introduces a max table size check and refuses to add
more local clients when that size is reached. Moreover, if the
max full table packet size changes (MTU change or fragmentation
is disabled) the local table is downsized instantaneously.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Antonio Quartulli <ordex@autistici.org>
David S. Miller
Simon Wunderlich
Marek Lindner
Ying Xue
Antonio Quartulli
Simon Wunderlich
Antonio Quartulli
dingtianhong
Joe Perches
Marek Lindner