entry.s only disables IRQs on hardware IRQ, move trace_hardirqs_off call
into do_interrupt. Check actual intlevel that will be restored on return
from exception handler to decide if trace_hardirqs_on should be called.
Annotate IRQ on/off points in the TIF_* handling loop on return from
exception handler.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Xtensa Performance Monitor Module has up to 8 32 bit wide performance
counters. Each counter may be enabled independently and can count any
single type of hardware performance events. Event counting may be enabled
and disabled globally (per PMM).
Each counter has status register with bits indicating if the counter has
been overflown and may be programmed to raise profiling IRQ on overflow.
This IRQ is used to rewind counters and allow for counting more than 2^32
samples for counting events and to report samples for sampling events.
For more details see Tensilica Debug User's Guide, chapter 8
"Performance monitor module".
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Old oprofile interface will share user stack tracing with new perf
interface. Move oprofile user/kernel stack tracing to stacktrace.c to
make it possible.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Restore original a0 in the kernel exception stack frame. This way it
looks like the frame that got interrupt/exception did alloca (copy a0 and
a1 spilled under old stack to the new location as well) to save registers
and then did a call to handler.
The point where interrupt/exception was taken is not in the stack chain,
only in pt_regs (call4 from that address can be simulated to keep it in
the stack trace).
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Existing users of ioremap_cache() are mapping memory that is known in
advance to not have i/o side effects. These users are forced to cast
away the __iomem annotation, or otherwise neglect to fix the sparse
errors thrown when dereferencing pointers to this memory. Provide
memremap() as a non __iomem annotated ioremap_*() in the case when
ioremap is otherwise a pointer to cacheable memory. Empirically,
ioremap_<cacheable-type>() call sites are seeking memory-like semantics
(e.g. speculative reads, and prefetching permitted).
memremap() is a break from the ioremap implementation pattern of adding
a new memremap_<type>() for each mapping type and having silent
compatibility fall backs. Instead, the implementation defines flags
that are passed to the central memremap() and if a mapping type is not
supported by an arch memremap returns NULL.
We introduce a memremap prototype as a trivial wrapper of
ioremap_cache() and ioremap_wt(). Later, once all ioremap_cache() and
ioremap_wt() usage has been removed from drivers we teach archs to
implement arch_memremap() with the ability to strictly enforce the
mapping type.
Cc: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Migrate xtensa driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: linux-xtensa@linux-xtensa.org
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Currently we have two different ways to signal an I/O error on a BIO:
(1) by clearing the BIO_UPTODATE flag
(2) by returning a Linux errno value to the bi_end_io callback
The first one has the drawback of only communicating a single possible
error (-EIO), and the second one has the drawback of not beeing persistent
when bios are queued up, and are not passed along from child to parent
bio in the ever more popular chaining scenario. Having both mechanisms
available has the additional drawback of utterly confusing driver authors
and introducing bugs where various I/O submitters only deal with one of
them, and the others have to add boilerplate code to deal with both kinds
of error returns.
So add a new bi_error field to store an errno value directly in struct
bio and remove the existing mechanisms to clean all this up.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This is a preparatory patch for moving irq_data struct members.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Chris Zankel <chris@zankel.net>
Link: http://lkml.kernel.org/r/20150713172018.264485572@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Move the now generic definitions of atomic_{set,clear}_mask() into
linux/atomic.h to avoid endless and pointless repetition.
Also, provide an atomic_andnot() wrapper for those few archs that can
implement that.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Implement atomic logic ops -- atomic_{or,xor,and}.
These will replace the atomic_{set,clear}_mask functions that are
available on some archs.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Implement atomic logic ops -- atomic_{or,xor,and}.
These will replace the atomic_{set,clear}_mask functions that are
available on some archs.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When we scan a PCI bus, we read PCI-PCI bridge window registers with
pci_read_bridge_bases() so we can validate the resource hierarchy. Most
architectures call pci_read_bridge_bases() from pcibios_fixup_bus(), but
PCI-PCI bridges are not arch-specific, so this doesn't need to be in
arch-specific code.
Call pci_read_bridge_bases() directly from the PCI core instead of from
arch code.
For alpha and mips, we now call pci_read_bridge_bases() always; previously
we only called it if PCI_PROBE_ONLY was set.
[bhelgaas: changelog]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: James E.J. Bottomley <jejb@parisc-linux.org>
CC: Michael Ellerman <mpe@ellerman.id.au>
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: David Howells <dhowells@redhat.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: Tony Luck <tony.luck@intel.com>
CC: David S. Miller <davem@davemloft.net>
CC: Ingo Molnar <mingo@redhat.com>
CC: Guenter Roeck <linux@roeck-us.net>
CC: Michal Simek <monstr@monstr.eu>
CC: Chris Zankel <chris@zankel.net>
No one uses this anymore, and this is not the first time the
idea of replacing it with a (now possible) userspace side.
Lock stealing logic was removed long ago in when the lock
was granted to the highest prio.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1435782588-4177-2-git-send-email-dave@stgolabs.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit 2ae416b142 ("mm: new mm hook framework") introduced an empty
header file (mm-arch-hooks.h) for every architecture, even those which
doesn't need to define mm hooks.
As suggested by Geert Uytterhoeven, this could be cleaned through the use
of a generic header file included via each per architecture
asm/include/Kbuild file.
The PowerPC architecture is not impacted here since this architecture has
to defined the arch_remap MM hook.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Userspace return code may skip restoring THREADPTR register if there are
no registers that need to be zeroed. This leads to spurious failures in
libc NPTL tests.
Always restore THREADPTR on return to userspace.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Added the x86 implementation of word-at-a-time to the
generic version, which previously only supported big-endian.
Omitted the x86-specific load_unaligned_zeropad(), which in
any case is also not present for the existing BE-only
implementation of a word-at-a-time, and is only used under
CONFIG_DCACHE_WORD_ACCESS.
Added as a "generic-y" to the Kbuilds of all architectures
that didn't previously have it.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVkO5XAAoJEOvOhAQsB9HWe4cQAJcsmSXIDN2O6oxvgH8Wilof
EIEMvT13uwBdsjQdYUY6A6B3iUV9wzEEgoosg/JRgpz5/b1FTDMIO4arUPD3Lcak
5bmyVO2qAT+yaLAWSgn6I8DMplXrKiEuK+TkH/mW3p9TdvElLdG3Vg6UI407hSWv
W0QbVwkNtv8XmzshV9F2YdmflT8j1PgYxIu/tEkVOWn37DNW+Fp2OVBrdTIYp3AJ
X6bYZPEcQDCrWWW/s2GmIDrNgryiebasns+CAgGY21262jAYaRcFOJmR47AsTqW7
DSZXIlLc/gJca++hfxqV15RZ4NRHxrebCypTsPtZUV7ZiYHI726eeUZzxsp/9itu
mvhmi+aQUTTUP3dDhiv05f4syAKEb4zslT6SLwcna6oi09M97HfCeQsHqhcFq/MG
KnS2JJoJQToQtJvMUXMQzp5hyHjNlOclIvCxEiL32EZU54PeJOKasy/mptNGEctk
TxACWvoXBQglRaVN+1wIjjr0BaHJSuJa9CUnIfM4WZdSHiMQMx00XLTkZcTnSM6R
12pE54vVolrXswGPJhy4W/Sf1yPSW1tkWSVBbkKLyCIrlAWJtu68rXhvwhG/nz6E
3g6QrDEQGlk6bzUH4CJCEqXLPRN1bNS0XjdkEFh60Lury3Ns5yHKZXPW5vCQ5csr
FQNUyBs595CWbJNfbn1n
=0BDx
-----END PGP SIGNATURE-----
Merge tag 'module_init-device_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull module_init replacement part one from Paul Gortmaker:
"Replace module_init with equivalent device_initcall in non modules.
This series of commits converts non-modular code that is using the
module_init() call to hook itself into the system to instead use
device_initcall().
The conversion is a runtime no-op, since module_init actually becomes
__initcall in the non-modular case, and that in turn gets mapped onto
device_initcall. A couple files show a larger negative diffstat,
representing ones that had a module_exit function that we remove here
vs previously relying on the linker to dispose of it.
We make this conversion now, so that we can relocate module_init from
init.h into module.h in the future.
The files changed here are just limited to those that would otherwise
have to add module.h to obviously non-modular code, in order to avoid
a compile fail, as testing has shown"
* tag 'module_init-device_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
MIPS: don't use module_init in non-modular cobalt/mtd.c file
drivers/leds: don't use module_init in non-modular leds-cobalt-raq.c
cris: don't use module_init for non-modular core eeprom.c code
tty/metag_da: Avoid module_init/module_exit in non-modular code
drivers/clk: don't use module_init in clk-nomadik.c which is non-modular
xtensa: don't use module_init for non-modular core network.c code
sh: don't use module_init in non-modular psw.c code
mn10300: don't use module_init in non-modular flash.c code
parisc64: don't use module_init for non-modular core perf code
parisc: don't use module_init for non-modular core pdc_cons code
cris: don't use module_init for non-modular core intmem.c code
ia64: don't use module_init in non-modular sim/simscsi.c code
ia64: don't use module_init for non-modular core kernel/mca.c code
arm: don't use module_init in non-modular mach-vexpress/spc.c code
powerpc: don't use module_init in non-modular 83xx suspend code
powerpc: use device_initcall for registering rtc devices
x86: don't use module_init in non-modular devicetree.c code
x86: don't use module_init in non-modular intel_mid_vrtc.c
Pull asm/scatterlist.h removal from Jens Axboe:
"We don't have any specific arch scatterlist anymore, since parisc
finally switched over. Kill the include"
* 'for-4.2/sg' of git://git.kernel.dk/linux-block:
remove scatterlist.h generation from arch Kbuild files
remove <asm/scatterlist.h>
CRIU is recreating the process memory layout by remapping the checkpointee
memory area on top of the current process (criu). This includes remapping
the vDSO to the place it has at checkpoint time.
However some architectures like powerpc are keeping a reference to the
vDSO base address to build the signal return stack frame by calling the
vDSO sigreturn service. So once the vDSO has been moved, this reference
is no more valid and the signal frame built later are not usable.
This patch serie is introducing a new mm hook framework, and a new
arch_remap hook which is called when mremap is done and the mm lock still
hold. The next patch is adding the vDSO remap and unmap tracking to the
powerpc architecture.
This patch (of 3):
This patch introduces a new set of header file to manage mm hooks:
- per architecture empty header file (arch/x/include/asm/mm-arch-hooks.h)
- a generic header (include/linux/mm-arch-hooks.h)
The architecture which need to overwrite a hook as to redefine it in its
header file, while architecture which doesn't need have nothing to do.
The default hooks are defined in the generic header and are used in the
case the architecture is not defining it.
In a next step, mm hooks defined in include/asm-generic/mm_hooks.h should
be moved here.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This replaces the plain loop over the sglist array with for_each_sg()
macro which consists of sg_next() function calls. Since xtensa doesn't
select ARCH_HAS_SG_CHAIN, it is not necessary to use for_each_sg() in
order to loop over each sg element. But this can help find problems
with drivers that do not properly initialize their sg tables when
CONFIG_DEBUG_SG is enabled.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86 core updates from Ingo Molnar:
"There were so many changes in the x86/asm, x86/apic and x86/mm topics
in this cycle that the topical separation of -tip broke down somewhat -
so the result is a more traditional architecture pull request,
collected into the 'x86/core' topic.
The topics were still maintained separately as far as possible, so
bisectability and conceptual separation should still be pretty good -
but there were a handful of merge points to avoid excessive
dependencies (and conflicts) that would have been poorly tested in the
end.
The next cycle will hopefully be much more quiet (or at least will
have fewer dependencies).
The main changes in this cycle were:
* x86/apic changes, with related IRQ core changes: (Jiang Liu, Thomas
Gleixner)
- This is the second and most intrusive part of changes to the x86
interrupt handling - full conversion to hierarchical interrupt
domains:
[IOAPIC domain] -----
|
[MSI domain] --------[Remapping domain] ----- [ Vector domain ]
| (optional) |
[HPET MSI domain] ----- |
|
[DMAR domain] -----------------------------
|
[Legacy domain] -----------------------------
This now reflects the actual hardware and allowed us to distangle
the domain specific code from the underlying parent domain, which
can be optional in the case of interrupt remapping. It's a clear
separation of functionality and removes quite some duct tape
constructs which plugged the remap code between ioapic/msi/hpet
and the vector management.
- Intel IOMMU IRQ remapping enhancements, to allow direct interrupt
injection into guests (Feng Wu)
* x86/asm changes:
- Tons of cleanups and small speedups, micro-optimizations. This
is in preparation to move a good chunk of the low level entry
code from assembly to C code (Denys Vlasenko, Andy Lutomirski,
Brian Gerst)
- Moved all system entry related code to a new home under
arch/x86/entry/ (Ingo Molnar)
- Removal of the fragile and ugly CFI dwarf debuginfo annotations.
Conversion to C will reintroduce many of them - but meanwhile
they are only getting in the way, and the upstream kernel does
not rely on them (Ingo Molnar)
- NOP handling refinements. (Borislav Petkov)
* x86/mm changes:
- Big PAT and MTRR rework: making the code more robust and
preparing to phase out exposing direct MTRR interfaces to drivers -
in favor of using PAT driven interfaces (Toshi Kani, Luis R
Rodriguez, Borislav Petkov)
- New ioremap_wt()/set_memory_wt() interfaces to support
Write-Through cached memory mappings. This is especially
important for good performance on NVDIMM hardware (Toshi Kani)
* x86/ras changes:
- Add support for deferred errors on AMD (Aravind Gopalakrishnan)
This is an important RAS feature which adds hardware support for
poisoned data. That means roughly that the hardware marks data
which it has detected as corrupted but wasn't able to correct, as
poisoned data and raises an APIC interrupt to signal that in the
form of a deferred error. It is the OS's responsibility then to
take proper recovery action and thus prolonge system lifetime as
far as possible.
- Add support for Intel "Local MCE"s: upcoming CPUs will support
CPU-local MCE interrupts, as opposed to the traditional system-
wide broadcasted MCE interrupts (Ashok Raj)
- Misc cleanups (Borislav Petkov)
* x86/platform changes:
- Intel Atom SoC updates
... and lots of other cleanups, fixlets and other changes - see the
shortlog and the Git log for details"
* 'x86-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (222 commits)
x86/hpet: Use proper hpet device number for MSI allocation
x86/hpet: Check for irq==0 when allocating hpet MSI interrupts
x86/mm/pat, drivers/infiniband/ipath: Use arch_phys_wc_add() and require PAT disabled
x86/mm/pat, drivers/media/ivtv: Use arch_phys_wc_add() and require PAT disabled
x86/platform/intel/baytrail: Add comments about why we disabled HPET on Baytrail
genirq: Prevent crash in irq_move_irq()
genirq: Enhance irq_data_to_desc() to support hierarchy irqdomain
iommu, x86: Properly handle posted interrupts for IOMMU hotplug
iommu, x86: Provide irq_remapping_cap() interface
iommu, x86: Setup Posted-Interrupts capability for Intel iommu
iommu, x86: Add cap_pi_support() to detect VT-d PI capability
iommu, x86: Avoid migrating VT-d posted interrupts
iommu, x86: Save the mode (posted or remapped) of an IRTE
iommu, x86: Implement irq_set_vcpu_affinity for intel_ir_chip
iommu: dmar: Provide helper to copy shared irte fields
iommu: dmar: Extend struct irte for VT-d Posted-Interrupts
iommu: Add new member capability to struct irq_remap_ops
x86/asm/entry/64: Disentangle error_entry/exit gsbase/ebx/usermode code
x86/asm/entry/32: Shorten __audit_syscall_entry() args preparation
x86/asm/entry/32: Explain reloading of registers after __audit_syscall_entry()
...
The network.c code is piggybacking off of the arch independent
CONFIG_NET, which is bool. So the code is either built in or
absent. It will never be modular, so using module_init as an
alias for __initcall is rather misleading.
Fix this up now, so that we can relocate module_init from
init.h into module.h in the future. If we don't do this, we'd
have to add module.h to obviously non-modular code, and that
would be a worse thing.
Direct use of __initcall is discouraged, vs prioritized ones.
Use of device_initcall is consistent with what __initcall
maps onto, and hence does not change the init order, making the
impact of this change zero. Should someone with real hardware
for boot testing want to change it later to arch_initcall or
something different, they can do that at a later date.
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Thomas Meyer <thomas@m3y3r.de>
Cc: linux-xtensa@linux-xtensa.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Add ioremap_wt() to all arch-specific asm/io.h headers which
define ioremap_wc() locally. These headers do not include
<asm-generic/iomap.h>. Some of them include <asm-generic/io.h>,
but ioremap_wt() is defined for consistency since they define
all ioremap_xxx locally.
In all architectures without Write-Through support, ioremap_wt()
is defined indentical to ioremap_nocache().
frv and m68k already have ioremap_writethrough(). On those we
add ioremap_wt() indetical to ioremap_writethrough() and defines
ARCH_HAS_IOREMAP_WT in both architectures.
The ioremap_wt() interface is exported to drivers.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Elliott@hp.com
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: arnd@arndb.de
Cc: hch@lst.de
Cc: hmh@hmh.eng.br
Cc: jgross@suse.com
Cc: konrad.wilk@oracle.com
Cc: linux-mm <linux-mm@kvack.org>
Cc: linux-nvdimm@lists.01.org
Cc: stefan.bader@canonical.com
Cc: yigal@plexistor.com
Link: http://lkml.kernel.org/r/1433436928-31903-9-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
xtensa:allmodconfig fails to build with the following errors.
drivers/gpu/drm/nouveau/nvkm/subdev/instmem/gk20a.c:
In function ‘gk20a_instobj_dtor_dma’:
drivers/gpu/drm/nouveau/nvkm/subdev/instmem/gk20a.c:154:2: error:
implicit declaration of function ‘dma_free_attrs’
drivers/gpu/drm/nouveau/nvkm/subdev/instmem/gk20a.c:
In function ‘gk20a_instobj_ctor_dma’:
drivers/gpu/drm/nouveau/nvkm/subdev/instmem/gk20a.c:218:2: error:
implicit declaration of function ‘dma_alloc_attrs’
Xtensa does not provide those functions at this time.
Provide dummy implementations to avoid build errors.
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Chris Zankel <chris@zankel.net>
Introduce faulthandler_disabled() and use it to check for irq context and
disabled pagefaults (via pagefault_disable()) in the pagefault handlers.
Please note that we keep the in_atomic() checks in place - to detect
whether in irq context (in which case preemption is always properly
disabled).
In contrast, preempt_disable() should never be used to disable pagefaults.
With !CONFIG_PREEMPT_COUNT, preempt_disable() doesn't modify the preempt
counter, and therefore the result of in_atomic() differs.
We validate that condition by using might_fault() checks when calling
might_sleep().
Therefore, add a comment to faulthandler_disabled(), describing why this
is needed.
faulthandler_disabled() and pagefault_disable() are defined in
linux/uaccess.h, so let's properly add that include to all relevant files.
This patch is based on a patch from Thomas Gleixner.
Reviewed-and-tested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: David.Laight@ACULAB.COM
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: airlied@linux.ie
Cc: akpm@linux-foundation.org
Cc: benh@kernel.crashing.org
Cc: bigeasy@linutronix.de
Cc: borntraeger@de.ibm.com
Cc: daniel.vetter@intel.com
Cc: heiko.carstens@de.ibm.com
Cc: herbert@gondor.apana.org.au
Cc: hocko@suse.cz
Cc: hughd@google.com
Cc: mst@redhat.com
Cc: paulus@samba.org
Cc: ralf@linux-mips.org
Cc: schwidefsky@de.ibm.com
Cc: yang.shi@windriver.com
Link: http://lkml.kernel.org/r/1431359540-32227-7-git-send-email-dahi@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We don't have any arch specific scatterlist now that parisc switched over
to the generic one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
- fix linker script transformation for .text / .text.fixup
- wire bpf and execveat syscalls;
- provide __NR_sync_file_range2 instead of __NR_sync_file_range, as that's
what xtensa uses.
- make xtfpgs LCD driver functional and configurable. This fixes hardware
lockup on KC705/ML605 boot;
- add audio subsystem bits to xtfpga DTS and provide sample KC705 config
with audio features enabled.
- add CY7C67300 USB controller support to XTFPGA.
- fix locking issues in ISS network driver;
- document PIC and MX interrupt distributor device tree bindings;
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wl+K
-----END PGP SIGNATURE-----
Merge tag 'xtensa-20150416' of git://github.com/czankel/xtensa-linux
Pull Xtensa updates from Chris Zankel:
- fix linker script transformation for .text / .text.fixup
- wire bpf and execveat syscalls
- provide __NR_sync_file_range2 instead of __NR_sync_file_range, as
that's what xtensa uses.
- make xtfpgs LCD driver functional and configurable. This fixes
hardware lockup on KC705/ML605 boot
- add audio subsystem bits to xtfpga DTS and provide sample KC705
config with audio features enabled
- add CY7C67300 USB controller support to XTFPGA
- fix locking issues in ISS network driver
- document PIC and MX interrupt distributor device tree bindings
* tag 'xtensa-20150416' of git://github.com/czankel/xtensa-linux:
xtensa: xtfpga: add CY7C67300 USB controller support
irqchip: xtensa-pic: xtensa-mx: document DT bindings
xtensa: ISS: fix locking in TAP network adapter
xtensa: Fix fix linker script transformation for .text / .text.fixup
xtensa: provide __NR_sync_file_range2 instead of __NR_sync_file_range
xtensa: wire bpf and execveat syscalls
xtensa: xtfpga: fix hardware lockup caused by LCD driver
xtensa: xtfpga: provide defconfig with audio subsystem
xtensa: xtfpga: add audio card to xtfpga DTS
Pull exec domain removal from Richard Weinberger:
"This series removes execution domain support from Linux.
The idea behind exec domains was to support different ABIs. The
feature was never complete nor stable. Let's rip it out and make the
kernel signal handling code less complicated"
* 'exec_domain_rip_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/misc: (27 commits)
arm64: Removed unused variable
sparc: Fix execution domain removal
Remove rest of exec domains.
arch: Remove exec_domain from remaining archs
arc: Remove signal translation and exec_domain
xtensa: Remove signal translation and exec_domain
xtensa: Autogenerate offsets in struct thread_info
x86: Remove signal translation and exec_domain
unicore32: Remove signal translation and exec_domain
um: Remove signal translation and exec_domain
tile: Remove signal translation and exec_domain
sparc: Remove signal translation and exec_domain
sh: Remove signal translation and exec_domain
s390: Remove signal translation and exec_domain
mn10300: Remove signal translation and exec_domain
microblaze: Remove signal translation and exec_domain
m68k: Remove signal translation and exec_domain
m32r: Remove signal translation and exec_domain
m32r: Autogenerate offsets in struct thread_info
frv: Remove signal translation and exec_domain
...
Pull vfs update from Al Viro:
"Part one:
- struct filename-related cleanups
- saner iov_iter_init() replacements (and switching the syscalls to
use of those)
- ntfs switch to ->write_iter() (Anton)
- aio cleanups and splitting iocb into common and async parts
(Christoph)
- assorted fixes (me, bfields, Andrew Elble)
There's a lot more, including the completion of switchover to
->{read,write}_iter(), d_inode/d_backing_inode annotations, f_flags
race fixes, etc, but that goes after #for-davem merge. David has
pulled it, and once it's in I'll send the next vfs pull request"
* 'for-linus-1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (35 commits)
sg_start_req(): use import_iovec()
sg_start_req(): make sure that there's not too many elements in iovec
blk_rq_map_user(): use import_single_range()
sg_io(): use import_iovec()
process_vm_access: switch to {compat_,}import_iovec()
switch keyctl_instantiate_key_common() to iov_iter
switch {compat_,}do_readv_writev() to {compat_,}import_iovec()
aio_setup_vectored_rw(): switch to {compat_,}import_iovec()
vmsplice_to_user(): switch to import_iovec()
kill aio_setup_single_vector()
aio: simplify arguments of aio_setup_..._rw()
aio: lift iov_iter_init() into aio_setup_..._rw()
lift iov_iter into {compat_,}do_readv_writev()
NFS: fix BUG() crash in notify_change() with patch to chown_common()
dcache: return -ESTALE not -EBUSY on distributed fs race
NTFS: Version 2.1.32 - Update file write from aio_write to write_iter.
VFS: Add iov_iter_fault_in_multipages_readable()
drop bogus check in file_open_root()
switch security_inode_getattr() to struct path *
constify tomoyo_realpath_from_path()
...
- fix locking issues in ISS network driver;
- document PIC and MX interrupt distributor device tree bindings;
- add CY7C67300 USB controller support to XTFPGA.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sZxq
-----END PGP SIGNATURE-----
Merge tag 'xtensa-for-next-20150413' of git://github.com/jcmvbkbc/linux-xtensa into for_next
Xtensa improvements for 4.1:
- fix locking issues in ISS network driver;
- document PIC and MX interrupt distributor device tree bindings;
- add CY7C67300 USB controller support to XTFPGA.
Signed-off-by: Chris Zankel <chris@zankel.net>
- don't lock lp->lock in the iss_net_timer for the call of iss_net_poll,
it will lock it itself;
- invert order of lp->lock and opened_lock acquisition in the
iss_net_open to make it consistent with iss_net_poll;
- replace spin_lock with spin_lock_bh when acquiring locks used in
iss_net_timer from non-atomic context;
- replace spin_lock_irqsave with spin_lock_bh in the iss_net_start_xmit
as the driver doesn't use lp->lock in the hard IRQ context;
- replace __SPIN_LOCK_UNLOCKED(lp.lock) with spin_lock_init, otherwise
lockdep is unhappy about using non-static key.
Cc: <stable@vger.kernel.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
As execution domain support is gone we can remove
signal translation from the signal code and remove
exec_domain from thread_info.
Signed-off-by: Richard Weinberger <richard@nod.at>
Commit 779c88c94c ("ARM: 8321/1: asm-generic: introduce .text.fixup
input section") introduced a new .text.fixup section which is merged
with .text at link time. This causes xtensa builds to fail with lots
of error messages similar to the following.
lib/lib.a(kobject.o): In function `kobject_create':
(.text+0x498): dangerous relocation: l32r: literal placed after use:
(.literal+0x150)
Linker script transformation needs to be updated to detect and handle
the new section.
Fixes: 779c88c94c ("ARM: 8321/1: asm-generic: introduce .text.fixup
input section")
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Chris Zankel <chris@zankel.net>
Previously, pci_scan_root_bus() created a root PCI bus, enumerated the
devices on it, and called pci_bus_add_devices(), which made the devices
available for drivers to claim them.
Most callers assigned resources to devices after pci_scan_root_bus()
returns, which may be after drivers have claimed the devices. This is
incorrect; the PCI core should not change device resources while a driver
is managing the device.
Remove pci_bus_add_devices() from pci_scan_root_bus() and do it after any
resource assignment in the callers.
Note that ARM's pci_common_init_dev() already called pci_bus_add_devices()
after pci_scan_root_bus(), so we only need to remove the first call:
pci_common_init_dev
pcibios_init_hw
pci_scan_root_bus
pci_bus_add_devices # first call
pci_bus_assign_resources
pci_bus_add_devices # second call
[bhelgaas: changelog, drop "root_bus" var in alpha common_init_pci(),
return failure earlier in mn10300, add "return" in x86 pcibios_scan_root(),
return early if xtensa platform_pcibios_fixup() fails]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
CC: Matt Turner <mattst88@gmail.com>
CC: David Howells <dhowells@redhat.com>
CC: Tony Luck <tony.luck@intel.com>
CC: Michal Simek <monstr@monstr.eu>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
CC: Sebastian Ott <sebott@linux.vnet.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Chris Metcalf <cmetcalf@ezchip.com>
CC: Chris Zankel <chris@zankel.net>
CC: Max Filippov <jcmvbkbc@gmail.com>
CC: Thomas Gleixner <tglx@linutronix.de>
- make xtfpgs LCD driver functional and configurable. This fixes hardware
lockup on KC705/ML605 boot;
- wire bpf and execveat syscalls;
- provide __NR_sync_file_range2 instead of __NR_sync_file_range, as that's
what xtensa uses.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=y80U
-----END PGP SIGNATURE-----
Merge tag 'xtensa-for-next-20150304' of git://github.com/jcmvbkbc/linux-xtensa into for_next
Xtensa fixes for 4.0:
- make xtfpgs LCD driver functional and configurable. This fixes hardware
lockup on KC705/ML605 boot;
- wire bpf and execveat syscalls;
- provide __NR_sync_file_range2 instead of __NR_sync_file_range, as that's
what xtensa uses.
xtensa actually uses sync_file_range2 implementation, so it should
define __NR_sync_file_range2 as other architectures that use that
function. That fixes userspace interface (that apparently never worked)
and avoids special-casing xtensa in libc implementations.
See the thread ending at
http://lists.busybox.net/pipermail/uclibc/2015-February/048833.html
for more details.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
LCD driver is always built for the XTFPGA platform, but its base address
is not configurable, and is wrong for ML605/KC705. Its initialization
locks up KC705 board hardware.
Make the whole driver optional, and its base address and bus width
configurable. Implement 4-bit bus access method.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Like in 3.19, I once more have a multi-stage cleanup for one asm-generic
header file, this time the work was done by Michael Tsirkin and cleans
up the uaccess.h file in asm-generic, as well as all architectures for
which the respective maintainers did not pick up his patches directly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=LROx
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic uaccess.h cleanup from Arnd Bergmann:
"Like in 3.19, I once more have a multi-stage cleanup for one
asm-generic header file, this time the work was done by Michael
Tsirkin and cleans up the uaccess.h file in asm-generic, as well as
all architectures for which the respective maintainers did not pick up
his patches directly"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (37 commits)
sparc32: nocheck uaccess coding style tweaks
sparc64: nocheck uaccess coding style tweaks
xtensa: macro whitespace fixes
sh: macro whitespace fixes
parisc: macro whitespace fixes
m68k: macro whitespace fixes
m32r: macro whitespace fixes
frv: macro whitespace fixes
cris: macro whitespace fixes
avr32: macro whitespace fixes
arm64: macro whitespace fixes
arm: macro whitespace fixes
alpha: macro whitespace fixes
blackfin: macro whitespace fixes
sparc64: uaccess_64 macro whitespace fixes
sparc32: uaccess_32 macro whitespace fixes
avr32: whitespace fix
sh: fix put_user sparse errors
metag: fix put_user sparse errors
ia64: fix put_user sparse errors
...
printk and friends can now format bitmaps using '%*pb[l]'. cpumask
and nodemask also provide cpumask_pr_args() and nodemask_pr_args()
respectively which can be used to generate the two printf arguments
necessary to format the specified cpu/nodemask.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If an attacker can cause a controlled kernel stack overflow, overwriting
the restart block is a very juicy exploit target. This is because the
restart_block is held in the same memory allocation as the kernel stack.
Moving the restart block to struct task_struct prevents this exploit by
making the restart_block harder to locate.
Note that there are other fields in thread_info that are also easy
targets, at least on some architectures.
It's also a decent simplification, since the restart code is more or less
identical on all architectures.
[james.hogan@imgtec.com: metag: align thread_info::supervisor_stack]
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: David Miller <davem@davemloft.net>
Acked-by: Richard Weinberger <richard@nod.at>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Tested-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
LKP has triggered a compiler warning after my recent patch "mm: account
pmd page tables to the process":
mm/mmap.c: In function 'exit_mmap':
>> mm/mmap.c:2857:2: warning: right shift count >= width of type [enabled by default]
The code:
> 2857 WARN_ON(mm_nr_pmds(mm) >
2858 round_up(FIRST_USER_ADDRESS, PUD_SIZE) >> PUD_SHIFT);
In this, on tile, we have FIRST_USER_ADDRESS defined as 0. round_up() has
the same type -- int. PUD_SHIFT.
I think the best way to fix it is to define FIRST_USER_ADDRESS as unsigned
long. On every arch for consistency.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the generic KC705 defconfig with all pieces of xtfpga audio
subsystem enabled: I2C, SPI and ASoC support, I2C master, SPI master,
clock synthesizer, I2S master, audio codec and audio card drivers.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
This includes OpenCores I2C host controller, TI CDCE706 clock generator,
xtfpga I2S master controller, xtfpga SPI master controller, TI TLV320AIC23
audio codec and a simple audio card.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
The core VM already knows about VM_FAULT_SIGBUS, but cannot return a
"you should SIGSEGV" error, because the SIGSEGV case was generally
handled by the caller - usually the architecture fault handler.
That results in lots of duplication - all the architecture fault
handlers end up doing very similar "look up vma, check permissions, do
retries etc" - but it generally works. However, there are cases where
the VM actually wants to SIGSEGV, and applications _expect_ SIGSEGV.
In particular, when accessing the stack guard page, libsigsegv expects a
SIGSEGV. And it usually got one, because the stack growth is handled by
that duplicated architecture fault handler.
However, when the generic VM layer started propagating the error return
from the stack expansion in commit fee7e49d45 ("mm: propagate error
from stack expansion even for guard page"), that now exposed the
existing VM_FAULT_SIGBUS result to user space. And user space really
expected SIGSEGV, not SIGBUS.
To fix that case, we need to add a VM_FAULT_SIGSEGV, and teach all those
duplicate architecture fault handlers about it. They all already have
the code to handle SIGSEGV, so it's about just tying that new return
value to the existing code, but it's all a bit annoying.
This is the mindless minimal patch to do this. A more extensive patch
would be to try to gather up the mostly shared fault handling logic into
one generic helper routine, and long-term we really should do that
cleanup.
Just from this patch, you can generally see that most architectures just
copied (directly or indirectly) the old x86 way of doing things, but in
the meantime that original x86 model has been improved to hold the VM
semaphore for shorter times etc and to handle VM_FAULT_RETRY and other
"newer" things, so it would be a good idea to bring all those
improvements to the generic case and teach other architectures about
them too.
Reported-and-tested-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Jan Engelhardt <jengelh@inai.de>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> # "s390 still compiles and boots"
Cc: linux-arch@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While working on arch/xtensa/include/asm/uaccess.h, I noticed
that some macros within this header are made harder to read because they
violate a coding style rule: space is missing after comma.
Fix it up.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
- fix nommu support;
- remove s6000 variant and s6105 platform.
- fix permissions for kmapped pages so that copy_to_user_page works with them.
- add power management menu to Kconfig to allow use of runtime PM.
- disable linker optimizations because of a linker bug.
- fix sparse error.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ePa2
-----END PGP SIGNATURE-----
Merge tag 'xtensa-next-20141215' of git://github.com/czankel/xtensa-linux
Pull Xtensa fixes from Chris Zankel:
- fix nommu support
- remove s6000 variant and s6105 platform
- fix permissions for kmapped pages so that copy_to_user_page works with them
- add power management menu to Kconfig to allow use of runtime PM
- disable linker optimizations because of a linker bug
- fix sparse error
* tag 'xtensa-next-20141215' of git://github.com/czankel/xtensa-linux:
xtensa: disable link optimization
xtensa/uaccess: fix sparse errors
xtensa: fix kmap_prot definition
xtensa: add power management menu to Kconfig
xtensa: remove s6000 variant and s6105 platform
xtensa: make PLATFORM_DEFAULT_MEM parameters configurable
xtensa: nommu: clean up memory map dump
xtensa: nommu: reserve memory below PLATFORM_DEFAULT_MEM_START
xtensa: nommu: set up cache and atomctl in initialize_mmu
xtensa: move vecbase SR initialization to _startup
xtensa: nommu: fix uImage load address
xtensa: nommu: fix load address definitions
xtensa: nommu: fix Image.elf reset code and ld script
xtensa: nommu: add MMU dependency to DEBUG_TLB_SANITY
xtensa: nommu: don't build most of the cache flushing code
xtensa: nommu: don't provide arch_get_unmapped_area
xtensa: nommu: provide MAP_UNINITIALIZED definition
xtensa: nommu: provide _PAGE_CHG_MASK definition
xtensa: nommu: provide __invalidate_dcache_page_alias stub
xtensa: nommu: move init_mmu stub to nommu_context.h
The default linker behavior is to optimize identical literal values
and remove unnecessary overhead. However, because of a bug in the
linker, this currently results in an error ('call target out of range').
Disable link-time optimizations per default until there is a fix
for the linker and add the option to iss_defconfig.
Signed-off-by: Chris Zankel <chris@zankel.net>
virtio wants to read bitwise types from userspace using get_user. At the
moment this triggers sparse errors, since the value is passed through an
integer.
Fix that up using __force.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
- fix permissions for kmapped pages so that copy_to_user_page works with
them;
- add power management menu to Kconfig to allow use of runtime PM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUi7VsAAoJEFH5zJH4P6BEpS8P/jsHzgGyaCmvr8MI+I6wImIt
orEhkxOYQS4aBAi/azupTPYbu8r2I8+yscWtFxBnvJok3rT2yMtSJZFLUhur0nG4
DQwQduMeHbzSC4ADqJBalfaOfpcwz/GQoM6IPVZEEW6h4vzCvUm0O1Wq5Z1Thbg2
skMmVFIX2+YTwUrEKMEqbl1JevNzNH53t/tlTgiXOMkZWwL1R4ToRsFHv9zpIJ1m
Srm0BWAXAM+h1vx1Pv2vwmTcgPj3MdBccsla/HAybeQraqThdlgAz9Cnk5T5AdWE
6rLy9mw+LiT1kXnbl4Z526NBzvkf+5+xYiGqI3UwohhFEChq74PBPQnZlpZ2AGlG
dI/i9CoV0uQgU3rRDvS9NNFXXW59objKIu8f2Od5pS4kgV+mPjKePVTJbchXIf5n
MC7Dq2GcM8jK4/Q32aHNxDi9jM3jukd7pJHbyxOo0g1SpmSEnNSJ+CcOV5ft6nLB
xIohvVXg8Om976Xbl6eRii7lNdCZm8j7mDNMl37lwaqitIgZmlGeRhAyYCnjC1Pl
mxtORfQbGfUHw/o8TlhyINBNQdpLr0CRTL4HCrMyiDDQ0mJH3bMBKuSk7y0Qe8DG
aJ8Om29CKvawr3irehNRsZiSfoqiPG6F/GzfFxfgSut/AKAMI25kMSoGZCjBMhHn
76+jWe4WzygZCAUWzmsl
=9vUt
-----END PGP SIGNATURE-----
Merge tag 'xtensa-for-next-20141213' of git://github.com/jcmvbkbc/linux-xtensa into for_next
Xtensa improvements for 3.19:
- fix permissions for kmapped pages so that copy_to_user_page works with
them;
- add power management menu to Kconfig to allow use of runtime PM.
Pull networking updates from David Miller:
1) New offloading infrastructure and example 'rocker' driver for
offloading of switching and routing to hardware.
This work was done by a large group of dedicated individuals, not
limited to: Scott Feldman, Jiri Pirko, Thomas Graf, John Fastabend,
Jamal Hadi Salim, Andy Gospodarek, Florian Fainelli, Roopa Prabhu
2) Start making the networking operate on IOV iterators instead of
modifying iov objects in-situ during transfers. Thanks to Al Viro
and Herbert Xu.
3) A set of new netlink interfaces for the TIPC stack, from Richard
Alpe.
4) Remove unnecessary looping during ipv6 routing lookups, from Martin
KaFai Lau.
5) Add PAUSE frame generation support to gianfar driver, from Matei
Pavaluca.
6) Allow for larger reordering levels in TCP, which are easily
achievable in the real world right now, from Eric Dumazet.
7) Add a variable of napi_schedule that doesn't need to disable cpu
interrupts, from Eric Dumazet.
8) Use a doubly linked list to optimize neigh_parms_release(), from
Nicolas Dichtel.
9) Various enhancements to the kernel BPF verifier, and allow eBPF
programs to actually be attached to sockets. From Alexei
Starovoitov.
10) Support TSO/LSO in sunvnet driver, from David L Stevens.
11) Allow controlling ECN usage via routing metrics, from Florian
Westphal.
12) Remote checksum offload, from Tom Herbert.
13) Add split-header receive, BQL, and xmit_more support to amd-xgbe
driver, from Thomas Lendacky.
14) Add MPLS support to openvswitch, from Simon Horman.
15) Support wildcard tunnel endpoints in ipv6 tunnels, from Steffen
Klassert.
16) Do gro flushes on a per-device basis using a timer, from Eric
Dumazet. This tries to resolve the conflicting goals between the
desired handling of bulk vs. RPC-like traffic.
17) Allow userspace to ask for the CPU upon what a packet was
received/steered, via SO_INCOMING_CPU. From Eric Dumazet.
18) Limit GSO packets to half the current congestion window, from Eric
Dumazet.
19) Add a generic helper so that all drivers set their RSS keys in a
consistent way, from Eric Dumazet.
20) Add xmit_more support to enic driver, from Govindarajulu
Varadarajan.
21) Add VLAN packet scheduler action, from Jiri Pirko.
22) Support configurable RSS hash functions via ethtool, from Eyal
Perry.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1820 commits)
Fix race condition between vxlan_sock_add and vxlan_sock_release
net/macb: fix compilation warning for print_hex_dump() called with skb->mac_header
net/mlx4: Add support for A0 steering
net/mlx4: Refactor QUERY_PORT
net/mlx4_core: Add explicit error message when rule doesn't meet configuration
net/mlx4: Add A0 hybrid steering
net/mlx4: Add mlx4_bitmap zone allocator
net/mlx4: Add a check if there are too many reserved QPs
net/mlx4: Change QP allocation scheme
net/mlx4_core: Use tasklet for user-space CQ completion events
net/mlx4_core: Mask out host side virtualization features for guests
net/mlx4_en: Set csum level for encapsulated packets
be2net: Export tunnel offloads only when a VxLAN tunnel is created
gianfar: Fix dma check map error when DMA_API_DEBUG is enabled
cxgb4/csiostor: Don't use MASTER_MUST for fw_hello call
net: fec: only enable mdio interrupt before phy device link up
net: fec: clear all interrupt events to support i.MX6SX
net: fec: reset fep link status in suspend function
net: sock: fix access via invalid file descriptor
net: introduce helper macro for_each_cmsghdr
...
As there are now no remaining users of arch_fast_hash(), lets kill
it entirely.
This basically reverts commit 71ae8aac3e ("lib: introduce arch
optimized hash library") and follow-up work, that is f.e., commit
237217546d ("lib: hash: follow-up fixups for arch hash"),
commit e3fec2f74f ("lib: Add missing arch generic-y entries for
asm-generic/hash.h") and last but not least commit 6a02652df5
("perf tools: Fix include for non x86 architectures").
Cc: Francesco Fusco <fusco@ntop.org>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While there normally is no reason to have a pull request for asm-generic
but have all changes get merged through whichever tree needs them, I do
have a series for 3.19. There are two sets of patches that change
significant portions of asm/io.h, and this branch contains both in order
to resolve the conflicts:
- Will Deacon has done a set of patches to ensure that all architectures
define {read,write}{b,w,l,q}_relaxed() functions or get them by
including asm-generic/io.h. These functions are commonly used on ARM
specific drivers to avoid expensive L2 cache synchronization implied by
the normal {read,write}{b,w,l,q}, but we need to define them on all
architectures in order to share the drivers across architectures and
to enable CONFIG_COMPILE_TEST configurations for them
- Thierry Reding has done an unrelated set of patches that extends
the asm-generic/io.h file to the degree necessary to make it useful
on ARM64 and potentially other architectures.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xUv6
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic asm/io.h rewrite from Arnd Bergmann:
"While there normally is no reason to have a pull request for
asm-generic but have all changes get merged through whichever tree
needs them, I do have a series for 3.19.
There are two sets of patches that change significant portions of
asm/io.h, and this branch contains both in order to resolve the
conflicts:
- Will Deacon has done a set of patches to ensure that all
architectures define {read,write}{b,w,l,q}_relaxed() functions or
get them by including asm-generic/io.h.
These functions are commonly used on ARM specific drivers to avoid
expensive L2 cache synchronization implied by the normal
{read,write}{b,w,l,q}, but we need to define them on all
architectures in order to share the drivers across architectures
and to enable CONFIG_COMPILE_TEST configurations for them
- Thierry Reding has done an unrelated set of patches that extends
the asm-generic/io.h file to the degree necessary to make it useful
on ARM64 and potentially other architectures"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (29 commits)
ARM64: use GENERIC_PCI_IOMAP
sparc: io: remove duplicate relaxed accessors on sparc32
ARM: sa11x0: Use void __iomem * in MMIO accessors
arm64: Use include/asm-generic/io.h
ARM: Use include/asm-generic/io.h
asm-generic/io.h: Implement generic {read,write}s*()
asm-generic/io.h: Reconcile I/O accessor overrides
/dev/mem: Use more consistent data types
Change xlate_dev_{kmem,mem}_ptr() prototypes
ARM: ixp4xx: Properly override I/O accessors
ARM: ixp4xx: Fix build with IXP4XX_INDIRECT_PCI
ARM: ebsa110: Properly override I/O accessors
ARC: Remove redundant PCI_IOBASE declaration
documentation: memory-barriers: clarify relaxed io accessor semantics
x86: io: implement dummy relaxed accessor macros for writes
tile: io: implement dummy relaxed accessor macros for writes
sparc: io: implement dummy relaxed accessor macros for writes
powerpc: io: implement dummy relaxed accessor macros for writes
parisc: io: implement dummy relaxed accessor macros for writes
mn10300: io: implement dummy relaxed accessor macros for writes
...
Replace PAGE_KERNEL with PAGE_KERNEL_EXEC to allow copy_to_user_page
invalidate icache for pages mapped with kmap.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
introduce new setsockopt() command:
setsockopt(sock, SOL_SOCKET, SO_ATTACH_BPF, &prog_fd, sizeof(prog_fd))
where prog_fd was received from syscall bpf(BPF_PROG_LOAD, attr, ...)
and attr->prog_type == BPF_PROG_TYPE_SOCKET_FILTER
setsockopt() calls bpf_prog_get() which increments refcnt of the program,
so it doesn't get unloaded while socket is using the program.
The same eBPF program can be attached to multiple sockets.
User task exit automatically closes socket which calls sk_filter_uncharge()
which decrements refcnt of eBPF program
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/chelsio/cxgb4vf/sge.c
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
sge.c was overlapping two changes, one to use the new
__dev_alloc_page() in net-next, and one to use s->fl_pg_order in net.
ixgbe_phy.c was a set of overlapping whitespace changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Alternative to RPS/RFS is to use hardware support for multiple
queues.
Then split a set of million of sockets into worker threads, each
one using epoll() to manage events on its own socket pool.
Ideally, we want one thread per RX/TX queue/cpu, but we have no way to
know after accept() or connect() on which queue/cpu a socket is managed.
We normally use one cpu per RX queue (IRQ smp_affinity being properly
set), so remembering on socket structure which cpu delivered last packet
is enough to solve the problem.
After accept(), connect(), or even file descriptor passing around
processes, applications can use :
int cpu;
socklen_t len = sizeof(cpu);
getsockopt(fd, SOL_SOCKET, SO_INCOMING_CPU, &cpu, &len);
And use this information to put the socket into the right silo
for optimal performance, as all networking stack should run
on the appropriate cpu, without need to send IPI (RPS/RFS).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- add seccomp, getrandom, and memfd_create syscalls;
- add defconfigs for KC705 and SMP LX200;
- fix ISS and xtfpga Kconfig dependencies so that more randconfigs
are buildable;
- fix umount syscall;
- implement pgprot_noncached.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=F6y4
-----END PGP SIGNATURE-----
Merge tag 'xtensa-for-next-20141021-1' of git://github.com/jcmvbkbc/linux-xtensa into for_next
Xtensa improvements for 3.18:
- add seccomp, getrandom, and memfd_create syscalls;
- add defconfigs for KC705 and SMP LX200;
- fix ISS and xtfpga Kconfig dependencies so that more randconfigs
are buildable;
- fix umount syscall;
- implement pgprot_noncached.
The Stretch s6000 family support has been merged into mainline 5 years
ago. There appear to be no users of this code since nobody complained
that there is a merge error preventing compilation.
Apart from the s6105 IP camera reference design there are no s6000 devices
known to ever have run Linux and as the chips are out of production there
probably never will be. The successor s7000 no longer uses an Xtensa core
for the OS.
Let's remove the code until someone is found who actually needs it.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
noMMU configuration doesn't use special area for vmalloc allocations,
don't print it in the memory map.
PAGE_OFFSET is fixed to 0 in noMMU, use min_low_pfn and max_low_pfn for
lowmem range display.
Make all XCHAL_KSEG_* constants unsigned long for consistency with other
addresses.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Memory accounting code can't handle pages below
PLATFORM_DEFAULT_MEM_START. Reserve those pages if they exist.
When PLATFORM_DEFAULT_MEM_START is zero reserve one page at address 0 to
make sure that successfull memory allocations don't return NULL.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
initialize_mmu sets up atomctl SR which is needed for s32c1i to function
correctly even in noMMU configurations. It's also a good place to set up
caching attributes of physical memory.
Allow enabling INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX in noMMU
configurations for setting up atomctl and cache attributes.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Instead of initializing vecbase in initialize_mmu macro, which may be
expanded either in Image.elf reset vector hadler or in the kernel
head.S, both times only when CONFIG_MMU is enabled, do this
initialization once in _startup function.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Use the same offset from the default physical memory start address as in
LOAD_MEMORY_ADDRESS definition.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Change KERNELOFFSET, LOAD_MEMORY_ADDRESS and VIRTUAL_MEMORY_ADDRESS to be
relative to the start of physical memory in noMMU configuration, as
there's no uniform memory remapping to KSEG starting at 0xd0000000.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Don't hardcode kernel entry address as 0x3000 or 0xd0003000, use
LOAD_MEMORY_ADDRESS macro. Don't compile MMU remapping code and don't try
to link it when building noMMU configuration.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
This config allows running SMP-enabled bitstream on LX200 board.
NFS or FLASH rootfs, minimal debug, up to 4 cores.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Userspace actually passes single parameter (path name) to the umount
syscall, so new umount just fails. Fix it by requesting old umount
syscall implementation and re-wiring umount to it.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
These are now defined by asm-generic/io.h, so we don't need the private
definitions anymore.
Cc: Chris Zankel <chris@zankel.net>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Pull audit updates from Eric Paris:
"So this change across a whole bunch of arches really solves one basic
problem. We want to audit when seccomp is killing a process. seccomp
hooks in before the audit syscall entry code. audit_syscall_entry
took as an argument the arch of the given syscall. Since the arch is
part of what makes a syscall number meaningful it's an important part
of the record, but it isn't available when seccomp shoots the
syscall...
For most arch's we have a better way to get the arch (syscall_get_arch)
So the solution was two fold: Implement syscall_get_arch() everywhere
there is audit which didn't have it. Use syscall_get_arch() in the
seccomp audit code. Having syscall_get_arch() everywhere meant it was
a useless flag on the stack and we could get rid of it for the typical
syscall entry.
The other changes inside the audit system aren't grand, fixed some
records that had invalid spaces. Better locking around the task comm
field. Removing some dead functions and structs. Make some things
static. Really minor stuff"
* git://git.infradead.org/users/eparis/audit: (31 commits)
audit: rename audit_log_remove_rule to disambiguate for trees
audit: cull redundancy in audit_rule_change
audit: WARN if audit_rule_change called illegally
audit: put rule existence check in canonical order
next: openrisc: Fix build
audit: get comm using lock to avoid race in string printing
audit: remove open_arg() function that is never used
audit: correct AUDIT_GET_FEATURE return message type
audit: set nlmsg_len for multicast messages.
audit: use union for audit_field values since they are mutually exclusive
audit: invalid op= values for rules
audit: use atomic_t to simplify audit_serial()
kernel/audit.c: use ARRAY_SIZE instead of sizeof/sizeof[0]
audit: reduce scope of audit_log_fcaps
audit: reduce scope of audit_net_id
audit: arm64: Remove the audit arch argument to audit_syscall_entry
arm64: audit: Add audit hook in syscall_trace_enter/exit()
audit: x86: drop arch from __audit_syscall_entry() interface
sparc: implement is_32bit_task
sparc: properly conditionalize use of TIF_32BIT
...
Pull arch atomic cleanups from Ingo Molnar:
"This is a series kept separate from the main locking tree, which
cleans up and improves various details in the atomics type handling:
- Remove the unused atomic_or_long() method
- Consolidate and compress atomic ops implementations between
architectures, to reduce linecount and to make it easier to add new
ops.
- Rewrite generic atomic support to only require cmpxchg() from an
architecture - generate all other methods from that"
* 'locking-arch-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
locking,arch: Use ACCESS_ONCE() instead of cast to volatile in atomic_read()
locking, mips: Fix atomics
locking, sparc64: Fix atomics
locking,arch: Rewrite generic atomic support
locking,arch,xtensa: Fold atomic_ops
locking,arch,sparc: Fold atomic_ops
locking,arch,sh: Fold atomic_ops
locking,arch,powerpc: Fold atomic_ops
locking,arch,parisc: Fold atomic_ops
locking,arch,mn10300: Fold atomic_ops
locking,arch,mips: Fold atomic_ops
locking,arch,metag: Fold atomic_ops
locking,arch,m68k: Fold atomic_ops
locking,arch,m32r: Fold atomic_ops
locking,arch,ia64: Fold atomic_ops
locking,arch,hexagon: Fold atomic_ops
locking,arch,cris: Fold atomic_ops
locking,arch,avr32: Fold atomic_ops
locking,arch,arm64: Fold atomic_ops
locking,arch,arm: Fold atomic_ops
...
Pull timer fixes from Ingo Molnar:
"Main changes:
- Fix the deadlock reported by Dave Jones et al
- Clean up and fix nohz_full interaction with arch abilities
- nohz init code consolidation/cleanup"
* 'timers-nohz-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
nohz: nohz full depends on irq work self IPI support
nohz: Consolidate nohz full init code
arm64: Tell irq work about self IPI support
arm: Tell irq work about self IPI support
x86: Tell irq work about self IPI support
irq_work: Force raised irq work to run on irq work interrupt
irq_work: Introduce arch_irq_work_has_interrupt()
nohz: Move nohz full init call to tick init
Otherwise we get the following build warning:
(XTENSA_PLATFORM_XTFPGA) selects ETHOC which has unmet direct
dependencies (NETDEVICES && ETHERNET && HAS_IOMEM && HAS_DMA)
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
The default pgprot_noncached doesn't do anything. This leads to issues
when drivers rely on it to disable caching in userspace mappings.
Implement pgprot_noncached properly so that caching of userspace mappings
could be controlled.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Use the much more reader friendly ACCESS_ONCE() instead of the cast to volatile.
This is purely a stylistic change.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-arch@vger.kernel.org
Link: http://lkml.kernel.org/r/1411482607-20948-1-git-send-email-bobby.prani@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The nohz full code needs irq work to trigger its own interrupt so that
the subsystem can work even when the tick is stopped.
Lets introduce arch_irq_work_has_interrupt() that archs can override to
tell about their support for this ability.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Commit: e676253b19 [3/21] serial/8250: Add
support for RS485 IOCTLs, adds support for RS485 ioctls for 825_core on
all the archs. Unfortunaltely the definition of TIOCSRS485 and
TIOCGRS485 was missing on the ioctls.h file
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- support highmem on cores with aliasing data cache. Enable highmem on kc705
by default;
- simplify addition of new core variants (no need to modify Kconfig /
Makefiles);
- improve robustness of unaligned access handler and its interaction with
window overflow/underflow exception handlers;
- deprecate atomic and spill registers syscalls;
- clean up Kconfig: remove orphan MATH_EMULATION, sort 'select' statements;
- wire up renameat2 syscall.
Various fixes:
- fix address checks in dma_{alloc,free}_coherent (runtime BUG);
- fix access to THREAD_RA/THREAD_SP/THREAD_DS (debug build breakage);
- fix TLBTEMP_BASE_2 region handling in fast_second_level_miss (runtime
unrecoverable exception);
- fix a6 and a7 handling in fast_syscall_xtensa (runtime userspace register
clobbering);
- fix kernel/user jump out of fast_unaligned (potential runtime unrecoverabl
exception);
- replace termios IOCTL code definitions with constants (userspace build
breakage).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=mAYX
-----END PGP SIGNATURE-----
Merge tag 'xtensa-20140830' of git://github.com/czankel/xtensa-linux
Pull Xtensa updates from Chris Zankel:
"Xtensa improvements for 3.17:
- support highmem on cores with aliasing data cache. Enable highmem
on kc705 by default
- simplify addition of new core variants (no need to modify Kconfig /
Makefiles)
- improve robustness of unaligned access handler and its interaction
with window overflow/underflow exception handlers
- deprecate atomic and spill registers syscalls
- clean up Kconfig: remove orphan MATH_EMULATION, sort 'select'
statements
- wire up renameat2 syscall.
Various fixes:
- fix address checks in dma_{alloc,free}_coherent (runtime BUG)
- fix access to THREAD_RA/THREAD_SP/THREAD_DS (debug build breakage)
- fix TLBTEMP_BASE_2 region handling in fast_second_level_miss
(runtime unrecoverable exception)
- fix a6 and a7 handling in fast_syscall_xtensa (runtime userspace
register clobbering)
- fix kernel/user jump out of fast_unaligned (potential runtime
unrecoverabl exception)
- replace termios IOCTL code definitions with constants (userspace
build breakage)"
* tag 'xtensa-20140830' of git://github.com/czankel/xtensa-linux: (25 commits)
xtensa: deprecate fast_xtensa and fast_spill_registers syscalls
xtensa: don't allow overflow/underflow on unaligned stack
xtensa: fix a6 and a7 handling in fast_syscall_xtensa
xtensa: allow single-stepping through unaligned load/store
xtensa: move invalid unaligned instruction handler closer to its users
xtensa: make fast_unaligned store restartable
xtensa: add double exception fixup handler for fast_unaligned
xtensa: fix kernel/user jump out of fast_unaligned
xtensa: configure kc705 for highmem
xtensa: support highmem in aliasing cache flushing code
xtensa: support aliasing cache in kmap
xtensa: support aliasing cache in k[un]map_atomic
xtensa: implement clear_user_highpage and copy_user_highpage
xtensa: fix TLBTEMP_BASE_2 region handling in fast_second_level_miss
xtensa: allow fixmap and kmap span more than one page table
xtensa: make fixmap region addressing grow with index
xtensa: fix access to THREAD_RA/THREAD_SP/THREAD_DS
xtensa: add renameat2 syscall
xtensa: fix address checks in dma_{alloc,free}_coherent
xtensa: replace IOCTL code definitions with constants
...
- support highmem on cores with aliasing data cache. Enable highmem on kc705
by default;
- simplify addition of new core variants (no need to modify Kconfig /
Makefiles);
- improve robustness of unaligned access handler and its interaction with
window overflow/underflow exception handlers;
- deprecate atomic and spill registers syscalls;
- clean up Kconfig: remove orphan MATH_EMULATION, sort 'select' statements;
- wire up renameat2 syscall.
Various fixes:
- fix address checks in dma_{alloc,free}_coherent (runtime BUG);
- fix access to THREAD_RA/THREAD_SP/THREAD_DS (debug build breakage);
- fix TLBTEMP_BASE_2 region handling in fast_second_level_miss (runtime
unrecoverable exception);
- fix a6 and a7 handling in fast_syscall_xtensa (runtime userspace register
clobbering);
- fix kernel/user jump out of fast_unaligned (potential runtime unrecoverable
exception);
- replace termios IOCTL code definitions with constants (userspace build
breakage).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=q9be
-----END PGP SIGNATURE-----
Merge tag 'xtensa-for-next-20140815' into for_next
Xtensa improvements for 3.17:
- support highmem on cores with aliasing data cache. Enable highmem on kc705
by default;
- simplify addition of new core variants (no need to modify Kconfig /
Makefiles);
- improve robustness of unaligned access handler and its interaction with
window overflow/underflow exception handlers;
- deprecate atomic and spill registers syscalls;
- clean up Kconfig: remove orphan MATH_EMULATION, sort 'select' statements;
- wire up renameat2 syscall.
Various fixes:
- fix address checks in dma_{alloc,free}_coherent (runtime BUG);
- fix access to THREAD_RA/THREAD_SP/THREAD_DS (debug build breakage);
- fix TLBTEMP_BASE_2 region handling in fast_second_level_miss (runtime
unrecoverable exception);
- fix a6 and a7 handling in fast_syscall_xtensa (runtime userspace register
clobbering);
- fix kernel/user jump out of fast_unaligned (potential runtime unrecoverable
exception);
- replace termios IOCTL code definitions with constants (userspace build
breakage).
Signed-off-by: Chris Zankel <chris@zankel.net>
Many of the atomic op implementations are the same except for one
instruction; fold the lot into a few CPP macros and reduce LoC.
This also prepares for easy addition of new ops.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: linux-xtensa@linux-xtensa.org
Link: http://lkml.kernel.org/r/20140508135852.879575796@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
These syscalls are not used by userspace tools for some time now, and
they have issues when called with invalid arguments. It's not worth
changing signal delivery mechanism as we don't expect any new users for
these syscalls. Let's keep them for backwards compatibility under #ifdef,
disabled by default.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Double exceptions that happen during register window overflow/underflow
are handled in the topmost stack frame, as if it was the only exception
that occured. However unaligned access exception handler is special
because it needs to analyze instruction that caused the exception, but
the userspace instruction that triggered window exception is completely
irrelevant. Unaligned data access is rather normal in the generic
userspace code, but stack pointer manipulation must always be done by
architecture-aware code and thus unaligned stack means a serious problem
anyway.
Use the default unaligned access handler that raises SIGBUS in case
of unaligned access in window overflow/underflow handler.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Remove restoring a6 on some return paths and instead modify and restore
it in a single place, using symbolic name.
Correctly restore a7 from PT_AREG7 in case of illegal a6 value.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Update icount when icountlevel is non-zero but not greater than EXCM level
when load/store instruction is successfully emulated. This allows
single-stepping over such instruction in userspace debugger.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
With this change a threaded jump from .Linvalid_instruction_load to
.Linvalid_instruction can be removed and more code may be added to
common load/store exit path.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
fast_unaligned may encounter DTLB miss or SEGFAULT during the store
emulation. Don't update epc1 and lcount until after the store emulation
is complete, so that the faulting store instruction could be replayed.
Remove duplicate code handling zero overhead loops and calculate new
epc1 and lcount in one place.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
fast_unaligned_fixup restores user registers and runs normal exception
handler in the current stack frame. Unaligned load/store is retried
after that.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Enable all memory available on KC705 (1G - 128M) by default. Update memory
node in DTS and also limit usable memory in bootargs in case memmap is
passed from the bootloader.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Use __flush_invalidate_dcache_page_alias with alias set to color of the
page physical address instead of __flush_invalidate_dcache_page: this
works for high memory pages and mapping/unmapping to the TLBTEMP area is
virtually free.
Allow building configurations with aliasing cache and highmem enabled.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Define ARCH_PKMAP_COLORING and provide corresponding macro definitions
on cores with aliasing data cache.
Instead of single last_pkmap_nr maintain an array last_pkmap_nr_arr of
pkmap counters for each page color. Make sure that kmap maps physical
page at virtual address with color matching its physical address.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Map high memory pages at virtual addresses with color that match color
of their physical address. Existing cache alias management mechanisms
may be used with such pages.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Existing clear_user_page and copy_user_page cannot be used with highmem
because they calculate physical page address from its virtual address
and do it incorrectly in case of high memory page mapped with
kmap_atomic. Also kmap is not needed, as most likely userspace mapping
color would be different from the kmapped color.
Provide clear_user_highpage and copy_user_highpage functions that
determine if temporary mapping is needed for the pages. Move most of the
logic of the former clear_user_page and copy_user_page to
xtensa/mm/cache.c only leaving temporary mapping setup, invalidation and
clearing/copying in the xtensa/mm/misc.S. Rename these functions to
clear_page_alias and copy_page_alias.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Current definition of TLBTEMP_BASE_2 is always 32K above the
TLBTEMP_BASE_1, whereas fast_second_level_miss handler for the TLBTEMP
region analyzes virtual address bit (PAGE_SHIFT + DCACHE_ALIAS_ORDER)
to determine TLBTEMP region where the fault happened. The size of the
TLBTEMP region is also checked incorrectly: not 64K, but twice data
cache way size (whicht may as well be less than the instruction cache
way size).
Fix TLBTEMP_BASE_2 to be TLBTEMP_BASE_1 + data cache way size.
Provide TLBTEMP_SIZE that is a greater of doubled data cache way size or
the instruction cache way size, and use it to determine if the second
level TLB miss occured in the TLBTEMP region.
Practical occurence of page faults in the TLBTEMP area is extremely
rare, this code can be tested by deletion of all w[di]tlb instructions
in the tlbtemp_mapping region.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
To support aliasing cache both kmap region sizes are multiplied by the
number of data cache colors. After that expansion page tables that cover
kmap regions may become larger than one page. Correctly allocate and
initialize page tables in this case.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
It's much easier to reason about alignment and coloring of regions
located in the fixmap when fixmap index is just a PFN within the fixmap
region. Change fixmap addressing so that index 0 corresponds to
FIXADDR_START instead of the FIXADDR_TOP.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
With SMP and a lot of debug options enabled task_struct::thread gets out
of reach of s32i/l32i instructions with base pointing at task_struct,
breaking build with the following messages:
arch/xtensa/kernel/entry.S: Assembler messages:
arch/xtensa/kernel/entry.S:1002: Error: operand 3 of 'l32i.n' has invalid value '1048'
arch/xtensa/kernel/entry.S:1831: Error: operand 3 of 's32i.n' has invalid value '1040'
arch/xtensa/kernel/entry.S:1832: Error: operand 3 of 's32i.n' has invalid value '1044'
Change base to point to task_struct::thread in such cases.
Don't use a10 in _switch_to to save/restore prev pointer as a2 is not
clobbered.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Virtual address is translated to the XCHAL_KSEG_CACHED region in the
dma_free_coherent, but is checked to be in the 0...XCHAL_KSEG_SIZE
range.
Change check for end of the range from 'addr >= X' to 'addr > X - 1' to
handle the case of X == 0.
Replace 'if (C) BUG();' construct with 'BUG_ON(C);'.
Cc: stable@vger.kernel.org
Signed-off-by: Alan Douglas <adouglas@cadence.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
This fixes userspace code that builds on other architectures but fails
on xtensa due to references to structures that other architectures don't
refer to. E.g. this fixes the following issue with python-2.7.8:
python-2.7.8/Modules/termios.c:861:25: error: invalid application
of 'sizeof' to incomplete type 'struct serial_multiport_struct'
{"TIOCSERGETMULTI", TIOCSERGETMULTI},
python-2.7.8/Modules/termios.c:870:25: error: invalid application
of 'sizeof' to incomplete type 'struct serial_multiport_struct'
{"TIOCSERSETMULTI", TIOCSERSETMULTI},
python-2.7.8/Modules/termios.c:900:24: error: invalid application
of 'sizeof' to incomplete type 'struct tty_struct'
{"TIOCTTYGSTRUCT", TIOCTTYGSTRUCT},
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Instead of adding new Kconfig options and Makefile rules for each new
core variant provide XTENSA_VARIANT_CUSTOM variant and record variant
name in the XTENSA_VARIANT_NAME variable. Adding new core variant now
means providing directory structure under arch/xtensa/variant and
specifying correct name in kernel configuration.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Pull arch signal handling cleanup from Richard Weinberger:
"This patch series moves all remaining archs to the get_signal(),
signal_setup_done() and sigsp() functions.
Currently these archs use open coded variants of the said functions.
Further, unused parameters get removed from get_signal_to_deliver(),
tracehook_signal_handler() and signal_delivered().
At the end of the day we save around 500 lines of code."
* 'signal-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/misc: (43 commits)
powerpc: Use sigsp()
openrisc: Use sigsp()
mn10300: Use sigsp()
mips: Use sigsp()
microblaze: Use sigsp()
metag: Use sigsp()
m68k: Use sigsp()
m32r: Use sigsp()
hexagon: Use sigsp()
frv: Use sigsp()
cris: Use sigsp()
c6x: Use sigsp()
blackfin: Use sigsp()
avr32: Use sigsp()
arm64: Use sigsp()
arc: Use sigsp()
sas_ss_flags: Remove nested ternary if
Rip out get_signal_to_deliver()
Clean up signal_delivered()
tracehook_signal_handler: Remove sig, info, ka and regs
...
Pull locking updates from Ingo Molnar:
"The main changes in this cycle are:
- big rtmutex and futex cleanup and robustification from Thomas
Gleixner
- mutex optimizations and refinements from Jason Low
- arch_mutex_cpu_relax() removal and related cleanups
- smaller lockdep tweaks"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
arch, locking: Ciao arch_mutex_cpu_relax()
locking/lockdep: Only ask for /proc/lock_stat output when available
locking/mutexes: Optimize mutex trylock slowpath
locking/mutexes: Try to acquire mutex only if it is unlocked
locking/mutexes: Delete the MUTEX_SHOW_NO_WAITER macro
locking/mutexes: Correct documentation on mutex optimistic spinning
rtmutex: Make the rtmutex tester depend on BROKEN
futex: Simplify futex_lock_pi_atomic() and make it more robust
futex: Split out the first waiter attachment from lookup_pi_state()
futex: Split out the waiter check from lookup_pi_state()
futex: Use futex_top_waiter() in lookup_pi_state()
futex: Make unlock_pi more robust
rtmutex: Avoid pointless requeueing in the deadlock detection chain walk
rtmutex: Cleanup deadlock detector debug logic
rtmutex: Confine deadlock logic to futex
rtmutex: Simplify remove_waiter()
rtmutex: Document pi chain walk
rtmutex: Clarify the boost/deboost part
rtmutex: No need to keep task ref for lock owner check
rtmutex: Simplify and document try_to_take_rtmutex()
...
The arch_mutex_cpu_relax() function, introduced by 34b133f, is
hacky and ugly. It was added a few years ago to address the fact
that common cpu_relax() calls include yielding on s390, and thus
impact the optimistic spinning functionality of mutexes. Nowadays
we use this function well beyond mutexes: rwsem, qrwlock, mcs and
lockref. Since the macro that defines the call is in the mutex header,
any users must include mutex.h and the naming is misleading as well.
This patch (i) renames the call to cpu_relax_lowlatency ("relax, but
only if you can do it with very low latency") and (ii) defines it in
each arch's asm/processor.h local header, just like for regular cpu_relax
functions. On all archs, except s390, cpu_relax_lowlatency is simply cpu_relax,
and thus we can take it out of mutex.h. While this can seem redundant,
I believe it is a good choice as it allows us to move out arch specific
logic from generic locking primitives and enables future(?) archs to
transparently define it, similarly to System Z.
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Bharat Bhushan <r65777@freescale.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: David Howells <dhowells@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Cc: Dominik Dingel <dingel@linux.vnet.ibm.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Joe Perches <joe@perches.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Joseph Myers <joseph@codesourcery.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Nicolas Pitre <nico@linaro.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Qiaowei Ren <qiaowei.ren@intel.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: Stratos Karafotis <stratosk@semaphore.gr>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vasily Kulikov <segoon@openwall.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Cc: Waiman Long <Waiman.Long@hp.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: adi-buildroot-devel@lists.sourceforge.net
Cc: linux390@de.ibm.com
Cc: linux-alpha@vger.kernel.org
Cc: linux-am33-list@redhat.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-c6x-dev@linux-c6x.org
Cc: linux-cris-kernel@axis.com
Cc: linux-hexagon@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
Cc: linux@lists.openrisc.net
Cc: linux-m32r-ja@ml.linux-m32r.org
Cc: linux-m32r@ml.linux-m32r.org
Cc: linux-m68k@lists.linux-m68k.org
Cc: linux-metag@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-parisc@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-s390@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: linux-xtensa@linux-xtensa.org
Cc: sparclinux@vger.kernel.org
Link: http://lkml.kernel.org/r/1404079773.2619.4.camel@buesod1.americas.hpqcorp.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- resolve FIXMEs in double exception handler for window overflow. This
fix makes native building of linux on xtensa host possible;
- fix sysmem region removal issue introduced in 3.15.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R7uM
-----END PGP SIGNATURE-----
Merge tag 'xtensa-for-next-20140715' of git://github.com/jcmvbkbc/linux-xtensa into for_next
Xtensa fixes for 3.16:
- resolve FIXMEs in double exception handler for window overflow. This
fix makes native building of linux on xtensa host possible;
- fix sysmem region removal issue introduced in 3.15.
When sysmem reservation occurs exactly at the end of an existing block
that block is deleted, because it is incorrectly included in the range
of memblocks to remove. Fix that by skipping such block.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
There are two FIXMEs in the double exception handler 'for the extremely
unlikely case'. This case gets hit by gcc during kernel build once in
a few hours, resulting in an unrecoverable exception condition.
Provide missing fixup routine to handle this case. Double exception
literals now need 8 more bytes, add them to the linker script.
Also replace bbsi instructions with bbsi.l as we're branching depending
on 8th and 7th LSB-based bits of exception address.
This may be tested by adding the explicit DTLB invalidation to window
overflow handlers, like the following:
--- a/arch/xtensa/kernel/vectors.S
+++ b/arch/xtensa/kernel/vectors.S
@@ -592,6 +592,14 @@ ENDPROC(_WindowUnderflow4)
ENTRY_ALIGN64(_WindowOverflow8)
s32e a0, a9, -16
+ bbsi.l a9, 31, 1f
+ rsr a0, ccount
+ bbsi.l a0, 4, 1f
+ pdtlb a0, a9
+ idtlb a0
+ movi a0, 9
+ idtlb a0
+1:
l32e a0, a1, -12
s32e a2, a9, -8
s32e a1, a9, -12
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Strings library contributed to glibc but re-licensed under GPLv2)
- Optimised crypto algorithms making use of the ARMv8 crypto extensions
(together with kernel API for using FPSIMD instructions in interrupt
context)
- Ftrace support
- CPU topology parsing from DT
- ESR_EL1 (Exception Syndrome Register) exposed to user space signal
handlers for SIGSEGV/SIGBUS (useful to emulation tools like Qemu)
- 1GB section linear mapping if applicable
- Barriers usage clean-up
- Default pgprot clean-up
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=Jj8U
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux into next
Pull arm64 updates from Catalin Marinas:
- Optimised assembly string/memory routines (based on the AArch64
Cortex Strings library contributed to glibc but re-licensed under
GPLv2)
- Optimised crypto algorithms making use of the ARMv8 crypto extensions
(together with kernel API for using FPSIMD instructions in interrupt
context)
- Ftrace support
- CPU topology parsing from DT
- ESR_EL1 (Exception Syndrome Register) exposed to user space signal
handlers for SIGSEGV/SIGBUS (useful to emulation tools like Qemu)
- 1GB section linear mapping if applicable
- Barriers usage clean-up
- Default pgprot clean-up
Conflicts as per Catalin.
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (57 commits)
arm64: kernel: initialize broadcast hrtimer based clock event device
arm64: ftrace: Add system call tracepoint
arm64: ftrace: Add CALLER_ADDRx macros
arm64: ftrace: Add dynamic ftrace support
arm64: Add ftrace support
ftrace: Add arm64 support to recordmcount
arm64: Add 'notrace' attribute to unwind_frame() for ftrace
arm64: add __ASSEMBLY__ in asm/insn.h
arm64: Fix linker script entry point
arm64: lib: Implement optimized string length routines
arm64: lib: Implement optimized string compare routines
arm64: lib: Implement optimized memcmp routine
arm64: lib: Implement optimized memset routine
arm64: lib: Implement optimized memmove routine
arm64: lib: Implement optimized memcpy routine
arm64: defconfig: enable a few more common/useful options in defconfig
ftrace: Make CALLER_ADDRx macros more generic
arm64: Fix deadlock scenario with smp_send_stop()
arm64: Fix machine_shutdown() definition
arm64: Support arch_irq_work_raise() via self IPIs
...
- Another round of clean-up of FDT related code in architecture code.
This removes knowledge of internal FDT details from most architectures
except powerpc.
- Conversion of kernel's custom FDT parsing code to use libfdt.
- DT based initialization for generic serial earlycon. The introduction
of generic serial earlycon support went in thru tty tree.
- Improve the platform device naming for DT probed devices to ensure
unique naming and use parent names instead of a global index.
- Fix a race condition in of_update_property.
- Unify the various linker section OF match tables and fix several
function prototype errors.
- Update platform_get_irq_byname to work in deferred probe cases.
- 2 binding doc updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTjzgyAAoJEMhvYp4jgsXiFsUH/1PMTGo8CyD62VQD5ZKdAoW+
Fq6vCiRQ8assF5i5ZLcW1DqhjtoRaCKYhVbRKa5lj7cZdjlSpacI/qQPrF5Br2Ii
bTE3Ff/AQwipQaz/Bj7HqJCgGwfWK8xdfgW0abKsyXMWDN86Bov/zzeu8apmws0x
H1XjJRgnc/rzM4m9ny6+lss0iq6YL54SuTYNzHR33+Ywxls69SfHXIhCW0KpZcBl
5U3YUOomt40GfO46sxFA4xApAhypEK4oVq7asyiA2ArTZ/c2Pkc9p5CBqzhDLmlq
yioWTwHIISv0q+yMLCuQrVGIsbUDkQyy7RQ15z6U+/e/iGO/M+j3A5yxMc3qOi4=
=Onff
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux into next
Pull DeviceTree updates from Rob Herring:
- Another round of clean-up of FDT related code in architecture code.
This removes knowledge of internal FDT details from most
architectures except powerpc.
- Conversion of kernel's custom FDT parsing code to use libfdt.
- DT based initialization for generic serial earlycon. The
introduction of generic serial earlycon support went in through the
tty tree.
- Improve the platform device naming for DT probed devices to ensure
unique naming and use parent names instead of a global index.
- Fix a race condition in of_update_property.
- Unify the various linker section OF match tables and fix several
function prototype errors.
- Update platform_get_irq_byname to work in deferred probe cases.
- 2 binding doc updates
* tag 'devicetree-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (58 commits)
of: handle NULL node in next_child iterators
of/irq: provide more wrappers for !CONFIG_OF
devicetree: bindings: Document micrel vendor prefix
dt: bindings: dwc2: fix required value for the phy-names property
of_pci_irq: kill useless variable in of_irq_parse_pci()
of/irq: do irq resolution in platform_get_irq_byname()
of: Add a testcase for of_find_node_by_path()
of: Make of_find_node_by_path() handle /aliases
of: Create unlocked version of for_each_child_of_node()
lib: add glibc style strchrnul() variant
of: Handle memory@0 node on PPC32 only
pci/of: Remove dead code
of: fix race between search and remove in of_update_property()
of: Use NULL for pointers
of: Stop naming platform_device using dcr address
of: Ensure unique names without sacrificing determinism
tty/serial: pl011: add DT based earlycon support
of/fdt: add FDT serial scanning for earlycon
of/fdt: add FDT address translation support
serial: earlycon: add DT support
...
Max Filippov
Dan Williams
Ingo Molnar
Viresh Kumar
Thomas Gleixner
Christoph Hellwig
Jiang Liu
Peter Zijlstra
Lorenzo Pieralisi
Davidlohr Bueso
Laurent Dufour
Chris Metcalf
Linus Torvalds
Akinobu Mita
Paul Gortmaker
Toshi Kani
Masanari Iida
Guenter Roeck
David Hildenbrand
Chris Zankel
Richard Weinberger
Al Viro
Yijing Wang
Tejun Heo
Andy Lutomirski
Kirill A. Shutemov
Michael S. Tsirkin
Daniel Borkmann
Alexei Starovoitov
David S. Miller
Eric Dumazet
Daniel Glöckner
Will Deacon
Pranith Kumar
Eric Paris
Ricardo Ribalda Delgado
Miklos Szeredi
Alan Douglas
Davidlohr Bueso