fs/cachefiles/rdwr.c: In function ‘cachefiles_write_page’:
fs/cachefiles/rdwr.c:882: warning: ‘ret’ may be used uninitialized in
this function
If the jump to label "error" is taken, "ret" will indeed be
uninitialized, and random stack data may be printed by the debug code.
Fixes: 102f4d900c ("FS-Cache: Handle a write to the page immediately beyond the EOF marker")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Now that IP1000A chips are supported by dl2k driver, the buggy ipg
driver can be removed.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for IP1000A chips to dl2k driver.
IP1000A chip looks like a TC9020 with integrated PHY.
This allows IP1000A chips to work reliably because the ipg driver is
buggy - it loses packets under load and then completely stops
transmitting data.
Tested with Asus NX1101 v2.0 at 10, 100 and 1000Mbps:
vendor=0x13f0 device=0x1023 (rev 0x41)
subsystem vendor=0x1043 device=0x8180
MAC address registers access needed to be changed from 8-bit to 16-bit
because 8-bit does not work on IP1000A. 8-bit access is not even
allowed in the TC9020 datasheet (although it worked). 16-bit access
works on both.
Tested that it does not break D-Link DGE-550T (DL-2000 chip, probably
a rebranded TC9020):
vendor=0x1186 device=0x4000 (rev 0x0c)
subsystem vendor=0x1186 device=0x4000
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the OUTMCAST stat is double incremented, getting bumped once in the mcast code
itself, and again in the common ip output path. Remove the mcast bump, as its
not needed
Validated by the reporter, with good results
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Claus Jensen <claus.jensen@microsemi.com>
CC: Claus Jensen <claus.jensen@microsemi.com>
CC: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases the crash is caused by nicvf_remove() being called from
outside. For example, if we try to feed the device to vfio after the
probe has failed for some reason. So, move the check to better place.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent flaw in the netdev feature setting resulted in warnings
like this one from VLAN interfaces:
WARNING: CPU: 1 PID: 4975 at net/core/dev.c:2419 skb_warn_bad_offload+0xbc/0xcb()
: caps=(0x00000000001b5820, 0x00000000001b5829) len=2782 data_len=0 gso_size=1348 gso_type=16 ip_summed=3
The ":" is supposed to be preceded by a driver name, but in this
case it is an empty string since the device has no parent.
There are many types of network devices without a parent. The
anonymous warnings for these devices can be hard to debug. Log
the network device name instead in these cases to assist further
debugging.
This is mostly similar to how __netdev_printk() handles orphan
devices.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case multiple writes to a unix stream socket race we could end up in a
situation where we pre-allocate a new skb for use in unix_stream_sendpage
but have to free it again in the locked section because another skb
has been appended meanwhile, which we must use. Accidentally we didn't
clear the pointer after consuming it and so we touched freed memory
while appending it to the sk_receive_queue. So, clear the pointer after
consuming the skb.
This bug has been found with syzkaller
(http://github.com/google/syzkaller) by Dmitry Vyukov.
Fixes: 869e7c6248 ("net: af_unix: implement stream sendpage support")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl_fdb_dump always expects an index to be returned by the ndo_fdb_dump op,
but when CONFIG_NET_SWITCHDEV is off, it returns an error.
Fix that by returning the given unmodified idx.
A similar fix was 0890cf6cb6 ("switchdev: fix return value of
switchdev_port_fdb_dump in case of error") but for the CONFIG_NET_SWITCHDEV=y
case.
Fixes: 45d4122ca7 ("switchdev: add support for fdb add/del/dump via switchdev_port_obj ops.")
Signed-off-by: Dragos Tatulea <dragos@endocode.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 05cc5a39dd "bnx2x: add vlan filtering offload" introduced
a regression in regard for vlans for 57710, 57711 adapters -
Loading 8021q module on a machine with such an adapter would cause
a null pointer dereference, as the driver mistakenly publishes it
has capabilities for vlan CTAG filtering.
Reported-by: Otto Sabart <osabart@redhat.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver does not handle the AVB-DMAC Receive FIFO Warning interrupt
now, so the interrupt should not be enabled.
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sending ICMP packets with raw sockets ends up in the SNMP counters
logging the type as the first byte of the IPv4 header rather than
the ICMP header. This is fixed by adding the IP Header Length to
the casting into a icmphdr struct.
Signed-off-by: Ben Cartwright-Cox <ben@benjojo.co.uk>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This pci_error_handlers structure is never modified, like all the other
pci_error_handlers structures, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This pci_error_handlers structure is never modified, like all the other
pci_error_handlers structures, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Dell DW5580 is a 3G modem, this patch adds the device as a
mobile broadband adapter
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ndo_set_features fails __netdev_update_features() will return -1 but
this is wrong because it is expected to return 0 if no features were
changed (see netdev_update_features()), which will cause a netdev
notifier to be called without any actual changes. Fix this by returning
0 if ndo_set_features fails.
Fixes: 6cb6a27c45 ("net: Call netdev_features_change() from netdev_update_features()")
CC: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When __netdev_update_features() was updated to ensure some features are
disabled on new lower devices, an error was introduced for devices which
don't have the ndo_set_features() method set. Before we'll just set the
new features, but now we return an error and don't set them. Fix this by
returning the old behaviour and setting err to 0 when ndo_set_features
is not present.
Fixes: e7868a85e1 ("net/core: ensure features get disabled on new lower devs")
CC: Jarod Wilson <jarod@redhat.com>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Ido Schimmel <idosch@mellanox.com>
CC: Sander Eikelenboom <linux@eikelenboom.it>
CC: Andy Gospodarek <gospo@cumulusnetworks.com>
CC: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Dave Young <dyoung@redhat.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When NET_SWITCHDEV=n, switchdev_port_attr_set simply returns EOPNOTSUPP.
In this case we should not emit errors and warnings to the kernel log.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fixes: 0bc05d585d ("switchdev: allow caller to explicitly request
attr_set as deferred")
Fixes: 6ac311ae8b ("Adding switchdev ageing notification on port
bridged")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove rsstable array and its initialization from be_set_rss_hash_opts().
The array became unused after "e255787 be2net: Support for configurable
RSS hash key". The initial RSS table is now filled and stored for later
usage during Rx queue creation.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RX/TX interrupt for Network Control queue and Best Effort queue
is issued at the same time, the interrupt mask of Network Control
queue will be reset when the mask of Best Effort queue is set.
This patch fixes this problem.
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
On certain hardware after software reboot the chip may get stuck and fail
to reinitialize during reset. This can be fixed by ensuring that PHY is
reset too.
Old PHY resetting method required operational MDIO interface, therefore
the chip should have been already set up. In order to be able to function
during probe, it is changed to use PMT_CTRL register.
The problem could be observed on SMDK5410 board.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While recently going over ARM64's BPF code, I noticed that the icache
range we're flushing should start at header already and not at ctx.image.
Reason is that after b569c1c622 ("net: bpf: arm64: address randomize
and write protect JIT code"), we also want to make sure to flush the
random-sized trap in front of the start of the actual program (analogous
to x86). No operational differences from user side.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Zi Shen Lim <zlim.lnx@gmail.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
During review I noticed that the icache range we're flushing should
start at header already and not at ctx.image.
Reason is that after 55309dd3d4 ("net: bpf: arm: address randomize
and write protect JIT code"), we also want to make sure to flush the
random-sized trap in front of the start of the actual program (analogous
to x86). No operational differences from user side.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Nicolas Schichan <nschichan@freebox.fr>
Cc: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 338d4f49d6
("arm64: kernel: Add support for Privileged Access Never") includes sysreg.h
into futex.h and uaccess.h. But, the inline assembly used by asm/sysreg.h is
incompatible with llvm so it will cause BPF samples build failure for ARM64.
Since sysreg.h is useless for BPF samples, just exclude it from Makefile via
defining __ASM_SYSREG_H.
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF fp should point to the top of the BPF prog stack. The original
implementation made it point to the bottom incorrectly.
Move A64_SP to fp before reserve BPF prog stack space.
CC: Zi Shen Lim <zlim.lnx@gmail.com>
CC: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Reviewed-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the Vitesse VSC8601 PHY. Generic functions are
used for everything except interrupt handling.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 77a993942 "phy/at8031: enable at8031 to work on interrupt mode"
added interrupt support for the 8031 PHY but left out the other two
chips supported by this driver.
This patch sets the .ack_interrupt and .config_intr functions for the
8030 and 8035 drivers as well.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers like vxlan use the recently introduced
udp_tunnel_xmit_skb/udp_tunnel6_xmit_skb APIs. udp_tunnel6_xmit_skb
makes use of ip6tunnel_xmit, and ip6tunnel_xmit, after sending the
packet, updates the struct stats using the usual
u64_stats_update_begin/end calls on this_cpu_ptr(dev->tstats).
udp_tunnel_xmit_skb makes use of iptunnel_xmit, which doesn't touch
tstats, so drivers like vxlan, immediately after, call
iptunnel_xmit_stats, which does the same thing - calls
u64_stats_update_begin/end on this_cpu_ptr(dev->tstats).
While vxlan is probably fine (I don't know?), calling a similar function
from, say, an unbound workqueue, on a fully preemptable kernel causes
real issues:
[ 188.434537] BUG: using smp_processor_id() in preemptible [00000000] code: kworker/u8:0/6
[ 188.435579] caller is debug_smp_processor_id+0x17/0x20
[ 188.435583] CPU: 0 PID: 6 Comm: kworker/u8:0 Not tainted 4.2.6 #2
[ 188.435607] Call Trace:
[ 188.435611] [<ffffffff8234e936>] dump_stack+0x4f/0x7b
[ 188.435615] [<ffffffff81915f3d>] check_preemption_disabled+0x19d/0x1c0
[ 188.435619] [<ffffffff81915f77>] debug_smp_processor_id+0x17/0x20
The solution would be to protect the whole
this_cpu_ptr(dev->tstats)/u64_stats_update_begin/end blocks with
disabling preemption and then reenabling it.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently it's assumed that firmware exports only the class of sensors
supported by the driver. However with newer firmware or SCPI protocol
revision, support for newer classes of sensors can be present.
The driver fails to probe with the following warning if an unsupported
class of sensor is encountered in the firmware.
sysfs: cannot create duplicate filename
'/devices/platform/scpi/scpi:sensors/hwmon/hwmon0/'
------------[ cut here ]------------
WARNING: at fs/sysfs/dir.c:31
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/u12:0 Not tainted 4.3.0-rc7 #137
Hardware name: ARM Juno development board (r0) (DT)
Workqueue: deferwq deferred_probe_work_func
PC is at sysfs_warn_dup+0x54/0x78
LR is at sysfs_warn_dup+0x54/0x78
This patch fixes the above issue by skipping through the unsupported
class of SCPI sensors.
Fixes: 68acc77a2d ("hwmon: Support thermal zones registration for SCP temperature sensors")
Fixes: ea98b29a05 ("hwmon: Support sensors exported via ARM SCP interface")
Cc: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The newly added scpi thermal support is broken when the scpi driver
is built-in but the thermal driver is a loadable module:
drivers/built-in.o: In function `scpi_hwmon_probe':
(.text+0x444d70): undefined reference to `thermal_zone_of_sensor_unregister'
(.text+0x444d94): undefined reference to `thermal_zone_of_sensor_register'
drivers/built-in.o: In function `scpi_hwmon_remove':
(text+0x444e6c): undefined reference to `thermal_zone_of_sensor_unregister'
This uses the same Kconfig trick that we have in a couple of other
drivers already to ensure we can only select the driver in valid
configurations when either THERMAL_OF is disabled, or when with a
dependency on CONFIG_THERMAL that can force SCPI to be a loadable
module in the case I was hitting.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 68acc77a2d ("hwmon: Support thermal zones registration for SCP temperature sensors")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There is no known user, therefore remove the code.
Acked-by: Rob Van Der Heij <robvdheij@nl.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Passes mlock2-tests test case in 64 bit and compat mode.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove dead code, since this could only happen on a 31 bit machine
where the kernel wouldn't IPL.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
commit 1f6b83e5e4 ("s390: avoid z13 cache aliasing") checks for the
machine type to optimize address space randomization and zero page
allocation to avoid cache aliases.
This check might fail under a hypervisor with migration support.
z/VMs "Single System Image and Live Guest Relocation" facility will
"fake" the machine type of the oldest system in the group. For example
in a group of zEC12 and Z13 the guest appears to run on a zEC12
(architecture fencing within the relocation domain)
Remove the machine type detection and always use cache aliasing
rules that are known to work for all machines. These are the z13
aliasing rules.
Suggested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix the following "maybe used uninitialized" warnings by
initializing the variables to keep the compiler quiet.
There is no "used uninitialized" in this case.
CC [M] drivers/hwmon/applesmc.o
drivers/hwmon/applesmc.c: In function ‘applesmc_init_smcreg’:
drivers/hwmon/applesmc.c:595:43: warning: ‘right_light_sensor’
may be used uninitialized in this function [-Wmaybe-uninitialized]
s->num_light_sensors = left_light_sensor + right_light_sensor;
^
drivers/hwmon/applesmc.c:540:26: note: ‘right_light_sensor’ was
declared here
bool left_light_sensor, right_light_sensor;
^
drivers/hwmon/applesmc.c:595:43: warning: ‘left_light_sensor’ may
be used uninitialized in this function [-Wmaybe-uninitialized]
s->num_light_sensors = left_light_sensor + right_light_sensor;
^
drivers/hwmon/applesmc.c:540:7: note: ‘left_light_sensor’ was
declared here
bool left_light_sensor, right_light_sensor;
^
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since a0de56c81f ("hwmon: (ina2xx) convert driver to using regmap")
the driver requires REGMAP_I2C to build. Select it by default
in Kconfig.
Reported-by: Guo Chunrong <B40290@freescale.com>
Cc: Marc Titinger <mtitinger@baylibre.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Fixes: a0de56c81f ("hwmon: (ina2xx) convert driver to using regmap")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Neil Armstrong says:
====================
net: dsa: mv88e6060: cleanup and fix setup
This patchset introduces some fixes and a registers addressing cleanup for
the mv88e6060 DSA driver.
The first patch removes the poll_link as mv88e6xxx.
The 3 following patches fixes the setup in regards of the datasheet.
The 2 last patches introduces a clean header and replaces all magic values.
v2: cleanup InitReady patch, add missing Acked-by and fix header copyright notice
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To align with the mv88e6xxx code, use the register defines to
access all the register addresses and bit fields.
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To align with the mv88e6xxx code, add a similar header file
with all the register defines.
The file is based on the mv88e6xxx header for coherency.
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the mv88e6060 datasheet, the first mac byte must
be at position 9 instead of 8 since the bit 8 is used to select
if the mac address must differ for each port for Pause frames.
Use the correct shift and set the same mac address for all port.
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the mv88e6060 datasheet, the MaxFrameSize bit position
is 10 instead of 11 which is reserved.
Use the bit correctly to setup max frame size to 1536.
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the mv88e6060 datasheet, the InitReady bit position
is 11 and the polarity is inverted.
Use the bit correctly to detect the end of initialization.
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of mv88e6xxx remove the poll_link callback since the link
state change polling is now handled by the phylib.
Tested on a mv88e6060 B0 device with a TI DM816X SoC.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz says:
====================
Mellanox NIC driver update, Nov 12, 2015
Few small mlx5 and mlx4 fixes from the team... done over
net commit c5a3788 "Merge branch 'akpm' (patches from Andrew)"
Eran's patch needs to go to 4.2 and 4.3 stable kernels.
Tariq's patch need to go to 4.3 stable too.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The err variable wasn't set with the correct error value in some cases.
Fixes: 47605df953 ('mlx4: Modify proxy/tunnel QP mechanism [..]')
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When cleaning slave's counter resources, we hold a spinlock that
protects the slave's counters list. As part of the clean, we call
__mlx4_clear_if_stat which calls mlx4_alloc_cmd_mailbox which is a
sleepable function.
In order to fix this issue, hold the spinlock, and copy all counter
indices into a temporary array, and release the spinlock. Afterwards,
iterate over this array and free every counter. Repeat this scenario
until the original list is empty (a new counter might have been added
while releasing the counters from the temporary array).
Fixes: b72ca7e96a ("net/mlx4_core: Reset counters data when freed")
Reported-by: Moni Shoua <monis@mellanox.com>
Tested-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On xmit path we use skb_frag_dma_map() which is using dma_map_page(),
while upon completion we dma-unmap the skb fragments using
dma_unmap_single() rather than dma_unmap_page().
To fix this, we now save the dma map type on xmit path and use this
info to call the right dma unmap method upon TX completion.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert Uytterhoeven
Ondrej Zary
Neil Horman
Pavel Fedin
Bjørn Mork
Hannes Frederic Sowa
Dragos Tatulea
Yuval Mintz
Masaru Nagai
Ben Cartwright-Cox
Julia Lawall
Shrikrishna Khare
Daniele Palmas
Nikolay Aleksandrov
Ido Schimmel
Ivan Vecera
Daniel Borkmann
Yang Shi
Måns Rullgård
Jason A. Donenfeld
Sudeep Holla
Arnd Bergmann
Heiko Carstens
Martin Schwidefsky
Shuah Khan
Li Yang
David S. Miller
Neil Armstrong
Linus Torvalds
Noa Osherovich
Eran Ben Elisha
Achiad Shochat