The skcipher API dynamically instantiates the transformation object
on request that implements the requested algorithm optimally on the
given platform. This notion of optimality only matters for cases like
bulk network or disk encryption, where performance can be a bottleneck,
or in cases where the algorithm itself is not known at compile time.
In the mscc case, we are dealing with AES encryption of a single
block, and so neither concern applies, and we are better off using
the AES library interface, which is lightweight and safe for this
kind of use.
Note that the scatterlist API does not permit references to buffers
that are located on the stack, so the existing code is incorrect in
any case, but avoiding the skcipher and scatterlist APIs entirely is
the most straight-forward approach to fixing this.
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Fixes: 28c5107aa9 ("net: phy: mscc: macsec support")
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call phy_disable_interrupts() in phy_init_hw() to "have a defined init
state as we don't know in which state the PHY is if the PHY driver is
loaded. We shouldn't assume that it's the chip power-on defaults, BIOS
or boot loader could have changed this. Or in case of dual-boot
systems the other OS could leave the PHY in whatever state." as pointed
out by Heiner.
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We face an issue with rtl8211f, a pin is shared between INTB and PMEB,
and the PHY Register Accessible Interrupt is enabled by default, so
the INTB/PMEB pin is always active in polling mode case.
As Heiner pointed out "I was thinking about calling
phy_disable_interrupts() in phy_init_hw(), to have a defined init
state as we don't know in which state the PHY is if the PHY driver is
loaded. We shouldn't assume that it's the chip power-on defaults, BIOS
or boot loader could have changed this. Or in case of dual-boot
systems the other OS could leave the PHY in whatever state."
Make phy_disable_interrupts() non-static so that it could be used in
phy_init_hw() to have a defined init state.
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have been relying on link events and mac_config() when the manual
pause modes are changed. With recent developments, such as moving
the programming of link state to mac_link_up(), this no longer works.
To ensure that we update the MAC, we must generate a link-down followed
by a link-up event; we can do that by setting mac_link_dropped and
triggering a resolve.
Fixes: 91a208f218 ("net: phylink: propagate resolved link config via mac_link_up()")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a phylink's ethtool set_pauseparam support deadlock caused by phylib
interacting with phylink: we must not hold the state lock while calling
phylib functions that may call into phylink_phy_change().
Fixes: f904f15ea9 ("net: phylink: allow ethtool -A to change flow control advertisement")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7ae7ad2f11 ("net: phy: smsc: use phy_read_poll_timeout()
to simplify the code") will print a lot of logs as follows when Ethernet
cable is not connected:
[ 4.473105] SMSC LAN8710/LAN8720 2188000.ethernet-1:00: lan87xx_read_status failed: -110
When wait 640 ms for check ENERGYON bit, the timeout should not be
regarded as an actual error and an error message also should not be
printed. due to a hardware bug in LAN87XX device, it leads to unstable
detection of plugging in Ethernet cable when LAN87xx is in Energy Detect
Power-Down mode. the workaround for it involves, when the link is down,
and at each read_status() call:
- disable EDPD mode, forcing the PHY out of low-power mode
- waiting 640ms to see if we have any energy detected from the media
- re-enable entry to EDPD mode
This is presumably enough to allow the PHY to notice that a cable is
connected, and resume normal operations to negotiate with the partner.
The problem is that when no media is detected, the 640ms wait times
out and this commit was modified to prints an error message. it is an
inappropriate conversion by used phy_read_poll_timeout() to introduce
this bug. so fix this issue by use read_poll_timeout() to replace
phy_read_poll_timeout().
Fixes: 7ae7ad2f11 ("net: phy: smsc: use phy_read_poll_timeout() to simplify the code")
Reported-by: Kevin Groeneveld <kgroeneveld@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 02a6efcab6 ("net: phy: allow scanning busses with missing
phys") added a special condition to return -ENODEV in case -ENODEV or
-EIO was returned from the first read of the MII_PHYSID1 register.
In case the MDIO bus data line pull-up is not strong enough, the MDIO
bus controller will not flag this as a read error. This can happen when
a pluggable daughter card is not connected and weak internal pull-ups
are used (since that is the only option, otherwise the pins are
floating).
The second read of MII_PHYSID2 will be correctly flagged an error
though, but now we will return -EIO which will be treated as a hard
error, thus preventing MDIO bus scanning loops to continue succesfully.
Apply the same logic to both register reads, thus allowing the scanning
logic to proceed.
Fixes: 02a6efcab6 ("net: phy: allow scanning busses with missing phys")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
When the PHY's strap register is read to determine if lane swapping is
needed the phy_read_mmd returns the value back into the ret variable.
If the call to read the strap fails the failed value is returned. If
the call to read the strap is successful then ret is possibly set to a
non-zero positive number. Without reseting the ret value to 0 this will
cause the parse DT function to return a failure.
Fixes: c4566aec6e ("net: phy: dp83869: Update port-mirroring to read straps")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When converting the MSCC PHY driver to shared PHY packages, the Serdes
configuration in vsc8584_config_init was modified to use 'base_addr'
instead of 'base' as the port number. But 'base_addr' isn't equal to
'addr' for all PHYs inside the package, which leads to the Serdes still
being enabled on those ports. This patch fixes it.
Fixes: deb04e9c0f ("net: phy: mscc: use phy_package_shared")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_OF_MDIO is set to be a module the code block is not
compiled. Use the IS_ENABLED macro that checks for both built in as
well as module.
Fixes: 4f58e6dceb ("net: phy: Cleanup the Edge-Rate feature in Microsemi PHYs.")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_OF_MDIO is set to be a module the code block is not
compiled. Use the IS_ENABLED macro that checks for both built in as
well as module.
Fixes: cf41a51db8 ("of/phylib: Use device tree properties to initialize Marvell PHYs.")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_OF_MDIO is set to be a module the code block is not
compiled. Use the IS_ENABLED macro that checks for both built in as
well as module.
Fixes: 2a10154abc ("net: phy: dp83867: Add TI dp83867 phy")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_OF_MDIO is set to be a module the code block is not
compiled. Use the IS_ENABLED macro that checks for both built in as
well as module.
Fixes: 01db923e83 ("net: phy: dp83869: Add TI dp83869 phy")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The u64_stats mechanism uses sequence counters to protect against 64-bit
values tearing on 32-bit architectures. Updating u64_stats is thus a
sequence counter write side critical section where preemption must be
disabled.
For mdiobus_stats_acct(), disable preemption upon the u64_stats update.
It is called from process context through mdiobus_read() and
mdiobus_write().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bf7afb29d5 ("phy: improve safety of fixed-phy MII register
reading") protected the fixed PHY status with a sequence counter.
Two years later, commit d2b977939b ("net: phy: fixed-phy: remove
fixed_phy_update_state()") removed the sequence counter's write side
critical section -- neutralizing its read side retry loop.
Remove the unused seqcount.
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
- remove a now unnecessary usage of the KERNEL_DS for
sys_oabi_epoll_ctl()
- update my email address in a number of drivers
- decompressor EFI updates from Ard Biesheuvel
- module unwind section handling updates
- sparsemem Kconfig cleanups
- make act_mm macro respect THREAD_SIZE
-----BEGIN PGP SIGNATURE-----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=vMHE
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
- remove a now unnecessary usage of the KERNEL_DS for
sys_oabi_epoll_ctl()
- update my email address in a number of drivers
- decompressor EFI updates from Ard Biesheuvel
- module unwind section handling updates
- sparsemem Kconfig cleanups
- make act_mm macro respect THREAD_SIZE
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8980/1: Allow either FLATMEM or SPARSEMEM on the multiplatform build
ARM: 8979/1: Remove redundant ARCH_SPARSEMEM_DEFAULT setting
ARM: 8978/1: mm: make act_mm() respect THREAD_SIZE
ARM: decompressor: run decompressor in place if loaded via UEFI
ARM: decompressor: move GOT into .data for EFI enabled builds
ARM: decompressor: defer loading of the contents of the LC0 structure
ARM: decompressor: split off _edata and stack base into separate object
ARM: decompressor: move headroom variable out of LC0
ARM: 8976/1: module: allow arch overrides for .init section names
ARM: 8975/1: module: fix handling of unwind init sections
ARM: 8974/1: use SPARSMEM_STATIC when SPARSEMEM is enabled
ARM: 8971/1: replace the sole use of a symbol with its definition
ARM: 8969/1: decompressor: simplify libfdt builds
Update rmk's email address in various drivers
ARM: compat: remove KERNEL_DS usage in sys_oabi_epoll_ctl()
Don't export __bcm_phy_enable_rdb_access() and
__bcm_phy_enable_legacy_access() functions. They aren't used outside this
module and it was forgotten to provide a prototype for these functions.
Just make them static for now.
Fixes: 11ecf8c55b ("net: phy: broadcom: add cable test support")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to call phy_restore_page() even if phy_select_page() fails.
Otherwise we are holding the phy_lock_mdio_bus() lock. This requirement
is documented at the start of the phy_select_page() function.
Fixes: a618e86da9 ("net : phy: marvell: Speedup TDR data retrieval by only changing page once")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHYs using the vsc8574_probe fail to be initialized and their
config_init return -EIO leading to errors like:
"could not attach PHY: -5".
This is because when the conversion of the MSCC PHY driver to use the
shared PHY package helpers was done, the base address retrieval and the
base PHY read and write helpers in the driver were modified. In
particular, the base address retrieval logic was moved from the
config_init to the probe. But the vsc8574_probe was forgotten. This
patch fixes it.
Fixes: deb04e9c0f ("net: phy: mscc: use phy_package_shared")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Atheros 100Base-T PHYs. The only difference seems to be
the ability to test 2 pairs instead of 4 and the lack of 1000Base-T
specific register.
Only the ATH9331 was tested with this patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When performing a TDR measurement for a short distance, the pulse
width should be low, to help differentiate between the outgoing pulse
and any reflection. For longer distances, the pulse should be wider,
to help with attenuation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Getting the TDR data requires a large number of MDIO bus
transactions. The number can however be reduced if the page is only
changed once. Add the needed locking to allow this, and make use of
unlocked read/write methods where needed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the user to configure where on the cable the TDR data should be
retrieved, in terms of first and last sample, and the step between
samples. Also add the ability to ask for TDR data for just one pair.
If this configuration is not provided, it defaults to 1-150m at 1m
intervals for all pairs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v3:
Move the TDR configuration into a structure
Add a range check on step
Use NL_SET_ERR_MSG_ATTR() when appropriate
Move TDR configuration into a nest
Document attributes in the request
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell PHYs can measure the amplitude of the returned signal for
a given distance. Implement this option of the cable test
infrastructure. When reporting the step, convert the distance into cm.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
Step based on the measurement resolution, and convert this to cm.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the generic parts of the code used to trigger a cable test and
return raw TDR data. Any PHY driver which support this must implement
the new driver op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2
Update nxp-tja11xx for API change.
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses a read polling mechanism to check the status of the MDIO
bus, to know if it is ready to accept next commands. This polling
mechanism uses usleep_delay() under the hood between reads which is fine
as long as high resolution timers are enabled. Otherwise the delays will
end up to be much longer than expected.
This patch fixes this by using udelay() under the hood when
CONFIG_HIGH_RES_TIMERS isn't enabled. This increases CPU usage.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC MIIM MDIO driver uses a waiting logic to wait for the MDIO bus
to be ready to accept next commands. It does so by polling the BUSY
status bit which indicates the MDIO bus has completed all pending
operations. This can take time, and the controller supports writing the
next command as soon as there are no pending commands (which happens
while the MDIO bus is busy completing its current command).
This patch implements this improved logic by adding an helper to poll
the PENDING status bit, and by adjusting where we should wait for the
bus to not be busy or to not be pending.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
readl_poll_timeout already returns -ETIMEDOUT if the condition isn't
satisfied, there's no need to check again the condition after calling
it. Remove the redundant timeout check.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC MIIM MDIO driver uses delays to read poll a status register. I
made multiple tests on a Ocelot PCS120 platform which led me to reduce
those delays. The delay in between which the polling function is allowed
to sleep is reduced from 100us to 50us which in almost all cases is a
good value to succeed at the first retry. The overall delay is also
lowered as the prior value was really way to high, 10000us is large
enough.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a recurring pattern throughout some of the PHY code converting
a devad and regnum to our packed clause 45 representation. Rather than
having this scattered around the code, let's put a common translation
function in mdio.h, and provide some register accessors.
Convert the phylib core, phylink, bcm87xx and cortina to use these.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
At the very end of the MACsec block initialization in the MSCC PHY
driver, the MACsec "protocol mode" is set. This setting should be set
based on the PHY id within the package, as the bank used to access the
register used depends on this. This was not done correctly, and only the
first bank was used leading to the two upper PHYs being unstable when
using the VSC8584. This patch fixes it.
Fixes: 1bbe0ecc2a ("net: phy: mscc: macsec initialization")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ever since its first commit 0ca7111a38 ("phy: add AT803x driver") the
PHY ID mask was set to 0xffffffef. It is unclear to me why this mask was
chosen in the first place. Both the AR8031/AR8033 and the AR8035
datasheets mention it is always the given value:
- for AR8031/AR8033 its 0x004d/0xd074
- for AR8035 its 0x004d/0xd072
Unfortunately, I don't have a datasheet for the AR8030. Therefore, we
leave its PHY ID mask untouched. For the PHYs mentioned before use the
handy PHY_ID_MATCH_EXACT() macro.
I've tried to contact the author of the initial commit, but received no
answer so far.
Cc: Matus Ujhelyi <ujhelyi.m@gmail.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the op-mode for the device is not set in the device tree then set
the strapped op-mode and store it for later configuration.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device tree may not have the property set for port mirroring
because the hardware may have it strapped. If the property is not in the
DT then check the straps and set the port mirroring bit appropriately.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements reading of the Signal Quality Index for better
cable/link troubleshooting.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function was introduced to allow for different handling of
link up and link down events particularly with regard to the
netif_carrier. The third argument do_carrier allowed the flag to
be left unchanged.
Since then the phylink has introduced an implementation that
completely ignores the third parameter since it never wants to
change the flag and the phylib always sets the third parameter
to true so the flag is always changed.
Therefore the third argument (i.e. do_carrier) is no longer
necessary and can be removed. This also means that the phylib
phy_link_down() function no longer needs its second argument.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The compilation warning below reveals that the errors returned from
the sfp_bus_add_upstream() call are not propagated to the callers.
Fix it by returning "ret".
14:37:51 drivers/net/phy/phy_device.c: In function 'phy_sfp_probe':
14:37:51 drivers/net/phy/phy_device.c:1236:6: warning: variable 'ret'
set but not used [-Wunused-but-set-variable]
14:37:51 1236 | int ret;
14:37:51 | ^~~
Fixes: 298e54fa81 ("net: phy: add core phylib sfp support")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes checkpatch happy for tabs
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the bpf verifier trace check into the new switch statement in
HEAD.
Resolve the overlapping changes in hinic, where bug fixes overlap
the addition of VF support.
Signed-off-by: David S. Miller <davem@davemloft.net>
A typical 100Base-T1 link should be always connected. If the link is in
a shot or open state, it is a failure. In most cases, we won't be able
to automatically handle this issue, but we need to log it or notify user
(if possible).
With this patch, the cable will be tested on "ip l s dev .. up" attempt
and send ethnl notification to the user space.
This patch was tested with TJA1102 PHY and "ethtool --monitor" command.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM54811 PHY shares many similarities with the already supported BCM54810
PHY but additionally requires some semi-unique configuration.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio-moxart doesn't use regulators in the driver code. We can remove
the regulator include.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the correct bit when checking for PHY_BRCM_DIS_TXCRXC_NOENRGY on the
BCM54810 PHY.
Fixes: 0ececcfc92 ("net: phy: broadcom: Allow BCM54810 to use bcm54xx_adjust_rxrefclk()")
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_restart_aneg() enables aneg in the PHY. That's not what we want
if phydev->autoneg is disabled. In this case still update EEE
advertisement register, but don't enable aneg and don't trigger an
aneg restart.
Fixes: f75abeb833 ("net: phy: restart phy autonegotiation after EEE advertisment change")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AR8031/AR8033 and the AR8035 support cable diagnostics. Adding
driver support is straightforward, so lets add it.
The PHY just do one pair at a time, so we have to start the test four
times. The cable_test_get_status() can block and therefore we can just
busy poll the test completion and continue with the next pair until we
are done.
The time delta counter seems to run at 125MHz which just gives us a
resolution of about 82.4cm per tick.
100m cable, A/B/C/D open:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair: Pair A, result: Open Circuit
Pair: Pair A, fault length: 107.94m
Pair: Pair B, result: Open Circuit
Pair: Pair B, fault length: 104.64m
Pair: Pair C, result: Open Circuit
Pair: Pair C, fault length: 105.47m
Pair: Pair D, result: Open Circuit
Pair: Pair D, fault length: 107.94m
1m cable, A/B connected, C shorted, D open:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair: Pair A, result: OK
Pair: Pair B, result: OK
Pair: Pair C, result: Short within Pair
Pair: Pair C, fault length: 0.82m
Pair: Pair D, result: Open Circuit
Pair: Pair D, fault length: 0.82m
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the generic cable tester functions from bcm-phy-lib to add cable
tester support.
100m cable, A/B/C/D open:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair: Pair A, result: Open Circuit
Pair: Pair B, result: Open Circuit
Pair: Pair C, result: Open Circuit
Pair: Pair D, result: Open Circuit
Pair: Pair A, fault length: 106.60m
Pair: Pair B, fault length: 103.32m
Pair: Pair C, fault length: 104.96m
Pair: Pair D, fault length: 106.60m
1m cable, A/B connected, pair C shorted, D open:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair: Pair A, result: OK
Pair: Pair B, result: OK
Pair: Pair C, result: Short within Pair
Pair: Pair D, result: Open Circuit
Pair: Pair C, fault length: 0.82m
Pair: Pair D, fault length: 1.64m
1m cable, A/B connected, pair C shorted with D:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair: Pair A, result: OK
Pair: Pair B, result: OK
Pair: Pair C, result: Short to another pair
Pair: Pair D, result: Short to another pair
Pair: Pair C, fault length: 1.64m
Pair: Pair D, fault length: 1.64m
The granularity of the length measurement seems to be 82cm.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most modern broadcom PHYs support ECD (enhanced cable diagnostics). Add
support for it in the bcm-phy-lib so they can easily be used in the PHY
driver.
There are two access methods for ECD: legacy by expansion registers and
via the new RDB registers which are exclusive. Provide functions in two
variants where the PHY driver can choose from. To keep things simple for
now, we just switch the register access to expansion registers in the
RDB variant for now. On the flipside, we have to keep a bus lock to
prevent any other non-legacy access on the PHY.
The results of the intra-pair tests are inconclusive (at least for the
BCM54140). Most of the times half the length is reported but sometimes
the length is correct.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ard Biesheuvel
Jisheng Zhang
Russell King
Dejin Zheng
Florian Fainelli
Masahiro Yamada
Dan Murphy
Antoine Tenart
Ahmed S. Darwish
Linus Torvalds
Michael Walle
Dan Carpenter
Oleksij Rempel
Andrew Lunn
David S. Miller
Doug Berger
Leon Romanovsky
Kevin Lo
Bartosz Golaszewski
Heiner Kallweit