We need to use a different firmware for C0 versions of killer Qu NICs.
Add structures for them and handle them in the if block that detects
C0 revisions.
Additionally, instead of having an inclusive check for QnJ devices,
make the selection exclusive, so that switching to QnJ is the
exception, not the default. This prevents us from having to add all
the non-QnJ cards to an exclusion list. To do so, only go into the
QnJ block if the device has an RF ID type HR and HW revision QnJ.
Cc: stable@vger.kernel.org # 5.2
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190821171732.2266-1-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If 'fq' qdisc is used and a program has requested timestamps,
skb->tstamp needs to be cleared, else fq will treat these as
'transmit time'.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since the chained quirks via chained_before flag is applied before the
depth check, it may lead to the endless recursive calls, when the
chain were set up incorrectly. Fix it by moving the depth check at
the beginning of the loop.
Fixes: 1f57825077 ("ALSA: hda - Add chained_before flag to the fixup entry")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
lib/devres.c, which implements devm_ioremap_resource(), is only built
when CONFIG_HAS_IOMEM is set/enabled, so MTD_HYPERBUS should depend
on HAS_IOMEM. Fixes a build error and a Kconfig warning (as seen on
UML builds):
WARNING: unmet direct dependencies detected for MTD_COMPLEX_MAPPINGS
Depends on [n]: MTD [=m] && HAS_IOMEM [=n]
Selected by [m]:
- MTD_HYPERBUS [=m] && MTD [=m]
ERROR: "devm_ioremap_resource" [drivers/mtd/hyperbus/hyperbus-core.ko] undefined!
Fixes: dcc7d3446a ("mtd: Add support for HyperBus memory devices")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-mtd@lists.infradead.org
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
A similar workaround for the suspend/resume problem is needed for yet
another ASUS machines, P6X models. Like the previous fix, the BIOS
doesn't provide the standard DMI_SYS_* entry, so again DMI_BOARD_*
entries are used instead.
Reported-and-tested-by: SteveM <swm@swm1.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
nfp: flower: fix bugs in merge tunnel encap code
John says:
There are few bugs in the merge encap code that have come to light with
recent driver changes. Effectively, flow bind callbacks were being
registered twice when using internal ports (new 'busy' code triggers
this). There was also an issue with neighbour notifier messages being
ignored for internal ports.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent code changes to NFP allowed the offload of neighbour entries to FW
when the next hop device was an internal port. This allows for offload of
tunnel encap when the end-point IP address is applied to such a port.
Unfortunately, the neighbour event handler still rejects events that are
not associated with a repr dev and so the firmware neighbour table may get
out of sync for internal ports.
Fix this by allowing internal port neighbour events to be correctly
processed.
Fixes: 45756dfeda ("nfp: flower: allow tunnels to output to internal port")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Internal port TC offload is implemented through user-space applications
(such as OvS) by adding filters at egress via TC clsact qdiscs. Indirect
block offload support in the NFP driver accepts both ingress qdisc binds
and egress binds if the device is an internal port. However, clsact sends
bind notification for both ingress and egress block binds which can lead
to the driver registering multiple callbacks and receiving multiple
notifications of new filters.
Fix this by rejecting ingress block bind callbacks when the port is
internal and only adding filter callbacks for egress binds.
Fixes: 4d12ba4278 ("nfp: flower: allow offloading of matches on 'internal' ports")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hayes Wang says:
====================
r8152: fix side effect
v3:
Update the commit message for patch #1.
v2:
Replace patch #2 with "r8152: remove calling netif_napi_del".
v1:
The commit 0ee1f47349 ("r8152: napi hangup fix after disconnect")
add a check to avoid using napi_disable after netif_napi_del. However,
the commit ffa9fec30c ("r8152: set RTL8152_UNPLUG only for real
disconnection") let the check useless.
Therefore, I revert commit 0ee1f47349 ("r8152: napi hangup fix
after disconnect") first, and add another patch to fix it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary use of netif_napi_del. This also avoids to call
napi_disable() after netif_napi_del().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 0ee1f47349.
The commit 0ee1f47349 ("r8152: napi hangup fix after
disconnect") adds a check about RTL8152_UNPLUG to determine
if calling napi_disable() is invalid in rtl8152_close(),
when rtl8152_disconnect() is called. This avoids to use
napi_disable() after calling netif_napi_del().
Howver, commit ffa9fec30c ("r8152: set RTL8152_UNPLUG
only for real disconnection") causes that RTL8152_UNPLUG
is not always set when calling rtl8152_disconnect().
Therefore, I have to revert commit 0ee1f47349 ("r8152:
napi hangup fix after disconnect"), first. And submit
another patch to fix it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP associates tx timestamp requests with a byte in the bytestream.
If merging skbs in tcp_mtu_probe, migrate the tstamp request.
Similar to MSG_EOR, do not allow moving a timestamp from any segment
in the probe but the last. This to avoid merging multiple timestamps.
Tested with the packetdrill script at
https://github.com/wdebruij/packetdrill/commits/mtu_probe-1
Link: http://patchwork.ozlabs.org/patch/1143278/#2232897
Fixes: 4ed2d765df ("net-timestamp: TCP timestamping")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Action sample doesn't properly handle psample_group pointer in overwrite
case. Following issues need to be fixed:
- In tcf_sample_init() function RCU_INIT_POINTER() is used to set
s->psample_group, even though we neither setting the pointer to NULL, nor
preventing concurrent readers from accessing the pointer in some way.
Use rcu_swap_protected() instead to safely reset the pointer.
- Old value of s->psample_group is not released or deallocated in any way,
which results resource leak. Use psample_group_put() on non-NULL value
obtained with rcu_swap_protected().
- The function psample_group_put() that released reference to struct
psample_group pointed by rcu-pointer s->psample_group doesn't respect rcu
grace period when deallocating it. Extend struct psample_group with rcu
head and use kfree_rcu when freeing it.
Fixes: 5c5670fae4 ("net/sched: Introduce sample tc action")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the ibmvnic driver will not schedule device resets
if the device is being removed, but does not check the device
state before the reset is actually processed. This leads to a race
where a reset is scheduled with a valid device state but is
processed after the driver has been removed, resulting in an oops.
Fix this by checking the device state before processing a queued
reset event.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pfn_valid can be wrong when parsing a invalid pfn whose phys address
exceeds BITS_PER_LONG as the MSB will be trimed when shifted.
The issue originally arise from bellowing call stack, which corresponding to
an access of the /proc/kpageflags from userspace with a invalid pfn parameter
and leads to kernel panic.
[46886.723249] c7 [<c031ff98>] (stable_page_flags) from [<c03203f8>]
[46886.723264] c7 [<c0320368>] (kpageflags_read) from [<c0312030>]
[46886.723280] c7 [<c0311fb0>] (proc_reg_read) from [<c02a6e6c>]
[46886.723290] c7 [<c02a6e24>] (__vfs_read) from [<c02a7018>]
[46886.723301] c7 [<c02a6f74>] (vfs_read) from [<c02a778c>]
[46886.723315] c7 [<c02a770c>] (SyS_pread64) from [<c0108620>]
(ret_fast_syscall+0x0/0x28)
Signed-off-by: Zhaoyang Huang <zhaoyang.huang@unisoc.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Currently, various virtual memory areas of Linux RISC-V are organized
in increasing order of their virtual addresses is as follows:
1. User space area (This is lowest area and starts at 0x0)
2. FIXMAP area
3. VMALLOC area
4. Kernel area (This is highest area and starts at PAGE_OFFSET)
The maximum size of user space aread is represented by TASK_SIZE.
On RV32 systems, TASK_SIZE is defined as VMALLOC_START which causes the
user space area to overlap the FIXMAP area. This allows user space apps
to potentially corrupt the FIXMAP area and kernel OF APIs will crash
whenever they access corrupted FDT in the FIXMAP area.
On RV64 systems, TASK_SIZE is set to fixed 256GB and no other areas
happen to overlap so we don't see any FIXMAP area corruptions.
This patch fixes FIXMAP area corruption on RV32 systems by setting
TASK_SIZE to FIXADDR_START. We also move FIXADDR_TOP, FIXADDR_SIZE,
and FIXADDR_START defines to asm/pgtable.h so that we can avoid cyclic
header includes.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Only the first fragment in a datagram contains the L4 headers. When the
Open vSwitch module parses a packet, it always sets the IP protocol
field in the key, but can only set the L4 fields on the first fragment.
The original behavior would not clear the L4 portion of the key, so
garbage values would be sent in the key for "later" fragments. This
patch clears the L4 fields in that circumstance to prevent sending those
garbage values as part of the upcall.
Signed-off-by: Justin Pettit <jpettit@ovn.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IP fragments are reassembled before being sent to conntrack, the
key from the last fragment is used. Unless there are reordering
issues, the last fragment received will not contain the L4 ports, so the
key for the reassembled datagram won't contain them. This patch updates
the key once we have a reassembled datagram.
The handle_fragments() function works on L3 headers so we pull the L3/L4
flow key update code from key_extract into a new function
'key_extract_l3l4'. Then we add a another new function
ovs_flow_key_update_l3l4() and export it so that it is accessible by
handle_fragments() for conntrack packet reassembly.
Co-authored-by: Justin Pettit <jpettit@ovn.org>
Signed-off-by: Greg Rose <gvrose8192@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that 'TCQ_F_CPUSTATS' bit can be cleared, depending on the value of
'TCQ_F_NOLOCK' bit in the parent qdisc, we need to be sure that per-cpu
counters are present when 'reset()' is called for pfifo_fast qdiscs.
Otherwise, the following script:
# tc q a dev lo handle 1: root htb default 100
# tc c a dev lo parent 1: classid 1:100 htb \
> rate 95Mbit ceil 100Mbit burst 64k
[...]
# tc f a dev lo parent 1: protocol arp basic classid 1:100
[...]
# tc q a dev lo parent 1:100 handle 100: pfifo_fast
[...]
# tc q d dev lo root
can generate the following splat:
Unable to handle kernel paging request at virtual address dfff2c01bd148000
Mem abort info:
ESR = 0x96000004
Exception class = DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
[dfff2c01bd148000] address between user and kernel address ranges
Internal error: Oops: 96000004 [#1] SMP
[...]
pstate: 80000005 (Nzcv daif -PAN -UAO)
pc : pfifo_fast_reset+0x280/0x4d8
lr : pfifo_fast_reset+0x21c/0x4d8
sp : ffff800d09676fa0
x29: ffff800d09676fa0 x28: ffff200012ee22e4
x27: dfff200000000000 x26: 0000000000000000
x25: ffff800ca0799958 x24: ffff1001940f332b
x23: 0000000000000007 x22: ffff200012ee1ab8
x21: 0000600de8a40000 x20: 0000000000000000
x19: ffff800ca0799900 x18: 0000000000000000
x17: 0000000000000002 x16: 0000000000000000
x15: 0000000000000000 x14: 0000000000000000
x13: 0000000000000000 x12: ffff1001b922e6e2
x11: 1ffff001b922e6e1 x10: 0000000000000000
x9 : 1ffff001b922e6e1 x8 : dfff200000000000
x7 : 0000000000000000 x6 : 0000000000000000
x5 : 1fffe400025dc45c x4 : 1fffe400025dc357
x3 : 00000c01bd148000 x2 : 0000600de8a40000
x1 : 0000000000000007 x0 : 0000600de8a40004
Call trace:
pfifo_fast_reset+0x280/0x4d8
qdisc_reset+0x6c/0x370
htb_reset+0x150/0x3b8 [sch_htb]
qdisc_reset+0x6c/0x370
dev_deactivate_queue.constprop.5+0xe0/0x1a8
dev_deactivate_many+0xd8/0x908
dev_deactivate+0xe4/0x190
qdisc_graft+0x88c/0xbd0
tc_get_qdisc+0x418/0x8a8
rtnetlink_rcv_msg+0x3a8/0xa78
netlink_rcv_skb+0x18c/0x328
rtnetlink_rcv+0x28/0x38
netlink_unicast+0x3c4/0x538
netlink_sendmsg+0x538/0x9a0
sock_sendmsg+0xac/0xf8
___sys_sendmsg+0x53c/0x658
__sys_sendmsg+0xc8/0x140
__arm64_sys_sendmsg+0x74/0xa8
el0_svc_handler+0x164/0x468
el0_svc+0x10/0x14
Code: 910012a0 92400801 d343fc03 11000c21 (38fb6863)
Fix this by testing the value of 'TCQ_F_CPUSTATS' bit in 'qdisc->flags',
before dereferencing 'qdisc->cpu_qstats'.
Changes since v1:
- coding style improvements, thanks to Stefano Brivio
Fixes: 8a53e616de ("net: sched: when clearing NOLOCK, clear TCQ_F_CPUSTATS, too")
CC: Paolo Abeni <pabeni@redhat.com>
Reported-by: Li Shuang <shuali@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yash Shah says:
====================
macb: Update ethernet compatible string for SiFive FU540
This patch series renames the compatible property to a more appropriate
string. The patchset is based on Linux-5.3-rc6 and tested on SiFive
Unleashed board
Change history:
Since v1:
- Dropped PATCH3 because it's already merged
- Change the reference url in the patch descriptions to point to a
'lore.kernel.org' link instead of 'lkml.org'
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the compatibility string for SiFive FU540-C000 as per the new
string updated in the binding doc.
Reference:
https://lore.kernel.org/netdev/CAJ2_jOFEVZQat0Yprg4hem4jRrqkB72FKSeQj4p8P5KA-+rgww@mail.gmail.com/
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Paul Walmsley <paul.walmsley@sifive.com>
Tested-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per the discussion with Nicolas Ferre[0], rename the compatible property
to a more appropriate and specific string.
[0] https://lore.kernel.org/netdev/CAJ2_jOFEVZQat0Yprg4hem4jRrqkB72FKSeQj4p8P5KA-+rgww@mail.gmail.com/
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Paul Walmsley <paul.walmsley@sifive.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scom driver currently fails out of operations if certain system
errors are flagged in the status register; system checkstop, special
attention, or recoverable error. These errors won't impact the ability
of the scom engine to perform operations, so the driver should continue
under these conditions.
Also, don't do a PIB reset for these conditions, since it won't help.
Fixes: 6b293258cd ("fsi: scom: Major overhaul")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20190827041249.13381-1-jk@ozlabs.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Francois reported that VMware balloon gets stuck after a balloon reset,
when the VMCI doorbell is removed. A similar error can occur when the
balloon driver is removed with the following splat:
[ 1088.622000] INFO: task modprobe:3565 blocked for more than 120 seconds.
[ 1088.622035] Tainted: G W 5.2.0 #4
[ 1088.622087] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1088.622205] modprobe D 0 3565 1450 0x00000000
[ 1088.622210] Call Trace:
[ 1088.622246] __schedule+0x2a8/0x690
[ 1088.622248] schedule+0x2d/0x90
[ 1088.622250] schedule_timeout+0x1d3/0x2f0
[ 1088.622252] wait_for_completion+0xba/0x140
[ 1088.622320] ? wake_up_q+0x80/0x80
[ 1088.622370] vmci_resource_remove+0xb9/0xc0 [vmw_vmci]
[ 1088.622373] vmci_doorbell_destroy+0x9e/0xd0 [vmw_vmci]
[ 1088.622379] vmballoon_vmci_cleanup+0x6e/0xf0 [vmw_balloon]
[ 1088.622381] vmballoon_exit+0x18/0xcc8 [vmw_balloon]
[ 1088.622394] __x64_sys_delete_module+0x146/0x280
[ 1088.622408] do_syscall_64+0x5a/0x130
[ 1088.622410] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 1088.622415] RIP: 0033:0x7f54f62791b7
[ 1088.622421] Code: Bad RIP value.
[ 1088.622421] RSP: 002b:00007fff2a949008 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0
[ 1088.622426] RAX: ffffffffffffffda RBX: 000055dff8b55d00 RCX: 00007f54f62791b7
[ 1088.622426] RDX: 0000000000000000 RSI: 0000000000000800 RDI: 000055dff8b55d68
[ 1088.622427] RBP: 000055dff8b55d00 R08: 00007fff2a947fb1 R09: 0000000000000000
[ 1088.622427] R10: 00007f54f62f5cc0 R11: 0000000000000206 R12: 000055dff8b55d68
[ 1088.622428] R13: 0000000000000001 R14: 000055dff8b55d68 R15: 00007fff2a94a3f0
The cause for the bug is that when the "delayed" doorbell is invoked, it
takes a reference on the doorbell entry and schedules work that is
supposed to run the appropriate code and drop the doorbell entry
reference. The code ignores the fact that if the work is already queued,
it will not be scheduled to run one more time. As a result one of the
references would not be dropped. When the code waits for the reference
to get to zero, during balloon reset or module removal, it gets stuck.
Fix it. Drop the reference if schedule_work() indicates that the work is
already queued.
Note that this bug got more apparent (or apparent at all) due to
commit ce664331b2 ("vmw_balloon: VMCI_DOORBELL_SET does not check status").
Fixes: 83e2ec765b ("VMCI: doorbell implementation.")
Reported-by: Francois Rigault <rigault.francois@gmail.com>
Cc: Jorgen Hansen <jhansen@vmware.com>
Cc: Adit Ranadive <aditr@vmware.com>
Cc: Alexios Zavras <alexios.zavras@intel.com>
Cc: Vishnu DASA <vdasa@vmware.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nadav Amit <namit@vmware.com>
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Link: https://lore.kernel.org/r/20190820202638.49003-1-namit@vmware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of a disconnect an ongoing flush() has to be made fail.
Nevertheless we cannot be sure that any pending URB has already
finished, so although they will never succeed, they still must
not be touched.
The clean solution for this is to check for WDM_IN_USE
and WDM_DISCONNECTED in flush(). There is no point in ever
clearing WDM_IN_USE, as no further writes make sense.
The issue is as old as the driver.
Fixes: afba937e54 ("USB: CDC WDM driver")
Reported-by: syzbot+d232cca6ec42c2edb3fc@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190827103436.21143-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's spelled "renesas", not "renensas".
Due to this typo, RZ/G1M and RZ/G1N were not covered by the check.
Fixes: 2dc240a330 ("usb: host: xhci: rcar: retire use of xhci_plat_type_is()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20190827125112.12192-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Falcon microcontroller that runs the XUSB firmware and which is
responsible for exposing the XHCI interface can address only 40 bits of
memory. Typically that's not a problem because Tegra devices don't have
enough system memory to exceed those 40 bits.
However, if the ARM SMMU is enable on Tegra186 and later, the addresses
passed to the XUSB controller can be anywhere in the 48-bit IOV address
space of the ARM SMMU. Since the DMA/IOMMU API starts allocating from
the top of the IOVA space, the Falcon microcontroller is not able to
load the firmware successfully.
Fix this by setting the DMA mask to 40 bits, which will force the DMA
API to map the buffer for the firmware to an IOVA that is addressable by
the Falcon.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/1566989697-13049-1-git-send-email-nkristam@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Auto-delink requires writing special registers to ums-realtek devices.
Unconditionally enable auto-delink may break newer devices.
So only enable auto-delink by default for the original three IDs,
0x0138, 0x0158 and 0x0159.
Realtek is working on a patch to properly support auto-delink for other
IDs.
BugLink: https://bugs.launchpad.net/bugs/1838886
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190827173450.13572-2-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The option named "auto_delink_en" is a bit misleading, as setting it to
false doesn't really disable auto-delink but let auto-delink be firmware
controlled.
Update the description to reflect the real usage of this parameter.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190827173450.13572-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an issue that the following error is
possible to happen when ohci hardware causes an interruption
and the system is shutting down at the same time.
[ 34.851754] usb 2-1: USB disconnect, device number 2
[ 35.166658] irq 156: nobody cared (try booting with the "irqpoll" option)
[ 35.173445] CPU: 0 PID: 22 Comm: kworker/0:1 Not tainted 5.3.0-rc5 #85
[ 35.179964] Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT)
[ 35.187886] Workqueue: usb_hub_wq hub_event
[ 35.192063] Call trace:
[ 35.194509] dump_backtrace+0x0/0x150
[ 35.198165] show_stack+0x14/0x20
[ 35.201475] dump_stack+0xa0/0xc4
[ 35.204785] __report_bad_irq+0x34/0xe8
[ 35.208614] note_interrupt+0x2cc/0x318
[ 35.212446] handle_irq_event_percpu+0x5c/0x88
[ 35.216883] handle_irq_event+0x48/0x78
[ 35.220712] handle_fasteoi_irq+0xb4/0x188
[ 35.224802] generic_handle_irq+0x24/0x38
[ 35.228804] __handle_domain_irq+0x5c/0xb0
[ 35.232893] gic_handle_irq+0x58/0xa8
[ 35.236548] el1_irq+0xb8/0x180
[ 35.239681] __do_softirq+0x94/0x23c
[ 35.243253] irq_exit+0xd0/0xd8
[ 35.246387] __handle_domain_irq+0x60/0xb0
[ 35.250475] gic_handle_irq+0x58/0xa8
[ 35.254130] el1_irq+0xb8/0x180
[ 35.257268] kernfs_find_ns+0x5c/0x120
[ 35.261010] kernfs_find_and_get_ns+0x3c/0x60
[ 35.265361] sysfs_unmerge_group+0x20/0x68
[ 35.269454] dpm_sysfs_remove+0x2c/0x68
[ 35.273284] device_del+0x80/0x370
[ 35.276683] hid_destroy_device+0x28/0x60
[ 35.280686] usbhid_disconnect+0x4c/0x80
[ 35.284602] usb_unbind_interface+0x6c/0x268
[ 35.288867] device_release_driver_internal+0xe4/0x1b0
[ 35.293998] device_release_driver+0x14/0x20
[ 35.298261] bus_remove_device+0x110/0x128
[ 35.302350] device_del+0x148/0x370
[ 35.305832] usb_disable_device+0x8c/0x1d0
[ 35.309921] usb_disconnect+0xc8/0x2d0
[ 35.313663] hub_event+0x6e0/0x1128
[ 35.317146] process_one_work+0x1e0/0x320
[ 35.321148] worker_thread+0x40/0x450
[ 35.324805] kthread+0x124/0x128
[ 35.328027] ret_from_fork+0x10/0x18
[ 35.331594] handlers:
[ 35.333862] [<0000000079300c1d>] usb_hcd_irq
[ 35.338126] [<0000000079300c1d>] usb_hcd_irq
[ 35.342389] Disabling IRQ #156
ohci_shutdown() disables all the interrupt and rh_state is set to
OHCI_RH_HALTED. In other hand, ohci_irq() is possible to enable
OHCI_INTR_SF and OHCI_INTR_MIE on ohci_irq(). Note that OHCI_INTR_SF
is possible to be set by start_ed_unlink() which is called:
ohci_irq()
-> process_done_list()
-> takeback_td()
-> start_ed_unlink()
So, ohci_irq() has the following condition, the issue happens by
&ohci->regs->intrenable = OHCI_INTR_MIE | OHCI_INTR_SF and
ohci->rh_state = OHCI_RH_HALTED:
/* interrupt for some other device? */
if (ints == 0 || unlikely(ohci->rh_state == OHCI_RH_HALTED))
return IRQ_NOTMINE;
To fix the issue, ohci_shutdown() holds the spin lock while disabling
the interruption and changing the rh_state flag to prevent reenable
the OHCI_INTR_MIE unexpectedly. Note that io_watchdog_func() also
calls the ohci_shutdown() and it already held the spin lock, so that
the patch makes a new function as _ohci_shutdown().
This patch is inspired by a Renesas R-Car Gen3 BSP patch
from Tho Vu.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1566877910-6020-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using managed device resources in usb_hcd_pci_probe() allows devm usage for
resource subranges, such as the mmio resource for the platform device
created to control host/device mode mux, which is a xhci extended
capability, and sits inside the xhci mmio region.
If managed device resources are not used then "parent" resource
is released before subrange at driver removal as .remove callback is
called before the devres list of resources for this device is walked
and released.
This has been observed with the xhci extended capability driver causing a
use-after-free which is now fixed.
An additional nice benefit is that error handling on driver initialisation
is simplified much.
Signed-off-by: Carsten Schmid <carsten_schmid@mentor.com>
Tested-by: Carsten Schmid <carsten_schmid@mentor.com>
Reviewed-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Fixes: fa31b3cb2a ("xhci: Add Intel extended cap / otg phy mux handling")
Cc: <stable@vger.kernel.org> # v4.19+
Link: https://lore.kernel.org/r/1566569488679.31808@mentor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There appears to be a typo in the comparison of pdo_max_voltage[i]
with the previous value, currently it is checking against the
array pdo_min_voltage rather than pdo_max_voltage. I believe this
is a typo. Fix this.
Addresses-Coverity: ("Copy-paste error")
Fixes: 5007e1b5db ("typec: tcpm: Validate source and sink caps")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190822135212.10195-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To address the requirements of embargoed hardware issues, like Meltdown,
Spectre, L1TF etc. it is necessary to define and document a process for
handling embargoed hardware security issues.
Following the discussion at the maintainer summit 2018 in Edinburgh
(https://lwn.net/Articles/769417/) the volunteered people have worked
out a process and a Memorandum of Understanding. The latter addresses
the fact that the Linux kernel community cannot sign NDAs for various
reasons.
The initial contact point for hardware security issues is different from
the regular kernel security contact to provide a known and neutral
interface for hardware vendors and researchers. The initial primary
contact team is proposed to be staffed by Linux Foundation Fellows, who
are not associated to a vendor or a distribution and are well connected
in the industry as a whole.
The process is designed with the experience of the past incidents in
mind and tries to address the remaining gaps, so future (hopefully rare)
incidents can be handled more efficiently. It won't remove the fact,
that most of this has to be done behind closed doors, but it is set up
to avoid big bureaucratic hurdles for individual developers.
The process is solely for handling hardware security issues and cannot
be used for regular kernel (software only) security bugs.
This memo can help with hardware companies who, and I quote, "[my
manager] doesn't want to bet his job on the list keeping things secret."
This despite numerous leaks directly from that company over the years,
and none ever so far from the kernel security team. Cognitive
dissidence seems to be a requirement to be a good manager.
To accelerate the adoption of this process, we introduce the concept of
ambassadors in participating companies. The ambassadors are there to
guide people to comply with the process, but are not automatically
involved in the disclosure of a particular incident.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Laura Abbott <labbott@redhat.com>
Acked-by: Ben Hutchings <ben@decadent.org.uk>
Reviewed-by: Tyler Hicks <tyhicks@canonical.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Link: https://lore.kernel.org/r/20190815212505.GC12041@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lkdtm/bugs.c:94:2: error: format '%d' expects argument of type 'int', but argument 2 has type 'long unsigned int' [-Werror=format=]
pr_info("Calling function with %d frame size to depth %d ...\n",
^
THREAD_SIZE is defined as a unsigned long, cast CONFIG_FRAME_WARN to
unsigned long as well.
Fixes: 24cccab42c ("lkdtm/bugs: Adjust recursion test to avoid elision")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20190827173619.170065-1-rrangel@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A single fix for the altera-ps-spi driver that fixes the behavior when
the driver receives -EPROBE_DEFER when trying to obtain a GPIO desc.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQS/ea/a56fFi9QbQeJ+E8eWOj6VqQUCXVnwggAKCRB+E8eWOj6V
qZlLAQDZA+zyKkY/69BtF2oMG1ilZ0XAg5imZiPDkCUleEQjAgEApE0snS7YKc/f
cRrIFy6jTAsw1S553kYoB384prnnTwg=
=npyY
-----END PGP SIGNATURE-----
Merge tag 'fpga-fixes-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mdf/linux-fpga into char-misc-linus
Moritz writes:
FPGA Manager fixes for 5.3
A single fix for the altera-ps-spi driver that fixes the behavior when
the driver receives -EPROBE_DEFER when trying to obtain a GPIO desc.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
* tag 'fpga-fixes-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mdf/linux-fpga:
fpga: altera-ps-spi: Fix getting of optional confd gpio
Thomas and I seem to have become the "unofficial" maintainers for these
files and questions about SPDX things. So let's make it official.
Reported-by: "Darrick J. Wong" <darrick.wong@oracle.com>
Grumpily-acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Darrick J. Wong <darrick.wong@oracle.com>
Link: https://lore.kernel.org/r/20190827195310.GA30618@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix GICv2 emulation bug (KVM)
- Fix deadlock in virtual GIC interrupt injection code (KVM)
- Fix kprobes blacklist init failure due to broken kallsyms lookup
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl1mW/0ACgkQt6xw3ITB
YzQWEQgAnG+20c1uzPqIEME3o0bCXsci0I1w4yPYPH/NVrfmJdAjfway/cLZlMCh
JYKBTc392kfYXgzAvMqvjNe+9O/qg9MnMxV7Afjfk9e0k+41Kcw/7U39/B6q4yOg
zIz4YW6SdbbbUfY9VgR8SjsZ3HwJoP8YVNEv3W259funtFHkKDO35h1iG1f57GWL
UELjEnag9dmCH35ykt7+SC4woBGjOQnic2XLSS7VZuU/26TfnUyo2HCdDcLcViCZ
DHDQgaHAscb+tgJjeNtNEeRu+GPBG9LOhPw4EpBjGHeoJla7z74GOJPMEt4Ufoqd
qG9TPfOFAFM30/PAdlWF3SjfzqK3PA==
=WYzY
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Hot on the heels of our last set of fixes are a few more for -rc7.
Two of them are fixing issues with our virtual interrupt controller
implementation in KVM/arm, while the other is a longstanding but
straightforward kallsyms fix which was been acked by Masami and
resolves an initialisation failure in kprobes observed on arm64.
- Fix GICv2 emulation bug (KVM)
- Fix deadlock in virtual GIC interrupt injection code (KVM)
- Fix kprobes blacklist init failure due to broken kallsyms lookup"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
KVM: arm/arm64: vgic-v2: Handle SGI bits in GICD_I{S,C}PENDR0 as WI
KVM: arm/arm64: vgic: Fix potential deadlock when ap_list is long
kallsyms: Don't let kallsyms_lookup_size_offset() fail on retrieving the first symbol
Yi reported[1] that after commit a3619190d6 ("libnvdimm/pfn: stop
padding pmem namespaces to section alignment"), it was no longer
possible to create a device dax namespace with a 1G alignment. The
reason was that the pmem region was not itself 1G-aligned. The code
happily skips past the first 512M, but fails to account for a now
misaligned end offset (since space was allocated starting at that
misaligned address, and extending for size GBs). Reintroduce
end_trunc, so that the code correctly handles the misaligned end
address. This results in the same behavior as before the introduction
of the offending commit.
[1] https://lists.01.org/pipermail/linux-nvdimm/2019-July/022813.html
Fixes: a3619190d6 ("libnvdimm/pfn: stop padding pmem namespaces ...")
Reported-and-tested-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Link: https://lore.kernel.org/r/x49ftll8f39.fsf@segfault.boston.devel.redhat.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The de-init routine should be doing the following in order:-
1. Unregister the drm device
2. Shut down the crtcs - failing to do this might cause a connector leakage
See the 'commit 109c4d18e5 ("drm/arm/malidp: Ensure that the crtcs are
shutdown before removing any encoder/connector")'
3. Disable the interrupts
4. Unbind the components
5. Free up DRM mode_config info
Changes from v1:-
1. Re-ordered the header files inclusion
2. Rebased on top of the latest drm-misc-fixes
Signed-off-by:. Ayan Kumar Halder <Ayan.Halder@arm.com>
Reviewed-by: Mihail Atanassov <mihail.atanassov@arm.com>
Reviewed-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Link: https://patchwork.freedesktop.org/patch/327606/
One of the very few warnings I have in the current build comes from
arch/x86/boot/edd.c, where I get the following with a gcc9 build:
arch/x86/boot/edd.c: In function ‘query_edd’:
arch/x86/boot/edd.c:148:11: warning: taking address of packed member of ‘struct boot_params’ may result in an unaligned pointer value [-Waddress-of-packed-member]
148 | mbrptr = boot_params.edd_mbr_sig_buffer;
| ^~~~~~~~~~~
This warning triggers because we throw away all the CFLAGS and then make
a new set for REALMODE_CFLAGS, so the -Wno-address-of-packed-member we
added in the following commit is not present:
6f303d6053 ("gcc-9: silence 'address-of-packed-member' warning")
The simplest solution for now is to adjust the warning for this version
of CFLAGS as well, but it would definitely make sense to examine whether
REALMODE_CFLAGS could be derived from CFLAGS, so that it picks up changes
in the compiler flags environment automatically.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Walking the address list of an inet6_dev requires
appropriate locking. Since the called function
siw_listen_address() may sleep, we have to use
rtnl_lock() instead of read_lock_bh().
Also introduces sanity checks if we got a device
from in_dev_get() or in6_dev_get().
Reported-by: Bart Van Assche <bvanassche@acm.org>
Fixes: 6c52fdc244 ("rdma/siw: connection management")
Signed-off-by: Bernard Metzler <bmt@zurich.ibm.com>
Link: https://lore.kernel.org/r/20190828130355.22830-1-bmt@zurich.ibm.com
Signed-off-by: Doug Ledford <dledford@redhat.com>
The register number needs to be translated for chips with more than 8
ports. This patch fixes a bug causing all chips with more than 8 GPIO pins
to not work correctly.
Fixes: 0f25fda840 ("gpio: pca953x: Zap ad-hoc reg_direction cache")
Cc: Cc: <stable@vger.kernel.org>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Luca Coelho
Florian Westphal
Takashi Iwai
Randy Dunlap
Laurent Pinchart
David S. Miller
John Hurley
Hayes Wang
Davide Caratti
Willem de Bruijn
Vlad Buslov
Thomas Falcon
zhaoyang
Anup Patel
Justin Pettit
Greg Rose
Eric Dumazet
Yash Shah
Eddie James
Nadav Amit
Oliver Neukum
Geert Uytterhoeven
Nagarjuna Kristam
Kai-Heng Feng
Yoshihiro Shimoda
Schmid, Carsten
Colin Ian King
Thomas Gleixner
Raul E Rangel
Tomas Winkler
Alexander Shishkin
Ding Xiang
Greg Kroah-Hartman
Linus Torvalds
Jeff Moyer
Ayan Kumar Halder
Bernard Metzler
David Jander