Fix this build error when CONFIG_PM is not set:
ound/pci/hda/hda_intel.c: In function 'azx_bus_reset':
sound/pci/hda/hda_intel.c:1270: error: implicit declaration of function 'snd_pcm_suspend_all'
sound/pci/hda/hda_intel.c:1271: error: implicit declaration of function 'snd_hda_suspend'
sound/pci/hda/hda_intel.c:1272: error: implicit declaration of function 'snd_hda_resume'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable all three capture channels, including the missing nid 7 which is
the only one capable of capturing DMIC input
Enable Headphone amp for the HP jack. This causes a volume boost for
headphones, but does not cause any noticeable effect for light loads
like other amps, so there is no need to make it configurable.
Add Input Mix capture mux setting to capture the output of the playback
input mux (that is, what goes out the speakers except for PCM)
Hack another coef register because the stereo DMIC for some reason
produces a nonstandard sum/difference signal. I found a bit to make it
just use the sum signal for both channels, which makes it behave like a
standard mono microphone. The stereo is useless anyway (they're 1cm apart).
Tested working: Three capture channels, mic in, line in, DMIC.
Tested not working: CD. Not sure why, might be unconnected in the actual
hardware or a CD drive issue.
Also looked at SPDIF. It appears to work (emitter lights up inside the
HP out jack) but I lack a proper miniTOSLINK cable to test it.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the limitation of PAGE_SIZE to be 4k by defining the own
page size and macros for 4k. 8kb page size could be natively supported,
but it's disabled right now for simplicity.
Also, clean up using upper_32_bits() macro.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The device seems supporting only U8, S16, S24_3LE, S32. Other linear
formats result in bad outputs.
Also, added the support for 32bit float format, which wasn't listed
in the original code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
PCM names for surround streams should be also fixed as well as the mixer
element names. Also, a bit clean up for PCM name setup.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We usually pick up "Surround" mixer for the rear output, and "Side"
for the extra surround. Fix the channel mapping to follow it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The prepare callback can be called multiple times, thus it needs to
release and acquire the resource again by itself at the second or later
call.
Simply add pcm_release_resources() at the beginning of each prepare
callback in ctatc.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SNDRV_PCM_SUBCLASS_GENERIC_MIX is mostly for h/w multi-stream playback
devices, but ca0106 and emu10k1x don't support it (unlike emu10k1).
We shouldn't set that flag to avoid confusion.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although the vmaster controls are created, they aren't registered thus
they don't appear in the real world. Added the missing snd_ctl_add()
calls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
Short story: this laptop has 5.1 built-in speakers which you *really*
want to use (the not-so-"sub" woofer is what makes the audio above
average for a laptop), so 6-channel support is important (plus a decent
asound.conf to upmix stereo). It also has the 3 typical jacks that ought
to have a selectable mode. And it's based on ALC889, which sucks.
Rationale/explanations:
The const_channel_count stuff was added because, for a laptop like this,
you always have 6 channels available (internal speakers) but still need
to set the mode for the 3 external jacks. Therefore, the device always
needs to be in 6-channel mode but there still needs to be a mixer
control for the jack mode. You could use line/mic-in at the same time as
the 6 internal speakers, for example. You might be tempted to make it
even smarter by dynamically switching the max channel count when
headphones are plugged in (therefore muting the internal speakers and
reducing the physical channel count to the jack channel mode), but as a
user I consider this to be harmful because I want the audio to blow up
to 6 channels / upmixed as soon as I unplug the headphones, and having
opened the device while in 2-channel mode would prevent this from
working (and always making 6-channel mode available doesn't do any harm).
The hardware needs EAPD turned on and the DACs routed to the internal
speaker pins, so the patch adds those verbs.
The ALC889 CLFE and subsequent (side/aux, here unused) DACs do NOT work
by default, at least here. I wasted much time trying to talk to
Realtek/pshou about this, but they just kept sending me useless updates
to patch_realtek.c that did nothing relevant. In the end I gave up and
brute forced the issue by trying to flip every bit in the proprietary
coefficient registers, and eventually found the two magic registers that
need to be cleared to enable all DACs. I have only heard Acer users
complain, but that might be because ALC889 is pretty new and using 5.1
(and noticing the missing center/lfe channels) might not be that common.
If this is a generalized issue with all ALC889 systems then those verbs
should probably be moved to a common verb array.
The internal mic is untested and probably doesn't work.
These settings will probably work for other Acer Gemstone laptops with
the same 5.1 speaker config. When identified, those should be added to
the PCI subsystem ID list.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The reset of a BUS controller during operations is somehow risky and
shouldn't be done inevitably for devices that have apparently no such
codec-communication problems.
This patch adds the check of the hardware and limits the bus-reset
capability.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some machines machine cause a severe CORB/RIRB stall in certain
weird conditions, such as PA access at the start up together with
fglrx driver. This seems unable to be recovered without the controller
reset.
This patch allows the bus controller reset at critical errors so
that the communication gets recovered again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, LG R510 is only able to produce sound on headphones, the
internal speakers are not working.
The user tested and confirmed that with model=Dell headphones,
internal speakers and the microphone are working flawlessly.
Tested-by: Serdar Soytetir <tulliana@gmail.com>
Signed-off-by: Ozan Çağlayan <ozan@pardus.org.tr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
this is a patch against current snapshot that adds:
6 channels support for the MB5 model
Signed-off-by: Kacper Szczesniak <kacper@qwe.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix issues for 3 generations of HP workstations.
The modest modifications do the following:
1. Change the second MIC from device 3 to device 1
2. Init the "boost" values to "0" by default
From: John Brown <john.brown3@hp.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch changes Line In as Out Switch and Mic In as Out Switch to
enums for consistency, and causes all mic and line in ports to be probed
and controls to be added appropriately.
Signed-off-by: Nickolas Lloyd <ultrageek.lloyd@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ICH6_GCTL_RESET was wrongly set to another bit by the commit
b21fadb9c1. This caused a problem when
the codec needs really a reset (e.g. recovering from the communication
error at probe).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of mangling the CONFIG_* variables in the makefiles over and
over, set a few helper variables in Kconfig.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The period_elapsed() call should be called when position moves.
The idea was taken from ALSA bug#4455.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Appearently, the used mask in the .pointer callback is invalid. It should
be in period_bytes range. The period_bytes is pow(2), so simple bitwise
operation is used.
Idea was taken from ALSA bug#4455.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added some missing register bits definitions to reduce magic numbers.
Also renamed some to follow the names on the datasheet.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the single_cmd mode, the hardware cannot store the multiple replies
like on RIRB, thus each verb has to sync and wait for the response no
matter whether the return value is needed or not. Otherwise it may
result in a wrong return value from the previous verb.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A docking mic control is shown by default. The Compaq Presario
CQ60 laptop has no docking connector, so designate it as a
CXT5051_HP model.
This makes the phantom mixer slider disappear.
Signed-off-by: Tony Vroon <tony@linx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Add missing check of pin vref 50 and others in Realtek codecs
ALSA: hda - Add 5stack-no-fp model for STAC927x
ALSA: hda - Add forced codec-slots for ASUS W5Fm
This patch adds a debug mode to make the codec communication
synchronous. Define SND_HDA_SUPPORT_SYNC_WRITE in hda_codec.c,
and the call of snd_hda_codec_write*() will become synchronous,
i.e. wait for the reply from the codec at each time issuing a verb.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the single_cmd mode, the current driver code doesn't do any update
for RIRB just for any safety reason. But, actually the RIRB and
single_cmd mode don't conflict. Unsolicited events can be delivered
even while using the single_cmd mode.
This patch allows the handling of unsolicited events with single_cmd
mode, just always checking RIRB independent from single_cmd flag.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current code doesn't handle the multiple gameports properly,
and uses unnecessary global static variables to store the data.
This patch changes the probe / remove routines to use the driver
data assigned to the dedicated pci device, and adds the support of
multiple devices.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A code clean up, coding style fixes.
The firmware loading routine is split to an own function to improve
the readability.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a codec communication error occurs, the CORB/RIRB counters should
be reset first before re-issuing the verb. Simply call azx_free_cmd_io()
and azx_init_cmd_io() to achieve that.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for the Asus Xonar Essence ST and its daughterboard.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Xonar HDAV1.3 has a digital input jack, so enable the corresponding
device.
This is not related to the HDMI stuff, which stays unsupported.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add another PCI ID for a second revision of the Xonar DX.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a PCM stream is closed, flush the corresponding DMA channel.
Otherwise, the DMA controller would continue to output the last sample
which would result in a DC offset on the output.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some Realtek codecs like ALC861 seem to support only VREF50 while the
current driver assumes it's only VREF80. Check other VREF bits to set
the correct value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent fix for the headphone volume control on IDT/STAC codecs
resulted in the removal of invalid "Side" volume eventually. But,
if the front panel doesn't exist, this setup could be regarded as a
sort of regression, as reported in kernel bug #13250.
Now as a workaround, a new model 5stack-no-fp is added so that the user
without the front panel can choose this one explicitly.
Reference: bko#13250
http://bugzilla.kernel.org/show_bug.cgi?id=13250
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS W5Fm needs the fixed codec-slots to probe to override the BIOS
problem like W5F.
Tested-by: Alp Kılıç <kilic.alp@gmail.com>
Signed-off-by: Ozan Çağlayan <ozan@pardus.org.tr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA sound/core/control.c:232: Control name 'Sigmatel Surround Phase
Inversion Playback Switch' truncated to 'Sigmatel Surround Phase
Inversion Playback ' bootup message by omitting weird Sigmatel prefix
in this case; also fix up the related ca0106 mixer control removal
part by using identical naming there.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ctxfi driver requires explicitly the 4k page size, and gives a
build error on architectures with non-4k pages.
As a workaround, just add the kconfig dependency on X86, which is
the only architecture ever tested.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The digital beep tone is calculated in two different ways depending
on the codec chip. The standard one is using a divider, and another
one is a linear tone for IDT/STAC codecs. Currently, only the
latter type is used for all codecs, which resulted in a wrong tone
pitch.
This patch adds the calculation of the standard HD-audio type.
Also clean-up the fields in hda_beep struct.
Reference: bko#13162
http://bugzilla.kernel.org/show_bug.cgi?id=13162
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add proper prefix to each kernel message in hda_intel.c.
Also, avoid the unneeded prefix when CONFIG_SND_VERBOSE_PRINTK is used
together with snd_print*().
Reference: bko#13207
http://bugzilla.kernel.org/show_bug.cgi?id=13207
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for MacBook 3,1 sound by adding a model new
"mb31" with the appropriate init verbs, mixers and channel modes to
the ALC883 configuration. patch_alc882() and patch_alc883() are
modified to handle the MacBook 3,1 sound-chip (Realtek ALC889A)
correctly.
Signed-off-by: Torben Schulz <public@letorbi.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCI entries of Creative with HD-audio class can be the devices
with emu20k1/emu20k2 chips. These are supported better by snd-ctxfi
driver. With that driver, the device will mutate from HD-audio to
its native class.
This patch adds a simple ifdef to avoid the conflict of device probe
between snd-hda-intel and snd-ctxfi drivers. 1102:0009 seems still
OK to be added as it has no emu20kx chip, and is a pure HD-audio
device.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Split the name string in hda_codec struct to vendor_name and chip_name
strings to be stored directly from the preset name.
Since mostly only the chip name is referred in many patch_*.c, this
results in the reduction of many codes in the end.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds a mixer control for the STAC92XX boards to control the
DC bias of mic ports, allowing recording from both powered and
non-powered sources. It replaces the "Mic Output Switch" with "Mic Jack
Mode" to switch between Mic, Line In, and Line Out.
Signed-off-by: Nickolas Lloyd <ultrageek.lloyd@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the codec SSID for MacBook Pro 5,1 as compatible as MP51.
However, the headphone auto-muting function doesn't work. So,
this is just a tentative solution.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With a postfix increment these variables are incremented beyond
CMDIF_TIMEOUT / MAX_WRITE_RETRY.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The model=acer for ALC883/889 doesn't work well for the recent Acer
Aspire laptops. Since model=auto works better nowadays, it's safer
to use the default fallback instead of the Acer specific one.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the hdsp driver is built in kernel, the corresponding firmware
files have to be built into the kernel as well (otherwise the boot
will hang up for fairly long time), but there is no way to control
it in Kconfig yet, unfortunately. Instead, show a comment for user
just to make sure.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow the use of the FIRMWARE_IN_KERNEL option with hdsp cards and
in-kernel driver.
Also corrected a typo in the comment.
Signed-off-by: Raphael Doursenaud <rdoursenaud@free.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add specific configuration for Samsung NC10 mini notebook. Internal
mic/speakers will be correctly muted when plugging in external ones.
Mixer controls are added for speakers, headphones and PC beep.
"Boost" is added for the microphones.
Signed-off-by: Chris Pockelé <chris.pockele.f1@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the missing descriptions and the model names for Realtek codecs
to the documentation and the config table.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Most of unsol handlers defined in patch_realtek.c can be classified to
two types, mute via amp of pins and mute via ctl bits of pins.
Thus there are a big room to generalize each implementation.
This patch creates two generic functions, alc_automute_amp() and
alc_automute_pin(). The latter is actually changed from the previous
alc_sku_automute(). Each caller needs to initialize hp_pins and
speaker_pins properly at own init_hook.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The speaker auto-muting per HP plugging for ALC262 HIPPO and compatible
devices is slightly buggy as the "Master" or "Front" mixer control can
still toggle the speaker output even if the headphone is plugged.
This patch fixes the issue, and clean up the hippo-related codes
together with fixes of some inconsistent mixer names.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
VIA VT1708S and VT1702 codecs can have two SPDIF outputs. One of them
should have been handled as the extra digital out, but it's not
properly accessed.
This patch fixes the handling of the secondary SPDIF on these codecs
with the slave dig-out as found in patch_sigmatel.c. This makes the
use of such a device easier (for normal users).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BIOS on Mac Mini Core2 Duo sets both INPUT and OUTPUT pinctl bits to
the line-in jack, and it confuses the driver as if it's a valid input.
This patch adds the check of OUTPUT bit so that the driver fixes the
invalid pin setup.
Tested-by: Tino Keitel <tino.keitel@gmx.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added a new flag, own_routing, to allow spec drivers to create own
routing controls. Also, the basic get/put calls are changed to be
external for later use by maya44 driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The set_rate might return error but the current code doesn't check it.
This patch adds a proper error check.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With 5 bits and 1.5 dB per step, the DXS volume range is only 48 dB.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added SNDRV_PCM_INFO_BATCH flag to PCM info field of some drivers that
really don't give the precise pointer value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commmit dfed0ef9b3 was reverted
accidentally by the merge of auto-detection fix patch.
Fixed again now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable auto-muting in model=auto only for devices with HP and speakers.
For devices with HP and line-outs, don't enable the auto-muting.
Also, add a debug print to show the auto-mute feature.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the realtek auto-probing mode, the initialization of amp with
some magic COEF or EAPD verbs is applied only when the codec SSID
has valid values to satisfy the realtek's definition.
However, many devices don't provide in that way, thus the device
doesn't work as is.
This patch allows the same initialization code even if the SSID
doesn't pass the bit test. Also, alc_subsystem_id() is changed
just to check and define the type, so that it's called in the
parser, instead of the initializer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixed the compile warning below by initializatin iomidi variable properly.
sound/pci/cmipci.c: In function ‘snd_cmipci_probe’:
sound/pci/cmipci.c:3017: warning: ‘iomidi’ may be used uninitialized in this function
Signed-off-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Cc: linux-pci <linux-pci@atrey.karlin.mff.cuni.cz>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Sachin P Sant <sachinp@linux.vnet.ibm.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current ad1884a-mobile model has a problem that the speaker output
doesn't work sometimes after boot or power-saving on some HP laptops.
It seems that the verbs accessing to the non-functional widgets cause
this problem.
This patch simplifies the init verbs for mobile model not to touch
unnecessary setups so that it avoids the speaker-mute problem.
Reference: Novell bnc#495668
https://bugzilla.novell.com/show_bug.cgi?id=495668
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Appearently, a big delay ~300ms is required before hw is settled and ready
to transfer samples on some hardware variants. Also, return back
"clocking to 48000Hz" message when something fails.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The current error-recovery scheme for the codec communication errors
doesn't work always well. Especially falling back to the
single-command mode causes the fatal problem on many systems.
In this patch, the problematic verb is re-issued again after the error
(even with polling mode) instead of the single-cmd mode. The
single-cmd mode will be used only when specified via the command
option explicitly, mainly just for testing.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cache quries for PCM and STREAM parameters as well as ampcap and
pincap sharing the hash table. This will reduce the superfluous
access of the same codec verbs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Support ASUS F81Se F5Q P80 U20A U80 U50 UX50 for ALC269
- Support ASUS F70SL UX20 X58LE F50Z N80Vc N81Te N505Tp Vx3V N5051A
for ALC663
- Support DELL ZM1 for ALC272
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Don't unmute unneeded amps for input mixers of ALC662 & co.
It caused possible recording noises.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the missing definition of max channels for CA0110, which resulted
in an error at opening PCM devices.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
(Re)set function_id only from the value on FG nodes.
The current code overrides the value with the last widget.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the headphone can have no unique DAC, the current code doesn't
check the HP-detection although it should. Put the hp-detection check
before the DAC check to fix this bug.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check the length to copy via strlen() beforehand to avoid the stack
corruption, or use strlcpy() to be safe in HD-audio codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the support for Creative SB X-Fi boards with UAA (HD-audio) mode.
In the HD-audio mode, no multiple streams are supported by just it
behaves like a normal HD-audio device.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Subject says it all. Briefly, use hp_only for another Dell Inspiron 8600.
Reference: Ubuntu #41015 (https://launchpad.net/bugs/41015)
Signed-off-by: Daniel T Chen <seven.steps@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While cleaning up quirks, I noticed that there is a duplicated quirk for
the SSID 0x103c0934. Looking back through the bug reports, I've concluded
that there is only one necessary quirk (hp_mute_led), so this patch
removes the conflicting one.
Reference: Ubuntu #44066 (https://launchpad.net/bugs/44066)
Signed-off-by: Daniel T Chen <seven.steps@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit fa00e046b4
added a new bitfield not adjacent to other
bitfields in the same struct. Moved the new one.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the key value generation for get/set amp verbs. The upper bits of
the parameter have to be combined with the verb value to be unique for
each direction/index of amp access.
This fixes the resume problem on some hardwares like Macbook after
the channel mode is changed.
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* topic/memdup_user:
ALSA: sound/pci: use memdup_user()
ALSA: sound/usb: use memdup_user()
ALSA: sound/isa: use memdup_user()
ALSA: sound/core: use memdup_user()
* 'master' of git://git.alsa-project.org/alsa-kernel:
[ALSA] intel8x0: add one retry to the ac97_clock measurement routine
[ALSA] intel8x0: fix wrong conditions in ac97_clock measure routine
[ALSA] intel8x0: do not use zero value from PICB register
[ALSA] intel8x0: an attempt to make ac97_clock measurement more reliable
[ALSA] pcm-midlevel: Add more strict buffer position checks based on jiffies
[ALSA] hda_intel: fix unexpected ring buffer positions
Added the models for quirk bitmask 1734:110x and 1734:113x of
Fujitsu laptops.
This will fix the model detection for Amilo Xa3540.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It seems that on some hardware platforms, the first measurement is wrong.
This patch adds second measurement to this case.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Don't call snd_jack_report at release of sigmatel and conexnat codecs
which results in Oops at unloading the module.
The Oops is triggered by the power-up sequence during the free due to
the pincfg restoration. Since the power-up sequence is involved with
the unsol handling, the jack reporting may be issued during that.
The Oops occurs with this jack reporting because the jack instances
have been already released but the codec doesn't do the proper
book-keeping.
This patch adds the book-keeping of jack instances to avoid the access
to bogus pointers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>