The CONFIG register has two 3-bit fields for conversion time
settings of Bus-voltage and Shunt-voltage, respectively. The
conversion settings, along with averaging mode, allow users
to optimize available timing requirement.
This patch adds an 'update_interval' sysfs node through the
hwmon_chip_info of hwmon core. It reflects a total hardware
conversion time:
samples * channels * (Bus + Shunt conversion times)
Though INA3221 supports different conversion time setups for
Bus and Shunt voltages, this patch only adds the support of
a unified setting for both conversion times, by dividing the
conversion time into two equal values.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
[groeck: .rst related formatting changes in documentation]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reading back the CONFIG register increases an extra I2C
transaction. This's not necessary and could be replaced
with a local variable caching the register settings.
So this patch replaces two readback regmap_read() calls
with a tmp variable.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Now that all files were converted to ReST format, rename them
and add an index.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The help text needs to spell out how the driver runs on a BMC, as it
previously seemed to indicate it ran on a POWER processor.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The error sysfs attribute returns the stored error state of the OCC and
doesn't depend on the OCC poll response. Therefore, split the error
attribute into it's own function to avoid failing out of the function if
the poll response fails.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The OCC driver limits the rate of sending poll commands to the OCC. If a
user reads a hwmon entry after a poll response resulted in an error and
is rate-limited, the error is invisible to the user. Fix this by storing
the last error and returning that in the rate-limited case.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The CONFIG register has a 3-bit averaging mode field for users
to setup the number of samples that are collected and averaged
together. This is very useful to filter noise from sensor data.
This patch adds a 'samples' sysfs node using hwmon_chip_samples
of hwmon core, and updates wait time calculation by taking this
samples value into account.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Intersil ISL68137 is a digital output 7-phase configurable PWM
controller with an AVSBus interface.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Signed-off-by: Robert Lippert <rlippert@google.com>
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch makes it possible to pass custom struct attribute_group array
via the pmbus_driver_info struct so that those can be added to the
attribute groups passed to hwmon_device_register_with_groups().
This makes it possible to register custom sysfs attributes by PMBUS
drivers similar to how you can do this with most other busses/classes.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the new samples attributes to the hwmon core.
Cc: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Cc: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Manufacturer specific SAMPLES_FOR_AVG register allows setting the number
of samples used in computing the average values (PMBUS_VIRT_READ_*_AVG).
The number we write is an exponent of base 2 of the number of samples so
for example writing 3 will result in 8 samples average.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Those virtual registers can be used to export manufacturer specific
functionality for controlling the number of samples for average values
reported by the device.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Replace S_<PERMS> with octal values.
The conversion was done automatically with coccinelle. The semantic patches
and the scripts used to generate this commit log are available at
https://github.com/groeck/coccinelle-patches/.
This patch does not introduce functional changes. It was verified by
compiling the old and new files and comparing text and data sizes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the pmbus driver for the Infineon ir38064 voltage regulator.
VOUT_MODE is not supported by the device. The driver fakes linear16
mode with exponent value -8.
The device supports VOUT_PEAK, IOUT_PEAK, and TEMPERATURE_PEAK, however
this driver does not enable them.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Printing the error code for a failure provides a head-start for
debugging, since it's often sufficient to pinpoint the origin of the
failure. We already do this for some probe-failure messages, so let's
make the rest of them consistent.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This adds RPM support to the pwm-fan driver in order to use with
fancontrol/pwmconfig. This feature is intended for fans with a tachometer
output signal, which generate a defined number of pulses per revolution.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
[groeck: Drop unused 'devattr' variable]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These drivers are for a BMC inside PowerPC servers. The BMC runs on
ARM hardware, so only propose the drivers on this architecture, unless
build-testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Eddie James <eajames@linux.ibm.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Instead of duplicating the common code into the 2 (binary) drivers,
move the common code to a separate module. This is cleaner.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Eddie James <eajames@linux.ibm.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Tested-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: 2219cd81a6 ("hwmon/vt1211: Add probing of alternate config index port")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: b72656dbc4 ("hwmon: (w83627hf) Stop using globals for I/O port numbers")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: 8d5d45fb14 ("I2C: Move hwmon drivers (2/3)")
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reported-by: John Garry <john.garry@huawei.com>
Cc: John Garry <john.garry@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use [SENSOR_][DEVICE_]ATTR[_2]_{RO,RW,WO} to simplify the source code,
to improve readbility, and to reduce the chance of inconsistencies.
Also replace any remaining S_<PERMS> in the driver with octal values.
The conversion was done automatically with coccinelle. The semantic patches
and the scripts used to generate this commit log are available at
https://github.com/groeck/coccinelle-patches/.
This patch does not introduce functional changes. It was verified by
compiling the old and new files and comparing text and data sizes.
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use SENSOR[_DEVICE]_ATTR[_2]_{RO,RW,WO} to simplify the source code,
to improve readbility, and to reduce the chance of inconsistencies.
Also replace any remaining S_<PERMS> in the driver with octal values.
The conversion was done automatically with coccinelle. The semantic patches
and the scripts used to generate this commit log are available at
https://github.com/groeck/coccinelle-patches/.
This patch does not introduce functional changes. It was verified by
compiling the old and new files and comparing text and data sizes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use SENSOR[_DEVICE]_ATTR[_2]_{RO,RW,WO} to simplify the source code,
to improve readbility, and to reduce the chance of inconsistencies.
Also replace any remaining S_<PERMS> in the driver with octal values.
The conversion was done automatically with coccinelle. The semantic patches
and the scripts used to generate this commit log are available at
https://github.com/groeck/coccinelle-patches/.
This patch does not introduce functional changes. It was verified by
compiling the old and new files and comparing text and data sizes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use SENSOR[_DEVICE]_ATTR[_2]_{RO,RW,WO} to simplify the source code,
to improve readbility, and to reduce the chance of inconsistencies.
Also replace any remaining S_<PERMS> in the driver with octal values.
The conversion was done automatically with coccinelle. The semantic patches
and the scripts used to generate this commit log are available at
https://github.com/groeck/coccinelle-patches/.
This patch does not introduce functional changes. It was verified by
compiling the old and new files and comparing text and data sizes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use SENSOR[_DEVICE]_ATTR[_2]_{RO,RW,WO} to simplify the source code,
to improve readbility, and to reduce the chance of inconsistencies.
Also replace any remaining S_<PERMS> in the driver with octal values.
The conversion was done automatically with coccinelle. The semantic patches
and the scripts used to generate this commit log are available at
https://github.com/groeck/coccinelle-patches/.
This patch does not introduce functional changes. It was verified by
compiling the old and new files and comparing text and data sizes.
Cc: Roger Lucas <vt8231@hiddenengine.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use SENSOR[_DEVICE]_ATTR[_2]_{RO,RW,WO} to simplify the source code,
to improve readbility, and to reduce the chance of inconsistencies.
Also replace any remaining S_<PERMS> in the driver with octal values.
The conversion was done automatically with coccinelle. The semantic patches
and the scripts used to generate this commit log are available at
https://github.com/groeck/coccinelle-patches/.
This patch does not introduce functional changes. It was verified by
compiling the old and new files and comparing text and data sizes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use SENSOR[_DEVICE]_ATTR[_2]_{RO,RW,WO} to simplify the source code,
to improve readbility, and to reduce the chance of inconsistencies.
Also replace any remaining S_<PERMS> in the driver with octal values.
The conversion was done automatically with coccinelle. The semantic patches
and the scripts used to generate this commit log are available at
https://github.com/groeck/coccinelle-patches/.
This patch does not introduce functional changes. It was verified by
compiling the old and new files and comparing text and data sizes.
Cc: Andreas Werner <andreas.werner@men.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use SENSOR[_DEVICE]_ATTR[_2]_{RO,RW,WO} to simplify the source code,
to improve readbility, and to reduce the chance of inconsistencies.
Also replace any remaining S_<PERMS> in the driver with octal values.
The conversion was done automatically with coccinelle. The semantic patches
and the scripts used to generate this commit log are available at
https://github.com/groeck/coccinelle-patches/.
This patch does not introduce functional changes. It was verified by
compiling the old and new files and comparing text and data sizes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use SENSOR[_DEVICE]_ATTR[_2]_{RO,RW,WO} to simplify the source code,
to improve readbility, and to reduce the chance of inconsistencies.
Also replace any remaining S_<PERMS> in the driver with octal values.
The conversion was done automatically with coccinelle. The semantic patches
and the scripts used to generate this commit log are available at
https://github.com/groeck/coccinelle-patches/.
This patch does not introduce functional changes. It was verified by
compiling the old and new files and comparing text and data sizes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use SENSOR[_DEVICE]_ATTR[_2]_{RO,RW,WO} to simplify the source code,
to improve readbility, and to reduce the chance of inconsistencies.
Also replace any remaining S_<PERMS> in the driver with octal values.
The conversion was done automatically with coccinelle. The semantic patches
and the scripts used to generate this commit log are available at
https://github.com/groeck/coccinelle-patches/.
This patch does not introduce functional changes. It was verified by
compiling the old and new files and comparing text and data sizes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use SENSOR[_DEVICE]_ATTR[_2]_{RO,RW,WO} to simplify the source code,
to improve readbility, and to reduce the chance of inconsistencies.
Also replace any remaining S_<PERMS> in the driver with octal values.
The conversion was done automatically with coccinelle. The semantic patches
and the scripts used to generate this commit log are available at
https://github.com/groeck/coccinelle-patches/.
This patch does not introduce functional changes. It was verified by
compiling the old and new files and comparing text and data sizes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use SENSOR[_DEVICE]_ATTR[_2]_{RO,RW,WO} to simplify the source code,
to improve readbility, and to reduce the chance of inconsistencies.
Also replace any remaining S_<PERMS> in the driver with octal values.
The conversion was done automatically with coccinelle. The semantic patches
and the scripts used to generate this commit log are available at
https://github.com/groeck/coccinelle-patches/.
This patch does not introduce functional changes. It was verified by
compiling the old and new files and comparing text and data sizes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use SENSOR[_DEVICE]_ATTR[_2]_{RO,RW,WO} to simplify the source code,
to improve readbility, and to reduce the chance of inconsistencies.
Also replace any remaining S_<PERMS> in the driver with octal values.
The conversion was done automatically with coccinelle. The semantic patches
and the scripts used to generate this commit log are available at
https://github.com/groeck/coccinelle-patches/.
This patch does not introduce functional changes. It was verified by
compiling the old and new files and comparing text and data sizes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use SENSOR[_DEVICE]_ATTR[_2]_{RO,RW,WO} to simplify the source code,
to improve readbility, and to reduce the chance of inconsistencies.
Also replace any remaining S_<PERMS> in the driver with octal values.
The conversion was done automatically with coccinelle. The semantic patches
and the scripts used to generate this commit log are available at
https://github.com/groeck/coccinelle-patches/.
This patch does not introduce functional changes. It was verified by
compiling the old and new files and comparing text and data sizes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use SENSOR[_DEVICE]_ATTR[_2]_{RO,RW,WO} to simplify the source code,
to improve readbility, and to reduce the chance of inconsistencies.
Also replace any remaining S_<PERMS> in the driver with octal values.
The conversion was done automatically with coccinelle. The semantic patches
and the scripts used to generate this commit log are available at
https://github.com/groeck/coccinelle-patches/.
This patch does not introduce functional changes. It was verified by
compiling the old and new files and comparing text and data sizes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use SENSOR[_DEVICE]_ATTR[_2]_{RO,RW,WO} to simplify the source code,
to improve readbility, and to reduce the chance of inconsistencies.
Also replace any remaining S_<PERMS> in the driver with octal values.
The conversion was done automatically with coccinelle. The semantic patches
and the scripts used to generate this commit log are available at
https://github.com/groeck/coccinelle-patches/.
This patch does not introduce functional changes. It was verified by
compiling the old and new files and comparing text and data sizes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: 8d5d45fb14 ("I2C: Move hwmon drivers (2/3)")
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reported-by: John Garry <john.garry@huawei.com>
Cc: John Garry <john.garry@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: ba224e2c4f ("hwmon: New PC87427 hardware monitoring driver")
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reported-by: John Garry <john.garry@huawei.com>
Cc: John Garry <john.garry@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Unable to handle kernel paging request at virtual address ffffffbffee0002e
pgd = ffffffc1d68d4000
[ffffffbffee0002e] *pgd=0000000000000000, *pud=0000000000000000
Internal error: Oops: 94000046 [#1] PREEMPT SMP
Modules linked in: f71805f(+) hwmon
CPU: 3 PID: 1659 Comm: insmod Not tainted 4.5.0+ #88
Hardware name: linux,dummy-virt (DT)
task: ffffffc1f6665400 ti: ffffffc1d6418000 task.ti: ffffffc1d6418000
PC is at f71805f_find+0x6c/0x358 [f71805f]
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple
drivers is synchronized.
Fixes: e53004e20a ("hwmon: New f71805f driver")
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reported-by: John Garry <john.garry@huawei.com>
Cc: John Garry <john.garry@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The following build warning is seen if CONFIG_OF is disabled.
drivers/hwmon/ina2xx.c:510:34: warning:
‘ina2xx_of_match’ defined but not used
Mark ina2xx_of_match as __maybe_unused to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The following build warning is seen if CONFIG_OF is disabled.
drivers/hwmon/lm63.c:1156:34: warning:
‘lm63_of_match’ defined but not used
Mark lm63_of_match as __maybe_unused to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The following build warning is seen if CONFIG_OF is disabled.
drivers/hwmon/lm95245.c:626:34: warning:
‘lm95245_of_match’ defined but not used
Mark lm95245_of_match as __maybe_unused to fix the problem.
The following build warning is always seen.
drivers/hwmon/lm95245.c:95:17: warning:
‘lm95245_reg_address’ defined but not used
The array is no longer used since commit c0a4b9ec1b ("hwmon: (lm95245)
Use new hwmon registration API"). Remove it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The following build warning is seen if CONFIG_OF is disabled.
drivers/hwmon/tmp421.c:73:34: warning:
‘tmp421_of_match’ defined but not used
Mark tmp421_of_match as __maybe_unused to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The following build warning is seen if CONFIG_OF is disabled.
drivers/hwmon/stts751.c:88:34: warning:
‘stts751_of_match’ defined but not used
Mark stts751_of_match as __maybe_unused to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The following build warning is seen if CONFIG_OF is disabled.
drivers/hwmon/max6621.c:573:34: warning:
‘max6621_of_match’ defined but not used
Mark max6621_of_match as __maybe_unused to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The following build warning is seen if CONFIG_OF is disabled.
drivers/hwmon/lm85.c:1645:34: warning:
‘lm85_of_match’ defined but not used
Mark lm85_of_match as __maybe_unused to ix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If CONFIG_OF is not enabled, the following build warning is observed.
drivers/hwmon/max6650.c:137:34: warning:
‘max6650_dt_match’ defined but not used
Mark max6650_dt_match as __maybe_unused to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If CONFIG_OF is not enabled, the following build warning is observed.
drivers/hwmon/max6697.c:653:34: warning:
‘max6697_of_match’ defined but not used
Mark max6697_of_match as __maybe_unused to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If CONFIG_OF is not enabled, the following build warning is observed.
drivers/hwmon/ina209.c:590:34: warning:
‘ina209_of_match’ defined but not used
Mark ina209_of_match as __maybe_unused to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If CONFIG_OF is not enabled, the following build warning is observed.
drivers/hwmon/lm75.c:446:34: warning:
‘lm75_of_match’ defined but not used
Mark lm75_of_match as __maybe_unused to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If CONFIG_OF is not enabled, the following build warning is observed.
drivers/hwmon/w83773g.c:47:34: warning:
‘w83773_of_match’ defined but not used
Mark w83773_of_match as __maybe_unused to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If CONFIG_OF is not enabled, the following build warning is observed.
drivers/hwmon/ads7828.c:203:34: warning:
‘ads7828_of_match’ defined but not used
Mark ads7828_of_match as __maybe_unused to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If CONFIG_OF is not enabled, the following build warning is observed.
drivers/hwmon/hih6130.c:255:34: warning:
‘hih6130_of_match’ defined but not used
Mark hih6130_of_match as __maybe_unused to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If CONFIG_OF is not enabled, the following build warning is observed.
drivers/hwmon/adt7475.c:171:34: warning:
‘adt7475_of_match’ defined but not used
Mark adt7475_of_match as __maybe_unused to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If CONFIG_OF is not enabled, the following build warning is observed.
drivers/hwmon/ads1015.c:310:34: warning:
‘ads1015_of_match’ defined but not used
Marking ads1015_of_match as __maybe_unused fixes the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If CONFIG_OF is not enabled, the following build warning is observed.
drivers/hwmon/tmp103.c:173:34: warning:
‘tmp103_of_match’ defined but not used
Marking tmp103_of_match as __maybe_unused fixes the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If CONFIG_OF is not enabled, the following build warning is observed.
drivers/hwmon/tmp102.c:324:34: warning:
‘tmp102_of_match’ defined but not used
Mark it as __maybe_unused to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If CONFIG_OF is not enabled, the following build warning is observed.
drivers/hwmon/ad7414.c:218:34: warning:
‘ad7414_of_match’ defined but not used
Marking ad7414_of_match as __mayybe_unused fixes the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If CONFIG_OF is not enabled, the following build warning is observed.
drivers/hwmon/adc128d818.c:524:34: warning:
‘adc128_of_match’ defined but not used
Mark adc128_of_match as __maybe_unused to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If CONFIG_OF is not enabled, the following build warning is observed.
drivers/hwmon/lm90.c:239:34: warning:
‘lm90_of_match’ defined but not used
Mark lm90_of_match as __maybe_unused to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If CONFIG_OF is not enabled, the following build warning is observed.
drivers/hwmon/ltc4151.c:211:34: warning:
‘ltc4151_match’ defined but not used
Mark ltc4151_match as __maybe_unused to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If CONFIG_OF is not enabled, the following build warning is observed.
drivers/hwmon/pmbus/ucd9000.c:154:34: warning:
‘ucd9000_of_match’ defined but not used
Mark ucd9000_of_match as __maybe_unused to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If CONFIG_OF is not enabled, the following build warning is observed.
drivers/hwmon/pmbus/tps53679.c💯34: warning:
‘tps53679_of_match’ defined but not used
Marking tps53679_of_match as __maybe_unused fixes the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If CONFIG_OF is not enabled, the following build warning is
observed.
drivers/hwmon/pmbus/ucd9200.c:50:34: warning:
‘ucd9200_of_match’ defined but not used
Mark it as __maybe_unused to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since every call to devm_kasprintf() in the switch statement is mostly
the same, we can move all of the shared code outside and capture
differencies with two helper variables. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The new helper devm_platform_ioremap_resource() wraps
platform_get_resource() and devm_ioremap_resource() together.
Use it to simplify the code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@r@
initializer list elements;
identifier i;
@@
-u32 i[] = {
- elements,
- 0
-};
@s@
identifier r.i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the semantic patch.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@r@
initializer list elements;
identifier i;
@@
-u32 i[] = {
- elements,
- 0
-};
@s@
identifier r.i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the semantic patch.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@r@
initializer list elements;
identifier i;
@@
-u32 i[] = {
- elements,
- 0
-};
@s@
identifier r.i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the semantic patch.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@r@
initializer list elements;
identifier i;
@@
-u32 i[] = {
- elements,
- 0
-};
@s@
identifier r.i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the semantic patch.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@r@
initializer list elements;
identifier i;
@@
-u32 i[] = {
- elements,
- 0
-};
@s@
identifier r.i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the semantic patch.
Cc: Avi Fishman <avifishman70@gmail.com>
Cc: Tomer Maimon <tmaimon77@gmail.com>
Cc: Patrick Venture <venture@google.com>
Cc: Nancy Yuen <yuenn@google.com>
Cc: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@r@
initializer list elements;
identifier i;
@@
-u32 i[] = {
- elements,
- 0
-};
@s@
identifier r.i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the semantic patch.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@r@
initializer list elements;
identifier i;
@@
-u32 i[] = {
- elements,
- 0
-};
@s@
identifier r.i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the semantic patch.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@r@
initializer list elements;
identifier i;
@@
-u32 i[] = {
- elements,
- 0
-};
@s@
identifier r.i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the semantic patch.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@r@
initializer list elements;
identifier i;
@@
-u32 i[] = {
- elements,
- 0
-};
@s@
identifier r.i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the semantic patch.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@r@
initializer list elements;
identifier i;
@@
-u32 i[] = {
- elements,
- 0
-};
@s@
identifier r.i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the semantic patch.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@r@
initializer list elements;
identifier i;
@@
-u32 i[] = {
- elements,
- 0
-};
@s@
identifier r.i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the semantic patch.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@r@
initializer list elements;
identifier i;
@@
-u32 i[] = {
- elements,
- 0
-};
@s@
identifier r.i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the semantic patch.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@r@
initializer list elements;
identifier i;
@@
-u32 i[] = {
- elements,
- 0
-};
@s@
identifier r.i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the semantic patch.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@r@
initializer list elements;
identifier i;
@@
-u32 i[] = {
- elements,
- 0
-};
@s@
identifier r.i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the semantic patch.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@r@
initializer list elements;
identifier i;
@@
-u32 i[] = {
- elements,
- 0
-};
@s@
identifier r.i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the semantic patch.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@r@
initializer list elements;
identifier i;
@@
-u32 i[] = {
- elements,
- 0
-};
@s@
identifier r.i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the semantic patch.
The patch was post-edited to retain comments.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@r@
initializer list elements;
identifier i;
@@
-u32 i[] = {
- elements,
- 0
-};
@s@
identifier r.i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the semantic patch.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The new macro simplifies the code, reduces the likelihood of errors,
and makes the code easier to read.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Lochnagar is an evaluation and development board for Cirrus
Logic Smart CODEC and Amp devices. It allows the connection of
most Cirrus Logic devices on mini-cards, as well as allowing
connection of various application processor systems to provide a
full evaluation platform.
This driver adds support for the hardware monitoring features of
the Lochnagar 2 to the hwmon API. Monitoring is provided for
the board voltages, currents and temperature supported by the
board controller chip.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for fan capability registers in order to distinct between
the systems which have minor fan configuration differences. This
reduces the amount of code used to describe such systems.
The capability registers provides system specific information about the
number of physically connected tachometers and system specific fan
speed scale parameter.
For example one system can be equipped with twelve fan tachometers,
while the other with for example, eight or six. Or one system should
use default fan speed divider value, while the other has a scale
parameter defined in hardware, which should be used for divider
setting.
Reading this information from the capability registers allows to use the
same fan structure for the systems with the such differences.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The occ's extended status is checked and shown as sysfs attributes. But
the code was incorrectly checking the "status" bits.
Fix it by checking the "ext_status" bits.
Cc: stable@vger.kernel.org
Fixes: df04ced684 ("hwmon (occ): Add sysfs attributes for additional OCC data")
Signed-off-by: Lei YU <mine260309@gmail.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In case pwm_fan_of_get_cooling_data() fails we should disable the PWM
just like in the other error cases.
Fixes: 2e5219c771 ("hwmon: (pwm-fan) Read PWM FAN configuration from device tree")
Cc: <stable@vger.kernel.org> # 4.14+
Reported-by: Guenter Rock <linux@roeck-us.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 7cc7de93fa ("hwmon: (ntc_thermistor) Convert to new hwmon API")
converted the driver to use the new hwmon API, but introduced a subtle
error: The temperature type is no longer reported as temp1_type, but as
temp2_type.
Fixes: 7cc7de93fa ("hwmon: (ntc_thermistor) Convert to new hwmon API")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In the case of power sensor version 0xA0, the sensor indexing overlapped
with the "caps" power sensors, resulting in probe failure and kernel
warnings. Fix this by specifying the next index for each power sensor
version.
Fixes: 54076cb3b5 ("hwmon (occ): Add sensor attributes and register ...")
Cc: stable@vger.kernel.org
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This adds device tree probing for the AD7418 hwmon sensor.
When device tree is not enabled, stub functions will kick
in.
Tested on the Gateway Cambria GW2358-4.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[groeck: Added missing {} to terminate ad7418_dt_ids]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_hwmon_device_register_with_info() instead of
devm_hwmon_device_register_with_groups() to register the hwmon
device to simplify the code and make it easier to maintain.
As part of this change, thermal device registration is moved into
the hwmon core.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This adds optional regulator support to the pwm-fan driver. This is
necessary for pwm fans which are powered by a switchable supply.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/hwmon/f71882fg.c: In function ‘f71882fg_probe’:
drivers/hwmon/f71882fg.c:2457:33: warning: this statement may fall through [-Wimplicit-fallthrough=]
data->auto_point_temp_signed = 1;
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~
drivers/hwmon/f71882fg.c:2459:3: note: here
case f71889fg:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If there is an i2c failure, the ad7416 reports its temperature as 0C.
Return an error code so users can properly detect errors.
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The LM96000 expands the freqency field from 3 to 4 bits, to
add more frequencies in the 22.5 to 30 kHz ranges.
Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It has been supported as a generic lm85 for quite some time.
Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Nicolin Chen
Mauro Carvalho Chehab
Eddie James
Maxim Sloyko
krzysztof.adamski@nokia.com
Guenter Roeck
Robin Murphy
Stefan Wahren
Jean Delvare
Andrey Smirnov
Lucas Tanure
Vadim Pasternak
Lei YU
Axel Lin
Linus Walleij
Gustavo A. R. Silva
Brandon Maier
Jeremy Gebben