Fireface UFX was shipped by RME GmbH in 2010, and now discontinued.
Although this model has some enhanced feature which Fireface 802
doesn't have (e.g. on-board USB mass storage device class, configuration
interface with color display), the functionality relevant to
packet communication on IEEE 1394 bus seems to be the same as
Fireface 802 (e.g. available number of channels for PCM frame in
each sampling transfer frequency).
With the assumption, this commit adds support for Fireface UFX. In ALSA
fireface driver, these two models are handled as the same one.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20200510074301.116224-7-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireface 802 was shipped by RME GmbH in 2014. This model supports later
protocol for management of isochronous communication and synchronization
of sampling transmission frequency.
This model consists of below ICs:
* TI TSB41AB2
* Xilinx Spartan-6 FPGA XC6SLX16
* TI TMS320 C6747
* SMSC USB3250
Especially, this model just supports IEEE 1394a, against its name which
evokes Fireface 800.
This commit adds support for Fireface 802 (tested). Userspace applications
can transfer PCM frames and MIDI messages via ALSA PCM/Rawmidi interface.
I note that 4 channels for ADAt1 and ADAT2 are disabled at higher sampling
transfer frequency since isochronous resources reservation fails due to
bandwidth limitation of IEEE 1394a.
The value read from LATTER_SYNC_STATUS register is slightly different
from the one of Fireface UCX. The higher 4 bits and lower 4 bits are
swapped within the same byte.
Without any assist of userspace application, transmitted MIDI messages
from the device are not going to be processed. For detail, please refer
to my comment in code of latter protocol.
$ python crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 0404ffff bus_info_length 4, crc_length 4, crc 65535 (should be 26805)
404 31333934 bus_name "1394"
408 20008000 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 0, max_rec 8 (512)
40c 000a3504 company_id 000a35 |
410 38077423 device_id 0438077423 | EUI-64 000a350438077423
root directory
-----------------------------------------------------------------
414 0005ffff directory_length 5, crc 65535 (should be 9514)
418 0c0083c0 node capabilities per IEEE 1394
41c 03000a35 vendor
420 8100000b --> descriptor leaf at 44c
424 8d000007 --> eui-64 leaf at 440
428 d1000001 --> unit directory at 42c
unit directory at 42c
-----------------------------------------------------------------
42c 0004ffff directory_length 4, crc 65535 (should be 45134)
430 12000a35 specifier id
434 13000005 version
438 17101800 model
43c 81000008 --> descriptor leaf at 45c
eui-64 leaf at 440
-----------------------------------------------------------------
440 0002ffff leaf_length 2, crc 65535 (should be 60131)
444 000a3504 company_id 000a35 |
448 38077423 device_id 0438077423 | EUI-64 000a350438077423
descriptor leaf at 44c
-----------------------------------------------------------------
44c 0003ffff leaf_length 3, crc 65535 (should be 469)
450 00000000 textual descriptor
454 00000000 minimal ASCII
458 524d4521 "RME!"
descriptor leaf at 45c
-----------------------------------------------------------------
45c 0005ffff leaf_length 5, crc 65535 (should be 10561)
460 00000000 textual descriptor
464 00000000 minimal ASCII
468 46697265 "Fire"
46c 66616365 "face"
470 20383032 " 802"
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20200510074301.116224-6-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In RME fireface series, version field of unit directory in configuration
ROM is used to distinguish each model. The value of field is known and
it's better to use enumeration constants for code representation.
This commit adds enumeration constants for model identification.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20200510074301.116224-4-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the latter models of RME Fireface series, device start to transfer
packets several dozens of milliseconds. On the other hand, ALSA fireface
driver starts IR context 2 milliseconds after the start. This results
in loss to handle incoming packets on the context.
This commit changes to start IR context immediately instead of
postponement. For Fireface 800, this affects nothing because the device
transfer packets 100 milliseconds or so after the start and this is
within wait timeout.
Cc: <stable@vger.kernel.org>
Fixes: acfedcbe1c ("ALSA: firewire-lib: postpone to start IR context")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20200510074301.116224-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
128000 and 192000 are congruence modulo 32000, thus it's wrong to
distinguish them as multiple of 32000 and 48000 by modulo 32000 at
first.
Additionally, used condition statement to detect quadruple speed can
cause missing bit flag.
Furthermore, counter to ensure the configuration is wrong and it
causes false positive.
This commit fixes the above three bugs.
Cc: <stable@vger.kernel.org>
Fixes: 60aec494b3 ("ALSA: fireface: support allocate_resources operation in latter protocol")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20200510074301.116224-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
KBUILD_MODNAME is available to name kernel modules according to its object
name. This commit uses the macro instead of string for name field of
struct driver since drivers in ALSA firewire stack have the same name of
each object name.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20200306135229.11659-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
All the PCM ioctl ops of ALSA FireWire drivers do nothing but calling
the default handler.
Now PCM core accepts NULL as the default ioctl ops(*), so let's drop
altogether.
(*) commit fc033cbf6f ("ALSA: pcm: Allow NULL ioctl ops")
Acked-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191210061145.24641-6-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clean up the drivers with the new managed buffer allocation API.
The superfluous snd_pcm_lib_malloc_pages() and
snd_pcm_lib_free_pages() calls are dropped.
Acked-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191209192422.23902-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent change (*) in the ALSA memalloc core allows us to drop the
special vmalloc-specific allocation and page handling. This patch
coverts to the common code.
(*) 1fe7f397cfe2: ALSA: memalloc: Add vmalloc buffer allocation
support
7e8edae39fd1: ALSA: pcm: Handle special page mapping in the
default mmap handler
Link: https://lore.kernel.org/r/20191105151856.10785-11-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some devices have a quirk to postpone transmission of isoc packet for
several dozen or hundred isoc cycles since configured to transmit.
Furthermore, some devices have a quirk to transmit isoc packet with
discontinued data of its header.
In 1394 OHCI specification, software allows to start isoc context with
certain isoc cycle. Linux firewire subsystem has kernel API to use it
as well.
This commit uses the functionality of 1394 OHCI controller to handle
the quirks. At present, this feature is convenient to ALSA bebob and
fireface driver. As a result, some devices can be safely handled, as
long as I know:
- MAudio FireWire solo
- MAudio ProFire Lightbridge
- MAudio FireWire 410
- Roland FA-66
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191018061911.24909-7-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
An isoc context for AMDTP stream is flushed to queue packet
by a call of pcm.ack. This commit extends this for AMDTP
domain.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191018061911.24909-4-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
An isoc context for AMDTP stream is flushed to queue packet
by a call of pcm.pointer. This commit extends this for AMDTP
domain.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191018061911.24909-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit allows ALSA fireface driver to share PCM buffer size for
both capture and playback PCM substream. When AMDTP domain starts for
one of the PCM substream, buffer size of the PCM substream is stores to
AMDTP domain structure. Some AMDTP streams have already run with the
buffer size when another PCM substream starts, therefore the PCM
substream has a constraint to its buffer size.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191017155424.885-10-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The number of packets in packet buffer has been fixed number (=48) since
first commit of ALSA IEC 61883-1/6 packet streaming engine.
This commit allows the engine to use variable number of packets in the
buffer. The size is calculated by a parameter in AMDTP domain structure
surely to store the number of events in the packets of buffer. Although
the value of parameter is expected to come from 'period size' parameter
of PCM substream, at present 48 is still used.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191017155424.885-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In current implementation, when opening a PCM substream, it's needed to
check whether the opposite PCM substream runs. This is to assign
effectual constraints (e.g. sampling rate) to opened PCM substream.
The number of PCM substreams on AMDTP streams in domain is recorded in
own structure. Usage of this count is an alternative of the above check.
This is better because the count is incremented in pcm.hw_params earlier
than pcm.trigger.
This commit replaces the check with the substream count and the value for
the size of PCM period. Unlike the other drivers in ALSA firewire stack,
no MIDI substream is multiplexed into AMDTP stream.
I note that Fireface AMDTP protocol has a quirk that tx stream includes
blank isochronous cycle. The packet for blank cycle is equivalent to
empty or NODATA packet in IEC 61883-6, thus the protocol is similar to
blocking transmission method of IEC 61883-6. On the other hand, rx
stream adopts non-blocking transmission method. Although the difference
of transmission method between tx/rx streams precisely brings different
timing for a certain amount of events due to their different calculation
for data blocks per packet, it's possible to approximate enough amount
of events mostly has the same timing. Actually current ALSA IEC 61883-1/6
engine uses large amount of data blocks for each hardware IRQ
(=16 packets).
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191007110532.30270-18-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a preparation to share the size of PCM period between
PCM substreams on AMDTP streams in the same domain. At this time,
the size of PCM period in PCM substream which starts AMDTP streams in the
same domain is recorded.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191007110532.30270-10-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a preparation to support AMDTP domain.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit changes each of data block processing layer so that it
receives list of packet descriptor.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is code refactoring for FF data block processing layer so that
it can receive list of packet descriptor.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit changes signature of callback function to call data block
processing layer with packet descriptor. At present, the layer is called
per packet.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In a previous commit, the variable passed from packet streaming layer
for syt variable is useless. This commit obsoletes it.
In my future work, the syt information is passed to data block processing
layer by another way.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a preparation for future commit that 'struct
amdtp_stream.data_block_count' does not represent the value of
data block count for current data block.
However, data block count is required for calculation of sequence index
in sequence-multiplied data channel. Some of data block processing layer
require it; e.g. for AM824 data block.
This commit passes data block count to the processing layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a very big update, mainly thanks to Morimoto-san's refactoring
work and some fairly large new drivers.
- Lots more work on moving towards a component based framework from
Morimoto-san.
- Support for force disconnecting muxes from Jerome Brunet.
- New drivers for Cirrus Logic CS47L35, CS47L85 and CS47L90, Conexant
CX2072X, Realtek RT1011 and RT1308.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl0jGwUTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0LD4B/9AkutfS+vznOrk0V0wFb2SUfjwE4Pr
+z/kAehohAOl/7pg9Dun/lmZYBWMyOM2aYmK81ahEo2DfO+uzwkwjCaXFjGVGwEK
j7XpWkrIjKnou/z1FeALgVvt+crzdy5iNWC04AbKaP2WHCcI7zvPQIsBta/V0OJt
lg+j0J7pagnTMcgV1+qJdaASmofy/hpoZ79Gv0PIfGC8hpJ/3mBgcNPCLQrJtD4R
v+tzvCZNrZVqCanwLf3vouEm1bpWYOpI+Wdmu4u6rY7MhmCj72EJ2zyfdm/qtaxF
e7whgCyOQFkWe7NgDn0G08aAT6LsaxOtPNr7H8tL8S8sw8425fqeOouV
=n/HQ
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.3' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v5.3
This is a very big update, mainly thanks to Morimoto-san's refactoring
work and some fairly large new drivers.
- Lots more work on moving towards a component based framework from
Morimoto-san.
- Support for force disconnecting muxes from Jerome Brunet.
- New drivers for Cirrus Logic CS47L35, CS47L85 and CS47L90, Conexant
CX2072X, Realtek RT1011 and RT1308.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This back-merge is necessary for adjusting the latest FireWire fix
with the recent refactoring in 5.3 development branch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
>From callbacks for pcm and rawmidi interfaces, the functions to stop
and release duplex streams are called at the same time. This commit
merges the two functions.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The pairs of pcm.hw_params callbacks and .hw_free callbacks for both
direction have no differences.
This commit unifies the pairs.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The operation to finish packet streaming corresponds to stopping
isochronous contexts.
This commit applies code refactoring to move codes to stop into
a helper function to finish the session.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After bus reset, isochronous resource manager releases all of allocated
isochronous resources. The nodes to restart packet streaming should
request reallocation of the resources.
However, between the bus-reset and invocation of 'struct fw_driver.update'
handler, ALSA PCM application can detect this situation by XRUN because
the target device cancelled to transmit packets once bus-reset occurs.
Due to the above mechanism, ALSA fireface driver just stops packet
streaming in the update handler, thus pcm.prepare handler should
request the reallocation.
This commit requests the reallocation in pcm.prepare callback when
bus generation is changed.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Once allocated, isochronous resources are available for packet
streaming, even if the streaming is cancelled. For this reason,
current implementation handles allocation of the resources and
starting packet streaming at the same time. However, this brings
complicated procedure to start packet streaming.
This commit separates the allocation and starting. The allocation is
done in pcm.hw_params callback and available till pcm.hw_free callback.
Even if any XRUN occurs, pcm.prepare callback is done to restart
packet streaming for allocated the resources.
There are two points to stop packet streaming; in pcm.hw_params and
pcm.prepare callbacks.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a part of preparation to perform allocation/release
of isochronous channels in pcm.hw_params/hw_free callbacks.
This commit implements allocate_resources callback for the protocol
specific to latter models. The encoded values of constant table is
split into several condition statements to separate the operation
to configure sampling transfer frequency from the operation to
configure the number of data channels in rx packet.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a part of preparation to perform allocation/release
of isochronous channels in pcm.hw_params/hw_free callbacks.
This commit implements allocate_resources callback for ff400 protocol.
In this callback, sampling transfer frequency is configured to the
device as well.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a part of preparation to perform allocation/release
of isochronous channels in pcm.hw_params/hw_free callbacks.
This commit implements allocate_resources callback for ff800 protocol.
As I noted in commit fc716397a5 ("ALSA: fireface: add support for
packet streaming on Fireface 800"), this unit allocates isochronous
resources for tx stream voluntarily. Therefore, this commit is to
maintain isochronous rsources for rx stream. In the callback,
sampling transfer frequency is configured to the device as well.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a part of preparation to perform allocation/release
of isochronous channels in pcm.hw_params/hw_free callbacks.
In ALSA fireface driver, the allocation of isochronous resources is
programmed in each implementation of protocol. This commit adds
protocol-specific operation for the allocation separated from
the operation to begin session.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Based on 1 normalized pattern(s):
licensed under the terms of the gnu general public license version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 88 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000437.521539229@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No big surprises here, just a few device-specific fixes.
HD-audio received several fixes for Acer, Dell, Huawei and other
laptops as well as the workaround for the new Intel chipset.
One significant one-liner fix is the disablement of the node-power
saving on Realtek codecs, which may potentially cover annoying bugs
like the background noises or click noises on many devices.
Other than that, a fix for FireWire bit definitions, and another fix
for LINE6 USB audio bug that was discovered by syzkaller.
-----BEGIN PGP SIGNATURE-----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=Bj5P
-----END PGP SIGNATURE-----
Merge tag 'sound-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"No big surprises here, just a few device-specific fixes.
HD-audio received several fixes for Acer, Dell, Huawei and other
laptops as well as the workaround for the new Intel chipset. One
significant one-liner fix is the disablement of the node-power saving
on Realtek codecs, which may potentially cover annoying bugs like the
background noises or click noises on many devices.
Other than that, a fix for FireWire bit definitions, and another fix
for LINE6 USB audio bug that was discovered by syzkaller"
* tag 'sound-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: fireface: Use ULL suffixes for 64-bit constants
ALSA: hda/realtek - Improve the headset mic for Acer Aspire laptops
ALSA: line6: Assure canceling delayed work at disconnection
ALSA: hda - Force polling mode on CNL for fixing codec communication
ALSA: hda/realtek - Enable micmute LED for Huawei laptops
ALSA: hda/realtek - Set default power save node to 0
ALSA: hda/realtek - Check headset type by unplug and resume
With gcc 4.1:
sound/firewire/fireface/ff-protocol-latter.c: In function ‘latter_switch_fetching_mode’:
sound/firewire/fireface/ff-protocol-latter.c:97: warning: integer constant is too large for ‘long’ type
sound/firewire/fireface/ff-protocol-latter.c: In function ‘latter_begin_session’:
sound/firewire/fireface/ff-protocol-latter.c:170: warning: integer constant is too large for ‘long’ type
sound/firewire/fireface/ff-protocol-latter.c:197: warning: integer constant is too large for ‘long’ type
sound/firewire/fireface/ff-protocol-latter.c:205: warning: integer constant is too large for ‘long’ type
sound/firewire/fireface/ff-protocol-latter.c: In function ‘latter_finish_session’:
sound/firewire/fireface/ff-protocol-latter.c:214: warning: integer constant is too large for ‘long’ type
Fix this by adding the missing "ULL" suffixes.
Add the same suffix to the last constant, to maintain consistency.
Fixes: fd1cc9de64 ("ALSA: fireface: add support for Fireface UCX")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The calls of snd_info_register() are superfluous and should be avoided
at the procfs creation time. They are called at the end of the whole
initialization via snd_card_register(). This patch drops such
superfluous calls.
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Tested-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The > should be >= or otherwise we potentially read one element beyond
the end of the ff->tx_midi_substreams[] array.
Fixes: 73f5537fb2 ("ALSA: fireface: support tx MIDI functionality of Fireface UCX")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In Fireface series, registration of higher 4 bytes of destination
address for asynchronous transaction of MIDI messages is done by
a write transaction to model-specific register.
On the other hand, registration of lower 4 bytes of the address is
selectable from 4 options. A register for this registration includes
the other purpose options such as input attenuation. Thus this
driver expects userspace applications to configure the register.
Actual behaviour for the asynchronous transaction is different
depending on protocols. In former protocol, destination offset
of each transaction is the same as the registered address even if
it is block request. In latter models, destination offset of each
transaction is the offset of previous transaction plus 4 byte
and the transaction is quadlet request.
This commit cleanups comments about the above mechanism.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In latter model of Fireface series, asynchronous transaction includes
a prefix byte to indicate the way to decode included MIDI bytes.
Upper 4 bits of the prefix byte indicates port number, and the rest 4
bits indicate the way to decode rest of bytes for MIDI messages.
Basically the rest bits indicates the number of bytes for MIDI message.
However, if the last byte of each MIDi message is included, the rest
bits are 0xf. For example:
message: f0 00 00 66 14 20 00 00 f7
offset: content (big endian, port 0)
'0030: 0x02f00000
'0030: 0x03006614
'0030: 0x03200000
'0030: 0x0ff70000
This commit supports encoding scheme for the above and allows
applications to transfer MIDI messages via ALSA rawmidi interface.
An unused member (running_status) is reused to keep state of
transmission of system exclusive messages.
For your information, this is a dump of config rom.
$ sudo ./hinawa-config-rom-printer /dev/fw1
{ 'bus-info': { 'bmc': False,
'chip_ID': 13225063715,
'cmc': False,
'cyc_clk_acc': 0,
'imc': False,
'isc': True,
'max_rec': 512,
'name': '1394',
'node_vendor_ID': 2613},
'root-directory': [ [ 'NODE_CAPABILITIES',
{ 'addressing': {'64': True, 'fix': True, 'prv': False},
'misc': {'int': False, 'ms': False, 'spt': True},
'state': { 'atn': False,
'ded': False,
'drq': True,
'elo': False,
'init': False,
'lst': True,
'off': False},
'testing': {'bas': False, 'ext': False}}],
['VENDOR', 2613],
['DESCRIPTOR', 'RME!'],
['EUI_64', 2873037108442403],
[ 'UNIT',
[ ['SPECIFIER_ID', 2613],
['VERSION', 4],
['MODEL', 1054720],
['DESCRIPTOR', 'Fireface UCX']]]]}
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Between former and latter models, content of asynchronous transaction
for MIDI messages from driver to device is different.
This commit is a preparation to support latter models. A protocol-specific
operation is added to encode MIDI messages to the transaction.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Between former and latter models, destination address to receive
asynchronous transactions for MIDI messages is different.
This commit adds model-dependent parameter for the addresses.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireface UCX transfers asynchronous transactions for MIDI messages.
One transaction includes quadlet data therefore it can transfer 3
message bytes as maximum. Base address of the destination is
configured by two settings; a register for higher 8 byte of the
address, and a bitflag to option register indicates lower 8byte.
The register for higher address is 0x'ffff'0000'0034. Unfortunately,
firmware v24 includes a bug to ignore registered value for the
destination address and transfers to 0x0001xxxxxxxx always. This
driver doesn't work well if the bug exists, therefore users should
install the latest firmware (v27).
The bitflag is a part of value to be written to option register
(0x'ffff'0000'0014).
lower addr: bitflag (little endian)
'0000'0000: 0x00002000
'0000'0080: 0x00004000
'0000'0100: 0x00008000
'0000'0180: 0x00010000
This register includes more options but they are not relevant to
packet streaming or MIDI functionality. This driver don't touch it.
Furthermore, the transaction is sent to address offset incremented
by 4 byte to the offset in previous time. When it reaches base address
plus 0x7c, next offset is the base address.
Content of the transaction includes a prefix byte. Upper 4 bits of
the byte indicates port number, and the rest 4 bits indicate the way
to decode rest of bytes for MIDI message.
Except for system exclusive messages, the rest bits are the same as
status bits of the message without channel bits. For system exclusive
messages, the rest bits are encoded according to included message bytes.
For example:
message: f0 7e 7f 09 01 f7
offset: content (little endian, port 0)
'0000: 0x04f07e7f
'0004: 0x070901f7
message: f0 00 00 66 14 20 00 00 00 f7
offset: content (little endian, port 1)
'0014: 0x14f00000
'0018: 0x14661420
'001c: 0x14000000
'0020: 0x15f70000
message: f0 00 00 66 14 20 00 00 f7
offset: content (little endian, port 0)
'0078: 0x04f00000
'007c: 0x04661420
'0000: 0x070000f7
This commit supports decoding scheme for the above and allows
applications to receive MIDI messages via ALSA rawmidi interface.
The lower 8 bytes of destination address is fixed to 0x'0000'0000,
thus this driver expects userspace applications to configure option
register with bitflag 0x00002000 in advance.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In Fireface series, drivers can register destination address for
asynchronous transaction which transfers MIDI messages from device.
In former models, all of the transactions arrive at the registered
address without any offset. In latter models, each of the transaction
arrives at the registered address with sequential offset within 0x00
to 0x7f. This seems to be for discontinuity detection.
This commit adds model-dependent member for the address range.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In a series of Fireface, devices transfer asynchronous transaction with
MIDI messages. In the transaction, content is different depending on
models. ALSA fireface driver has protocol-dependent handler to pick up
MIDI messages from the content.
In latter models of the series, the transaction is transferred to range
of address sequentially. This seems to check continuity of transferred
messages.
This commit changes prototype of the handler to receive offset of
address for received transactions.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireface UFX was shipped by RME GmbH in 2012. This model supports later
protocol for management of isochronous communication and synchronization
of sampling transmission frequency.
This commit adds support for the model. At present, it's not clear how
to encode MIDI messages and decide destination address for asynchronous
transaction, thus this commit adds support for isochronous communication
for PCM frames only.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Sakamoto
Takashi Iwai
Thomas Gleixner
Linus Torvalds
Geert Uytterhoeven
Dan Carpenter