We use lockless lists for the local and deferred task_work, which means
that when we queue up events for processing, we ultimately process them
in reverse order to how they were received. This usually doesn't matter,
but for some cases, it does seem to make a big difference. Do the right
thing and reverse the list before processing it, so that we know it's
processed in the same order in which it was received.
This makes a rather big difference for some medium load network tests,
where consistency of performance was a bit all over the place. Here's
a case that has 4 connections each doing two sends and receives:
io_uring port=10002: rps:161.13k Bps: 1.45M idle=256ms
io_uring port=10002: rps:107.27k Bps: 0.97M idle=413ms
io_uring port=10002: rps:136.98k Bps: 1.23M idle=321ms
io_uring port=10002: rps:155.58k Bps: 1.40M idle=268ms
and after the change:
io_uring port=10002: rps:205.48k Bps: 1.85M idle=140ms user=40ms
io_uring port=10002: rps:203.57k Bps: 1.83M idle=139ms user=20ms
io_uring port=10002: rps:218.79k Bps: 1.97M idle=106ms user=30ms
io_uring port=10002: rps:217.88k Bps: 1.96M idle=110ms user=20ms
io_uring port=10002: rps:222.31k Bps: 2.00M idle=101ms user=0ms
io_uring port=10002: rps:218.74k Bps: 1.97M idle=102ms user=20ms
io_uring port=10002: rps:208.43k Bps: 1.88M idle=125ms user=40ms
using more of the time to actually process work rather than sitting
idle.
No effects have been observed at the peak end of the spectrum, where
performance is still the same even with deep batch depths (and hence
more items to sort).
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If we're doing multishot receives, then we always end up doing two trips
through sock_recvmsg(). For protocols that sanely set msghdr->msg_inq,
then we don't need to waste time picking a new buffer and attempting a
new receive if there's nothing there.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Rather than have this logic in both io_recv() and io_recvmsg_multishot(),
push it into the handler they both call when finishing a receive
operation.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We can't currently tell if ->msg_inq was set when we ask for msg_get_inq,
initialize it to -1U so we can tell apart if it was set and there's
no data left, or if it just wasn't set at all by the protocol.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With IORING_REGISTER_USE_REGISTERED_RING, an application can register
the ring fd and use it via registered index rather than installed fd.
This allows using a registered ring for everything *except* the initial
mmap.
With IORING_SETUP_NO_MMAP, io_uring_setup uses buffers allocated by the
user, rather than requiring a subsequent mmap.
The combination of the two allows a user to operate *entirely* via a
registered ring fd, making it unnecessary to ever install the fd in the
first place. So, add a flag IORING_SETUP_REGISTERED_FD_ONLY to make
io_uring_setup register the fd and return a registered index, without
installing the fd.
This allows an application to avoid touching the fd table at all, and
allows a library to never even momentarily install a file descriptor.
This splits out an io_ring_add_registered_file helper from
io_ring_add_registered_fd, for use by io_uring_setup.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Link: https://lore.kernel.org/r/bc8f431bada371c183b95a83399628b605e978a3.1682699803.git.josh@joshtriplett.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently io_uring applications must call mmap(2) twice to map the rings
themselves, and the sqes array. This works fine, but it does not support
using huge pages to back the rings/sqes.
Provide a way for the application to pass in pre-allocated memory for
the rings/sqes, which can then suitably be allocated from shmfs or
via mmap to get huge page support.
Particularly for larger rings, this reduces the TLBs needed.
If an application wishes to take advantage of that, it must pre-allocate
the memory needed for the sq/cq ring, and the sqes. The former must
be passed in via the io_uring_params->cq_off.user_data field, while the
latter is passed in via the io_uring_params->sq_off.user_data field. Then
it must set IORING_SETUP_NO_MMAP in the io_uring_params->flags field,
and io_uring will then map the existing memory into the kernel for shared
use. The application must not call mmap(2) to map rings as it otherwise
would have, that will now fail with -EINVAL if this setup flag was used.
The pages used for the rings and sqes must be contigious. The intent here
is clearly that huge pages should be used, otherwise the normal setup
procedure works fine as-is. The application may use one huge page for
both the rings and sqes.
Outside of those initialization changes, everything works like it did
before.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We do rings and sqes separately, move them into a helper that does both
the freeing and clearing of the memory.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In preparation for having more than one time of ring allocator, make the
existing one return valid/error-pointer rather than just NULL.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We only have two reserved members we're not clearing, do so manually
instead. This is in preparation for using one of these members for
a new feature.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that we have both sockets and block devices setting FMODE_NOWAIT
appropriately, we can get rid of all the odd special casing in
__io_file_supports_nowait() and rely soley on FMODE_NOWAIT and
O_NONBLOCK rather than special case sockets and (in particular) bdevs.
Link: https://lore.kernel.org/r/20230509151910.183637-4-axboe@kernel.dk
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=l7Mo
-----END PGP SIGNATURE-----
Merge tag 'for-6.4/io_uring-2023-05-07' of git://git.kernel.dk/linux
Pull more io_uring updates from Jens Axboe:
"Nothing major in here, just two different parts:
- A small series from Breno that enables passing the full SQE down
for ->uring_cmd().
This is a prerequisite for enabling full network socket operations.
Queued up a bit late because of some stylistic concerns that got
resolved, would be nice to have this in 6.4-rc1 so the dependent
work will be easier to handle for 6.5.
- Fix for the huge page coalescing, which was a regression introduced
in the 6.3 kernel release (Tobias)"
* tag 'for-6.4/io_uring-2023-05-07' of git://git.kernel.dk/linux:
io_uring: Remove unnecessary BUILD_BUG_ON
io_uring: Pass whole sqe to commands
io_uring: Create a helper to return the SQE size
io_uring/rsrc: check for nonconsecutive pages
In the io_uring_cmd_prep_async() there is an unnecessary compilation time
check to check if cmd is correctly placed at field 48 of the SQE.
This is unnecessary, since this check is already in place at
io_uring_init():
BUILD_BUG_SQE_ELEM(48, __u64, addr3);
Remove it and the uring_cmd_pdu_size() function, which is not used
anymore.
Keith started a discussion about this topic in the following thread:
Link: https://lore.kernel.org/lkml/ZDBmQOhbyU0iLhMw@kbusch-mbp.dhcp.thefacebook.com/
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/20230504121856.904491-4-leitao@debian.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently uring CMD operation relies on having large SQEs, but future
operations might want to use normal SQE.
The io_uring_cmd currently only saves the payload (cmd) part of the SQE,
but, for commands that use normal SQE size, it might be necessary to
access the initial SQE fields outside of the payload/cmd block. So,
saves the whole SQE other than just the pdu.
This changes slightly how the io_uring_cmd works, since the cmd
structures and callbacks are not opaque to io_uring anymore. I.e, the
callbacks can look at the SQE entries, not only, in the cmd structure.
The main advantage is that we don't need to create custom structures for
simple commands.
Creates io_uring_sqe_cmd() that returns the cmd private data as a null
pointer and avoids casting in the callee side.
Also, make most of ublk_drv's sqe->cmd priv structure into const, and use
io_uring_sqe_cmd() to get the private structure, removing the unwanted
cast. (There is one case where the cast is still needed since the
header->{len,addr} is updated in the private structure)
Suggested-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/20230504121856.904491-3-leitao@debian.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Create a simple helper that returns the size of the SQE. The SQE could
have two size, depending of the flags.
If IO_URING_SETUP_SQE128 flag is set, then return a double SQE,
otherwise returns the sizeof of io_uring_sqe (64 bytes).
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/20230504121856.904491-2-leitao@debian.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pages that are from the same folio do not necessarily need to be
consecutive. In that case, we cannot consolidate them into a single bvec
entry. Before applying the huge page optimization from commit 57bebf807e
("io_uring/rsrc: optimise registered huge pages"), check that the memory
is actually consecutive.
Cc: stable@vger.kernel.org
Fixes: 57bebf807e ("io_uring/rsrc: optimise registered huge pages")
Signed-off-by: Tobias Holl <tobias@tholl.xyz>
[axboe: formatting]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Core
----
- Introduce a config option to tweak MAX_SKB_FRAGS. Increasing the
default value allows for better BIG TCP performances.
- Reduce compound page head access for zero-copy data transfers.
- RPS/RFS improvements, avoiding unneeded NET_RX_SOFTIRQ when possible.
- Threaded NAPI improvements, adding defer skb free support and unneeded
softirq avoidance.
- Address dst_entry reference count scalability issues, via false
sharing avoidance and optimize refcount tracking.
- Add lockless accesses annotation to sk_err[_soft].
- Optimize again the skb struct layout.
- Extends the skb drop reasons to make it usable by multiple
subsystems.
- Better const qualifier awareness for socket casts.
BPF
---
- Add skb and XDP typed dynptrs which allow BPF programs for more
ergonomic and less brittle iteration through data and variable-sized
accesses.
- Add a new BPF netfilter program type and minimal support to hook
BPF programs to netfilter hooks such as prerouting or forward.
- Add more precise memory usage reporting for all BPF map types.
- Adds support for using {FOU,GUE} encap with an ipip device operating
in collect_md mode and add a set of BPF kfuncs for controlling encap
params.
- Allow BPF programs to detect at load time whether a particular kfunc
exists or not, and also add support for this in light skeleton.
- Bigger batch of BPF verifier improvements to prepare for upcoming BPF
open-coded iterators allowing for less restrictive looping capabilities.
- Rework RCU enforcement in the verifier, add kptr_rcu and enforce BPF
programs to NULL-check before passing such pointers into kfunc.
- Add support for kptrs in percpu hashmaps, percpu LRU hashmaps and in
local storage maps.
- Enable RCU semantics for task BPF kptrs and allow referenced kptr
tasks to be stored in BPF maps.
- Add support for refcounted local kptrs to the verifier for allowing
shared ownership, useful for adding a node to both the BPF list and
rbtree.
- Add BPF verifier support for ST instructions in convert_ctx_access()
which will help new -mcpu=v4 clang flag to start emitting them.
- Add ARM32 USDT support to libbpf.
- Improve bpftool's visual program dump which produces the control
flow graph in a DOT format by adding C source inline annotations.
Protocols
---------
- IPv4: Allow adding to IPv4 address a 'protocol' tag. Such value
indicates the provenance of the IP address.
- IPv6: optimize route lookup, dropping unneeded R/W lock acquisition.
- Add the handshake upcall mechanism, allowing the user-space
to implement generic TLS handshake on kernel's behalf.
- Bridge: support per-{Port, VLAN} neighbor suppression, increasing
resilience to nodes failures.
- SCTP: add support for Fair Capacity and Weighted Fair Queueing
schedulers.
- MPTCP: delay first subflow allocation up to its first usage. This
will allow for later better LSM interaction.
- xfrm: Remove inner/outer modes from input/output path. These are
not needed anymore.
- WiFi:
- reduced neighbor report (RNR) handling for AP mode
- HW timestamping support
- support for randomized auth/deauth TA for PASN privacy
- per-link debugfs for multi-link
- TC offload support for mac80211 drivers
- mac80211 mesh fast-xmit and fast-rx support
- enable Wi-Fi 7 (EHT) mesh support
Netfilter
---------
- Add nf_tables 'brouting' support, to force a packet to be routed
instead of being bridged.
- Update bridge netfilter and ovs conntrack helpers to handle
IPv6 Jumbo packets properly, i.e. fetch the packet length
from hop-by-hop extension header. This is needed for BIT TCP
support.
- The iptables 32bit compat interface isn't compiled in by default
anymore.
- Move ip(6)tables builtin icmp matches to the udptcp one.
This has the advantage that icmp/icmpv6 match doesn't load the
iptables/ip6tables modules anymore when iptables-nft is used.
- Extended netlink error report for netdevice in flowtables and
netdev/chains. Allow for incrementally add/delete devices to netdev
basechain. Allow to create netdev chain without device.
Driver API
----------
- Remove redundant Device Control Error Reporting Enable, as PCI core
has already error reporting enabled at enumeration time.
- Move Multicast DB netlink handlers to core, allowing devices other
then bridge to use them.
- Allow the page_pool to directly recycle the pages from safely
localized NAPI.
- Implement lockless TX queue stop/wake combo macros, allowing for
further code de-duplication and sanitization.
- Add YNL support for user headers and struct attrs.
- Add partial YNL specification for devlink.
- Add partial YNL specification for ethtool.
- Add tc-mqprio and tc-taprio support for preemptible traffic classes.
- Add tx push buf len param to ethtool, specifies the maximum number
of bytes of a transmitted packet a driver can push directly to the
underlying device.
- Add basic LED support for switch/phy.
- Add NAPI documentation, stop relaying on external links.
- Convert dsa_master_ioctl() to netdev notifier. This is a preparatory
work to make the hardware timestamping layer selectable by user
space.
- Add transceiver support and improve the error messages for CAN-FD
controllers.
New hardware / drivers
----------------------
- Ethernet:
- AMD/Pensando core device support
- MediaTek MT7981 SoC
- MediaTek MT7988 SoC
- Broadcom BCM53134 embedded switch
- Texas Instruments CPSW9G ethernet switch
- Qualcomm EMAC3 DWMAC ethernet
- StarFive JH7110 SoC
- NXP CBTX ethernet PHY
- WiFi:
- Apple M1 Pro/Max devices
- RealTek rtl8710bu/rtl8188gu
- RealTek rtl8822bs, rtl8822cs and rtl8821cs SDIO chipset
- Bluetooth:
- Realtek RTL8821CS, RTL8851B, RTL8852BS
- Mediatek MT7663, MT7922
- NXP w8997
- Actions Semi ATS2851
- QTI WCN6855
- Marvell 88W8997
- Can:
- STMicroelectronics bxcan stm32f429
Drivers
-------
- Ethernet NICs:
- Intel (1G, icg):
- add tracking and reporting of QBV config errors.
- add support for configuring max SDU for each Tx queue.
- Intel (100G, ice):
- refactor mailbox overflow detection to support Scalable IOV
- GNSS interface optimization
- Intel (i40e):
- support XDP multi-buffer
- nVidia/Mellanox:
- add the support for linux bridge multicast offload
- enable TC offload for egress and engress MACVLAN over bond
- add support for VxLAN GBP encap/decap flows offload
- extend packet offload to fully support libreswan
- support tunnel mode in mlx5 IPsec packet offload
- extend XDP multi-buffer support
- support MACsec VLAN offload
- add support for dynamic msix vectors allocation
- drop RX page_cache and fully use page_pool
- implement thermal zone to report NIC temperature
- Netronome/Corigine:
- add support for multi-zone conntrack offload
- Solarflare/Xilinx:
- support offloading TC VLAN push/pop actions to the MAE
- support TC decap rules
- support unicast PTP
- Other NICs:
- Broadcom (bnxt): enforce software based freq adjustments only
on shared PHC NIC
- RealTek (r8169): refactor to addess ASPM issues during NAPI poll.
- Micrel (lan8841): add support for PTP_PF_PEROUT
- Cadence (macb): enable PTP unicast
- Engleder (tsnep): add XDP socket zero-copy support
- virtio-net: implement exact header length guest feature
- veth: add page_pool support for page recycling
- vxlan: add MDB data path support
- gve: add XDP support for GQI-QPL format
- geneve: accept every ethertype
- macvlan: allow some packets to bypass broadcast queue
- mana: add support for jumbo frame
- Ethernet high-speed switches:
- Microchip (sparx5): Add support for TC flower templates.
- Ethernet embedded switches:
- Broadcom (b54):
- configure 6318 and 63268 RGMII ports
- Marvell (mv88e6xxx):
- faster C45 bus scan
- Microchip:
- lan966x:
- add support for IS1 VCAP
- better TX/RX from/to CPU performances
- ksz9477: add ETS Qdisc support
- ksz8: enhance static MAC table operations and error handling
- sama7g5: add PTP capability
- NXP (ocelot):
- add support for external ports
- add support for preemptible traffic classes
- Texas Instruments:
- add CPSWxG SGMII support for J7200 and J721E
- Intel WiFi (iwlwifi):
- preparation for Wi-Fi 7 EHT and multi-link support
- EHT (Wi-Fi 7) sniffer support
- hardware timestamping support for some devices/firwmares
- TX beacon protection on newer hardware
- Qualcomm 802.11ax WiFi (ath11k):
- MU-MIMO parameters support
- ack signal support for management packets
- RealTek WiFi (rtw88):
- SDIO bus support
- better support for some SDIO devices
(e.g. MAC address from efuse)
- RealTek WiFi (rtw89):
- HW scan support for 8852b
- better support for 6 GHz scanning
- support for various newer firmware APIs
- framework firmware backwards compatibility
- MediaTek WiFi (mt76):
- P2P support
- mesh A-MSDU support
- EHT (Wi-Fi 7) support
- coredump support
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=ITVa
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"Core:
- Introduce a config option to tweak MAX_SKB_FRAGS. Increasing the
default value allows for better BIG TCP performances
- Reduce compound page head access for zero-copy data transfers
- RPS/RFS improvements, avoiding unneeded NET_RX_SOFTIRQ when
possible
- Threaded NAPI improvements, adding defer skb free support and
unneeded softirq avoidance
- Address dst_entry reference count scalability issues, via false
sharing avoidance and optimize refcount tracking
- Add lockless accesses annotation to sk_err[_soft]
- Optimize again the skb struct layout
- Extends the skb drop reasons to make it usable by multiple
subsystems
- Better const qualifier awareness for socket casts
BPF:
- Add skb and XDP typed dynptrs which allow BPF programs for more
ergonomic and less brittle iteration through data and
variable-sized accesses
- Add a new BPF netfilter program type and minimal support to hook
BPF programs to netfilter hooks such as prerouting or forward
- Add more precise memory usage reporting for all BPF map types
- Adds support for using {FOU,GUE} encap with an ipip device
operating in collect_md mode and add a set of BPF kfuncs for
controlling encap params
- Allow BPF programs to detect at load time whether a particular
kfunc exists or not, and also add support for this in light
skeleton
- Bigger batch of BPF verifier improvements to prepare for upcoming
BPF open-coded iterators allowing for less restrictive looping
capabilities
- Rework RCU enforcement in the verifier, add kptr_rcu and enforce
BPF programs to NULL-check before passing such pointers into kfunc
- Add support for kptrs in percpu hashmaps, percpu LRU hashmaps and
in local storage maps
- Enable RCU semantics for task BPF kptrs and allow referenced kptr
tasks to be stored in BPF maps
- Add support for refcounted local kptrs to the verifier for allowing
shared ownership, useful for adding a node to both the BPF list and
rbtree
- Add BPF verifier support for ST instructions in
convert_ctx_access() which will help new -mcpu=v4 clang flag to
start emitting them
- Add ARM32 USDT support to libbpf
- Improve bpftool's visual program dump which produces the control
flow graph in a DOT format by adding C source inline annotations
Protocols:
- IPv4: Allow adding to IPv4 address a 'protocol' tag. Such value
indicates the provenance of the IP address
- IPv6: optimize route lookup, dropping unneeded R/W lock acquisition
- Add the handshake upcall mechanism, allowing the user-space to
implement generic TLS handshake on kernel's behalf
- Bridge: support per-{Port, VLAN} neighbor suppression, increasing
resilience to nodes failures
- SCTP: add support for Fair Capacity and Weighted Fair Queueing
schedulers
- MPTCP: delay first subflow allocation up to its first usage. This
will allow for later better LSM interaction
- xfrm: Remove inner/outer modes from input/output path. These are
not needed anymore
- WiFi:
- reduced neighbor report (RNR) handling for AP mode
- HW timestamping support
- support for randomized auth/deauth TA for PASN privacy
- per-link debugfs for multi-link
- TC offload support for mac80211 drivers
- mac80211 mesh fast-xmit and fast-rx support
- enable Wi-Fi 7 (EHT) mesh support
Netfilter:
- Add nf_tables 'brouting' support, to force a packet to be routed
instead of being bridged
- Update bridge netfilter and ovs conntrack helpers to handle IPv6
Jumbo packets properly, i.e. fetch the packet length from
hop-by-hop extension header. This is needed for BIT TCP support
- The iptables 32bit compat interface isn't compiled in by default
anymore
- Move ip(6)tables builtin icmp matches to the udptcp one. This has
the advantage that icmp/icmpv6 match doesn't load the
iptables/ip6tables modules anymore when iptables-nft is used
- Extended netlink error report for netdevice in flowtables and
netdev/chains. Allow for incrementally add/delete devices to netdev
basechain. Allow to create netdev chain without device
Driver API:
- Remove redundant Device Control Error Reporting Enable, as PCI core
has already error reporting enabled at enumeration time
- Move Multicast DB netlink handlers to core, allowing devices other
then bridge to use them
- Allow the page_pool to directly recycle the pages from safely
localized NAPI
- Implement lockless TX queue stop/wake combo macros, allowing for
further code de-duplication and sanitization
- Add YNL support for user headers and struct attrs
- Add partial YNL specification for devlink
- Add partial YNL specification for ethtool
- Add tc-mqprio and tc-taprio support for preemptible traffic classes
- Add tx push buf len param to ethtool, specifies the maximum number
of bytes of a transmitted packet a driver can push directly to the
underlying device
- Add basic LED support for switch/phy
- Add NAPI documentation, stop relaying on external links
- Convert dsa_master_ioctl() to netdev notifier. This is a
preparatory work to make the hardware timestamping layer selectable
by user space
- Add transceiver support and improve the error messages for CAN-FD
controllers
New hardware / drivers:
- Ethernet:
- AMD/Pensando core device support
- MediaTek MT7981 SoC
- MediaTek MT7988 SoC
- Broadcom BCM53134 embedded switch
- Texas Instruments CPSW9G ethernet switch
- Qualcomm EMAC3 DWMAC ethernet
- StarFive JH7110 SoC
- NXP CBTX ethernet PHY
- WiFi:
- Apple M1 Pro/Max devices
- RealTek rtl8710bu/rtl8188gu
- RealTek rtl8822bs, rtl8822cs and rtl8821cs SDIO chipset
- Bluetooth:
- Realtek RTL8821CS, RTL8851B, RTL8852BS
- Mediatek MT7663, MT7922
- NXP w8997
- Actions Semi ATS2851
- QTI WCN6855
- Marvell 88W8997
- Can:
- STMicroelectronics bxcan stm32f429
Drivers:
- Ethernet NICs:
- Intel (1G, icg):
- add tracking and reporting of QBV config errors
- add support for configuring max SDU for each Tx queue
- Intel (100G, ice):
- refactor mailbox overflow detection to support Scalable IOV
- GNSS interface optimization
- Intel (i40e):
- support XDP multi-buffer
- nVidia/Mellanox:
- add the support for linux bridge multicast offload
- enable TC offload for egress and engress MACVLAN over bond
- add support for VxLAN GBP encap/decap flows offload
- extend packet offload to fully support libreswan
- support tunnel mode in mlx5 IPsec packet offload
- extend XDP multi-buffer support
- support MACsec VLAN offload
- add support for dynamic msix vectors allocation
- drop RX page_cache and fully use page_pool
- implement thermal zone to report NIC temperature
- Netronome/Corigine:
- add support for multi-zone conntrack offload
- Solarflare/Xilinx:
- support offloading TC VLAN push/pop actions to the MAE
- support TC decap rules
- support unicast PTP
- Other NICs:
- Broadcom (bnxt): enforce software based freq adjustments only on
shared PHC NIC
- RealTek (r8169): refactor to addess ASPM issues during NAPI poll
- Micrel (lan8841): add support for PTP_PF_PEROUT
- Cadence (macb): enable PTP unicast
- Engleder (tsnep): add XDP socket zero-copy support
- virtio-net: implement exact header length guest feature
- veth: add page_pool support for page recycling
- vxlan: add MDB data path support
- gve: add XDP support for GQI-QPL format
- geneve: accept every ethertype
- macvlan: allow some packets to bypass broadcast queue
- mana: add support for jumbo frame
- Ethernet high-speed switches:
- Microchip (sparx5): Add support for TC flower templates
- Ethernet embedded switches:
- Broadcom (b54):
- configure 6318 and 63268 RGMII ports
- Marvell (mv88e6xxx):
- faster C45 bus scan
- Microchip:
- lan966x:
- add support for IS1 VCAP
- better TX/RX from/to CPU performances
- ksz9477: add ETS Qdisc support
- ksz8: enhance static MAC table operations and error handling
- sama7g5: add PTP capability
- NXP (ocelot):
- add support for external ports
- add support for preemptible traffic classes
- Texas Instruments:
- add CPSWxG SGMII support for J7200 and J721E
- Intel WiFi (iwlwifi):
- preparation for Wi-Fi 7 EHT and multi-link support
- EHT (Wi-Fi 7) sniffer support
- hardware timestamping support for some devices/firwmares
- TX beacon protection on newer hardware
- Qualcomm 802.11ax WiFi (ath11k):
- MU-MIMO parameters support
- ack signal support for management packets
- RealTek WiFi (rtw88):
- SDIO bus support
- better support for some SDIO devices (e.g. MAC address from
efuse)
- RealTek WiFi (rtw89):
- HW scan support for 8852b
- better support for 6 GHz scanning
- support for various newer firmware APIs
- framework firmware backwards compatibility
- MediaTek WiFi (mt76):
- P2P support
- mesh A-MSDU support
- EHT (Wi-Fi 7) support
- coredump support"
* tag 'net-next-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2078 commits)
net: phy: hide the PHYLIB_LEDS knob
net: phy: marvell-88x2222: remove unnecessary (void*) conversions
tcp/udp: Fix memleaks of sk and zerocopy skbs with TX timestamp.
net: amd: Fix link leak when verifying config failed
net: phy: marvell: Fix inconsistent indenting in led_blink_set
lan966x: Don't use xdp_frame when action is XDP_TX
tsnep: Add XDP socket zero-copy TX support
tsnep: Add XDP socket zero-copy RX support
tsnep: Move skb receive action to separate function
tsnep: Add functions for queue enable/disable
tsnep: Rework TX/RX queue initialization
tsnep: Replace modulo operation with mask
net: phy: dp83867: Add led_brightness_set support
net: phy: Fix reading LED reg property
drivers: nfc: nfcsim: remove return value check of `dev_dir`
net: phy: dp83867: Remove unnecessary (void*) conversions
net: ethtool: coalesce: try to make user settings stick twice
net: mana: Check if netdev/napi_alloc_frag returns single page
net: mana: Rename mana_refill_rxoob and remove some empty lines
net: veth: add page_pool stats
...
-----BEGIN PGP SIGNATURE-----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=W1Zb
-----END PGP SIGNATURE-----
Merge tag 'for-6.4/block-2023-04-21' of git://git.kernel.dk/linux
Pull block updates from Jens Axboe:
- drbd patches, bringing us closer to unifying the out-of-tree version
and the in tree one (Andreas, Christoph)
- support for auto-quiesce for the s390 dasd driver (Stefan)
- MD pull request via Song:
- md/bitmap: Optimal last page size (Jon Derrick)
- Various raid10 fixes (Yu Kuai, Li Nan)
- md: add error_handlers for raid0 and linear (Mariusz Tkaczyk)
- NVMe pull request via Christoph:
- Drop redundant pci_enable_pcie_error_reporting (Bjorn Helgaas)
- Validate nvmet module parameters (Chaitanya Kulkarni)
- Fence TCP socket on receive error (Chris Leech)
- Fix async event trace event (Keith Busch)
- Minor cleanups (Chaitanya Kulkarni, zhenwei pi)
- Fix and cleanup nvmet Identify handling (Damien Le Moal,
Christoph Hellwig)
- Fix double blk_mq_complete_request race in the timeout handler
(Lei Yin)
- Fix irq locking in nvme-fcloop (Ming Lei)
- Remove queue mapping helper for rdma devices (Sagi Grimberg)
- use structured request attribute checks for nbd (Jakub)
- fix blk-crypto race conditions between keyslot management (Eric)
- add sed-opal support for reading read locking range attributes
(Ondrej)
- make fault injection configurable for null_blk (Akinobu)
- clean up the request insertion API (Christoph)
- clean up the queue running API (Christoph)
- blkg config helper cleanups (Tejun)
- lazy init support for blk-iolatency (Tejun)
- various fixes and tweaks to ublk (Ming)
- remove hybrid polling. It hasn't really been useful since we got
async polled IO support, and these days we don't support sync polled
IO at all (Keith)
- misc fixes, cleanups, improvements (Zhong, Ondrej, Colin, Chengming,
Chaitanya, me)
* tag 'for-6.4/block-2023-04-21' of git://git.kernel.dk/linux: (118 commits)
nbd: fix incomplete validation of ioctl arg
ublk: don't return 0 in case of any failure
sed-opal: geometry feature reporting command
null_blk: Always check queue mode setting from configfs
block: ublk: switch to ioctl command encoding
blk-mq: fix the blk_mq_add_to_requeue_list call in blk_kick_flush
block, bfq: Fix division by zero error on zero wsum
fault-inject: fix build error when FAULT_INJECTION_CONFIGFS=y and CONFIGFS_FS=m
block: store bdev->bd_disk->fops->submit_bio state in bdev
block: re-arrange the struct block_device fields for better layout
md/raid5: remove unused working_disks variable
md/raid10: don't call bio_start_io_acct twice for bio which experienced read error
md/raid10: fix memleak of md thread
md/raid10: fix memleak for 'conf->bio_split'
md/raid10: fix leak of 'r10bio->remaining' for recovery
md/raid10: don't BUG_ON() in raise_barrier()
md: fix soft lockup in status_resync
md: add error_handlers for raid0 and linear
md: Use optimal I/O size for last bitmap page
md: Fix types in sb writer
...
-----BEGIN PGP SIGNATURE-----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=Erfk
-----END PGP SIGNATURE-----
Merge tag 'for-6.4/io_uring-2023-04-21' of git://git.kernel.dk/linux
Pull io_uring updates from Jens Axboe:
- Cleanup of the io-wq per-node mapping, notably getting rid of it so
we just have a single io_wq entry per ring (Breno)
- Followup to the above, move accounting to io_wq as well and
completely drop struct io_wqe (Gabriel)
- Enable KASAN for the internal io_uring caches (Breno)
- Add support for multishot timeouts. Some applications use timeouts to
wake someone waiting on completion entries, and this makes it a bit
easier to just have a recurring timer rather than needing to rearm it
every time (David)
- Support archs that have shared cache coloring between userspace and
the kernel, and hence have strict address requirements for mmap'ing
the ring into userspace. This should only be parisc/hppa. (Helge, me)
- XFS has supported O_DIRECT writes without needing to lock the inode
exclusively for a long time, and ext4 now supports it as well. This
is true for the common cases of not extending the file size. Flag the
fs as having that feature, and utilize that to avoid serializing
those writes in io_uring (me)
- Enable completion batching for uring commands (me)
- Revert patch adding io_uring restriction to what can be GUP mapped or
not. This does not belong in io_uring, as io_uring isn't really
special in this regard. Since this is also getting in the way of
cleanups and improvements to the GUP code, get rid of if (me)
- A few series greatly reducing the complexity of registered resources,
like buffers or files. Not only does this clean up the code a lot,
the simplified code is also a LOT more efficient (Pavel)
- Series optimizing how we wait for events and run task_work related to
it (Pavel)
- Fixes for file/buffer unregistration with DEFER_TASKRUN (Pavel)
- Misc cleanups and improvements (Pavel, me)
* tag 'for-6.4/io_uring-2023-04-21' of git://git.kernel.dk/linux: (71 commits)
Revert "io_uring/rsrc: disallow multi-source reg buffers"
io_uring: add support for multishot timeouts
io_uring/rsrc: disassociate nodes and rsrc_data
io_uring/rsrc: devirtualise rsrc put callbacks
io_uring/rsrc: pass node to io_rsrc_put_work()
io_uring/rsrc: inline io_rsrc_put_work()
io_uring/rsrc: add empty flag in rsrc_node
io_uring/rsrc: merge nodes and io_rsrc_put
io_uring/rsrc: infer node from ctx on io_queue_rsrc_removal
io_uring/rsrc: remove unused io_rsrc_node::llist
io_uring/rsrc: refactor io_queue_rsrc_removal
io_uring/rsrc: simplify single file node switching
io_uring/rsrc: clean up __io_sqe_buffers_update()
io_uring/rsrc: inline switch_start fast path
io_uring/rsrc: remove rsrc_data refs
io_uring/rsrc: fix DEFER_TASKRUN rsrc quiesce
io_uring/rsrc: use wq for quiescing
io_uring/rsrc: refactor io_rsrc_ref_quiesce
io_uring/rsrc: remove io_rsrc_node::done
io_uring/rsrc: use nospec'ed indexes
...
-----BEGIN PGP SIGNATURE-----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=EaE9
-----END PGP SIGNATURE-----
Merge tag 'iter-ubuf.2-2023-04-21' of git://git.kernel.dk/linux
Pull ITER_UBUF updates from Jens Axboe:
"This turns singe vector imports into ITER_UBUF, rather than
ITER_IOVEC.
The former is more trivial to iterate and advance, and hence a bit
more efficient. From some very unscientific testing, ~60% of all iovec
imports are single vector"
* tag 'iter-ubuf.2-2023-04-21' of git://git.kernel.dk/linux:
iov_iter: Mark copy_compat_iovec_from_user() noinline
iov_iter: import single vector iovecs as ITER_UBUF
iov_iter: convert import_single_range() to ITER_UBUF
iov_iter: overlay struct iovec and ubuf/len
iov_iter: set nr_segs = 1 for ITER_UBUF
iov_iter: remove iov_iter_iovec()
iov_iter: add iter_iov_addr() and iter_iov_len() helpers
ALSA: pcm: check for user backed iterator, not specific iterator type
IB/qib: check for user backed iterator, not specific iterator type
IB/hfi1: check for user backed iterator, not specific iterator type
iov_iter: add iter_iovec() helper
block: ensure bio_alloc_map_data() deals with ITER_UBUF correctly
This reverts commit edd4782696.
There's really no specific need to disallow multiple sources of buffers,
and io_uring really should not be mandating this by itself. We should
be able to solely rely on GUP making these decisions.
As this also stands in the way of a cleanup where io_uring is the odd
one out, kill it.
Link: https://lore.kernel.org/all/61ded378-51a8-1dcb-b631-fda1903248a9@gmail.com/
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A multishot timeout submission will repeatedly generate completions with
the IORING_CQE_F_MORE cflag set. Depending on the value of the `off'
field in the submission, these timeouts can either repeat indefinitely
until cancelled (`off' = 0) or for a fixed number of times (`off' > 0).
Only noseq timeouts (i.e. not dependent on the number of I/O
completions) are supported.
An indefinite timer will be cancelled if the CQ ever overflows.
Signed-off-by: David Wei <davidhwei@meta.com>
Link: https://lore.kernel.org/r/20230418225817.1905027-1-davidhwei@meta.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
struct io_rsrc_node carries a number of resources represented by struct
io_rsrc_put. That was handy before for sync overhead ammortisation, but
all complexity is gone and nodes are simple and lightweight. Let's
allocate a separate node for each resource.
Nodes and io_rsrc_put and not much different in size, and former are
cached, so node allocation should work better. That also removes some
overhead for nested iteration in io_rsrc_node_ref_zero() /
__io_rsrc_put_work().
Another reason for the patch is that it greatly reduces complexity
by moving io_rsrc_node_switch[_start]() inside io_queue_rsrc_removal(),
so users don't have to care about it.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/c7d3a45b30cc14cd93700a710dd112edc703db98.1681822823.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For io_rsrc_ref_quiesce() to progress it should execute all task_work
items, including deferred ones. However, currently nobody would wake us,
and so let's set ctx->cq_wait_nr, so io_req_local_work_add() would wake
us up.
Fixes: c0e0d6ba25 ("io_uring: add IORING_SETUP_DEFER_TASKRUN")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/f1a90d1bc5ebf096475b018fed52e54f3b89d4af.1681395792.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Replace completions with waitqueues for rsrc data quiesce, the main
wakeup condition is when data refs hit zero. Note that data refs are
only changes under ->uring_lock, so we prepare before mutex_unlock()
reacquire it after taking the lock back. This change will be needed
in the next patch.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/1d0dbc74b3b4fd67c8f01819e680c5e0da252956.1681395792.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add a constant IO_NOTIF_UBUF_FLAGS for struct ubuf_info flags that
notifications use. That should minimise merge conflicts for planned
changes touching both io_uring and net at the same time.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
iQJEBAABCAAuFiEEwPw5LcreJtl1+l5K99NY+ylx4KYFAmQ6HP4QHGF4Ym9lQGtl
cm5lbC5kawAKCRD301j7KXHgpiuxD/wMRoH/NfgJy1QsnXaelZihWeKx7ywsFiwd
0EXmNClOae0Lwvn6wmIYYsBCIeK7Np0WAhAQzpfxPBPr8twnV0ZIpSMIBUjFyt01
u0LEeYA/Sjy7WRKAd2SFHiEREM45Vxvp3suaw1gGNhanfL5FfnwmGO+GTY9tIAzz
P5QEhA7kOho/rfx/4L0gze1K2hGFkd1C8ezJq5KRZd2EMUT45UIhHNoOwQaM7DHQ
GWRoVCFREMdA+xyOZ+4xTWXrd3R3ptE02b5vIwCw+y4hNxQHUaLWlu427zlL4ozb
QR7i6y1wtVDiTfBiuBY36qX6Ne84aAsNWqaRvwmcCl0VfGsQOpHtjs4eQWYVLeUB
3+7tUgGtXaBWMB9hCoOsnuQq2m7vuV56ECgufvpKUaoz9KUuAaWo3MgB157ORME3
+Va9R7HhjNtUpP1tPS5w6ljTRWngVcp8rdwWt+2mrlsmFQlqjppl5fOBTPqIA6+k
WVj+0S9pJXHAEveFeJ3SqyjQfDuPw1o9mxinczNle/gKaFqjX2tQfmQgNATgiIDD
kNSW3Bccw7LWKTScklzMtyowMLoonrfveqqH3QKmVm5K+zFEULWfZqFNlVoqGrYi
qF4pCEIPF/FxrpEvQP1Bp04ZH4qJpGrjuhhJke4kjB9DGRDv6T6m8EzKWkWuFlDH
i18gYxJG/w==
=pzRD
-----END PGP SIGNATURE-----
Merge tag 'io_uring-6.3-2023-04-14' of git://git.kernel.dk/linux
Pull io_uring fix from Jens Axboe:
"Just a small tweak to when task_work needs redirection, marked for
stable as well"
* tag 'io_uring-6.3-2023-04-14' of git://git.kernel.dk/linux:
io_uring: complete request via task work in case of DEFER_TASKRUN
So far io_req_complete_post() only covers DEFER_TASKRUN by completing
request via task work when the request is completed from IOWQ.
However, uring command could be completed from any context, and if io
uring is setup with DEFER_TASKRUN, the command is required to be
completed from current context, otherwise wait on IORING_ENTER_GETEVENTS
can't be wakeup, and may hang forever.
The issue can be observed on removing ublk device, but turns out it is
one generic issue for uring command & DEFER_TASKRUN, so solve it in
io_uring core code.
Fixes: e6aeb2721d ("io_uring: complete all requests in task context")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-block/b3fc9991-4c53-9218-a8cc-5b4dd3952108@kernel.dk/
Reported-by: Jens Axboe <axboe@kernel.dk>
Cc: Kanchan Joshi <joshi.k@samsung.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We use io_rsrc_node_switch() coupled with io_rsrc_node_switch_start()
for a bunch of cases including initialising ctx->rsrc_node, i.e. by
passing NULL instead of rsrc_data. Leave it to only deal with actual
node changing.
For that, first remove it from io_uring_create() and add a function
allocating the first node. Then also remove all calls to
io_rsrc_node_switch() from files/buffers register as we already have a
node installed and it does essentially nothing.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/d146fe306ff98b1a5a60c997c252534f03d423d7.1681210788.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The kernel test robot complains about __io_remove_buffers().
io_uring/kbuf.c:221 __io_remove_buffers() warn: variable dereferenced
before check 'bl->buf_ring' (see line 219)
That check is not needed as ->buf_ring will always be set, so we can
remove it and so silence the warning.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/9a632bbf749d9d911e605255652ce08d18e7d2c6.1681210788.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
io_uring/io_uring.c:432 io_prep_async_work() error: we previously
assumed 'req->file' could be null (see line 425).
Even though it's a false positive as there will not be REQ_F_ISREG set
without a file, let's add a simple check to make the kernel test robot
happy. We don't care about performance here, but assumingly it'll be
optimised out by the compiler.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/a6cfbe92c74b789c0b4f046f7f98d19b1ca2e5b7.1681210788.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We know now what the completion context is for the uring_cmd completion
handling, so use that to have io_req_task_complete() decide what the
best way to complete the request is. This allows batching of the posted
completions if we have multiple pending, rather than always doing them
one-by-one.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=32lQ
-----END PGP SIGNATURE-----
Merge tag 'io_uring-6.3-2023-04-06' of git://git.kernel.dk/linux
Pull io_uring fixes from Jens Axboe:
"Just two minor fixes for provided buffers - one where we could
potentially leak a buffer, and one where the returned values was
off-by-one in some cases"
* tag 'io_uring-6.3-2023-04-06' of git://git.kernel.dk/linux:
io_uring: fix memory leak when removing provided buffers
io_uring: fix return value when removing provided buffers
Chains of memory accesses are never good for performance.
The req->task->io_uring->in_cancel in io_req_local_work_add() is there
so that when a task is exiting via io_uring_try_cancel_requests() and
starts waiting for completions, it gets woken up by every new task_work
item queued.
Do a little trick by announcing waiting in io_uring_try_cancel_requests(),
making io_req_local_work_add() wake us up. We also need to check for
deferred tw items after prepare_to_wait(TASK_INTERRUPTIBLE);
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/fb11597e9bbcb365901824f8c5c2cf0d6ee100d0.1680782017.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Every task_work will try to wake the task to be executed, which causes
excessive scheduling and additional overhead. For some tw it's
justified, but others won't do much but post a single CQE.
When a task waits for multiple cqes, every such task_work will wake it
up. Instead, the task may give a hint about how many cqes it waits for,
io_req_local_work_add() will compare against it and skip wake ups
if #cqes + #tw is not enough to satisfy the waiting condition. Task_work
that uses the optimisation should be simple enough and never post more
than one CQE. It's also ignored for non DEFER_TASKRUN rings.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/d2b77e99d1e86624d8a69f7037d764b739dcd225.1680782017.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We currently pin the ctx for io_req_local_work_add() with
percpu_ref_get/put, which implies two rcu_read_lock/unlock pairs and some
extra overhead on top in the fast path. Replace it with a pure rcu read
and let io_ring_exit_work() synchronise against it.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/cbdfcb6b232627f30e9e50ef91f13c4f05910247.1680782017.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Rather than check this in the fast path issue, it makes more sense to
just assign the copy of the data when we're setting it up anyway. This
makes the code a bit cleaner, and removes the need for this check in
the issue path.
Reviewed-by: Gabriel Krisman Bertazi <krisman@suse.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
struct delayed_work rsrc_put_work was previously used to offload node
freeing because io_rsrc_node_ref_zero() was previously called by RCU in
the IRQ context. Now, as percpu refcounting is gone, we can do it
eagerly at the spot without pushing it to a worker.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/13fb1aac1e8d068ad8fd4a0c6d0d157ab61b90c0.1680576071.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Every io_rsrc_node keeps a list of items to put, and all entries are
kmalloc()'ed. However, it's quite often to queue up only one entry per
node, so let's add an inline entry there to avoid extra allocations.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/c482c1c652c45c85ac52e67c974bc758a50fed5f.1680576071.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We have too many "rsrc" around which makes the name of struct
io_rsrc_node::rsrc_list confusing. The field is responsible for keeping
a list of files or buffers, so call it item_list and add comments
around.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/3e34d4dfc1fdbb6b520f904ee6187c2ccf680efe.1680576071.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We use ->rsrc_ref_lock spinlock to protect ->rsrc_ref_list in
io_rsrc_node_ref_zero(). Now we removed pcpu refcounting, which means
io_rsrc_node_ref_zero() is not executed from the irq context as an RCU
callback anymore, and we also put it under ->uring_lock.
io_rsrc_node_switch(), which queues up nodes into the list, is also
protected by ->uring_lock, so we can safely get rid of ->rsrc_ref_lock.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/6b60af883c263551190b526a55ff2c9d5ae07141.1680576071.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently, for nodes we have an atomic counter and some cached
(non-atomic) refs protected by uring_lock. Let's put all ref
manipulations under uring_lock and get rid of the atomic part.
It's free as in all cases we care about we already hold the lock.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/25b142feed7d831008257d90c8b17c0115d4fc15.1680576071.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
io_free_req() is not often used but nevertheless problematic as there is
no way to know the current context, it may be used from the submission
path or even by an irq handler. Push it to a fresh context using
task_work.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/3a92fe80bb068757e51aaa0b105cfbe8f5dfee9e.1680576071.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We cache refs of the current node (i.e. ctx->rsrc_node) in
ctx->rsrc_cached_refs. We'll be moving away from atomics, so move the
cached refs in struct io_rsrc_node for now. It's a prep patch and
shouldn't change anything in practise.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/9edc3669c1d71b06c2dca78b2b2b8bb9292738b9.1680576071.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
One problem with the current rsrc infra is that often updates will
generates lots of rsrc nodes, each carry pcpu refs. That takes quite a
lot of memory, especially if there is a stall, and takes lots of CPU
cycles. Only pcpu allocations takes >50 of CPU with a naive benchmark
updating files in a loop.
Replace pcpu refs with normal refcounting. There is already a hot path
avoiding atomics / refs, but following patches will further improve it.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/e9ed8a9457b331a26555ff9443afc64cdaab7247.1680576071.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We already do this manually for the !SQPOLL case, do it in general and
we can also dump the ugly min3() in io_submit_sqes().
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It has nothing to do with the SQE at this point, it's a request
submission. While in there, get rid of the 'force_nonblock' argument
which is also dead, as we only pass in true.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For task works we're passing around a bool pointer for whether the
current ring is locked or not, let's wrap it in a structure, that
will make it more opaque preventing abuse and will also help us
to pass more info in the future if needed.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/1ecec9483d58696e248d1bfd52cf62b04442df1d.1679931367.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Before cond_resched()'ing in handle_tw_list() we also drop the current
ring context, and so the next loop iteration will need to pick/pin a new
context and do trylock.
The chunk removed by this patch was intended to be an optimisation
covering exactly this case, i.e. retaking the lock after reschedule, but
in reality it's skipped for the first iteration after resched as
described and will keep hammering the lock if it's contended.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/1ecec9483d58696e248d1bfd52cf62b04442df1d.1679931367.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since the move to PF_IO_WORKER, we don't juggle memory context manually
anymore. Remove that outdated part of the comment for __io_worker_idle().
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since commit 0654b05e7e65 ("io_uring: One wqe per wq"), we have just a
single io_wqe instance embedded per io_wq. Drop the extra structure in
favor of accessing struct io_wq directly, cleaning up quite a bit of
dereferences and backpointers.
No functional changes intended. Tested with liburing's testsuite
and mmtests performance microbenchmarks. I didn't observe any
performance regressions.
Signed-off-by: Gabriel Krisman Bertazi <krisman@suse.de>
Link: https://lore.kernel.org/r/20230322011628.23359-2-krisman@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since we now have a single io_wqe per io_wq instead of per-node, and in
preparation to its removal, move the accounting into the parent
structure.
Signed-off-by: Gabriel Krisman Bertazi <krisman@suse.de>
Link: https://lore.kernel.org/r/20230322011628.23359-2-krisman@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
On at least parisc, we have strict requirements on how we virtually map
an address that is shared between the application and the kernel. On
these platforms, IOU_PBUF_RING_MMAP should be used when setting up a
shared ring buffer for provided buffers. If the application is mapping
these pages and asking the kernel to pin+map them as well, then we have
no control over what virtual address we get in the kernel.
For that case, do a sanity check if SHM_COLOUR is defined, and disallow
the mapping request. The application must fall back to using
IOU_PBUF_RING_MMAP for this case, and liburing will do that transparently
with the set of helpers that it has.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add support for KASAN in the alloc_caches (apoll and netmsg_cache).
Thus, if something touches the unused caches, it will raise a KASAN
warning/exception.
It poisons the object when the object is put to the cache, and unpoisons
it when the object is gotten or freed.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Gabriel Krisman Bertazi <krisman@suse.de>
Link: https://lore.kernel.org/r/20230223164353.2839177-2-leitao@debian.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Having cache entries linked using the hlist format brings no benefit, and
also requires an unnecessary extra pointer address per cache entry.
Use the internal io_wq_work_node single-linked list for the internal
alloc caches (async_msghdr and async_poll)
This is required to be able to use KASAN on cache entries, since we do
not need to touch unused (and poisoned) cache entries when adding more
entries to the list.
Suggested-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20230223164353.2839177-2-leitao@debian.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Right now io_wq allocates one io_wqe per NUMA node. As io_wq is now
bound to a task, the task basically uses only the NUMA local io_wqe, and
almost never changes NUMA nodes, thus, the other wqes are mostly
unused.
Allocate just one io_wqe embedded into io_wq, and uses all possible cpus
(cpu_possible_mask) in the io_wqe->cpumask.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20230310201107.4020580-1-leitao@debian.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The ring mapped provided buffer rings rely on the application allocating
the memory for the ring, and then the kernel will map it. This generally
works fine, but runs into issues on some architectures where we need
to be able to ensure that the kernel and application virtual address for
the ring play nicely together. This at least impacts architectures that
set SHM_COLOUR, but potentially also anyone setting SHMLBA.
To use this variant of ring provided buffers, the application need not
allocate any memory for the ring. Instead the kernel will do so, and
the allocation must subsequently call mmap(2) on the ring with the
offset set to:
IORING_OFF_PBUF_RING | (bgid << IORING_OFF_PBUF_SHIFT)
to get a virtual address for the buffer ring. Normally the application
would allocate a suitable piece of memory (and correctly aligned) and
simply pass that in via io_uring_buf_reg.ring_addr and the kernel would
map it.
Outside of the setup differences, the kernel allocate + user mapped
provided buffer ring works exactly the same.
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In preparation for allowing flags to be set for registration, rename
the padding and use it for that.
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Rather than rely on checking buffer_list->buf_pages or ->buf_nr_pages,
add a separate member that tracks if this is a ring mapped provided
buffer list or not.
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In preparation for allowing the kernel to allocate the provided buffer
rings and have the application mmap it instead, abstract out the
current method of pinning and mapping the user allocated ring.
No functional changes intended in this patch.
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Some architectures have memory cache aliasing requirements (e.g. parisc)
if memory is shared between userspace and kernel. This patch fixes the
kernel to return an aliased address when asked by userspace via mmap().
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
io_uring hashes writes to a given file/inode so that it can serialize
them. This is useful if the file system needs exclusive access to the
file to perform the write, as otherwise we end up with a ton of io-wq
threads trying to lock the inode at the same time. This can cause
excessive system time.
But if the file system has flagged that it supports parallel O_DIRECT
writes, then there's no need to serialize the writes. Check for that
through FMODE_DIO_PARALLEL_WRITE and don't hash it if we don't need to.
In a basic test of 8 threads writing to a file on XFS on a gen2 Optane,
with each thread writing in 4k chunks, it improves performance from
~1350K IOPS (or ~5290MiB/sec) to ~1410K IOPS (or ~5500MiB/sec).
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When removing provided buffers, io_buffer structs are not being disposed
of, leading to a memory leak. They can't be freed individually, because
they are allocated in page-sized groups. They need to be added to some
free list instead, such as io_buffers_cache. All callers already hold
the lock protecting it, apart from when destroying buffers, so had to
extend the lock there.
Fixes: cc3cec8367 ("io_uring: speedup provided buffer handling")
Signed-off-by: Wojciech Lukowicz <wlukowicz01@gmail.com>
Link: https://lore.kernel.org/r/20230401195039.404909-2-wlukowicz01@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When a request to remove buffers is submitted, and the given number to be
removed is larger than available in the specified buffer group, the
resulting CQE result will be the number of removed buffers + 1, which is
1 more than it should be.
Previously, the head was part of the list and it got removed after the
loop, so the increment was needed. Now, the head is not an element of
the list, so the increment shouldn't be there anymore.
Fixes: dbc7d452e7 ("io_uring: manage provided buffers strictly ordered")
Signed-off-by: Wojciech Lukowicz <wlukowicz01@gmail.com>
Link: https://lore.kernel.org/r/20230401195039.404909-2-wlukowicz01@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=5IP9
-----END PGP SIGNATURE-----
Merge tag 'io_uring-6.3-2023-03-30' of git://git.kernel.dk/linux
Pull io_uring fixes from Jens Axboe:
- Fix a regression with the poll retry, introduced in this merge window
(me)
- Fix a regression with the alloc cache not decrementing the member
count on removal. Also a regression from this merge window (Pavel)
- Fix race around rsrc node grabbing (Pavel)
* tag 'io_uring-6.3-2023-03-30' of git://git.kernel.dk/linux:
io_uring: fix poll/netmsg alloc caches
io_uring/rsrc: fix rogue rsrc node grabbing
io_uring/poll: clear single/double poll flags on poll arming
Conflicts:
drivers/net/ethernet/mediatek/mtk_ppe.c
3fbe4d8c0e ("net: ethernet: mtk_eth_soc: ppe: add support for flow accounting")
924531326e ("net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These just return the address and length of the current iovec segment
in the iterator. Convert existing iov_iter_iovec() users to use them
instead of getting a copy of the current vec.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe
Josh Triplett
Linus Torvalds
Breno Leitao
Tobias Holl
Jakub Kicinski
David Wei
Pavel Begunkov
Ming Lei
Gabriel Krisman Bertazi
Helge Deller
Wojciech Lukowicz