This adds support for the LED controller on Broadcom's BCM6358.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch adds a driver to support the ktd2692 flash LEDs.
ktd2692 can control flash current by ExpressWire interface.
Signed-off-by: Ingi Kim <ingi2.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This adds support for the LED controller on Broadcom's BCM6328.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch adds a driver for the 1.5A Step-Up Current Regulator
for Flash LEDs. The device is programmed through a Skyworks proprietary
AS2Cwire serial digital interface.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch adds led-flash support to Maxim max77693 chipset.
A device can be exposed to user space through LED subsystem
sysfs interface. Device supports up to two leds which can
work in flash and torch mode. The leds can be triggered
externally or by software.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The TLC59116 is an I2C bus controlled 16-channel LED driver. The
TLC59108 is an I2C bus controlled 8-channel LED driver, which is very
similar to the TLC59116. Each LED output has its own 8-bit
fixed-frequency PWM controller to control the brightness of the LED.
The LEDs can also be fixed off and on, making them suitable for use as
GPOs.
This is based on a driver from Belkin, but has been extensively
rewritten and extended to support both 08 and 16 versions.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Imre Kaloz <kaloz@openwrt.org>
Cc: Matthew.Fatheree@belkin.com
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This adds support for the WLED ('White' LED) block on Qualcomm's
PM8941 PMICs.
(cooloney@gmail.com: remove unneeded semicolon)
Signed-off-by: Courtney Cavin <courtney.cavin@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Some LED devices support two operation modes - torch and flash.
This patch provides support for flash LED devices in the LED subsystem
by introducing new sysfs attributes and kernel internal interface.
The attributes being introduced are: flash_brightness, flash_strobe,
flash_timeout, max_flash_timeout, max_flash_brightness, flash_fault,
flash_sync_strobe and available_sync_leds. All the flash related
features are placed in a separate module.
The modifications aim to be compatible with V4L2 framework requirements
related to the flash devices management. The design assumes that V4L2
sub-device can take of the LED class device control and communicate
with it through the kernel internal interface. When V4L2 Flash sub-device
file is opened, the LED class device sysfs interface is made
unavailable.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Introduce the Texas Instruments lp8860
4 channel LED driver.
This driver configures the device in display cluster mode
as this seems to be the most used configuration at the
time of the driver configuration.
For more product information please see the link below:
http://www.ti.com/product/lp8860-q1
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Convert k10temp, smsc47b397, da9052, da9055 to new hwmon API.
Register ntc_thermistor driver with thermal subsystem.
Add support for F15h M60h to k10temp driver.
Add driver for MEN14F021P00 BMC HWMON driver; this required a merge
with tag mfd-hwmon-leds-watchdog-v3.18.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vI5p
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver for menf21bmc.
- convert k10temp, smsc47b397, da9052, da9055 to new hwmon API.
- register ntc_thermistor driver with thermal subsystem.
- add support for F15h M60h to k10temp driver.
- add driver for MEN14F021P00 BMC HWMON driver; this required a merge
with tag mfd-hwmon-leds-watchdog-v3.18
* tag 'hwmon-for-linus-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ab8500) Call kernel_power_off instead of pm_power_off
hwmon: (menf21bmc) Introduce MEN14F021P00 BMC HWMON driver
leds: leds-menf21bmc: Introduce MEN 14F021P00 BMC LED driver
watchdog: menf21bmc_wdt: Introduce MEN 14F021P00 BMC Watchdog driver
mfd: menf21bmc: Introduce MEN 14F021P00 BMC MFD Core driver
hwmon: (ntc_thermistor) Add ntc thermistor to thermal subsystem as a sensor.
hwmon: (smsc47b397) Convert to devm_hwmon_device_register_with_groups
MAINTAINERS: add entry for the PWM fan driver
hwmon: (k10temp) Convert to devm_hwmon_device_register_with_groups
hwmon: (k10temp) Add support for F15h M60h
hwmon: (da9052) Convert to devm_hwmon_device_register_with_groups
hwmon: (da9055) Convert to devm_hwmon_device_register_with_groups
hwmon: (ads1015) Use of_property_read_u32 at appropriate places
This makes it possible to create a set of LEDs from a syscon
MFD instance, which is lean mean and clean on the ARM
reference designs and can replace the Versatile LEDs driver
in the long run, as well as other custom syscon LEDs drivers.
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
[Fixed cocinelle warnings]
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Added driver to support the 14F021P00 BMC LEDs.
The BMC is a Board Management Controller including four LEDs which
can be switched on and off.
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
A handful of driver-related changes. We've had a bunch of them going in through
other branches as well, so it's only a part of what we really have this release.
Larger pieces are:
* Removal of a now unused PWM driver for atmel
- This includes AVR32 changes that have been appropriately acked.
* Performance counter support for the arm CCN interconnect
* OMAP mailbox driver cleanups and consolidation
* PCI and SATA PHY drivers for SPEAr 13xx platforms
* Redefinition (with backwards compatibility!) of PCI DT bindings for Tegra to
better model regulators/power.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=fsP6
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"A handful of driver-related changes. We've had a bunch of them going
in through other branches as well, so it's only a part of what we
really have this release.
Larger pieces are:
- Removal of a now unused PWM driver for atmel
[ This includes AVR32 changes that have been appropriately acked ]
- Performance counter support for the arm CCN interconnect
- OMAP mailbox driver cleanups and consolidation
- PCI and SATA PHY drivers for SPEAr 13xx platforms
- Redefinition (with backwards compatibility!) of PCI DT bindings for
Tegra to better model regulators/power"
Note: this merge also fixes up the semantic conflict with the new
calling convention for devm_phy_create(), see commit f0ed817638 ("phy:
core: Let node ptr of PHY point to PHY and not of PHY provider") that
came in through Greg's USB tree.
Semantic merge patch by Stephen Rothwell <sfr@canb.auug.org.au> through
the next tree.
* tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
bus: arm-ccn: Fix error handling at event allocation
mailbox/omap: add a parent structure for every IP instance
mailbox/omap: remove the private mailbox structure
mailbox/omap: consolidate OMAP mailbox driver
mailbox/omap: simplify the fifo assignment by using macros
mailbox/omap: remove omap_mbox_type_t from mailbox ops
mailbox/omap: remove OMAP1 mailbox driver
mailbox/omap: use devm_* interfaces
bus: ARM CCN: add PERF_EVENTS dependency
bus: ARM CCN PMU driver
PCI: spear: Remove spear13xx_pcie_remove()
PCI: spear: Fix Section mismatch compilation warning for probe()
ARM: tegra: Remove legacy PCIe power supply properties
PCI: tegra: Remove deprecated power supply properties
PCI: tegra: Implement accurate power supply scheme
ARM: SPEAr13xx: Update defconfigs
ARM: SPEAr13xx: Add pcie and miphy DT nodes
ARM: SPEAr13xx: Add bindings and dt node for misc block
ARM: SPEAr13xx: Fix static mapping table
phy: Add drivers for PCIe and SATA phy on SPEAr13xx
...
This adds a driver for the iPAQ microcontroller LED.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The leds-atmel-pwm driver is now obsolete. It is not used by any mainlined
boards and is replaced by the generic leds_pwm with the pwm-atmel driver using
the generic PWM framework.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Pull LED updates from Bryan Wu:
"I just found merge window is open and I'm quite busy and almost forget
to send out this pull request. Thanks Russell and Alexandre ping me
about this.
So basically we got some clean up and leds-pwm fixing patches from
Russell"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: Remove duplicated OOM message for individual driver
drivers/leds: Replace __get_cpu_var use through this_cpu_ptr
leds: lp55xx: add DT bindings for LP55231
leds: 88pm860x: Fix missing refcount decrement for parent of_node
leds: 88pm860x: Use of_get_child_by_name
leds: leds-pwm: add DT support for LEDs wired to supply
leds: leds-pwm: implement PWM inversion
leds: leds-pwm: convert OF parsing code to use led_pwm_add()
leds: leds-pwm: provide a common function to setup a single led-pwm device
leds: pca9685: Remove leds-pca9685 driver
dell-led: add mic mute led interface
This driver is replaced by pwm-pca9685 driver and there is no user uses this
driver in current tree. So remove it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Acked-by: Maximilian Güntner <maximilian.guentner@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Now that we have converted this driver to a real platform device
module-based thing, we move the driver down into the LEDs
subsystem and rename the config option to LEDS_VERSATILE.
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Pawel Moll <pawel.moll@arm.com>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The NXP PCA9685 supports 16 channels/leds using a 12-bit PWM (4095
levels of brightness)
This driver supports configuration using platform_data.
Signed-off-by: Maximilian Güntner <maximilian.guentner@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Pull led updates from Bryan Wu:
"Sorry for the late pull request, since I'm just back from vacation.
LED subsystem updates for 3.12:
- pca9633 driver DT supporting and pca9634 chip supporting
- restore legacy device attributes for lp5521
- other fixing and updates"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: (28 commits)
leds: wm831x-status: Request a REG resource
leds: trigger: ledtrig-backlight: Fix invalid memory access in fb_event notification callback
leds-pca963x: Fix device tree parsing
leds-pca9633: Rename to leds-pca963x
leds-pca9633: Add mutex to the ledout register
leds-pca9633: Unique naming of the LEDs
leds-pca9633: Add support for PCA9634
leds: lp5562: use LP55xx common macros for device attributes
Documentation: leds-lp5521,lp5523: update device attribute information
leds: lp5523: remove unnecessary writing commands
leds: lp5523: restore legacy device attributes
leds: lp5523: LED MUX configuration on initializing
leds: lp5523: make separate API for loading engine
leds: lp5521: remove unnecessary writing commands
leds: lp5521: restore legacy device attributes
leds: lp55xx: add common macros for device attributes
leds: lp55xx: add common data structure for program
Documentation: leds: Fix a typo
leds: ss4200: Fix incorrect placement of __initdata
leds: clevo-mail: Fix incorrect placement of __initdata
...
The driver now supports the chips pca9633 and pca9634, therefore we
rename the files to more generic and meaningul names
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
LP8501 can drive up to 9 channels like LP5523.
LEDs can be controlled directly via the I2C and programmable engines are
supported.
LP55xx common driver
LP8501 is one of LP55xx family device, so LP55xx common code are used.
Chip specific data is defined in the structure, 'lp55xx_device_config'.
Differences between LP8501 and LP5523
Different register layout for LED output control and others.
LP8501 specific feature for separate output power selection.
LP8501 doesn't support external clock detection.
Different programming engine data.
LP8501 specific feature - output power selection
Output channels are selected by power selection - Vout or Vdd.
Separate power for VDD1-6 and VDD7-9 are available.
It is configurable in the platform data.
To support this feature, LP55xx DT structure and header are changed.
Device tree binding is updated as well.
LED pattern data
Example pattern data is updated in the driver documentation.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The driver is superseded by the generic pwm-renesas-tpu driver used with
leds-pwm.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
For better driver management, new subdirectory, 'trigger' is created.
All LED trigger drivers are moved into this directory.
Internal header, 'leds.h' is included in each LED trigger drivers.
Fix the location of header file, "leds.h" -> "../leds.h" in driver files.
One exception is here, 'ledtrig-timer.c'.
There is no need to include 'leds.h'. so '#include "leds.h"' line was removed.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
LP5562 can drive up to 4 channels, RGB and White.
LEDs can be controlled directly via the led class control interface.
LP55xx common driver
LP5562 is one of LP55xx family device, so LP55xx common code are used.
On the other hand, chip specific configuration is defined in the structure
'lp55xx_device_config'
LED pattern data
LP5562 has also internal program memory which is used for running various LED
patterns. LP5562 driver supports the firmware interface and the predefined
pattern data as well.
LP5562 device attributes: 'led_pattern' and 'engine_mux'
A 'led_pattern' is an index code which runs the predefined pattern data.
And 'engine_mux' is updated with the firmware interface is activated.
Detailed description has been updated in the documentation files,
'leds-lp55xx.txt' and 'leds-lp5562.txt'.
Changes on the header file
LP5562 configurable definitions are added.
Pattern RGB data is fixed as constant value.
(No side effect on other devices, LP5521 or LP5523.)
(cooloney@gmail.com: remove redundant mutex_unlock(). Reported by Dan
Carpenter <dan.carpenter@oracle.com>)
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch supports basic common driver code for LP5521, LP5523/55231 devices.
( Driver Structure Data )
lp55xx_led and lp55xx_chip
In lp55xx common driver, two different data structure is used.
o lp55xx_led
control multi output LED channels such as led current, channel index.
o lp55xx_chip
general chip control such like the I2C and platform data.
For example, LP5521 has maximum 3 LED channels.
LP5523/55231 has 9 output channels.
lp55xx_chip for LP5521 ... lp55xx_led #1
lp55xx_led #2
lp55xx_led #3
lp55xx_chip for LP5523 ... lp55xx_led #1
lp55xx_led #2
.
.
lp55xx_led #9
( Platform Data )
LP5521 and LP5523/55231 have own specific platform data.
However, this data can be handled with just one platform data structure.
The lp55xx platform data is declared in the header.
This structure is derived from leds-lp5521.h and leds-lp5523.h
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Pull LED subsystem update from Bryan Wu.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: (24 commits)
leds: add output driver configuration for pca9633 led driver
leds: lm3642: Use regmap_update_bits() in lm3642_chip_init()
leds: Add new LED driver for lm3642 chips
leds-lp5523: Fix riskiness of the page fault
leds-lp5523: turn off the LED engines on unloading the driver
leds-lm3530: Fix smatch warnings
leds-lm3530: Use devm_regulator_get function
leds: leds-gpio: adopt pinctrl support
leds: Add new LED driver for lm355x chips
leds-lp5523: use the i2c device id rather than fixed name
leds-lp5523: add new device id for LP55231
leds-lp5523: support new LP55231 device
leds: triggers: send uevent when changing triggers
leds-lp5523: minor code style fixes
leds-lp5523: change the return type of lp5523_set_mode()
leds-lp5523: set the brightness to 0 forcely on removing the driver
leds-lp5523: add channel name in the platform data
leds: leds-gpio: Use of_get_child_count() helper
leds: leds-gpio: Use platform_{get,set}_drvdata
leds: leds-gpio: use of_match_ptr()
...
This driver is a general version for LM642 led chip of TI.
LM3642 :
The LM3642 is a 4MHz fixed-frequency synchronous boost
converter plus 1.5A constant current driver for a high-current
white LED.
The LM3642 is controlled via an I2C-compatible interface.
Signed-off-by: G.Shark Jeong <gshark.jeong@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
This driver is a general version for LM355x,lm3554 and lm3556,led chips of TI.
LM3554 :
The LM3554 is a 2 MHz fixed-frequency synchronous boost
converter with 1.2A dual high side led drivers.
Datasheet: www.ti.com/lit/ds/symlink/lm3554.pdf
LM3556 :
The LM3556 is a 4 MHz fixed-frequency synchronous boost
converter plus 1.5A constant current driver for a high-current white LED.
Datasheet: www.national.com/ds/LM/LM3556.pdf
(bryan.wu@canonical.com: use flush_work() to replace flush_work_sync() which is
deprecated)
Signed-off-by: G.Shark Jeong <gshark.jeong@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
From Bryan Wu <bryan.wu@canonical.com>:
Based on Linus Walleij's ARM LED consolidation work, this patchset introduce a
new generic led trigger for CPU not only for ARM but also for others.
For enabling CPU idle event, CPU arch code should call ledtrig_cpu() stub to
trigger idle start or idle end event.
These patches convert old style LED driver in arch/arm to gpio_led or new led
driver interface. Against 3.5 release and build successfully for all the machines.
Test ledtrig-cpu driver on OMAP4 Panda board.
v9 --> v10
* fix compiling issue on versatile_defconfig reported by Russell King
* rebase to 3.5 kernel and move patches to new git tree
v8 --> v9:
* use mutex to replace rw_sema pointed out by Tim Gardner
* add a new struct led_trigger_cpu
* add lock_is_inited to record mutex lock initialization
v6 --> v7:
* add a patch to unify the led-trigger name
* fix some typo pointed
* use BUG_ON to detect CPU numbers during building stage
v5 --> v6:
* replace __get_cpu_var() to per_cpu()
* remove smp_processor_id() which is wrong with for_each_possible_cpu()
* test on real OMAP4 Panda board
* add comments about CPU hotplug in the CPU LED trigger driver
v4 --> v5:
* rebase all the patches on top of latest linux-next
* replace on_each_cpu() with for_each_possible_cpu()
* add some description of ledtrig_cpu() API
* remove old leds code from driver nwflash.c, which should use a new led trigger then
* this trigger driver can be built as module now
v3 --> v4:
* fix a typo pointed by Jochen Friedrich
* fix some building errors
* add Reviewed-by and Tested-by into patch log
v2 --> v3:
* almost rewrote the whole ledtrig-cpu driver, which is more simple
* every CPU will have a per-CPU trigger
* cpu trigger can be assigned to any leds
* fix a lockdep issue in led-trigger common code
* other fix according to review
v1 --> v2:
* remove select operations in Kconfig of every machines
* add back supporting of led in core module of mach-integrator
* solidate name scheme in ledtrig-cpu.c
* add comments of CPU_LED_* cpu led events
* fold patches of RealView and Versatile together
* add machine_is_ check during assabet led driver init
* add some Acked-by in patch logs
* remove code for simpad machine in machine-sa11000, since Jochen Friedrich
introduced gpiolib and gpio-led driver for simpad
* on Assabet and Netwinder machine, LED operations is reversed like:
setting bit means turn off leds
clearing bit means turn on leds
* add a new function to read CM_CTRL register for led driver
* 'for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
ARM: use new LEDS CPU trigger stub to replace old one
ARM: mach-sa1100: retire custom LED code
ARM: mach-omap1: retire custom LED code
ARM: mach-pnx4008: remove including old leds event API header file
ARM: plat-samsung: remove including old leds event API header file
ARM: mach-pxa: retire custom LED code
char: nwflash: remove old led event code
ARM: mach-footbridge: retire custom LED code
ARM: mach-ebsa110: retire custom LED code
ARM: mach-clps711x: retire custom LED code of P720T machine
ARM: mach-integrator: retire custom LED code
ARM: mach-integrator: move CM_CTRL to header file for accessing by other functions
ARM: mach-orion5x: convert custom LED code to gpio_led and LED CPU trigger
ARM: mach-shark: retire custom LED code
ARM: mach-ks8695: remove leds driver, since nobody use it
ARM: mach-realview and mach-versatile: retire custom LED code
ARM: at91: convert old leds drivers to gpio_led and led_trigger drivers
led-triggers: create a trigger for CPU activity
Conflicts:
arch/arm/mach-clps711x/p720t.c
arch/arm/mach-sa1100/leds-cerf.c
arch/arm/mach-sa1100/leds-lart.c
Let's hope this is the last time we pull this and it doesn't cause
more trouble. I have verified that version 10 causes no build
warnings or errors any more, and the patches still look good.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Attempting to consolidate the ARM LED code, this removes the
custom RealView LED trigger code to turn LEDs on and off in
response to CPU activity and replace it with a standard trigger.
(bryan.wu@canonical.com:
It introduces several syscore stubs into this trigger.
It also provides ledtrig_cpu trigger event stub in <linux/leds.h>.
Although it was inspired by ARM work, it can be used in other arch.)
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Tested-by: Jochen Friedrich <jochen@scram.de>
TI LP8788 PMU has the current sink as the keyboard led driver.
The brightness is controlled by the i2c commands.
Configurable parameters can be defined in the platform side.
Patch v2.
(a) use workqueue on changing the brightness
(b) use mutex_lock/unlock when the brightness is set
and the led block of lp8788 device is enabled
(c) remove err_dev on _probe()
: just return as returned value if any errors
(d) replace module_init/exit() with module_platform_driver()
(e) add led configuration structure and loading them by default
if platform data is null
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Add driver for BlinkM device to drivers/leds/.
Add entry to MAINTAINERS file.
Add documentation in Documentation/leds/.
A BlinkM is a RGB LED controlled through I2C.
This driver implements an interface to the LED framework
and another sysfs group to access the internal options
of the BlinkM.
rev6: Use module_i2c_driver().
rev5: Removed own workqueue in favor of events wq.
rev4: Fixed comments by Bryan Wu.
rev3: Fixed issues found by Jonathan Neuschäfer.
(bryan.wu@canonical.com: remove 2 trailing whitespace)
Signed-off-by: Jan-Simon Möller <jansimon.moeller@gmx.de>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
LM3556 :
The LM3556 is a 4 MHz fixed-frequency synchronous boost
converter plus 1.5A constant current driver for a high-current white LED.
Datasheet: www.national.com/ds/LM/LM3556.pdf
Tested on OMAP4430
(bryan.wu@canonical.com: use module_i2c_driver() rather than
lm3556_init/lm3556_exit for code simplicity; fixed some typo
pointed out by Rob Landley)
Signed-off-by: G.Shark Jeong <gshark.jeong@gmail.com>
Reviewed-by: Axel Lin <axel.lin@gmail.com>
Reviewed-by: Kim, Milo <Milo.Kim@ti.com>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Add oneshot trigger to blink a led with configurale parameters via
sysfs.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Cc: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Add sub-driver for the LEDs on National Semiconductor / TI LM3533 lighting
power chips.
The chip provides 256 brightness levels, hardware accelerated blinking as
well as ambient-light-sensor and pwm input control.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Rob Landley <rob@landley.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The leds timer trigger does not currently have an interface to activate a
one shot timer. The current support allows for setting two timers, one
for specifying how long a state to be on, and the second for how long the
state to be off. The delay_on value specifies the time period an LED
should stay in on state, followed by a delay_off value that specifies how
long the LED should stay in off state. The on and off cycle repeats until
the trigger gets deactivated. There is no provision for one time
activation to implement features that require an on or off state to be
held just once and then stay in the original state forever.
Without one shot timer interface, user space can still use timer trigger
to set a timer to hold a state, however when user space application
crashes or goes away without deactivating the timer, the hardware will be
left in that state permanently.
As a specific example of this use-case, let's look at vibrate feature on
phones. Vibrate function on phones is implemented using PWM pins on SoC
or PMIC. There is a need to activate one shot timer to control the
vibrate feature, to prevent user space crashes leaving the phone in
vibrate mode permanently causing the battery to drain.
This trigger exports three properties, activate, state, and duration When
transient trigger is activated these properties are set to default values.
- duration allows setting timer value in msecs. The initial value is 0.
- activate allows activating and deactivating the timer specified by
duration as needed. The initial and default value is 0. This will allow
duration to be set after trigger activation.
- state allows user to specify a transient state to be held for the specified
duration.
Signed-off-by: Shuah Khan <shuahkhan@gmail.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: NeilBrown <neilb@suse.de>
Cc: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These changes are all specific to one board only. We're trying to keep
the number of board files low, but generally board level updates are
ok on platforms that are working on moving towards DT based probing,
which will eventually lead to removing them.
The board-ams-delta.c board file gets a conflict between the removal of
ams_delta_config and the addition of a lot of other data. The Kconfig
file has two changes in the same line, and in exynos, the power domain
cleanup conflicts with the addition of the image sensor device.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: Amended a fix for a mismerge to board-omap4panda.c]
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HPiJ
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: board specific updates" from Arnd Bergmann/Olof Johansson:
"These changes are all specific to one board only. We're trying to
keep the number of board files low, but generally board level updates
are ok on platforms that are working on moving towards DT based
probing, which will eventually lead to removing them.
The board-ams-delta.c board file gets a conflict between the removal
of ams_delta_config and the addition of a lot of other data. The
Kconfig file has two changes in the same line, and in exynos, the
power domain cleanup conflicts with the addition of the image sensor
device.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: Amended a fix for a mismerge to board-omap4panda.c]
Signed-off-by: Olof Johansson <olof@lixom.net>"
Fixed up some fairly trivial conflicts manually.
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (82 commits)
i.MX35-PDK: Add Camera support
ARM : mx35: 3ds-board: add framebuffer device
pxa/hx4700: Remove pcmcia platform_device structure
ARM: pxa/hx4700: Reduce sleep mode battery discharge by 35%
ARM: pxa/hx4700: Remove unwanted request for GPIO105
ARM: EXYNOS: support Exynos4210-bus Devfreq driver on Nuri board
ARM: EXYNOS: Register JPEG on nuri
ARM: EXYNOS: Register JPEG on universal_c210
ARM: S5PV210: Enable JPEG on SMDKV210
ARM: S5PV210: Add JPEG board definition
ARM: EXYNOS: Enable JPEG on Origen
ARM: EXYNOS: Enable JPEG on SMDKV310
ARM: EXYNOS: Add __init attribute to universal_camera_init()
ARM: EXYNOS: Add __init attribute to nuri_camera_init()
ARM: S5PV210: Enable FIMC on SMDKC110
ARM: S5PV210: Enable FIMC on SMDKV210
ARM: S5PV210: Enable MFC on SMDKC110
ARM: S5PV210: Enable MFC on SMDKV210
ARM: EXYNOS: Enable G2D on SMDKV310
ARM: tegra: update defconfig
...
Add platform driver for the Soekris Engineering net5501 single-board
computer. Probes well-known locations in ROM for BIOS signature
to confirm correct platform. Registers 1 LED and 1 GPIO-based
button (typically used for soft reset).
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Andres Salomon <dilinger@queued.net>
Cc: Matthew Garrett <mjg@redhat.com>
[ Removed Kconfig and Makefile detritus from drivers/leds/]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-jv5uf34996juqh5syes8mn4h@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'omap1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
input: serio: ams-delta: toggle keyboard power over GPIO
omapfb: lcd_ams_delta: drive control lines over GPIO
MTD: NAND: ams-delta: use GPIO instead of custom I/O
LED: drop leds-ams-delta driver
ARM: OMAP1: ams-delta: supersede custom led device by leds-gpio
ARM: OMAP1: ams-delta: convert latches to basic_mmio_gpio
ARM: OMAP1: ams-delta: register latch dependent devices later
Add support for leds on Bachmann's ot200 visualisation device. The
device has three leds on the back panel (led_err, led_init and led_run)
and can handle up to seven leds on the front panel.
The driver was written by Linutronix on behalf of Bachmann electronic
GmbH. It incorporates feedback from Lars-Peter Clausen
[akpm@linux-foundation.org: add dependency on HAS_IOMEM]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
rtc: max8925: Add function to work as wakeup source
mfd: Add pm ops to max8925
mfd: Convert aat2870 to dev_pm_ops
mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
mfd: Introduce missing kfree in 88pm860x probe routine
mfd: Add S5M series configuration
mfd: Add s5m series irq driver
mfd: Add S5M core driver
mfd: Improve mc13xxx dt binding document
mfd: Fix stmpe section mismatch
mfd: Fix stmpe build warning
mfd: Fix STMPE I2c build failure
mfd: Constify aat2870-core i2c_device_id table
gpio: Add support for stmpe variant 801
mfd: Add support for stmpe variant 801
mfd: Add support for stmpe variant 610
mfd: Add support for STMPE SPI interface
mfd: Separate out STMPE controller and interface specific code
misc: Remove max8997-muic sysfs attributes
mfd: Remove unused wm831x_irq_data_to_mask_reg()
...
Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.
TI's TCA6507 is the LED driver in the GTA04 Openmoko motherboard. The
driver provides full support for brightness levels and hardware blinking.
This driver can drive each of 7 outputs as an LED or a GPIO output,
and provides hardware-assist blinking.
[akpm@linux-foundation.org: fix __mod_i2c_device_table alias]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch enables LED controller in MAX8997 PMIC.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This driver is no longer needed after the Amstrad Delta on-board LED
devices have been converted to leds-gpio compatible.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add V2 of the LED driver for a single timer channel for the TPU hardware
block commonly found in Renesas SoCs.
The driver has been written with optimal Power Management in mind, so to
save power the LED is driven as a regular GPIO pin in case of maximum
brightness and power off which allows the TPU hardware to be idle and
which in turn allows the clocks to be stopped and the power domain to be
turned off transparently.
Any other brightness level requires use of the TPU hardware in PWM mode.
TPU hardware device clocks and power are managed through Runtime PM.
System suspend and resume is known to be working - during suspend the LED
is set to off by the generic LED code.
The TPU hardware timer is equipeed with a 16-bit counter together with an
up-to-divide-by-64 prescaler which makes the hardware suitable for
brightness control. Hardware blink is unsupported.
The LED PWM waveform has been verified with a Fluke 123 Scope meter on a
sh7372 Mackerel board. Tested with experimental sh7372 A3SP power domain
patches. Platform device bind/unbind tested ok.
V2 has been tested on the DS2 LED of the sh73a0-based AG5EVM.
[axel.lin@gmail.com: include linux/module.h]
Signed-off-by: Magnus Damm <damm@opensource.se>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This new driver replaces the old PCEngines Alix 2/3 LED driver with a
new driver that controls the LEDs through the leds-gpio driver. The
old driver accessed GPIOs directly, which created a conflict and
prevented also loading the cs5535-gpio driver to read other GPIOs on
the Alix board. With this new driver, we hook into leds-gpio which in
turn uses GPIO to control the LEDs and therefore it's possible to
control both the LEDs and access onboard GPIOs
Driver is moved to platform/geode as requested by Grant and any other
geode initialisation modules should move here also
This driver is inspired by leds-net5501.c by Alessandro Zummo.
Ideally, leds-net5501.c should also be moved to platform/geode.
Additionally the driver relies on parts of the patch: 7f131cf3ed ("leds:
leds-alix2c - take port address from MSR) by Daniel Mack to perform
detection of the Alix board.
[akpm@linux-foundation.org: include module.h]
Signed-off-by: Ed Wildgoose <kernel@wildgooses.com>
Cc: git@wildgooses.com
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Álvaro Fernández Rojas
Ingi Kim
Jacek Anaszewski
Andrew Lunn
Courtney Cavin
Dan Murphy
Linus Torvalds
Linus Walleij
Andreas Werner
Alexandre Belloni
Axel Lin
Maximilian Güntner
Ricardo Ribalda Delgado
Kim, Milo
Laurent Pinchart
G.Shark Jeong
Arnd Bergmann
Bryan Wu
Jan-Simon Möller
Fabio Baltieri
Johan Hovold
Shuah Khan
David Dajun Chen
Peter Meerwald
Philip Prindeville
Sebastian Andrzej Siewior
Tony Lindgren
NeilBrown
Donggeun Kim
Janusz Krzysztofik
Magnus Damm
Ed Wildgoose