Expose port function commands to enable / disable migratable
capability, this is used to set the port function as migratable.
Live migration is the process of transferring a live virtual machine
from one physical host to another without disrupting its normal
operation.
In order for a VM to be able to perform LM, all the VM components must
be able to perform migration. e.g.: to be migratable.
In order for VF to be migratable, VF must be bound to VFIO driver with
migration support.
When migratable capability is enabled for a function of the port, the
device is making the necessary preparations for the function to be
migratable, which might include disabling features which cannot be
migrated.
Example of LM with migratable function configuration:
Set migratable of the VF's port function.
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0
vfnum 1
function:
hw_addr 00:00:00:00:00:00 migratable disable
$ devlink port function set pci/0000:06:00.0/2 migratable enable
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0
vfnum 1
function:
hw_addr 00:00:00:00:00:00 migratable enable
Bind VF to VFIO driver with migration support:
$ echo <pci_id> > /sys/bus/pci/devices/0000:08:00.0/driver/unbind
$ echo mlx5_vfio_pci > /sys/bus/pci/devices/0000:08:00.0/driver_override
$ echo <pci_id> > /sys/bus/pci/devices/0000:08:00.0/driver/bind
Attach VF to the VM.
Start the VM.
Perform LM.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Expose port function commands to enable / disable RoCE, this is used to
control the port RoCE device capabilities.
When RoCE is disabled for a function of the port, function cannot create
any RoCE specific resources (e.g GID table).
It also saves system memory utilization. For example disabling RoCE enable a
VF/SF saves 1 Mbytes of system memory per function.
Example of a PCI VF port which supports function configuration:
Set RoCE of the VF's port function.
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0
vfnum 1
function:
hw_addr 00:00:00:00:00:00 roce enable
$ devlink port function set pci/0000:06:00.0/2 roce disable
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0
vfnum 1
function:
hw_addr 00:00:00:00:00:00 roce disable
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to avoid partial request processing, validate the request
before processing it.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 'group' argument is not modified, so mark it as 'const'. It will
allow us to constify arguments of the callers of this function in future
patches.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drop the first three arguments and instead extract them from the MDB
configuration structure.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The checks only require information parsed from the RTM_NEWMDB netlink
message and do not rely on any state stored in the bridge driver.
Therefore, there is no need to perform the checks in the critical
section under the multicast lock.
Move the checks out of the critical section.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The parsing of the netlink messages and the validity checks are now
performed in br_mdb_config_init() so we can remove br_mdb_parse().
This finally allows us to stop passing netlink attributes deep in the
MDB control path and only use the MDB configuration structure.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MDB group key (i.e., {source, destination, protocol, VID}) is
currently determined under the multicast lock from the netlink
attributes. Instead, use the group key from the MDB configuration
structure that was prepared before acquiring the lock.
No functional changes intended.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As an intermediate step towards only using the new MDB configuration
structure, pass it further in the control path instead of passing
individual attributes.
No functional changes intended.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MDB configuration structure (i.e., struct br_mdb_config) now
includes all the necessary information from the parsed RTM_{NEW,DEL}MDB
netlink messages, so use it.
This will later allow us to delete the calls to br_mdb_parse() from
br_mdb_add() and br_mdb_del().
No functional changes intended.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These checks are now redundant as they are performed by
br_mdb_config_init() while parsing the RTM_{NEW,DEL}MDB messages.
Remove them.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Netlink attributes are currently passed deep in the MDB creation call
chain, making it difficult to add new attributes. In addition, some
validity checks are performed under the multicast lock although they can
be performed before it is ever acquired.
As a first step towards solving these issues, parse the RTM_{NEW,DEL}MDB
messages into a configuration structure, relieving other functions from
the need to handle raw netlink attributes.
Subsequent patches will convert the MDB code to use this configuration
structure.
This is consistent with how other rtnetlink objects are handled, such as
routes and nexthops.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the
value to be returned to user space.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/202212051918564721658@zte.com.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stefan Schmidt says:
====================
ieee802154-next 2022-12-05
Miquel continued his work towards full scanning support. For this,
we now allow the creation of dedicated coordinator interfaces
to allow a PAN coordinator to serve in the network and set
the needed address filters with the hardware.
On top of this we have the first part to allow scanning for available
15.4 networks. A new netlink scan group, within the existing nl802154
API, was added.
In addition Miquel fixed two issues that have been introduced in the former
patches to free an skb correctly and clarifying an expression in the stack.
From David Girault we got tracing support when registering new PANs.
* tag 'ieee802154-for-net-next-2022-12-05' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan-next:
mac802154: Trace the registration of new PANs
ieee802154: Advertize coordinators discovery
mac802154: Allow the creation of coordinator interfaces
mac802154: Clarify an expression
mac802154: Move an skb free within the rx path
====================
Link: https://lore.kernel.org/r/20221205131909.1871790-1-stefan@datenfreihafen.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The memcpy() in ncsi_cmd_handler_oem deserializes nca->data into a
flexible array structure that overlapping with non-flex-array members
(mfr_id) intentionally. Since the mem_to_flex() API is not finished,
temporarily silence this warning, since it is a false positive, using
unsafe_memcpy().
Reported-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/netdev/CACPK8Xdfi=OJKP0x0D1w87fQeFZ4A2DP2qzGCRcuVbpU-9=4sQ@mail.gmail.com/
Cc: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221202212418.never.837-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add netlink based support for "ethtool -x <dev> [context x]"
command by implementing ETHTOOL_MSG_RSS_GET netlink message.
This is equivalent to functionality provided via ETHTOOL_GRSSH
in ioctl path. It sends RSS table, hash key and hash function
of an interface to user space.
This patch implements existing functionality available
in ioctl path and enables addition of new RSS context
based parameters in future.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Link: https://lore.kernel.org/r/20221202002555.241580-1-sudheer.mogilappagari@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=WjuN
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-next-20221201-b' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Increasing SACK size and moving away from softirq, parts 2 & 3
Here are the second and third parts of patches in the process of moving
rxrpc from doing a lot of its stuff in softirq context to doing it in an
I/O thread in process context and thereby making it easier to support a
larger SACK table.
The full description is in the description for the first part[1] which is
already in net-next.
The second part includes some cleanups, adds some testing and overhauls
some tracing:
(1) Remove declaration of rxrpc_kernel_call_is_complete() as the
definition is no longer present.
(2) Remove the knet() and kproto() macros in favour of using tracepoints.
(3) Remove handling of duplicate packets from recvmsg. The input side
isn't now going to insert overlapping/duplicate packets into the
recvmsg queue.
(4) Don't use the rxrpc_conn_parameters struct in the rxrpc_connection or
rxrpc_bundle structs - rather put the members in directly.
(5) Extract the abort code from a received abort packet right up front
rather than doing it in multiple places later.
(6) Use enums and symbol lists rather than __builtin_return_address() to
indicate where a tracepoint was triggered for local, peer, conn, call
and skbuff tracing.
(7) Add a refcount tracepoint for the rxrpc_bundle struct.
(8) Implement an in-kernel server for the AFS rxperf testing program to
talk to (enabled by a Kconfig option).
This is tagged as rxrpc-next-20221201-a.
The third part introduces the I/O thread and switches various bits over to
running there:
(1) Fix call timers and call and connection workqueues to not hold refs on
the rxrpc_call and rxrpc_connection structs to thereby avoid messy
cleanup when the last ref is put in softirq mode.
(2) Split input.c so that the call packet processing bits are separate
from the received packet distribution bits. Call packet processing
gets bumped over to the call event handler.
(3) Create a per-local endpoint I/O thread. Barring some tiny bits that
still get done in softirq context, all packet reception, processing
and transmission is done in this thread. That will allow a load of
locking to be removed.
(4) Perform packet processing and error processing from the I/O thread.
(5) Provide a mechanism to process call event notifications in the I/O
thread rather than queuing a work item for that call.
(6) Move data and ACK transmission into the I/O thread. ACKs can then be
transmitted at the point they're generated rather than getting
delegated from softirq context to some process context somewhere.
(7) Move call and local processor event handling into the I/O thread.
(8) Move cwnd degradation to after packets have been transmitted so that
they don't shorten the window too quickly.
A bunch of simplifications can then be done:
(1) The input_lock is no longer necessary as exclusion is achieved by
running the code in the I/O thread only.
(2) Don't need to use sk->sk_receive_queue.lock to guard socket state
changes as the socket mutex should suffice.
(3) Don't take spinlocks in RCU callback functions as they get run in
softirq context and thus need _bh annotations.
(4) RCU is then no longer needed for the peer's error_targets list.
(5) Simplify the skbuff handling in the receive path by dropping the ref
in the basic I/O thread loop and getting an extra ref as and when we
need to queue the packet for recvmsg or another context.
(6) Get the peer address earlier in the input process and pass it to the
users so that we only do it once.
This is tagged as rxrpc-next-20221201-b.
Changes:
========
ver #2)
- Added a patch to change four assertions into warnings in rxrpc_read()
and fixed a checker warning from a __user annotation that should have
been removed..
- Change a min() to min_t() in rxperf as PAGE_SIZE doesn't seem to match
type size_t on i386.
- Three error handling issues in rxrpc_new_incoming_call():
- If not DATA or not seq #1, should drop the packet, not abort.
- Fix a goto that went to the wrong place, dropping a non-held lock.
- Fix an rcu_read_lock that should've been an unlock.
Tested-by: Marc Dionne <marc.dionne@auristor.com>
Tested-by: kafs-testing+fedora36_64checkkafs-build-144@auristor.com
Link: https://lore.kernel.org/r/166794587113.2389296.16484814996876530222.stgit@warthog.procyon.org.uk/ [1]
Link: https://lore.kernel.org/r/166982725699.621383.2358362793992993374.stgit@warthog.procyon.org.uk/ # v1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for drivers wanting to set SW IRQ coalescing
by default. The related sysfs attributes can be used to
override the default values.
Follow Jakub's suggestion and put this functionality into
net core so that drivers wanting to use software interrupt
coalescing per default don't have to open-code it.
Note that this function needs to be called before the
netdevice is registered.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kfree_rcu(1-arg) should be avoided as much as possible,
since this is only possible from sleepable contexts,
and incurr extra rcu barriers.
I wish the 1-arg variant of kfree_rcu() would
get a distinct name, like kfree_rcu_slow()
to avoid it being abused.
Fixes: 459837b522 ("net/tcp: Disable TCP-MD5 static key on tcp_md5sig_info destruction")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20221202052847.2623997-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Third set of patches for v6.2. mt76 has a new driver for mt7996 Wi-Fi 7
devices and iwlwifi also got initial Wi-Fi 7 support. Otherwise
smaller features and fixes.
Major changes:
ath10k
* store WLAN firmware version in SMEM image table
mt76
* mt7996: new driver for MediaTek Wi-Fi 7 (802.11be) devices
* mt7986, mt7915: enable Wireless Ethernet Dispatch (WED) offload support
* mt7915: add ack signal support
* mt7915: enable coredump support
* mt7921: remain_on_channel support
* mt7921: channel context support
iwlwifi
* enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities
* 320 MHz channels support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmOKcMARHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZv3cgf+KjlbxtCZvEIfK+jsd2/VK635ucUdC1d5
QZB5SCHyVCqTMEsBBw0WCmFdfnqQRQUE9Qe5s0hlwhyrjLP4FQ6/jGTarFvRV43E
xO8jJd7e4mnVVoQySeKIRfvtYPFKT5GpaDVs4ytfdSs+KYoCE7akMBcvHVO8Fr2M
MepdqyoJakhRybFUJZMts8W8IsBikv9hdnb2Mr/E32JFLeP6ggs9tKCZKBbpxyXk
BzfYkDMXffFl95prlmy4rXP223FjvgUuRNWaatseR7S6A/Ik9Xk3B1qv3mtocPZF
LiTlFtmn3qkgyX5bfm6NRe/2FqgRUYfIrN0XtVw6Sy8WUe1GCf3opA==
=pkqE
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.2
Third set of patches for v6.2. mt76 has a new driver for mt7996 Wi-Fi 7
devices and iwlwifi also got initial Wi-Fi 7 support. Otherwise
smaller features and fixes.
Major changes:
ath10k
- store WLAN firmware version in SMEM image table
mt76
- mt7996: new driver for MediaTek Wi-Fi 7 (802.11be) devices
- mt7986, mt7915: enable Wireless Ethernet Dispatch (WED) offload support
- mt7915: add ack signal support
- mt7915: enable coredump support
- mt7921: remain_on_channel support
- mt7921: channel context support
iwlwifi
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities
- 320 MHz channels support
* tag 'wireless-next-2022-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (144 commits)
wifi: ath10k: fix QCOM_SMEM dependency
wifi: mt76: mt7921e: add pci .shutdown() support
wifi: mt76: mt7915: mmio: fix naming convention
wifi: mt76: mt7996: add support to configure spatial reuse parameter set
wifi: mt76: mt7996: enable ack signal support
wifi: mt76: mt7996: enable use_cts_prot support
wifi: mt76: mt7915: rely on band_idx of mt76_phy
wifi: mt76: mt7915: enable per bandwidth power limit support
wifi: mt76: mt7915: introduce mt7915_get_power_bound()
mt76: mt7915: Fix PCI device refcount leak in mt7915_pci_init_hif2()
wifi: mt76: do not send firmware FW_FEATURE_NON_DL region
wifi: mt76: mt7921: Add missing __packed annotation of struct mt7921_clc
wifi: mt76: fix coverity overrun-call in mt76_get_txpower()
wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices
wifi: mt76: mt76x0: remove dead code in mt76x0_phy_get_target_power
wifi: mt76: mt7915: fix band_idx usage
wifi: mt76: mt7915: enable .sta_set_txpwr support
wifi: mt76: mt7915: add basedband Txpower info into debugfs
wifi: mt76: mt7915: add support to configure spatial reuse parameter set
wifi: mt76: mt7915: add missing MODULE_PARM_DESC
...
====================
Link: https://lore.kernel.org/r/20221202214254.D0D3DC433C1@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some devlink instances may contain thousands of ports. Storing them in
linked list and looking them up is not scalable. Convert the linked list
into xarray.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
self_node_db is a list_head with one entry of struct hsr_node. The
purpose is to hold the two MAC addresses of the node itself.
It is convenient to recycle the structure. However having a list_head
and fetching always the first entry is not really optimal.
Created a new data strucure contaning the two MAC addresses named
hsr_self_node. Access that structure like an RCU protected pointer so
it can be replaced on the fly without blocking the reader.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
hsr_register_frame_out() compares new sequence_nr vs the old one
recorded in hsr_node::seq_out and if the new sequence_nr is higher then
it will be written to hsr_node::seq_out as the new value.
This operation isn't locked so it is possible that two frames with the
same sequence number arrive (via the two slave devices) and are fed to
hsr_register_frame_out() at the same time. Both will pass the check and
update the sequence counter later to the same value. As a result the
content of the same packet is fed into the stack twice.
This was noticed by running ping and observing DUP being reported from
time to time.
Instead of using the hsr_priv::seqnr_lock for the whole receive path (as
it is for sending in the master node) add an additional lock that is only
used for sequence number checks and updates.
Add a per-node lock that is used during sequence number reads and
updates.
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sending frames via the hsr (master) device requires a sequence number
which is tracked in hsr_priv::sequence_nr and protected by
hsr_priv::seqnr_lock. Each time a new frame is sent, it will obtain a
new id and then send it via the slave devices.
Each time a packet is sent (via hsr_forward_do()) the sequence number is
checked via hsr_register_frame_out() to ensure that a frame is not
handled twice. This make sense for the receiving side to ensure that the
frame is not injected into the stack twice after it has been received
from both slave ports.
There is no locking to cover the sending path which means the following
scenario is possible:
CPU0 CPU1
hsr_dev_xmit(skb1) hsr_dev_xmit(skb2)
fill_frame_info() fill_frame_info()
hsr_fill_frame_info() hsr_fill_frame_info()
handle_std_frame() handle_std_frame()
skb1's sequence_nr = 1
skb2's sequence_nr = 2
hsr_forward_do() hsr_forward_do()
hsr_register_frame_out(, 2) // okay, send)
hsr_register_frame_out(, 1) // stop, lower seq duplicate
Both skbs (or their struct hsr_frame_info) received an unique id.
However since skb2 was sent before skb1, the higher sequence number was
recorded in hsr_register_frame_out() and the late arriving skb1 was
dropped and never sent.
This scenario has been observed in a three node HSR setup, with node1 +
node2 having ping and iperf running in parallel. From time to time ping
reported a missing packet. Based on tracing that missing ping packet did
not leave the system.
It might be possible (didn't check) to drop the sequence number check on
the sending side. But if the higher sequence number leaves on wire
before the lower does and the destination receives them in that order
and it will drop the packet with the lower sequence number and never
inject into the stack.
Therefore it seems the only way is to lock the whole path from obtaining
the sequence number and sending via dev_queue_xmit() and assuming the
packets leave on wire in the same order (and don't get reordered by the
NIC).
Cover the whole path for the master interface from obtaining the ID
until after it has been forwarded via hsr_forward_skb() to ensure the
skbs are sent to the NIC in the order of the assigned sequence numbers.
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The hsr device is a software device. Its
net_device_ops::ndo_start_xmit() routine will process the packet and
then pass the resulting skb to dev_queue_xmit().
During processing, hsr acquires a lock with spin_lock_bh()
(hsr_add_node()) which needs to be promoted to the _irq() suffix in
order to avoid a potential deadlock.
Then there are the warnings in dev_queue_xmit() (due to
local_bh_disable() with disabled interrupts) left.
Instead trying to address those (there is qdisc and…) for netpoll sake,
just disable netpoll on hsr.
Disable netpoll on hsr and replace the _irqsave() locking with _bh().
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Due to the hashed-MAC optimisation one problem become visible:
hsr_handle_sup_frame() walks over the list of available nodes and merges
two node entries into one if based on the information in the supervision
both MAC addresses belong to one node. The list-walk happens on a RCU
protected list and delete operation happens under a lock.
If the supervision arrives on both slave interfaces at the same time
then this delete operation can occur simultaneously on two CPUs. The
result is the first-CPU deletes the from the list and the second CPUs
BUGs while attempting to dereference a poisoned list-entry. This happens
more likely with the optimisation because a new node for the mac_B entry
is created once a packet has been received and removed (merged) once the
supervision frame has been received.
Avoid removing/ cleaning up a hsr_node twice by adding a `removed' field
which is set to true after the removal and checked before the removal.
Fixes: f266a683a4 ("net/hsr: Better frame dispatch")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
hsr_forward_skb() a skb and keeps information in an on-stack
hsr_frame_info. hsr_get_node() assigns hsr_frame_info::node_src which is
from a RCU list. This pointer is used later in hsr_forward_do().
I don't see a reason why this pointer can't vanish midway since there is
no guarantee that hsr_forward_skb() is invoked from an RCU read section.
Use rcu_read_lock() to protect hsr_frame_info::node_src from its
assignment until it is no longer used.
Fixes: f266a683a4 ("net/hsr: Better frame dispatch")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The hlist optimisation (which not only uses hlist_head instead of
list_head but also splits hsr_priv::node_db into an array of 256 slots)
does not consider the "node merge":
Upon starting the hsr network (with three nodes) a packet that is
sent from node1 to node3 will also be sent from node1 to node2 and then
forwarded to node3.
As a result node3 will receive 2 packets because it is not able
to filter out the duplicate. Each packet received will create a new
struct hsr_node with macaddress_A only set the MAC address it received
from (the two MAC addesses from node1).
At some point (early in the process) two supervision frames will be
received from node1. They will be processed by hsr_handle_sup_frame()
and one frame will leave early ("Node has already been merged") and does
nothing. The other frame will be merged as portB and have its MAC
address written to macaddress_B and the hsr_node (that was created for
it as macaddress_A) will be removed.
From now on HSR is able to identify a duplicate because both packets
sent from one node will result in the same struct hsr_node because
hsr_get_node() will find the MAC address either on macaddress_A or
macaddress_B.
Things get tricky with the optimisation: If sender's MAC address is
saved as macaddress_A then the lookup will work as usual. If the MAC
address has been merged into macaddress_B of another hsr_node then the
lookup won't work because it is likely that the data structure is in
another bucket. This results in creating a new struct hsr_node and not
recognising a possible duplicate.
A way around it would be to add another hsr_node::mac_list_B and attach
it to the other bucket to ensure that this hsr_node will be looked up
either via macaddress_A _or_ macaddress_B.
I however prefer to revert it because it sounds like an academic problem
rather than real life workload plus it adds complexity. I'm not an HSR
expert with what is usual size of a network but I would guess 40 to 60
nodes. With 10.000 nodes and assuming 60us for pass-through (from node
to node) then it would take almost 600ms for a packet to almost wrap
around which sounds a lot.
Revert the hash MAC addresses optimisation.
Fixes: 4acc45db71 ("net: hsr: use hlist_head instead of list_head for mac addresses")
Cc: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After commit 9ed7bfc795 ("sctp: fix memory leak in
sctp_stream_outq_migrate()"), sctp_sched_set_sched() is the only
place calling sched->free(), and it can actually be replaced by
sched->free_sid() on each stream, and yet there's already a loop
to traverse all streams in sctp_sched_set_sched().
This patch adds a function sctp_sched_free_sched() where it calls
sched->free_sid() for each stream to replace sched->free() calls
in sctp_sched_set_sched() and then deletes the unused free member
from struct sctp_sched_ops.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Link: https://lore.kernel.org/r/e10aac150aca2686cb0bd0570299ec716da5a5c0.1669849471.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds two new MPTCP netlink event types for PM listening
socket create and close, named MPTCP_EVENT_LISTENER_CREATED and
MPTCP_EVENT_LISTENER_CLOSED.
Add a new function mptcp_event_pm_listener() to push the new events
with family, port and addr to userspace.
Invoke mptcp_event_pm_listener() with MPTCP_EVENT_LISTENER_CREATED in
mptcp_listen() and mptcp_pm_nl_create_listen_socket(), invoke it with
MPTCP_EVENT_LISTENER_CLOSED in __mptcp_close_ssk().
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert BUG_ON() to WARN_ON_ONCE() and warn as well for unlikely
static key int overflow error-path.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the kernel was short on (atomic) memory and failed to allocate it -
don't proceed to creation of request socket. Otherwise the socket would
be unsigned and userspace likely doesn't expect that the TCP is not
MD5-signed anymore.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To do that, separate two scenarios:
- where it's the first MD5 key on the system, which means that enabling
of the static key may need to sleep;
- copying of an existing key from a listening socket to the request
socket upon receiving a signed TCP segment, where static key was
already enabled (when the key was added to the listening socket).
Now the life-time of the static branch for TCP-MD5 is until:
- last tcp_md5sig_info is destroyed
- last socket in time-wait state with MD5 key is closed.
Which means that after all sockets with TCP-MD5 keys are gone, the
system gets back the performance of disabled md5-key static branch.
While at here, provide static_key_fast_inc() helper that does ref
counter increment in atomic fashion (without grabbing cpus_read_lock()
on CONFIG_JUMP_LABEL=y). This is needed to add a new user for
a static_key when the caller controls the lifetime of another user.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a helper to allocate tcp_md5sig_info, that will help later to
do/allocate things when info allocated, once per socket.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ieee80211_drop_unencrypted is called from ieee80211_rx_h_mesh_fwding and
ieee80211_frame_allowed.
Since ieee80211_rx_h_mesh_fwding can forward packets for other mesh nodes
and is called earlier, it needs to check the decryptions status and if the
packet is using the control protocol on its own, instead of deferring to
the later call from ieee80211_frame_allowed.
Because of that, ieee80211_drop_unencrypted has a mesh specific check
that skips over the mesh header in order to check the payload protocol.
This code is invalid when called from ieee80211_frame_allowed, since that
happens after the 802.11->802.3 conversion.
Fix this by moving the mesh specific check directly into
ieee80211_rx_h_mesh_fwding.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20221201135730.19723-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can be used to selectively disable feature flags for checksum offload,
scatter/gather or GSO by changing vif->netdev_features.
Removing features from vif->netdev_features does not affect the netdev
features themselves, but instead fixes up skbs in the tx path so that the
offloads are not needed in the driver.
Aside from making it easier to deal with vif type based hardware limitations,
this also makes it possible to optimize performance on hardware without native
GSO support by declaring GSO support in hw->netdev_features and removing it
from vif->netdev_features. This allows mac80211 to handle GSO segmentation
after the sta lookup, but before itxq enqueue, thus reducing the number of
unnecessary sta lookups, as well as some other per-packet processing.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20221010094338.78070-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Updates to the TIM information element to match changes made in the
IEEE Std 802.11ah-2020.
Signed-off-by: Kieran Frewen <kieran.frewen@morsemicro.com>
Co-developed-by: Gilad Itzkovitch <gilad.itzkovitch@morsemicro.com>
Signed-off-by: Gilad Itzkovitch <gilad.itzkovitch@morsemicro.com>
Link: https://lore.kernel.org/r/20221106221602.25714-1-gilad.itzkovitch@morsemicro.com
[use skb_put_data/skb_put_u8]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It's not valid to have the multiple BSSID element in the
association response (per 802.11 REVme D1.0), so don't
try to parse it there, but only in the fallback beacon
elements if needed.
The other case that was parsing association requests was
already changed in a previous commit.
Change-Id: I659d2ef1253e079cc71c46a017044e116e31c024
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to open-code container_of() when we have
bss_from_pub(). Use it.
Change-Id: I074723717909ba211a40e6499f0c36df0e2ba4be
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The call to ieee80211_do_stop() right after will also do
synchronize_rcu() to ensure the SDATA_STATE_RUNNING bit
is cleared, so we don't need to synchronize_net() here.
Change-Id: Id9f9ffcf195002013e5d9fde288877d219780864
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_get_txq() can only be called with vif != NULL.
Remove not needed NULL test in function.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/20221107161328.2883-1-alexander@wetzel-home.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In regulatory_init_db(), when it's going to return a error, reg_pdev
should be unregistered. When load_builtin_regdb_keys() fails it doesn't
do it and makes cfg80211 can't be reload with report:
sysfs: cannot create duplicate filename '/devices/platform/regulatory.0'
...
<TASK>
dump_stack_lvl+0x79/0x9b
sysfs_warn_dup.cold+0x1c/0x29
sysfs_create_dir_ns+0x22d/0x290
kobject_add_internal+0x247/0x800
kobject_add+0x135/0x1b0
device_add+0x389/0x1be0
platform_device_add+0x28f/0x790
platform_device_register_full+0x376/0x4b0
regulatory_init+0x9a/0x4b2 [cfg80211]
cfg80211_init+0x84/0x113 [cfg80211]
...
Fixes: 90a53e4432 ("cfg80211: implement regdb signature checking")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Link: https://lore.kernel.org/r/20221109090237.214127-1-chenzhongjin@huawei.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the "channel->freq_offset" comparison is omitted in cmp_bss(),
BSS with different kHz units cannot be distinguished in the S1G Band.
So "freq_offset" should also be included in the comparison.
Signed-off-by: JUN-KYU SHIN <jk.shin@newratek.com>
Link: https://lore.kernel.org/r/20221111023301.6395-1-jk.shin@newratek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_lookup_key, the variable named `local` is unused if
compiled without lockdep, getting this warning:
net/mac80211/cfg.c: In function ‘ieee80211_lookup_key’:
net/mac80211/cfg.c:542:26: error: unused variable ‘local’ [-Werror=unused-variable]
struct ieee80211_local *local = sdata->local;
^~~~~
Fix it with __maybe_unused.
Fixes: 8cbf0c2ab6 ("wifi: mac80211: refactor some key code")
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Link: https://lore.kernel.org/r/20221111153622.29016-1-ihuguet@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For ACKs generated inside the I/O thread, transmit the ACK at the point of
generation. Where the ACK is generated outside of the I/O thread, it's
offloaded to the I/O thread to transmit it.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Fold __rxrpc_unuse_local() into rxrpc_unuse_local() as the latter is now
the only user of the former.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
When we've gone for >1RTT without transmitting a packet, we should reduce
the ssthresh and cut the cwnd by half (as suggested in RFC2861 sec 3.1).
However, we may receive ACK packets in a batch and the first of these may
cut the cwnd, preventing further transmission, and each subsequent one cuts
the cwnd yet further, reducing it to the floor and killing performance.
Fix this by moving the cwnd reset to after doing the transmission and
resetting the base time such that we don't cut the cwnd by half again for
at least another RTT.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Add a tracepoint to log when a cwnd reset occurs due to lack of
transmission on a call.
Add stat counters to count transmission underflows (ie. when we have tx
window space, but sendmsg doesn't manage to keep up), cwnd resets and
transmission failures.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
None of the spinlocks in rxrpc need a _bh annotation now as the RCU
callback routines no longer take spinlocks and the bulk of the packet
wrangling code is now run in the I/O thread, not softirq context.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Move the functions from the call->processor and local->processor work items
into the domain of the I/O thread.
The call event processor, now called from the I/O thread, then takes over
the job of cranking the call state machine, processing incoming packets and
transmitting DATA, ACK and ABORT packets. In a future patch,
rxrpc_send_ACK() will transmit the ACK on the spot rather than queuing it
for later transmission.
The call event processor becomes purely received-skb driven. It only
transmits things in response to events. We use "pokes" to queue a dummy
skb to make it do things like start/resume transmitting data. Timer expiry
also results in pokes.
The connection event processor, becomes similar, though crypto events, such
as dealing with CHALLENGE and RESPONSE packets is offloaded to a work item
to avoid doing crypto in the I/O thread.
The local event processor is removed and VERSION response packets are
generated directly from the packet parser. Similarly, ABORTs generated in
response to protocol errors will be transmitted immediately rather than
being pushed onto a queue for later transmission.
Changes:
========
ver #2)
- Fix a couple of introduced lock context imbalances.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Shay Drory
Ido Schimmel
ye xingchen
Jakub Kicinski
Kees Cook
Sudheer Mogilappagari
David S. Miller
Heiner Kallweit
Eric Dumazet
Jiri Pirko
Sebastian Andrzej Siewior
Xin Long
Geliang Tang
Dmitry Safonov
Felix Fietkau
Kieran Frewen
Johannes Berg
Alexander Wetzel
Chen Zhongjin
JUN-KYU SHIN
Íñigo Huguet
David Howells