Граф коммитов

614 Коммитов

Автор SHA1 Сообщение Дата
Niklas Söderlund cbf6d82cad mmc: core: add helper to see if a host is doing a retune
Add a helper to allow host drivers checking if a retune is in progress.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-10-08 11:40:43 +02:00
Ulf Hansson 29772f8a73 mmc: core: Drop the unused mmc_power_save|restore_host()
The last user of mmc_power_save|restore_host() APIs is gone, hence let's
drop them. Drop also the corresponding bus_ops callback,
->power_save|restore() as those becomes redundant.

Cc: Tony Lindgren <tony@atomide.com>
Cc: Eyal Reizer <eyalreizer@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-07-16 11:21:45 +02:00
Simon Horman ba6c7ac3a2 mmc: core: more fine-grained hooks for HS400 tuning
This adds two new HS400 tuning operations:
* hs400_downgrade
* hs400_complete

These supplement the existing HS400 operation:
* prepare_hs400_tuning

This is motivated by a requirement of Renesas SDHI for the following:
1. Disabling SCC before selecting to HS if selection of HS400 has occurred.
   This can be done in an implementation of prepare_hs400_tuning_downgrade
2. Updating registers after switching to HS400
   This can be done in an implementation of complete_hs400_tuning

If hs400_downgrade or hs400_complete are not implemented then they are not
called. Thus means there should be no affect for existing drivers as none
implemt these ops.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-07-16 11:21:45 +02:00
Shawn Lin a94a7483a9 mmc: core: Adjust and reuse the macro of R1_STATUS(x)
R1_STATUS(x) now is only used by ioctl_rpmb_card_status_poll(),
which checks all bits as possible. But according to the spec,
bit 17 and bit 18 should be ignored, as well bit 14 which is
reserved(must be set to 0) quoting from the spec and these rule
apply to all places checking the device status. So change
its checking from 0xFFFFE000 to 0xFFF9A000.

As a bonus, we reuse it for mmc_do_erase() as well as
mmc_switch_status_error().
(1) Currently mmc_switch_status_error() doesn't check bit 25, but
it means device is locked but not unlocked by CMD42 prior to any
operations which need check busy, which is also not allowed.
(2) mmc_do_erase() also forgot to to check bit 15, WP_ERASE_SKIP.
The spec says "Only partial address space was erased due to existing
write protected blocks.", which obviously means we should fail this I/O.
Otherwise, the partial erased data stored in nonvalatile flash violates
the data integrity from the view of I/O owner, which probably confuse
it when further used.

So reusing R1_STATUS for them not only improve the readability but also
slove real problems.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-07-16 11:21:45 +02:00
Linus Torvalds 1c8c5a9d38 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking updates from David Miller:

 1) Add Maglev hashing scheduler to IPVS, from Inju Song.

 2) Lots of new TC subsystem tests from Roman Mashak.

 3) Add TCP zero copy receive and fix delayed acks and autotuning with
    SO_RCVLOWAT, from Eric Dumazet.

 4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard
    Brouer.

 5) Add ttl inherit support to vxlan, from Hangbin Liu.

 6) Properly separate ipv6 routes into their logically independant
    components. fib6_info for the routing table, and fib6_nh for sets of
    nexthops, which thus can be shared. From David Ahern.

 7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP
    messages from XDP programs. From Nikita V. Shirokov.

 8) Lots of long overdue cleanups to the r8169 driver, from Heiner
    Kallweit.

 9) Add BTF ("BPF Type Format"), from Martin KaFai Lau.

10) Add traffic condition monitoring to iwlwifi, from Luca Coelho.

11) Plumb extack down into fib_rules, from Roopa Prabhu.

12) Add Flower classifier offload support to igb, from Vinicius Costa
    Gomes.

13) Add UDP GSO support, from Willem de Bruijn.

14) Add documentation for eBPF helpers, from Quentin Monnet.

15) Add TLS tx offload to mlx5, from Ilya Lesokhin.

16) Allow applications to be given the number of bytes available to read
    on a socket via a control message returned from recvmsg(), from
    Soheil Hassas Yeganeh.

17) Add x86_32 eBPF JIT compiler, from Wang YanQing.

18) Add AF_XDP sockets, with zerocopy support infrastructure as well.
    From Björn Töpel.

19) Remove indirect load support from all of the BPF JITs and handle
    these operations in the verifier by translating them into native BPF
    instead. From Daniel Borkmann.

20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha.

21) Allow XDP programs to do lookups in the main kernel routing tables
    for forwarding. From David Ahern.

22) Allow drivers to store hardware state into an ELF section of kernel
    dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy.

23) Various RACK and loss detection improvements in TCP, from Yuchung
    Cheng.

24) Add TCP SACK compression, from Eric Dumazet.

25) Add User Mode Helper support and basic bpfilter infrastructure, from
    Alexei Starovoitov.

26) Support ports and protocol values in RTM_GETROUTE, from Roopa
    Prabhu.

27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard
    Brouer.

28) Add lots of forwarding selftests, from Petr Machata.

29) Add generic network device failover driver, from Sridhar Samudrala.

* ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits)
  strparser: Add __strp_unpause and use it in ktls.
  rxrpc: Fix terminal retransmission connection ID to include the channel
  net: hns3: Optimize PF CMDQ interrupt switching process
  net: hns3: Fix for VF mailbox receiving unknown message
  net: hns3: Fix for VF mailbox cannot receiving PF response
  bnx2x: use the right constant
  Revert "net: sched: cls: Fix offloading when ingress dev is vxlan"
  net: dsa: b53: Fix for brcm tag issue in Cygnus SoC
  enic: fix UDP rss bits
  netdev-FAQ: clarify DaveM's position for stable backports
  rtnetlink: validate attributes in do_setlink()
  mlxsw: Add extack messages for port_{un, }split failures
  netdevsim: Add extack error message for devlink reload
  devlink: Add extack to reload and port_{un, }split operations
  net: metrics: add proper netlink validation
  ipmr: fix error path when ipmr_new_table fails
  ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds
  net: hns3: remove unused hclgevf_cfg_func_mta_filter
  netfilter: provide udp*_lib_lookup for nf_tproxy
  qed*: Utilize FW 8.37.2.0
  ...
2018-06-06 18:39:49 -07:00
yinbo.zhu a0d476654a mmc: sd: Define name for default speed dtr
Add a new define for the sd default speed 25MHz case

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-29 12:24:26 +02:00
Shawn Lin 6d796c68cd mmc: core: add tunable delay waiting for power to be stable
The hard-coded 10ms delay in mmc_power_up came from
commit 79bccc5aef ("mmc: increase power up delay"), which said "The TI
controller on Toshiba Tecra M5 needs more time to power up or the cards
will init incorrectly or not at all." But it's too engineering solution
for a special board but force all platforms to wait for that long time,
especially painful for mmc_power_up for eMMC when booting.

However, it's added since 2009, and we can't tell if other platforms
benefit from it. But in practise, the modern hardware are most likely to
have a stable power supply with 1ms after setting it for no matter PMIC
or discrete power. And more importnatly, most regulators implement the
callback of ->set_voltage_time_sel() for regulator core to wait for
specific period of time for the power supply to be stable, which means
once regulator_set_voltage_* return, the power should reach the the
minimum voltage that works for initialization. Of course, if there
are some other ways for host to power the card, we should allow them
to argue a suitable delay as well.

With this patch, we could assign the delay from firmware, or we could
assigne it via ->set_ios() callback from host drivers.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-21 10:38:50 +02:00
Sean Lanigan 9c4a121e82 brcmfmac: Add support for bcm43364 wireless chipset
Add support for the BCM43364 chipset via an SDIO interface, as used in
e.g. the Murata 1FX module.

The BCM43364 uses the same firmware as the BCM43430 (which is already
included), the only difference is the omission of Bluetooth.

However, the SDIO_ID for the BCM43364 is 02D0:A9A4, giving it a MODALIAS
of sdio:c00v02D0dA9A4, which doesn't get recognised and hence doesn't
load the brcmfmac module. Adding the 'A9A4' ID in the appropriate place
triggers the brcmfmac driver to load, and then correctly use the
firmware file 'brcmfmac43430-sdio.bin'.

Signed-off-by: Sean Lanigan <sean@lano.id.au>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-09 13:24:41 +03:00
Ulf Hansson 1433269c4d mmc: core: Export a function mmc_sw_reset() to allow soft reset of cards
It's rather common that a firmware is loaded into an SDIO func device
memory, by the corresponding SDIO func driver during ->probe() time.

However, to actually start running the new firmware, sometimes a soft reset
(no power cycle) and a re-initialization of the card is needed. This is for
example the case with the Espressif ESP8089 WiFi chips, when connected to
an SDIO interface.

To cope with this scenario, let's add a new exported function,
mmc_sw_reset(), which may be called when a soft reset and re-initialization
of the card are needed.

The mmc_sw_reset() is implemented on top of a new bus ops callback, similar
to how the mmc_hw_reset() has been implemented.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
2018-05-08 09:33:42 +02:00
Ulf Hansson 5581cfcdcc Merge branch 'sdhci_omap' into next
Merge immutable branch for sdhci-omap to add UHS/HS200 mode support.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-03 10:34:06 +02:00
Kishon Vijay Abraham I c16bc9a767 mmc: sdhci: Disable 1.8v modes (HS200/HS400/UHS) if controller can't support 1.8v
The SDHCI controller in a SoC might support HS200/HS400 (indicated
using mmc-hs200-1_8v/mmc-hs400-1_8v dt property), but if the board is
modeled such that the IO lines are not connected to 1.8v then
HS200/HS400 cannot be supported. Disable HS200/HS400 if the board
does not have 1.8v connected to the IO lines. Also Disable DDR/UHS in 1.8v
if the IO lines are not connected to 1.8v.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-03 09:36:19 +02:00
Kyle Roeschley 247cfe5355 mmc: core: Add capability to avoid 3.3V signaling
Some SD host controllers cannot handle extended use of 3.3V signaling.
To accommodate these controllers, add a capability that requires us to
negotiate the voltage down from 3.3V during card initialization.

Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Jennifer Dahm <jennifer.dahm@ni.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:44 +02:00
Diwakar Sharma 8ccd66f258 mmc: core: sdio: Set SDIO clock of SDR104 to 150MHz for Marvell 8887 chip
This patch uses limit clock rate quirk to reduce clock rate
for "SDR104" mode on IMX side for Marvell 8887
WiFi + Bluetooth chip side, as Marvell does not recommend
to use SDIO at the speed of higher than 150MHz.

Signed-off-by: Diwakar Sharma <diwakar.sharma@in.bosch.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:39 +02:00
harish_kandiga@mentor.com ebc5a1bf4f mmc: core: Add a new quirk for limiting clock rate
This patch adds a quirk to limit clock rate which
can be used to reduce the SDIO clock rate for some
chips with broken UHS.

Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:39 +02:00
Adrian Hunter 36f1d7e817 mmc: slot-gpio: Add a function to enable/disable card detect IRQ wakeup
Commit 03dbaa04a2 ("mmc: slot-gpio: Add support to enable irq wake on
cd_irq") enabled wakeup at initialization. However drivers may wish to
enable and disable based on different criteria. Add a helper function
mmc_gpio_set_cd_wake() to make it easy for drivers to do that.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-03-05 13:04:32 +01:00
Masahiro Yamada 85f9ef8cdf mmc: slot-gpio: add a helper to check capability of GPIO WP detection
Like mmc_can_gpio_cd(), mmc_can_gpio_ro() will also be useful for host
drivers to know whether GPIO write-protect detection is supported.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-01-18 09:08:56 +01:00
Adrian Hunter 126b627003 mmc: core: Remove code no longer needed after the switch to blk-mq
Remove code no longer needed after the switch to blk-mq.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-12-11 13:05:58 +01:00
Adrian Hunter 10f21df4a2 mmc: block: blk-mq: Add support for direct completion
For blk-mq, add support for completing requests directly in the ->done
callback. That means that error handling and urgent background operations
must be handled by recovery_work in that case.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-11 12:44:35 +01:00
Adrian Hunter c3d53d0da6 mmc: core: Add parameter use_blk_mq
Until mmc has blk-mq support fully implemented and tested, add a parameter
use_blk_mq, set to true if config option MMC_MQ_DEFAULT is selected, which
it is by default.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-11 12:44:33 +01:00
Linus Torvalds dee02770cd MMC core:
- Introduce host claiming by context to support blkmq
  - Preparations for enabling CQE (eMMC CMDQ) requests
  - Re-factorizations to prepare for blkmq support
  - Re-factorizations to prepare for CQE support
  - Fix signal voltage switch for SD cards without power cycle
  - Convert RPMB to a character device
  - Export eMMC revision via sysfs
  - Support eMMC DT binding for fixed driver type
  - Document mmc_regulator_get_supply() API
 
 MMC host:
  - omap_hsmmc: Updated regulator management for PBIAS
  - sdhci-omap: Add new OMAP SDHCI driver
  - meson-mx-sdio: New driver for the Amlogic Meson8 and Meson8b SoCs
  - sdhci-pci: Add support for Intel CDF
  - sdhci-acpi: Fix voltage switch for some Intel host controllers
  - sdhci-msm: Enable delay circuit calibration clocks
  - sdhci-msm: Manage power IRQ properly
  - mediatek: Add support of mt2701/mt2712
  - mediatek: Updates management of clocks and tunings
  - mediatek: Upgrade eMMC HS400 support
  - rtsx_pci: Update tuning for gen3 PCI-Express
  - renesas_sdhi: Support R-Car Gen[123] fallback compatibility strings
  - Catch all errors when getting regulators
  - Various additional improvements and cleanups
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJaCXiaAAoJEP4mhCVzWIwp+c4P/3UptZJJScU4WFS1zXH8h/YK
 mYQ4DOCZqQYihKV4ssbAAjmTkT3RdMkl+rq2s5+ZfVbsu57UqeHNaNXBQWirkXCo
 xBDzZlZFz42g4apKq+ZfmewZTM2fjed8Z7SrDcxPkkyU90QKa/LFFleAyxyXxXr1
 ubKHJtev/oWBRxvzvWPYNUI5ExraxGxp2iGvavoYHNcggAgOSBJoKESvF7er5MRK
 Cx5cuKAESU2dJFQnebjndx3dFgQsZ18RTRXUom50oP3BXF2G3gIBMjxp9VfyuOGV
 xedyE2ALQxr1bxyWWejMdhhiZ+eNZNtiEJKqJ37ArTeBDyDfO/SDVXlkqkAARlYW
 rTzh9olfbuhFdCAo2gxAcCaQXnjgQzDDKnQJs++tQVziXGI9ezc44+A6fNh39nre
 yc/MLIjN96vWRhhFuTeFuENN+n7D2xyy+keXZXrALYYOCPAlKtip6DOgVl3ltNvx
 K1O7/STqdR4OHLK6vgdzi9ai3PmcmSBQwKCqqCH/7mcFm1xtBcxqdrEwORLQ3lCH
 c/tl4lJqJR2BD8U9gipjik0ovWb5p2KKAYhjqEY2qMy14OXs2509Y8GcqQRzqcQc
 FSAfUInooHfDEbUBVsLpTOjMvd6LAx34fTJ9QAanAZ1wdeV8C9DRz3kJh/L/mOmG
 N7/jyJnMV1Izknmpc2MP
 =3Gvx
 -----END PGP SIGNATURE-----

Merge tag 'mmc-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Introduce host claiming by context to support blkmq
   - Preparations for enabling CQE (eMMC CMDQ) requests
   - Re-factorizations to prepare for blkmq support
   - Re-factorizations to prepare for CQE support
   - Fix signal voltage switch for SD cards without power cycle
   - Convert RPMB to a character device
   - Export eMMC revision via sysfs
   - Support eMMC DT binding for fixed driver type
   - Document mmc_regulator_get_supply() API

 MMC host:
   - omap_hsmmc: Updated regulator management for PBIAS
   - sdhci-omap: Add new OMAP SDHCI driver
   - meson-mx-sdio: New driver for the Amlogic Meson8 and Meson8b SoCs
   - sdhci-pci: Add support for Intel CDF
   - sdhci-acpi: Fix voltage switch for some Intel host controllers
   - sdhci-msm: Enable delay circuit calibration clocks
   - sdhci-msm: Manage power IRQ properly
   - mediatek: Add support of mt2701/mt2712
   - mediatek: Updates management of clocks and tunings
   - mediatek: Upgrade eMMC HS400 support
   - rtsx_pci: Update tuning for gen3 PCI-Express
   - renesas_sdhi: Support R-Car Gen[123] fallback compatibility strings
   - Catch all errors when getting regulators
   - Various additional improvements and cleanups"

* tag 'mmc-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (91 commits)
  sdhci-fujitsu: add support for setting the CMD_DAT_DELAY attribute
  dt-bindings: sdhci-fujitsu: document cmd-dat-delay property
  mmc: tmio: Replace msleep() of 20ms or less with usleep_range()
  mmc: dw_mmc: Convert timers to use timer_setup()
  mmc: dw_mmc: Cleanup the DTO timer like the CTO one
  mmc: vub300: Use common code in __download_offload_pseudocode()
  mmc: tmio: Use common error handling code in tmio_mmc_host_probe()
  mmc: Convert timers to use timer_setup()
  mmc: sdhci-acpi: Fix voltage switch for some Intel host controllers
  mmc: sdhci-acpi: Let devices define their own private data
  mmc: mediatek: perfer to use rise edge latching for cmd line
  mmc: mediatek: improve eMMC hs400 mode read performance
  mmc: mediatek: add latch-ck support
  mmc: mediatek: add support of source_cg clock
  mmc: mediatek: add stop_clk fix and enhance_rx support
  mmc: mediatek: add busy_check support
  mmc: mediatek: add async fifo and data tune support
  mmc: mediatek: add pad_tune0 support
  mmc: mediatek: make hs400_tune_response only for mt8173
  arm64: dts: mt8173: remove "mediatek, mt8135-mmc" from mmc nodes
  ...
2017-11-13 10:17:35 -08:00
Greg Kroah-Hartman b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00
Wolfram Sang 6186d06c51 mmc: parse new binding for eMMC fixed driver type
Parse the new binding and store it in the host struct after doing some
sanity checks. The code is designed to support fixed SD driver type if
we ever need that.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-10-30 11:50:38 +01:00
Adrian Hunter 72a5af554d mmc: core: Add support for handling CQE requests
Add core support for handling CQE requests, including starting, completing
and recovering.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-10-30 11:45:50 +01:00
Adrian Hunter 6c0cedd1ef mmc: core: Introduce host claiming by context
Currently the host can be claimed by a task.  Change this so that the host
can be claimed by a context that may or may not be a task.  This provides
for the host to be claimed by a block driver queue to support blk-mq, while
maintaining compatibility with the existing use of mmc_claim_host().

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-10-30 11:45:49 +01:00
Wolfram Sang 79ea73b05a mmc: sdhci-pci: remove outdated declaration
The function was removed half a year ago, so this declaration can go,
too.

Fixes: 51ced59cc0 ("mmc: sdhci-pci: Use ACPI DSM to get driver strength for some Intel devices")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-10-30 11:40:08 +01:00
Linus Walleij de3ee99b09 mmc: Delete bounce buffer handling
In may, Steven sent a patch deleting the bounce buffer handling
and the CONFIG_MMC_BLOCK_BOUNCE option.

I chose the less invasive path of making it a runtime config
option, and we merged that successfully for kernel v4.12.

The code is however just standing in the way and taking up
space for seemingly no gain on any systems in wide use today.

Pierre says the code was there to improve speed on TI SDHCI
controllers on certain HP laptops and possibly some Ricoh
controllers as well. Early SDHCI controllers lacked the
scatter-gather feature, which made software bounce buffers
a significant speed boost.

We are clearly talking about the list of SDHCI PCI-based
MMC/SD card readers found in the pci_ids[] list in
drivers/mmc/host/sdhci-pci-core.c.

The TI SDHCI derivative is not supported by the upstream
kernel. This leaves the Ricoh.

What we can however notice is that the x86 defconfigs in the
kernel did not enable CONFIG_MMC_BLOCK_BOUNCE option, which
means that any such laptop would have to have a custom
configured kernel to actually take advantage of this
bounce buffer speed-up. It simply seems like there was
a speed optimization for the Ricoh controllers that noone
was using. (I have not checked the distro defconfigs but
I am pretty sure the situation is the same there.)

Bounce buffers increased performance on the OMAP HSMMC
at one point, and was part of the original submission in
commit a45c6cb816 ("[ARM] 5369/1: omap mmc: Add new
   omap hsmmc controller for 2430 and 34xx, v3")

This optimization was removed in
commit 0ccd76d4c2 ("omap_hsmmc: Implement scatter-gather
   emulation")
which found that scatter-gather emulation provided even
better performance.

The same was introduced for SDHCI in
commit 2134a922c6 ("sdhci: scatter-gather (ADMA) support")

I am pretty positively convinced that software
scatter-gather emulation will do for any host controller what
the bounce buffers were doing. Essentially, the bounce buffer
was a reimplementation of software scatter-gather-emulation in
the MMC subsystem, and it should be done away with.

Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Juha Yrjola <juha.yrjola@solidboot.com>
Cc: Steven J. Hill <Steven.Hill@cavium.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Suggested-by: Steven J. Hill <Steven.Hill@cavium.com>
Suggested-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-10-04 10:22:55 +02:00
Linus Torvalds 15d8ffc964 MMC core:
- Continue to refactor the mmc block code to prepare for blkmq
  - Move mmc block debugfs into block module
  - Next step for eMMC CMDQ by adding a new mmc host interface for it
  - Move Kconfig option MMC_DEBUG from core to host
  - Some additional minor improvements
 
 MMC host:
  - Declare structs as const when applicable
  - Explicitly request exclusive reset control when applicable
  - Improve some error paths and other various cleanups
  - sdhci: Preparations to support SDHCI OMAP
  - sdhci: Improve some PM related code
  - sdhci: Re-factoring and modernizations
  - sdhci-xenon: Add runtime PM and system sleep support
  - sdhci-xenon: Add support for eMMC HS400 Enhanced Strobe
  - sdhci-cadence: Add system sleep support
  - sdhci-of-at91: Improve system sleep support
  - dw_mmc: Add support for Hisilicon hi3660
  - sunxi: Add support for A83T eMMC
  - sunxi: Add support for DDR52 mode
  - meson-gx: Add support for UHS-I SD-cards
  - meson-gx: Cleanups and improvements
  - tmio: Fix CMD12 (STOP) handling
  - tmio: Cleanups and improvements
  - renesas_sdhi: Add r8a7743/5 support
  - renesas-sdhi: Add support for R-Car Gen3 SDHI DMAC
  - renesas_sdhi: Cleanups and improvements
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJZr7CEAAoJEP4mhCVzWIwp5WQQAK9l2Hg1k4tFzxQ5EmKB/9Sm
 r3eS2GrosqrsCffR3vSSKnmva/lOrQuBzhqzx1MvWAByMUc5w8Yc8OowrKGhCWm9
 pAzi/3Tnjf7A9nAq+0NeGhkwybckam9ZpGhMyC1E4bp63g6PCoHjTcqOMVnjYxHz
 cUNNQUz7oCjW6tjtpvdJQWZuIGiScNuyxrTYKi8SUpQZ0LQo8nU9DujKcwsKsZed
 gYEIimqOqZnGz1rWs/EP2Y5TSoPVxvnb6nc90gt8kh0nfXYumxKjEmHZ0PB7K97b
 pioCN/THtkDgdYn8j3gnDXZYYa6JA4fKKOw+S6VZraLoVLeDtLo5zK353Rr3BscI
 SddxLePp5WclRal+WulLLJs1FeY5PN3ji+mxC3FAG6cvCqIyosyU8HKG79Lhwwl6
 7qlaDf27BhK71Sf17jzxtc5OwVTkSsY+9iKzVZAw5tIHSLR+nwhjM2vlAVU+oG2r
 KAsuVO1CVAqYbeIBJ85R6bPzgRGxQ0Kmkqwxe1QDVhgXl3eC5Ot5N/bOifv7HzV+
 m+6W1Wdw6/tUKD5g5c6s2WMijXgTdEnfj7dYXmHHN4q1abAKj0cOVjXtmVb90DHM
 5tvfxNurQZCCLo2A88/BYXRd299vBzOy9HAWvMvt5effQfxgFfpC1gc9NkfUTfkA
 FTOQ96vOpOmAH5uA0Xvm
 =850Z
 -----END PGP SIGNATURE-----

Merge tag 'mmc-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Continue to refactor the mmc block code to prepare for blkmq
   - Move mmc block debugfs into block module
   - Next step for eMMC CMDQ by adding a new mmc host interface for it
   - Move Kconfig option MMC_DEBUG from core to host
   - Some additional minor improvements

  MMC host:
   - Declare structs as const when applicable
   - Explicitly request exclusive reset control when applicable
   - Improve some error paths and other various cleanups
   - sdhci: Preparations to support SDHCI OMAP
   - sdhci: Improve some PM related code
   - sdhci: Re-factoring and modernizations
   - sdhci-xenon: Add runtime PM and system sleep support
   - sdhci-xenon: Add support for eMMC HS400 Enhanced Strobe
   - sdhci-cadence: Add system sleep support
   - sdhci-of-at91: Improve system sleep support
   - dw_mmc: Add support for Hisilicon hi3660
   - sunxi: Add support for A83T eMMC
   - sunxi: Add support for DDR52 mode
   - meson-gx: Add support for UHS-I SD-cards
   - meson-gx: Cleanups and improvements
   - tmio: Fix CMD12 (STOP) handling
   - tmio: Cleanups and improvements
   - renesas_sdhi: Add r8a7743/5 support
   - renesas-sdhi: Add support for R-Car Gen3 SDHI DMAC
   - renesas_sdhi: Cleanups and improvements"

* tag 'mmc-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (145 commits)
  mmc: renesas_sdhi: Add r8a7743/5 support
  mmc: meson-gx: fix __ffsdi2 undefined on arm32
  mmc: sdhci-xenon: add runtime pm support and reimplement standby
  mmc: core: Move mmc_start_areq() declaration
  mmc: mmci: stop building qcom dml as module
  mmc: sunxi: Reset the device at probe time
  clk: sunxi-ng: Provide a default reset hook
  mmc: meson-gx: rework tuning function
  mmc: meson-gx: change default tx phase
  mmc: meson-gx: implement voltage switch callback
  mmc: meson-gx: use CCF to handle the clock phases
  mmc: meson-gx: implement card_busy callback
  mmc: meson-gx: simplify interrupt handler
  mmc: meson-gx: work around clk-stop issue
  mmc: meson-gx: fix dual data rate mode frequencies
  mmc: meson-gx: rework clock init function
  mmc: meson-gx: rework clk_set function
  mmc: meson-gx: rework set_ios function
  mmc: meson-gx: cfg init overwrite values
  mmc: meson-gx: initialize sane clk default before clock register
  ...
2017-09-07 12:24:50 -07:00
Adrian Hunter 906d5ff618 mmc: core: Move mmc_start_areq() declaration
mmc_start_areq() is an internal mmc core API. Move the declaration
accordingly.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-08-30 15:03:53 +02:00
Adrian Hunter d3bf68ae04 mmc: host: Add CQE interface
Add CQE host operations, capabilities, and host members.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-08-30 15:03:33 +02:00
Adrian Hunter d2f82254e4 mmc: core: Add members to mmc_request and mmc_data for CQE's
Most of the information needed to issue requests to a CQE is already in
struct mmc_request and struct mmc_data. Add data block address, some flags,
and the task id (tag), and allow for cmd being NULL which it is for CQE
tasks.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-08-30 14:02:01 +02:00
Adrian Hunter dc8d68bb6c mmc: core: Remove unused MMC_CAP2_PACKED_CMD
Packed commands support was removed but some bits got left behind. Remove
them.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-08-30 14:02:00 +02:00
Shawn Lin 4406ae215b mmc: core: correct taac parameter according to the specification
Per the spec of JESD84-B51, section 7.3, replace tacc with taac to
fix the obvious typo.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-08-30 14:01:46 +02:00
Shawn Lin 1896f14006 mmc: core: remove check of host->removed for rescan routine
The intention of this check was to prevent the conflict between
hotplug and removing driver for whatever reason. Currently it
doesn't improve anything and the following rescan process could
still saftly perform the scan flow. So these code seems pointless
now and let's remove them.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-08-30 14:01:33 +02:00
Chi-Hsien Lin 0ec9eb90fe brcmfmac: Add support for CYW4373 SDIO/USB chipset
Add support for CYW4373 SDIO/USB chipset.
CYW4373 is a 1x1 dual-band 11ac chipset with 20/40/80Mhz channel support.
It's a WiFi/BT combo device.

Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-08-08 14:51:12 +03:00
Adrian Hunter 03dbaa04a2 mmc: slot-gpio: Add support to enable irq wake on cd_irq
Add host capability MMC_CAP_CD_WAKE to enable irq wake on the card detect
irq.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-06-20 10:30:49 +02:00
Ulf Hansson d2a47176a8 mmc: core: Remove MMC_CAP2_HC_ERASE_SZ
The MMC_CAP2_HC_ERASE_SZ is used only by a few mmc host drivers. Its intent
is to enable eMMC's high-capacity erase size, as to improve the behaviour
of the erase operations.

We should strive to avoid software configuration options that aren't
necessary, but instead deploy common behaviours. For these reasons, let's
remove the capability bit for MMC_CAP2_HC_ERASE_SZ and make it the default
behaviour.

Note that this change doesn't affect eMMCs supporting trim/discard, because
these commands operates on sectors and takes precedence over erase
commands.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
2017-06-20 10:30:48 +02:00
Linus Walleij 304419d8a7 mmc: core: Allocate per-request data using the block layer core
The mmc_queue_req is a per-request state container the MMC core uses
to carry bounce buffers, pointers to asynchronous requests and so on.
Currently allocated as a static array of objects, then as a request
comes in, a mmc_queue_req is assigned to it, and used during the
lifetime of the request.

This is backwards compared to how other block layer drivers work:
they usally let the block core provide a per-request struct that get
allocated right beind the struct request, and which can be obtained
using the blk_mq_rq_to_pdu() helper. (The _mq_ infix in this function
name is misleading: it is used by both the old and the MQ block
layer.)

The per-request struct gets allocated to the size stored in the queue
variable .cmd_size initialized using the .init_rq_fn() and
cleaned up using .exit_rq_fn().

The block layer code makes the MMC core rely on this mechanism to
allocate the per-request mmc_queue_req state container.

Doing this make a lot of complicated queue handling go away. We only
need to keep the .qnct that keeps count of how many request are
currently being processed by the MMC layer. The MQ block layer will
replace also this once we transition to it.

Doing this refactoring is necessary to move the ioctl() operations
into custom block layer requests tagged with REQ_OP_DRV_[IN|OUT]
instead of the custom code using the BigMMCHostLock that we have
today: those require that per-request data be obtainable easily from
a request after creating a custom request with e.g.:

struct request *rq = blk_get_request(q, REQ_OP_DRV_IN, __GFP_RECLAIM);
struct mmc_queue_req *mq_rq = req_to_mq_rq(rq);

And this is not possible with the current construction, as the request
is not immediately assigned the per-request state container, but
instead it gets assigned when the request finally enters the MMC
queue, which is way too late for custom requests.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[Ulf: Folded in the fix to drop a call to blk_cleanup_queue()]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Heiner Kallweit <hkallweit1@gmail.com>
2017-06-20 10:30:17 +02:00
Linus Walleij c3dccb74be mmc: core: Delete bounce buffer Kconfig option
This option is activated by all multiplatform configs and what
not so we almost always have it turned on, and the memory it
saves is negligible, even more so moving forward. The actual
bounce buffer only gets allocated only when used, the only
thing the ifdefs are saving is a little bit of code.

It is highly improper to have this as a Kconfig option that
get turned on by Kconfig, make this a pure runtime-thing and
let the host decide whether we use bounce buffers. We add a
new property "disable_bounce" to the host struct.

Notice that mmc_queue_calc_bouncesz() already disables the
bounce buffers if host->max_segs != 1, so any arch that has a
maximum number of segments higher than 1 will have bounce
buffers disabled.

The option CONFIG_MMC_BLOCK_BOUNCE is default y so the
majority of platforms in the kernel already have it on, and
it then gets turned off at runtime since most of these have
a host->max_segs > 1. The few exceptions that have
host->max_segs == 1 and still turn off the bounce buffering
are those that disable it in their defconfig.

Those are the following:

arch/arm/configs/colibri_pxa300_defconfig
arch/arm/configs/zeus_defconfig
- Uses MMC_PXA, drivers/mmc/host/pxamci.c
- Sets host->max_segs = NR_SG, which is 1
- This needs its bounce buffer deactivated so we set
  host->disable_bounce to true in the host driver

arch/arm/configs/davinci_all_defconfig
- Uses MMC_DAVINCI, drivers/mmc/host/davinci_mmc.c
- This driver sets host->max_segs to MAX_NR_SG, which is 16
- That means this driver anyways disabled bounce buffers
- No special action needed for this platform

arch/arm/configs/lpc32xx_defconfig
arch/arm/configs/nhk8815_defconfig
arch/arm/configs/u300_defconfig
- Uses MMC_ARMMMCI, drivers/mmc/host/mmci.[c|h]
- This driver by default sets host->max_segs to NR_SG,
  which is 128, unless a DMA engine is used, and in that case
  the number of segments are also > 1
- That means this driver already disables bounce buffers
- No special action needed for these platforms

arch/arm/configs/sama5_defconfig
- Uses MMC_SDHCI, MMC_SDHCI_PLTFM, MMC_SDHCI_OF_AT91, MMC_ATMELMCI
- Uses drivers/mmc/host/sdhci.c
- Normally sets host->max_segs to SDHCI_MAX_SEGS which is 128 and
  thus disables bounce buffers
- Sets host->max_segs to 1 if SDHCI_USE_SDMA is set
- SDHCI_USE_SDMA is only set by SDHCI on PCI adapers
- That means that for this platform bounce buffers are already
  disabled at runtime
- No special action needed for this platform

arch/blackfin/configs/CM-BF533_defconfig
arch/blackfin/configs/CM-BF537E_defconfig
- Uses MMC_SPI (a simple MMC card connected on SPI pins)
- Uses drivers/mmc/host/mmc_spi.c
- Sets host->max_segs to MMC_SPI_BLOCKSATONCE which is 128
- That means this platform already disables bounce buffers at
  runtime
- No special action needed for these platforms

arch/mips/configs/cavium_octeon_defconfig
- Uses MMC_CAVIUM_OCTEON, drivers/mmc/host/cavium.c
- Sets host->max_segs to 16 or 1
- Setting host->disable_bounce to be sure for the 1 case

arch/mips/configs/qi_lb60_defconfig
- Uses MMC_JZ4740, drivers/mmc/host/jz4740_mmc.c
- This sets host->max_segs to 128 so bounce buffers are
  already runtime disabled
- No action needed for this platform

It would be interesting to come up with a list of the platforms
that actually end up using bounce buffers. I have not been
able to infer such a list, but it occurs when
host->max_segs == 1 and the bounce buffering is not explicitly
disabled.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-06-20 10:30:17 +02:00
Ulf Hansson 682696605c mmc: sdio: Add API to manage SDIO IRQs from a workqueue
For hosts not supporting MMC_CAP2_SDIO_IRQ_NOTHREAD but MMC_CAP_SDIO_IRQ,
the SDIO IRQs are processed from a dedicated kernel thread. For these
cases, the host calls mmc_signal_sdio_irq() from its ISR to signal a new
SDIO IRQ.

Signaling an SDIO IRQ makes the host's ->enable_sdio_irq() callback to be
invoked to temporary disable the IRQs, before the kernel thread is woken up
to process it. When processing of the IRQs are completed, they are
re-enabled by the kernel thread, again via invoking the host's
->enable_sdio_irq().

The observation from this, is that the execution path is being unnecessary
complex, as the host driver already knows that it needs to temporary
disable the IRQs before signaling a new one. Moreover, replacing the kernel
thread with a work/workqueue would not only greatly simplify the code, but
also make it more robust.

To address the above problems, let's continue to build upon the support for
MMC_CAP2_SDIO_IRQ_NOTHREAD, as it already implements SDIO IRQs to be
processed without using the clumsy kernel thread and without the ping-pong
calls of the host's ->enable_sdio_irq() callback for each processed IRQ.

Therefore, let's add new API sdio_signal_irq(), which enables hosts to
signal/process SDIO IRQs by using a work/workqueue, rather than using the
kernel thread.

Add also a new host callback ->ack_sdio_irq(), which the work invokes when
the SDIO IRQs have been processed. This informs the host about when it
shall re-enable the SDIO IRQs. Potentially, we could re-use the existing
->enable_sdio_irq() callback instead of adding a new one, however it has
turned out that it's more convenient for hosts to get this information via
a separate callback.

Hosts that wants to use this new method to signal/process SDIO IRQs, must
enable MMC_CAP2_SDIO_IRQ_NOTHREAD and implement the ->ack_sdio_irq()
callback.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
2017-06-20 10:30:11 +02:00
Ulf Hansson 33e6d74d65 mmc: core: Export API to allow hosts to get the card address
Some hosts controllers, like Cavium, needs to know whether the card
operates in byte- or block-address mode. Therefore export a new API,
mmc_card_is_blockaddr(), which provides this information.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Steven J. Hill <Steven.Hill@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
2017-04-24 21:49:15 +02:00
Adrian Hunter 9d4579a85c mmc: mmc_test: Disable Command Queue while mmc_test is used
Normal read and write commands may not be used while the command queue is
enabled. Disable the Command Queue when mmc_test is probed and re-enable it
when it is removed.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Harjani Ritesh <riteshh@codeaurora.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-04-24 21:42:02 +02:00
Adrian Hunter b658af7184 mmc: mmc: Add functions to enable / disable the Command Queue
Add helper functions to enable or disable the Command Queue.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-04-24 21:42:02 +02:00
Adrian Hunter 7b410d074b mmc: queue: Share mmc request array between partitions
eMMC can have multiple internal partitions that are represented as separate
disks / queues. However switching between partitions is only done when the
queue is empty. Consequently the array of mmc requests that are queued can
be shared between partitions saving memory.

Keep a pointer to the mmc request queue on the card, and use that instead
of allocating a new one for each partition.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-04-24 21:42:01 +02:00
Heiner Kallweit 6335d68349 mmc: core: add mmc_get_dma_dir
Add function for determining DMA direction to core.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-04-24 21:41:52 +02:00
Heiner Kallweit 5ef1ecf060 mmc: sdio: fix alignment issue in struct sdio_func
Certain 64-bit systems (e.g. Amlogic Meson GX) require buffers to be
used for DMA to be 8-byte-aligned. struct sdio_func has an embedded
small DMA buffer not meeting this requirement.
When testing switching to descriptor chain mode in meson-gx driver
SDIO is broken therefore. Fix this by allocating the small DMA buffer
separately as kmalloc ensures that the returned memory area is
properly aligned for every basic data type.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-04-18 19:18:07 +02:00
Linus Torvalds 3051bf36c2 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking updates from David Miller:
 "Highlights:

   1) Support TX_RING in AF_PACKET TPACKET_V3 mode, from Sowmini
      Varadhan.

   2) Simplify classifier state on sk_buff in order to shrink it a bit.
      From Willem de Bruijn.

   3) Introduce SIPHASH and it's usage for secure sequence numbers and
      syncookies. From Jason A. Donenfeld.

   4) Reduce CPU usage for ICMP replies we are going to limit or
      suppress, from Jesper Dangaard Brouer.

   5) Introduce Shared Memory Communications socket layer, from Ursula
      Braun.

   6) Add RACK loss detection and allow it to actually trigger fast
      recovery instead of just assisting after other algorithms have
      triggered it. From Yuchung Cheng.

   7) Add xmit_more and BQL support to mvneta driver, from Simon Guinot.

   8) skb_cow_data avoidance in esp4 and esp6, from Steffen Klassert.

   9) Export MPLS packet stats via netlink, from Robert Shearman.

  10) Significantly improve inet port bind conflict handling, especially
      when an application is restarted and changes it's setting of
      reuseport. From Josef Bacik.

  11) Implement TX batching in vhost_net, from Jason Wang.

  12) Extend the dummy device so that VF (virtual function) features,
      such as configuration, can be more easily tested. From Phil
      Sutter.

  13) Avoid two atomic ops per page on x86 in bnx2x driver, from Eric
      Dumazet.

  14) Add new bpf MAP, implementing a longest prefix match trie. From
      Daniel Mack.

  15) Packet sample offloading support in mlxsw driver, from Yotam Gigi.

  16) Add new aquantia driver, from David VomLehn.

  17) Add bpf tracepoints, from Daniel Borkmann.

  18) Add support for port mirroring to b53 and bcm_sf2 drivers, from
      Florian Fainelli.

  19) Remove custom busy polling in many drivers, it is done in the core
      networking since 4.5 times. From Eric Dumazet.

  20) Support XDP adjust_head in virtio_net, from John Fastabend.

  21) Fix several major holes in neighbour entry confirmation, from
      Julian Anastasov.

  22) Add XDP support to bnxt_en driver, from Michael Chan.

  23) VXLAN offloads for enic driver, from Govindarajulu Varadarajan.

  24) Add IPVTAP driver (IP-VLAN based tap driver) from Sainath Grandhi.

  25) Support GRO in IPSEC protocols, from Steffen Klassert"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1764 commits)
  Revert "ath10k: Search SMBIOS for OEM board file extension"
  net: socket: fix recvmmsg not returning error from sock_error
  bnxt_en: use eth_hw_addr_random()
  bpf: fix unlocking of jited image when module ronx not set
  arch: add ARCH_HAS_SET_MEMORY config
  net: napi_watchdog() can use napi_schedule_irqoff()
  tcp: Revert "tcp: tcp_probe: use spin_lock_bh()"
  net/hsr: use eth_hw_addr_random()
  net: mvpp2: enable building on 64-bit platforms
  net: mvpp2: switch to build_skb() in the RX path
  net: mvpp2: simplify MVPP2_PRS_RI_* definitions
  net: mvpp2: fix indentation of MVPP2_EXT_GLOBAL_CTRL_DEFAULT
  net: mvpp2: remove unused register definitions
  net: mvpp2: simplify mvpp2_bm_bufs_add()
  net: mvpp2: drop useless fields in mvpp2_bm_pool and related code
  net: mvpp2: remove unused 'tx_skb' field of 'struct mvpp2_tx_queue'
  net: mvpp2: release reference to txq_cpu[] entry after unmapping
  net: mvpp2: handle too large value in mvpp2_rx_time_coal_set()
  net: mvpp2: handle too large value handling in mvpp2_rx_pkts_coal_set()
  net: mvpp2: remove useless arguments in mvpp2_rx_{pkts, time}_coal_set
  ...
2017-02-22 10:15:09 -08:00
Shawn Lin 884f386078 mmc: core: move some sdio IDs out of quirks file
Consolidate all the sdio devices' IDs into sdio_ids.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-15 11:34:26 +01:00
Uri Yanai efff8e7879 mmc: Adding AUTO_BKOPS_EN bit set for Auto BKOPS support
Adding dedicated flag for AUTO_BKOPS in card->ext_csd structure.
Read AUTO_BKOPS bit value from the device EXT_CSD and set to the
card->ext_csd structure.
In mmc_decode_ext_csd() add a print message in case the AUTO_BKOPS
is enabled

Signed-off-by: Uri Yanai <uri.yanai@sandisk.com>
Signed-off-by: Alex Lemberg <alex.lemberg@sandisk.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-14 09:11:00 +01:00
Linus Walleij c3399ef55d mmc: core: rename mmc_start_req() to *areq()
With the coexisting __mmc_start_request(), mmc_start_request()
and __mmc_start_req() it is a bit confusing that mmc_start_req()
actually does not start a normal request, but an asynchronous
request.

Rename it to mmc_start_areq() to make it explicit what the
function is doing, also fix the kerneldoc for this function
while we're at it.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:20:58 +01:00
Ulf Hansson 20f921bb01 mmc: core: Invent MMC_CAP_3_3V_DDR
According the JEDEC specification an eMMC card supporting 1.8V vccq in DDR
mode should also be capable of 3.3V. However, it's been reported that some
mmc hosts supports 3.3V, but not 1.8V.

Currently the mmc core implements an error handling when the host fails to
set 1.8V for vccq, by falling back to 3.3V. Unfortunate, this seems to be
insufficient for some mmc hosts. To enable these to use eMMC DDR mode let's
invent a new mmc cap, MMC_CAP_3_3V_DDR, which tells whether they support
the eMMC 3.3V DDR mode.

In case MMC_CAP_3_3V_DDR is set, but not MMC_CAP_1_8V_DDR, let's change to
remain on the 3.3V, as it's the default voltage level for vccq, set by the
earlier power up sequence.

As this change introduces MMC_CAP_3_3V_DDR, let's take the opportunity to
do some re-formatting of the related defines in the header file.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
2017-02-13 13:20:44 +01:00