Граф коммитов

134 Коммитов

Автор SHA1 Сообщение Дата
Johannes Weiner 4b85afbdac mm: zero-seek shrinkers
The page cache and most shrinkable slab caches hold data that has been
read from disk, but there are some caches that only cache CPU work, such
as the dentry and inode caches of procfs and sysfs, as well as the subset
of radix tree nodes that track non-resident page cache.

Currently, all these are shrunk at the same rate: using DEFAULT_SEEKS for
the shrinker's seeks setting tells the reclaim algorithm that for every
two page cache pages scanned it should scan one slab object.

This is a bogus setting.  A virtual inode that required no IO to create is
not twice as valuable as a page cache page; shadow cache entries with
eviction distances beyond the size of memory aren't either.

In most cases, the behavior in practice is still fine.  Such virtual
caches don't tend to grow and assert themselves aggressively, and usually
get picked up before they cause problems.  But there are scenarios where
that's not true.

Our database workloads suffer from two of those.  For one, their file
workingset is several times bigger than available memory, which has the
kernel aggressively create shadow page cache entries for the non-resident
parts of it.  The workingset code does tell the VM that most of these are
expendable, but the VM ends up balancing them 2:1 to cache pages as per
the seeks setting.  This is a huge waste of memory.

These workloads also deal with tens of thousands of open files and use
/proc for introspection, which ends up growing the proc_inode_cache to
absurdly large sizes - again at the cost of valuable cache space, which
isn't a reasonable trade-off, given that proc inodes can be re-created
without involving the disk.

This patch implements a "zero-seek" setting for shrinkers that results in
a target ratio of 0:1 between their objects and IO-backed caches.  This
allows such virtual caches to grow when memory is available (they do
cache/avoid CPU work after all), but effectively disables them as soon as
IO-backed objects are under pressure.

It then switches the shrinkers for procfs and sysfs metadata, as well as
excess page cache shadow nodes, to the new zero-seek setting.

Link: http://lkml.kernel.org/r/20181009184732.762-5-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Domas Mituzas <dmituzas@fb.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Rik van Riel <riel@surriel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-10-26 16:26:33 -07:00
Alexey Dobriyan 2d6e4e822a proc: fixup PDE allocation bloat
24074a35c5 ("proc: Make inline name size calculation automatic")
started to put PDE allocations into kmalloc-256 which is unnecessary as
~40 character names are very rare.

Put allocation back into kmalloc-192 cache for 64-bit non-debug builds.

Put BUILD_BUG_ON to know when PDE size has gotten out of control.

[adobriyan@gmail.com: fix BUILD_BUG_ON breakage on powerpc64]
  Link: http://lkml.kernel.org/r/20180703191602.GA25521@avx2
Link: http://lkml.kernel.org/r/20180617215732.GA24688@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-08-22 10:52:45 -07:00
David Howells 24074a35c5 proc: Make inline name size calculation automatic
Make calculation of the size of the inline name in struct proc_dir_entry
automatic, rather than having to manually encode the numbers and failing to
allow for lockdep.

Require a minimum inline name size of 33+1 to allow for names that look
like two hex numbers with a dash between.

Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2018-06-15 00:48:57 -04:00
Alexey Dobriyan b4884f2333 proc: move "struct proc_dir_entry" into kmem cache
"struct proc_dir_entry" is variable sized because of 0-length trailing
array for name, however, because of SLAB padding allocations it is
possible to make "struct proc_dir_entry" fixed sized and allocate same
amount of memory.

It buys fine-grained debugging with poisoning and usercopy protection
which is not possible with kmalloc-* caches.

Currently, on 32-bit 91+ byte allocations go into kmalloc-128 and on
64-bit 147+ byte allocations go to kmalloc-192 anyway.

Additional memory is allocated only for 38/46+ byte long names which are
rare or may not even exist in the wild.

Link: http://lkml.kernel.org/r/20180223205504.GA17139@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-04-11 10:28:34 -07:00
Alexey Dobriyan 2acddbe816 proc: account "struct pde_opener"
The allocation is persistent in fact as any fool can open a file in
/proc and sit on it.

Link: http://lkml.kernel.org/r/20180214082409.GC17157@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-04-11 10:28:33 -07:00
Alexey Dobriyan 195b8cf068 proc: move "struct pde_opener" to kmem cache
"struct pde_opener" is fixed size and we can have more granular approach
to debugging.

For those who don't know, per cache SLUB poisoning and red zoning don't
work if there is at least one object allocated which is hopeless in case
of kmalloc-64 but not in case of standalone cache.  Although systemd
opens 2 files from the get go, so it is hopeless after all.

Link: http://lkml.kernel.org/r/20180214082306.GB17157@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-04-11 10:28:33 -07:00
Alexey Dobriyan e7a6e291e3 proc: faster open/close of files without ->release hook
The whole point of code in fs/proc/inode.c is to make sure ->release
hook is called either at close() or at rmmod time.

All if it is unnecessary if there is no ->release hook.

Save allocation+list manipulations under spinlock in that case.

Link: http://lkml.kernel.org/r/20180214063033.GA15579@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-04-11 10:28:33 -07:00
Alexey Dobriyan 2f89742435 proc: do less stuff under ->pde_unload_lock
Commit ca469f35a8 ("deal with races between remove_proc_entry() and
proc_reg_release()") moved too much stuff under ->pde_unload_lock making
a problem described at series "[PATCH v5] procfs: Improve Scaling in
proc" worse.

While RCU is being figured out, move kfree() out of ->pde_unload_lock.

On my potato, difference is only 0.5% speedup with concurrent
open+read+close of /proc/cmdline, but the effect should be more
noticeable on more capable machines.

$ perf stat -r 16 -- ./proc-j 16

 Performance counter stats for './proc-j 16' (16 runs):

     130569.502377      task-clock (msec)         #   15.872 CPUs utilized            ( +-  0.05% )
            19,169      context-switches          #    0.147 K/sec                    ( +-  0.18% )
                15      cpu-migrations            #    0.000 K/sec                    ( +-  3.27% )
               437      page-faults               #    0.003 K/sec                    ( +-  1.25% )
   300,172,097,675      cycles                    #    2.299 GHz                      ( +-  0.05% )
    96,793,267,308      instructions              #    0.32  insn per cycle           ( +-  0.04% )
    22,798,342,298      branches                  #  174.607 M/sec                    ( +-  0.04% )
       111,764,687      branch-misses             #    0.49% of all branches          ( +-  0.47% )

       8.226574400 seconds time elapsed                                          ( +-  0.05% )
       ^^^^^^^^^^^

$ perf stat -r 16 -- ./proc-j 16

 Performance counter stats for './proc-j 16' (16 runs):

     129866.777392      task-clock (msec)         #   15.869 CPUs utilized            ( +-  0.04% )
            19,154      context-switches          #    0.147 K/sec                    ( +-  0.66% )
                14      cpu-migrations            #    0.000 K/sec                    ( +-  1.73% )
               431      page-faults               #    0.003 K/sec                    ( +-  1.09% )
   298,556,520,546      cycles                    #    2.299 GHz                      ( +-  0.04% )
    96,525,366,833      instructions              #    0.32  insn per cycle           ( +-  0.04% )
    22,730,194,043      branches                  #  175.027 M/sec                    ( +-  0.04% )
       111,506,074      branch-misses             #    0.49% of all branches          ( +-  0.18% )

       8.183629778 seconds time elapsed                                          ( +-  0.04% )
       ^^^^^^^^^^^

Link: http://lkml.kernel.org/r/20180213132911.GA24298@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-04-11 10:28:33 -07:00
Alexey Dobriyan 15b158b4e6 proc: spread likely/unlikely a bit
use_pde() is used at every open/read/write/...  of every random /proc
file.  Negative refcount happens only if PDE is being deleted by module
(read: never).  So it gets "likely".

unuse_pde() gets "unlikely" for the same reason.

close_pdeo() gets unlikely as the completion is filled only if there is a
race between PDE removal and close() (read: never ever).

It even saves code on x86_64 defconfig:

	add/remove: 0/0 grow/shrink: 1/2 up/down: 2/-20 (-18)
	Function                                     old     new   delta
	close_pdeo                                   183     185      +2
	proc_reg_get_unmapped_area                   119     111      -8
	proc_reg_poll                                 85      73     -12

Link: http://lkml.kernel.org/r/20180104175657.GA5204@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-02-06 18:32:43 -08:00
Alexey Dobriyan efb1a57d90 fs/proc: use __ro_after_init
/proc/self inode numbers, value of proc_inode_cache and st_nlink of
/proc/$TGID are fixed constants.

Link: http://lkml.kernel.org/r/20180103184707.GA31849@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-02-06 18:32:43 -08:00
Linus Torvalds 168fe32a07 Merge branch 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull poll annotations from Al Viro:
 "This introduces a __bitwise type for POLL### bitmap, and propagates
  the annotations through the tree. Most of that stuff is as simple as
  'make ->poll() instances return __poll_t and do the same to local
  variables used to hold the future return value'.

  Some of the obvious brainos found in process are fixed (e.g. POLLIN
  misspelled as POLL_IN). At that point the amount of sparse warnings is
  low and most of them are for genuine bugs - e.g. ->poll() instance
  deciding to return -EINVAL instead of a bitmap. I hadn't touched those
  in this series - it's large enough as it is.

  Another problem it has caught was eventpoll() ABI mess; select.c and
  eventpoll.c assumed that corresponding POLL### and EPOLL### were
  equal. That's true for some, but not all of them - EPOLL### are
  arch-independent, but POLL### are not.

  The last commit in this series separates userland POLL### values from
  the (now arch-independent) kernel-side ones, converting between them
  in the few places where they are copied to/from userland. AFAICS, this
  is the least disruptive fix preserving poll(2) ABI and making epoll()
  work on all architectures.

  As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
  it will trigger only on what would've triggered EPOLLWRBAND on other
  architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
  at all on sparc. With this patch they should work consistently on all
  architectures"

* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
  make kernel-side POLL... arch-independent
  eventpoll: no need to mask the result of epi_item_poll() again
  eventpoll: constify struct epoll_event pointers
  debugging printk in sg_poll() uses %x to print POLL... bitmap
  annotate poll(2) guts
  9p: untangle ->poll() mess
  ->si_band gets POLL... bitmap stored into a user-visible long field
  ring_buffer_poll_wait() return value used as return value of ->poll()
  the rest of drivers/*: annotate ->poll() instances
  media: annotate ->poll() instances
  fs: annotate ->poll() instances
  ipc, kernel, mm: annotate ->poll() instances
  net: annotate ->poll() instances
  apparmor: annotate ->poll() instances
  tomoyo: annotate ->poll() instances
  sound: annotate ->poll() instances
  acpi: annotate ->poll() instances
  crypto: annotate ->poll() instances
  block: annotate ->poll() instances
  x86: annotate ->poll() instances
  ...
2018-01-30 17:58:07 -08:00
Al Viro 076ccb76e1 fs: annotate ->poll() instances
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2017-11-27 16:20:05 -05:00
Al Viro e6c8adca20 anntotate the places where ->poll() return values go
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2017-11-27 16:19:53 -05:00
Al Viro a3f8683bf7 ->poll() methods should return __poll_t
The most common place to find POLL... bitmaps: return values
of ->poll() and its subsystem counterparts.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2017-11-27 16:19:52 -05:00
Linus Torvalds 1751e8a6cb Rename superblock flags (MS_xyz -> SB_xyz)
This is a pure automated search-and-replace of the internal kernel
superblock flags.

The s_flags are now called SB_*, with the names and the values for the
moment mirroring the MS_* flags that they're equivalent to.

Note how the MS_xyz flags are the ones passed to the mount system call,
while the SB_xyz flags are what we then use in sb->s_flags.

The script to do this was:

    # places to look in; re security/*: it generally should *not* be
    # touched (that stuff parses mount(2) arguments directly), but
    # there are two places where we really deal with superblock flags.
    FILES="drivers/mtd drivers/staging/lustre fs ipc mm \
            include/linux/fs.h include/uapi/linux/bfs_fs.h \
            security/apparmor/apparmorfs.c security/apparmor/include/lib.h"
    # the list of MS_... constants
    SYMS="RDONLY NOSUID NODEV NOEXEC SYNCHRONOUS REMOUNT MANDLOCK \
          DIRSYNC NOATIME NODIRATIME BIND MOVE REC VERBOSE SILENT \
          POSIXACL UNBINDABLE PRIVATE SLAVE SHARED RELATIME KERNMOUNT \
          I_VERSION STRICTATIME LAZYTIME SUBMOUNT NOREMOTELOCK NOSEC BORN \
          ACTIVE NOUSER"

    SED_PROG=
    for i in $SYMS; do SED_PROG="$SED_PROG -e s/MS_$i/SB_$i/g"; done

    # we want files that contain at least one of MS_...,
    # with fs/namespace.c and fs/pnode.c excluded.
    L=$(for i in $SYMS; do git grep -w -l MS_$i $FILES; done| sort|uniq|grep -v '^fs/namespace.c'|grep -v '^fs/pnode.c')

    for f in $L; do sed -i $f $SED_PROG; done

Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-11-27 13:05:09 -08:00
Greg Kroah-Hartman b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00
Tobin C. Harding f245e1c17a fs/proc/inode.c: remove cast from memory allocation
Coccinelle emits this warning:

  WARNING: casting value returned by memory allocation function to (struct proc_inode *) is useless.

Remove unnecessary cast.

Link: http://lkml.kernel.org/r/1487745720-16967-1-git-send-email-me@tobin.cc
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-05-08 17:15:10 -07:00
Lafcadio Wluiki 796f571b0c procfs: use an enum for possible hidepid values
Previously, the hidepid parameter was checked by comparing literal
integers 0, 1, 2.  Let's add a proper enum for this, to make the
checking more expressive:

        0 → HIDEPID_OFF
        1 → HIDEPID_NO_ACCESS
        2 → HIDEPID_INVISIBLE

This changes the internal labelling only, the userspace-facing interface
remains unmodified, and still works with literal integers 0, 1, 2.

No functional changes.

Link: http://lkml.kernel.org/r/1484572984-13388-2-git-send-email-djalal@gmail.com
Signed-off-by: Lafcadio Wluiki <wluikil@gmail.com>
Signed-off-by: Djalal Harouni <tixxdz@gmail.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-02-24 17:46:56 -08:00
Konstantin Khlebnikov d6cffbbe9a proc/sysctl: prune stale dentries during unregistering
Currently unregistering sysctl table does not prune its dentries.
Stale dentries could slowdown sysctl operations significantly.

For example, command:

 # for i in {1..100000} ; do unshare -n -- sysctl -a &> /dev/null ; done
 creates a millions of stale denties around sysctls of loopback interface:

 # sysctl fs.dentry-state
 fs.dentry-state = 25812579  24724135        45      0       0       0

 All of them have matching names thus lookup have to scan though whole
 hash chain and call d_compare (proc_sys_compare) which checks them
 under system-wide spinlock (sysctl_lock).

 # time sysctl -a > /dev/null
 real    1m12.806s
 user    0m0.016s
 sys     1m12.400s

Currently only memory reclaimer could remove this garbage.
But without significant memory pressure this never happens.

This patch collects sysctl inodes into list on sysctl table header and
prunes all their dentries once that table unregisters.

Konstantin Khlebnikov <khlebnikov@yandex-team.ru> writes:
> On 10.02.2017 10:47, Al Viro wrote:
>> how about >> the matching stats *after* that patch?
>
> dcache size doesn't grow endlessly, so stats are fine
>
> # sysctl fs.dentry-state
> fs.dentry-state = 92712	58376	45	0	0	0
>
> # time sysctl -a &>/dev/null
>
> real	0m0.013s
> user	0m0.004s
> sys	0m0.008s

Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
2017-02-13 17:00:06 +13:00
Linus Torvalds 7c0f6ba682 Replace <asm/uaccess.h> with <linux/uaccess.h> globally
This was entirely automated, using the script by Al:

  PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
  sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
        $(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)

to do the replacement at the end of the merge window.

Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-12-24 11:46:01 -08:00
Linus Torvalds 231753ef78 Merge uncontroversial parts of branch 'readlink' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull partial readlink cleanups from Miklos Szeredi.

This is the uncontroversial part of the readlink cleanup patch-set that
simplifies the default readlink handling.

Miklos and Al are still discussing the rest of the series.

* git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
  vfs: make generic_readlink() static
  vfs: remove ".readlink = generic_readlink" assignments
  vfs: default to generic_readlink()
  vfs: replace calling i_op->readlink with vfs_readlink()
  proc/self: use generic_readlink
  ecryptfs: use vfs_get_link()
  bad_inode: add missing i_op initializers
2016-12-17 19:16:12 -08:00
Alexey Dobriyan 492b2da605 proc: tweak comments about 2 stage open and everything
Some comments were obsoleted since commit 05c0ae21c0 ("try a saner
locking for pde_opener...").

Some new comments added.

Some confusing comments replaced with equally confusing ones.

Link: http://lkml.kernel.org/r/20161029160231.GD1246@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-12-12 18:55:09 -08:00
Alexey Dobriyan 39a10ac23c proc: kmalloc struct pde_opener
kzalloc is too much, half of the fields will be reinitialized anyway.

If proc file doesn't have ->release hook (some still do not), clearing
is unnecessary because it will be freed immediately.

Link: http://lkml.kernel.org/r/20161029155747.GC1246@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-12-12 18:55:09 -08:00
Alexey Dobriyan f5887c71cf proc: fix type of struct pde_opener::closing field
struct pde_opener::closing is boolean.

Link: http://lkml.kernel.org/r/20161029155439.GB1246@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-12-12 18:55:09 -08:00
Alexey Dobriyan 06a0c4175d proc: just list_del() struct pde_opener
list_del_init() is too much, structure will be freed in three lines
anyway.

Link: http://lkml.kernel.org/r/20161029155313.GA1246@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-12-12 18:55:09 -08:00
Miklos Szeredi dfeef68862 vfs: remove ".readlink = generic_readlink" assignments
If .readlink == NULL implies generic_readlink().

Generated by:

to_del="\.readlink.*=.*generic_readlink"
for i in `git grep -l $to_del`; do sed -i "/$to_del"/d $i; done

Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
2016-12-09 16:45:04 +01:00
Deepa Dinamani 078cd8279e fs: Replace CURRENT_TIME with current_time() for inode timestamps
CURRENT_TIME macro is not appropriate for filesystems as it
doesn't use the right granularity for filesystem timestamps.
Use current_time() instead.

CURRENT_TIME is also not y2038 safe.

This is also in preparation for the patch that transitions
vfs timestamps to use 64 bit time and hence make them
y2038 safe. As part of the effort current_time() will be
extended to do range checks. Hence, it is necessary for all
file system timestamps to use current_time(). Also,
current_time() will be transitioned along with vfs to be
y2038 safe.

Note that whenever a single call to current_time() is used
to change timestamps in different inodes, it is because they
share the same time granularity.

Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felipe Balbi <balbi@kernel.org>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
Acked-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Acked-by: David Sterba <dsterba@suse.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2016-09-27 21:06:21 -04:00
Deepa Dinamani 2554c72edb fs: proc: Delete inode time initializations in proc_alloc_inode()
proc uses new_inode_pseudo() to allocate a new inode.
This in turn calls the proc_inode_alloc() callback.
But, at this point, inode is still not initialized
with the super_block pointer which only happens just
before alloc_inode() returns after the call to
inode_init_always().

Also, the inode times are initialized again after the
call to new_inode_pseudo() in proc_inode_alloc().
The assignemet in proc_alloc_inode() is redundant and
also doesn't work after the current_time() api is
changed to take struct inode* instead of
struct *super_block.

This bug was reported after current_time() was used to
assign times in proc_alloc_inode().

Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com> [0-day test robot]
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2016-09-27 21:06:20 -04:00
Linus Torvalds a867d7349e Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull userns vfs updates from Eric Biederman:
 "This tree contains some very long awaited work on generalizing the
  user namespace support for mounting filesystems to include filesystems
  with a backing store.  The real world target is fuse but the goal is
  to update the vfs to allow any filesystem to be supported.  This
  patchset is based on a lot of code review and testing to approach that
  goal.

  While looking at what is needed to support the fuse filesystem it
  became clear that there were things like xattrs for security modules
  that needed special treatment.  That the resolution of those concerns
  would not be fuse specific.  That sorting out these general issues
  made most sense at the generic level, where the right people could be
  drawn into the conversation, and the issues could be solved for
  everyone.

  At a high level what this patchset does a couple of simple things:

   - Add a user namespace owner (s_user_ns) to struct super_block.

   - Teach the vfs to handle filesystem uids and gids not mapping into
     to kuids and kgids and being reported as INVALID_UID and
     INVALID_GID in vfs data structures.

  By assigning a user namespace owner filesystems that are mounted with
  only user namespace privilege can be detected.  This allows security
  modules and the like to know which mounts may not be trusted.  This
  also allows the set of uids and gids that are communicated to the
  filesystem to be capped at the set of kuids and kgids that are in the
  owning user namespace of the filesystem.

  One of the crazier corner casees this handles is the case of inodes
  whose i_uid or i_gid are not mapped into the vfs.  Most of the code
  simply doesn't care but it is easy to confuse the inode writeback path
  so no operation that could cause an inode write-back is permitted for
  such inodes (aka only reads are allowed).

  This set of changes starts out by cleaning up the code paths involved
  in user namespace permirted mounts.  Then when things are clean enough
  adds code that cleanly sets s_user_ns.  Then additional restrictions
  are added that are possible now that the filesystem superblock
  contains owner information.

  These changes should not affect anyone in practice, but there are some
  parts of these restrictions that are changes in behavior.

   - Andy's restriction on suid executables that does not honor the
     suid bit when the path is from another mount namespace (think
     /proc/[pid]/fd/) or when the filesystem was mounted by a less
     privileged user.

   - The replacement of the user namespace implicit setting of MNT_NODEV
     with implicitly setting SB_I_NODEV on the filesystem superblock
     instead.

     Using SB_I_NODEV is a stronger form that happens to make this state
     user invisible.  The user visibility can be managed but it caused
     problems when it was introduced from applications reasonably
     expecting mount flags to be what they were set to.

  There is a little bit of work remaining before it is safe to support
  mounting filesystems with backing store in user namespaces, beyond
  what is in this set of changes.

   - Verifying the mounter has permission to read/write the block device
     during mount.

   - Teaching the integrity modules IMA and EVM to handle filesystems
     mounted with only user namespace root and to reduce trust in their
     security xattrs accordingly.

   - Capturing the mounters credentials and using that for permission
     checks in d_automount and the like.  (Given that overlayfs already
     does this, and we need the work in d_automount it make sense to
     generalize this case).

  Furthermore there are a few changes that are on the wishlist:

   - Get all filesystems supporting posix acls using the generic posix
     acls so that posix_acl_fix_xattr_from_user and
     posix_acl_fix_xattr_to_user may be removed.  [Maintainability]

   - Reducing the permission checks in places such as remount to allow
     the superblock owner to perform them.

   - Allowing the superblock owner to chown files with unmapped uids and
     gids to something that is mapped so the files may be treated
     normally.

  I am not considering even obvious relaxations of permission checks
  until it is clear there are no more corner cases that need to be
  locked down and handled generically.

  Many thanks to Seth Forshee who kept this code alive, and putting up
  with me rewriting substantial portions of what he did to handle more
  corner cases, and for his diligent testing and reviewing of my
  changes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (30 commits)
  fs: Call d_automount with the filesystems creds
  fs: Update i_[ug]id_(read|write) to translate relative to s_user_ns
  evm: Translate user/group ids relative to s_user_ns when computing HMAC
  dquot: For now explicitly don't support filesystems outside of init_user_ns
  quota: Handle quota data stored in s_user_ns in quota_setxquota
  quota: Ensure qids map to the filesystem
  vfs: Don't create inodes with a uid or gid unknown to the vfs
  vfs: Don't modify inodes with a uid or gid unknown to the vfs
  cred: Reject inodes with invalid ids in set_create_file_as()
  fs: Check for invalid i_uid in may_follow_link()
  vfs: Verify acls are valid within superblock's s_user_ns.
  userns: Handle -1 in k[ug]id_has_mapping when !CONFIG_USER_NS
  fs: Refuse uid/gid changes which don't map into s_user_ns
  selinux: Add support for unprivileged mounts from user namespaces
  Smack: Handle labels consistently in untrusted mounts
  Smack: Add support for unprivileged mounts from user namespaces
  fs: Treat foreign mounts as nosuid
  fs: Limit file caps to the user namespace of the super block
  userns: Remove the now unnecessary FS_USERNS_DEV_MOUNT flag
  userns: Remove implicit MNT_NODEV fragility.
  ...
2016-07-29 15:54:19 -07:00
Eric W. Biederman a2982cc922 vfs: Generalize filesystem nodev handling.
Introduce a function may_open_dev that tests MNT_NODEV and a new
superblock flab SB_I_NODEV.  Use this new function in all of the
places where MNT_NODEV was previously tested.

Add the new SB_I_NODEV s_iflag to proc, sysfs, and mqueuefs as those
filesystems should never support device nodes, and a simple superblock
flags makes that very hard to get wrong.  With SB_I_NODEV set if any
device nodes somehow manage to show up on on a filesystem those
device nodes will be unopenable.

Acked-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
2016-06-23 15:41:57 -05:00
Eric W. Biederman e94591d0d9 proc: Convert proc_mount to use mount_ns.
Move the call of get_pid_ns, the call of proc_parse_options, and
the setting of s_iflags into proc_fill_super so that mount_ns
can be used.

Convert proc_mount to call mount_ns and remove the now unnecessary
code.

Acked-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Djalal Harouni <tixxdz@gmail.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
2016-06-23 15:41:54 -05:00
Eric W. Biederman 8654df4e2a mnt: Refactor fs_fully_visible into mount_too_revealing
Replace the call of fs_fully_visible in do_new_mount from before the
new superblock is allocated with a call of mount_too_revealing after
the superblock is allocated.   This winds up being a much better location
for maintainability of the code.

The first change this enables is the replacement of FS_USERNS_VISIBLE
with SB_I_USERNS_VISIBLE.  Moving the flag from struct filesystem_type
to sb_iflags on the superblock.

Unfortunately mount_too_revealing fundamentally needs to touch
mnt_flags adding several MNT_LOCKED_XXX flags at the appropriate
times.  If the mnt_flags did not need to be touched the code
could be easily moved into the filesystem specific mount code.

Acked-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
2016-06-23 15:41:46 -05:00
Vladimir Davydov 5d097056c9 kmemcg: account certain kmem allocations to memcg
Mark those kmem allocations that are known to be easily triggered from
userspace as __GFP_ACCOUNT/SLAB_ACCOUNT, which makes them accounted to
memcg.  For the list, see below:

 - threadinfo
 - task_struct
 - task_delay_info
 - pid
 - cred
 - mm_struct
 - vm_area_struct and vm_region (nommu)
 - anon_vma and anon_vma_chain
 - signal_struct
 - sighand_struct
 - fs_struct
 - files_struct
 - fdtable and fdtable->full_fds_bits
 - dentry and external_name
 - inode for all filesystems. This is the most tedious part, because
   most filesystems overwrite the alloc_inode method.

The list is far from complete, so feel free to add more objects.
Nevertheless, it should be close to "account everything" approach and
keep most workloads within bounds.  Malevolent users will be able to
breach the limit, but this was possible even with the former "account
everything" approach (simply because it did not account everything in
fact).

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Greg Thelen <gthelen@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-01-14 16:00:49 -08:00
Al Viro fceef393a5 switch ->get_link() to delayed_call, kill ->put_link()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2015-12-30 13:01:03 -05:00
Al Viro 6b2553918d replace ->follow_link() with new method that could stay in RCU mode
new method: ->get_link(); replacement of ->follow_link().  The differences
are:
	* inode and dentry are passed separately
	* might be called both in RCU and non-RCU mode;
the former is indicated by passing it a NULL dentry.
	* when called that way it isn't allowed to block
and should return ERR_PTR(-ECHILD) if it needs to be called
in non-RCU mode.

It's a flagday change - the old method is gone, all in-tree instances
converted.  Conversion isn't hard; said that, so far very few instances
do not immediately bail out when called in RCU mode.  That'll change
in the next commits.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2015-12-08 22:41:54 -05:00
Linus Torvalds 0cbee99269 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull user namespace updates from Eric Biederman:
 "Long ago and far away when user namespaces where young it was realized
  that allowing fresh mounts of proc and sysfs with only user namespace
  permissions could violate the basic rule that only root gets to decide
  if proc or sysfs should be mounted at all.

  Some hacks were put in place to reduce the worst of the damage could
  be done, and the common sense rule was adopted that fresh mounts of
  proc and sysfs should allow no more than bind mounts of proc and
  sysfs.  Unfortunately that rule has not been fully enforced.

  There are two kinds of gaps in that enforcement.  Only filesystems
  mounted on empty directories of proc and sysfs should be ignored but
  the test for empty directories was insufficient.  So in my tree
  directories on proc, sysctl and sysfs that will always be empty are
  created specially.  Every other technique is imperfect as an ordinary
  directory can have entries added even after a readdir returns and
  shows that the directory is empty.  Special creation of directories
  for mount points makes the code in the kernel a smidge clearer about
  it's purpose.  I asked container developers from the various container
  projects to help test this and no holes were found in the set of mount
  points on proc and sysfs that are created specially.

  This set of changes also starts enforcing the mount flags of fresh
  mounts of proc and sysfs are consistent with the existing mount of
  proc and sysfs.  I expected this to be the boring part of the work but
  unfortunately unprivileged userspace winds up mounting fresh copies of
  proc and sysfs with noexec and nosuid clear when root set those flags
  on the previous mount of proc and sysfs.  So for now only the atime,
  read-only and nodev attributes which userspace happens to keep
  consistent are enforced.  Dealing with the noexec and nosuid
  attributes remains for another time.

  This set of changes also addresses an issue with how open file
  descriptors from /proc/<pid>/ns/* are displayed.  Recently readlink of
  /proc/<pid>/fd has been triggering a WARN_ON that has not been
  meaningful since it was added (as all of the code in the kernel was
  converted) and is not now actively wrong.

  There is also a short list of issues that have not been fixed yet that
  I will mention briefly.

  It is possible to rename a directory from below to above a bind mount.
  At which point any directory pointers below the renamed directory can
  be walked up to the root directory of the filesystem.  With user
  namespaces enabled a bind mount of the bind mount can be created
  allowing the user to pick a directory whose children they can rename
  to outside of the bind mount.  This is challenging to fix and doubly
  so because all obvious solutions must touch code that is in the
  performance part of pathname resolution.

  As mentioned above there is also a question of how to ensure that
  developers by accident or with purpose do not introduce exectuable
  files on sysfs and proc and in doing so introduce security regressions
  in the current userspace that will not be immediately obvious and as
  such are likely to require breaking userspace in painful ways once
  they are recognized"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
  vfs: Remove incorrect debugging WARN in prepend_path
  mnt: Update fs_fully_visible to test for permanently empty directories
  sysfs: Create mountpoints with sysfs_create_mount_point
  sysfs: Add support for permanently empty directories to serve as mount points.
  kernfs: Add support for always empty directories.
  proc: Allow creating permanently empty directories that serve as mount points
  sysctl: Allow creating permanently empty directories that serve as mountpoints.
  fs: Add helper functions for permanently empty directories.
  vfs: Ignore unlocked mounts in fs_fully_visible
  mnt: Modify fs_fully_visible to deal with locked ro nodev and atime
  mnt: Refactor the logic for mounting sysfs and proc in a user namespace
2015-07-03 15:20:57 -07:00
Eric W. Biederman eb6d38d542 proc: Allow creating permanently empty directories that serve as mount points
Add a new function proc_create_mount_point that when used to creates a
directory that can not be added to.

Add a new function is_empty_pde to test if a function is a mount
point.

Update the code to use make_empty_dir_inode when reporting
a permanently empty directory to the vfs.

Update the code to not allow adding to permanently empty directories.

Update /proc/openprom and /proc/fs/nfsd to be permanently empty directories.

Cc: stable@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
2015-07-01 10:36:41 -05:00
Al Viro 5f2c4179e1 switch ->put_link() from dentry to inode
only one instance looks at that argument at all; that sole
exception wants inode rather than dentry.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2015-05-11 08:13:12 -04:00
Al Viro 6e77137b36 don't pass nameidata to ->follow_link()
its only use is getting passed to nd_jump_link(), which can obtain
it from current->nameidata

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2015-05-10 22:20:15 -04:00
Al Viro 680baacbca new ->follow_link() and ->put_link() calling conventions
a) instead of storing the symlink body (via nd_set_link()) and returning
an opaque pointer later passed to ->put_link(), ->follow_link() _stores_
that opaque pointer (into void * passed by address by caller) and returns
the symlink body.  Returning ERR_PTR() on error, NULL on jump (procfs magic
symlinks) and pointer to symlink body for normal symlinks.  Stored pointer
is ignored in all cases except the last one.

Storing NULL for opaque pointer (or not storing it at all) means no call
of ->put_link().

b) the body used to be passed to ->put_link() implicitly (via nameidata).
Now only the opaque pointer is.  In the cases when we used the symlink body
to free stuff, ->follow_link() now should store it as opaque pointer in addition
to returning it.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2015-05-10 22:19:45 -04:00
David Howells 2b0143b5c9 VFS: normal filesystems (and lustre): d_inode() annotations
that's the bulk of filesystem drivers dealing with inodes of their own

Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2015-04-15 15:06:57 -04:00
Al Viro 7e0e953bb0 procfs: fix race between symlink removals and traversals
use_pde()/unuse_pde() in ->follow_link()/->put_link() resp.

Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2015-02-22 11:43:12 -05:00
Alexander Kuleshov 6bee55f94f fs: proc: use PDE() to get proc_dir_entry
Use the PDE() helper to get proc_dir_entry instead of coding it directly.

Signed-off-by: Alexander Kuleshov <kuleshovmail@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-02-12 18:54:12 -08:00
Al Viro 3d3d35b1e9 kill proc_ns completely
procfs inodes need only the ns_ops part; nsfs inodes don't need it at all

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2014-12-10 21:30:57 -05:00
Al Viro e149ed2b80 take the targets of /proc/*/ns/* symlinks to separate fs
New pseudo-filesystem: nsfs.  Targets of /proc/*/ns/* live there now.
It's not mountable (not even registered, so it's not in /proc/filesystems,
etc.).  Files on it *are* bindable - we explicitly permit that in do_loopback().

This stuff lives in fs/nsfs.c now; proc_ns_fget() moved there as well.
get_proc_ns() is a macro now (it's simply returning ->i_private; would
have been an inline, if not for header ordering headache).
proc_ns_inode() is an ex-parrot.  The interface used in procfs is
ns_get_path(path, task, ops) and ns_get_name(buf, size, task, ops).

Dentries and inodes are never hashed; a non-counting reference to dentry
is stashed in ns_common (removed by ->d_prune()) and reused by ns_get_path()
if present.  See ns_get_path()/ns_prune_dentry/nsfs_evict() for details
of that mechanism.

As the result, proc_ns_follow_link() has stopped poking in nd->path.mnt;
it does nd_jump_link() on a consistent <vfsmount,dentry> pair it gets
from ns_get_path().

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2014-12-10 21:30:20 -05:00
Al Viro 33c429405a copy address of proc_ns_ops into ns_common
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2014-12-04 14:34:47 -05:00
Al Viro 64964528b2 make proc_ns_operations work with struct ns_common * instead of void *
We can do that now.  And kill ->inum(), while we are at it - all instances
are identical.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2014-12-04 14:34:17 -05:00
Eric W. Biederman 0097875bd4 proc: Implement /proc/thread-self to point at the directory of the current thread
/proc/thread-self is derived from /proc/self.  /proc/thread-self
points to the directory in proc containing information about the
current thread.

This funtionality has been missing for a long time, and is tricky to
implement in userspace as gettid() is not exported by glibc.  More
importantly this allows fixing defects in /proc/mounts and /proc/net
where in a threaded application today they wind up being empty files
when only the initial pthread has exited, causing problems for other
threads.

Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
2014-08-04 10:07:11 -07:00
Monam Agarwal 1c44dbc82f fs/proc/inode.c: use RCU_INIT_POINTER(x, NULL)
Replace rcu_assign_pointer(x, NULL) with RCU_INIT_POINTER(x, NULL)

The rcu_assign_pointer() ensures that the initialization of a structure
is carried out before storing a pointer to that structure.  And in the
case of the NULL pointer, there is no structure to initialize.  So,
rcu_assign_pointer(p, NULL) can be safely converted to
RCU_INIT_POINTER(p, NULL)

Signed-off-by: Monam Agarwal <monamagarwal123@gmail.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-04-07 16:36:04 -07:00
Johannes Weiner 91b0abe36a mm + fs: store shadow entries in page cache
Reclaim will be leaving shadow entries in the page cache radix tree upon
evicting the real page.  As those pages are found from the LRU, an
iput() can lead to the inode being freed concurrently.  At this point,
reclaim must no longer install shadow pages because the inode freeing
code needs to ensure the page tree is really empty.

Add an address_space flag, AS_EXITING, that the inode freeing code sets
under the tree lock before doing the final truncate.  Reclaim will check
for this flag before installing shadow pages.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Bob Liu <bob.liu@oracle.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jan Kara <jack@suse.cz>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Luigi Semenzato <semenzato@google.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Metin Doslu <metin@citusdata.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Ozgun Erdogan <ozgun@citusdata.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Roman Gushchin <klamm@yandex-team.ru>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-04-03 16:21:01 -07:00