- Reorganize Tegra AFI/PHY/REFCLK/etc functions (Manikanta Maddireddy)
- Mask Tegra AFI_INTR in runtime suspend (Manikanta Maddireddy)
- Fix Tegra AFI/PCIe powerup sequence (Manikanta Maddireddy)
- Add Tegra124, Tegra132, Tegra210, and Tegra186 support for Gen2 link
speed (Manikanta Maddireddy)
- Advertise Tegra AER support (Manikanta Maddireddy)
- Program Tegra210 UPHY settings (Manikanta Maddireddy)
- Enable Tegra opportunistic UpdateFC and ACK (Manikanta Maddireddy)
- Disable Tegra AFI dynamic clock gating (Manikanta Maddireddy)
- Process Tegra pending DLL transactions before entering L1 or L2 to
prevent receiver errors (Manikanta Maddireddy)
- Enable Tegra xclk clock clamping in L1 (Manikanta Maddireddy)
- Increase Tegra deskew retry time (Manikanta Maddireddy)
- Work around Tegra hardware RAW erratum (Manikanta Maddireddy)
- Update Tegra210 flow control timer frequency (Manikanta Maddireddy)
- Work around Tegra Gen1/Gen2 link number negotiation issue (Manikanta
Maddireddy)
- Work around Tegra PLLE power down issue (Manikanta Maddireddy)
- Program Tegra20 to support cacheable upstream transactions (Manikanta
Maddireddy)
- Log Tegra PRSNT_SENSE_IRQ as debug, not err (Manikanta Maddireddy)
- Add register offset for third Root Port on Tegra186 and Tegra30
(Manikanta Maddireddy)
- Document Tegra PCIe DPD pinctrl property (Manikanta Maddireddy)
- Put Tegra PEX CLK & BIAS pads in DPD mode to reduce power usage when
powergated (Manikanta Maddireddy)
- Add generic DT binding for "reset-gpios" property (Manikanta
Maddireddy)
- Add Tegra support for GPIO-based PERST# (Manikanta Maddireddy)
- Enable Relaxed Ordering only for Tegra20 & Tegra30 (Vidya Sagar)
* remotes/lorenzo/pci/tegra:
PCI: tegra: Enable Relaxed Ordering only for Tegra20 & Tegra30
PCI: tegra: Change link retry log level to debug
PCI: tegra: Add support for GPIO based PERST#
PCI: Add DT binding for "reset-gpios" property
PCI: tegra: Put PEX CLK & BIAS pads in DPD mode
dt-bindings: pci: tegra: Document PCIe DPD pinctrl optional prop
PCI: tegra: Add AFI_PEX2_CTRL reg offset as part of SoC struct
PCI: tegra: Change PRSNT_SENSE IRQ log to debug
PCI: tegra: Program AFI_CACHE_BAR_{0,1}_{ST,SZ} registers only for Tegra20
PCI: tegra: Fix PLLE power down issue due to CLKREQ# signal
PCI: tegra: Set target speed as Gen1 before starting LTSSM
PCI: tegra: Update flow control timer frequency in Tegra210
PCI: tegra: Add SW fixup for RAW violations
PCI: tegra: Increase the deskew retry time
PCI: tegra: Enable PCIe xclk clock clamping
PCI: tegra: Process pending DLL transactions before entering L1 or L2
PCI: tegra: Disable AFI dynamic clock gating
PCI: tegra: Enable opportunistic UpdateFC and ACK
PCI: tegra: Program UPHY electrical settings for Tegra210
PCI: tegra: Advertise PCIe Advanced Error Reporting (AER) capability
PCI: tegra: Add PCIe Gen2 link speed support
PCI: tegra: Fix PCIe host power up sequence
PCI: tegra: Mask AFI_INTR in runtime suspend
PCI: tegra: Rearrange Tegra PCIe driver functions
PCI: tegra: Handle failure cases in tegra_pcie_power_on()
soc/tegra: pmc: Export tegra_powergate_power_on()
- Move qcom driver to bulk clock API (Bjorn Andersson)
- Add Qualcomm QCS404 PCIe controller support (Bjorn Andersson)
- Ensure Qualcomm PERST is asserted for at least 100ms (Niklas Cassel)
* remotes/lorenzo/pci/qcom:
PCI: qcom: Ensure that PERST is asserted for at least 100 ms
PCI: qcom: Add QCS404 PCIe controller support
dt-bindings: PCI: qcom: Add QCS404 to the binding
PCI: qcom: Use clk bulk API for 2.4.0 controllers
- Unify mobiveil register accessors (Hou Zhiqiang)
- Remove MSI_FLAG_MULTI_PCI_MSI since mobiveil hardware doesn't support
Multiple MSI (Hou Zhiqiang)
- Program outbound windows with base address from DT instead of assuming
zero (Hou Zhiqiang)
- Skip "safe" list traversal when it's unnecessary (Hou Zhiqiang)
- Initialize WIN_NUM_0 explicitly for CFG outbound transactions (Hou
Zhiqiang)
- Use WIN_NUM_0 for MEM inbound transactions (Hou Zhiqiang)
- Fix up mobiveil Class Code to PCI_CLASS_BRIDGE_PCI (Hou Zhiqiang)
- Wait for link-up before enumerating devices, not while initializing
host (Hou Zhiqiang)
- Move IRQ chained handler setup out of DT code (Hou Zhiqiang)
- Set primary/secondary/subordinate bus numbers (Hou Zhiqiang)
- Fix "valid device" check to allow root bus device 0 to be
multi-function (Hou Zhiqiang)
- Make DT "gpio_slave" and "apb_csr" properties optional (Hou Zhiqiang)
- Refactor MEM/IO outbound window initialization (Hou Zhiqiang)
- Fix validity check for inbound/outbound window programming (Hou
Zhiqiang)
- Initialize and preserve window control bits (Hou Zhiqiang)
- Fix 64-bit outbound window setup (both CPU and PCI addresses) (Hou
Zhiqiang)
- Move IO port setup to host init (Hou Zhiqiang)
- Fix infinite loop in INTx ISR (Hou Zhiqiang)
- Fix INTx interrupt clearing to avoid missed interrupts (Hou Zhiqiang)
* remotes/lorenzo/pci/mobiveil:
PCI: mobiveil: Fix INTx interrupt clearing in mobiveil_pcie_isr()
PCI: mobiveil: Fix infinite-loop in the INTx handling function
PCI: mobiveil: Move PCIe PIO enablement out of inbound window routine
PCI: mobiveil: Add upper 32-bit PCI base address setup in inbound window
PCI: mobiveil: Add upper 32-bit CPU base address setup in outbound window
PCI: mobiveil: Mask out hardcoded bits in inbound/outbound windows setup
PCI: mobiveil: Clear the control fields before updating it
PCI: mobiveil: Add configured inbound windows counter
PCI: mobiveil: Fix the valid check for inbound and outbound windows
PCI: mobiveil: Clean-up program_{ib/ob}_windows()
PCI: mobiveil: Remove an unnecessary return value check
PCI: mobiveil: Fix error return values
PCI: mobiveil: Refactor the MEM/IO outbound window initialization
PCI: mobiveil: Make some register updates more readable
PCI: mobiveil: Reformat the code for readability
dt-bindings: PCI: mobiveil: Change gpio_slave and apb_csr to optional
PCI: mobiveil: Fix devfn check in mobiveil_pcie_valid_device()
PCI: mobiveil: Initialize Primary/Secondary/Subordinate bus numbers
PCI: mobiveil: Move IRQ chained handler setup out of DT parse
PCI: mobiveil: Move the link up waiting out of mobiveil_host_init()
PCI: mobiveil: Fix the Class Code field
PCI: mobiveil: Use the 1st inbound window for MEM inbound transactions
PCI: mobiveil: Use WIN_NUM_0 explicitly for CFG outbound window
PCI: mobiveil: Update the resource list traversal function
PCI: mobiveil: Fix PCI base address in MEM/IO outbound windows
PCI: mobiveil: Remove the flag MSI_FLAG_MULTI_PCI_MSI
PCI: mobiveil: Unify register accessors
- Add dwc API support to de-initialize host (Vidya Sagar)
- Clean up dwc DBI,ATU read and write APIs (Vidya Sagar)
- Export dwc APIs to support .remove() so drivers can be modular (Vidya
Sagar)
- Simplify imx6 Kconfig dependencies (Leonard Crestez)
- Fix dra7xx build error when !CONFIG_GPIOLIB (YueHaibing)
* remotes/lorenzo/pci/dwc:
PCI: dwc: pci-dra7xx: Fix compilation when !CONFIG_GPIOLIB
PCI: imx6: Simplify Kconfig depends on
PCI: dwc: Export APIs to support .remove() implementation
PCI: dwc: Cleanup DBI,ATU read and write APIs
PCI: dwc: Add API support to de-initialize host
If CONFIG_GPIOLIB is not selected the compilation results in the
following build errors:
drivers/pci/controller/dwc/pci-dra7xx.c:
In function dra7xx_pcie_probe:
drivers/pci/controller/dwc/pci-dra7xx.c:777:10:
error: implicit declaration of function devm_gpiod_get_optional;
did you mean devm_regulator_get_optional? [-Werror=implicit-function-declaration]
reset = devm_gpiod_get_optional(dev, NULL, GPIOD_OUT_HIGH);
drivers/pci/controller/dwc/pci-dra7xx.c:778:45: error: ‘GPIOD_OUT_HIGH’
undeclared (first use in this function); did you mean ‘GPIOF_INIT_HIGH’?
reset = devm_gpiod_get_optional(dev, NULL, GPIOD_OUT_HIGH);
^~~~~~~~~~~~~~
GPIOF_INIT_HIGH
Fix them by including the appropriate header file.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Fix typos in drivers/pci. Comment and whitespace changes only.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
The current INTx handling function clears all interrupts after
handling the first pending; this can potentially cause missing INTx
detection. Fix the code to clear only the handled INTx IRQ.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Acked-by: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
Tested-by: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
In the loop handling INTx interrupts in mobiveil_pcie_isr(), there is
no code to update the loop control variable, which is causing an
infinite loop.
Fix the code by reading the interrupt status registers inside the
loop.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Acked-by: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
Tested-by: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
Move the PCIe PIO master enablement to function mobiveil_host_init().
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Current code erroneously sets-up the lower 32-bit PCI base address in
the inbound window, which results in inbound transactions not working in
64-bit platforms.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Current code erroneously sets-up only the lower 32-bit CPU base address
in the outbound window, which results in outbound transactions not
working in 64-bit platforms.
Fix it.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
The lower 10 bits of window size field are hardcoded to zero in HW so
they can't really be changed but the lower 10-bit of PAB_AXI_AMAP_CTRL
register are used for control fields, so while programming inbound and
outbout windows decoding we should mask out the lower 10-bit of window
size to prevent overriding the control bits.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
While programming the inbound and outbound windows in
program_{ib/ob}_windows()
we shoud clear the control fields in the registers before programming
it with a new value to prevent stale bits from older configuration.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Current code only keeps track of the number of outbound windows
configured but it does not for inbound windows. Add a counter
to keep track of initialized inbound windows.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
In program_ib/ob_windows() check the window index from the function
parameter instead of the total number of initialized windows to
determine if the specified window is valid.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
In function program_ob_windows(), remove the redundant read
operations to registers PAB_AXI_AMAP_AXI_WIN and PAB_AXI_AMAP_PEX_WIN_H,
and remove the useless definition of 'value'. Rename the parameter
'config_io_bit' to 'type' and then remove the definition of 'type'.
In function program_ib_windows(), remove the definitions of
'pio_ctrl_val' and 'amap_ctrl_dw' and reduce to only one variable
'value' to keep the temporary value read from registers.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
The memory for the host controller private structure (struct
mobiveil_pcie) is allocated together with the pci_host_bridge structure
in function devm_pci_alloc_host_bridge(), so it is unnecessary to check
the return value when get the private structure pointer.
Remove the useless check.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Some error return values in the host controller driver are
either unconventional or plain wrong. Update them all with
the expected return values.
Signed-off-by: Hou Zhiqiang <Zhinqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Move the resource type check into an if/else block and only
set-up the outbound window for MEM and IO resource. No functional
change intended.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
To make some register updates more readable use a temporary
value to hold the register value and carry out the update.
Change the register update sequence to:
- Read out the original value from the target register
- Update the value
- Program the updated value back to the register
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reformat the code to make it more readable. No functional
change intended.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Current check for devfn number in mobiveil_pci_valid_device() is
wrong in that it flags as invalid functions present in PCI device 0
in the root bus while it is perfectly valid to access all functions
in PCI device 0 in the root bus.
Update the check in mobiveil_pci_valid_device() to fix the issue.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
The reset value of Primary, Secondary and Subordinate bus numbers is
zero which is a broken setup.
Program a sensible default value for Primary/Secondary/Subordinate
bus numbers.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
The irq_set_chained_handler_and_data() call is not dependent on device
tree firmware so it should be moved out of the DT parsing function for
clarity.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[lorenzo.pieralisi@arm.com: rewritten commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
The host initializing sequence does not depend on the PCIe link being
up, so move the link up check right before the code scanning the root
bus for enumeration.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Fix up the Class Code field in PCI configuration space and set it to
PCI_CLASS_BRIDGE_PCI.
Move the Class Code fixup to function mobiveil_host_init() where
it belongs.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
The inbound and outbound windows have completely separate control
registers sets in the host controller MMIO space. Windows control
register are accessed through an MMIO base address and an offset
that depends on the window index.
Since inbound and outbound windows control registers are completely
separate there is no real need to use different window indexes in the
inbound/outbound windows initialization routines to prevent clashing.
To fix this inconsistency, change the MEM inbound window index to 0,
mirroring the outbound window set-up.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[lorenzo.pieralisi@arm.com: update commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
As the .map_bus() use the WIN_NUM_0 for CFG transactions,
it is appropriate to pass WIN_NUM_0 explicitly when initializing
the CFG outbound window rather than implicitly relying on the
ob_wins_configure counter.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Code that executes the resource list traversal does not need to
delete any node therefore using the *_safe() API version is
useless.
Replace function resource_list_for_each_entry_safe() with the
resource_list_for_each_entry() counterpart.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
The outbound memory windows PCI base addresses should be taken
from the 'ranges' property of DT node to setup MEM/IO outbound
windows decoding correctly instead of being hardcoded to zero.
Update the code to retrieve the PCI base address for each range
and use it to program the outbound windows address decoders
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
The Mobiveil internal MSI controller requires separate target addresses,
one per MSI vector; this is clearly incompatible with the Multiple MSI
feature, which requires the same target address for all vectors
requested by an endpoint (ie the Message Address field in the MSI
Capability structure), so the multi MSI feature is clearly not
supported by the host controller driver.
Remove the flag MSI_FLAG_MULTI_PCI_MSI and with it multi MSI support,
fixing the misconfiguration.
Fixes: 1e913e5833 ("PCI: mobiveil: Add MSI support")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
It is confusing to have two sets of functions to read/write
registers, some with csr_readl()/csr_writel(), while others with
read_paged_register()/write_paged_register().
In the register space the lower 3KB of 4KB PCIe configure space can be
accessed directly and higher 1KB through a simple paging mechanism.
Unify the register accessors in csr_readl() and csr_writel() by
comparing the register offset with page access boundary 3KB in the
accessor internal so that the paging mechanism is hidden behind
the csr_read()/write() common function calls.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
The imx6 driver can be used on imx6sx without enabling support for
imx6q or imx7d but the "depends on" condition doesn't allow that.
Instead of making the condition even longer just make it depend on
"ARCH_MXC || COMPILE_TEST" instead.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Fix a use-after-free in hv_eject_device_work().
Fixes: 05f151a73e ("PCI: hv: Fix a memory leak in hv_eject_device_work()")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Cc: stable@vger.kernel.org
The PCI Tegra controller conversion to a device tree configurable
driver in commit d1523b52bf ("PCI: tegra: Move PCIe driver
to drivers/pci/host") implied that code for the driver can be
compiled in for a kernel supporting multiple platforms.
Unfortunately, a blind move of the code did not check that some of the
quirks that were applied in arch/arm (eg enabling Relaxed Ordering on
all PCI devices - since the quirk hook erroneously matches PCI_ANY_ID
for both Vendor-ID and Device-ID) are now applied in all kernels that
compile the PCI Tegra controlled driver, DT and ACPI alike.
This is completely wrong, in that enablement of Relaxed Ordering is only
required by default in Tegra20 platforms as described in the Tegra20
Technical Reference Manual (available at
https://developer.nvidia.com/embedded/downloads#?search=tegra%202 in
Section 34.1, where it is mentioned that Relaxed Ordering bit needs to
be enabled in its root ports to avoid deadlock in hardware) and in the
Tegra30 platforms for the same reasons (unfortunately not documented
in the TRM).
There is no other strict requirement on PCI devices Relaxed Ordering
enablement on any other Tegra platforms or PCI host bridge driver.
Fix this quite upsetting situation by limiting the vendor and device IDs
to which the Relaxed Ordering quirk applies to the root ports in
question, reported above.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
[lorenzo.pieralisi@arm.com: completely rewrote the commit log/fixes tag]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Driver checks for link up three times before giving up, each retry
attempt is printed as an error. Letting users know that PCIe link is
down and in the process of being brought up again is for debug, not an
error condition.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tegra PCIe has fixed per port SFIO line to signal PERST#, which can be
controlled by AFI port register. However, if a platform routes a
different GPIO to the PCIe slot, then port register cannot control it.
Add support for GPIO based PERST# signal for such platforms. GPIO number
comes from per port PCIe device tree node. PCIe driver probe doesn't
fail if per port "reset-gpios" property is not populated, so platforms
that require this workaround must make sure that the DT property is not
missed in the corresponding device tree.
Link: https://lore.kernel.org/linux-pci/20190705084850.30777-1-jonathanh@nvidia.com/
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
[lorenzo.pieralisi@arm.com: squashed in fix in Link]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Export all configuration space access APIs and also other APIs to
support host controller drivers of dwc core based implementations while
adding support for .remove() hook to build their respective drivers as
modules.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cleanup DBI read and write APIs by removing leading "__" (underscore)
from their names as there is no reason to have leading underscores
in the first place in the function definition.
Remove dbi/dbi2 base address parameters as the same behaviour can be
obtained through read and write APIs. Since dw_pcie_{readl/writel}_dbi()
APIs can't be used for ATU read/write as ATU base address could be
different from DBI base address, implement ATU read/write APIs using ATU
base address without using dw_pcie_{readl/writel}_dbi() APIs.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Add an API to group all the tasks to be done to de-initialize host which
can then be called by any dwc core based driver implementations
while adding .remove() support in their respective drivers.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
According to the PCI Local Bus specification Revision 3.0,
section 6.8.1.3 (Message Control for MSI), endpoints that
are Multiple Message Capable as defined by bits [3:1] in
the Message Control for MSI can request a number of vectors
that is power of two aligned.
As specified in section 6.8.1.6 "Message data for MSI", the Multiple
Message Enable field (bits [6:4] of the Message Control register)
defines the number of low order message data bits the function is
permitted to modify to generate its system software allocated
vectors.
The MSI controller in the Xilinx NWL PCIe controller supports a number
of MSI vectors specified through a bitmap and the hwirq number for an
MSI, that is the value written in the MSI data TLP is determined by
the bitmap allocation.
For instance, in a situation where two endpoints sitting on
the PCI bus request the following MSI configuration, with
the current PCI Xilinx bitmap allocation code (that does not
align MSI vector allocation on a power of two boundary):
Endpoint #1: Requesting 1 MSI vector - allocated bitmap bits 0
Endpoint #2: Requesting 2 MSI vectors - allocated bitmap bits [1,2]
The bitmap value(s) corresponds to the hwirq number that is programmed
into the Message Data for MSI field in the endpoint MSI capability
and is detected by the root complex to fire the corresponding
MSI irqs. The value written in Message Data for MSI field corresponds
to the first bit allocated in the bitmap for Multi MSI vectors.
The current Xilinx NWL MSI allocation code allows a bitmap allocation
that is not a power of two boundaries, so endpoint #2, is allowed to
toggle Message Data bit[0] to differentiate between its two vectors
(meaning that the MSI data will be respectively 0x0 and 0x1 for the two
vectors allocated to endpoint #2).
This clearly aliases with the Endpoint #1 vector allocation, resulting
in a broken Multi MSI implementation.
Update the code to allocate MSI bitmap ranges with a power of two
alignment, fixing the bug.
Fixes: ab597d35ef ("PCI: xilinx-nwl: Add support for Xilinx NWL PCIe Host Controller")
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
In Tegra210 AFI design has clamp value for the BIAS pad as 0, which keeps
the bias pad in non power down mode. This is leading to power consumption
of 2 mW in BIAS pad, even if the PCIe partition is powergated. To avoid
unnecessary power consumption, put PEX CLK & BIAS pads in deep power down
mode when PCIe partition is power gated.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tegra186 and Tegra30 have three PCIe root ports. AFI_PEX2_CTRL register
is defined for third root port. Offset of this register in Tegra186 is
different from Tegra30, so add the offset as part of SoC data structure.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
PRSNT_MAP bit field is programmed to update the slot present status.
PRSNT_SENSE IRQ is triggered when this bit field is programmed, which is
not an error. Add a new if condition to trap PRSNT_SENSE code and print
it with debug log level.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Cacheable upstream transactions are supported in Tegra20 and Tegra186
only.
AFI_CACHE_BAR_{0,1}_{ST,SZ} registers are available in Tegra20 to
support cacheable upstream transactions. In Tegra186, AFI_AXCACHE
register is defined instead of AFI_CACHE_BAR_{0,1}_{ST,SZ} to be in line
with its memory subsystem design.
Therefore, program AFI_CACHE_BAR_{0,1}_{ST,SZ} registers only for Tegra20.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Disable controllers which failed to bring the link up and configure
CLKREQ# signals of these controllers as GPIO. This is required to avoid
CLKREQ# signal of inactive controllers interfering with PLLE power down
sequence.
PCIE_CLKREQ_GPIO bits are defined only in Tegra186, however programming
these bits in other SoCs doesn't cause any side effects. Program these
bits for all Tegra SoCs to avoid a conditional check.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Bjorn Helgaas
YueHaibing
Hou Zhiqiang
Leonard Crestez
Dexuan Cui
Vidya Sagar
Manikanta Maddireddy
Bharat Kumar Gogada