All uses of the v4l2_clk API so far only register one clock with a fixed
name. This allows us to get rid of it, which also will make CCF and DT
integration easier.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add lane_polarities field to struct v4l2_of_bus_mipi_csi2 and write the
contents of the lane-polarities property to it. The field tells the polarity
of the physical lanes starting from the first one. Any unused lanes are
ignored, i.e. only the polarity of the used lanes is specified.
Also rework reading the "data-lanes" property a little.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The video port clock is l3_ick divided by vpclk_div. This clock must be high
enough for the external pixel rate. The video port requires two clock cycles
to process a pixel.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make omap3isp configuration data structures more suitable for consumption by
the DT by separating the I2C bus information of all the sub-devices in a
group and the ISP bus information from each other. The ISP bus information
is made a pointer instead of being directly embedded in the struct.
In the case of the DT only the sensor specific information on the ISP bus
configuration is retained. The structs are renamed to reflect that.
After this change the structs needed to describe device configuration can be
allocated and accessed separately without those needed only in the case of
platform data. The platform data related structs can be later removed once
the support for platform data can be removed.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Igor Grinberg <grinberg@compulab.co.il> (for cm-t35)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The video and pad ops are duplicates, so get rid of the more limited video op.
The whole point of the subdev API is to allow reuse of subdev drivers by
bridge drivers. Having duplicate ops makes that much harder. We should never
have allowed duplicate ops in the first place. A lesson for the future.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If a subdevice pad op is called from a bridge driver, then there is
no v4l2_subdev_fh struct that can be passed to the subdevice. This
made it hard to use such subdevs from a bridge driver.
This patch replaces the v4l2_subdev_fh pointer by a v4l2_subdev_pad_config
pointer in the pad ops. This allows bridge drivers to use the various
try_ pad ops by creating a v4l2_subdev_pad_config struct and passing it
along to the pad op.
The v4l2_subdev_get_try_* macros had to be changed because of this, so
I also took the opportunity to use the full name of the v4l2_subdev_get_try_*
functions in the __V4L2_SUBDEV_MK_GET_TRY macro arguments: if you now do
'git grep v4l2_subdev_get_try_format' you will actually find the header
where it is defined.
One remark regarding the drivers/staging/media/davinci_vpfe patches: the
*_init_formats() functions assumed that fh could be NULL. However, that's
not true for this driver, it's always set. This is almost certainly a copy
and paste from the omap3isp driver. I've updated the code to reflect the
fact that fh is never NULL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The handling of VIDIOC_G/S_PRIORITY is now entirely done by the V4L2
core, so we can drop the g/s_priority ioctl ops.
We do have to make sure though that when S_PRIORITY is called we check
that the driver used struct v4l2_fh. This check can be removed once all
drivers are converted to that structure.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
To keep V4L2 drivers that did not yet convert to unlocked_ioctl happy,
the v4l2 core had a .ioctl file operation that took a V4L2 lock.
The last drivers are now converted to unlocked_ioctl, so all this
old code can now be removed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is confusing which parts of the driver are adv7604 specific, adv7611
specific or common for both. This patch renames any adv7604 prefixes (both
for functions and defines) to adv76xx whenever they are common.
Signed-off-by: Pablo Anton <pablo.anton@vodalys-labs.com>
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
[hans.verkuil@cisco.com: rebased and renamed ADV76xx_fsc to ADV76XX_FSC]
[hans.verkuil@cisco.com: kept the existing adv7604 driver name]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The burst length could be BEATS_4/8/16. Before this patch, isi use default
value BEATS_4. To imporve the performance we could set it to BEATS_16.
Otherwise sometime it would cause the ISI overflow error.
Reported-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The previous provision for DVB media controller support were to
define an ID (likely meaning the adapter number) for the DVB
devnodes.
This is just plain wrong. Just like V4L, DVB devices (and any other
device node)) are uniquely identified via a (major, minor) tuple.
This is enough to uniquely identify a devnode, no matter what
API it implements.
So, before we go too far, let's mark the old v4l, fb, dvb and alsa
"devnode" info as deprecated, and just call it as "dev".
We can latter add fields specific to each API if needed.
As we don't want to break compilation on already existing apps,
let's just keep the old definitions as-is, adding a note that
those are deprecated at media-entity.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Split ioctl interface from enum_freq_bands, g_tuner and s_hw_freq_seek
functions and export them to be used in other drivers like bttv.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The videobuf_dma_init* and videobuf_dma_map() functions are no longer
used except in videobuf-dma-sg.c itself. Make them static.
These functions were abused in various drivers. All those drivers
have now been fixed, so by no longer exporting these functions
future abuse is now prevented.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The old debug field is renamed to dev_debug to ensure that existing drivers
(including out-of-tree drivers) that try to use the old name will no longer
compile. A comment has also been added that makes it explicit that drivers
shouldn't use this field.
Additional bits have been added to the debug flag to be more fine-grained
when debugging, especially when dealing with streaming ioctls and read,
write and poll. You want to enable those explicitly to prevent flooding
the log when streaming unless you actually want to do that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Weird, this op isn't used at all. Seems to be orphaned code.
Remove it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Drop the duplicate get/set_crop pad ops and only use get/set_selection.
It makes no sense to have two duplicate ops in the internal subdev API.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
1) This is not allowed by the kernel coding style
2) Just configure your editor correctly
3) It's really ugly
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add and copy the new ycbcr_enc and quantization fields.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Require that dma-sg also uses an allocation context. This is in preparation
for adding prepare/finish memops to sync the memory between DMA and CPU.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is needed for the next patch where the dma-sg alloc memop needs
to know the dma_dir.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The 'write' argument is very ambiguous. I first assumed that if it is 1,
then we're doing video output but instead it meant the reverse.
Since it is used to setup the dma_dir value anyway it is now replaced by
the correct dma_dir value which is unambiguous.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Document that drivers can access/modify the buffer contents in buf_prepare
and buf_finish. That was not clearly stated before.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2_ctrl_check() helper function is now only used in cx2341x.
Move it there and make it static.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
For some unknown reason several control prototypes where in v4l2-common.c
instead of in v4l2-ctrls.h. Move them and document them.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Several control helper functions are no longer needed since most drivers
are now converted to the control framework. So we can delete them.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove unreferenced members from the platform
data's structure.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add device tree support by changing the device registration order.
In the device tree the si4713 node is a normal I2C device, which
will be probed as such. Thus the V4L device must be probed from
the I2C device and not the other way around.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to have subsytem agnostic media bus format definitions we've
moved media bus definition to include/uapi/linux/media-bus-format.h and
prefixed values with MEDIA_BUS_FMT instead of V4L2_MBUS_FMT.
Reference new definitions in all platform drivers.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace references to the v4l2_mbus_pixelcode enum with the new
media_bus_format enum in all common headers.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch adds support for vidioc_create_bufs. Along side
remove unneeded member numbuffers.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We can use kfifo_initialized() to check if the fifo in lirc_buffer is
initialized or not. There's no need to have a dedicated fifo status
variable in lirc_buffer.
[m.chehab@samsung.com: add the same change to lirc_zilog, to avoid
breaking compilation of staging drivers]
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch uses vb2_is_busy() helper to check if streaming is
actually started, instead of driver managing it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch converts the driver to use fh handling provided by the
v4l core instead of driver doing it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This RC will be used by DVBSky driver, added on the next patch.
Signed-off-by: Nibble Max <nibble.max@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The buffer flags are incorrectly referred to as V4L2_BUF_FLAGS_* instead
of V4L2_BUF_FLAG_* in comments. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The recent conversion of saa7134 to vb2 unconvered a poll() bug that
broke the teletext applications alevt and mtt. These applications
expect that calling poll() without having called VIDIOC_STREAMON will
cause poll() to return POLLERR. That did not happen in vb2.
This patch fixes that behavior. It also fixes what should happen when
poll() is called when STREAMON is called but no buffers have been
queued. In that case poll() will also return POLLERR, but only for
capture queues since output queues will always return POLLOUT
anyway in that situation.
This brings the vb2 behavior in line with the old videobuf behavior.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The comment for start_streaming that tells the developer with which vb2 state
buffers should be returned to vb2 gave the wrong state. Very confusing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch adds a helper to get the status if start_streaming()
was called successfully.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Pawel Osciak <pawel@osciak.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The fpc_table_addr is used as an unsigned integer that stores
an address. At the Kernel, the proper type for such integers
is unsigned long.
This generates lots of warnings when compiling on 64 bits.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The following lockdep warning has been there ever since commit a517cca6b2
one year ago:
[ 403.117947] ======================================================
[ 403.117949] [ INFO: possible circular locking dependency detected ]
[ 403.117953] 3.16.0-rc6-test-media #961 Not tainted
[ 403.117954] -------------------------------------------------------
[ 403.117956] v4l2-ctl/15377 is trying to acquire lock:
[ 403.117959] (&dev->mutex#3){+.+.+.}, at: [<ffffffffa005a6c3>] vb2_fop_mmap+0x33/0x90 [videobuf2_core]
[ 403.117974]
[ 403.117974] but task is already holding lock:
[ 403.117976] (&mm->mmap_sem){++++++}, at: [<ffffffff8118291f>] vm_mmap_pgoff+0x6f/0xc0
[ 403.117987]
[ 403.117987] which lock already depends on the new lock.
[ 403.117987]
[ 403.117990]
[ 403.117990] the existing dependency chain (in reverse order) is:
[ 403.117992]
[ 403.117992] -> #1 (&mm->mmap_sem){++++++}:
[ 403.117997] [<ffffffff810d733c>] validate_chain.isra.39+0x5fc/0x9a0
[ 403.118006] [<ffffffff810d8bc3>] __lock_acquire+0x4d3/0xd30
[ 403.118010] [<ffffffff810d9da7>] lock_acquire+0xa7/0x160
[ 403.118014] [<ffffffff8118c9ec>] might_fault+0x7c/0xb0
[ 403.118018] [<ffffffffa0028a25>] video_usercopy+0x425/0x610 [videodev]
[ 403.118028] [<ffffffffa0028c25>] video_ioctl2+0x15/0x20 [videodev]
[ 403.118034] [<ffffffffa0022764>] v4l2_ioctl+0x184/0x1a0 [videodev]
[ 403.118040] [<ffffffff811d77d0>] do_vfs_ioctl+0x2f0/0x4f0
[ 403.118307] [<ffffffff811d7a51>] SyS_ioctl+0x81/0xa0
[ 403.118311] [<ffffffff8199dc69>] system_call_fastpath+0x16/0x1b
[ 403.118319]
[ 403.118319] -> #0 (&dev->mutex#3){+.+.+.}:
[ 403.118324] [<ffffffff810d6a96>] check_prevs_add+0x746/0x9f0
[ 403.118329] [<ffffffff810d733c>] validate_chain.isra.39+0x5fc/0x9a0
[ 403.118333] [<ffffffff810d8bc3>] __lock_acquire+0x4d3/0xd30
[ 403.118336] [<ffffffff810d9da7>] lock_acquire+0xa7/0x160
[ 403.118340] [<ffffffff81999664>] mutex_lock_interruptible_nested+0x64/0x640
[ 403.118344] [<ffffffffa005a6c3>] vb2_fop_mmap+0x33/0x90 [videobuf2_core]
[ 403.118349] [<ffffffffa0022122>] v4l2_mmap+0x62/0xa0 [videodev]
[ 403.118354] [<ffffffff81197270>] mmap_region+0x3d0/0x5d0
[ 403.118359] [<ffffffff8119778d>] do_mmap_pgoff+0x31d/0x400
[ 403.118363] [<ffffffff81182940>] vm_mmap_pgoff+0x90/0xc0
[ 403.118366] [<ffffffff81195cef>] SyS_mmap_pgoff+0x1df/0x2a0
[ 403.118369] [<ffffffff810085c2>] SyS_mmap+0x22/0x30
[ 403.118376] [<ffffffff8199dc69>] system_call_fastpath+0x16/0x1b
[ 403.118381]
[ 403.118381] other info that might help us debug this:
[ 403.118381]
[ 403.118383] Possible unsafe locking scenario:
[ 403.118383]
[ 403.118385] CPU0 CPU1
[ 403.118387] ---- ----
[ 403.118388] lock(&mm->mmap_sem);
[ 403.118391] lock(&dev->mutex#3);
[ 403.118394] lock(&mm->mmap_sem);
[ 403.118397] lock(&dev->mutex#3);
[ 403.118400]
[ 403.118400] *** DEADLOCK ***
[ 403.118400]
[ 403.118403] 1 lock held by v4l2-ctl/15377:
[ 403.118405] #0: (&mm->mmap_sem){++++++}, at: [<ffffffff8118291f>] vm_mmap_pgoff+0x6f/0xc0
[ 403.118411]
[ 403.118411] stack backtrace:
[ 403.118415] CPU: 0 PID: 15377 Comm: v4l2-ctl Not tainted 3.16.0-rc6-test-media #961
[ 403.118418] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 07/31/2013
[ 403.118420] ffffffff82a6c9d0 ffff8800af37fb00 ffffffff819916a2 ffffffff82a6c9d0
[ 403.118425] ffff8800af37fb40 ffffffff810d5715 ffff8802308e4200 0000000000000000
[ 403.118429] ffff8802308e4a48 ffff8802308e4a48 ffff8802308e4200 0000000000000001
[ 403.118433] Call Trace:
[ 403.118441] [<ffffffff819916a2>] dump_stack+0x4e/0x7a
[ 403.118445] [<ffffffff810d5715>] print_circular_bug+0x1d5/0x2a0
[ 403.118449] [<ffffffff810d6a96>] check_prevs_add+0x746/0x9f0
[ 403.118455] [<ffffffff8119c172>] ? find_vmap_area+0x42/0x70
[ 403.118459] [<ffffffff810d733c>] validate_chain.isra.39+0x5fc/0x9a0
[ 403.118463] [<ffffffff810d8bc3>] __lock_acquire+0x4d3/0xd30
[ 403.118468] [<ffffffff810d9da7>] lock_acquire+0xa7/0x160
[ 403.118472] [<ffffffffa005a6c3>] ? vb2_fop_mmap+0x33/0x90 [videobuf2_core]
[ 403.118476] [<ffffffffa005a6c3>] ? vb2_fop_mmap+0x33/0x90 [videobuf2_core]
[ 403.118480] [<ffffffff81999664>] mutex_lock_interruptible_nested+0x64/0x640
[ 403.118484] [<ffffffffa005a6c3>] ? vb2_fop_mmap+0x33/0x90 [videobuf2_core]
[ 403.118488] [<ffffffffa005a6c3>] ? vb2_fop_mmap+0x33/0x90 [videobuf2_core]
[ 403.118493] [<ffffffff810d8055>] ? mark_held_locks+0x75/0xa0
[ 403.118497] [<ffffffffa005a6c3>] vb2_fop_mmap+0x33/0x90 [videobuf2_core]
[ 403.118502] [<ffffffffa0022122>] v4l2_mmap+0x62/0xa0 [videodev]
[ 403.118506] [<ffffffff81197270>] mmap_region+0x3d0/0x5d0
[ 403.118510] [<ffffffff8119778d>] do_mmap_pgoff+0x31d/0x400
[ 403.118513] [<ffffffff81182940>] vm_mmap_pgoff+0x90/0xc0
[ 403.118517] [<ffffffff81195cef>] SyS_mmap_pgoff+0x1df/0x2a0
[ 403.118521] [<ffffffff810085c2>] SyS_mmap+0x22/0x30
[ 403.118525] [<ffffffff8199dc69>] system_call_fastpath+0x16/0x1b
The reason is that vb2_fop_mmap and vb2_fop_get_unmapped_area take the core lock
while they are called with the mmap_sem semaphore held. But elsewhere in the code
the core lock is taken first but calls to copy_to/from_user() can take the mmap_sem
semaphore as well, potentially causing a classical A-B/B-A deadlock.
However, the mmap/get_unmapped_area calls really shouldn't take the core lock
at all. So what would happen if they don't take the core lock anymore?
There are two situations that need to be taken into account: calling mmap while
new buffers are being added and calling mmap while buffers are being deleted.
The first case works almost fine without a lock: in all cases mmap relies on
correctly filled-in q->num_buffers/q->num_planes values and those are only
updated by reqbufs and create_buffers *after* any new buffers have been
initialized completely. Except in one case: if an error occurred while allocating
the buffers it will increase num_buffers and rely on __vb2_queue_free to
decrease it again. So there is a short period where the buffer information
may be wrong.
The second case definitely does pose a problem: buffers may be in the process
of being deleted, without the internal structure being updated.
In order to fix this a new mutex is added to vb2_queue that is taken when
buffers are allocated or deleted, and in vb2_mmap. That way vb2_mmap won't
get stale buffer data. Note that this is a problem only for MEMORY_MMAP, so
even though __qbuf_userptr and __qbuf_dmabuf also mess around with buffers
(mem_priv in particular), this doesn't clash with vb2_mmap or
vb2_get_unmapped_area since those are MMAP specific.
As an additional bonus the hack in __buf_prepare, the USERPTR case, can be
removed as well since mmap() no longer takes the core lock.
All in all a much cleaner solution.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When the CCDC input is interlaced enable the alternate field order on
the CCDC output video node. The field signal polarity is specified
through platform data.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Enrico Butera <ebutera@users.sourceforge.net>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This protocol is found on Dreambox remotes
[m.chehab@samsung.com: CodingStyle fixes and conflict fix]
Signed-off-by: Marcel Mol <marcel@mesa.nl>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Multiple pinctrl states are defined for 8, 16 and 24 data pin groups in PPI peripheral.
The driver should select correct group before set up further PPI parameters.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
if the pinctrl driver is enabled.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Patch originally written by Konrad. Rebased on current linux media tree.
Under Xen, vmalloc_32() isn't guaranteed to return pages which are really
under 4G in machine physical addresses (only in virtual pseudo-physical
addresses). To work around this, implement a vmalloc variant which
allocates each page with dma_alloc_coherent() to guarantee that each
page is suitable for the device in question.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: James Harper <james.harper@ejbdigital.com.au>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The hole point of IR_dprintk() is that, once a level is
given at debug parameter, all enabled IR parsers will show their
debug messages.
While converting it to dynamic_printk might be a good idea,
right now it just makes very hard to debug the drivers, as
one needs to both pass debug=1 or debug=2 to rc-core and
to use the dynamic printk to enable all the desired lines.
That doesn't make sense!
So, revert to the old way, as a single line is changed,
and the debug parameter will now work as expected.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The si4713 supports several RDS features not yet implemented in the driver.
This patch adds the missing RDS functionality to the list of RDS controls.
The ALT_FREQS control is a compound control containing an array of up
to 25 (the maximum according to the RDS standard) frequencies. To support
that the V4L2_CTRL_TYPE_U32 was added.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
A lot of work was done in vb2 to regulate how drivers and the vb2 core handle
buffer ownership, but inexplicably the videobuf2-core.h comments were never
updated. Do so now. The same was true for the replacement of the -ENOBUFS
mechanism by the min_buffers_needed field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rather than always having to use a v4l2_ext_control struct to set
a control value from within a driver, switch to just setting the
new value. This is faster and it makes it possible to set more
complex types such as a string control as is added by this
patch.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We already have dev->scancode_filter and dev->scancode_wakeup_filter
so rename dev->scanmask to dev->scancode_mask for consistency.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The basic API of rc-core used to be:
dev = rc_allocate_device();
dev->x = a;
dev->y = b;
dev->z = c;
rc_register_device();
which is a pretty common pattern in the kernel, after the introduction of
protocol arrays the API looks something like:
dev = rc_allocate_device();
dev->x = a;
rc_set_allowed_protocols(dev, RC_BIT_X);
dev->z = c;
rc_register_device();
There's no real need for the protocols to be an array, so change it
back to be consistent (and in preparation for the following patches).
[m.chehab@samsung.com: added missing changes at some files]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Right now the protocol information is not preserved, rc-core gets handed a
scancode but has no idea which protocol it corresponds to.
This patch (which required reading through the source/keymap for all drivers,
not fun) makes the protocol information explicit which is important
documentation and makes it easier to e.g. support multiple protocols with one
decoder (think rc5 and rc-streamzap). The information isn't used yet so there
should be no functional changes.
[m.chehab@samsung.com: rebased, added cxusb and removed bad whitespacing]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The arguments used for ir-kbd-i2c's get_key() functions are not
really suited for rc-core and the ir_raw/ir_key distinction is
just confusing.
Convert all of them to return a protocol/scancode/toggle triple instead.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some drivers might allow to decode remaining frames from an internal ringbuffer
after a decoder stop command. Allow those to call v4l2_m2m_try_schedule
directly.
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement unlocked variants of v4l2_ctrl_s_ctrl() and
v4l2_ctrl_s_ctrl_int64(). As drivers need to set controls as they access
driver internal state elsewhere than in the control framework unlocked
variants of these functions become handy.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Drivers may use the v4l2_ctrl_modify_range() internally as part of other
operations that need to be both serialised using a driver's lock which can
also be used to serialise access to the control handler. Provide an unlocked
version of the function, __v4l2_ctrl_modify_range() which then may be used
by drivers for the purpose.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The v4l2_ctrl_{,un}lock will be needed elsewhere. Define them before the
functions that perform operations on controls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When a fatal error occurs that render the device unusable, the only
options for a driver to signal the error condition to userspace is to
set the V4L2_BUF_FLAG_ERROR flag when dequeuing buffers and to return an
error from the buffer prepare handler when queuing buffers.
The buffer error flag indicates a transient error and can't be used by
applications to detect fatal errors. Returning an error from vb2_qbuf()
is thus the only real indication that a fatal error occurred. However,
this is difficult to handle for multithreaded applications that requeue
buffers from a thread other than the control thread. In particular the
poll() call in the control thread will not notify userspace of the
error.
This patch adds an explicit mechanism to report fatal errors to
userspace. Drivers can call the vb2_queue_error() function to signal a
fatal error. From this moment on, buffer preparation will return -EIO to
userspace, and vb2_poll() will set the POLLERR flag and return
immediately. The error flag is cleared when cancelling the queue, either
at stream off time (through vb2_streamoff) or when releasing the queue
with vb2_queue_release().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
These are needed by the upcoming patches for the motion detection
matrices.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add core support for N-dimensional arrays.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add dims, nr_of_dims and elems fields to the core control structures in preparation
for N-dimensional array support.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rather than having two unions for all types just keep 'val' and
'cur.val' and use the p_cur and p_new unions to access all others.
The only reason for keeping 'val' and 'cur.val' is that it is used
all over, so converting this as well would be a huge job.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When setting a control the control's new value is compared to the current
value twice: once by new_to_cur(), once by cluster_changed(). Not a big
deal when dealing with simple values, but it can be a problem when dealing
with compound types or arrays. So fix this: cluster_changed() sets the
has_changed flag, which is used by new_to_cur() instead of having to do
another compare.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Since compound controls can have non-standard types we need to be able to do
type-specific checks etc. In order to make that easy type operations are added.
There are four operations:
- equal: check if two values are equal
- init: initialize a value
- log: log the value
- validate: validate a new value
The v4l2_ctrl struct adds p_new and p_cur unions at the end of the struct.
This union provides a standard way of accessing control types through a pointer,
which greatly simplifies internal control processing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add the v4l2 core plumbing for the new VIDIOC_QUERY_EXT_CTRL ioctl.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch implements initial support for compound types.
The changes are fairly obvious: basic support for is_ptr types, the
type_is_int function is replaced by a is_int bitfield, and
v4l2_query_ext_ctrl is added.
Note that this patch does not yet add support for N-dimensional
arrays, that comes later. So v4l2_query_ext_ctrl just sets elems to
1 and nr_of_dims and dims[] are all zero.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
While VIDIOC_QUERYCTRL is limited to 32 bit min/max/step/def values
for controls, the upcoming VIDIOC_QUERY_EXT_CTRL isn't. So increase
the internal representation to 64 bits in preparation.
Because of these changes the msi3101 driver has been modified slightly
to fix a formatting issue (%d becomes %lld), vivi had to be modified
as well to cope with the new 64-bit min/max values and the PIXEL_RATE
control in a few sensor drivers required proper min/max/def values.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Since none of the drivers are using it, this flag can be removed.
Signed-off-by: Ramakrishnan Muthukrishnan <ramakrmu@cisco.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull OMAP3 updates from Mauro Carvalho Chehab:
"Some driver improvements on OMAP3. This series depend on some iommu
patches already merged"
* 'topic/omap3isp' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (26 commits)
[media] omap3isp: Rename isp_buffer isp_addr field to dma
[media] omap3isp: Move to videobuf2
[media] v4l: vb2: Add a function to discard all DONE buffers
[media] omap3isp: Cancel all queued buffers when stopping the video stream
[media] omap3isp: Move buffer irqlist to isp_buffer structure
[media] omap3isp: Move queue irqlock to isp_video structure
[media] omap3isp: Move queue mutex to isp_video structure
[media] omap3isp: queue: Don't build scatterlist for kernel buffer
[media] omap3isp: Use the ARM DMA IOMMU-aware operations
[media] omap3isp: queue: Use sg_alloc_table_from_pages()
[media] omap3isp: queue: Map PFNMAP buffers to device
[media] omap3isp: queue: Fix the dma_map_sg() return value check
[media] omap3isp: queue: Allocate kernel buffers with dma_alloc_coherent
[media] omap3isp: queue: Inline the ispmmu_v(un)map functions
[media] omap3isp: queue: Merge the prepare and sglist functions
[media] omap3isp: queue: Use sg_table structure
[media] omap3isp: queue: Move IOMMU handling code to the queue
[media] omap3isp: video: Set the buffer bytesused field at completion time
[media] omap3isp: ccdc: Use the DMA API for FPC
[media] omap3isp: ccdc: Use the DMA API for LSC
...
Add an inv_llc_pol field to platform data to control the clock polarity.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
And set input routing when initializing the device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This allows replacing duplicate code blocks by loops over the arrays.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated
and unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace the dummy video format operations by pad format operations that
configure the output format.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The ADV7604 has sink pads for its HDMI and analog inputs. Report them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds support for the Analog Devices ADV7611 HDMI receiver.
The adv7611 is quite similar to the adv7604. It has only one instead of four
HDMI inputs and no analog frontend though. Also some register bits have been
shuffled around, but large parts of their register maps are compatible.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The file is using u8 which is defined in linux/types.h.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The dv_timings_cap and enum_dv_timings subdev operations are implemented
at the device level, but apply to pads. Create new variants of those
operations at the pad level. The device level variants will be removed
once all drivers are ported to the pad level DT timings operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When suspending a device while a video stream is active all buffers
marked as done but not dequeued yet will be kept across suspend and
given back to userspace after resume. This will result in outdated
buffers being dequeued.
Introduce a new vb2 function to mark all done buffers as erroneous
instead, to be used by drivers at resume time.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The g_std and s_std operations are video-related, move them to the video
ops where they belong.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This event indicates that the video device has encountered
a source parameter change during runtime. This can typically be a
resolution change detected by a video decoder OR a format change
detected by an input connector.
This needs to be nofified to the userspace and the application may
be expected to reallocate buffers before proceeding. The application
can subscribe to events on a specific pad or input port which
it is interested in.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
All platforms supported by this driver are going to get device tree
support in this kernel release so remove code that would have been
actually not used any more.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
While there was already a g_tvnorms_output video op, it's counterpart for
video capture was missing. Add it.
This is necessary for generic bridge drivers like soc-camera to set the
video_device tvnorms field correctly. Otherwise ENUMSTD cannot work.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
V4L2_MBUS_FRAME_DESC_FL_BLOB intends to say the receiver must use 1D DMA to
receive the image, as the format does not have line offsets. This typically
includes all compressed formats.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When the sub-device is registered, increment the use count of the sub-device
owner only if it's different from the owner of the driver for the media
device. This avoids increasing the use count by the module itself and thus
making it possible to unload it when it's not in use.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
mdev->fops->owner is actually the owner of the very same module which
implements media_device_register(), so it can't be unloaded anyway. Instead,
use THIS_MODULE through a macro as does video_register_device().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The vb2 core ignores any return code from the stop_streaming op.
And there really isn't anything it can do anyway in case of an error.
So change the return type to void and update any drivers that implement it.
The int return gave drivers the idea that this operation could actually
fail, but that's really not the case.
The pwc amd sdr-msi3101 drivers both had this construction:
if (mutex_lock_interruptible(&s->v4l2_lock))
return -ERESTARTSYS;
This has been updated to just call mutex_lock(). The stop_streaming op
expects this to really stop streaming and I very much doubt this will
work reliably if stop_streaming just returns without really stopping the
DMA.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
With the new vb2_thread_start/stop core code it is very easy to implement
videobuf2-dvb. This should simplify converting existing videobuf drivers to
vb2.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In order to implement vb2 DVB support you need to be able to start
a kernel thread that queues and dequeues buffers, calling a callback
function for every buffer. This patch adds support for that.
It's based on drivers/media/v4l2-core/videobuf-dvb.c, but with all the DVB
specific stuff stripped out, thus making it much more generic.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Added a vb2_fileio_is_active inline function that returns true if fileio
is in progress. Check for this too in mmap() (you don't want apps mmap()ing
buffers used by fileio) and expbuf() (same reason).
In addition drivers should be able to check for this in queue_setup() to
return an error if an attempt is made to read() or write() with
V4L2_FIELD_ALTERNATE being configured. This is illegal (there is no way
to pass the TOP/BOTTOM information around using file I/O).
However, in order to be able to check for this the init_fileio function
needs to set q->fileio early on, before the buffers are allocated. So switch
to using internal functions (__reqbufs, vb2_internal_qbuf and
vb2_internal_streamon) to skip the fileio check. Well, that's why the internal
functions were created...
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch migrates the vpfe driver to use v4l2_fh for
priority handling.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch migrates the vpbe driver to use v4l2_fh for
priority handling. This also fixes v4l2-compliance test.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The notify function is a void function, yet the v4l2_subdev_notify
define uses it in a ? : construction, which causes sparse warnings.
Replace the define by a static inline function and move it to
v4l2-device.h, which is where it belongs since it needs to know the
v4l2_device struct. This wasn't a problem when it was a define, but
as a static inline function this no longer compiles in v4l2-subdev.h.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The generic scancode filtering has questionable value and makes it
impossible to determine from userspace if there is an actual
scancode hw filter present or not.
So revert the generic parts.
Based on a patch from James Hogan <james.hogan@imgtec.com>, but this
version also makes sure that only the valid sysfs files are created
in the first place.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Overloading dev->s_filter to do two different functions (set wakeup filters
and generic hardware filters) makes it impossible to tell what the
hardware actually supports, so create a separate dev->s_wakeup_filter and
make the distinction explicit.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media updates from Mauro Carvalho Chehab:
"The main set of series of patches for media subsystem, including:
- document RC sysfs class
- added an API to setup scancode to allow waking up systems using the
Remote Controller
- add API for SDR devices. Drivers are still on staging
- some API improvements for getting EDID data from media
inputs/outputs
- new DVB frontend driver for drx-j (ATSC)
- one driver (it913x/it9137) got removed, in favor of an improvement
on another driver (af9035)
- added a skeleton V4L2 PCI driver at documentation
- added a dual flash driver (lm3646)
- added a new IR driver (img-ir)
- added an IR scancode decoder for the Sharp protocol
- some improvements at the usbtv driver, to allow its core to be
reused.
- added a new SDR driver (rtl2832u_sdr)
- added a new tuner driver (msi001)
- several improvements at em28xx driver to fix PM support, device
removal and to split the V4L2 specific bits into a separate
sub-driver
- one driver got converted to videobuf2 (s2255drv)
- the e4000 tuner driver now follows an improved binding model
- some fixes at V4L2 compat32 code
- several fixes and enhancements at videobuf2 code
- some cleanups at V4L2 API documentation
- usual driver enhancements, new board additions and misc fixups"
[ NOTE! This merge effective drops commit 4329b93b28 ("of: Reduce
indentation in of_graph_get_next_endpoint").
The of_graph_get_next_endpoint() function was moved and renamed by
commit fd9fdb78a9 ("[media] of: move graph helpers from
drivers/media/v4l2-core to drivers/of"). It was originally called
v4l2_of_get_next_endpoint() and lived in the file
drivers/media/v4l2-core/v4l2-of.c.
In that original location, it was then fixed to support empty port
nodes by commit b9db140c1e ("[media] v4l: of: Support empty port
nodes"), and that commit clashes badly with the dropped "Reduce
intendation" commit. I had to choose one or the other, and decided
that the "Support empty port nodes" commit was more important ]
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (426 commits)
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
Revert "[media] em28xx-dvb: fix PCTV 461e tuner I2C binding"
[media] em28xx: fix PCTV 290e LNA oops
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
[media] m88ds3103: fix bug on .set_tone()
[media] saa7134: fix WARN_ON during resume
[media] v4l2-dv-timings: add module name, description, license
[media] videodev2.h: add parenthesis around macro arguments
[media] saa6752hs: depends on CRC32
[media] si4713: fix Kconfig dependencies
[media] Sensoray 2255 uses videobuf2
[media] adv7180: free an interrupt on failure paths in init_device()
[media] e4000: make VIDEO_V4L2 dependency optional
[media] af9033: Don't export functions for the hardware filter
[media] af9035: use af9033 PID filters
[media] af9033: implement PID filter
[media] rtl2832_sdr: do not use dynamic stack allocation
[media] e4000: fix 32-bit build error
[media] em28xx-audio: make sure audio is unmuted on open()
[media] DocBook media: v4l2_format_sdr was renamed to v4l2_sdr_format
...
Add VIDIOC_ENUM_FREQ_BANDS, enumerate supported frequency bands,
IOCTL support for sub-device tuners too.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a wakeup_protocols sysfs file which controls the new
rc_dev::enabled_protocols[RC_FILTER_WAKEUP], which is the mask of
protocols that are used for the wakeup filter.
A new RC driver callback change_wakeup_protocol() is called to change
the wakeup protocol mask.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Only a single allowed and enabled protocol mask currently exists in
struct rc_dev, however to support a separate wakeup filter protocol two
of each are needed, ideally as an array.
Therefore make both rc_dev::allowed_protos and rc_dev::enabled_protocols
arrays, update all users to reference the first element
(RC_FILTER_NORMAL), and add a couple more helper functions for drivers
to use for setting the allowed and enabled wakeup protocols.
We also rename allowed_protos to allowed_protocols while we're at it,
which is more consistent with enabled_protocols.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The allowed and enabled protocol masks need to be expanded to be per
filter type in order to support wakeup filter protocol selection. To
ease that process abstract access to the rc_dev::allowed_protos and
rc_dev::enabled_protocols members with inline functions.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Support this ioctl as part of the v4l2 core. Use the new ioctl
name and struct v4l2_edid type in the existing core code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds the driver for the LM3646, dual LED Flash driver.
The LM3646 has two 1.5A sync. boost converter with dual white current source.
It is controlled via an I2C compatible interface.
Each flash brightness, torch brightness and enable/disable can be controlled.
Under voltage, input voltage monitor and thermal threshhold Faults are added.
Please refer the datasheet http://www.ti.com/lit/ds/snvs962/snvs962.pdf
Signed-off-by: Daniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In commit 02f142ecd2 support was added to
start_streaming to return -ENOBUFS if insufficient buffers were queued
for the DMA engine to start. The vb2 core would attempt calling
start_streaming again if another buffer would be queued up.
Later analysis uncovered problems with the queue management if start_streaming
would return an error: the buffers are enqueued to the driver before the
start_streaming op is called, so after an error they are never returned to
the vb2 core. The solution for this is to let the driver return them to
the vb2 core in case of an error while starting the DMA engine. However,
in the case of -ENOBUFS that would be weird: it is not a real error, it
just says that more buffers are needed. Requiring start_streaming to give
them back only to have them requeued again the next time the application
calls QBUF is inefficient.
This patch changes this mechanism: it adds a 'min_buffers_needed' field
to vb2_queue that drivers can set with the minimum number of buffers
required to start the DMA engine. The start_streaming op is only called
if enough buffers are queued. The -ENOBUFS handling has been dropped in
favor of this new method.
Drivers are expected to return buffers back to vb2 core with state QUEUED
if start_streaming would return an error. The vb2 core checks for this
and produces a warning if that didn't happen and it will forcefully
reclaim such buffers to ensure that the internal vb2 core state remains
consistent and all buffer-related resources have been correctly freed
and all op calls have been balanced.
__reqbufs() has been updated to check that at least min_buffers_needed
buffers could be allocated. If fewer buffers were allocated then __reqbufs
will free what was allocated and return -ENOMEM. Based on a suggestion from
Pawel Osciak.
__create_bufs() doesn't do that check, since the use of __create_bufs
assumes some advance scenario where the user might want more control.
Instead streamon will check if enough buffers were allocated to prevent
streaming with fewer than the minimum required number of buffers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
'queued_count' is a bit vague since it is not clear to which queue it
refers to: the vb2 internal list of buffers or the driver-owned list
of buffers.
Rename to make it explicit.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Sometimes sentences in comments ended with a period, and sometimes they
didn't. Add periods. No other changes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If a queue was canceled, then the buf_finish op was never called for the
pending buffers. So add this call to queue_cancel. Before calling buf_finish
set the buffer state to PREPARED, which is the correct state. That way the
states DONE and ERROR will only be seen in buf_finish if streaming is in
progress.
Since buf_finish can now be called from non-streaming state we need to
adapt the handful of drivers that actually need to know this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The buf_finish op should always work, so change the return type to void.
Update the few drivers that use it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When a vb2_queue is freed check if all the mem_ops and queue ops were balanced.
So the number of calls to e.g. buf_finish has to match the number of calls to
buf_prepare, etc.
This code is only enabled if CONFIG_VIDEO_ADV_DEBUG is set.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds a new struct of_endpoint which is then embedded in struct
v4l2_of_endpoint and contains the endpoint properties that are not V4L2
(or even media) specific: the port number, endpoint id, local device tree
node and remote endpoint phandle. of_graph_parse_endpoint parses those
properties and is used by v4l2_of_parse_endpoint, which just adds the
V4L2 MBUS information to the containing v4l2_of_endpoint structure.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch moves the parsing helpers used to parse connected graphs
in the device tree, like the video interface bindings documented in
Documentation/devicetree/bindings/media/video-interfaces.txt, from
drivers/media/v4l2-core/v4l2-of.c into drivers/of/base.c.
This allows to reuse the same parser code from outside the V4L2
framework, most importantly from display drivers.
The functions v4l2_of_get_next_endpoint, v4l2_of_get_remote_port,
and v4l2_of_get_remote_port_parent are moved. They are renamed to
of_graph_get_next_endpoint, of_graph_get_remote_port, and
of_graph_get_remote_port_parent, respectively.
Since there are not that many current users yet, switch all of
them to the new functions right away.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Some devices do not produce timestamps that correspond to the end of the
frame. The user space should be informed on the matter. This patch achieves
that by adding buffer flags (and a mask) for timestamp sources since more
possible timestamping points are expected than just two.
A three-bit mask is defined (V4L2_BUF_FLAG_TSTAMP_SRC_MASK) and two of the
eight possible values is are defined V4L2_BUF_FLAG_TSTAMP_SRC_EOF for end of
frame (value zero) V4L2_BUF_FLAG_TSTAMP_SRC_SOE for start of exposure (next
value).
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Kamil Debski <k.debski@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The timestamp_type field used to contain only the timestamp type. Soon it
will be used for timestamp source flags as well. Rename the field
accordingly.
[m.chehab@samsung.com: do the change also to drivers/staging/media and at s2255]
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use own format ops for SDR data:
vidioc_enum_fmt_sdr_cap
vidioc_g_fmt_sdr_cap
vidioc_s_fmt_sdr_cap
vidioc_try_fmt_sdr_cap
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add new V4L device type VFL_TYPE_SDR for Software Defined Radio.
It is registered as /dev/swradio0 (/dev/sdr0 was already reserved).
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for 32-bit ioctls with v4l-subdev device nodes.
Rather than keep adding new ioctls to the list in v4l2-compat-ioctl32.c, just check
if the ioctl is a non-private V4L2 ioctl and if so, call the conversion code.
We keep forgetting to add new ioctls, so this is a more robust solution.
In addition extend the subdev API with support for a compat32 function to
convert custom v4l-subdev ioctls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are several left overs with my old email address.
Remove their occurrences and add myself at CREDITS, to
allow people to be able to reach me on my new addresses.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add and document a generic sysfs based scancode filtering interface for
making use of IR data matching hardware to filter out uninteresting
scancodes. Two filters exist, one for normal operation and one for
filtering scancodes which are permitted to wake the system from suspend.
The following files are added to /sys/class/rc/rc?/:
- filter: normal scancode filter value
- filter_mask: normal scancode filter mask
- wakeup_filter: wakeup scancode filter value
- wakeup_filter_mask: wakeup scancode filter mask
A new s_filter() driver callback is added which must arrange for the
specified filter to be applied at the right time. Drivers can convert
the scancode filter into a raw IR data filter, which can be applied
immediately or later (for wake up filters).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: linux-media@vger.kernel.org
Cc: Rob Landley <rob@landley.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This applies to HDMI-map register 0x69.
So far we have been using HPA manual mode.
This way we had control of HPA which could be
set after EDID had been programmed.
Using a Mac Mini with mini-displayport to DVI-D converter as source
caused the adv7842 to lock up and fail to detect any further signals.
After experimenting with different configurations it was found that
using the HPA auto mode and in addition letting RX-termination
be controlled by HPA prevented this error from occuring.
I was not able to re-create this problem on the adv7604.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
saa6588 always blocked while waiting for data, even if the filehandle
was in non-blocking mode.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If start_streaming returns -ENOBUFS, then it will be retried the next time
a buffer is queued. This means applications no longer need to know how many
buffers need to be queued before STREAMON can be called. This is particularly
useful for output stream I/O.
If a DMA engine needs at least X buffers before it can start streaming, then
for applications to get a buffer out as soon as possible they need to know
the minimum number of buffers to queue before STREAMON can be called. You can't
just try STREAMON after every buffer since on failure STREAMON will dequeue
all your buffers. (Is that a bug or a feature? Frankly, I'm not sure).
This patch simplifies applications substantially: they can just call STREAMON
at the beginning and then start queuing buffers and the DMA engine will
kick in automagically once enough buffers are available.
This also fixes using write() to stream video: the fileio implementation
calls streamon without having any queued buffers, which will fail today for
any driver that requires a minimum number of buffers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rather than taking the mmap semaphore at a relatively high-level function,
push it down to the place where it is really needed.
It was placed in vb2_queue_or_prepare_buf() to prevent racing with other
vb2 calls. The only way I can see that a race can happen is when two
threads queue the same buffer. The solution for that it to introduce
a PREPARING state.
Moving it down offers opportunities to simplify the code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a proper driver strength enum and use the same names in the platform
data as with adv7604.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The correct LLC DLL phase depends on the board layout, so this
should be part of the platform_data.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Tested-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The free-run mode can be board-specific.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
May also be wrong if the receiver is connected to more than one connector.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Both the PAL and NTSC standards are interlaced where a
frame consist of two fields. Total number of lines in a frame in both systems
are an odd number so the two fields will have different length.
In the 625 line standard ("PAL") the odd field of the frame is transmitted first,
while in the 525 standard ("NTSC") the even field is transmitted first.
This adds the possibility to change output config between the fields and standards.
This setting will reduce the "format-jitter" on the signal sent by the pixelport
moving the difference between the fields to vertical front/back-porch only.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Added support for YCrCb analog input.
If input is ADV7842_MODE_RGB and RGB quantization range is set to
V4L2_DV_RGB_RANGE_AUTO, then video with CEA timings will be received
as RGB. For ADV7842_MODE_COMP, automatic CSC mode will be selected.
See table 48 on page 281 in "ADV7842 Hardware Manual, Rev. 0, January 2011"
for details.
Make sure that when switching inputs the RGB quantization range is
updated as well.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
May also be wrong if the receiver is connected to more than one connector.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The driver strength is board dependent, so set it from the platform_data.
Signed-off-by: Mikhail Khelik <mkhelik@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The adv7604 supports four digital input ports. This patch adds support
for all of them, instead of just port A.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The omap24xx driver and the tcm825x sensor driver are the only two
remaining drivers to still use the old deprecated v4l2-int-device API.
Nobody maintains these drivers anymore. But unfortunately the v4l2-int-device
API is used by out-of-tree drivers (MXC platform). This is a very bad situation
since as long as this deprecated API stays in the kernel there is no reason for
those out-of-tree drivers to convert.
This patch moves v4l2-int-device and the two drivers that depend on it to
staging in preparation for their removal.
If someone would be interested in getting these drivers to work, then start with
this since it's not very far from the state where they used to work:
<URL:http://vihersipuli.retiisi.org.uk/cgi-bin/gitweb.cgi?p=~sailus/linux-omap/.git;a=summary>
The branch is n800-cam. Porting to up-to-date APIs can then be done. David
might have done some work in that area, so check with him first.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: David Cohen <dacohen@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
DIV_ROUND_UP() is defined in kernel.h which was not included by
media-entity.h. Do exactly that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In the ISI driver it reads the config register to get original value,
then set the correct FRATE_DIV and YCC_SWAP_MODE directly. This will
cause some bits overlap.
So we need to clear these bits first, then set correct value. This patch
fix it.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The supply list is needed by the platform driver, but not by the usb driver.
So this information belongs to the platform data and should not be hardcoded
in the subdevice driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Eduardo Valentin <edubezval@gmail.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The field isn't set when parsing the endpoint. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When CONFIG_OF is not defined the v4l2_of_parse_endpoint() function is
defined as a stub that returns -ENOSYS. Make the real function return an
integer as well to be able to differentiate between the two cases.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Guennadi Liakhovetski
Sakari Ailus
Hans Verkuil
Pablo Anton
Josh Wu
Mauro Carvalho Chehab
Ondrej Zary
Hans Verkuil
Sebastian Reichel
Boris BREZILLON
Prabhakar Lad
Martin Kaiser
nibble.max
Laurent Pinchart
Mauro Carvalho Chehab
Marcel J.E. Mol
Sonic Zhang
James Harper
David Härdeman
Michael Olbrich
Sakari Ailus
Ramakrishnan Muthukrishnan
Linus Torvalds
Lars-Peter Clausen
Arun Kumar K
Sylwester Nawrocki
Antti Palosaari
James Hogan
Daniel Jeong
Philipp Zabel
Martin Bugge
Mats Randgaard
Mikhail Khelik
Dinesh Ram