Pull i2c updates from Wolfram Sang:
"Mostly usual driver updates and improvements. The changelog should
give an idea. Standing out is the i2c-qup driver with lots of new
capabilities and we also have now an i2c-demuxer.
I'd especially like to welcome Peter Rosin as the i2c-mux maintainer.
He has an interesting series for muxes in the queue and agreed to look
after this part of the subsystem. Thank you, Peter, and welcome
again!
The octeon changes were applied pretty recently before the merge
window. I am aware. They are the first (and relatively simple)
patches of a larger overhaul to this driver. In case something goes
wrong with them, they are easy to fix (or revert). The advantage I
see is that they are out of the way, and I can concentrate on the next
block of patches. I really would like to apply the overhaul in
smaller batches to avoid regressions. And waiting a cycle for the
introductory patches seemed too much of a delay for me"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (39 commits)
i2c: octeon: Support I2C_M_RECV_LEN
i2c: octeon: Cleanup resource allocation code
i2c: octeon: Cleanup i2c-octeon driver
MAINTAINERS: add Peter Rosin as i2c mux maintainer
dt-bindings: i2c: Spelling s/propoerty/property/
i2c: immediately mark ourselves as registered
i2c: i801: sort IDs alphabetically
MAINTAINERS: Mika and me are designated reviewers for I2C DESIGNWARE
i2c: octeon: Cleanup kerneldoc comments
i2c: do not use internal data from driver core
i2c: cadence: Fix the kernel-doc warnings
i2c: imx: remove extra spaces.
i2c: rcar: don't open code of_device_get_match_data()
i2c: qup: Fix fifo handling after adding V2 support
i2c: xiic: Implement power management
i2c: piix4: Pre-shift the port number
i2c: piix4: Always use the same type for port
i2c: piix4: Support alternative port selection register
i2c: tegra: don't open code of_device_get_match_data()
i2c: riic, sh_mobile, rcar: Use ARCH_RENESAS
...
Pull f2fs updates from Jaegeuk Kim:
"New Features:
- uplift filesystem encryption into fs/crypto/
- give sysfs entries to control memroy consumption
Enhancements:
- aio performance by preallocating blocks in ->write_iter
- use writepages lock for only WB_SYNC_ALL
- avoid redundant inline_data conversion
- enhance forground GC
- use wait_for_stable_page as possible
- speed up SEEK_DATA and fiiemap
Bug Fixes:
- corner case in terms of -ENOSPC for inline_data
- hung task caused by long latency in shrinker
- corruption between atomic write and f2fs_trace_pid
- avoid garbage lengths in dentries
- revoke atomicly written pages if an error occurs
In addition, there are various minor bug fixes and clean-ups"
* tag 'for-f2fs-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (81 commits)
f2fs: submit node page write bios when really required
f2fs: add missing argument to f2fs_setxattr stub
f2fs: fix to avoid unneeded unlock_new_inode
f2fs: clean up opened code with f2fs_update_dentry
f2fs: declare static functions
f2fs: use cryptoapi crc32 functions
f2fs: modify the readahead method in ra_node_page()
f2fs crypto: sync ext4_lookup and ext4_file_open
fs crypto: move per-file encryption from f2fs tree to fs/crypto
f2fs: mutex can't be used by down_write_nest_lock()
f2fs: recovery missing dot dentries in root directory
f2fs: fix to avoid deadlock when merging inline data
f2fs: introduce f2fs_flush_merged_bios for cleanup
f2fs: introduce f2fs_update_data_blkaddr for cleanup
f2fs crypto: fix incorrect positioning for GCing encrypted data page
f2fs: fix incorrect upper bound when iterating inode mapping tree
f2fs: avoid hungtask problem caused by losing wake_up
f2fs: trace old block address for CoWed page
f2fs: try to flush inode after merging inline data
f2fs: show more info about superblock recovery
...
Highlights:
- Restructure Linux PTE on Book3S/64 to Radix format from Paul Mackerras
- Book3s 64 MMU cleanup in preparation for Radix MMU from Aneesh Kumar K.V
- Add POWER9 cputable entry from Michael Neuling
- FPU/Altivec/VSX save/restore optimisations from Cyril Bur
- Add support for new ftrace ABI on ppc64le from Torsten Duwe
Various cleanups & minor fixes from:
- Adam Buchbinder, Andrew Donnellan, Balbir Singh, Christophe Leroy, Cyril
Bur, Luis Henriques, Madhavan Srinivasan, Pan Xinhui, Russell Currey,
Sukadev Bhattiprolu, Suraj Jitindar Singh.
General:
- atomics: Allow architectures to define their own __atomic_op_* helpers from
Boqun Feng
- Implement atomic{, 64}_*_return_* variants and acquire/release/relaxed
variants for (cmp)xchg from Boqun Feng
- Add powernv_defconfig from Jeremy Kerr
- Fix BUG_ON() reporting in real mode from Balbir Singh
- Add xmon command to dump OPAL msglog from Andrew Donnellan
- Add xmon command to dump process/task similar to ps(1) from Douglas Miller
- Clean up memory hotplug failure paths from David Gibson
pci/eeh:
- Redesign SR-IOV on PowerNV to give absolute isolation between VFs from Wei
Yang.
- EEH Support for SRIOV VFs from Wei Yang and Gavin Shan.
- PCI/IOV: Rename and export virtfn_{add, remove} from Wei Yang
- PCI: Add pcibios_bus_add_device() weak function from Wei Yang
- MAINTAINERS: Update EEH details and maintainership from Russell Currey
cxl:
- Support added to the CXL driver for running on both bare-metal and
hypervisor systems, from Christophe Lombard and Frederic Barrat.
- Ignore probes for virtual afu pci devices from Vaibhav Jain
perf:
- Export Power8 generic and cache events to sysfs from Sukadev Bhattiprolu
- hv-24x7: Fix usage with chip events, display change in counter values,
display domain indices in sysfs, eliminate domain suffix in event names,
from Sukadev Bhattiprolu
Freescale:
- Updates from Scott: "Highlights include 8xx optimizations, 32-bit checksum
optimizations, 86xx consolidation, e5500/e6500 cpu hotplug, more fman and
other dt bits, and minor fixes/cleanup."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qkAt
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"This was delayed a day or two by some build-breakage on old toolchains
which we've now fixed.
There's two PCI commits both acked by Bjorn.
There's one commit to mm/hugepage.c which is (co)authored by Kirill.
Highlights:
- Restructure Linux PTE on Book3S/64 to Radix format from Paul
Mackerras
- Book3s 64 MMU cleanup in preparation for Radix MMU from Aneesh
Kumar K.V
- Add POWER9 cputable entry from Michael Neuling
- FPU/Altivec/VSX save/restore optimisations from Cyril Bur
- Add support for new ftrace ABI on ppc64le from Torsten Duwe
Various cleanups & minor fixes from:
- Adam Buchbinder, Andrew Donnellan, Balbir Singh, Christophe Leroy,
Cyril Bur, Luis Henriques, Madhavan Srinivasan, Pan Xinhui, Russell
Currey, Sukadev Bhattiprolu, Suraj Jitindar Singh.
General:
- atomics: Allow architectures to define their own __atomic_op_*
helpers from Boqun Feng
- Implement atomic{, 64}_*_return_* variants and acquire/release/
relaxed variants for (cmp)xchg from Boqun Feng
- Add powernv_defconfig from Jeremy Kerr
- Fix BUG_ON() reporting in real mode from Balbir Singh
- Add xmon command to dump OPAL msglog from Andrew Donnellan
- Add xmon command to dump process/task similar to ps(1) from Douglas
Miller
- Clean up memory hotplug failure paths from David Gibson
pci/eeh:
- Redesign SR-IOV on PowerNV to give absolute isolation between VFs
from Wei Yang.
- EEH Support for SRIOV VFs from Wei Yang and Gavin Shan.
- PCI/IOV: Rename and export virtfn_{add, remove} from Wei Yang
- PCI: Add pcibios_bus_add_device() weak function from Wei Yang
- MAINTAINERS: Update EEH details and maintainership from Russell
Currey
cxl:
- Support added to the CXL driver for running on both bare-metal and
hypervisor systems, from Christophe Lombard and Frederic Barrat.
- Ignore probes for virtual afu pci devices from Vaibhav Jain
perf:
- Export Power8 generic and cache events to sysfs from Sukadev
Bhattiprolu
- hv-24x7: Fix usage with chip events, display change in counter
values, display domain indices in sysfs, eliminate domain suffix in
event names, from Sukadev Bhattiprolu
Freescale:
- Updates from Scott: "Highlights include 8xx optimizations, 32-bit
checksum optimizations, 86xx consolidation, e5500/e6500 cpu
hotplug, more fman and other dt bits, and minor fixes/cleanup"
* tag 'powerpc-4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (179 commits)
powerpc: Fix unrecoverable SLB miss during restore_math()
powerpc/8xx: Fix do_mtspr_cpu6() build on older compilers
powerpc/rcpm: Fix build break when SMP=n
powerpc/book3e-64: Use hardcoded mttmr opcode
powerpc/fsl/dts: Add "jedec,spi-nor" flash compatible
powerpc/T104xRDB: add tdm riser card node to device tree
powerpc32: PAGE_EXEC required for inittext
powerpc/mpc85xx: Add pcsphy nodes to FManV3 device tree
powerpc/mpc85xx: Add MDIO bus muxing support to the board device tree(s)
powerpc/86xx: Introduce and use common dtsi
powerpc/86xx: Update device tree
powerpc/86xx: Move dts files to fsl directory
powerpc/86xx: Switch to kconfig fragments approach
powerpc/86xx: Update defconfigs
powerpc/86xx: Consolidate common platform code
powerpc32: Remove one insn in mulhdu
powerpc32: small optimisation in flush_icache_range()
powerpc: Simplify test in __dma_sync()
powerpc32: move xxxxx_dcache_range() functions inline
powerpc32: Remove clear_pages() and define clear_page() inline
...
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
Here is the big staging driver pull request for 4.6-rc1.
Lots of little things here, over 1600 patches or so. Notible is all of
the good Lustre work happening, those developers have finally woken up
and are cleaning up their code greatly. The Outreachy intern
application process is also happening, which brought in another 400 or
so patches. Full details are in the very long shortlog.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlbrc3EACgkQMUfUDdst+ylu5ACgpdTKjrZn2vHElW3GRhTpzJdQ
wz8AoJDeur2DmBkQrKD5/u/WL4UTRNZJ
=+Q6N
-----END PGP SIGNATURE-----
Merge tag 'staging-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here is the big staging driver pull request for 4.6-rc1.
Lots of little things here, over 1600 patches or so. Notable is all
of the good Lustre work happening, those developers have finally woken
up and are cleaning up their code greatly. The Outreachy intern
application process is also happening, which brought in another 400 or
so patches. Full details are in the very long shortlog.
All of these have been in linux-next with no reported issues"
* tag 'staging-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1673 commits)
staging: lustre: fix aligments in lnet selftest
staging: lustre: report minimum of two buffers for LNet selftest load test
staging: lustre: test for proper errno code in lstcon_rpc_trans_abort
staging: lustre: filter remaining extra spacing for lnet selftest
staging: lustre: remove extra spacing when setting variable for lnet selftest
staging: lustre: remove extra spacing of variable declartions for lnet selftest
staging: lustre: fix spacing issues checkpatch reported in lnet selftest
staging: lustre: remove returns in void function for lnet selftest
staging: lustre: fix bogus lst errors for lnet selftest
staging: netlogic: Replacing pr_err with dev_err after the call to devm_kzalloc
staging: mt29f_spinand: Replacing pr_info with dev_info after the call to devm_kzalloc
staging: android: ion: fix up file mode
staging: ion: debugfs invalid gfp mask
staging: rts5208: Replace pci_enable_device with pcim_enable_device
Staging: ieee80211: Place constant on right side of the test.
staging: speakup: Replace del_timer with del_timer_sync
staging: lowmemorykiller: fix 2 checks that checkpatch complained
staging: mt29f_spinand: Drop void pointer cast
staging: rdma: hfi1: file_ops: Replace ALIGN with PAGE_ALIGN
staging: rdma: hfi1: driver: Replace IS_ALIGNED with PAGE_ALIGNED
...
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model. We now finally make GPIO chips
devices. The gpio_chip will create a gpio_device which contains
a struct device, and this gpio_device struct is kept private.
Anything that needs to be kept private from the rest of the kernel
will gradually be moved over to the gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step
of a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices. We can now discover GPIOs properly from
userspace. We still have not come up with a way to actually *use*
GPIOs from userspace.
- To encourage people to use the character device for the future,
we have it always-enabled when using GPIO. The old sysfs ABI is
still opt-in (and can be used in parallel), but is marked as
deprecated. We will keep it around for the foreseeable future,
but it will not be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes. This dates back to when GPIO was an opt-in feature and
no shared library even existed: just a header file with proper
prototypes was provided and all semantics were up to the arch to
implement. These patches make the GPIO chip even more a proper
device and cleans out leftovers of the old in-kernel API here
and there. Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going
on, but we now return sane values in the vast majority of drivers
and the errorpath is sanitized. Some patches for powerpc, blackfin
and unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected
to SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9AJ4
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel v4.6. There is quite a
lot of interesting stuff going on.
The patches to other subsystems and arch-wide are ACKed as far as
possible, though I consider things like per-arch <asm/gpio.h> as
essentially a part of the GPIO subsystem so it should not be needed.
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model.
We now finally make GPIO chips devices. The gpio_chip will create
a gpio_device which contains a struct device, and this gpio_device
struct is kept private. Anything that needs to be kept private
from the rest of the kernel will gradually be moved over to the
gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step of
a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices.
We can now discover GPIOs properly from userspace. We still have
not come up with a way to actually *use* GPIOs from userspace.
- To encourage people to use the character device for the future, we
have it always-enabled when using GPIO. The old sysfs ABI is still
opt-in (and can be used in parallel), but is marked as deprecated.
We will keep it around for the foreseeable future, but it will not
be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes.
This dates back to when GPIO was an opt-in feature and no shared
library even existed: just a header file with proper prototypes was
provided and all semantics were up to the arch to implement. These
patches make the GPIO chip even more a proper device and cleans out
leftovers of the old in-kernel API here and there.
Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going on,
but we now return sane values in the vast majority of drivers and
the errorpath is sanitized. Some patches for powerpc, blackfin and
unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected to
SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller"
* tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (194 commits)
Revert "Share upstreaming patches"
gpio: mcp23s08: Fix clearing of interrupt.
gpiolib: Fix comment referring to gpio_*() in gpiod_*()
gpio: pca953x: Fix pca953x_gpio_set_multiple() on 64-bit
gpio: xgene: Fix kconfig for standby GIPO contoller
gpio: Add generic serializer DT binding
gpio: uapi: use 0xB4 as ioctl() major
gpio: tps65912: fix bad merge
Revert "gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free"
gpio: omap: drop dev field from gpio_bank structure
gpio: mpc8xxx: Slightly update the code for better readability
gpio: mpc8xxx: Remove *read_reg and *write_reg from struct mpc8xxx_gpio_chip
gpio: mpc8xxx: Fixup setting gpio direction output
gpio: mcp23s08: Add support for mcp23s18
dt-bindings: gpio: altera: Fix altr,interrupt-type property
gpio: add driver for MEN 16Z127 GPIO controller
gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free
gpio: timberdale: Switch to devm_ioremap_resource()
gpio: ts4800: Add IMX51 dependency
gpiolib: rewrite gpiodev_add_to_list
...
Here is the big char/misc driver update for 4.6-rc1.
The majority of the patches here is hwtracing and some new mic drivers,
but there's a lot of other driver updates as well. Full details in the
shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlbp9IcACgkQMUfUDdst+ykyJgCeLTC2QNGrh51kiJglkVJ0yD36
q4MAn0NkvSX2+iv5Jq8MaX6UQoRa4Nun
=MNjR
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big char/misc driver update for 4.6-rc1.
The majority of the patches here is hwtracing and some new mic
drivers, but there's a lot of other driver updates as well. Full
details in the shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'char-misc-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (238 commits)
goldfish: Fix build error of missing ioremap on UM
nvmem: mediatek: Fix later provider initialization
nvmem: imx-ocotp: Fix return value of imx_ocotp_read
nvmem: Fix dependencies for !HAS_IOMEM archs
char: genrtc: replace blacklist with whitelist
drivers/hwtracing: make coresight-etm-perf.c explicitly non-modular
drivers: char: mem: fix IS_ERROR_VALUE usage
char: xillybus: Fix internal data structure initialization
pch_phub: return -ENODATA if ROM can't be mapped
Drivers: hv: vmbus: Support kexec on ws2012 r2 and above
Drivers: hv: vmbus: Support handling messages on multiple CPUs
Drivers: hv: utils: Remove util transport handler from list if registration fails
Drivers: hv: util: Pass the channel information during the init call
Drivers: hv: vmbus: avoid unneeded compiler optimizations in vmbus_wait_for_unload()
Drivers: hv: vmbus: remove code duplication in message handling
Drivers: hv: vmbus: avoid wait_for_completion() on crash
Drivers: hv: vmbus: don't loose HVMSG_TIMER_EXPIRED messages
misc: at24: replace memory_accessor with nvmem_device_read
eeprom: 93xx46: extend driver to plug into the NVMEM framework
eeprom: at25: extend driver to plug into the NVMEM framework
...
Just a few patches this time around for the 4.6-rc1 merge window.
Largest is a new firmware driver, but there are some other updates to
the driver core in here as well, the shortlog has the details.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlbp9QoACgkQMUfUDdst+ynsOQCghpfAf3CJDr4PWGCKzDJzyQG9
rZYAn2VwKsqHzAxgLXZY5fQIjxSyaLek
=Mcvl
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Just a few patches this time around for the 4.6-rc1 merge window.
Largest is a new firmware driver, but there are some other updates to
the driver core in here as well, the shortlog has the details.
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
Revert "driver-core: platform: probe of-devices only using list of compatibles"
firmware: qemu config needs I/O ports
firmware: qemu_fw_cfg.c: fix typo FW_CFG_DATA_OFF
driver-core: platform: probe of-devices only using list of compatibles
driver-core: platform: fix typo in documentation for multi-driver helper
component: remove impossible condition
drivers: dma-coherent: simplify dma_init_coherent_memory return value
devicetree: update documentation for fw_cfg ARM bindings
firmware: create directory hierarchy for sysfs fw_cfg entries
firmware: introduce sysfs driver for QEMU's fw_cfg device
kobject: export kset_find_obj() for module use
driver core: bus: use to_subsys_private and to_device_private_bus
driver core: bus: use list_for_each_entry*
debugfs: Add stub function for debugfs_create_automount().
kernfs: make kernfs_walk_ns() use kernfs_pr_cont_buf[]
This is smallish update with minor changes to core and new driver and usual
updates. Nothing super exciting here..
- We have made slave address as physical to enable driver to do the mapping.
- We now expose the maxburst for slave dma as new capability so clients can
know this and program accordingly
- addition of device synchronize callbacks on omap and edma.
- pl330 updates to support DMAFLUSHP for Rockchip platforms.
- Updates and improved sg handling in Xilinx VDMA driver.
- New hidma qualcomm dma driver, though some bits are still in progress
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wCCJ
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.6-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This is smallish update with minor changes to core and new driver and
usual updates. Nothing super exciting here..
- We have made slave address as physical to enable driver to do the
mapping.
- We now expose the maxburst for slave dma as new capability so
clients can know this and program accordingly
- addition of device synchronize callbacks on omap and edma.
- pl330 updates to support DMAFLUSHP for Rockchip platforms.
- Updates and improved sg handling in Xilinx VDMA driver.
- New hidma qualcomm dma driver, though some bits are still in
progress"
* tag 'dmaengine-4.6-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (40 commits)
dmaengine: IOATDMA: revise channel reset workaround on CB3.3 platforms
dmaengine: add Qualcomm Technologies HIDMA channel driver
dmaengine: add Qualcomm Technologies HIDMA management driver
dmaengine: hidma: Add Device Tree binding
dmaengine: qcom_bam_dma: move to qcom directory
dmaengine: tegra: Move of_device_id table near to its user
dmaengine: xilinx_vdma: Remove unnecessary variable initializations
dmaengine: sirf: use __maybe_unused to hide pm functions
dmaengine: rcar-dmac: clear pertinence number of channels
dmaengine: sh: shdmac: don't open code of_device_get_match_data()
dmaengine: tegra: don't open code of_device_get_match_data()
dmaengine: qcom_bam_dma: Make driver work for BE
dmaengine: sun4i: support module autoloading
dma/mic_x100_dma: IS_ERR() vs PTR_ERR() typo
dmaengine: xilinx_vdma: Use readl_poll_timeout instead of do while loop's
dmaengine: xilinx_vdma: Simplify spin lock handling
dmaengine: xilinx_vdma: Fix issues with non-parking mode
dmaengine: xilinx_vdma: Improve SG engine handling
dmaengine: pl330: fix to support the burst mode
dmaengine: make slave address physical
...
Pull security layer updates from James Morris:
"There are a bunch of fixes to the TPM, IMA, and Keys code, with minor
fixes scattered across the subsystem.
IMA now requires signed policy, and that policy is also now measured
and appraised"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (67 commits)
X.509: Make algo identifiers text instead of enum
akcipher: Move the RSA DER encoding check to the crypto layer
crypto: Add hash param to pkcs1pad
sign-file: fix build with CMS support disabled
MAINTAINERS: update tpmdd urls
MODSIGN: linux/string.h should be #included to get memcpy()
certs: Fix misaligned data in extra certificate list
X.509: Handle midnight alternative notation in GeneralizedTime
X.509: Support leap seconds
Handle ISO 8601 leap seconds and encodings of midnight in mktime64()
X.509: Fix leap year handling again
PKCS#7: fix unitialized boolean 'want'
firmware: change kernel read fail to dev_dbg()
KEYS: Use the symbol value for list size, updated by scripts/insert-sys-cert
KEYS: Reserve an extra certificate symbol for inserting without recompiling
modsign: hide openssl output in silent builds
tpm_tis: fix build warning with tpm_tis_resume
ima: require signed IMA policy
ima: measure and appraise the IMA policy itself
ima: load policy using path
...
Hinawa [https://github.com/takaswie/libhinawa/] is a library for
access to IEEE 1394 devices. As a gobject introspection library, it
facilitates writing applications in high-level programming languages.
Besides generic I/O via /dev/fw* (firewire-cdev ABI), it also supports
control of IEEE 1394 audio hardware via ALSA hwdep ABIs which are
provided by sound/firewire drivers.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The Qualcomm Technologies HIDMA device has been designed to support
virtualization technology. The driver has been divided into two to follow
the hardware design.
1. HIDMA Management driver
2. HIDMA Channel driver
Each HIDMA HW consists of multiple channels. These channels share some set
of common parameters. These parameters are initialized by the management
driver during power up. Same management driver is used for monitoring the
execution of the channels. Management driver can change the performance
behavior dynamically such as bandwidth allocation and prioritization.
The management driver is executed in host context and is the main
management entity for all channels provided by the device.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Filter out a few adapter parameters which don't make sense in a guest.
Document the changes.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Switch attribute wakeup_data from binary to a text attribute.
This makes it easier to handle in userspace and allows to
use the output of tools like mode2 almost as is to set a
wakeup sequence.
Changing to a text format and values in microseconds also
makes the userspace interface independent of the setting of
SAMPLE_PERIOD in the driver.
In addition document the new sysfs attribute in
Documentation/ABI/testing/sysfs-class-rc-nuvoton.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Good to see several new contributors in this set - and more generally a
number of new 'faces' over this whole cycle.
Staging movements
* hmc5843
- out of staging.
* periodic RTC trigger
- driver dropped. This is an ancient driver (brings back some memories ;)
that was always somewhat of a bodge. Originally there was a driver that
never went into mainline that supported large numbers of periodict timers
on the PXA270 via this route. Discussions to have a generic periodic
timer subsystem never went anywhere. At the time RTC periodic
interrupts were real - now they are emulated using high resolution
timers so with the HRT driver this has become pointless.
New device support
* mpu6050 driver
- Add support for the mpu6500.
* TI tpl0102 potentiometer
- new driver.
* Vybrid SoC DAC
- new driver. The ADC on this SoC has been supported for a while, this
adds a separate driver for the DAC.
New Features
* hmc5844
- Attributes to configure the bias current (typically part of a self test)
This could be done before via a somewhat obscure custom interface.
This at least makes it easy to tell what is going on.
- Document all custom attributes.
* mpu6050
- Add support for calibration offset control and readback.
* ms5611
- power regulator support. This is always one that gets added the
first time someone has a board that needs it. Here it was needed,
hence it was added.
Cleanups / minor fixes
* tree wide
- clean up all the myriad different return values in response to a
failure of i2c_check_functionality. After discussions everyone seemed
happy wiht -EOPNOTSUPP which seems to describe the situation well.
I encouraged a tree wide cleanup to set a good example in future for
this.
* core
- Typos in the iio_event_spec documentation in iio.h
* afe4403
- select REGMAP_SPI to avoid dependency issues
- mark suspend/resume as __maybe_unused to avoid warnings
* afe4404
- mark suspend/resume as __maybe_unused to avoid warnings
* atlas-ph-sensor
- switch the regmap cache type from linear to rbtree to gain reading of
registers on initial startup. It's not immediately obvious, but
regmap flat is meant for high performances cases so doesn't read these
registers.
- use regmap_bulk_read in one case where it was using
i2c_smbus_read_i2c_block_data directly (unlike everything else that was
through regmap).
* ina2xx
- stype cleanups (lots of them!)
* isl29018
- Get the struct device back from regmap rather than storing another
copy of it in the private data. This cleanup makes sense in a number
of other drivers so patches may well follow.
* mpu6050
- style cleanups (lots of them!)
- improved return value handling
- use usleep_range to avoid the usual issues with very short msleeps.
- add some missing documentation.
* ms5611
- use the probed device name for the device rather than the driver name.
- select IIO_BUFFER to avoid dependency issues
* palmas
- drop IRQF_EARLY_RESUME as no longer needed after genirq changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=rDIQ
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.6c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third set of IIO new device support, features and cleanups for the 4.6 cycle.
Good to see several new contributors in this set - and more generally a
number of new 'faces' over this whole cycle.
Staging movements
* hmc5843
- out of staging.
* periodic RTC trigger
- driver dropped. This is an ancient driver (brings back some memories ;)
that was always somewhat of a bodge. Originally there was a driver that
never went into mainline that supported large numbers of periodict timers
on the PXA270 via this route. Discussions to have a generic periodic
timer subsystem never went anywhere. At the time RTC periodic
interrupts were real - now they are emulated using high resolution
timers so with the HRT driver this has become pointless.
New device support
* mpu6050 driver
- Add support for the mpu6500.
* TI tpl0102 potentiometer
- new driver.
* Vybrid SoC DAC
- new driver. The ADC on this SoC has been supported for a while, this
adds a separate driver for the DAC.
New Features
* hmc5844
- Attributes to configure the bias current (typically part of a self test)
This could be done before via a somewhat obscure custom interface.
This at least makes it easy to tell what is going on.
- Document all custom attributes.
* mpu6050
- Add support for calibration offset control and readback.
* ms5611
- power regulator support. This is always one that gets added the
first time someone has a board that needs it. Here it was needed,
hence it was added.
Cleanups / minor fixes
* tree wide
- clean up all the myriad different return values in response to a
failure of i2c_check_functionality. After discussions everyone seemed
happy wiht -EOPNOTSUPP which seems to describe the situation well.
I encouraged a tree wide cleanup to set a good example in future for
this.
* core
- Typos in the iio_event_spec documentation in iio.h
* afe4403
- select REGMAP_SPI to avoid dependency issues
- mark suspend/resume as __maybe_unused to avoid warnings
* afe4404
- mark suspend/resume as __maybe_unused to avoid warnings
* atlas-ph-sensor
- switch the regmap cache type from linear to rbtree to gain reading of
registers on initial startup. It's not immediately obvious, but
regmap flat is meant for high performances cases so doesn't read these
registers.
- use regmap_bulk_read in one case where it was using
i2c_smbus_read_i2c_block_data directly (unlike everything else that was
through regmap).
* ina2xx
- stype cleanups (lots of them!)
* isl29018
- Get the struct device back from regmap rather than storing another
copy of it in the private data. This cleanup makes sense in a number
of other drivers so patches may well follow.
* mpu6050
- style cleanups (lots of them!)
- improved return value handling
- use usleep_range to avoid the usual issues with very short msleeps.
- add some missing documentation.
* ms5611
- use the probed device name for the device rather than the driver name.
- select IIO_BUFFER to avoid dependency issues
* palmas
- drop IRQF_EARLY_RESUME as no longer needed after genirq changes.
B.A.T.M.A.N. V. Its implementation started quite some years ago,
but due to the big changes being introduced it took a while to be
discussed, designed, worked, re-worked, tested and debugged (well,
we're never done with the latest). The entire operation has
basically been a team work involving all the core contributors
together with other people interested in the project.
The new protocol is divided into two main subcomponents, called
respectively ELP and OGMv2. The former is in charge of
dealing with the neighbour discovery and link quality estimation,
while the latter implements the algorithm that spreads the
metrics around the network and computes optimal paths.
The biggest change introduced with B.A.T.M.A.N. V is the new
metric: the protocol won't rely on packet loss anymore, but it
will use the estimated throughput extracted directly from the
wifi driver (when available) by querying cfg80211.
Batman-adv will also send some unicast probing packets when
an interface is not used for payload traffic to make sure that
such values are current.
The new protocol can be compiled-in or not like other
features we have and when selected will pull in CFG80211 as
dependency for the reason described above.
Thanks to the big work brought up in the past by Marek Lindner,
batman-adv can easily deal several protocol implementations,
therefore compiling in this new version does not exclude the
older.
This means that the user is offered the option to choose
the protocol when creating the mesh interface (default is the
old one to keep backward compatibility).
Along with the protocol there are some sysfs knobs that are
introduced to fine tune some of its behaviours, but users
are recommended to keep the default values unless they know
what they are doing.
The last patch is about advertising our own patchwork platform
(thanks to Sven Eckelmann for having set that up!) in the
MAINTAINERS file.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=qd6p
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
batman-adv 20160229
this is our (hopefully) latest batch of patches intended for net-next.
With this patchset we finally introduce B.A.T.M.A.N. V: the latest
version of our routing protocol.
Technical documentation describing the protocol in more detail can
be found in our wiki[1][2][3][4].
For what concerns this pull request, you can find the high level
description right below.
[1] https://www.open-mesh.org/projects/batman-adv/wiki/BATMAN_V
[2] https://www.open-mesh.org/projects/batman-adv/wiki/OGMv2
[3] https://www.open-mesh.org/projects/batman-adv/wiki/ELP
[4] https://www.open-mesh.org/projects/batman-adv/wiki/BATMAN_V_Tests
...
With this patchset we finally introduce our new routing protocol:
B.A.T.M.A.N. V. Its implementation started quite some years ago,
but due to the big changes being introduced it took a while to be
discussed, designed, worked, re-worked, tested and debugged (well,
we're never done with the latest). The entire operation has
basically been a team work involving all the core contributors
together with other people interested in the project.
The new protocol is divided into two main subcomponents, called
respectively ELP and OGMv2. The former is in charge of
dealing with the neighbour discovery and link quality estimation,
while the latter implements the algorithm that spreads the
metrics around the network and computes optimal paths.
The biggest change introduced with B.A.T.M.A.N. V is the new
metric: the protocol won't rely on packet loss anymore, but it
will use the estimated throughput extracted directly from the
wifi driver (when available) by querying cfg80211.
Batman-adv will also send some unicast probing packets when
an interface is not used for payload traffic to make sure that
such values are current.
The new protocol can be compiled-in or not like other
features we have and when selected will pull in CFG80211 as
dependency for the reason described above.
Thanks to the big work brought up in the past by Marek Lindner,
batman-adv can easily deal several protocol implementations,
therefore compiling in this new version does not exclude the
older.
This means that the user is offered the option to choose
the protocol when creating the mesh interface (default is the
old one to keep backward compatibility).
Along with the protocol there are some sysfs knobs that are
introduced to fine tune some of its behaviours, but users
are recommended to keep the default values unless they know
what they are doing.
The last patch is about advertising our own patchwork platform
(thanks to Sven Eckelmann for having set that up!) in the
MAINTAINERS file.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This attribute is exported to user space to disable the link
throughput auto-detection by setting a fixed value.
The throughput override value is used when batman-adv is
computing the link throughput towards a neighbour.
If the value is set to 0 then batman-adv will try to detect
the throughput by itself.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
This parameter can be set individually on each interface and
allows the configuration of the elp interval for the link
quality measurements during runtime. Usually it is desirable
to set it to a higher (= slower) value on interfaces which
have a more static characteristic (e.g. wired interfaces)
or very dense neighbourhoods to reduce overhead.
Developed by Linus during a 6 months trainee study period in
Ascom (Switzerland) AG.
Signed-off-by: Linus Luessing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
[antonio@open-mesh.com: respin on top of the latest master]
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Add driver support for DAC peripheral on Vybrid SoC.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There is still quite a bit of code using this interface, so we can't
just remove it. Hopefully it will be possible in the future, but since
its scheduled removal date is past 2 years already, we are better having
the documentation reflecting the current state of things.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The "claim" sysfs interface has been removed, so its documentation now
lives in the "removed" folder.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This was scheduled to be removed in 2012 by:
commit 69c86373c6
Author: florian@mickler.org <florian@mickler.org>
Date: Wed Feb 24 12:05:16 2010 +0100
Document the rfkill sysfs ABI
This moves sysfs ABI info from Documentation/rfkill.txt to the
ABI subfolder and reformats it.
This also schedules the deprecated sysfs parts to be removed in
2012 (claim file) and 2014 (state file).
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch introduces lifetime IO write statistics exposed to the sysfs interface.
The write IO amount is obtained from block layer, accumulated in the file system and
stored in the hot node summary of checkpoint.
Signed-off-by: Shuoran Liu <liushuoran@huawei.com>
Signed-off-by: Pengyang Hou <houpengyang@huawei.com>
[Jaegeuk Kim: add sysfs documentation]
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch exports a new sysfs entry 'dirty_nat_ratio' to control threshold
of dirty nat entries, if current ratio exceeds configured threshold,
checkpoint will be triggered in f2fs_balance_fs_bg for flushing dirty nats.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This resolves the merge issues and confusions people were having with
the goldfish drivers due to changes for them showing up in two different
trees.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ABI file documenting hmc5843 non-standard attributes
meas_conf and meas_conf_available for bias current
configuration.
Signed-off-by: Cristina Moraru <cristina.moraru09@gmail.com>
Cc: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add IMA policy support for measuring/appraising the kexec image and
initramfs. Two new IMA policy identifiers KEXEC_KERNEL_CHECK and
KEXEC_INITRAMFS_CHECK are defined.
Example policy rules:
measure func=KEXEC_KERNEL_CHECK
appraise func=KEXEC_KERNEL_CHECK appraise_type=imasig
measure func=KEXEC_INITRAMFS_CHECK
appraise func=KEXEC_INITRAMFS_CHECK appraise_type=imasig
Moving the enumeration to the vfs layer simplified the patches, allowing
the IMA changes, for the most part, to be separated from the other
changes. Unfortunately, passing either a kernel_read_file_id or a
ima_hooks enumeration within IMA is messy.
Option 1: duplicate kernel_read_file enumeration in ima_hooks
enum kernel_read_file_id {
...
READING_KEXEC_IMAGE,
READING_KEXEC_INITRAMFS,
READING_MAX_ID
enum ima_hooks {
...
KEXEC_KERNEL_CHECK
KEXEC_INITRAMFS_CHECK
Option 2: define ima_hooks as extension of kernel_read_file
eg: enum ima_hooks {
FILE_CHECK = READING_MAX_ID,
MMAP_CHECK,
In order to pass both kernel_read_file_id and ima_hooks values, we
would need to specify a struct containing a union.
struct caller_id {
union {
enum ima_hooks func_id;
enum kernel_read_file_id read_id;
};
};
Option 3: incorportate the ima_hooks enumeration into kernel_read_file_id,
perhaps changing the enumeration name.
For now, duplicate the new READING_KEXEC_IMAGE/INITRAMFS in the ima_hooks.
Changelog v4:
- replaced switch statement with a kernel_read_file_id to an ima_hooks
id mapping array - Dmitry
- renamed ima_hook tokens KEXEC_CHECK and INITRAMFS_CHECK to
KEXEC_KERNEL_CHECK and KEXEC_INITRAMFS_CHECK respectively - Dave Young
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Acked-by: Petko Manolov <petkan@mip-labs.com>
Acked-by: Dmitry Kasatkin <dmitry.kasatkin@huawei.com>
Cc: Dave Young <dyoung@redhat.com>
This driver allows an I2C bus to switch between multiple masters. This
is not hot-switching because connected I2C slaves will be
re-instantiated. It is meant to select the best I2C core at runtime once
the task is known. Example: Prefer i2c-gpio over another I2C core
because of HW errata affecting your use case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Each fw_cfg entry of type "file" has an associated 56-char,
nul-terminated ASCII string which represents its name. While
the fw_cfg device doesn't itself impose any specific naming
convention, QEMU developers have traditionally used path name
semantics (i.e. "etc/acpi/rsdp") to descriptively name the
various fw_cfg "blobs" passed into the guest.
This patch attempts, on a best effort basis, to create a
directory hierarchy representing the content of fw_cfg file
names, under /sys/firmware/qemu_fw_cfg/by_name.
Upon successful creation of all directories representing the
"dirname" portion of a fw_cfg file, a symlink will be created
to represent the "basename", pointing at the appropriate
/sys/firmware/qemu_fw_cfg/by_key entry. If a file name is not
suitable for this procedure (e.g., if its basename or dirname
components collide with an already existing dirname component
or basename, respectively) the corresponding fw_cfg blob is
skipped and will remain available in sysfs only by its selector
key value.
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make fw_cfg entries of type "file" available via sysfs. Entries
are listed under /sys/firmware/qemu_fw_cfg/by_key, in folders
named after each entry's selector key. Filename, selector value,
and size read-only attributes are included for each entry. Also,
a "raw" attribute allows retrieval of the full binary content of
each entry.
The fw_cfg device can be instantiated automatically from ACPI or
the Device Tree, or manually by using a kernel module (or command
line) parameter, with a syntax outlined in the documentation file.
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This marks the (optional) sysfs GPIO ABI as obsolete and schedules
it for removal in 2020.
Cc: Johan Hovold <johan@kernel.org>
Cc: Michael Welling <mwelling@ieee.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Put in some documentation for the new character device ABI
so we can properly etch it in stone.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Linear Technology LTC2606, LTC2607, LTC2609, LTC2616, LTC2617,
LTC2619, LTC2626, LTC2627 and LTC2629 devices are very similar
to the AD5064 device.
This patch adds support for those devices.
Datasheet for LTC devices:
LTC2606, LTC2616, LTC2626: http://www.linear.com/docs/6398
LTC2607, LTC2617, LTC2627: http://www.linear.com/docs/8977
LTC2709, LTC2619, LTC2629: http://www.linear.com/docs/8477
Signed-off-by: Marc Andre <marc.andre@netline.ch>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add vendor and device attributes to VMBUS devices. These will be used
by Hyper-V tools as well user-level RDMA libraries that will use the
vendor/device tuple to discover the RDMA device.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add driver for the TI AFE4404 heart rate monitor and pulse oximeter.
This device detects reflected LED light fluctuations and presents an ADC
value to the user space for further signal processing.
Datasheet: http://www.ti.com/product/AFE4404/datasheet
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Device Support
* ad5761
- new driver
* at91_sama5d2 ADC.
- new driver and MAINTAINERS entry.
- minor cleanups followed.
* atlas pH-SM
- new driver (this has possibly the prettiest data sheet I've ever seen)
* mcp3422
- mcp3425 ADC added.
* mcp4725
- mcp4726 DAC added.
* mma8452
- mma8451q accelerometer added.
* mpl115
- mpl115a1 added (a lot bigger than it seems as this is an SPI part whereas
previous parts were i2c).
* si7005
- Hoperf th02 (seems to be a repackaged part)
* si7020
- Hoperf th06 (seems to be a repackaged part)
New features
* Core
- IIO_PH type. Does what it says on the tin.
* max30100
- LED current configuration support.
* mcp320x
- more differential measurement combinations.
* mma8452
- free fall deteciton
- opt3001
- enable operation without a IRQ line.
- device tree docs. Somehow the original docs have disappeared down
a rabbit hole, so here is a new set.
* st-sensors
- Support active-low interrupts.
Cleanups and minor / not so minor reworks
* Documentation
- drop some defunct ABI from the docs in staging.
* presure / Kconfig
- white space cleanup.
* ad7150
- BIT macro usage
- Alignment fixes
* ad7192
- false indent fixed.
* ak8975
- constify the ak_def structures
* axp288
- drop a redundant double const.
* dht11
- substantial reliability improvements by being more tolerant
of missing start bits.
- simplify the decoding algorithm
* mma8452
- whitespace cleanup
* mpl115
- don't bother setting i2c_client_data as nothing uses it.
* mpu6050
- drop unused function parameter.
* opt3001
- extract integration time as constants.
- trivial refactoring.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=fgTH
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new IIO device support, features and cleanups for the 4.6 cycle.
Device Support
* ad5761
- new driver
* at91_sama5d2 ADC.
- new driver and MAINTAINERS entry.
- minor cleanups followed.
* atlas pH-SM
- new driver (this has possibly the prettiest data sheet I've ever seen)
* mcp3422
- mcp3425 ADC added.
* mcp4725
- mcp4726 DAC added.
* mma8452
- mma8451q accelerometer added.
* mpl115
- mpl115a1 added (a lot bigger than it seems as this is an SPI part whereas
previous parts were i2c).
* si7005
- Hoperf th02 (seems to be a repackaged part)
* si7020
- Hoperf th06 (seems to be a repackaged part)
New features
* Core
- IIO_PH type. Does what it says on the tin.
* max30100
- LED current configuration support.
* mcp320x
- more differential measurement combinations.
* mma8452
- free fall deteciton
- opt3001
- enable operation without a IRQ line.
- device tree docs. Somehow the original docs have disappeared down
a rabbit hole, so here is a new set.
* st-sensors
- Support active-low interrupts.
Cleanups and minor / not so minor reworks
* Documentation
- drop some defunct ABI from the docs in staging.
* presure / Kconfig
- white space cleanup.
* ad7150
- BIT macro usage
- Alignment fixes
* ad7192
- false indent fixed.
* ak8975
- constify the ak_def structures
* axp288
- drop a redundant double const.
* dht11
- substantial reliability improvements by being more tolerant
of missing start bits.
- simplify the decoding algorithm
* mma8452
- whitespace cleanup
* mpl115
- don't bother setting i2c_client_data as nothing uses it.
* mpu6050
- drop unused function parameter.
* opt3001
- extract integration time as constants.
- trivial refactoring.
- Remove usage of ib_query_device and instead store attributes in
ib_device struct
- Move iopoll out of block and into lib, rename to irqpoll, and use
in several places in the rdma stack as our new completion queue
polling library mechanism. Update the other block drivers that
already used iopoll to use the new mechanism too.
- Replace the per-entry GID table locks with a single GID table lock
- IPoIB multicast cleanup
- Cleanups to the IB MR facility
- Add support for 64bit extended IB counters
- Fix for netlink oops while parsing RDMA nl messages
- RoCEv2 support for the core IB code
- mlx4 RoCEv2 support
- mlx5 RoCEv2 support
- Cross Channel support for mlx5
- Timestamp support for mlx5
- Atomic support for mlx5
- Raw QP support for mlx5
- MAINTAINERS update for mlx4/mlx5
- Misc ocrdma, qib, nes, usNIC, cxgb3, cxgb4, mlx4, mlx5 updates
- Add support for remote invalidate to the iSER driver (pushed through the
RDMA tree due to dependencies, acknowledged by nab)
- Update to NFSoRDMA (pushed through the RDMA tree due to dependencies,
acknowledged by Bruce)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5oO7
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"Initial roundup of 4.5 merge window patches
- Remove usage of ib_query_device and instead store attributes in
ib_device struct
- Move iopoll out of block and into lib, rename to irqpoll, and use
in several places in the rdma stack as our new completion queue
polling library mechanism. Update the other block drivers that
already used iopoll to use the new mechanism too.
- Replace the per-entry GID table locks with a single GID table lock
- IPoIB multicast cleanup
- Cleanups to the IB MR facility
- Add support for 64bit extended IB counters
- Fix for netlink oops while parsing RDMA nl messages
- RoCEv2 support for the core IB code
- mlx4 RoCEv2 support
- mlx5 RoCEv2 support
- Cross Channel support for mlx5
- Timestamp support for mlx5
- Atomic support for mlx5
- Raw QP support for mlx5
- MAINTAINERS update for mlx4/mlx5
- Misc ocrdma, qib, nes, usNIC, cxgb3, cxgb4, mlx4, mlx5 updates
- Add support for remote invalidate to the iSER driver (pushed
through the RDMA tree due to dependencies, acknowledged by nab)
- Update to NFSoRDMA (pushed through the RDMA tree due to
dependencies, acknowledged by Bruce)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (169 commits)
IB/mlx5: Unify CQ create flags check
IB/mlx5: Expose Raw Packet QP to user space consumers
{IB, net}/mlx5: Move the modify QP operation table to mlx5_ib
IB/mlx5: Support setting Ethernet priority for Raw Packet QPs
IB/mlx5: Add Raw Packet QP query functionality
IB/mlx5: Add create and destroy functionality for Raw Packet QP
IB/mlx5: Refactor mlx5_ib_qp to accommodate other QP types
IB/mlx5: Allocate a Transport Domain for each ucontext
net/mlx5_core: Warn on unsupported events of QP/RQ/SQ
net/mlx5_core: Add RQ and SQ event handling
net/mlx5_core: Export transport objects
IB/mlx5: Expose CQE version to user-space
IB/mlx5: Add CQE version 1 support to user QPs and SRQs
IB/mlx5: Fix data validation in mlx5_ib_alloc_ucontext
IB/sa: Fix netlink local service GFP crash
IB/srpt: Remove redundant wc array
IB/qib: Improve ipoib UD performance
IB/mlx4: Advertise RoCE v2 support
IB/mlx4: Create and use another QP1 for RoCEv2
IB/mlx4: Enable send of RoCE QP1 packets with IP/UDP headers
...
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Introduce configfs support for unlocked configfs_depend_item()
(krzysztof + andrezej)
- Conversion of usb-gadget target driver to new function registration
interface (andrzej + sebastian)
- Enable qla2xxx FC target mode support for Extended Logins (himansu +
giridhar)
- Enable qla2xxx FC target mode support for Exchange Offload (himansu +
giridhar)
- Add qla2xxx FC target mode irq affinity notification + selective
command queuing. (quinn + himanshu)
- Fix iscsi-target deadlock in se_node_acl configfs deletion (sagi +
nab)
- Convert se_node_acl configfs deletion + se_node_acl->queue_depth to
proper se_session->sess_kref + target_get_session() usage. (hch +
sagi + nab)
- Fix long-standing race between se_node_acl->acl_kref get and
get_initiator_node_acl() lookup. (hch + nab)
- Fix target/user block-size handling, and make sure netlink reaches
all network namespaces (sheng + andy)
Note there is an outstanding bug-fix series for remote I_T nexus port
TMR LUN_RESET has been posted and still being tested, and will likely
become post -rc1 material at this point"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (56 commits)
scsi: qla2xxxx: avoid type mismatch in comparison
target/user: Make sure netlink would reach all network namespaces
target: Obtain se_node_acl->acl_kref during get_initiator_node_acl
target: Convert ACL change queue_depth se_session reference usage
iscsi-target: Fix potential dead-lock during node acl delete
ib_srpt: Convert acl lookup to modern get_initiator_node_acl usage
tcm_fc: Convert acl lookup to modern get_initiator_node_acl usage
tcm_fc: Wait for command completion before freeing a session
target: Fix a memory leak in target_dev_lba_map_store()
target: Support aborting tasks with a 64-bit tag
usb/gadget: Remove set-but-not-used variables
target: Remove an unused variable
target: Fix indentation in target_core_configfs.c
target/user: Allow user to set block size before enabling device
iser-target: Fix non negative ERR_PTR isert_device_get usage
target/fcoe: Add tag support to tcm_fc
qla2xxx: Check for online flag instead of active reset when transmitting responses
qla2xxx: Set all queues to 4k
qla2xxx: Disable ZIO at start time.
qla2xxx: Move atioq to a different lock to reduce lock contention
...
Pull watchdog updates from Wim Van Sebroeck:
"This adds following items:
- watchdog restart handler support
- watchdog reboot notifier support
- watchdog sysfs attributes
- support for the following new devices: AMD Mullins platform, AMD
Carrizo platform, meson8b SoC, CSRatlas7, TS-4800, Alphascale
asm9260-wdt, Zodiac, Sigma Designs SMP86xx/SMP87xx
- Changes in refcounting for the watchdog core
- watchdog core improvements
- and small fixes"
* git://www.linux-watchdog.org/linux-watchdog: (60 commits)
watchdog: asm9260: remove __init and __exit annotations
watchdog: Drop pointer to watchdog device from struct watchdog_device
watchdog: ziirave: Use watchdog infrastructure to create sysfs attributes
watchdog: Add support for creating driver specific sysfs attributes
watchdog: kill unref/ref ops
watchdog: stmp3xxx: Remove unused variables
watchdog: add MT7621 watchdog support
hwmon: (sch56xx) Drop watchdog driver data reference count callbacks
watchdog: da9055_wdt: Drop reference counting
watchdog: da9052_wdt: Drop reference counting
watchdog: Separate and maintain variables based on variable lifetime
watchdog: diag288: Stop re-using watchdog core internal flags
watchdog: Create watchdog device in watchdog_dev.c
watchdog: qcom-wdt: Do not set 'dev' in struct watchdog_device
watchdog: mena21: Do not use device pointer from struct watchdog_device
watchdog: gpio: Do not use device pointer from struct watchdog_device
watchdog: tangox: Print info message using pointer to platform device
watchdog: bcm2835_wdt: Drop log message if watchdog is stopped
devicetree: watchdog: add binding for Sigma Designs SMP8642 watchdog
watchdog: add support for Sigma Designs SMP86xx/SMP87xx
...
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
floppy: make local variable non-static
exynos: fixes an incorrect header guard
dt-bindings: fixes some incorrect header guards
cpufreq-dt: correct dead link in documentation
cpufreq: ARM big LITTLE: correct dead link in documentation
treewide: Fix typos in printk
Documentation: filesystem: Fix typo in fs/eventfd.c
fs/super.c: use && instead of & for warn_on condition
Documentation: fix sysfs-ptp
lib: scatterlist: fix Kconfig description
Pull livepatching updates from Jiri Kosina:
- RO/NX attribute fixes for patch module relocations from Josh
Poimboeuf. As part of this effort, module.c has been cleaned up as
well and livepatching is piggy-backing on this cleanup. Rusty is OK
with this whole lot going through livepatching tree.
- symbol disambiguation support from Chris J Arges. That series is
also
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
but this came in only after I've alredy pushed out. Didn't want to
rebase because of that, hence I am mentioning it here.
- symbol lookup fix from Miroslav Benes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
livepatch: Cleanup module page permission changes
module: keep percpu symbols in module's symtab
module: clean up RO/NX handling.
module: use a structure to encapsulate layout.
gcov: use within_module() helper.
module: Use the same logic for setting and unsetting RO/NX
livepatch: function,sympos scheme in livepatch sysfs directory
livepatch: add sympos as disambiguator field to klp_reloc
livepatch: add old_sympos as disambiguator field to klp_func
Pull f2fs updates from Jaegeuk Kim:
"This series adds two ioctls to control cached data and fragmented
files. Most of the rest fixes missing error cases and bugs that we
have not covered so far. Summary:
Enhancements:
- support an ioctl to execute online file defragmentation
- support an ioctl to flush cached data
- speed up shrinking of extent_cache entries
- handle broken superblock
- refector dirty inode management infra
- revisit f2fs_map_blocks to handle more cases
- reduce global lock coverage
- add detecting user's idle time
Major bug fixes:
- fix data race condition on cached nat entries
- fix error cases of volatile and atomic writes"
* tag 'for-f2fs-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (87 commits)
f2fs: should unset atomic flag after successful commit
f2fs: fix wrong memory condition check
f2fs: monitor the number of background checkpoint
f2fs: detect idle time depending on user behavior
f2fs: introduce time and interval facility
f2fs: skip releasing nodes in chindless extent tree
f2fs: use atomic type for node count in extent tree
f2fs: recognize encrypted data in f2fs_fiemap
f2fs: clean up f2fs_balance_fs
f2fs: remove redundant calls
f2fs: avoid unnecessary f2fs_balance_fs calls
f2fs: check the page status filled from disk
f2fs: introduce __get_node_page to reuse common code
f2fs: check node id earily when readaheading node page
f2fs: read isize while holding i_mutex in fiemap
Revert "f2fs: check the node block address of newly allocated nid"
f2fs: cover more area with nat_tree_lock
f2fs: introduce max_file_blocks in sbi
f2fs crypto: check CONFIG_F2FS_FS_XATTR for encrypted symlink
f2fs: introduce zombie list for fast shrinking extent trees
...
Here is the big staging driver pull request for 4.5-rc1. Lots of
cleanups and fixes here, not as many as some releases, but 800+ isn't
that bad. Full details in the shortlog. All of these have been in
linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlaV0VgACgkQMUfUDdst+ykvAwCeIN/Ot3OuWD/d1RQrcUzh028H
rlUAn3YOHCFlQhAnUI+9KMNjH0CwAJKp
=Oij1
-----END PGP SIGNATURE-----
Merge tag 'staging-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here is the big staging driver pull request for 4.5-rc1.
Lots of cleanups and fixes here, not as many as some releases, but
800+ isn't that bad. Full details in the shortlog. All of these have
been in linux-next for a while"
* tag 'staging-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (843 commits)
Revert "arm64: dts: Add dts files to enable ION on Hi6220 SoC."
staging: gdm724x: constify tty_port_operations structs
staging: gdm72xx: add userspace data struct
staging: gdm72xx: Replace timeval with ktime_t
iio: adc: ina2xx: Fix incorrect report of data endianness to userspace.
iio: light: us5182d: Refactor read_raw function
iio: light: us5182d: Add interrupt support and events
iio: light: us5182d: Fix enable status inconcistency
iio: Make IIO value formating function globally available.
staging: emxx_udc: use list_first_entry_or_null()
staging/emxx_udc: fix 64-bit warnings
STAGING: COMEDI: Using kernel types in plx9080.h
STAGING: COMEDI: Added spaces around binary operators in plx9080.h
STAGING: COMEDI: Fixed format of comments in plx9080.h
staging: comedi: comedilib.h: Coding style warning fix for block comments
staging: comedi: s526: add macros for counter control reg values
staging: comedi: s526: replace counter mode bitfield struct
staging: comedi: check for more errors for zero-length write
staging: comedi: simplify returned errors for comedi_write()
staging: comedi: return error on "write" if no command set up
...
Here is the big USB drivers update for 4.5-rc1. Lots of gadget driver
updates and fixes, like usual, and a mix of other USB driver updates as
well. Full details in the shortlog. All of these have been in
linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlaV2rUACgkQMUfUDdst+ym2XQCgqdDOlyGX5B//9CZ2kH1DrDW9
qLsAoLSBvw4hk+Aotv6tn8AayMpHwqV1
=pFLC
-----END PGP SIGNATURE-----
Merge tag 'usb-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB drivers update for 4.5-rc1.
Lots of gadget driver updates and fixes, like usual, and a mix of
other USB driver updates as well. Full details in the shortlog. All
of these have been in linux-next for a while"
* tag 'usb-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (191 commits)
MAINTAINERS: change my email address
USB: usbmon: remove assignment from IS_ERR argument
USB: mxu11x0: drop redundant function name from error messages
USB: mxu11x0: fix debug-message typos
USB: mxu11x0: rename usb-serial driver
USB: mxu11x0: fix modem-control handling on B0-transitions
USB: mxu11x0: fix memory leak on firmware download
USB: mxu11x0: fix memory leak in port-probe error path
USB: serial: add Moxa UPORT 11x0 driver
USB: cp210x: add ID for ELV Marble Sound Board 1
usb: chipidea: otg: use usb autosuspend to suspend bus for HNP
usb: chipidea: host: set host to be null after hcd is freed
usb: chipidea: removing of_find_property
usb: chipidea: implement platform shutdown callback
usb: chipidea: clean up CONFIG_USB_CHIPIDEA_DEBUG reference
usb: chipidea: delete static debug support
usb: chipidea: support debugfs without CONFIG_USB_CHIPIDEA_DEBUG
usb: chipidea: udc: improve error handling on _hardware_enqueue
usb: chipidea: udc: _ep_queue and _hw_queue cleanup
usb: dwc3: of-simple: fix build warning on !PM
...
This patch adds last time that user requested filesystem operations.
This information is used to detect whether system is idle or not later.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
MCP4726 is a single channel 12-bit DAC. We can support MCP4726 with
a little changes to mcp4725 driver. In power-down mode, they have
different selection of VOUT pull-down registers.
MCP4726 also has features:
- Output gain options: 1x, 2x
- Voltage reference selection: VDD, VREF (Unbuffered or Buffered)
But these are not supported in this change. (1x gain, VDD is selected)
datasheet: http://ww1.microchip.com/downloads/en/DeviceDoc/22272C.pdf
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds following attributes to watchdog device's sysfs interface
to read its different status.
* state - reads whether device is active or not
* identity - reads Watchdog device's identity string.
* timeout - reads current timeout.
* timeleft - reads timeleft before watchdog generates a reset
* bootstatus - reads status of the watchdog device at boot
* status - reads watchdog device's internal status bits
* nowayout - reads whether nowayout feature was set or not
Testing with iTCO_wdt:
# cd /sys/class/watchdog/watchdog1/
# ls
bootstatus dev device identity nowayout power state
subsystem timeleft timeout uevent
# cat identity
iTCO_wdt
# cat timeout
30
# cat state
inactive
# echo > /dev/watchdog1
# cat timeleft
26
# cat state
active
# cat bootstatus
0
# cat nowayout
0
Signed-off-by: Pratyush Anand <panand@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Linus Torvalds
Stefan Richter
Sinan Kaya
Christophe Lombard
Heiner Kallweit
Greg Kroah-Hartman
David S. Miller
Antonio Quartulli
Linus Luessing
Sanchayan Maity
João Paulo Rechi Vita
Shuoran Liu
Chao Yu
Cristina Moraru
Mimi Zohar
Wolfram Sang
Gabriel Somlo
Linus Walleij
Marc Andre
K. Y. Srinivasan
Andrew F. Davis
Matt Ranostay
Jaegeuk Kim
Akinobu Mita
Pratyush Anand