Pull drm fixes from Dave Airlie:
"Unfortunately this contains no easter eggs, its a bit larger than I'd
like, but I included a patch that just moves code from one file to
another and I'd like to avoid merge conflicts with that later, so it
makes it seem worse than it is,
Otherwise:
- radeon: fixes to use new microcode to stabilise some cards, use
some common displayport code, some runtime pm fixes, pll regression
fixes
- i915: fix for some context oopses, a warn in a used path, backlight
fixes
- nouveau: regression fix
- omap: a bunch of fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (51 commits)
drm: bochs: drop unused struct fields
drm: bochs: add power management support
drm: cirrus: add power management support
drm: Split out drm_probe_helper.c from drm_crtc_helper.c
drm/plane-helper: Don't fake-implement primary plane disabling
drm/ast: fix value check in cbr_scan2
drm/nouveau/bios: fix a bit shift error introduced by 457e77b
drm/radeon/ci: make sure mc ucode is loaded before checking the size
drm/radeon/si: make sure mc ucode is loaded before checking the size
drm/radeon: improve PLL params if we don't match exactly v2
drm/radeon: memory leak on bo reservation failure. v2
drm/radeon: fix VCE fence command
drm/radeon: re-enable mclk dpm on R7 260X asics
drm/radeon: add support for newer mc ucode on CI (v2)
drm/radeon: add support for newer mc ucode on SI (v2)
drm/radeon: apply more strict limits for PLL params v2
drm/radeon: update CI DPM powertune settings
drm/radeon: fix runpm handling on APUs (v4)
drm/radeon: disable mclk dpm on R7 260X
drm/tegra: Remove gratuitous pad field
...
Some i2c fixes over DisplayPort.
* 'drm-next-3.15-wip' of git://people.freedesktop.org/~deathsimple/linux:
drm/radeon: Improve vramlimit module param documentation
drm/radeon: fix audio pin counts for DCE6+ (v2)
drm/radeon/dp: switch to the common i2c over aux code
drm/dp/i2c: Update comments about common i2c over dp assumptions (v3)
drm/dp/i2c: send bare addresses to properly reset i2c connections (v4)
drm/radeon/dp: handle zero sized i2c over aux transactions (v2)
drm/i915: support address only i2c-over-aux transactions
drm/tegra: dp: Support address-only I2C-over-AUX transactions
Pull more networking fixes from David Miller:
1) Fix mlx4_en_netpoll implementation, it needs to schedule a NAPI
context, not synchronize it. From Chris Mason.
2) Ipv4 flow input interface should never be zero, it should be
LOOPBACK_IFINDEX instead. From Cong Wang and Julian Anastasov.
3) Properly configure MAC to PHY connection in mvneta devices, from
Thomas Petazzoni.
4) sys_recv should use SYSCALL_DEFINE. From Jan Glauber.
5) Tunnel driver ioctls do not use the correct namespace, fix from
Nicolas Dichtel.
6) Fix memory leak on seccomp filter attach, from Kees Cook.
7) Fix lockdep warning for nested vlans, from Ding Tianhong.
8) Crashes can happen in SCTP due to how the auth_enable value is
managed, fix from Vlad Yasevich.
9) Wireless fixes from John W Linville and co.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (45 commits)
net: sctp: cache auth_enable per endpoint
tg3: update rx_jumbo_pending ring param only when jumbo frames are enabled
vlan: Fix lockdep warning when vlan dev handle notification
seccomp: fix memory leak on filter attach
isdn: icn: buffer overflow in icn_command()
ip6_tunnel: use the right netns in ioctl handler
sit: use the right netns in ioctl handler
ip_tunnel: use the right netns in ioctl handler
net: use SYSCALL_DEFINEx for sys_recv
net: mdio-gpio: Add support for separate MDI and MDO gpio pins
net: mdio-gpio: Add support for active low gpio pins
net: mdio-gpio: Use devm_ functions where possible
ipv4, route: pass 0 instead of LOOPBACK_IFINDEX to fib_validate_source()
ipv4, fib: pass LOOPBACK_IFINDEX instead of 0 to flowi4_iif
mlx4_en: don't use napi_synchronize inside mlx4_en_netpoll
net: mvneta: properly configure the MAC <-> PHY connection in all situations
net: phy: add minimal support for QSGMII PHY
sfc:On MCDI timeout, issue an FLR (and mark MCDI to fail-fast)
mwifiex: fix hung task on command timeout
mwifiex: process event before command response
...
Here are a few driver fixes for char/misc drivers that resolve reported
issues.
All have been in linux-next successfully for a few days.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlNRlx4ACgkQMUfUDdst+ylYCgCdHm8SDiXwRfhUQJcYYlXrI1xs
skwAn3p1ydnIyVZJ/B3uxTA/0/1Jof5Z
=no/7
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a few driver fixes for char/misc drivers that resolve
reported issues.
All have been in linux-next successfully for a few days"
* tag 'char-misc-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Drivers: hv: vmbus: Negotiate version 3.0 when running on ws2012r2 hosts
Tools: hv: Handle the case when the target file exists correctly
vme_tsi148: Utilize to_pci_dev() macro
vme_tsi148: Fix PCI address mapping assumption
vme_tsi148: Fix typo in tsi148_slave_get()
w1: avoid recursive device_add
w1: fix netlink refcnt leak on error path
misc: Grammar s/addition/additional/
drivers: mcb: fix memory leak in chameleon_parse_cells() error path
mei: ignore client writing state during cb completion
mei: me: do not load the driver if the FW doesn't support MEI interface
GenWQE: Increase driver version number
GenWQE: Fix multithreading problems
GenWQE: Ensure rc is not returning an uninitialized value
GenWQE: Add wmb before DDCB is started
GenWQE: Enable access to VPD flash area
Here are some driver core fixes for 3.15-rc2. Also in here are some
documentation updates, as well as an API removal that had to wait for
after -rc1 due to the cleanups coming into you from multiple developer
trees (this one and the PPC tree.)
All have been in linux next successfully.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlNRl6cACgkQMUfUDdst+yllxACfV9fZ/A6IQja60AdPEo+oa6Cw
RiIAoJtH0D0G0eC4+/Qs9GSRMoB4jPPC
=Wi3a
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some driver core fixes for 3.15-rc2. Also in here are some
documentation updates, as well as an API removal that had to wait for
after -rc1 due to the cleanups coming into you from multiple developer
trees (this one and the PPC tree.)
All have been in linux next successfully"
* tag 'driver-core-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
drivers/base/dd.c incorrect pr_debug() parameters
Documentation: Update stable address in Chinese and Japanese translations
topology: Fix compilation warning when not in SMP
Chinese: add translation of io_ordering.txt
stable_kernel_rules: spelling/word usage
sysfs, driver-core: remove unused {sysfs|device}_schedule_callback_owner()
kernfs: protect lazy kernfs_iattrs allocation with mutex
fs: Don't return 0 from get_anon_bdev
Merge misc fixes from Andrew Morton:
"13 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
thp: close race between split and zap huge pages
mm: fix new kernel-doc warning in filemap.c
mm: fix CONFIG_DEBUG_VM_RB description
mm: use paravirt friendly ops for NUMA hinting ptes
mips: export flush_icache_range
mm/hugetlb.c: add cond_resched_lock() in return_unused_surplus_pages()
wait: explain the shadowing and type inconsistencies
Shiraz has moved
Documentation/vm/numa_memory_policy.txt: fix wrong document in numa_memory_policy.txt
powerpc/mm: fix ".__node_distance" undefined
kernel/watchdog.c:touch_softlockup_watchdog(): use raw_cpu_write()
init/Kconfig: move the trusted keyring config option to general setup
vmscan: reclaim_clean_pages_from_list() must use mod_zone_page_state()
David Vrabel identified a regression when using automatic NUMA balancing
under Xen whereby page table entries were getting corrupted due to the
use of native PTE operations. Quoting him
Xen PV guest page tables require that their entries use machine
addresses if the preset bit (_PAGE_PRESENT) is set, and (for
successful migration) non-present PTEs must use pseudo-physical
addresses. This is because on migration MFNs in present PTEs are
translated to PFNs (canonicalised) so they may be translated back
to the new MFN in the destination domain (uncanonicalised).
pte_mknonnuma(), pmd_mknonnuma(), pte_mknuma() and pmd_mknuma()
set and clear the _PAGE_PRESENT bit using pte_set_flags(),
pte_clear_flags(), etc.
In a Xen PV guest, these functions must translate MFNs to PFNs
when clearing _PAGE_PRESENT and translate PFNs to MFNs when setting
_PAGE_PRESENT.
His suggested fix converted p[te|md]_[set|clear]_flags to using
paravirt-friendly ops but this is overkill. He suggested an alternative
of using p[te|md]_modify in the NUMA page table operations but this is
does more work than necessary and would require looking up a VMA for
protections.
This patch modifies the NUMA page table operations to use paravirt
friendly operations to set/clear the flags of interest. Unfortunately
this will take a performance hit when updating the PTEs on
CONFIG_PARAVIRT but I do not see a way around it that does not break
Xen.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: David Vrabel <david.vrabel@citrix.com>
Tested-by: David Vrabel <david.vrabel@citrix.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Steven Noonan <steven@uplinklabs.net>
Cc: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stick in a comment before someone else tries to fix the sparse warning
this generates.
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/n/tip-o2ro6f3vkxklni0bc8f7m68s@git.kernel.org
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
shiraz.hashim@st.com email-id doesn't exist anymore as he has left the
company. Replace ST's id with shiraz.linux.kernel@gmail.com.
It also updates .mailmap file to fix address for 'git shortlog'.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, it is possible to create an SCTP socket, then switch
auth_enable via sysctl setting to 1 and crash the system on connect:
Oops[#1]:
CPU: 0 PID: 0 Comm: swapper Not tainted 3.14.1-mipsgit-20140415 #1
task: ffffffff8056ce80 ti: ffffffff8055c000 task.ti: ffffffff8055c000
[...]
Call Trace:
[<ffffffff8043c4e8>] sctp_auth_asoc_set_default_hmac+0x68/0x80
[<ffffffff8042b300>] sctp_process_init+0x5e0/0x8a4
[<ffffffff8042188c>] sctp_sf_do_5_1B_init+0x234/0x34c
[<ffffffff804228c8>] sctp_do_sm+0xb4/0x1e8
[<ffffffff80425a08>] sctp_endpoint_bh_rcv+0x1c4/0x214
[<ffffffff8043af68>] sctp_rcv+0x588/0x630
[<ffffffff8043e8e8>] sctp6_rcv+0x10/0x24
[<ffffffff803acb50>] ip6_input+0x2c0/0x440
[<ffffffff8030fc00>] __netif_receive_skb_core+0x4a8/0x564
[<ffffffff80310650>] process_backlog+0xb4/0x18c
[<ffffffff80313cbc>] net_rx_action+0x12c/0x210
[<ffffffff80034254>] __do_softirq+0x17c/0x2ac
[<ffffffff800345e0>] irq_exit+0x54/0xb0
[<ffffffff800075a4>] ret_from_irq+0x0/0x4
[<ffffffff800090ec>] rm7k_wait_irqoff+0x24/0x48
[<ffffffff8005e388>] cpu_startup_entry+0xc0/0x148
[<ffffffff805a88b0>] start_kernel+0x37c/0x398
Code: dd0900b8 000330f8 0126302d <dcc60000> 50c0fff1 0047182a a48306a0
03e00008 00000000
---[ end trace b530b0551467f2fd ]---
Kernel panic - not syncing: Fatal exception in interrupt
What happens while auth_enable=0 in that case is, that
ep->auth_hmacs is initialized to NULL in sctp_auth_init_hmacs()
when endpoint is being created.
After that point, if an admin switches over to auth_enable=1,
the machine can crash due to NULL pointer dereference during
reception of an INIT chunk. When we enter sctp_process_init()
via sctp_sf_do_5_1B_init() in order to respond to an INIT chunk,
the INIT verification succeeds and while we walk and process
all INIT params via sctp_process_param() we find that
net->sctp.auth_enable is set, therefore do not fall through,
but invoke sctp_auth_asoc_set_default_hmac() instead, and thus,
dereference what we have set to NULL during endpoint
initialization phase.
The fix is to make auth_enable immutable by caching its value
during endpoint initialization, so that its original value is
being carried along until destruction. The bug seems to originate
from the very first days.
Fix in joint work with Daniel Borkmann.
Reported-by: Joshua Kinard <kumba@gentoo.org>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Joshua Kinard <kumba@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Mostly cxgb4 fixes unblocked by the merge of some prerequisites via
the net tree.
- Drop deprecated MSI-X API use.
- A couple other miscellaneous things.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/PTZ
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma updates from Roland Dreier:
- mostly cxgb4 fixes unblocked by the merge of some prerequisites via
the net tree
- drop deprecated MSI-X API use.
- a couple other miscellaneous things.
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/cxgb4: Fix over-dereference when terminating
RDMA/cxgb4: Use uninitialized_var()
RDMA/cxgb4: Add missing debug stats
RDMA/cxgb4: Initialize reserved fields in a FW work request
RDMA/cxgb4: Use pr_warn_ratelimited
RDMA/cxgb4: Max fastreg depth depends on DSGL support
RDMA/cxgb4: SQ flush fix
RDMA/cxgb4: rmb() after reading valid gen bit
RDMA/cxgb4: Endpoint timeout fixes
RDMA/cxgb4: Use the BAR2/WC path for kernel QPs and T5 devices
IB/mlx5: Add block multicast loopback support
IB/mthca: Use pci_enable_msix_exact() instead of pci_enable_msix()
IB/qib: Use pci_enable_msix_range() instead of pci_enable_msix()
Add an empty version of of_find_node_by_path().
This fixes following build error for asoc tree:
sound/soc/fsl/fsl_ssi.c: In function 'fsl_ssi_probe':
sound/soc/fsl/fsl_ssi.c:1471:2: error: implicit declaration of function 'of_find_node_by_path' [-Werror=implicit-function-declaration]
sprop = of_get_property(of_find_node_by_path("/"), "compatible", NULL);
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Rob Herring <robh@kernel.org>
This is leftover stuff from my previous doc round which I kinda wanted
to do but didn't yet due to rebase hell.
The modeset helpers and the probing helpers a independent and e.g.
i915 uses the probing stuff but has its own modeset infrastructure. It
hence makes to split this up. While at it add a DOC: comment for the
probing libraray.
It would be rather neat to pull some of the DocBook documenting these
two helpers into in-line DOC: comments. But unfortunately kerneldoc
doesn't support markdown or something similar to make nice-looking
documentation, so the current state is better.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Merge ipmi fixes from Corey Minyard:
"Things collected since last kernel release.
Some of these are pretty important. The first three are bug fixes.
The next two are to hopefully make everyone happy about allowing
ACPI to be on all the time and not have IPMI have an effect on the
system when not in use. The last is a little cleanup"
* emailed patches from Corey Minyard <cminyard@mvista.com>:
ipmi: boolify some things
ipmi: Turn off all activity on an idle ipmi interface
ipmi: Turn off default probing of interfaces
ipmi: Reset the KCS timeout when starting error recovery
ipmi: Fix a race restarting the timer
Char: ipmi_bt_sm, fix infinite loop
The IPMI driver would wake up periodically looking for events and
watchdog pretimeouts. If there is nothing waiting for these events,
it's really kind of pointless to be checking for them. So modify the
driver so the message handler can pass down if it needs the lower layer
to be waiting for these. Modify the system interface lower layer to
turn off all timer and thread activity if the upper layer doesn't need
anything and it is not currently handling messages. And modify the
message handler to not restart the timer if its timer is not needed.
The timers and kthread will still be enabled if:
- the SI interface is handling a message.
- a user has enabled watching for events.
- the IPMI watchdog timer is in use (since it uses pretimeouts).
- the message handler is waiting on a remote response.
- a user has registered to receive commands.
This mostly affects interfaces without interrupts. Interfaces with
interrupts already don't use CPU in the system interface when the
interface is idle.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86 fixes from Ingo Molnar:
"Various fixes:
- reboot regression fix
- build message spam fix
- GPU quirk fix
- 'make kvmconfig' fix
plus the wire-up of the renameat2() system call on i386"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Remove the PCI reboot method from the default chain
x86/build: Supress "Nothing to be done for ..." messages
x86/gpu: Fix sign extension issue in Intel graphics stolen memory quirks
x86/platform: Fix "make O=dir kvmconfig"
i386: Wire up the renameat2() syscall
Only ws2012r2 hosts support the ability to reconnect to the host on VMBUS. This functionality
is needed by kexec in Linux. To use this functionality we need to negotiate version 3.0 of the
VMBUS protocol.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: <stable@vger.kernel.org> [3.9+]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return the appropriate error code and handle the case when the target
file exists correctly. This fixes a bug.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: <stable@vger.kernel.org> [3.14]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is for a system with fixed assignments of input and output pins
(various variants of Kontron COMe).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some systems using mdio-gpio may use active-low gpio pins
(eg with inverters or FETs connected to all or some of the
gpio pins).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by Julian:
Simply, flowi4_iif must not contain 0, it does not
look logical to ignore all ip rules with specified iif.
because in fib_rule_match() we do:
if (rule->iifindex && (rule->iifindex != fl->flowi_iif))
goto out;
flowi4_iif should be LOOPBACK_IFINDEX by default.
We need to move LOOPBACK_IFINDEX to include/net/flow.h:
1) It is mostly used by flowi_iif
2) Fix the following compile error if we use it in flow.h
by the patches latter:
In file included from include/linux/netfilter.h:277:0,
from include/net/netns/netfilter.h:5,
from include/net/net_namespace.h:21,
from include/linux/netdevice.h:43,
from include/linux/icmpv6.h:12,
from include/linux/ipv6.h:61,
from include/net/ipv6.h:16,
from include/linux/sunrpc/clnt.h:27,
from include/linux/nfs_fs.h:30,
from init/do_mounts.c:32:
include/net/flow.h: In function ‘flowi4_init_output’:
include/net/flow.h:84:32: error: ‘LOOPBACK_IFINDEX’ undeclared (first use in this function)
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All device_schedule_callback_owner() users are converted to use
device_remove_file_self(). Remove now unused
{sysfs|device}_schedule_callback_owner().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds the necessary definitions for the PHY layer to
recognize "qsgmii" as a valid PHY interface. A QSMII interface, as
defined at
http://en.wikipedia.org/wiki/Media_Independent_Interface#Quad_Serial_Gigabit_Media_Independent_Interface,
is "is a method of combining four SGMII lines into a 5Gbit/s
interface. QSGMII, like SGMII, uses LVDS signalling for the TX and RX
data and a single LVDS clock signal. QSGMII uses significantly fewer
signal lines than four SGMII busses."
This type of MAC <-> PHY connection might require special handling on
the MAC driver side, so it should be possible to express this type of
MAC <-> PHY connection, for example in the Device Tree.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: devicetree@vger.kernel.org
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The version of the drm_tegra_submit structure that was merged all the
way back in 3.10 contains a pad field that was originally intended to
properly pad the following __u64 field. Unfortunately it seems like a
different field was dropped during review that caused this padding to
become unnecessary, but the pad field wasn't removed at that time.
One possible side-effect of this is that since the __u64 following the
pad is now no longer properly aligned, the compiler may (or may not)
introduce padding itself, which results in no predictable ABI.
Rectify this by removing the pad field so that all fields are again
naturally aligned. Technically this is breaking existing userspace ABI,
but given that there aren't any (released) userspace drivers that make
use of this yet, the fallout should be minimal.
Fixes: d43f81cbaf ("drm/tegra: Add gr2d device")
Cc: <stable@vger.kernel.org> # 3.10
Signed-off-by: Thierry Reding <treding@nvidia.com>
Steve reported a reboot hang and bisected it back to this commit:
a4f1987e4c x86, reboot: Add EFI and CF9 reboot methods into the default list
He heroically tested all reboot methods and found the following:
reboot=t # triple fault ok
reboot=k # keyboard ctrl FAIL
reboot=b # BIOS ok
reboot=a # ACPI FAIL
reboot=e # EFI FAIL [system has no EFI]
reboot=p # PCI 0xcf9 FAIL
And I think it's pretty obvious that we should only try PCI 0xcf9 as a
last resort - if at all.
The other observation is that (on this box) we should never try
the PCI reboot method, but close with either the 'triple fault'
or the 'BIOS' (terminal!) reboot methods.
Thirdly, CF9_COND is a total misnomer - it should be something like
CF9_SAFE or CF9_CAREFUL, and 'CF9' should be 'CF9_FORCE' ...
So this patch fixes the worst problems:
- it orders the actual reboot logic to follow the reboot ordering
pattern - it was in a pretty random order before for no good
reason.
- it fixes the CF9 misnomers and uses BOOT_CF9_FORCE and
BOOT_CF9_SAFE flags to make the code more obvious.
- it tries the BIOS reboot method before the PCI reboot method.
(Since 'BIOS' is a terminal reboot method resulting in a hang
if it does not work, this is essentially equivalent to removing
the PCI reboot method from the default reboot chain.)
- just for the miraculous possibility of terminal (resulting
in hang) reboot methods of triple fault or BIOS returning
without having done their job, there's an ordering between
them as well.
Reported-and-bisected-and-tested-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Li Aubrey <aubrey.li@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Link: http://lkml.kernel.org/r/20140404064120.GB11877@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull networking fixes from David Miller:
1) Fix BPF filter validation of netlink attribute accesses, from
Mathias Kruase.
2) Netfilter conntrack generation seqcount not initialized properly,
from Andrey Vagin.
3) Fix comparison mask computation on big-endian in nft_cmp_fast(),
from Patrick McHardy.
4) Properly limit MTU over ipv6, from Eric Dumazet.
5) Fix seccomp system call argument population on 32-bit, from Daniel
Borkmann.
6) skb_network_protocol() should not use hard-coded ETH_HLEN, instead
skb->mac_len needs to be used. From Vlad Yasevich.
7) We have several cases of using socket based communications to
implement a tunnel. For example, some tunnels are encapsulations
over UDP so we use an internal kernel UDP socket to do the
transmits.
These tunnels should behave just like other software devices and
pass the packets on down to the next layer.
Most importantly we want the top-level socket (eg TCP) that created
the traffic to be charged for the SKB memory.
However, once you get into the IP output path, we have code that
assumed that whatever was attached to skb->sk is an IP socket.
To keep the top-level socket being charged for the SKB memory,
whilst satisfying the needs of the IP output path, we now pass in an
explicit 'sk' argument.
From Eric Dumazet.
8) ping_init_sock() leaks group info, from Xiaoming Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
cxgb4: use the correct max size for firmware flash
qlcnic: Fix MSI-X initialization code
ip6_gre: don't allow to remove the fb_tunnel_dev
ipv4: add a sock pointer to dst->output() path.
ipv4: add a sock pointer to ip_queue_xmit()
driver/net: cosa driver uses udelay incorrectly
at86rf230: fix __at86rf230_read_subreg function
at86rf230: remove check if AVDD settled
net: cadence: Add architecture dependencies
net: Start with correct mac_len in skb_network_protocol
Revert "net: sctp: Fix a_rwnd/rwnd management to reflect real state of the receiver's buffer"
cxgb4: Save the correct mac addr for hw-loopback connections in the L2T
net: filter: seccomp: fix wrong decoding of BPF_S_ANC_SECCOMP_LD_W
seccomp: fix populating a0-a5 syscall args in 32-bit x86 BPF
qlcnic: Do not disable SR-IOV when VFs are assigned to VMs
qlcnic: Fix QLogic application/driver interface for virtual NIC configuration
qlcnic: Fix PVID configuration on eSwitch port.
qlcnic: Fix max ring count calculation
qlcnic: Fix to send INIT_NIC_FUNC as first mailbox.
qlcnic: Fix panic due to uninitialzed delayed_work struct in use.
...
In the dst->output() path for ipv4, the code assumes the skb it has to
transmit is attached to an inet socket, specifically via
ip_mc_output() : The sk_mc_loop() test triggers a WARN_ON() when the
provider of the packet is an AF_PACKET socket.
The dst->output() method gets an additional 'struct sock *sk'
parameter. This needs a cascade of changes so that this parameter can
be propagated from vxlan to final consumer.
Fixes: 8f646c922d ("vxlan: keep original skb ownership")
Reported-by: lucien xin <lucien.xin@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_queue_xmit() assumes the skb it has to transmit is attached to an
inet socket. Commit 31c70d5956 ("l2tp: keep original skb ownership")
changed l2tp to not change skb ownership and thus broke this assumption.
One fix is to add a new 'struct sock *sk' parameter to ip_queue_xmit(),
so that we do not assume skb->sk points to the socket used by l2tp
tunnel.
Fixes: 31c70d5956 ("l2tp: keep original skb ownership")
Reported-by: Zhan Jianyu <nasa4836@gmail.com>
Tested-by: Zhan Jianyu <nasa4836@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains three Netfilter fixes for your net tree,
they are:
* Fix missing generation sequence initialization which results in a splat
if lockdep is enabled, it was introduced in the recent works to improve
nf_conntrack scalability, from Andrey Vagin.
* Don't flush the GRE keymap list in nf_conntrack when the pptp helper is
disabled otherwise this crashes due to a double release, from Andrey
Vagin.
* Fix nf_tables cmp fast in big endian, from Patrick McHardy.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
While reviewing seccomp code, we found that BPF_S_ANC_SECCOMP_LD_W has
been wrongly decoded by commit a8fc927780 ("sk-filter: Add ability to
get socket filter program (v2)") into the opcode BPF_LD|BPF_B|BPF_ABS
although it should have been decoded as BPF_LD|BPF_W|BPF_ABS.
In practice, this should not have much side-effect though, as such
conversion is/was being done through prctl(2) PR_SET_SECCOMP. Reverse
operation PR_GET_SECCOMP will only return the current seccomp mode, but
not the filter itself. Since the transition to the new BPF infrastructure,
it's also not used anymore, so we can simply remove this as it's
unreachable.
Fixes: a8fc927780 ("sk-filter: Add ability to get socket filter program (v2)")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Francois reported that setting big mtu on loopback device could prevent
tcp sessions making progress.
We do not support (yet ?) IPv6 Jumbograms and cook corrupted packets.
We must limit the IPv6 MTU to (65535 + 40) bytes in theory.
Tested:
ifconfig lo mtu 70000
netperf -H ::1
Before patch : Throughput : 0.05 Mbits
After patch : Throughput : 35484 Mbits
Reported-by: Francois WELLENREITER <f.wellenreiter@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
nft_cmp_fast is used for equality comparisions of size <= 4. For
comparisions of size < 4 byte a mask is calculated that is applied to
both the data from userspace (during initialization) and the register
value (during runtime). Both values are stored using (in effect) memcpy
to a memory area that is then interpreted as u32 by nft_cmp_fast.
This works fine on little endian since smaller types have the same base
address, however on big endian this is not true and the smaller types
are interpreted as a big number with trailing zero bytes.
The mask therefore must not include the lower bytes, but the higher bytes
on big endian. Add a helper function that does a cpu_to_le32 to switch
the bytes on big endian. Since we're dealing with a mask of just consequitive
bits, this works out fine.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull slab changes from Pekka Enberg:
"The biggest change is byte-sized freelist indices which reduces slab
freelist memory usage:
https://lkml.org/lkml/2013/12/2/64"
* 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
mm: slab/slub: use page->list consistently instead of page->lru
mm/slab.c: cleanup outdated comments and unify variables naming
slab: fix wrongly used macro
slub: fix high order page allocation problem with __GFP_NOFAIL
slab: Make allocations with GFP_ZERO slightly more efficient
slab: make more slab management structure off the slab
slab: introduce byte sized index for the freelist of a slab
slab: restrict the number of objects in a slab
slab: introduce helper functions to get/set free object
slab: factor out calculate nr objects in cache_estimate
Pull yet more networking updates from David Miller:
1) Various fixes to the new Redpine Signals wireless driver, from
Fariya Fatima.
2) L2TP PPP connect code takes PMTU from the wrong socket, fix from
Dmitry Petukhov.
3) UFO and TSO packets differ in whether they include the protocol
header in gso_size, account for that in skb_gso_transport_seglen().
From Florian Westphal.
4) If VLAN untagging fails, we double free the SKB in the bridging
output path. From Toshiaki Makita.
5) Several call sites of sk->sk_data_ready() were referencing an SKB
just added to the socket receive queue in order to calculate the
second argument via skb->len. This is dangerous because the moment
the skb is added to the receive queue it can be consumed in another
context and freed up.
It turns out also that none of the sk->sk_data_ready()
implementations even care about this second argument.
So just kill it off and thus fix all these use-after-free bugs as a
side effect.
6) Fix inverted test in tcp_v6_send_response(), from Lorenzo Colitti.
7) pktgen needs to do locking properly for LLTX devices, from Daniel
Borkmann.
8) xen-netfront driver initializes TX array entries in RX loop :-) From
Vincenzo Maffione.
9) After refactoring, some tunnel drivers allow a tunnel to be
configured on top itself. Fix from Nicolas Dichtel.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (46 commits)
vti: don't allow to add the same tunnel twice
gre: don't allow to add the same tunnel twice
drivers: net: xen-netfront: fix array initialization bug
pktgen: be friendly to LLTX devices
r8152: check RTL8152_UNPLUG
net: sun4i-emac: add promiscuous support
net/apne: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
net: ipv6: Fix oif in TCP SYN+ACK route lookup.
drivers: net: cpsw: enable interrupts after napi enable and clearing previous interrupts
drivers: net: cpsw: discard all packets received when interface is down
net: Fix use after free by removing length arg from sk_data_ready callbacks.
Drivers: net: hyperv: Address UDP checksum issues
Drivers: net: hyperv: Negotiate suitable ndis version for offload support
Drivers: net: hyperv: Allocate memory for all possible per-pecket information
bridge: Fix double free and memory leak around br_allowed_ingress
bonding: Remove debug_fs files when module init fails
i40evf: program RSS LUT correctly
i40evf: remove open-coded skb_cow_head
ixgb: remove open-coded skb_cow_head
igbvf: remove open-coded skb_cow_head
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iEYEABECAAYFAlNFtEkACgkQuseO5dulBZVcPwCdFWY81hKqQaKHaSPFh9m+n1lt
yY0An2VZZGrFSkj162POFy1P2sPpGw5p
=LRFZ
-----END PGP SIGNATURE-----
Merge tag 'llvmlinux-for-v3.15' of git://git.linuxfoundation.org/llvmlinux/kernel
Pull llvm patches from Behan Webster:
"These are some initial updates to support compiling the kernel with
clang.
These patches have been through the proper reviews to the best of my
ability, and have been soaking in linux-next for a few weeks. These
patches by themselves still do not completely allow clang to be used
with the kernel code, but lay the foundation for other patches which
are still under review.
Several other of the LLVMLinux patches have been already added via
maintainer trees"
* tag 'llvmlinux-for-v3.15' of git://git.linuxfoundation.org/llvmlinux/kernel:
x86: LLVMLinux: Fix "incomplete type const struct x86cpu_device_id"
x86 kbuild: LLVMLinux: More cc-options added for clang
x86, acpi: LLVMLinux: Remove nested functions from Thinkpad ACPI
LLVMLinux: Add support for clang to compiler.h and new compiler-clang.h
LLVMLinux: Remove warning about returning an uninitialized variable
kbuild: LLVMLinux: Fix LINUX_COMPILER definition script for compilation with clang
Documentation: LLVMLinux: Update Documentation/dontdiff
kbuild: LLVMLinux: Adapt warnings for compilation with clang
kbuild: LLVMLinux: Add Kbuild support for building kernel with Clang
Pull SCSI target updates from Nicholas Bellinger:
"Here are the target pending updates for v3.15-rc1. Apologies in
advance for waiting until the second to last day of the merge window
to send these out.
The highlights this round include:
- iser-target support for T10 PI (DIF) offloads (Sagi + Or)
- Fix Task Aborted Status (TAS) handling in target-core (Alex Leung)
- Pass in transport supported PI at session initialization (Sagi + MKP + nab)
- Add WRITE_INSERT + READ_STRIP T10 PI support in target-core (nab + Sagi)
- Fix iscsi-target ERL=2 ASYNC_EVENT connection pointer bug (nab)
- Fix tcm_fc use-after-free of ft_tpg (Andy Grover)
- Use correct ib_sg_dma primitives in ib_isert (Mike Marciniszyn)
Also, note the virtio-scsi + vhost-scsi changes to expose T10 PI
metadata into KVM guest have been left-out for now, as there where a
few comments from MST + Paolo that where not able to be addressed in
time for v3.15. Please expect this feature for v3.16-rc1"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (43 commits)
ib_srpt: Use correct ib_sg_dma primitives
target/tcm_fc: Rename ft_tport_create to ft_tport_get
target/tcm_fc: Rename ft_{add,del}_lport to {add,del}_wwn
target/tcm_fc: Rename structs and list members for clarity
target/tcm_fc: Limit to 1 TPG per wwn
target/tcm_fc: Don't export ft_lport_list
target/tcm_fc: Fix use-after-free of ft_tpg
target: Add check to prevent Abort Task from aborting itself
target: Enable READ_STRIP emulation in target_complete_ok_work
target/sbc: Add sbc_dif_read_strip software emulation
target: Enable WRITE_INSERT emulation in target_execute_cmd
target/sbc: Add sbc_dif_generate software emulation
target/sbc: Only expose PI read_cap16 bits when supported by fabric
target/spc: Only expose PI mode page bits when supported by fabric
target/spc: Only expose PI inquiry bits when supported by fabric
target: Pass in transport supported PI at session initialization
target/iblock: Fix double bioset_integrity_free bug
Target/sbc: Initialize COMPARE_AND_WRITE write_sg scatterlist
target/rd: T10-Dif: RAM disk is allocating more space than required.
iscsi-target: Fix ERL=2 ASYNC_EVENT connection pointer bug
...
Pull media fixes from Mauro Carvalho Chehab:
"A series of bug fix patches for v3.15-rc1. Most are just driver
fixes. There are some changes at remote controller core level, fixing
some definitions on a new API added for Kernel v3.15.
It also adds the missing include at include/uapi/linux/v4l2-common.h,
to allow its compilation on userspace, as pointed by you"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (24 commits)
[media] gpsca: remove the risk of a division by zero
[media] stk1160: warrant a NUL terminated string
[media] v4l: ti-vpe: retain v4l2_buffer flags for captured buffers
[media] v4l: ti-vpe: Set correct field parameter for output and capture buffers
[media] v4l: ti-vpe: zero out reserved fields in try_fmt
[media] v4l: ti-vpe: Fix initial configuration queue data
[media] v4l: ti-vpe: Use correct bus_info name for the device in querycap
[media] v4l: ti-vpe: report correct capabilities in querycap
[media] v4l: ti-vpe: Allow usage of smaller images
[media] v4l: ti-vpe: Use video_device_release_empty
[media] v4l: ti-vpe: Make sure in job_ready that we have the needed number of dst_bufs
[media] lgdt3305: include sleep functionality in lgdt3304_ops
[media] drx-j: use customise option correctly
[media] m88rs2000: fix sparse static warnings
[media] r820t: fix size and init values
[media] rc-core: remove generic scancode filter
[media] rc-core: split dev->s_filter
[media] rc-core: do not change 32bit NEC scancode format for now
[media] rtl28xxu: remove duplicate ID 0458:707f Genius TVGo DVB-T03
[media] xc2028: add missing break to switch
...
ntb_netdev, a typo, and a leak of msix entries in the error path.
Clean ups of the event handling logic, as well as a overall style
cleanup. Finally, the driver was converted to use the new
pci_enable_msix_range logic (and the refactoring to go along with it).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=vDei
-----END PGP SIGNATURE-----
Merge tag 'ntb-3.15' of git://github.com/jonmason/ntb
Pull PCIe non-transparent bridge fixes and features from Jon Mason:
"NTB driver bug fixes to address issues in list traversal, skb leak in
ntb_netdev, a typo, and a leak of msix entries in the error path.
Clean ups of the event handling logic, as well as a overall style
cleanup. Finally, the driver was converted to use the new
pci_enable_msix_range logic (and the refactoring to go along with it)"
* tag 'ntb-3.15' of git://github.com/jonmason/ntb:
ntb: Use pci_enable_msix_range() instead of pci_enable_msix()
ntb: Split ntb_setup_msix() into separate BWD/SNB routines
ntb: Use pci_msix_vec_count() to obtain number of MSI-Xs
NTB: Code Style Clean-up
NTB: client event cleanup
ntb: Fix leakage of ntb_device::msix_entries[] array
NTB: Fix typo in setting one translation register
ntb_netdev: Fix skb free issue in open
ntb_netdev: Fix list_for_each_entry exit issue
Pull vfs updates from Al Viro:
"The first vfs pile, with deep apologies for being very late in this
window.
Assorted cleanups and fixes, plus a large preparatory part of iov_iter
work. There's a lot more of that, but it'll probably go into the next
merge window - it *does* shape up nicely, removes a lot of
boilerplate, gets rid of locking inconsistencie between aio_write and
splice_write and I hope to get Kent's direct-io rewrite merged into
the same queue, but some of the stuff after this point is having
(mostly trivial) conflicts with the things already merged into
mainline and with some I want more testing.
This one passes LTP and xfstests without regressions, in addition to
usual beating. BTW, readahead02 in ltp syscalls testsuite has started
giving failures since "mm/readahead.c: fix readahead failure for
memoryless NUMA nodes and limit readahead pages" - might be a false
positive, might be a real regression..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
missing bits of "splice: fix racy pipe->buffers uses"
cifs: fix the race in cifs_writev()
ceph_sync_{,direct_}write: fix an oops on ceph_osdc_new_request() failure
kill generic_file_buffered_write()
ocfs2_file_aio_write(): switch to generic_perform_write()
ceph_aio_write(): switch to generic_perform_write()
xfs_file_buffered_aio_write(): switch to generic_perform_write()
export generic_perform_write(), start getting rid of generic_file_buffer_write()
generic_file_direct_write(): get rid of ppos argument
btrfs_file_aio_write(): get rid of ppos
kill the 5th argument of generic_file_buffered_write()
kill the 4th argument of __generic_file_aio_write()
lustre: don't open-code kernel_recvmsg()
ocfs2: don't open-code kernel_recvmsg()
drbd: don't open-code kernel_recvmsg()
constify blk_rq_map_user_iov() and friends
lustre: switch to kernel_sendmsg()
ocfs2: don't open-code kernel_sendmsg()
take iov_iter stuff to mm/iov_iter.c
process_vm_access: tidy up a bit
...
design of tracepoints and how a user could register a tracepoint
and have that tracepoint not be activated but no error was shown.
The design was for an out of tree module but broke in tree users.
The clean up was to remove the saving of the hash table of tracepoint
names such that they can be enabled before they exist (enabling
a module tracepoint before that module is loaded). This added more
complexity than needed. The clean up was to remove that code and
just enable tracepoints that exist or fail if they do not.
This removed a lot of code as well as the complexity that it brought.
As a side effect, instead of registering a tracepoint by its name,
the tracepoint needs to be registered with the tracepoint descriptor.
This removes having to duplicate the tracepoint names that are
enabled.
The second patch was added that simplified the way modules were
searched for.
This cleanup required changes that were in the 3.15 queue as well as
some changes that were added late in the 3.14-rc cycle. This final
change waited till the two were merged in upstream and then the
change was added and full tests were run. Unfortunately, the
test found some errors, but after it was already submitted to the
for-next branch and not to be rebased. Sparse errors were detected
by Fengguang Wu's bot tests, and my internal tests discovered that
the anonymous union initialization triggered a bug in older gcc compilers.
Luckily, there was a bugzilla for the gcc bug which gave a work around
to the problem. The third and fourth patch handled the sparse error
and the gcc bug respectively.
A final patch was tagged along to fix a missing documentation for
the README file.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTR+pwAAoJEKQekfcNnQGuvfoH/A4XZu4/1h2ZuKhzGi6lrrWr
+zHUQ+JmGiAYRziQFwr2t/gqJ2vmDfHJnbDjKi6Emx8JcxesHas6CQOWps4zEic0
dwYSQjvuGNGFIFt+7I0K1OxfVVdt2PQ2lVrB5WgYdbash5J4Bi+09QBv0RbUKheo
37dKSeN3pbsuQsR70OTVP8laG3dA9IbHW7PsKnxIEB5zeIUHUBME/QdPPj/CuJwk
wxZjXC2dbc3rdRlQjTVtWV3ZkGgZJB0k+JxjvZTA0N6u8Hj8LiFPuNawzf7ceBHx
gc++57+WuMW0f0X/ar5/+3UPGFQKMSvKmdxIQCnWXQz5seTYYKDEx7mTH22fxgg=
=OgeQ
-----END PGP SIGNATURE-----
Merge tag 'trace-3.15-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull more tracing updates from Steven Rostedt:
"This includes the final patch to clean up and fix the issue with the
design of tracepoints and how a user could register a tracepoint and
have that tracepoint not be activated but no error was shown.
The design was for an out of tree module but broke in tree users. The
clean up was to remove the saving of the hash table of tracepoint
names such that they can be enabled before they exist (enabling a
module tracepoint before that module is loaded). This added more
complexity than needed. The clean up was to remove that code and just
enable tracepoints that exist or fail if they do not.
This removed a lot of code as well as the complexity that it brought.
As a side effect, instead of registering a tracepoint by its name, the
tracepoint needs to be registered with the tracepoint descriptor.
This removes having to duplicate the tracepoint names that are
enabled.
The second patch was added that simplified the way modules were
searched for.
This cleanup required changes that were in the 3.15 queue as well as
some changes that were added late in the 3.14-rc cycle. This final
change waited till the two were merged in upstream and then the change
was added and full tests were run. Unfortunately, the test found some
errors, but after it was already submitted to the for-next branch and
not to be rebased. Sparse errors were detected by Fengguang Wu's bot
tests, and my internal tests discovered that the anonymous union
initialization triggered a bug in older gcc compilers. Luckily, there
was a bugzilla for the gcc bug which gave a work around to the
problem. The third and fourth patch handled the sparse error and the
gcc bug respectively.
A final patch was tagged along to fix a missing documentation for the
README file"
* tag 'trace-3.15-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Add missing function triggers dump and cpudump to README
tracing: Fix anonymous unions in struct ftrace_event_call
tracepoint: Fix sparse warnings in tracepoint.c
tracepoint: Simplify tracepoint module search
tracepoint: Use struct pointer instead of name hash for reg/unreg tracepoints
Pull audit updates from Eric Paris.
* git://git.infradead.org/users/eparis/audit: (28 commits)
AUDIT: make audit_is_compat depend on CONFIG_AUDIT_COMPAT_GENERIC
audit: renumber AUDIT_FEATURE_CHANGE into the 1300 range
audit: do not cast audit_rule_data pointers pointlesly
AUDIT: Allow login in non-init namespaces
audit: define audit_is_compat in kernel internal header
kernel: Use RCU_INIT_POINTER(x, NULL) in audit.c
sched: declare pid_alive as inline
audit: use uapi/linux/audit.h for AUDIT_ARCH declarations
syscall_get_arch: remove useless function arguments
audit: remove stray newline from audit_log_execve_info() audit_panic() call
audit: remove stray newlines from audit_log_lost messages
audit: include subject in login records
audit: remove superfluous new- prefix in AUDIT_LOGIN messages
audit: allow user processes to log from another PID namespace
audit: anchor all pid references in the initial pid namespace
audit: convert PPIDs to the inital PID namespace.
pid: get pid_t ppid of task in init_pid_ns
audit: rename the misleading audit_get_context() to audit_take_context()
audit: Add generic compat syscall support
audit: Add CONFIG_HAVE_ARCH_AUDITSYSCALL
...
Pull NVMe driver updates from Matthew Wilcox:
"Various updates to the NVMe driver. The most user-visible change is
that drive hotplugging now works and CPU hotplug while an NVMe drive
is installed should also work better"
* git://git.infradead.org/users/willy/linux-nvme:
NVMe: Retry failed commands with non-fatal errors
NVMe: Add getgeo to block ops
NVMe: Start-stop nvme_thread during device add-remove.
NVMe: Make I/O timeout a module parameter
NVMe: CPU hot plug notification
NVMe: per-cpu io queues
NVMe: Replace DEFINE_PCI_DEVICE_TABLE
NVMe: Fix divide-by-zero in nvme_trans_io_get_num_cmds
NVMe: IOCTL path RCU protect queue access
NVMe: RCU protected access to io queues
NVMe: Initialize device reference count earlier
NVMe: Add CONFIG_PM_SLEEP to suspend/resume functions
particularly with a focus on RDMA.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
Comment: GPGTools - http://gpgtools.org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=yzy/
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs
Pull 9p changes from Eric Van Hensbergen:
"A bunch of updates and cleanup within the transport layer,
particularly with a focus on RDMA"
* tag 'for-linus-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
9pnet_rdma: check token type before int conversion
9pnet: trans_fd : allocate struct p9_trans_fd and struct p9_conn together.
9pnet: p9_client->conn field is unused. Remove it.
9P: Get rid of REQ_STATUS_FLSH
9pnet_rdma: add cancelled()
9pnet_rdma: update request status during send
9P: Add cancelled() to the transport functions.
net: Mark function as static in 9p/client.c
9P: Add memory barriers to protect request fields over cb/rpc threads handoff
- Fix for a recently introduced CPU hotplug regression in ARM KVM
from Ming Lei.
- Fixes for breakage in the at32ap, loongson2_cpufreq, and unicore32
cpufreq drivers introduced during the 3.14 cycle (-stable material)
from Chen Gang and Viresh Kumar.
- New powernv cpufreq driver from Vaidyanathan Srinivasan, with bits
from Gautham R Shenoy and Srivatsa S Bhat.
- Exynos cpufreq driver fix preventing it from being included into
multiplatform builds that aren't supported by it from Sachin Kamat.
- cpufreq cleanups related to the usage of the driver_data field in
struct cpufreq_frequency_table from Viresh Kumar.
- cpufreq ppc driver cleanup from Sachin Kamat.
- Intel BayTrail support for intel_idle and ACPI idle from Len Brown.
- Intel CPU model 54 (Atom N2000 series) support for intel_idle from
Jan Kiszka.
- intel_idle fix for Intel Ivy Town residency targets from Len Brown.
- turbostat updates (Intel Broadwell support and output cleanups)
from Len Brown.
- New cpuidle sysfs attribute for exporting C-states' target residency
information to user space from Daniel Lezcano.
- New kernel command line argument to prevent power domains enabled
by the bootloader from being turned off even if they are not in use
(for diagnostics purposes) from Tushar Behera.
- Fixes for wakeup sysfs attributes documentation from Geert Uytterhoeven.
- New ACPI video blacklist entry for ThinkPad Helix from Stephen Chandler
Paul.
- Assorted ACPI cleanups and a Kconfig help update from Jonghwan Choi,
Zhihui Zhang, Hanjun Guo.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=hGKg
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.15-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management fixes and updates from Rafael Wysocki:
"This is PM and ACPI material that has emerged over the last two weeks
and one fix for a CPU hotplug regression introduced by the recent CPU
hotplug notifiers registration series.
Included are intel_idle and turbostat updates from Len Brown (these
have been in linux-next for quite some time), a new cpufreq driver for
powernv (that might spend some more time in linux-next, but BenH was
asking me so nicely to push it for 3.15 that I couldn't resist), some
cpufreq fixes and cleanups (including fixes for some silly breakage in
a couple of cpufreq drivers introduced during the 3.14 cycle),
assorted ACPI cleanups, wakeup framework documentation fixes, a new
sysfs attribute for cpuidle and a new command line argument for power
domains diagnostics.
Specifics:
- Fix for a recently introduced CPU hotplug regression in ARM KVM
from Ming Lei.
- Fixes for breakage in the at32ap, loongson2_cpufreq, and unicore32
cpufreq drivers introduced during the 3.14 cycle (-stable material)
from Chen Gang and Viresh Kumar.
- New powernv cpufreq driver from Vaidyanathan Srinivasan, with bits
from Gautham R Shenoy and Srivatsa S Bhat.
- Exynos cpufreq driver fix preventing it from being included into
multiplatform builds that aren't supported by it from Sachin Kamat.
- cpufreq cleanups related to the usage of the driver_data field in
struct cpufreq_frequency_table from Viresh Kumar.
- cpufreq ppc driver cleanup from Sachin Kamat.
- Intel BayTrail support for intel_idle and ACPI idle from Len Brown.
- Intel CPU model 54 (Atom N2000 series) support for intel_idle from
Jan Kiszka.
- intel_idle fix for Intel Ivy Town residency targets from Len Brown.
- turbostat updates (Intel Broadwell support and output cleanups)
from Len Brown.
- New cpuidle sysfs attribute for exporting C-states' target
residency information to user space from Daniel Lezcano.
- New kernel command line argument to prevent power domains enabled
by the bootloader from being turned off even if they are not in use
(for diagnostics purposes) from Tushar Behera.
- Fixes for wakeup sysfs attributes documentation from Geert
Uytterhoeven.
- New ACPI video blacklist entry for ThinkPad Helix from Stephen
Chandler Paul.
- Assorted ACPI cleanups and a Kconfig help update from Jonghwan
Choi, Zhihui Zhang, Hanjun Guo"
* tag 'pm+acpi-3.15-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (28 commits)
ACPI: Update the ACPI spec information in Kconfig
arm, kvm: fix double lock on cpu_add_remove_lock
cpuidle: sysfs: Export target residency information
cpufreq: ppc: Remove duplicate inclusion of fsl_soc.h
cpufreq: create another field .flags in cpufreq_frequency_table
cpufreq: use kzalloc() to allocate memory for cpufreq_frequency_table
cpufreq: don't print value of .driver_data from core
cpufreq: ia64: don't set .driver_data to index
cpufreq: powernv: Select CPUFreq related Kconfig options for powernv
cpufreq: powernv: Use cpufreq_frequency_table.driver_data to store pstate ids
cpufreq: powernv: cpufreq driver for powernv platform
cpufreq: at32ap: don't declare local variable as static
cpufreq: loongson2_cpufreq: don't declare local variable as static
cpufreq: unicore32: fix typo issue for 'clk'
cpufreq: exynos: Disable on multiplatform build
PM / wakeup: Correct presence vs. emptiness of wakeup_* attributes
PM / domains: Add pd_ignore_unused to keep power domains enabled
ACPI / dock: Drop dock_device_ids[] table
ACPI / video: Favor native backlight interface for ThinkPad Helix
ACPI / thermal: Fix wrong variable usage in debug statement
...
Several spots in the kernel perform a sequence like:
skb_queue_tail(&sk->s_receive_queue, skb);
sk->sk_data_ready(sk, skb->len);
But at the moment we place the SKB onto the socket receive queue it
can be consumed and freed up. So this skb->len access is potentially
to freed up memory.
Furthermore, the skb->len can be modified by the consumer so it is
possible that the value isn't accurate.
And finally, no actual implementation of this callback actually uses
the length argument. And since nobody actually cared about it's
value, lots of call sites pass arbitrary values in such as '0' and
even '1'.
So just remove the length argument from the callback, that way there
is no confusion whatsoever and all of these use-after-free cases get
fixed as a side effect.
Based upon a patch by Eric Dumazet and his suggestion to audit this
issue tree-wide.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pullx86 core platform updates from Peter Anvin:
"This is the x86/platform branch with the objectionable IOSF patches
removed.
What is left is proper memory handling for Intel GPUs, and a change to
the Calgary IOMMU code which will be required to make kexec work
sanely on those platforms after some upcoming kexec changes"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, calgary: Use 8M TCE table size by default
x86/gpu: Print the Intel graphics stolen memory range
x86/gpu: Add Intel graphics stolen memory quirk for gen2 platforms
x86/gpu: Add vfunc for Intel graphics stolen memory base address
'struct page' has two list_head fields: 'lru' and 'list'. Conveniently,
they are unioned together. This means that code can use them
interchangably, which gets horribly confusing like with this nugget from
slab.c:
> list_del(&page->lru);
> if (page->active == cachep->num)
> list_add(&page->list, &n->slabs_full);
This patch makes the slab and slub code use page->lru universally instead
of mixing ->list and ->lru.
So, the new rule is: page->lru is what the you use if you want to keep
your page on a list. Don't like the fact that it's not called ->list?
Too bad.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Christoph Lameter <cl@linux.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Linus Torvalds
Dave Airlie
Mel Gorman
Peter Zijlstra
Viresh Kumar
Vlad Yasevich
Alexander Shiyan
Daniel Vetter
Corey Minyard
K. Y. Srinivasan
Guenter Roeck
Cong Wang
Tejun Heo
Thomas Petazzoni
Thierry Reding
Ingo Molnar
Eric Dumazet
David S. Miller
Daniel Borkmann
Patrick McHardy
Dave Hansen