The previous commit added the ability to throttle stations when they queue
too much airtime in the hardware. This commit enables the functionality by
calculating the expected airtime usage of each packet that is dequeued from
the TXQs in mac80211, and accounting that as pending airtime.
The estimated airtime for each skb is stored in the tx_info, so we can
subtract the same amount from the running total when the skb is freed or
recycled. The throttling mechanism relies on this accounting to be
accurate (i.e., that we are not freeing skbs without subtracting any
airtime they were accounted for), so we put the subtraction into
ieee80211_report_used_skb(). As an optimisation, we also subtract the
airtime on regular TX completion, zeroing out the value stored in the
packet afterwards, to avoid having to do an expensive lookup of the station
from the packet data on every packet.
This patch does *not* include any mechanism to wake a throttled TXQ again,
on the assumption that this will happen anyway as a side effect of whatever
freed the skb (most commonly a TX completion).
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191119060610.76681-5-kyan@google.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order for the Fq_CoDel algorithm integrated in mac80211 layer to operate
effectively to control excessive queueing latency, the CoDel algorithm
requires an accurate measure of how long packets stays in the queue, AKA
sojourn time. The sojourn time measured at the mac80211 layer doesn't
include queueing latency in the lower layer (firmware/hardware) and CoDel
expects lower layer to have a short queue. However, most 802.11ac chipsets
offload tasks such TX aggregation to firmware or hardware, thus have a deep
lower layer queue.
Without a mechanism to control the lower layer queue size, packets only
stay in mac80211 layer transiently before being sent to firmware queue.
As a result, the sojourn time measured by CoDel in the mac80211 layer is
almost always lower than the CoDel latency target, hence CoDel does little
to control the latency, even when the lower layer queue causes excessive
latency.
The Byte Queue Limits (BQL) mechanism is commonly used to address the
similar issue with wired network interface. However, this method cannot be
applied directly to the wireless network interface. "Bytes" is not a
suitable measure of queue depth in the wireless network, as the data rate
can vary dramatically from station to station in the same network, from a
few Mbps to over Gbps.
This patch implements an Airtime-based Queue Limit (AQL) to make CoDel work
effectively with wireless drivers that utilized firmware/hardware
offloading. AQL allows each txq to release just enough packets to the lower
layer to form 1-2 large aggregations to keep hardware fully utilized and
retains the rest of the frames in mac80211 layer to be controlled by the
CoDel algorithm.
Signed-off-by: Kan Yan <kyan@google.com>
[ Toke: Keep API to set pending airtime internal, fix nits in commit msg ]
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191119060610.76681-4-kyan@google.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix recently added code to calculate airtime of packets to the mt76
driver. Import this into mac80211 so we can use it for airtime queue limit
calculations.
The airtime.c file is copied verbatim from the mt76 driver, and adjusted to
be usable in mac80211. This involves:
- Switching to mac80211 data structures.
- Adding support for 160 MHz channels and HE mode.
- Moving the symbol and duration calculations around a bit to avoid
rounding with the higher rates and longer symbol times used for HE rates.
The per-rate TX rate calculation is also split out to its own function so
it can be used directly for the AQL calculations later.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191119060610.76681-3-kyan@google.com
[fix HE_GROUP_IDX() to use 3 * bw, since there are 3 _gi values]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To implement airtime queue limiting, we need to keep a running account of
the estimated airtime of all skbs queued into the device. Do to this
correctly, we need to store the airtime estimate into the skb so we can
decrease the outstanding balance when the skb is freed. This means that the
time estimate must be stored somewhere that will survive for the lifetime
of the skb.
To get this, decrease the size of the ack_frame_id field to 6 bits, and
lower the size of the ID space accordingly. This leaves 10 bits for use for
tx_time_est, which is enough to store a maximum of 4096 us, if we shift the
values so they become units of 4us.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/157182474063.150713.16132669599100802716.stgit@toke.dk
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There really is no need to make drivers call the
ieee80211_start_tx_ba_cb_irqsafe() function and then
schedule the worker if all we want is to set a bit.
Add a new return value (that was previously considered
invalid) to indicate that the driver is immediately
ready for the session, and make drivers use it. The
only drivers that remain different are the Intel ones
as they need to negotiate more with the firmware.
Link: https://lore.kernel.org/r/1570007543-I152912660131cbab2e5d80b4218238c20f8a06e5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make it possibly for drivers to adjust the default max_mtu
by storing it in the hardware struct and using that value
for all interfaces.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Link: https://lore.kernel.org/r/1567738137-31748-1-git-send-email-wgong@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Store the OBSS PD parameters inside bss_conf when bringing up an AP and/or
when a station connects to an AP. This allows the driver to configure the
HW accordingly.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190730163701.18836-3-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Upon a successful assoc a station shall store the content of the HE
operation element inside bss_conf so that the driver can setup the
hardware accordingly.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20190729102342.8659-2-john@phrozen.org
[use struct copy]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add IEEE80211_KEY_FLAG_GENERATE_MMIE flag to ieee80211_key_flags in order
to allow the driver to notify mac80211 to generate MMIE and that it
requires sequence number generation only.
This is a preliminary patch to add BIP_CMAC_128 hw support to mt7615
driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/dfe275f9aa0f1cc6b33085f9efd5d8447f68ad13.1563228405.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Right now struct ieee80211_tx_rate cannot hold HE rates. Lets use
struct ieee80211_tx_status instead. This will also make the code
future-proof for when we have EHT.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190714154419.11854-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extended Key ID allows A-MPDU sessions while rekeying as long as each
A-MPDU aggregates only MPDUs with one keyid together.
Drivers able to segregate MPDUs accordingly can tell mac80211 to not
stop A-MPDU sessions when rekeying by setting the new flag
IEEE80211_HW_AMPDU_KEYBORDER_SUPPORT.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Link: https://lore.kernel.org/r/20190629195015.19680-3-alexander@wetzel-home.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
1) Drop IEEE80211_HW_EXT_KEY_ID_NATIVE and let drivers directly set
the NL80211_EXT_FEATURE_EXT_KEY_ID flag.
2) Drop IEEE80211_HW_NO_AMPDU_KEYBORDER_SUPPORT and simply assume all
drivers are unable to handle A-MPDU key borders.
The new Extended Key ID API now requires all mac80211 drivers to set
NL80211_EXT_FEATURE_EXT_KEY_ID when they implement set_key() and can
handle Extended Key ID. For drivers not providing set_key() mac80211
itself enables Extended Key ID support, using the internal SW crypto
services.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Link: https://lore.kernel.org/r/20190629195015.19680-2-alexander@wetzel-home.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since ieee80211_tx_dequeue() must not be called with softirqs enabled
(i.e. from process context without proper disable of bottom halves),
we add a wrapper that disables bottom halves before calling
ieee80211_tx_dequeue()
The new function is named ieee80211_tx_dequeue_ni() just as all other
from-process-context versions found in mac80211.
The documentation of ieee80211_tx_dequeue() is also updated so it
mentions that the function should not be called from process context.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Link: https://lore.kernel.org/r/20190617200140.6189-1-erik.stromdahl@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The remove_sta_debugfs callback in struct rate_control_ops is no longer
used by any driver, as there is no need for it (the debugfs directory is
already removed recursivly by the mac80211 core.) Because no one needs
it, just remove it to keep anyone else from accidentally using it in the
future.
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20190612142658.12792-5-gregkh@linuxfoundation.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This low level driver can find it useful to get the vif
when a remain on channel session is cancelled.
iwlwifi will need this soon.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20190723180001.5828-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no rate control algorithm that *doesn't* want to call
it internally, and calling it internally will let us modify
its behaviour in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow the userland daemon to en/disable TWT support for an AP.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
[simplify parsing code]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Turn TWT for STA interfaces when they associate and/or receive a
beacon where the twt_responder bit has changed.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IEEE 802.11 - 2016 forbids mixing MPDUs with different keyIDs in one
A-MPDU. Drivers supporting A-MPDUs and Extended Key ID must actively
enforce that requirement due to the available two unicast keyIDs.
Allow driver to signal mac80211 that they will not check the keyID in
MPDUs when aggregating them and that they expect mac80211 to stop Tx
aggregation when rekeying a connection using Extended Key ID.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* extended key ID support (from 802.11-2016)
* per-STA TX power control support
* mac80211 TX performance improvements
* HE (802.11ax) updates
* mesh link probing support
* enhancements of multi-BSSID support (also related to HE)
* OWE userspace processing support
-----BEGIN PGP SIGNATURE-----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=JQOx
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2019-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Various updates, notably:
* extended key ID support (from 802.11-2016)
* per-STA TX power control support
* mac80211 TX performance improvements
* HE (802.11ax) updates
* mesh link probing support
* enhancements of multi-BSSID support (also related to HE)
* OWE userspace processing support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The requirement for mesh link metric refreshing, is that from one
mesh point we be able to send some data frames to other mesh points
which are not currently selected as a primary traffic path, but which
are only 1 hop away. The absence of the primary path to the chosen node
makes it necessary to apply some form of marking on a chosen packet
stream so that the packets can be properly steered to the selected node
for testing, and not by the regular mesh path lookup.
Tested-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch introduce a new driver callback drv_sta_set_txpwr. This API will
copy the transmit power value passed from user space and call the driver
callback to set the tx power for the station.
Co-developed-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Ashok Raj Nagarajan <arnagara@codeaurora.org>
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for Extended Key ID as defined in IEEE 802.11-2016.
- Implement the nl80211 API for Extended Key ID
- Extend mac80211 API to allow drivers to support Extended Key ID
- Enable Extended Key ID by default for drivers only supporting SW
crypto (e.g. mac80211_hwsim)
- Allow unicast Tx usage to be supressed (IEEE80211_KEY_FLAG_NO_AUTO_TX)
- Select the decryption key based on the MPDU keyid
- Enforce existing assumptions in the code that rekeys don't change the
cipher
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[remove module parameter]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently there is no way for the driver to signal to mac80211 that it should
schedule a TXQ even if there are no packets on the mac80211 part of that queue.
This is problematic if the driver has an internal retry queue to deal with
software A-MPDU retry.
This patch changes the behavior of ieee80211_schedule_txq to always schedule
the queue, as its only user (ath9k) seems to expect such behavior already:
it calls this function on tx status and on powersave wakeup whenever its
internal retry queue is not empty.
Also add an extra argument to ieee80211_return_txq to get the same behavior.
This fixes an issue on ath9k where tx queues with packets to retry (and no
new packets in mac80211) would not get serviced.
Fixes: 89cea7493a ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Holding the lock around the entire duration of tx scheduling can create
some nasty lock contention, especially when processing airtime information
from the tx status or the rx path.
Improve locking by only holding the active_txq_lock for lookups / scheduling
list modifications.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers may want to track further the CSA beacons, for example
to compensate for buggy APs that change the beacon count or quiet
mode during CSA flow.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case we receive a beacon without CSA IE while we are in
the middle of channel switch - abort the operation.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018 REVmd of the spec introduces the max channel switch time
element which is optionally included in beacons/probes when there
is a channel switch / extended channel switch element.
The value represents the maximum delay between the time the AP
transmitted the last beacon in current channel and the expected
time of the first beacon in the new channel, in TU.
Parse the value and pass it to the driver.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set multi-bssid support flags according to driver support.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for multi-bssid.
This includes:
- Parsing multi-bssid element
- Overriding DTIM values
- Taking into account in various places the inner BSSID instead of
transmitter BSSID
- Save aside some multi-bssid properties needed by drivers
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix the missing and malformed documentation that kernel-doc and
sphinx warn about. While at it, also add some things to the docs
to fix missing links.
Sadly, the only way I could find to fix this was to add some
trailing whitespace.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There was a typo in the documentation for weight_multiplier in mac80211.h,
and the doc was missing entirely for airtime and airtime_weight in sta_info.h.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we reworked ieee80211_return_txq() so it assumes that the caller
takes care of logging, we need another function that can be called without
holding any locks. Introduce ieee80211_schedule_txq() which serves this
purpose.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some hardware (e.g. MediaTek MT7603) cannot report A-MPDU length in tx status
information. Add support for a flag to indicate that, to allow minstrel_ht
to use a fixed value in its internal calculation (which gives better results
than just defaulting to 1).
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds airtime accounting and scheduling to the mac80211 TXQ
scheduler. A new callback, ieee80211_sta_register_airtime(), is added
that drivers can call to report airtime usage for stations.
When airtime information is present, mac80211 will schedule TXQs
(through ieee80211_next_txq()) in a way that enforces airtime fairness
between active stations. This scheduling works the same way as the ath9k
in-driver airtime fairness scheduling. If no airtime usage is reported
by the driver, the scheduler will default to round-robin scheduling.
For drivers that don't control TXQ scheduling in software, a new API
function, ieee80211_txq_may_transmit(), is added which the driver can use
to check if the TXQ is eligible for transmission, or should be throttled to
enforce fairness. Calls to this function must also be enclosed in
ieee80211_txq_schedule_{start,end}() calls to ensure proper locking.
The API ieee80211_txq_may_transmit() also ensures that TXQ list will be
aligned aginst driver's own round-robin scheduler list. i.e it rotates
the TXQ list till it makes the requested node becomes the first entry
in TXQ list. Thus both the TXQ list and driver's list are in sync.
Co-developed-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Louie Lu <git@louie.lu>
[added debugfs write op to reset airtime counter]
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds an API to mac80211 to handle scheduling of TXQs. The interface
between driver and mac80211 for TXQ handling is changed by adding two new
functions: ieee80211_next_txq(), which will return the next TXQ to schedule
in the current round-robin rotation, and ieee80211_return_txq(), which the
driver uses to indicate that it has finished scheduling a TXQ (which will
then be put back in the scheduling rotation if it isn't empty).
The driver must call ieee80211_txq_schedule_start() at the start of each
scheduling session, and ieee80211_txq_schedule_end() at the end. The API
then guarantees that the same TXQ is not returned twice in the same
session (so a driver can loop on ieee80211_next_txq() without worrying
about breaking the loop.
Usage of the new API is optional, so drivers can be ported one at a time.
In this patch, the actual scheduling performed by mac80211 is simple
round-robin, but a subsequent commit adds airtime fairness awareness to the
scheduler.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
[minor kernel-doc fix, propagate sparse locking checks out]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
TWT is a feature that was added in 11ah and enhanced in
11ax. There are two bits that need to be set if we want
to use the feature in 11ax: one in the HE Capability IE
and one in the Extended Capability IE. This is because
of backward compatibility between 11ah and 11ax.
In order to simplify the flow for the low level driver
in managed mode, aggregate the two bits and add a boolean
that tells whether TWT is supported or not, but only if
11ax is supported.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the iwlwifi conversion, we sometimes call this from outside
of the wake_tx_queue() method, and in those cases must be in an
RCU critical section. Document this requirement.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases, like in the rsi driver hardware scan offload, there
may be scenarios in which hardware scan might not be available or
desirable.
Allow drivers to cope with this by letting them fall back to software
scan by returning the special value 1 from the hardware scan method.
Requested-by: Sushant Kumar Mishra <sushant2k1513@gmail.com>
Requested-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's nothing much for mac80211 to do, so only pass through
the requests with minimal checks and tracing. The driver must
call cfg80211's results APIs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Current mac80211 has provision to update tx status through
ieee80211_tx_status() and ieee80211_tx_status_ext(). But
drivers like ath10k updates the tx status from the skb except
txrate, txrate will be updated from a different path, peer stats.
Using ieee80211_tx_status_ext() in two different paths
(one for the stats, one for the tx rate) would duplicate
the stats instead.
To avoid this stats duplication, ieee80211_tx_rate_update()
is implemented.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
[minor commit message editing, use initializers in code]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
New bss param ftm_responder is used to notify the driver to
enable fine timing request (FTM) responder role in AP mode.
Plumb the new cfg80211 API for FTM responder statistics through to
the driver API in mac80211.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some hardwares have limitations on the packets' type in AMSDU.
Add an optional driver callback to determine if two skbs can
be used in the same AMSDU or not.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers may have AMSDU size limitation per TID, due to
HW constrains. Add an option to set this limit.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have a TXQ abstraction for non-data packets that need
powersave buffering. Since the AP cannot sleep, in case
of station we can use this TXQ for all management frames,
regardless if they are bufferable. Add HW flag to allow
that.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Toke Høiland-Jørgensen
Kan Yan
Joe Perches
Chris Packham
Johannes Berg
Wen Gong
John Crispin
Lorenzo Bianconi
Alexander Wetzel
Erik Stromdahl
Greg Kroah-Hartman
Emmanuel Grumbach
David S. Miller
Thomas Gleixner
Rajkumar Manoharan
Ashok Raj Nagarajan
Felix Fietkau
Sara Sharon
Toke Høiland-Jørgensen
Randy Dunlap
Anilkumar Kolli
Pradeep Kumar Chitrapu