This patch changes the declaration of Tx/Rx rings inside several loops. It
eliminates declaring the same rings every time for the duration of the loop,
instead declaring them once before the loop.
Change-ID: I59dea54276f18c47dca522f520c18f65fe42a15d
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order for the VF to achieve its programmed Tx rate, we need to set
the max credits value to 4. While we're at it, get rid of some magic
numbers.
Change-ID: I4f17b4d3a90f1e069bdd134a543f0aa22feac3a9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Because the hardware configures VF Tx rates in increments of 50 Mbps,
values smaller than that would be rounded down to 0, which was
interpreted as no limit at all. Rather than do this, we round up to 50
Mbps and notify the user.
Change-ID: I5275848233fe7514cf93e11323661c68f4c38737
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As recommended by the hardware guys, enable descriptor prefetch for
rings belonging to VFs. This matches a change already made for ring
belonging to the PF.
Change-ID: Idcc4dc7064bc9144ea81f5701ad07b7ecd11ba49
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the i40e_check_asq_alive check to ensure that the len register
offset is non-zero, indicating that SW has initialized the AQ.
Change-ID: I9c2e804788b4775bef9c7e80954ab004e6bdb306
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to e1000, e1000e, ixgbe and i40evf.
Emil provides a fix for ixgbe so that non-fiber devices with MNG FW enabled
are able to link at 100Mbps.
Jacob provides several changes for ixgbe, most of which are PTP related.
Renames ixgbe_ptp_enable() to ixgbe_ptp_feature_enable() to better reflect
the functions purpose. Extracts the hardware setup logic for the PTP
hardware bits from the ixgbe_ptp_set_ts_config() to enable future work for
the ixgbe_ptp_reset(). Maintain the hwstamp configuration through a reset
and extracts the creation of the PTP clock device from ptp_init() in order
to properly handle a suspend/resume cycle and only calls it if we don't
already have a ptp_clock pointer.
David provides a patch to expend the e1000e driver to turn on unicast
PROMISC when there is failure to write to a shared receive address register.
The fix update_phy_task() for 82579 is expanded to include newer PHYs as well
so that the dev_spec->eee_lp_ability has the correct value when going into
SX states.
Todd provides a e1000e fix an errata for 82574/82583 where it is possible
bad bits are read from SYSTIMH/L so check to see that the time is
incrementing at a reasonable rate and is a multiple of the time incremental
value. Removes a redundant igb PHY power down register write.
Andi Kleen out of lines two write functions for e1000e to save 30k text size.
Tobias Klauser converts the e1000 and i40evf drivers to use the
is_broadcast_ether_addr() and is_multicast_ether_addr().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the is_multicast_ether_addr helper function from linux/etherdevice.h
instead of open coding the multicast address check.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the is_broadcast_ether_addr/is_multicast_ether_addr helper functions
from linux/etherdevice.h instead of open coding them.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
One of the registers used to power down the PHY was found to be wrong
(should be bit 2 not bit 1) on further inspection it was also found to
be redundant.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Out of lining these two common inlines saves about 30k text size,
due to their errata workarounds.
14131431 2008136 1507328 17646895 10d452f vmlinux-before-e1000e
14101415 2004040 1507328 17612783 10cbfef vmlinux-e1000e
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, the update_phy_task was only calling e1000_set_eee_pchlan()
for phy.type 82579. This patch is to cause this function to be called
for 82579 and newer phy.types. This causes the dev_spec->eee_lp_ability
to have the correct value when going into SX states.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to a synchronization error, the value read from SYSTIML/SYSTIMH
might be incorrect.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, the check to turn on promiscuous mode only took into account
the total number of SHared Receive Address (SHRA) registers and if the
request was for a register within that range. It is possible that the
Management Engine might have locked a number of SHRA and not allowed a
new address to be written to the requested register.
Add a function to determine the number of unlocked SHRA registers. Then
determine if the number of registers available is sufficient for our needs,
if not then return -ENOMEM so that UNICAST PROMISC mode is activated.
Since the method by which ME claims SHRA registers is non-deterministic,
also add a return value to the function attempting to write an address
to a SHRA, and return a -E1000_ERR_CONFIG if the write fails. The error
will be passed up the function chain and allow the driver to also set
UNICAST PROMISC when this happens.
Cc: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Resume path calls .open but suspend path cannot call .stop because
fdirs should not be freed and control over hardware should not be
released until WoL is configured. To avoid having to duplicate all
changes made in .stop on suspend path split out part of .stop that
is relevant during suspend and call it from .stop and during suspend.
This fix also ensures that ixgbe_ptp_suspend is called during the
suspend path, and helps avoid similar errors. We can't call
ixgbe_ptp_stop, since it will free the PTP clock device, which we
shouldn't be doing during a suspend path.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we are adding proper support for suspend of PTP, extract out of
ixgbe_ptp_stop those things relevant to suspend. Then, have
ixgbe_ptp_stop call ixgbe_ptp_suspend. The next patch in the series will
have ixgbe_ptp_suspend called from the ixgbe_suspend path.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to properly handle a suspend/resume cycle, we cannot destroy
the PTP clock device. As part of this, we should only re-create the
device on first initialization. After a resume, when ixgbe_ptp_init is
called, we won't create a new clock, and we will use the old clock
device. To that end, this patch extracts the clock creation out of
ptp_init, and only calls it if we don't already have a ptp_clock
pointer.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rather than clearing the hwtstamp configuration, we should use the known
configuration requested by the user and call the function which has now
been separated from the ioctl. This means that after a reset, the
timestamp mode will be maintained rather than lost. We still can't
maintain the clock value, however.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently all of the hardware setup logic for the PTP hardware bits is
buried inside of the ioctl which sets the timestamp configuration. This
makes it hard to use this logic in other places (primarily reset), and
this means we can't restore current timestamp mode upon a MAC reset.
Extracting this logic into a separate function will enable future work
for the ixgbe_ptp_reset function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the name ixgbe_ptp_enable could be misconstrued as a function
which enables the whole PTP core, rename this function so that it is
clear the function is for enabling of the extra features such as PPS
signal.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver was calling setup_link to make sure that fiber interfaces with MNG FW
enabled will get link on probe because the laser was most likely turned off.
This prevented non-fiber devices with MNG FW from linking at 100Mbps.
This patch adds a check to only call setup_link for fiber devices.
Reported-and-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds xilinx CAN controller support. This driver supports both ZYNQ
CANPS and Soft IP AXI CAN controller.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Florian Fainelli says:
====================
net: sysfs: documentation updates
This patch set contains some updates to the sysfs Documentation for the
sysfs net class.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Document the network device statistics counter that are exposed as sysfs
attributes.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sysfs documentation for the various attributes of a network
interface exposed in /sys/class/<iface>/queues/{rx,tx}-<queue>/
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add documentation for the phys_port_id sysfs attribute of a network
device.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before f5efc69 ("netfilter: nf_tables: Add meta expression key for
bridge interface name"), the entire net/bridge/netfilter/ directory
depended on BRIDGE_NF_EBTABLES, ie. on ebtables. However, that
directory already contained the nf_tables bridge extension that
we should allow to compile separately. In f5efc69, we tried to
generalize this by using CONFIG_BRIDGE_NETFILTER which was not a good
idea since this option already existed and it is dedicated to enable
the Netfilter bridge IP/ARP filtering.
Let's try to fix this mess by:
1) making net/bridge/netfilter/ dependent on the toplevel
CONFIG_NETFILTER option, just like we do with the net/netfilter and
net/ipv{4,6}/netfilter/ directories.
2) Changing 'selects' to 'depends on' NETFILTER_XTABLES for
BRIDGE_NF_EBTABLES. I believe this problem was already before
f5efc69:
warning: (BRIDGE_NF_EBTABLES) selects NETFILTER_XTABLES which has
unmet direct dependencies (NET && INET && NETFILTER)
3) Fix ebtables/nf_tables bridge dependencies by making NF_TABLES_BRIDGE
and BRIDGE_NF_EBTABLES dependent on BRIDGE and NETFILTER:
warning: (NF_TABLES_BRIDGE && BRIDGE_NF_EBTABLES) selects
BRIDGE_NETFILTER which has unmet direct dependencies (NET && BRIDGE &&
NETFILTER && INET && NETFILTER_ADVANCED)
net/built-in.o: In function `br_parse_ip_options':
br_netfilter.c:(.text+0x4a5ba): undefined reference to `ip_options_compile'
br_netfilter.c:(.text+0x4a5ed): undefined reference to `ip_options_rcv_srr'
net/built-in.o: In function `br_nf_pre_routing_finish':
br_netfilter.c:(.text+0x4a8a4): undefined reference to `ip_route_input_noref'
br_netfilter.c:(.text+0x4a987): undefined reference to `ip_route_output_flow'
make: *** [vmlinux] Error 1
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit de906af1 (net: phy: make of_set_phy_supported work with genphy driver)
removed the last user of variable 'max_speed' in function
of_mdiobus_register_phy(), leading to compile warning "unused variable
‘max_speed’ [-Wunused-variable]". Thus remove it.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When cable is not present the clock speed of some of the devices is
reduced based upon power saving mode setting in NVRAM. Due to this
NVRAM reads take long time to complete as a result CPU soft lockup
message is seen. Fix is to override clock, disable link aware and link
idle modes before NVRAM reads and restore them back after the reads
are complete. During this period also check if the thread needs to be
rescheduled and if there are any signals to handle.
Also decrease the NVRAM command execution timeout value to 1ms.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kernel always invokes a pair of rtnl_lock adn rtnl_unlock to
protect dev_ethtool(), so its not neccessary to invoke spin_lock/unlock
in ethtool_ops.
Signed-off-by: Yang Wei <Wei.Yang@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sock_fprog and sock_fprog_kern are of equal size, however
it's cleaner to just use sizeof(*fprog) instead to always
have correct type.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it may then take longer than what the user specified using
setsockopt(SO_RCVTIMEO).
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Boyd says:
====================
ks8851 DT/regulator/gpio updates
This set of patches properly documents the micrel ks8851 spi ethernet
controller, converts to devm_regulator_get_optional() to make error
paths slightly simpler, and finally adds supports for another
optional regulator and a reset gpio. This allows me to use the ks8851
on my MSM8960 CDP board.
Changes since v1:
* Dropped vendor prefix patch as that should go through DT tree
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Users are currently just providing "ks8851" as the compatible for
this driver in device tree. Add a compatible string that provides
the vendor name along with the device name to be more explicit.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the ks8851 driver to enable an optional 1.8V vdd_io
regulator and assert the reset pin to the phy if a reset gpio is
present in device tree.
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simplifies error paths and removes the need to
regulator_put().
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ks8851 SPI ethernet wasn't documented, but we documented the
optional regulator supply for it under the mll based ethernet
chip. Furthermore, that compatible string needed another 'l'. Fix
all of this and document the optional vdd-io and reset-gpios
properties.
Cc: Nishanth Menon <nm@ti.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_alb.c
drivers/net/ethernet/altera/altera_msgdma.c
drivers/net/ethernet/altera/altera_sgdma.c
net/ipv6/xfrm6_output.c
Several cases of overlapping changes.
The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.
In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.
Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull sparc fixes from David Miller:
"A small bunch of bug fixes, in particular:
1) On older cpus we need a different chunk of virtual address space
to map the huge page TSB.
2) Missing memory barrier in Niagara2 memcpy.
3) trinity showed some places where fault validation was
unnecessarily loud on sparc64
4) Some sysfs printf's need a type adjustment, from Toralf Förster"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: fix format string mismatch in arch/sparc/kernel/sysfs.c
sparc64: Add membar to Niagara2 memcpy code.
sparc64: Fix huge TSB mapping on pre-UltraSPARC-III cpus.
sparc64: Don't bark so loudly about 32-bit tasks generating 64-bit fault addresses.
Pull networking fixes from David Miller:
"It looks like a sizeble collection but this is nearly 3 weeks of bug
fixing while you were away.
1) Fix crashes over IPSEC tunnels with NAT, the latter can reroute
the packet through a non-IPSEC protected path and the code has to
be able to handle SKBs attached to routes lacking an attached xfrm
state. From Steffen Klassert.
2) Fix OOPSs in ipv4 and ipv6 ipsec layers for unsupported
sub-protocols, also from Steffen Klassert.
3) Set local_df on fragmented netfilter skbs otherwise we won't be
able to forward successfully, from Florian Westphal.
4) cdc_mbim ipv6 neighbour code does __vlan_find_dev_deep without
holding RCU lock, from Bjorn Mork.
5) local_df test in ip_may_fragment is inverted, from Florian
Westphal.
6) jme driver doesn't check for DMA mapping failures, from Neil
Horman.
7) qlogic driver doesn't calculate number of TX queues properly, from
Shahed Shaikh.
8) fib_info_cnt can drift irreversibly positive if we fail to
allocate the fi->fib_metrics array, from Sergey Popovich.
9) Fix use after free in ip6_route_me_harder(), also from Sergey
Popovich.
10) When SYSCTL is disabled, we don't handle local_port_range and
ping_group_range defaults properly at all, from Cong Wang.
11) Unaccelerated VLAN tagged frames improperly handled by cdc_mbim
driver, fix from Bjorn Mork.
12) cassini driver needs nested lock annotations for TX locking, from
Emil Goode.
13) On init error ipv6 VTI driver can unregister pernet ops twice,
oops. Fix from Mahtias Krause.
14) If macvlan device is down, don't propagate IFF_ALLMULTI changes,
from Peter Christensen.
15) Missing NULL pointer check while parsing netlink config options in
ip6_tnl_validate(). From Susant Sahani.
16) Fix handling of neighbour entries during ipv6 router reachability
probing, from Duan Jiong.
17) x86 and s390 JIT address randomization has some address
calculation bugs leading to crashes, from Alexei Starovoitov and
Heiko Carstens.
18) Clear up those uglies with nop patching and net_get_random_once(),
from Hannes Frederic Sowa.
19) Option length miscalculated in ip6_append_data(), fix also from
Hannes Frederic Sowa.
20) A while ago we fixed a race during device unregistry when a
namespace went down, turns out there is a second place that needs
similar protection. From Cong Wang.
21) In the new Altera TSE driver multicast filtering isn't working,
disable it and just use promisc mode until the cause is found.
From Vince Bridgers.
22) When we disable router enabling in ipv6 we have to flush the
cached routes explicitly, from Duan Jiong.
23) NBMA tunnels should not cache routes on the tunnel object because
the key is variable, from Timo Teräs.
24) With stacked devices GRO information in skb->cb[] can be not setup
properly, make sure it is in all code paths. From Eric Dumazet.
25) Really fix stacked vlan locking, multiple levels of nesting with
intervening non-vlan devices are possible. From Vlad Yasevich.
26) Fallback ipip tunnel device's mtu is not setup properly, from
Steffen Klassert.
27) The packet scheduler's tcindex filter can crash because we
structure copy objects with list_head's inside, oops. From Cong
Wang.
28) Fix CHECKSUM_COMPLETE handling for ipv6 GRE tunnels, from Eric
Dumazet.
29) In some configurations 'itag' in __mkroute_input() can end up
being used uninitialized because of how fib_validate_source()
works. Fix it by explitly initializing itag to zero like all the
other fib_validate_source() callers do, from Li RongQing"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
batman: fix a bogus warning from batadv_is_on_batman_iface()
ipv4: initialise the itag variable in __mkroute_input
bonding: Send ALB learning packets using the right source
bonding: Don't assume 802.1Q when sending alb learning packets.
net: doc: Update references to skb->rxhash
stmmac: Remove unbalanced clk_disable call
ipv6: gro: fix CHECKSUM_COMPLETE support
net_sched: fix an oops in tcindex filter
can: peak_pci: prevent use after free at netdev removal
ip_tunnel: Initialize the fallback device properly
vlan: Fix build error wth vlan_get_encap_level()
can: c_can: remove obsolete STRICT_FRAME_ORDERING Kconfig option
MAINTAINERS: Pravin Shelar is Open vSwitch maintainer.
bnx2x: Convert return 0 to return rc
bonding: Fix alb mode to only use first level vlans.
bonding: Fix stacked device detection in arp monitoring
macvlan: Fix lockdep warnings with stacked macvlan devices
vlan: Fix lockdep warning with stacked vlan devices.
net: Allow for more then a single subclass for netif_addr_lock
net: Find the nesting level of a given device by type.
...
Daniel Borkmann says:
====================
BPF updates
These were still in my queue. Please see individual patches for
details.
I have rebased these on top of current net-next with Andrew's
gcc union fixup [1] applied to avoid dealing with an unnecessary
merge conflict.
[1] http://patchwork.ozlabs.org/patch/351577/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds three more test cases:
1) long jumps with holes of unreachable code
2) ret x
3) ldx + ret x
All three tests are for classical BPF and to make sure that
any changes will not break some exotic behaviour that exists
probably since decades. The last two tests are expected to
fail by the BPF checker already, as in classic BPF only K
or A are allowed to be returned. Thus, there are now 52 test
cases for BPF.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch simplifies and refactors the test case code a
bit and also adds a summary of all test that passed or
failed in the kernel log, so that it's easier to spot if
something has failed.
Future work could further extend the test framework to also
support different input 'stimuli' i.e. related structures
to seccomp.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mention the recently added test suite in the documentation file.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sk_unattached_filter_create() API is used by BPF filters that
are not directly attached or related to sockets, and are used in
team, ptp, xt_bpf, cls_bpf, etc. As such all users do their own
internal managment of obtaining filter blocks and thus already
have them in kernel memory and set up before calling into
sk_unattached_filter_create(). As a result, due to __user annotation
in sock_fprog, sparse triggers false positives (incorrect type in
assignment [different address space]) when filters are set up before
passing them to sk_unattached_filter_create(). Therefore, let
sk_unattached_filter_create() API use sock_fprog_kern to overcome
this issue.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lets get rid of this macro. After commit 5bcfedf06f ("net: filter:
simplify label names from jump-table"), labels have become more
readable due to omission of BPF_ prefix but at the same time more
generic, so that things like `git grep -n` would not find them. As
a middle path, lets get rid of the DL macro as it's not strictly
needed and would otherwise just hide the full name.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert says:
====================
net: Checksum offload changes - Part III
I am working on overhauling RX checksum offload. Goals of this effort
are:
- Specify what exactly it means when driver returns CHECKSUM_UNNECESSARY
- Preserve CHECKSUM_COMPLETE through encapsulation layers
- Don't do skb_checksum more than once per packet
- Unify GRO and non-GRO csum verification as much as possible
- Unify the checksum functions (checksum_init)
- Simply code
What is in this third patch set:
- Remove sk_no_check from sunrpc (doesn't seem to have any effect)
- Eliminate no_check from protosw. All protocols are using default of
zero for this
- Split sk_no_check into sk_no_check_tx and sk_no_check_rx
- Make enabling of UDP6 more restrictive and explicit
- Support zero UDP6 checksums in l2tp
V2: Took out vxlan changes to set zero csums in IPv6, this will
be in a later patch set.
V3: Fixed bug in restricting UDP6 checksums.
Please review carefully and test if possible, mucking with basic
checksum functions is always a little precarious :-)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Akeem G Abodunrin
Mitch Williams
Kevin Scott
David S. Miller
John W. Linville
Tobias Klauser
Todd Fujinaka
Andi Kleen
David Ertman
Jacob Keller
Emil Tantilov
Kedareswara rao Appana
Florian Fainelli
Pablo Neira
Christian Engelmayer
Prashant Sreedharan
Yang Wei
Daniel Borkmann
Arnaldo Carvalho de Melo
Stephen Boyd
Linus Torvalds