The AD5681R/AD5682R/AD5683/AD5683R are a family of one channel DACs with
12-bit, 14-bit and 16-bit precision respectively. The devices have either
no built-in reference, or built-in 2.5V reference.
These devices are similar to AD5691R/AD5692R/AD5693/AD5693R except
with a few notable differences:
* they use the SPI interface instead of I2C
* in the write control register, DB18 and DB17 are used for setting the
power mode, while DB16 is the REF bit. This is why a new regmap type
was defined and checked accordingly.
* the shift register is 24 bits wide, the first four bits are the command
bits followed by the data bits. As the data comprises of 20-bit, 18-bit
or 16-bit input code, this means that 4 LSB bits are don't care. This is
why the data needs to be shifted on the left with four bits. Therefore,
AD5683_REGMAP is checked inside a switch case in the ad5686_spi_write()
function. On the other hand, similar devices such as AD5693R family,
have the 4 MSB command bits followed by 4 don't care bits.
Datasheet:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5683R_5682R_5681R_5683.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD5691R/AD5692R/AD5693/AD5693R are a family of one channel DACs with
12-bit, 14-bit and 16-bit precision respectively. The devices have either
no built-in reference, or built-in 2.5V reference.
These devices are pretty similar to AD5671R/AD5675R and
AD5694/AD5694R/AD5695R/AD5696/AD5696R, except that they have one channel.
Another difference is that they use a write control register(addr 0x04) for
setting the power down modes and the internal reference instead of separate
registers for each function.
Datasheet:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5693R_5692R_5691R_5693.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A nice mix this time of excellent cleanups (many to send drivers
speeding toward staging graduations) and new drivers / device support.
A good part of this is Brian Masney's never ending task on the tsl2x7x
driver. The end is in sight so hopefully we'll get that one out of
staging very soon!
New device support
* AD5686
- Support AD5685R (was wrongly present as AD5685)
- Support AD5672R, AD5676, AD5676, AD5684R and AD5686R 4 and 8 channel
SPI DACs with various precisions.
- Support AD5671R, AD5675R, AD5694, AD5694R, AD5695R, AD5696 and AD5696R
I2C DACs with various percisions and numbers of channels.
* Analog front end rescale driver - New driver.
- Support current sensing usings a shunt resistor.
- Support simple voltage dividers.
- support simple current sense amplifiers.
* TI dac5571
- New driver and device bindings supporting:
dac5571, dac6571, dac7571, dac5574, dac6574, dac7574,
dac5573, dac6573 and dac7573
* Meson-adc
- Support for Meson AXG with DT bindings.
* mpu6050
- Support the mpu9255 which only requires additional WHOAMI entry and
compatible string.
* st_lsm6dsx
- Support for lsm330dlc combinded accelerometer and gyro sensors with
DT bindings.
* stm32_adc
- Add support for STM32MP1 with bindings.
Staging graduations
* adis16201 after some excelent cleanup by Himanshu Jha.
* adis16029 after some excelent cleanup by Shreeya Patel.
New features:
* ABI docs
- Add core ABI docs for angle channels.
* inv_mpu6050
- Provide support for the full range of interrupts the device
supports.
* st_accel
- Add SMO8840 ACPI ID seen in the wild on some Lenovo machines.
* stx104
- Provide a multiple gpio get function.
Cleanups / Minor fixes
* core
- Use new nested structure support to improve kernel-doc.
* ad2s1200
- Use be16_to_cpup instead of opencoding.
* ad5686
- Indentation tidy up.
- Switch to SPDX
- Refactor to allow various numbers of channels.
- Refactor to separate core and SPI specific support, prior to
addition of i2c equivalent devices.
* ad7606
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* ad7746
- Replace opencoded byte swapped i2c calls with _swapped variants.
- White space and line break readability improvements.
- Reorder includes and variable declarations where appropriate.
* ad7791
- Changes to the AD ADC library used by this driver took in the
sampling frequency. This lead to be the wrong path being the one
tied to the resulting attribute, so it didn't work, and a warning
to be printed.
* ad7780
- Remove apparent support for sampling frequency control on devices
that don't support changing the sampling attributes.
* ade7854
- Fix a read of the wrong number of bits.
- Improve error handling on i2c read/write errors.
- Rework i2c and spi code to reduce duplication.
* adis16201 (staging)
- Improve meaning inherent in some macro names by adding units etc
where relevant.
- Adjust comments to improve detail and drop the irrelevant.
- Rename register address definitions definitions to add a _REG
postfix, clearly separating them from field definitions. Reorganize
the definitions to group register address and fields.
- Use sign_extend32 rather than open coding.
- Reverse Xmas tree ordering where appropriate and align function args.
- Remove unused headers.
- Use GENMASK where appropriate instead of open coding.
* adis16209 (staging)
- Indent field definitions to visually separate them from
register address definitions.
- Use reverse xmas tree ordering where appropriate.
- Add some whitespace where it will help readability.
- Drop some unused headers.
- Use GENMASK where appropriate.
* ad2s1200
- Drop unnecessary includes and reorder alphabetically.
- Reverse xmas tree and blank line cleanups.
* atlas-ph-sensor
- Use msleep instead of usleep_range where the precise value doesn't
matter and the delays are long.
* bcm150
- Drop transaction splitting as core now handles it.
* cros_ec
- Move the shared header to the include/iio/common directory.
This brings it inline with the other multiple type devices.
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* hid-sensors
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* inv_mpu6050
- Clear out a second function definition for the same function.
- Don't flush fifo when the iio buffer is full but just drop excess
data.
- Tidy up set_power_itg and ensure it is used in the right places.
- Use set_power_itg rather than opencoding it again in the i2c mux
control.
- Make sure error paths disable the power if undoing power on.
- Used managed devm_ functions during probe. Delete remove function.
- Refactor to pull raw data read out of read_raw function.
- Simplify data reading error paths.
- Only enable the i2c mux for chips with the i2c aux bus (not icm20608)
- Fix a potential deadlock due to varying lock ordering.
- Fix an issue where first sample from gyro after enabling is unstable
by dropping the first sample.
- Fix an issue where the user_ctrl register is incorrectly overwritten.
- Tidy up some grammar and spelling minor issus.
* mcp320x
- Use vendor compatible strings.
* mcp4018
- Switch to using i2c .probe_new.
* mcp4351
- switch to using i2c .probe_new.
* meson-adc
- rework handing on common ADC platform data so it can be shared
across multiple families of SoCs.
* sca3000
- Fix an error handling path if the ring configure fails.
* st_lsm6dsx
- Fix a wrong fifo threshold mask (no actual effect)
* stm32-dfsdm
- Style fixes and cleanups.
- Check filter ID is in range and check spi-max-frequency.
* tsl2x7x (staging)
- Drop some unnecessary function calls, unused variables and
unnecessary local variables.
- Fix wrong interrupt type.
- Avoid unnecessary double clear of interrupt.
- Simplify proximity calibration call which did various things
unrelated to actually calibrating.
- Separate control of the proximity and ALS interrupts.
- Improve consistency of logging.
- Separate ALS and proximity persistence settings as they have
separate hardware controls.
- Tidy up variable ordering.
- Add Brian to copyright notice given consider work on this driver.
- Take advantage of hardware support for I2C address auto increment.
- Combine individuaal enable and period attributes for the two
directions on the threshold events into a single value as the
hardware doesn't separate them.
- Move integration_time* attributes from light channel to
intensity value as they effect the intensity readings directly
and the light reading only indirectly. Hence this better
reflects reality. Also move the calibscale_available.
- Avoid returning an error in the IRQ handler.
- Hard code the reg value in _clear_interrupts as it only takes
one value in the code. Result is the function has little
purpose so opencode the two remaining i2c_smbus_write_byte
calls.
- Drop some unnecessary checking of the chip status register.
- Tidy up return path in _write_interrupt_config.
- Tidy up the ID verification code.
- Move the power and diode settings defines into the header as these
are needed for platform data configuration.
- Various renames and comment cleanups for consistency and clarity.
- Use actual device defaults for default startup settings.
- SPDX
- Add some range sanity checking to sysfs attribute writes.
- Don't provide event interfaces if the interrupt line isn't available.
- Use IIO_CONST_ATTR macro for calibscale_available as it's a constant
string.
- Fix the integration time and lux equations.
- Make device IDs explicit index values in the device_channel_config array.
-----BEGIN PGP SIGNATURE-----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=egCX
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.18a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
1st round of IIO new device support, features and cleanup for the 4.18 cycle
A nice mix this time of excellent cleanups (many to send drivers
speeding toward staging graduations) and new drivers / device support.
A good part of this is Brian Masney's never ending task on the tsl2x7x
driver. The end is in sight so hopefully we'll get that one out of
staging very soon!
New device support
* AD5686
- Support AD5685R (was wrongly present as AD5685)
- Support AD5672R, AD5676, AD5676, AD5684R and AD5686R 4 and 8 channel
SPI DACs with various precisions.
- Support AD5671R, AD5675R, AD5694, AD5694R, AD5695R, AD5696 and AD5696R
I2C DACs with various percisions and numbers of channels.
* Analog front end rescale driver - New driver.
- Support current sensing usings a shunt resistor.
- Support simple voltage dividers.
- support simple current sense amplifiers.
* TI dac5571
- New driver and device bindings supporting:
dac5571, dac6571, dac7571, dac5574, dac6574, dac7574,
dac5573, dac6573 and dac7573
* Meson-adc
- Support for Meson AXG with DT bindings.
* mpu6050
- Support the mpu9255 which only requires additional WHOAMI entry and
compatible string.
* st_lsm6dsx
- Support for lsm330dlc combinded accelerometer and gyro sensors with
DT bindings.
* stm32_adc
- Add support for STM32MP1 with bindings.
Staging graduations
* adis16201 after some excelent cleanup by Himanshu Jha.
* adis16029 after some excelent cleanup by Shreeya Patel.
New features:
* ABI docs
- Add core ABI docs for angle channels.
* inv_mpu6050
- Provide support for the full range of interrupts the device
supports.
* st_accel
- Add SMO8840 ACPI ID seen in the wild on some Lenovo machines.
* stx104
- Provide a multiple gpio get function.
Cleanups / Minor fixes
* core
- Use new nested structure support to improve kernel-doc.
* ad2s1200
- Use be16_to_cpup instead of opencoding.
* ad5686
- Indentation tidy up.
- Switch to SPDX
- Refactor to allow various numbers of channels.
- Refactor to separate core and SPI specific support, prior to
addition of i2c equivalent devices.
* ad7606
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* ad7746
- Replace opencoded byte swapped i2c calls with _swapped variants.
- White space and line break readability improvements.
- Reorder includes and variable declarations where appropriate.
* ad7791
- Changes to the AD ADC library used by this driver took in the
sampling frequency. This lead to be the wrong path being the one
tied to the resulting attribute, so it didn't work, and a warning
to be printed.
* ad7780
- Remove apparent support for sampling frequency control on devices
that don't support changing the sampling attributes.
* ade7854
- Fix a read of the wrong number of bits.
- Improve error handling on i2c read/write errors.
- Rework i2c and spi code to reduce duplication.
* adis16201 (staging)
- Improve meaning inherent in some macro names by adding units etc
where relevant.
- Adjust comments to improve detail and drop the irrelevant.
- Rename register address definitions definitions to add a _REG
postfix, clearly separating them from field definitions. Reorganize
the definitions to group register address and fields.
- Use sign_extend32 rather than open coding.
- Reverse Xmas tree ordering where appropriate and align function args.
- Remove unused headers.
- Use GENMASK where appropriate instead of open coding.
* adis16209 (staging)
- Indent field definitions to visually separate them from
register address definitions.
- Use reverse xmas tree ordering where appropriate.
- Add some whitespace where it will help readability.
- Drop some unused headers.
- Use GENMASK where appropriate.
* ad2s1200
- Drop unnecessary includes and reorder alphabetically.
- Reverse xmas tree and blank line cleanups.
* atlas-ph-sensor
- Use msleep instead of usleep_range where the precise value doesn't
matter and the delays are long.
* bcm150
- Drop transaction splitting as core now handles it.
* cros_ec
- Move the shared header to the include/iio/common directory.
This brings it inline with the other multiple type devices.
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* hid-sensors
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* inv_mpu6050
- Clear out a second function definition for the same function.
- Don't flush fifo when the iio buffer is full but just drop excess
data.
- Tidy up set_power_itg and ensure it is used in the right places.
- Use set_power_itg rather than opencoding it again in the i2c mux
control.
- Make sure error paths disable the power if undoing power on.
- Used managed devm_ functions during probe. Delete remove function.
- Refactor to pull raw data read out of read_raw function.
- Simplify data reading error paths.
- Only enable the i2c mux for chips with the i2c aux bus (not icm20608)
- Fix a potential deadlock due to varying lock ordering.
- Fix an issue where first sample from gyro after enabling is unstable
by dropping the first sample.
- Fix an issue where the user_ctrl register is incorrectly overwritten.
- Tidy up some grammar and spelling minor issus.
* mcp320x
- Use vendor compatible strings.
* mcp4018
- Switch to using i2c .probe_new.
* mcp4351
- switch to using i2c .probe_new.
* meson-adc
- rework handing on common ADC platform data so it can be shared
across multiple families of SoCs.
* sca3000
- Fix an error handling path if the ring configure fails.
* st_lsm6dsx
- Fix a wrong fifo threshold mask (no actual effect)
* stm32-dfsdm
- Style fixes and cleanups.
- Check filter ID is in range and check spi-max-frequency.
* tsl2x7x (staging)
- Drop some unnecessary function calls, unused variables and
unnecessary local variables.
- Fix wrong interrupt type.
- Avoid unnecessary double clear of interrupt.
- Simplify proximity calibration call which did various things
unrelated to actually calibrating.
- Separate control of the proximity and ALS interrupts.
- Improve consistency of logging.
- Separate ALS and proximity persistence settings as they have
separate hardware controls.
- Tidy up variable ordering.
- Add Brian to copyright notice given consider work on this driver.
- Take advantage of hardware support for I2C address auto increment.
- Combine individuaal enable and period attributes for the two
directions on the threshold events into a single value as the
hardware doesn't separate them.
- Move integration_time* attributes from light channel to
intensity value as they effect the intensity readings directly
and the light reading only indirectly. Hence this better
reflects reality. Also move the calibscale_available.
- Avoid returning an error in the IRQ handler.
- Hard code the reg value in _clear_interrupts as it only takes
one value in the code. Result is the function has little
purpose so opencode the two remaining i2c_smbus_write_byte
calls.
- Drop some unnecessary checking of the chip status register.
- Tidy up return path in _write_interrupt_config.
- Tidy up the ID verification code.
- Move the power and diode settings defines into the header as these
are needed for platform data configuration.
- Various renames and comment cleanups for consistency and clarity.
- Use actual device defaults for default startup settings.
- SPDX
- Add some range sanity checking to sysfs attribute writes.
- Don't provide event interfaces if the interrupt line isn't available.
- Use IIO_CONST_ATTR macro for calibscale_available as it's a constant
string.
- Fix the integration time and lux equations.
- Make device IDs explicit index values in the device_channel_config array.
This patch adds support for the Texas Intruments DAC5571 Family.
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD5694/AD5694R/AD5695R/AD5696/AD5696R are a family of 4 channel DACs
with 12-bit, 14-bit and 16-bit precision respectively. The devices have
either no built-in reference, or built-in 2.5V reference.
The AD5671R/AD5675R are similar, except that they have 8 instead of 4
channels.
These devices are similar to AD5672R/AD5676/AD5676R and
AD5684/AD5684R/AD5684/AD5685R/AD5686/AD5686R, except that they use i2c
instead of spi.
Datasheets:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5671R_5675R.pdfhttp://www.analog.com/media/en/technical-documentation/data-sheets/AD5696R_5695R_5694R.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In this patch restructures the existing ad5686 driver by adding a module
for SPI and a header file, while the baseline module deals with the
chip-logic.
This is a necessary step, as this driver should support in the future
similar devices which differ only in the type of interface used (I2C
instead of SPI).
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver acctually supports the AD5685R device and NOT the AD5685, which
does not exist. Maintain old id entry in case we have devicetrees
out there which are using the wrong name.
More information can be found in the datasheet:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5686_5684.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds a new num_channels attribute as part of the
ad5686_chip_info struct which replaces the AD5686_DAC_CHANNELS define. This
is a necessary step, since this driver should support similar devices which
differ only in the number of channels.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add GPLv2+ SPDX identifier and remove license notice to keep the whole
purpose of using an SPDx id.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch fixes some indentation issues and does not modify the
functionality of the driver.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
New drivers:
- Nintendo Wii GameCube GPIO, known as "Hollywood"
- Raspberry Pi mailbox service GPIO expander
- Spreadtrum main SC9860 SoC and IEC GPIO controllers.
Improvements:
- Implemented .get_multiple() callback for most of the
high-performance industrial GPIO cards for the ISA bus.
- ISA GPIO drivers now select the ISA_BUS_API instead of
depending on it. This is merged with the same pattern
for all the ISA drivers and some other Kconfig cleanups
related to this.
Cleanup:
- Delete the TZ1090 GPIO drivers following the deletion of
this SoC from the ARM tree.
- Move the documentation over to driver-api to conform with
the rest of the kernel documentation build.
- Continue to make the GPIO drivers include only
<linux/gpio/driver.h> and not the too broad <linux/gpio.h>
that we want to get rid of.
- Managed to remove VLA allocation from two drivers pending
more fixes in this area for the next merge window.
- Misc janitorial fixes.
-----BEGIN PGP SIGNATURE-----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=C5t5
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.17 kernel cycle:
New drivers:
- Nintendo Wii GameCube GPIO, known as "Hollywood"
- Raspberry Pi mailbox service GPIO expander
- Spreadtrum main SC9860 SoC and IEC GPIO controllers.
Improvements:
- Implemented .get_multiple() callback for most of the
high-performance industrial GPIO cards for the ISA bus.
- ISA GPIO drivers now select the ISA_BUS_API instead of depending on
it. This is merged with the same pattern for all the ISA drivers
and some other Kconfig cleanups related to this.
Cleanup:
- Delete the TZ1090 GPIO drivers following the deletion of this SoC
from the ARM tree.
- Move the documentation over to driver-api to conform with the rest
of the kernel documentation build.
- Continue to make the GPIO drivers include only
<linux/gpio/driver.h> and not the too broad <linux/gpio.h> that we
want to get rid of.
- Managed to remove VLA allocation from two drivers pending more
fixes in this area for the next merge window.
- Misc janitorial fixes"
* tag 'gpio-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
gpio: Add Spreadtrum PMIC EIC driver support
gpio: Add Spreadtrum EIC driver support
dt-bindings: gpio: Add Spreadtrum EIC controller documentation
gpio: ath79: Fix potential NULL dereference in ath79_gpio_probe()
pinctrl: qcom: Don't allow protected pins to be requested
gpiolib: Support 'gpio-reserved-ranges' property
gpiolib: Change bitmap allocation to kmalloc_array
gpiolib: Extract mask allocation into subroutine
dt-bindings: gpio: Add a gpio-reserved-ranges property
gpio: mockup: fix a potential crash when creating debugfs entries
gpio: pca953x: add compatibility for pcal6524 and pcal9555a
gpio: dwapb: Add support for a bus clock
gpio: Remove VLA from xra1403 driver
gpio: Remove VLA from MAX3191X driver
gpio: ws16c48: Implement get_multiple callback
gpio: gpio-mm: Implement get_multiple callback
gpio: 104-idi-48: Implement get_multiple callback
gpio: 104-dio-48e: Implement get_multiple callback
gpio: pcie-idio-24: Implement get_multiple/set_multiple callbacks
gpio: pci-idio-16: Implement get_multiple callback
...
Usually, functions responsible for reading raw data typically relies on
values from iio_chan_info_enum to correctly identify the type of data to
be read. There is a set of a device driver that uses the magic number 0
instead of IIO_CHAN_INFO_RAW. This patch improves the readability by
replaces the magic number 0 for the appropriate IIO_CHAN_INFO_RAW in six
devices driver in the IIO subsystem.
Signed-off-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ISA_BUS_API Kconfig option enables the compilation of the ISA bus
driver. The ISA bus driver does not perform any hardware interaction,
and is instead just a thin layer of software abstraction to eliminate
boilerplate code common to ISA-style device drivers. Since ISA_BUS_API
has no dependencies and does not jeopardize the integrity of the system
when enabled, drivers should select it when the ISA bus driver
functionality is needed.
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Found with scripts/coccinelle/misc/boolconv.cocci.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd atomisp
cleanups (take the media tree's version).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnFrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymxbwCgtNlBkqD2JJYpLRKvI/C4w1vzZsEAnA2THRkt
g3ioPBqmqC/2DSbldr2o
=/ebw
-----END PGP SIGNATURE-----
Merge tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO updates from Greg KH:
"Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd
atomisp cleanups (take the media tree's version)"
* tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (507 commits)
staging: lustre: add SPDX identifiers to all lustre files
staging: greybus: Remove redundant license text
staging: greybus: add SPDX identifiers to all greybus driver files
staging: ccree: simplify ioread/iowrite
staging: ccree: simplify registers access
staging: ccree: simplify error handling logic
staging: ccree: remove dead code
staging: ccree: handle limiting of DMA masks
staging: ccree: copy IV to DMAable memory
staging: fbtft: remove redundant initialization of buf
staging: sm750fb: Fix parameter mistake in poke32
staging: wilc1000: Fix bssid buffer offset in Txq
staging: fbtft: fb_ssd1331: fix mirrored display
staging: android: Fix checkpatch.pl error
staging: greybus: loopback: convert loopback to use generic async operations
staging: greybus: operation: add private data with get/set accessors
staging: greybus: loopback: Fix iteration count on async path
staging: greybus: loopback: Hold per-connection mutex across operations
staging: greybus/loopback: use ktime_get() for time intervals
staging: fsl-dpaa2/eth: Extra headroom in RX buffers
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The two properties unique to each supported chip, resolution and number
of channels, are currently gleaned from the chip's name.
E.g. dac102s085 is a dual channel 10-bit DAC.
^^^
This was deemed unmaintainable by the subsystem maintainer once the
driver is extended to support further chips, hence it was requested
to add an explicit table for chip-specific information and use an
enum to reference into it.
This adds 17 LoC without any immediate gain, so make the change in a
separate commit which can be reverted if we determine in 10 years that
it was unnecessary.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The DACrrcS085 (rr = 08/10/12, c = 2/4) family of SPI DACs was
inherited by TI when they acquired National Semiconductor in 2011.
This driver was developed for and tested with the DAC082S085 built into
the Revolution Pi by KUNBUS, but should work with any of the other
chips as they share the same programming interface.
There is also a family of I2C DACs with just a single channel called
DACrr1C08x (rr = 08/10/12, x = 1/5). Their programming interface is
very similar and it should be possible to extend the driver for these
chips with moderate effort. Alternatively they could be integrated into
ad5446.c. (The AD5301/AD5311/AD5321 use different power-down modes but
otherwise appear to be comparable.)
Furthermore there is a family of 8-channel DACs called DACrr8S085
(rr = 08/10/12) as well as two 16-bit DACs called DAC161Sxxx
(xxx = 055/997). These are more complicated devices with support for
daisy-chaining and the ability to power down each channel separately.
They could either be handled by a separate driver or integrated into the
present driver with a larger effort.
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch provides an iio device driver for DS4422/DS4424 chips that support
two/four channel 7-bit Sink/Source Current DAC.
Signed-off-by: Ismail H. Kose <Ismail.Kose@maximintegrated.com>
Signed-off-by: Ismail H. Kose <ihkose@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Texas Instruments DAC7512 has the exact same pinout, programming
interface and power-down modes as the Texas Instruments DAC121S101 and
Analog Devices AD5320, which are already supported by the IIO driver
ad5446.c. Remove the duplicate misc driver.
This requires user space to migrate to the standardized IIO sysfs ABI.
(In other words, it needs to change a filename.)
The IIO driver supports the chip's features more fully, e.g. the ability
to power down the output or choose one of the available powerdown modes.
There is an oddity with the misc driver in that it initializes the SPI
slave to SPI_MODE_0, in contradiction to the datasheet which specifies
that data is latched in on the falling edge, implying that SPI_MODE_1
or SPI_MODE_2 must be used. Another oddity is that Kconfig and the
MODULE_DESCRIPTION() claim the chip has 16-bit resolution although it
actually has 12-bit.
Datasheets:
http://www.ti.com/lit/ds/symlink/dac7512.pdfhttp://www.ti.com/lit/ds/symlink/dac121s101.pdfhttp://www.analog.com/media/en/technical-documentation/data-sheets/AD5320.pdf
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Daniel Mack <daniel@zonque.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The equivalent of this is now done via macro magic when
the relevant register call is made. The actual structure
element will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This adds support for STM32F4 Digital-To-Analog converter.
Add compatible configuration data to handle hfsel (not present
in stm32f4).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix error message, there's no 'st,dac-channel' property, but 'reg'
(see https://lkml.org/lkml/2017/4/3/567).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Two entirely new drivers in here plus the usual range of cleanups and features.
New device support
* ad5064
- add ltc2631, ltc2633 and ltc2635 support.
* bma180
- trivial support for bma250e (new id)
* hid-sensor-rotation
- add relative orientation and geometric orientation support.
* isl29028
- add isl29030 support (its effectively the same part from a driver point of
view)
* maxim_thermocouple
- add max31856 id.
* meson-saradc
- add meson8b SoC adc support.
* ti-adc084s021
- new driver and bindings.
* ti-adc108s102
- new driver and bindings.
Staging graduations
* isl29028
Features
* bma180
- ACPI enumeration for BMA250E which is used in various x86 tablets.
* hi8453
- add raw access rather than only events.
* hid-sensor-hub
- Implement batch mode in which we can set a threshold on the amount of time
between data coming from the fifos. This is the first device to do this
rather than use a watershed on the number of samples.
* hts221
- power management support
* lsm6dsx
- add system power management support.
* rpr0521
- sampling frequency read / write
* stm32-trigger
- add support for TRG02 triggers.
* tsl2583
- runtime power management support.
Cleanups
* core
- inkern: fix a double unlock in iio_read_available_channel_raw when raw
value doesn't appear to be raw (error path).
- fixup accidental sizeof pointer in iio_device_add_mask_type.
* docs
- fix an accidental duplicated line in sysfs-bus-iio-meas-spec.
* tools
- use local include/uapi headers to ensure always up to date.
- increase length of allowed trigger names.
* ad9834
- symbolic to octal permissions.
* ade7753
- symbolic to octal permissions.
- fix indentation
* ade7754
- symbolic to octal permissions.
* ade7758
- symbolic to octal permissions.
- ade7854
- symbolic to octal permissions.
* as3935
- move out of storm check to given consistent results for raw and processed
values.
* bmp280
- fix bme280 naming in Kconfig help.
* hi8435
- avoid garbage on event after enable.
- add missing in_voltage_sensing_mode_available to list possible enum options.
- handle the reset gpio with the obvious polarity rather than relying on
DT to provide it correctly.
* hid-sensors
- fix a wrong error path scrubbing of return values.
* hid-sensors-accel
- drop static on a local variable
* hid-sensors-rotation
- Add missing scale and offset property parsing support.
* ina2xx
- Fix a bad use of GENMASK and some typos and whitespace issues.
* isl29018
- only declare the ACPI table when ACPI is enabled.
* isl29028
- fix proximity sleep times.
* lsm6dsx
- replace ifdef CONFIG_PM with __maybe_unused to avoid the complexity of
dealing with the various PM config variables.
* meson-saradc
- mark meson_sar_adc_data static and const.
* rcar-gyroadc
- derive the interface clock speed from the fck clock on the basis they are
the same actual clock.
- drop the now unused if clock from the bindings.
* rpr0521
- disable sensor when marked as such rather than always enabling it.
- poweroff if probe fails and we can talk to device.
- make sure device powered off when it doesn't need to be on.
- use sizeof rather than hardcoded size on value read.
- whitespace fixup.
- reorder channel numbers ready for buffered support which didn't quite
make this pull request.
* st-accel
- fix platform data initialization to allow remove and reprobe.
* st-pressure
- fix platform data initialization to allow remove and reprobe.
* tsl2x7x
- S_IRUGO, S_IWUSR to octal values
- rename driver for consistency with more recent drivers
- drop FSF mailing address
- replace DEVICE_ATTR macros with the shorter DEVICE_ATTR_RW form and
relevant function renames.
* zpa2326
- report an error for consistency with other error paths.
-----BEGIN PGP SIGNATURE-----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=XLVY
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.13a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 4.13 cycle
Two entirely new drivers in here plus the usual range of cleanups and features.
New device support
* ad5064
- add ltc2631, ltc2633 and ltc2635 support.
* bma180
- trivial support for bma250e (new id)
* hid-sensor-rotation
- add relative orientation and geometric orientation support.
* isl29028
- add isl29030 support (its effectively the same part from a driver point of
view)
* maxim_thermocouple
- add max31856 id.
* meson-saradc
- add meson8b SoC adc support.
* ti-adc084s021
- new driver and bindings.
* ti-adc108s102
- new driver and bindings.
Staging graduations
* isl29028
Features
* bma180
- ACPI enumeration for BMA250E which is used in various x86 tablets.
* hi8453
- add raw access rather than only events.
* hid-sensor-hub
- Implement batch mode in which we can set a threshold on the amount of time
between data coming from the fifos. This is the first device to do this
rather than use a watershed on the number of samples.
* hts221
- power management support
* lsm6dsx
- add system power management support.
* rpr0521
- sampling frequency read / write
* stm32-trigger
- add support for TRG02 triggers.
* tsl2583
- runtime power management support.
Cleanups
* core
- inkern: fix a double unlock in iio_read_available_channel_raw when raw
value doesn't appear to be raw (error path).
- fixup accidental sizeof pointer in iio_device_add_mask_type.
* docs
- fix an accidental duplicated line in sysfs-bus-iio-meas-spec.
* tools
- use local include/uapi headers to ensure always up to date.
- increase length of allowed trigger names.
* ad9834
- symbolic to octal permissions.
* ade7753
- symbolic to octal permissions.
- fix indentation
* ade7754
- symbolic to octal permissions.
* ade7758
- symbolic to octal permissions.
- ade7854
- symbolic to octal permissions.
* as3935
- move out of storm check to given consistent results for raw and processed
values.
* bmp280
- fix bme280 naming in Kconfig help.
* hi8435
- avoid garbage on event after enable.
- add missing in_voltage_sensing_mode_available to list possible enum options.
- handle the reset gpio with the obvious polarity rather than relying on
DT to provide it correctly.
* hid-sensors
- fix a wrong error path scrubbing of return values.
* hid-sensors-accel
- drop static on a local variable
* hid-sensors-rotation
- Add missing scale and offset property parsing support.
* ina2xx
- Fix a bad use of GENMASK and some typos and whitespace issues.
* isl29018
- only declare the ACPI table when ACPI is enabled.
* isl29028
- fix proximity sleep times.
* lsm6dsx
- replace ifdef CONFIG_PM with __maybe_unused to avoid the complexity of
dealing with the various PM config variables.
* meson-saradc
- mark meson_sar_adc_data static and const.
* rcar-gyroadc
- derive the interface clock speed from the fck clock on the basis they are
the same actual clock.
- drop the now unused if clock from the bindings.
* rpr0521
- disable sensor when marked as such rather than always enabling it.
- poweroff if probe fails and we can talk to device.
- make sure device powered off when it doesn't need to be on.
- use sizeof rather than hardcoded size on value read.
- whitespace fixup.
- reorder channel numbers ready for buffered support which didn't quite
make this pull request.
* st-accel
- fix platform data initialization to allow remove and reprobe.
* st-pressure
- fix platform data initialization to allow remove and reprobe.
* tsl2x7x
- S_IRUGO, S_IWUSR to octal values
- rename driver for consistency with more recent drivers
- drop FSF mailing address
- replace DEVICE_ATTR macros with the shorter DEVICE_ATTR_RW form and
relevant function renames.
* zpa2326
- report an error for consistency with other error paths.
The Linear Technology LTC2631, LTC2633 and LTC2635 are very similar
to the AD5064 device, in particular the LTC2627.
This patch adds support for those devices. Only the LTC2633 has been
tested, which is the 2-channel variant. The LTC2631 is the 1-channel,
and the LTC2635 the 4-channel version. The actual DAC resolution depends
on the exact chip type and can be 12, 10 or 8 bits, using the upper bits
so this has no effect on the register map. The internal reference is set
to 2.5V on "L" versions, and it's 4.096V for "H" versions.
Datasheets:
LTC2631: http://www.linear.com/docs/26553
LTC2633: http://www.linear.com/docs/39529
LTC2635: http://www.linear.com/docs/28754
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
-----BEGIN PGP SIGNATURE-----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=lbS7
-----END PGP SIGNATURE-----
Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in drivers/iio/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
cc: linux-iio@vger.kernel.org
As these are rather late in the cycle, they may sneak over into 4.12.
There is a fix for a regression caused by another fix (hid sensors
hardware seems to vary a lot in how various corner cases are handled).
* ad7303
- fix channel description. Numeric values were being passed as characters
presumably leading to garbage from the userspace interface.
* as3935
- the write data macro was wrong so fix it.
* bmp280
- incorrect handling of negative values as being unsigned broke humidity
calculation.
* hid-sensor
- Restore the poll and hysteresis values after resume as some hardware
doesn't do it.
* stm32-trigger
- buglet in reading the sampling frequency
-----BEGIN PGP SIGNATURE-----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=H5KS
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.11e' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Fifth set of IIO fixes for the 4.11 cycle.
As these are rather late in the cycle, they may sneak over into 4.12.
There is a fix for a regression caused by another fix (hid sensors
hardware seems to vary a lot in how various corner cases are handled).
* ad7303
- fix channel description. Numeric values were being passed as characters
presumably leading to garbage from the userspace interface.
* as3935
- the write data macro was wrong so fix it.
* bmp280
- incorrect handling of negative values as being unsigned broke humidity
calculation.
* hid-sensor
- Restore the poll and hysteresis values after resume as some hardware
doesn't do it.
* stm32-trigger
- buglet in reading the sampling frequency
Add support for STMicroelectronics STM32 DAC. It's a 12-bit, voltage
output digital-to-analog converter. It has two output channels, each
with its own converter.
It supports 8 bits or 12bits left/right aligned data format. Only
12bits right-aligned is used here. It has built-in noise or
triangle waveform generator, and supports external triggers for
conversions.
Each channel can be used independently, with separate trigger, then
separate IIO devices are used to handle this. Core driver is intended
to share common resources such as clock, reset, reference voltage and
registers.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
realbits, storagebits and shift should be numbers, not ASCII characters.
Signed-off-by: Pavel Roskin <plroskin@gmail.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The following Coccinelle script was used to detect this:
@r@
expression x;
void* e;
type T;
identifier f;
@@
(
*((T *)e)
|
((T *)x)[...]
|
((T*)x)->f
|
- (T*)
e
)
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Check for attribute_group structures that are only stored in the
event_attrs filed of iio_info structure. As the event_attrs field of
iio_info structures is constant, so these attribute_group structures can
also be declared constant. Done using coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct attribute_group i@p = {...};
@ok1@
identifier r1.i;
position p;
struct iio_info x;
@@
x.event_attrs=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct attribute_group i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct attribute_group i;
File size before:
text data bss dec hex filename
3046 360 0 3406 d4e drivers/iio/dac/ad5504.o
File size after:
text data bss dec hex filename
3110 296 0 3406 d4e drivers/iio/dac/ad5504.o
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for Linear Technology LTC2632 (SPI) family of·
dual 12- 10-, and 8-bits output DACs.
Signed-off-by: Maxime Roussin-Belanger <maxime.roussinbelanger@gmail.com>
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver has a OF device ID table but the struct i2c_driver
.of_match_table field is not set.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Initialize the parent of the IIO device to the device that registered it.
This makes sure that the IIO device appears the right level in the device
hierarchy.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds the ACPI/PNP ID. The AD5592/3 driver core is already
designed around the unified device property API.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds the ACPI/PNP ID. The AD5592/3 driver core is already
designed around the unified device property API.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
It is assumed that the dpot is used as a voltage divider between the
current dpot wiper setting and the maximum resistance of the dpot. The
divided voltage is provided by a vref regulator.
.------.
.-----------. | |
| vref |--' .---.
| regulator |--. | |
'-----------' | | d |
| | p |
| | o | wiper
| | t |<---------+
| | |
| '---' dac output voltage
| |
'------+------------+
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
PTR_ERR should access the value just tested by IS_ERR
Generated by: scripts/coccinelle/tests/odd_ptr_err.cocci
CC: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
MCP47x6 chip supports selection of a voltage reference (VDD, VREF buffered
or unbuffered). MCP4725 doesn't have this feature thus the eventual setting
is ignored and user is warned.
The setting is stored only in the volatile memory of the chip. You need to
manually store it to the EEPROM of the chip via 'store_eeprom' sysfs entry.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Number 2 is referencing to the settings with the largest available
resistor.
No functional change.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Kees Cook
Silvan Murer
Stefan Popa
Greg Kroah-Hartman
Sean Nyekjaer
Linus Torvalds
Rodrigo Siqueira
William Breathitt Gray
Andrew F. Davis
Benjamin Gaignard
Lukas Wunner
Ismail H. Kose
Jonathan Cameron
Philipp Zabel
Fabrice Gasnier
Mike Looijmans
David Howells
Pavel Roskin
simran singhal
Maxime Roussin-Belanger
Javier Martinez Canillas
Lars-Peter Clausen
Michael Hennerich
Peter Rosin
Julia Lawall
Tomas Novotny