The channel argument is not used and anyway it could be retrieved from
the passed driver data structure.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The tgl_spi pointer is now unused so remove it.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The change updates sh_msiof_spi_set_clk_regs() function by iterating
over BRDV power values. Note that the change is a functional one, namely
prescaler output x 1/1 set in BRDV bit field (0b111) for MSO division
rate set to 2 is substituted by BRDV = 0b000 and BRPS = 0b0, in terms
of written values to TSCR setting of 0x0107 is substituted by 0x0000,
and for all input parameter cases this is the only functional change,
which touches the controller.
As a result of the rework the function is supposed to be slightly more
efficient and more readable and maintainable in case of any further
extensions.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
clk_get_rate() is below clk_prepare_enable(), so
its error should lead to goto err_clk_disable, not to err_master_put.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The change fixes a bit field overflow which allows to write to higher
bits while calculating SPI transfer clock and setting BRPS and BRDV
bit fields, the problem is reproduced if 'parent_rate' to 'spi_hz'
ratio is greater than 1024, for instance
p->min_div = 2,
MSO rate = 33333333,
SPI device rate = 10000
results in
k = 5, i.e. BRDV = 0b100 or 1/32 prescaler output,
BRPS = 105,
TSCR value = 0x6804, thus MSSEL and MSIMM bit fields are non-zero.
Fixes: 65d5665bb2 ("spi: sh-msiof: Update calculation of frequency dividing")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now i.MX SPI controller can work in Slave mode.
Update MODULE_DESCRIPTION to "SPI Controller driver".
Signed-off-by: wangbo <wang.bo116@zte.com.cn>
Signed-off-by: Mark Brown <broonie@kernel.org>
A quiet release for SPI, some fixes and small updates for individual
drivers with one bigger change from Linus Walleij which coverts the
bitbanging SPI driver to use the GPIO descriptor API from Linus Walleij.
Since GPIO descriptors were used by platform data this means there's a
few changes in arch/ making relevant updates for a few platforms and one
misc driver that are affected.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlrCYDYTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DXhB/9Hueo2D1Pku0iAwq+yIAPvk2N0fyGP
YWJWbDQGngSZEnU3dUzdfaOHh4MMiMgs0q8hxOYnmkIhhTs7cXsPj8x6rlZP8bee
TtSEEgHSuHlVWyADquFIel8OCq8BWd7p4aQKqP3LaojCH/wqswxtn4I+RH/xw1Rd
LIPgU12fxGUpRMO7uGNiMhqqkQDH1ZBFzCUYRPqQk2E+5hyZraQYoROgZkEBPzb1
EWjLxLxytj/Zj4N5eQkW4BWfX5HKJb9CpwKIIdyNuybr14yC5FR83VxOf9wW4/pG
39DIn8LtGTkuMRF4Yw5rPlC9KqnLpUDTnQCcOW4lt+z8QtZQ+LP3boxE
=xNln
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull SPI updates from Mark Brown:
"A quiet release for SPI, some fixes and small updates for individual
drivers with one bigger change from Linus Walleij which coverts the
bitbanging SPI driver to use the GPIO descriptor API from Linus
Walleij.
Since GPIO descriptors were used by platform data this means there's a
few changes in arch/ making relevant updates for a few platforms and
one misc driver that are affected"
* tag 'spi-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (24 commits)
MAINTAINERS: update Andi's e-mail
spi: spi-atmel: Use correct enum for DMA transfer direction
spi: sh-msiof: Document R-Car M3-N support
spi: sh-msiof: Use correct enum for DMA transfer direction
spi: sprd: Add the support of restarting the system
spi: sprd: Simplify the transfer function
spi: Fix unregistration of controller with fixed SPI bus number
spi: rspi: use correct enum for DMA transfer direction
spi: jcore: disable ref_clk after getting its rate
spi: bcm-qspi: fIX some error handling paths
spi: pxa2xx: Disable runtime PM if controller registration fails
spi: tegra20-slink: use true and false for boolean values
spi: Fix scatterlist elements size in spi_map_buf
spi: atmel: init FIFOs before spi enable
spi: orion: Prepare space for per-child options
spi: orion: Make the error message greppable
spi: orion: Rework GPIO CS handling
spi: bcm2835aux: Avoid 64-bit arithmetic in xfer len calc
spi: spi-gpio: Augment device tree bindings
spi: spi-gpio: Rewrite to use GPIO descriptors
...
Use enum dma_transfer_direction as required by the functions
dmaengine_prep_slave_(sg|single)() instead of enum dma_data_direction.
This won't change behavior in practice as the enum values are
equivalent.
This fixes two warnings when building with clang:
drivers/spi/spi-atmel.c:771:12: warning: implicit conversion from enumeration
type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction'
[-Wenum-conversion]
DMA_FROM_DEVICE,
^~~~~~~~~~~~~~~
...
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The blackfin architecture is getting removed, so these
won't be needed any more.
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Aaron Wu <aaron.wu@analog.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A lot of Kconfig symbols have architecture specific dependencies.
In those cases that depend on architectures we have already removed,
they can be omitted.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use enum dma_transfer_direction as required by dmaengine_prep_slave_sg()
instead of enum dma_data_direction. This won't change behavior in
practice as the enum values are equivalent.
This fixes two warnings when building with clang:
drivers/spi/spi-sh-msiof.c:755:27: warning: implicit conversion from enumeration
type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
rx->sgl, rx->nents, DMA_FROM_DEVICE,
^~~~~~~~~~~~~~~
drivers/spi/spi-sh-msiof.c:772:27: warning: implicit conversion from enumeration
type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
tx->sgl, tx->nents, DMA_TO_DEVICE,
^~~~~~~~~~~~~
Based on commit 768d59f5d0 ("spi: rspi: use correct enum for DMA
transfer direction").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Spreadtrum platform, we use one PMIC watchdog to reset the whole system
with loading one suitable timeout value (usually 50ms) for the watchdog.
In theory, we should implement the restart function in drivers/power/reset
subsystem to access the PMIC watchdog with regmap. When restart the system,
other cores will be stopped by IPI, but if other cores were accessing PMIC
with holding the regmap mutex lock, that will cause dead-lock issue if we
try to access the PMIC watchdog with regmap to restart the whole system.
Thus we can implement the restart function in ADI driver to avoid this
issue.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We can move the hardware spinlock protection into the ADI read/write
functions to simplify the sprd_adi_transfer_one() function. Moreover
this optimization can also help to access PMIC without considering
the hardware spinlock using sprd_adi_read/write() functions.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 9b61e30221 (spi: Pick spi bus number from Linux idr or spi alias)
ceased to unregister SPI buses with fixed bus numbers. Moreover this is
visible only if CONFIG_SPI_DEBUG=y is set or when trying to re-register
the same SPI controller.
rmmod spi_pxa2xx_platform (with CONFIG_SPI_DEBUG=y):
[ 26.788362] spi_master spi1: attempting to delete unregistered controller [spi1]
modprobe spi_pxa2xx_platform:
[ 37.883137] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:19.0/pxa2xx-spi.12/spi_master/spi1'
[ 37.894984] CPU: 1 PID: 1467 Comm: modprobe Not tainted 4.16.0-rc4+ #21
[ 37.902384] Call Trace:
...
[ 38.122680] kobject_add_internal failed for spi1 with -EEXIST, don't try to register things with the same name in the same directory.
[ 38.136154] WARNING: CPU: 1 PID: 1467 at lib/kobject.c:238 kobject_add_internal+0x2a5/0x2f0
...
[ 38.513817] pxa2xx-spi pxa2xx-spi.12: problem registering spi master
[ 38.521036] pxa2xx-spi: probe of pxa2xx-spi.12 failed with error -17
Fix this by not returning immediately from spi_unregister_controller() if
idr_find() doesn't find controller with given ID/bus number. It finds
only those controllers that were registered with dynamic SPI bus
numbers. Only conditional cleanup between dynamic and fixed bus numbers
is to remove allocated IDR.
Fixes: 9b61e30221 (spi: Pick spi bus number from Linux idr or spi alias)
Cc: stable@vger.kernel.org
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use enum dma_transfer_direction as required by dmaengine_prep_slave_sg
instead of enum dma_data_direction. This won't change behavior in
practice as the enum values are equivalent.
This fixes two warnings when building with clang:
drivers/spi/spi-rspi.c:538:26: warning: implicit conversion from enumeration
type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
rx->sgl, rx->nents, DMA_FROM_DEVICE,
^~~~~~~~~~~~~~~
drivers/spi/spi-rspi.c:558:26: warning: implicit conversion from enumeration
type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
tx->sgl, tx->nents, DMA_TO_DEVICE,
^~~~~~~~~~~~~
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver does not disable ref_clk on remove.
According to the comment, the only reason to enable the clock is to get
its rate. So, it should be safe to disable clk just after that.
By the way, clk_prepare_enable() looks to be more appropriate
than clk_enable() here.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason, commit c0368e4db4 ("spi: bcm-qspi: Fix use after free
in bcm_qspi_probe() in error path") has updated some gotos, but not all of
them.
This looks spurious, so fix it.
Fixes: fa236a7ef2 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't leave runtime PM enabled in case devm_spi_register_controller()
returns with an error. Otherwise runtime PM will complain when driver is
reloaded:
[ 693.855811] pxa2xx-spi pxa2xx-spi.13: Unbalanced pm_runtime_enable!
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When SPI transfers can be offloaded using DMA, the SPI core need to
build a scatterlist to make sure that the buffer to be transferred is
dma-able.
This patch fixes the scatterlist entry size computation in the case
where the maximum acceptable scatterlist entry supported by the DMA
controller is less than PAGE_SIZE, when the buffer is vmalloced.
For each entry, the actual size is given by the minimum between the
desc_len (which is the max buffer size supported by the DMA controller)
and the remaining buffer length until we cross a page boundary.
Fixes: 65598c13fd ("spi: Fix per-page mapping of unaligned vmalloc-ed buffer")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The datasheet recommends initializing FIFOs before
SPI enable. If we do not do it like this, there may be
a strange behavior. We noticed that DMA does not work properly
with FIFOs if we do not clear them beforehand or enable them
before SPIEN.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Aggregating all options for a particular child underneath a common
struct looks cleaner compared to having a separate array for each
per-child option.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 544248623b introduced a new user-visible string which was
however split into two chunks. Thanks to Mark Brown for noticing.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Claim the GPIO from the driver, not via DT bindings or through the
platform code
- Find an unused HW CS signal because Orion needs to drive one for each
SPI transaction
The spi-orion.c was the only driver which supported (or cared about) the
CS GPIO, while it wasn't actually requesting it. This change means that
the DT bindings should stop hogging the GPIO CS pins because it's now
being handled by the driver.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
We want to check for xfers that are over 30 microseconds. Rather than
find how many µs a xfer will take, instead find how many bytes can be
transferred in 30 µs. The latter must be less than 32 bits (since our
clock speed is limited to 32 bits), while the former involves 64 bit
quantities and more arithmetic operations.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the bit-banged GPIO SPI driver to looking up and
using GPIO descriptors to get a handle on GPIO lines for SCK,
MOSI, MISO and all CS lines.
All existing board files are converted in one go to keep it all
consistent. With these conversions I rarely find any interrim
steps that makes any sense.
Device tree probing and GPIO handling should work like before
also after this patch.
For board files, we stop using controller data to pass the GPIO
line for chip select, instead we pass this as a GPIO descriptor
lookup like everything else.
In some s3c24xx machines the names of the SPI devices were set to
"spi-gpio" rather than "spi_gpio" which can never have worked, I
fixed it working (I guess) as part of this patch set. Sometimes
I wonder how this code got upstream in the first place, it
obviously is not tested.
mach-s3c64xx/mach-smartq.c has the same problem and additionally
defines the *same* GPIO line for MOSI and MISO which is not going
to be accepted by gpiolib. As the lines were number 1,2,2 I assumed
it was a typo and use lines 1,2,3. A comment gives awat that line 0
is chip select though no actual SPI device is provided for the LCD
supposed to be on this bit-banged SPI bus. I left it intact instead
of just deleting the bus though.
Kill off board file code that try to initialize the SPI lines
to the same values that they will later be set by the spi_gpio
driver anyways. Given the huge number of weird things in these
board files I do not think this code is very tested or put in
with much afterthought anyways.
In order to assert that we do not get performance regressions on
this crucial bing-banged driver, a ran a script like this dumping the
Ilitek ILI9322 regmap 10000 times (it has no caching obviously) on
an otherwise idle system in two iterations before and after the
patches:
#!/bin/sh
for run in `seq 10000`
do
cat /debug/regmap/spi0.0/registers > /dev/null
done
Before the patch:
time test.sh
real 3m 41.03s
user 0m 29.41s
sys 3m 7.22s
time test.sh
real 3m 44.24s
user 0m 32.31s
sys 3m 7.60s
After the patch:
time test.sh
real 3m 41.32s
user 0m 28.92s
sys 3m 8.08s
time test.sh
real 3m 39.92s
user 0m 30.20s
sys 3m 5.56s
So any performance differences seems to be in the error margin.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert to generalized SPI controller API introduced by the
commit 8caab75fd2 ("spi: Generalize SPI "master" to "controller"").
Inside driver variable name "master" is still used to indicate the driver
is master only.
While at it, change "unsigned cs" to "unsigned int cs" in
pxa2xx_spi_fw_translate_cs() to suppress checkpatch warning.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert to generalized SPI controller API introduced by the
commit 8caab75fd2 ("spi: Generalize SPI "master" to "controller"").
Inside driver variable name "master" is still used to indicate the driver
is master only.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AVR32 symbol was removed in commit 26202873bb ("avr32: remove
support for AVR32 architecture").
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move SSP idle waiting before CS deassert from error and end of message
handling function giveback() to cs_deassert(). This ensures idle waiting
is done also if there is CS change between transfers.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Local struct chip_data has two members that are not used:
- cs. Looks like was never used
- enable_dma. Became unused by the commit f89a6d8f43 ("spi: dw-mid: move
to use core SPI DMA mappings").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the optional "axi" clk is deferred, we still need to undo some
initialisation. Especially 'master' must be released. It will be
reallocated the next time 'orion_spi_probe()' is called.
Add a new label to clean what needs to be cleaned and rename another
label to improve the names used.
Fixes: 92ae112e47 ("spi: orion: Fix clock resource by adding an optional bus clock")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warnings :
line 767: warning: incorrect type in assignment (different base types)
line 767: expected unsigned int [unsigned] [assigned] [usertype] val_out
line 767: got restricted __le32 [usertype] <noident>
line 776: warning: cast to restricted __le32
This takes advantage of readl/writel to do the endianness reordering,
and removes an extra variable in the function.
Fixes: f68a7dcb91 ("spi: a3700: Add full-duplex support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@smile.fr>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warnings :
line 504: warning: incorrect type in assignment (different base types)
line 504: expected unsigned int [unsigned] [usertype] val
line 504: got restricted __le32 [usertype] <noident>
line 527: warning: cast to restricted __le32
This is solved by removing endian-converson functions, since the
converted values are going through readl/writel anyway, which take care
of the conversion.
Fixes: 6fd6fd68c9 ("spi: armada-3700: Fix padding when sending not 4-byte aligned data")
Signed-off-by: Maxime Chevallier <maxime.chevallier@smile.fr>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The armada 3700 SPI controller has support for full-duplex transfers,
but it can only be done without using the hardware FIFOs.
A full duplex transfer is done by shifting 4 bytes at a time, or even
one byte at a time for transfers less than 4 bytes long.
While this method is perfectly suitable for small transfers, it is still
slower than using the FIFOs.
This commit implement full-duplex support, making sure that half-duplex
transfers are still done using the FIFOs with the existing method.
Some setup functions were moved around to make sure the controller is
properly configured before beginning each transfer.
This was tested on EspressoBin with a logical analyser, and a simple
setup where MISO is connected on MOSI. Transfers were made from
userspace using spidev and spi-pipe from the spi-tools project
Signed-off-by: Maxime Chevallier <maxime.chevallier@smile.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
The armada 3700 SPI controller allows to make transfers without using
the 32 bytes RFIFO and WFIFO.
This commit enable switching between FIFO and non-FIFO mode, which is
necessary to implement full-duplex transfers.
Signed-off-by: Maxime Chevallier <maxime.chevallier@smile.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Armada 3700 SPI controller has an internal clock divider which can
divide the parent clock frequency by up to 30.
This patch sets the limits in the spi_controller fields so that we can
detect when a non-supported frequency is requested by a device for a
transfer.
Signed-off-by: Maxime Chevallier <maxime.chevallier@smile.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
When performing a read using FIFO mode, the spi controller shifts out
the last 2 bytes that were written in a previous transfer on MOSI.
This undocumented behaviour can cause devices to misinterpret the
transfer, so we explicitly clear the WFIFO before each read.
This behaviour was noticed on EspressoBin.
Signed-off-by: Maxime Chevallier <maxime.chevallier@smile.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Armada 7K/8K we need to explicitly enable the bus clock. The bus clock
is optional because not all the SoCs need them but at least for Armada
7K/8K it is actually mandatory.
The binding documentation is updating accordingly as well as mentioning
the mandatory clock which was also missing.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the original license statement with the SPDX identifier.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since clocks are disabled except during message transfer clocks
are also disabled when spi_imx_remove gets called. Accessing
registers leads to a freeeze at least on a i.MX 6ULL. Enable
clocks before disabling accessing the MXC_CSPICTRL register.
Fixes: 9e556dcc55 ("spi: spi-imx: only enable the clocks when we start to transfer a message")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch enables SPI DMA transfers for Atmel SAM9 SoCs and implements a
bounce buffer for transfers which have vmalloc allocated buffers. Those
buffers are not cache coherent even if they have been transformed into sg
lists. UBIFS is affected by this cache coherency issue.
In this patch I also reverted "spi: atmel: fix corrupted data issue on SAM9
family SoCs"(7094576ccd).
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using RX (with or without TX), the DMA interrupt triggers
completion when the RX FIFO has been emptied, i.e. after the full
transfer has finished.
However, when using TX without RX, the DMA interrupt triggers completion
as soon as the DMA engine has filled the TX FIFO, i.e. before the full
transfer has finished. Then sh_msiof_modify_ctr_wait() will spin until
the transfer has really finished and the TFSE bit is cleared, for at
most 1 ms. For slow speeds and/or large transfers, this may cause
timeouts and transfer failures:
spi_sh_msiof e6e10000.spi: failed to shut down hardware
74x164 spi2.0: SPI transfer failed: -110
spi_master spi2: failed to transfer one message from queue
74x164 spi2.0: Failed writing: -110
Fix this by waiting explicitly until the TX FIFO has been emptied.
Based on a patch in the BSP by Hiromitsu Yamasaki.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver creates a number of const structures that it stores in the
data field of an of_device_id array.
The data field of an of_device_id structure has type const void *, so
there is no need for a const-discarding cast when putting const values
into such a structure.
Done using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit makes transfer function use spi_transfer_is_last to
determine if currently processed transfer is the last one. Thanks to
that we finally set hardware registers properly and it makes controller
behave the way it's expected to.
This allows simplifying read function which can now simply start reading
from the slot 0 instead of the last saved offset. It has been
successfully tested using spi_write_then_read.
Moreover this change fixes handling messages with two writing transfers.
It's important for SPI flash devices as their drivers commonly use one
transfer for a command and another one for data.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver creates various const structures that it stores in the
data field of an of_device_id array.
Adding const to the declaration of the location that receives the
const value from the data field ensures that the compiler will
continue to check that the value is not modified. Furthermore, the
const-discarding cast on the extraction from the data field is no
longer needed.
Done using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
gpiod_free() is an internal function for gpiolib, gpiod_put() is the
correct external function.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
gpio_free(gpio) simply does gpiod_free(gpio_to_desc(gpio)), so it's
simpler and cleaner to use gpiod_free directly.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The only part of atmel_spi_remove which needs to be atomic is hardware
reset.
atmel_spi_stop_dma calls dma_terminate_all and this needs interrupts
enabled.
atmel_spi_release_dma calls dma_release_channel and dma_release_channel
locks a mutex inside of spin_lock.
So the call of these functions can't be inside a spin_lock.
Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current support for GPIO chip selects assumes the GPIOs have been
configured by platform code or the boot loader. This includes pinmux
setup and GPIO direction. Hence it does not work as expected when just
described in DT using the "cs-gpios" property.
Fix this by:
1. using devm_gpiod_get_index() to request the GPIO, and thus
configure pinmux, if needed,
2. configuring the GPIO direction is the spi_master.setup() callback.
Use gpio_is_valid() instead of a check on positive numbers.
Note that when using GPIO chip selects, at least one native chip select
must be left unused, as that native chip select will be driven anyway,
and (global) native chip select polarity must be taken into account.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently only the MSIOF_SYNC signal can be used as a native chip
select. Extend support to up to 3 native chipselects using the
MSIOF_SS1 and MSIOF_SS2 signals.
Inspired by a patch in the BSP by Hiromitsu Yamasaki.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi_master.setup() callback must not change configuration registers,
as that could corrupt I/O that is in progress for other SPI slaves.
The only exception is the configuration of the native chip select
polarity in SPI master mode, as a wrong chip select polarity will cause
havoc during all future transfers to any other SPI slave.
Hence stop writing to registers in sh_msiof_spi_setup(), unless it is
the first call for a controller using a native chip select, or unless
native chip select polarity has changed (note that you'll loose anyway
if I/O is in progress). Even then, only do what is strictly necessary,
instead of calling sh_msiof_spi_set_pin_regs().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
When probe function fails in registering the spi controller, the clock
should remain disabled.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Takuo Koguchi <takuo.koguchi.sw@hitachi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On SOC with multiple cpu (like omal l138) it is possible that spi
periferic is already initialized when this module is loaded and so
it is possible to recieve interrupt when the modules is not fully
initialized.
this patch initialize dspi->done before refister the interrupt
handler that use it
Signed-off-by: Michele Dionisio <michele.dionisio@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sun6i_spi_probe() uses sun6i_spi_runtime_resume() to prepare/enable
clocks, so sun6i_spi_remove() should use sun6i_spi_runtime_suspend() to
disable/unprepare them if we're not suspended.
Replacing pm_runtime_disable() by pm_runtime_force_suspend() will ensure
that sun6i_spi_runtime_suspend() is called if needed.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 3558fe900e (spi: sunxi: Add Allwinner A31 SPI controller driver)
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
mclk and hclk need to be disabled. Since pm_runtime_disable does
not disable the clocks, use pm_runtime_force_suspend instead.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Takuo Koguchi <takuo.koguchi.sw@hitachi.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The R-Car Gen2 Hardware User Manual Rev. 2.00 states:
If the master/slave mode select bit (MSTR) is modified while the SPI
function enable bit (SPE) is set to 1 (that is, this module is
enabled), the subsequent operation cannot be guaranteed.
Hence do not set SPCR_SPE when setting SPCR_MSTR, just like the
.set_config_register() implementations for other RSPI variants do.
Note that when booted from QSPI, the boot loader will have set SPCR_MSTR
already, hence usually the bit is never modified by the Linux driver.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the helper introduced by commit e135303bd5 ("device: Add
dev_<level>_once variants") instead of open-coding the same
functionality.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add new compatible string to support SPICC controller which
found at Amlogic Meson-AXG SoC. This is aiming at adding
a couple of enhanced feature patches.
Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Armada 3700 SPI controller has 2 ranges of prescaler coefficients.
One ranging from 0 to 15 by steps of 1, and one ranging from 0 to 30 by
steps of 2.
This commit fixes the prescaler coefficients that are over 15 so that it
uses the correct range of values. The prescaling coefficient is rounded
to the upper value if it is odd.
This was tested on Espressobin with spidev and a locigal analyser.
Signed-off-by: Maxime Chevallier <maxime.chevallier@smile.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
When the core is configured in C_SPI_MODE > 0, it integrates a
lookup table that automatically configures the core in dual or quad mode
based on the command (first byte on the tx fifo).
Unfortunately, that list mode_?_memoy_*.mif does not contain all the
supported commands by the flash.
Since 4.14 spi-nor automatically tries to probe the flash using SFDP
(command 0x5a), and that command is not part of the list_mode table.
Whit the right combination of C_SPI_MODE and C_SPI_MEMORY this leads
into a stall that can only be recovered with a soft rest.
This patch detects this kind of stall and returns -EIO to the caller on
those commands. spi-nor can handle this error properly:
m25p80 spi0.0: Detected stall. Check C_SPI_MODE and C_SPI_MEMORY. 0x21 0x2404
m25p80 spi0.0: SPI transfer failed: -5
spi_master spi0: failed to transfer one message from queue
m25p80 spi0.0: s25sl064p (8192 Kbytes)
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The driver as well as the controller support the SPI lsb first
mode. However, it's not possible to configure it e.g. when using
spidev. Adding this flag to mode_bits resolves the issue and lsb first
mode can be used.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the array is not present, assume all chip selects are native. This
is the standard behavior for SPI masters configured via the device
tree and the behavior of this driver as well when it is configured via
device tree.
This reduces platform data vs DT differences and allows most of the
platform data based boards to remove their chip select arrays.
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Mark Brown <broonie@kernel.org>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the code that requests any chip select GPIOs fails, the cleanup of
spi_bitbang_start() by calling spi_bitbang_stop() is not done. Add this
to the failure path.
Note that spi_bitbang_start() has to be called before requesting GPIOs
because the GPIO data in the spi master is populated when the master is
registed, and that doesn't happen until spi_bitbang_start() is called.
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Mark Brown <broonie@kernel.org>
CC: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver will fail to load if no gpio chip selects are specified,
this patch changes this so that it no longer fails.
It's possible to use all native chip selects, in which case there is
no reason to have a gpio chip select array. This is what happens if
the *optional* device tree property "cs-gpios" is omitted.
The spi core already checks for the absence of gpio chip selects in
the master and assigns any slaves the gpio_cs value of -ENOENT.
Also have the driver respect the standard SPI device tree property "num-cs"
to allow setting the number of chip selects without using cs-gpios.
CC: Mark Brown <broonie@kernel.org>
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit 974488e4ce ("spi: imx: Fix failure path leak on GPIO request
error"), spi_bitbang_start() was moved later in the probe sequence. But
this doesn't work, as spi_bitbang_start() has to be called before
requesting GPIOs because the GPIO data in the spi master is populated when
the master is registed, and that doesn't happen until spi_bitbang_start()
is called. The default only works if one uses one CS.
So add a failure path call to spi_bitbang_stop() to fix the leak.
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Mark Brown <broonie@kernel.org>
CC: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pointer dev is assigned but never read, hence it is redundant
and can be removed. Cleans up clang warning:
drivers/spi/spi-sh-msiof.c:1198:2: warning: Value stored to 'dev'
is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pointer sci is assigned but never read, hence it is redundant
and can be removed. Cleans up clang warning:
drivers/spi/spi-s3c64xx.c:791:2: warning: Value stored to 'sci' is
never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On systems where some controllers get a dynamic ID assigned and some have
a fixed number from DT, the current implemention might run into an IDR
collision if the dynamic controllers gets probed first and get an IDR number,
which is later requested by the controller with the fixed numbering. When
this happens the fixed controller will fail to register with the SPI core.
Fix this by skipping all known alias numbers when assigning the dynamic IDs.
Fixes: 9b61e30221 (spi: Pick spi bus number from Linux idr or spi alias)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
The assignment of status to zero is never read, status is either
updated in the next iteration of the of the loop or several
lines after the end of the loop. Remove it, cleans up clang warning:
drivers/spi/spi-orion.c:674:4: warning: Value stored to 'status'
is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMA supports 32-bit words only,
even if BITLEN1 of SITMDR2 register is 16bit.
Fixes: b0d0ce8b6b ("spi: sh-msiof: Add DMA support")
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the code that requests any chip select GPIOs fails, the cleanup of
spi_bitbang_start() by calling spi_bitbang_stop() is not done.
Fix this by moving spi_bitbang_start() to after the code that requets
GPIOs. The GPIOs are dev managed and don't need explicit cleanup.
Since spi_bitbang_start() is now the last operation, it doesn't need
to be cleaned up in the failure path.
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Mark Brown <broonie@kernel.org>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Take an extra reference to the controller before deregistering it to
prevent use-after-free in the interrupt handler in case an interrupt
fires before the line is disabled.
Fixes: b1353d1c1d ("spi: Add Analog Devices AXI SPI Engine controller support")
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document the fact that a reference to the controller is dropped as part
of deregistration.
This is an odd pattern as the reference is typically taken in
__spi_alloc_controller() rather than spi_register_controller(). Most
controller drivers gets it right these days and notably the
device-managed interface relies on this behaviour.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The controller is typically freed as part of device_unregister() so
store the bus id before deregistration to avoid use-after-free when the
id is later released.
Fixes: 9b61e30221 ("spi: Pick spi bus number from Linux idr or spi alias")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable <stable@vger.kernel.org>
When enabling the ADI hardware channels, if the channel id is 31,
then we will get one negative value -1 for BIT() macro, which will
write incorrect value to register.
Fixes: 7e2903cb91 ("spi: Add ADI driver for Spreadtrum platform")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On systems where some controllers get a dynamic ID assigned and some have
a fixed number from DT, the current implemention might run into an IDR
collision if the dynamic controllers gets probed first and get an IDR number,
which is later requested by the controller with the fixed numbering. When
this happens the fixed controller will fail to register with the SPI core.
Fix this by skipping all known alias numbers when assigning the dynamic IDs.
Fixes: 9b61e30221 (spi: Pick spi bus number from Linux idr or spi alias)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/spi/spi-sprd-adi.c:409:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Fixes: 7e2903cb91 ("spi: Add ADI driver for Spreadtrum platform")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There was an inversion in how the error path in bcm_qspi_probe() is done
which would make us trip over a KASAN use-after-free report. Turns out
that qspi->dev_ids does not get allocated until later in the probe
process. Fix this by introducing a new lable: qspi_resource_err which
takes care of cleaning up the SPI master instance.
Fixes: fa236a7ef2 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Sylwester Nawrocki
Naga Sureshkumar Relli
Vladimir Zapolskiy
Alexey Khoroshilov
wangbo
Linus Torvalds
Mark Brown
Stefan Agner
Arnd Bergmann
Geert Uytterhoeven
Baolin Wang
Jarkko Nikula
Christophe Jaillet
Gustavo A. R. Silva
Maxime Chevallier
Eugen Hristev
Jan Kundrát
Trent Piepho
Linus Walleij
Ulf Magnusson
Maxime Chevallier
Gregory CLEMENT
Andi Shyti
Radu Pirea
Julia Lawall
Rafał Miłecki
Rasmus Villemoes
Takuo Koguchi
Michele Dionisio
Tobias Jordan
Sunny Luo
Ricardo Ribalda
Kurt Kanzenbach
Colin Ian King
Angelo Dureghello
Lucas Stach
Hiromitsu Yamasaki
Greg Kroah-Hartman
Johan Hovold
Wu Fengguang
Florian Fainelli