[ Upstream commit 7c94dcfa8f ]
UDMA_CHAN_RT_*BCNT_REG stores the real-time channel bytecount statistics.
These registers are 32-bit hardware counters and the driver uses these
counters to monitor the operational progress status for a channel, when
transferring more than 4GB of data it was observed that these counters
overflow and completion calculation of a operation gets affected and the
transfer hangs indefinitely.
This commit adds changes to decrease the byte count for every complete
transaction so that these registers never overflow and the proper byte
count statistics is maintained for ongoing transaction by the RT counters.
Earlier uc->bcnt used to maintain a count of the completed bytes at driver
side, since the RT counters maintain the statistics of current transaction
now, the maintenance of uc->bcnt is not necessary.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20220802054835.19482-1-vaishnav.a@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c69400b09e ]
The xhci_plat_brcm xhci block can enter suspend with clock disabled to save
power and re-enable them on resume. Make use of the XHCI_SUSPEND_RESUME_CLKS
quirk to do so.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Link: https://lore.kernel.org/r/1660170455-15781-3-git-send-email-justinpopo6@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8bd954c561 ]
Introduce XHCI_SUSPEND_RESUME_CLKS quirk as a means to suspend and resume
clocks if the hardware is capable of doing so. We assume that clocks will
be needed if the device may wake.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Link: https://lore.kernel.org/r/1660170455-15781-2-git-send-email-justinpopo6@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30eaf02149 ]
The function zynqmp_pll_round_rate is used to find a most appropriate
PLL frequency which the hardware can generate according to the desired
frequency. For example, if the desired frequency is 297MHz, considering
the limited range from PS_PLL_VCO_MIN (1.5GHz) to PS_PLL_VCO_MAX (3.0GHz)
of PLL, zynqmp_pll_round_rate should return 1.872GHz (297MHz * 5).
There are two problems with the current code of zynqmp_pll_round_rate:
1) When the rate is below PS_PLL_VCO_MIN, it can't find a correct rate
when the parameter "rate" is an integer multiple of *prate, in other words,
if "f" is zero, zynqmp_pll_round_rate won't return a valid frequency which
is from PS_PLL_VCO_MIN to PS_PLL_VCO_MAX. For example, *prate is 33MHz
and the rate is 660MHz, zynqmp_pll_round_rate will not boost up rate and
just return 660MHz, and this will cause clk_calc_new_rates failure since
zynqmp_pll_round_rate returns an invalid rate out of its boundaries.
2) Even if the rate is higher than PS_PLL_VCO_MIN, there is still a risk
that zynqmp_pll_round_rate returns an invalid rate because the function
DIV_ROUND_CLOSEST makes some loss in the fractional part. If the parent
clock *prate is 33333333Hz and we want to set the PLL rate to 1.5GHz,
this function will return 1499999985Hz by using the formula below:
value = *prate * DIV_ROUND_CLOSEST(rate, *prate)).
This value is also invalid since it's slightly smaller than PS_PLL_VCO_MIN.
because DIV_ROUND_CLOSEST makes some loss in the fractional part.
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20220826142030.213805-1-quanyang.wang@windriver.com
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c65c3f3a2c ]
video_unregister_device will release device internally. There is no need to
call video_device_release after video_unregister_device.
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b064d9144 ]
When the driver calls cx88_risc_buffer() to prepare the buffer, the
function call may fail, resulting in a empty buffer and null-ptr-deref
later in buffer_queue().
The following log can reveal it:
[ 41.822762] general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN PTI
[ 41.824488] KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
[ 41.828027] RIP: 0010:buffer_queue+0xc2/0x500
[ 41.836311] Call Trace:
[ 41.836945] __enqueue_in_driver+0x141/0x360
[ 41.837262] vb2_start_streaming+0x62/0x4a0
[ 41.838216] vb2_core_streamon+0x1da/0x2c0
[ 41.838516] __vb2_init_fileio+0x981/0xbc0
[ 41.839141] __vb2_perform_fileio+0xbf9/0x1120
[ 41.840072] vb2_fop_read+0x20e/0x400
[ 41.840346] v4l2_read+0x215/0x290
[ 41.840603] vfs_read+0x162/0x4c0
Fix this by checking the return value of cx88_risc_buffer()
[hverkuil: fix coding style issues]
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbecac2663 ]
btrfs currently prints information about space cache or free space tree
being in use on every remount, regardless whether such remount actually
enabled or disabled one of these features.
This is actually unnecessary since providing remount options changing the
state of these features will explicitly print the appropriate notice.
Let's instead print such unconditional information just on an initial mount
to avoid filling the kernel log when, for example, laptop-mode-tools
remount the fs on some events.
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9eab5f0bb ]
[BUG]
The following script shows that, although scrub can detect super block
errors, it never tries to fix it:
mkfs.btrfs -f -d raid1 -m raid1 $dev1 $dev2
xfs_io -c "pwrite 67108864 4k" $dev2
mount $dev1 $mnt
btrfs scrub start -B $dev2
btrfs scrub start -Br $dev2
umount $mnt
The first scrub reports the super error correctly:
scrub done for f3289218-abd3-41ac-a630-202f766c0859
Scrub started: Tue Aug 2 14:44:11 2022
Status: finished
Duration: 0:00:00
Total to scrub: 1.26GiB
Rate: 0.00B/s
Error summary: super=1
Corrected: 0
Uncorrectable: 0
Unverified: 0
But the second read-only scrub still reports the same super error:
Scrub started: Tue Aug 2 14:44:11 2022
Status: finished
Duration: 0:00:00
Total to scrub: 1.26GiB
Rate: 0.00B/s
Error summary: super=1
Corrected: 0
Uncorrectable: 0
Unverified: 0
[CAUSE]
The comments already shows that super block can be easily fixed by
committing a transaction:
/*
* If we find an error in a super block, we just report it.
* They will get written with the next transaction commit
* anyway
*/
But the truth is, such assumption is not always true, and since scrub
should try to repair every error it found (except for read-only scrub),
we should really actively commit a transaction to fix this.
[FIX]
Just commit a transaction if we found any super block errors, after
everything else is done.
We cannot do this just after scrub_supers(), as
btrfs_commit_transaction() will try to pause and wait for the running
scrub, thus we can not call it with scrub_lock hold.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62cd9d4474 ]
There is an internal report on hitting the following ASSERT() in
recalculate_thresholds():
ASSERT(ctl->total_bitmaps <= max_bitmaps);
Above @max_bitmaps is calculated using the following variables:
- bytes_per_bg
8 * 4096 * 4096 (128M) for x86_64/x86.
- block_group->length
The length of the block group.
@max_bitmaps is the rounded up value of block_group->length / 128M.
Normally one free space cache should not have more bitmaps than above
value, but when it happens the ASSERT() can be triggered if
CONFIG_BTRFS_ASSERT is also enabled.
But the ASSERT() itself won't provide enough info to know which is going
wrong.
Is the bg too small thus it only allows one bitmap?
Or is there something else wrong?
So although I haven't found extra reports or crash dump to do further
investigation, add the extra info to make it more helpful to debug.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6effe295e1 ]
This allows the userspace to notice that there's not enough
current provided to charge the battery, and also fixes issues
with 0% SOC values being considered invalid.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c152c2f66 ]
When arm64 signal context data overflows the base struct sigcontext it gets
placed in an extra buffer pointed to by a record of type EXTRA_CONTEXT in
the base struct sigcontext which is required to be the last record in the
base struct sigframe. The current validation code attempts to check this
by using GET_RESV_NEXT_HEAD() to step forward from the current record to
the next but that is a macro which assumes it is being provided with a
struct _aarch64_ctx and uses the size there to skip forward to the next
record. Instead validate_extra_context() passes it a struct extra_context
which has a separate size field. This compiles but results in us trying
to validate a termination record in completely the wrong place, at best
failing validation and at worst just segfaulting. Fix this by passing
the struct _aarch64_ctx we meant to into the macro.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220829160703.874492-4-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 415432c008 ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7492a83ed9 ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60c9213a1d ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 088fe52374 ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@940000: '#address-cells' is a required property
sram@940000: '#size-cells' is a required property
sram@940000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5848b9563 ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b11d083c5d ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7c4ebe2f9 ]
Use the general touchscreen method to config the max pressure for
touch tsc2046(data sheet suggest 8 bit pressure), otherwise, for
ABS_PRESSURE, when config the same max and min value, weston will
meet the following issue,
[17:19:39.183] event1 - ADS7846 Touchscreen: is tagged by udev as: Touchscreen
[17:19:39.183] event1 - ADS7846 Touchscreen: kernel bug: device has min == max on ABS_PRESSURE
[17:19:39.183] event1 - ADS7846 Touchscreen: was rejected
[17:19:39.183] event1 - not using input device '/dev/input/event1'
This will then cause the APP weston-touch-calibrator can't list touch devices.
root@imx6ul7d:~# weston-touch-calibrator
could not load cursor 'dnd-move'
could not load cursor 'dnd-copy'
could not load cursor 'dnd-none'
No devices listed.
And accroding to binding Doc, "ti,x-max", "ti,y-max", "ti,pressure-max"
belong to the deprecated properties, so remove them. Also for "ti,x-min",
"ti,y-min", "ti,x-plate-ohms", the value set in dts equal to the default
value in driver, so are redundant, also remove here.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97d8d6f075 ]
[why]
Only a single VLINE interrupt is available so interface should not
expose the second one which is used by DMU firmware.
[how]
Remove references to periodic_interrupt1 and VLINE1 from DC interfaces.
Reviewed-by: Jaehyun Chung <jaehyun.chung@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b4d8db657 ]
The sequence for Source DP PHY CTS automation is [2][1]:
1- Emulate successful Link Training(LT)
2- Short HPD and change link rates and number of lanes by LT.
(This is same flow for Link Layer CTS)
3- Short HPD and change PHY test pattern and swing/pre-emphasis
levels (This step should not trigger LT)
The problem is with DP PHY compliance setup as follow:
[DPTX + on board LTTPR]------Main Link--->[Scope]
^ |
| |
| |
----------Aux Ch------>[Aux Emulator]
At step 3, before writing TRAINING_LANEx_SET/LINK_QUAL_PATTERN_SET
to declare the pattern/swing requested by scope, we write link
config in LINK_BW_SET/LANE_COUNT_SET on a port that has LTTPR.
As LTTPR snoops aux transaction, LINK_BW_SET/LANE_COUNT_SET writes
indicate a LT will start [Check DP 2.0 E11 -Sec 3.6.8.2 & 3.6.8.6.3],
and LTTPR will reset the link and stop sending DP signals to
DPTX/Scope causing the measurements to fail. Note that step 3 will
not trigger LT and DP link will never recovered by the
Aux Emulator/Scope.
The reset of link can be tested with a monitor connected to LTTPR
port simply by writing to LINK_BW_SET or LANE_COUNT_SET as follow
igt/tools/dpcd_reg write --offset=0x100 --value 0x14 --device=2
OR
printf '\x14' | sudo dd of=/dev/drm_dp_aux2 bs=1 count=1 conv=notrunc
seek=$((0x100))
This single aux write causes the screen to blank, sending short HPD to
DPTX, setting LINK_STATUS_UPDATE = 1 in DPCD 0x204, and triggering LT.
As stated in [1]:
"Before any TX electrical testing can be performed, the link between a
DPTX and DPRX (in this case, a piece of test equipment), including all
LTTPRs within the path, shall be trained as defined in this Standard."
In addition, changing Phy pattern/Swing/Pre-emphasis (Step 3) uses the
same link rate and lane count applied on step 2, so no need to redo LT.
The fix is to not rewrite link config in step 3, and just writes
TRAINING_LANEx_SET and LINK_QUAL_PATTERN_SET
[1]: DP 2.0 E11 - 3.6.11.1 LTTPR DPTX_PHY Electrical Compliance
[2]: Configuring UnigrafDPTC Controller - Automation Test Sequence
https://www.keysight.com/us/en/assets/9922-01244/help-files/
D9040DPPC-DisplayPort-Test-Software-Online-Help-latest.chm
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Or Cochvi <or.cochvi@intel.com>
Signed-off-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916054900.415804-1-khaled.almahallawy@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4de95950d9 ]
The Snapdragon 670 has the same quirk as Snapdragon 845 (needing to
restore the dll config). Add a compatible string check to detect the need
for this.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220923014322.33620-3-mailingradian@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bb71fce58 ]
This got lost somewhere along the way, This fixes
audio not working until set_property was called.
Signed-off-by: hongao <hongao@uniontech.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1c1fc8103 ]
In some Chrome platforms if OEM's use their own string as SYS_VENDOR than
"Google", it leads to firmware load failure from intel/sof/community path.
Hence, changing SYS_VENDOR to PRODUCT_FAMILY in which "Google" is used
as common prefix and is supported in all Chrome platforms.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Chao Song <chao.song@intel.com>
Reviewed-by: Curtis Malainey <curtis@malainey.com>
Signed-off-by: Jairaj Arava <jairaj.arava@intel.com>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220919114429.42700-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a2565272a ]
On a MSI S270 with Fedora 37 x86_64 / systemd-251.4 the module does not
properly autoload.
This is likely caused by issues with how systemd-udevd handles the single
quote char (') which is part of the sys_vendor / chassis_vendor strings
on this laptop. As a workaround remove the single quote char + everything
behind it from the sys_vendor + chassis_vendor matches. This fixes
the module not autoloading.
Link: https://github.com/systemd/systemd/issues/24715
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220917210407.647432-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8edd2752b0 ]
cros_ec_handle_event in the cros_ec driver can notify the PM of wake
events. When a device is suspended, cros_ec_handle_event will not check
MKBP events. Instead, received MKBP events are checked during resume by
cros_ec_report_events_during_suspend. But
cros_ec_report_events_during_suspend cannot notify the PM if received
events are wake events, causing wake events to not be reported if
received while the device is suspended.
Update cros_ec_report_events_during_suspend to notify the PM of wake
events during resume by calling pm_wakeup_event.
Signed-off-by: Jameson Thies <jthies@google.com>
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220913204954.2931042-1-jthies@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 770e190760 ]
This device is another x86 gaming handheld, and as (hopefully) there is
only one set of DMI IDs it's using DMI_EXACT_MATCH
Signed-off-by: Maya Matuszczyk <maccraft123mc@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220803182402.1217293-1-maccraft123mc@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30d7565be9 ]
This commit fixes vertical timings of the VEC (composite output) modes
to accurately represent the 525-line ("NTSC") and 625-line ("PAL") ITU-R
standards.
Previous timings were actually defined as 502 and 601 lines, resulting
in non-standard 62.69 Hz and 52 Hz signals being generated,
respectively.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220728-rpi-analog-tv-properties-v2-28-459522d653a7@cerno.tech
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6392dcd1d0 ]
The USB-audio driver matches per interface, and as default, it
registers the card instance at the very first instance. This can be a
problem for the devices that have multiple interfaces to be probed, as
the udev rule isn't applied properly for the later appearing
interfaces. Although we introduced the delayed_register option and
the quirks for covering those shortcomings, it's nothing but a
workaround for specific devices.
This patch is an another attempt to fix the problem in a more generic
way. Now the driver checks the whole USB device descriptor at the
very first time when an interface is attached to a sound card. It
looks at each matching interface in the descriptor and remembers the
last matching one. The snd_card_register() is invoked only when this
last interface is probed.
After this change, the quirks for the delayed registration become
superfluous, hence they are removed along with the patch. OTOH, the
delayed_register option is still kept, as it might be useful for some
corner cases (e.g. a special driver overtakes the interface probe from
the standard driver, and the last interface probe may miss).
Link: https://lore.kernel.org/r/20220904161247.16461-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da09daf881 ]
There are two events that signal a real change of the link state: HPD going
high means the sink is newly connected or wants the source to re-read the
EDID, RX sense going low is a indication that the link has been disconnected.
Ignore the other two events that also trigger interrupts, but don't need
immediate attention: HPD going low does not necessarily mean the link has
been lost and should not trigger a immediate read of the status. RX sense
going high also does not require a detect cycle, as HPD going high is the
right point in time to read the EDID.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> (v1)
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220826185733.3213248-1-l.stach@pengutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ae0632d17 ]
The definition of MIN_I64 in bw_fixed.c can cause gcc to whinge about
integer overflow, because it is treated as a positive value, which is
then negated. The temporary positive value is not necessarily
representable.
This causes the following warning:
../drivers/gpu/drm/amd/amdgpu/../display/dc/dml/calcs/bw_fixed.c:30:19:
warning: integer overflow in expression ‘-9223372036854775808’ of type
‘long long int’ results in ‘-9223372036854775808’ [-Woverflow]
30 | (int64_t)(-(1LL << 63))
| ^
Writing out (-MAX_I64 - 1) works instead.
Signed-off-by: David Gow <davidgow@google.com>
Signed-off-by: Tales Aparecida <tales.aparecida@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef8886f321 ]
A NULL check for bridge->encoder shows that it may be NULL, but it
already been dereferenced on all paths leading to the check.
812 if (!bridge->encoder) {
Dereference the pointer bridge->encoder.
810 drm_connector_attach_encoder(<9611->connector, bridge->encoder);
Signed-off-by: Zeng Jingxiang <linuszeng@tencent.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220727073119.1578972-1-zengjx95@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eaa225b6b5 ]
Komeda driver relies on the generic DRM atomic helper functions to handle
commits. It only implements an atomic_commit_tail hook for the
mode_config_helper_funcs and even that one is pretty close to the generic
implementation with the exception of additional dma_fence signalling.
What the generic helper framework doesn't do is waiting for the actual
hardware to signal that the commit parameters have been written into the
appropriate registers. As we signal CRTC events only on the irq handlers,
we need to flush the configuration and wait for the hardware to respond.
Add the Komeda specific implementation for atomic_commit_hw_done() that
flushes and waits for flip done before calling drm_atomic_helper_commit_hw_done().
The fix was prompted by a patch from Carsten Haitzler where he was trying to
solve the same issue but in a different way that I think can lead to wrong
event signaling to userspace.
Reported-by: Carsten Haitzler <carsten.haitzler@arm.com>
Tested-by: Carsten Haitzler <carsten.haitzler@arm.com>
Reviewed-by: Carsten Haitzler <carsten.haitzler@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220722122139.288486-1-liviu.dudau@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94dc3471d1 ]
The strlen() function returns a size_t which is an unsigned int on 32-bit
arches and an unsigned long on 64-bit arches. But in the drm_copy_field()
function, the strlen() return value is assigned to an 'int len' variable.
Later, the len variable is passed as copy_from_user() third argument that
is an unsigned long parameter as well.
In theory, this can lead to an integer overflow via type conversion. Since
the assignment happens to a signed int lvalue instead of a size_t lvalue.
In practice though, that's unlikely since the values copied are set by DRM
drivers and not controlled by userspace. But using a size_t for len is the
correct thing to do anyways.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220705100215.572498-2-javierm@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6dc548745d ]
nouveau_bo_alloc() allocates a memory chunk for "nvbo" with kzalloc().
When some error occurs, "nvbo" should be released. But when
WARN_ON(pi < 0)) equals true, the function return ERR_PTR without
releasing the "nvbo", which will lead to a memory leak.
We should release the "nvbo" with kfree() if WARN_ON(pi < 0)) equals true.
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220705094306.2244103-1-niejianglei2021@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93e2be344a ]
My system shows almost 10 million of these messages over a 24-hour
period which pollutes my logs.
Signed-off-by: Andrew Gaul <gaul@google.com>
Link: https://lore.kernel.org/r/20221002034128.2026653-1-gaul@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9c0cf8f26 ]
On 32-bit platforms, long is 32 bits, so (long)UINT_MAX is less than
(long)SHT4X_MIN_POLL_INTERVAL, which means the clamping operation is
bogus. Fix this by clamping at INT_MAX, so that the upperbound is the
same on all platforms.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Link: https://lore.kernel.org/r/20220924101151.4168414-1-Jason@zx2c4.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbde6ed406 ]
Instead of using the default value 33 (pci), set US_CYC_CNT init based
on Programming guide:
If available, set chipset bus clock with fallback to cpu clock/3.
Reported-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/3e275d259f476f597dab91a9c395015ef3fe3284.1663445157.git.daniel@makrotopia.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3aad83d05 ]
The function rt2800_iq_calibrate is intended for Rt5592 only.
Don't call it for MT7620 which has it's own calibration functions.
Reported-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/31a1c34ddbd296b82f38c18c9ae7339059215fdc.1663445157.git.daniel@makrotopia.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3fd7bfd28c ]
If can_send() fail, it should not update frames_abs counter
in bcm_can_tx(). Add the result check for can_send() in bcm_can_tx().
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Suggested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Link: https://lore.kernel.org/all/9851878e74d6d37aee2f1ee76d68361a46f89458.1663206163.git.william.xuanziyang@huawei.com
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vaishnav Achath
Justin Chen
Quanyang Wang
Hangyu Hua
Zheyu Ma
Ian Nam
Alex Sverdlin
Maciej S. Szmigiero
Qu Wenruo
Sebastian Krzyszkowiak
Mark Brown
Alexander Stein
Haibo Chen
Aric Cyr
Khaled Almahallawy
Richard Acayan
Adrián Larumbe
hongao
Jairaj Arava
Hans de Goede
Jameson Thies
Maya Matuszczyk
Mateusz Kwiatkowski
Takashi Iwai
Lucas Stach
Vivek Kasireddy
David Gow
Zeng Jingxiang
Liviu Dudau
Javier Martinez Canillas
Jianglei Nie
Andrew Gaul
Luiz Augusto von Dentz
Liu Jian
Jason A. Donenfeld
Daniel Golle
Ziyang Xuan