Daniel Vetter wrote
First pull request for 3.5-next, slightly large than usual because new
things kept coming in since the last pull for 3.4.
Highlights:
- first batch of hw enablement for vlv (Jesse et al) and hsw (Eugeni). pci
ids are not yet added, and there's still quite a few patches to merge
(mostly modesetting). To make QA easier I've decided to merge this stuff
in pieces.
- loads of cleanups and prep patches spurred by the above. Especially vlv
is a real frankenstein chip, but also hsw is stretching our driver's
code design. Expect more to come in this area for 3.5.
- more gmbus fixes, cleanups and improvements by Daniel Kurtz. Again,
there are more patches needed (and some already queued up), but I wanted
to split this a bit for better testing.
- pwrite/pread rework and retuning. This series has been in the works for
a few months already and a lot of i-g-t tests have been created for it.
Now it's finally ready to be merged. Note that one patch in this series
touches include/pagemap.h, that patch is acked-by akpm.
- reduce mappable pressure and relocation throughput improvements from
Chris.
- mmap offset exhaustion mitigation by Chris Wilson.
- a start at figuring out which codepaths in our messy dri1/ums+gem/kms
driver we actually need to support by bailing out of unsupported case.
The driver now refuses to load without kms on gen6+ and disallows a few
ioctls that userspace never used in certain cases. More of this will
definitely come.
- More decoupling of global gtt and ppgtt.
- Improved dual-link lvds detection by Takashi Iwai.
- Shut up the compiler + plus fix the fallout (Ben)
- Inverted panel brightness handling (mostly Acer manages to break things
in this way).
- Small fixlets and adjustements and some minor things to help debugging.
Regression-wise QA reported quite a few issues on ivb, but all of them
turned out to be hw stability issues which are already fixed in
drm-intel-fixes (QA runs the nightly regression tests on -next alone,
without -fixes automatically merged in). There's still one issue open on
snb, it looks like occlusion query writes are not quite as cache coherent
as we've expected. With some of the pwrite adjustements we can now
reliably hit this. Kernel workaround for it is in the works."
* 'drm-intel-next' of git://people.freedesktop.org/~danvet/drm-intel: (101 commits)
drm/i915: VCS is not the last ring
drm/i915: Add a dual link lvds quirk for MacBook Pro 8,2
drm/i915: make quirks more verbose
drm/i915: dump the DMA fetch addr register on pre-gen6
drm/i915/sdvo: Include YRPB as an additional TV output type
drm/i915: disallow gem init ioctl on ilk
drm/i915: refuse to load on gen6+ without kms
drm/i915: extract gt interrupt handler
drm/i915: use render gen to switch ring irq functions
drm/i915: rip out old HWSTAM missed irq WA for vlv
drm/i915: open code gen6+ ring irqs
drm/i915: ring irq cleanups
drm/i915: add SFUSE_STRAP registers for digital port detection
drm/i915: add WM_LINETIME registers
drm/i915: add WRPLL clocks
drm/i915: add LCPLL control registers
drm/i915: add SSC offsets for SBI access
drm/i915: add port clock selection support for HSW
drm/i915: add S PLL control
drm/i915: add PIXCLK_GATE register
...
Conflicts:
drivers/char/agp/intel-agp.h
drivers/char/agp/intel-gtt.c
drivers/gpu/drm/i915/i915_debugfs.c
It exists way back to gen2, bug got moved around on gen4 a bit.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- gen6 put/get only need one argument
rflags and gflags are always the same (see above explanation)
- remove a couple redundantly defined IRQs
- reordered some lines to make things go in descending order
Every ring has its own interrupts, enables, masks, and status bits that
are fed into the main interrupt enable/mask/status registers. At one
point in time it seemed like a good idea to make our functions support
the notion that each interrupt may have a different bit position in the
corresponding register (blitter parser error may be bit n in IMR, but
bit m in blitter IMR). It turned out though that the HW designers did us
a solid on Gen6+ and this unfortunate situation has been avoided. This
allows our interrupt code to be cleaned up a bit.
I jammed this into one commit because there should be no functional
change with this commit, and staging it into multiple commits was
unnecessarily artificial IMO.
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet:
- fixed up merged conflict with vlv changes.
- added GEN6 to GT blitter bit, we only use it on gen6+.
- added a comment to both ring irq bits and GT irq bits that on gen6+
these alias.
- added comment that GT_BSD_USER_INTERRUPT is ilk-only.
- I've got confused a bit that we still use GT_USER_INTERRUPT on ivb
for the render ring - but this goes back to ilk where we have only
gt interrupt bits and so we be equally confusing if changed.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DDIA is detected via the DDI_BUF_CTL registers bit 0, but for DDIB, DDIC
and DDID we need to consult SFUSE_STRAP values.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Watermark line time registers for display low power watermark.
v2: improve bit names as suggested by Chris Wilson
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The WR PLL can drive the DDI ports at fixed frequencies for HDMI, DVI, DP
and FDI.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Those are used to control the display core clock.
v2: change the enable bit setting, spotted by Rodrigo Vivi.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Different registers are identified by their target id and offset. To
simplify their programming, they are called as <RegisterName><TargetId>.
For example, SSCCTL register accessed through SBI at target id 6 and
offset 0c is called SBI_SSCCTL6.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Multiple clocks can drive different outputs.
v2: use the port enums to access individual ports
v1 Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This PLL control can drive DDI ports at desired frequencies for
DisplayPort and FDI connections.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Those are responsible for the Sideband Interface programming.
v2: rename SBI bits to better reflect their meaning
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Those registers are used to train DDI buffer translations for each link
type.
v2: access each port registers through the DDI_BUF_TRANS macro
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is one instance of those registers for each DDI port.
v2: access registers via the DDI_BUF_CTL() macro
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is one set of those registers for each port.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is one set of those registers for each pipe.
v2: use port enum to access individual registers
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is one set of such registers for each pipe (A/B/C/EDP).
v2: update to use DDI PORTS enum
v1 Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are 5 DDI ports on Haswell. Port A is always enabled, and is the one
connected to eDP, and Port E is the one that can be connected to the PCH
using FDI protocol. Ports B, C, D and E can be used for digital outputs.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This defines the registers used by different power wells.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Quoting the BSpec from time immemorial:
PIPEACONF, bits 28:27: Frame Start Delay (Debug)
Used to delay the frame start signal that is sent to the display planes.
Care must be taken to insure that there are enough lines during VBLANK
to support this setting.
An instance of the BIOS leaving these bits set was found in the wild,
where it caused our modesetting to go all squiffy and skewiff.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=47271
Reported-and-tested-by: Eva Wang <evawang@linpus.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43012
Reported-and-tested-by: Carl Richell <carl@system76.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ValleyView has a new interrupt architecture; best to put it in a new set
of functions. Also make sure the ring mask functions handle ValleyView.
FIXME: fix flipping; need to enable interrupts and call prepare/finish
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ValleyView handles force wake differently than previous chipsets, so add
a couple of new functions for it. But leave it disabled by default
until we test it (need a chip with the Punit enabled first).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HDMI register offsets are different in Valleyview. Add support for the
same.
v2: drop superfluous comments in HDMI init (Daniel)
Signed-off-by: Beeresh G <beeresh.g@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Reviewed-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Set required clock gating and chicken bits on VLV.
v2: set PIXEL_SUBSPAN_COLLECT_OPT_DISABLE too (Ben)
move function below ivb version to pretend to be consistent (Ben)
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ValleyView puts some display related registers like the PLL controls and
dividers behind the DPIO bus. Add simple indirect register access
routines to get to those registers.
v2: move new wait_for macro to intel_drv.h (Ben)
fix DPIO_PKT double write (Ben)
add debugfs file
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add support for ValleyView watermark handling.
v2: remove unused reg & bit definitions (Ben)
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no GMBUS "disabled" port 0, nor "reserved" port 7.
For the other 6 ports there is a fixed 1:1 mapping between pin pairs and
gmbus ports, which means every real gmbus port has a gpio pin.
Given these realizations, clean up gmbus initialization.
Tested on Sandybridge (gen 6, PCH == CougarPoint) hardware.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to i915 documentation [1], "Port D" (DP/HDMI Port D) is
actually gmbus pin pair 6 (gmbus0.2:0 == 110b GPIOF), not 7 (111b).
Pin pair 7 is a reserved pair.
[1] Documentation for [DevSNB+] and [DevIBX], as found on
http://intellinuxgraphics.org:
[DevSNB+]:
http://intellinuxgraphics.org/documentation/SNB/IHD_OS_Vol3_Part3.pdf
Section 2.2.2 lists the 6 gmbus ports (gpio pin pairs):
[ 5: HDMI/DPD, 4: HDMIB, 3: HDMI/DPC, 2: LVDS, 1: SSC, 0: VGA ]
2.2.2.1 lists the GPIO registers to control these 6 ports.
2.2.3.1 lists the mapping between 5 of these gmbus ports and the 3
Pin_Pair_Select bits (of the GMBUS0 register). This table is missing
HDMIB (port 101).
[DevIBX]: http://intellinuxgraphics.org/IHD_OS_Vol3_Part3r2.pdf
Section 2.2.2 lists the same 6 gmbus ports plus two 'reserved' gpio
ports.
2.2.2.1 lists 8 GPIO registers... however, it says the size of the
block is 6x32, which implies that those 2 reserved GPIO registers
(GPIO_6 & GPIO_7) don't actually exist (or are irrelevant).
2.2.3.1 lists the mapping between the 6 named gmbus ports and the 3
Pin_Pair_Select bits (of the GMBUS0 register). This table has HDMIB.
Note: the "reserved" and "disabled" pairs do not actually map to a
physical pair of pins, nor GPIO regs and shouldn't be initialized or used.
Fixing this is left for a later patch.
This bug had not been noticed earlier for two reasons:
1) Until recently, "gmbus" mode was disabled - all transfers actually
used "bit-bang" mode on GPIO port 5 (the "HDMI/DPD CTLDATA/CLK"
pair), at register 0x5024 (defined as GPIOF i915_reg.h).
Since this is the correct pair of pins for HDMI1, transfers succeed.
2) Even if gmbus mode is re-enabled, the first attempted transaction
will fail because it tries to use the wrong ("Reserved") pin pair.
However, the driver immediately falls back again to the bit-bang
method, which correctly uses GPIOF, so again, transfers succeed.
However, if gmbus mode is re-enabled and the GPIO fall-back mode is
disabled, then reading an attached monitor's EDID fail.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They were all over the place, order them by position and add a few.
v2: add gen indications to the new bits (Ben)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm main changes from Dave Airlie:
"This is the main drm pull request, I'm probably going to send two more
smaller ones, will explain below.
This contains a patch that is also in the fbdev tree, but it should be
the same patch, it added an API for hot unplugging framebuffer
devices, and I need that API for a new driver.
It also contains some changes to the i2c tree which Jean has acked,
and one change to moorestown platform stuff in x86.
Highlights:
- new drivers: UDL driver for USB displaylink devices, kms only,
should support correct hotplug operations.
- core: i2c speedups + better hotplug support, EDID overriding via
firmware interface - allows user to load a firmware for a broken
monitor/kvm from userspace, it even has documentation for it.
- exynos: new HDMI audio + hdmi 1.4 + virtual output driver
- gma500: code cleanup
- radeon: cleanups, CS optimisations, streamout support and pageflip
fix
- nouveau: NVD9 displayport support + more reclocking work
- i915: re-enabling GMBUS, finish gpu patch (might help hibernation
who knows), missed irq fixes, stencil tiling fixes, interlaced
support, aliasesd PPGTT support for SNB/IVB, swizzling for SNB/IVB,
semaphore fixes
As well as the usual bunch of cleanups and fixes all over the place.
I've got two things I'd like to merge a bit later:
a) AMD support for all their new radeonhd 7000 series GPU and APUs.
AMD dropped this a bit late due to insane internal review
processes, (please AMD just follow Intel and let open source guys
ship stuff early) however I don't want to penalise people who own
this hardware (since its been on sale for 3-4 months and GPU hw
doesn't exactly have a lifetime in years) and consign them to
using closed drivers for longer than necessary. The changes are
well contained and just plug into the driver new gpu functionality
so they should be fairly regression proof. I just want to give
them a bit of a run on the hw AMD kindly sent me.
b) drm prime/dma-buf interface code. This is just infrastructure
code to expose the dma-buf stuff to drm drivers and to userspace.
I'm not planning on pushing any driver support in this cycle
(except maybe exynos), but I'd like to get the infrastructure code
in so for the next cycle I can start getting the driver support
into the individual drivers. We have started driver support for
i915, nouveau and udl along with I think exynos and omap in
staging. However this code relies on the dma-buf tree being
pulled into your tree first since it needs the latest interfaces
from that tree. I'll push to get that tree sent asap.
(oh and any warnings you see in i915 are gcc's fault from what anyone
can see)."
Fix up trivial conflicts in arch/x86/platform/mrst/mrst.c due to the new
msic_thermal_platform_data() thermal function being added next to the
tc35876x_platform_data() i2c device function..
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (326 commits)
drm/i915: use DDC_ADDR instead of hard-coding it
drm/radeon: use DDC_ADDR instead of hard-coding it
drm: remove unneeded redefinition of DDC_ADDR
drm/exynos: added virtual display driver.
drm: allow loading an EDID as firmware to override broken monitor
drm/exynos: enable hdmi audio feature
drm/exynos: add default pixel format for plane
drm/exynos: cleanup exynos_hdmi.h
drm/exynos: add is_local member in exynos_drm_subdrv struct
drm/exynos: add subdrv open/close functions
drm/exynos: remove module of exynos drm subdrv
drm/exynos: release pending pageflip events when closed
drm/exynos: added new funtion to get/put dma address.
drm/exynos: update gem and buffer framework.
drm/exynos: added mode_fixup feature and code clean.
drm/exynos: add HDMI version 1.4 support
drm/exynos: remove exynos_mixer.h
gma500: Fix mmap frambuffer
drm/radeon: Drop radeon_gem_object_(un)pin.
drm/radeon: Restrict offset for legacy display engine.
...
This was pointed by Jesse Barnes. The code now seems to follow the
specification but I don't have an SDVO device to really test this.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add register definitions for GTFIFODBG, and clear it during init time to
make sure state is correct.
This register tells us if either a read, or a write occurred while the
fifo was full. It seems like bit 2 is an OR of bit 0 and bit 1, so we
check that as well, but the documents are not quite clear.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by (v1): Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This adds the workaround for WaCatErrorRejectionIssue which could result
in a system hang.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41353
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44610
Tested-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This adds two cache-related workarounds for Ivy Bridge which can lead to
3D ring hangs and corruptions.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41353
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44610
Tested-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This is yet another workaround related to clock gating which we need on
Ivy Bridge.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41353
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44610
Tested-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
I'm not sure why they are needed (I didn't notice any difference in my
tests), but these bits are in our documentation and they are also set by
the Windows driver.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The hw seems to use this to correctly insert the required delay
before/after an even/odd interlaced field. This might also explain
why we need to substract 1 half-line from vtotal - if the hw just
adds the delay programmend in VSYNCSHIFT the total frame time would be
about that too long.
These registers seems to only exist on gen4 and later. For paranoia
also program it to 0 for progressive modes, but according to
documentation the hw should just ignore it in this case.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Alfonso Fiore <alfonso.fiore@gmail.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Clarify which bits are for which chips.
- Note that gen2 can't do interlaced directly (only via dvo tv chips).
- Move the mask to the top to make it clearer how wide this field is.
- Add defintions for all possible values.
This patch doesn't change any code.
v2: Paulo Zanoni pointed out that the pixel doubling modes do no
longer exist on ivb.
Cc: Peter Ross <pross@xvid.org>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Christopher Egert <cme3000@gmail.com>
Tested-by: Alfonso Fiore <alfonso.fiore@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Split out for easier cross-checking of the boring pieces with bspec.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This just adds the setup and teardown code for the ppgtt PDE and the
last-level pagetables, which are fixed for the entire lifetime, at
least for the moment.
v2: Kill the stray debug printk noted by and improve the pte
definitions as suggested by Chris Wilson.
v3: Clean up the aperture stealing code as noted by Ben Widawsky.
v4: Paint the init code in a more pleasing colour as suggest by Chris
Wilson.
v5: Explain the magic numbers noticed by Ben Widawsky.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have to do this manually. Somebody had a Great Idea.
I've measured speed-ups just a few percent above the noise level
(below 5% for the best case), but no slowdows. Chris Wilson measured
quite a bit more (10-20% above the usual snb variance) on a more
recent and better tuned version of sna, but also recorded a few
slow-downs on benchmarks know for uglier amounts of snb-induced
variance.
v2: Incorporate Ben Widawsky's preliminary review comments and
elaborate a bit about the performance impact in the changelog.
v3: Add a comment as to why we don't need to check the 3rd memory
channel.
v4: Fixup whitespace.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was pretty handy when figuring out what exactly went wrong with
ppgtt and it might also be useful when we stop filling the entire gart
with scratch page entries.
Also add the gen6+ DONE reg while at it.
v2: Chris Wilson suggested to allocate the error_state with kzalloc
for better paranoia. Also kill existing spurious clears of the
error_state while at it.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on a patch by Ben Widawsky, but with different colors
for the bikeshed.
In contrast to Ben's patch this one doesn't add the fault regs.
Afaics they're for the optional page fault support which
- we're not enabling
- and which seems to be unsupported by the hw team. Recent bspec
lacks tons of information about this that the public docs released
half a year back still contain.
Also dump ring HEAD/TAIL registers - I've recently seen a few
error_state where just guessing these is not good enough.
v2: Also dump INSTPM for every ring.
v3: Fix a few really silly goof-ups spotted by Chris Wilson.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The code already got unwieldy and we want to dump more per-ring
registers.
Only functional change is that we now also capture the video
ring registers on ilk.
v2: fixup a refactor fumble spotted by Chris Wilson.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dave Airlie
Daniel Vetter
Ben Widawsky
Eugeni Dodonov
Chris Wilson
Jesse Barnes
Shobhit Kumar
Gajanan Bhat
Daniel Kurtz
Linus Torvalds
Paulo Zanoni
Kenneth Graunke