The RPC and RPCD2 core clocks were added to the sections for internal
core clocks, while they are core clock outputs, visible from DT.
Move them to the correct sections.
Rename the ".rpc" clock on R-Car S4 to "rpc".
Fixup nearby whitespace to increase uniformity.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/a938b938f00939b9206d7fbaba78e2ef09915f5f.1649681891.git.geert+renesas@glider.be
Describe the various clocks used by the SPI Multi I/O Bus Controller
(RPC-IF) on the R-Car D3 SoC: RPCSRC internal clock, RPC{,D2} clocks
derived from it, and RPC-IF module clock.
The RPCSRC clock divider on R-Car D3 is very similar to the one on R-Car
E3, but uses a different pre-divider for the PLL0 parent. Add a new
macro to describe it, reusing the existing clock type for R-Car E3.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/3fd1e886b7737cd0e199603bae81d01be9dcf3aa.1648546700.git.geert+renesas@glider.be
Add clocks for MLP modules on Renesas R-Car E3 and D3 SoCs.
Similar to other R-Car Gen3 SoC, exact information on the parents of MLP
clocks on E3 and D3 is not available. However, since the parents of
these clocks are not anyhow software-controllable, the only harm from
this is inexact information exported via debugfs. So just keep the
parent set in the same way as with other Gen3 SoCs.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Link: https://lore.kernel.org/r/20211225193957.2195012-1-nikita.yoush@cogentembedded.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
R-Car D3 ZA2 clock is from PLL0D3 or S0,
and it can be controlled by ZA2CKCR.
It is needed for R-Car Sound, but is not used so far.
Using default settings is very enough at this point.
This patch adds it by DEF_FIXED().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87pmxclrmy.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Ensures RWDT remains alert throughout the boot process if enabled.
This patch applies the change to the following SoCs: r8a77950, r8a77951,
r8a77960, r8a77961, r8a77965, r8a77970, r8a77980, r8a77990 and r8a77995.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20200616162626.27944-3-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the CryptoCell module clocks and their parents for the CryptoCell
instances in the various Renesas R-Car Gen3 SoCs that do not have
support for them yet in their clock drivers (M3-W/W+, M3-N, E3, D3).
The R-Car H3 clock driver already supports these clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200124133137.15921-1-geert+renesas@glider.be
The clock sources of the AXI-bus clock (266.66 MHz) used for Audio-DMAC
DMA transfers are:
Channel R-Car H3 R-Car M3-W R-Car M3-N R-Car E3
---------------------------------------------------------------
Audio-DMAC0 S1D2 S1D2 S1D2 S1D2
Audio-DMAC1 S1D2 S1D2 S1D2 -
As a result, change the parent clocks of the Audio-DMAC{0,1} module
clocks on R-Car H3, R-Car M3-W, and R-Car M3-N to S1D2, and change the
parent clock of the Audio-DMAC0 module on R-Car E3 to S1D2.
NOTE: This information will be reflected in a future revision of the
R-Car Gen3 Hardware Manual.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Update R-Car D3, RZ/G2M, and RZ/G2E]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The R-Car Gen3 HardWare Manual Errata for Rev. 0.80 (Feb 28, 2018) added
the CPEX clock on R-Car D3. This clock can be selected as a clock
source for CMT1 (Compare Match Timer Type 1).
Add the missing clock to the DT bindings header, and implement support
for it in the clock driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
The R-Car Gen3 HardWare Manual Errata for Rev. 0.80 (Dec 22, 2017, and
Feb 28, 2018) removed the SSPSRC, SSP1, and SSP2 clocks on R-Car D3, as
this SoC does not have a Stream and Security Processor.
As these definitions were never used, they can just be removed.
The freed slots in the DT bindings header must not be reused, though.
Fixes: 714c53aa2e ("clk: renesas: Add r8a77995 CPG Core Clock Definitions")
Fixes: d71e851d82 ("clk: renesas: cpg-mssr: Add R8A77995 support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
R-Car Gen3 Hardware Manual Errata for Rev 0.80 of February 28, 2018,
removed the module clocks for the Video Input Module (VIN) channels 5-7
on R-Car D3, as they do not exist on this SoC.
Fixes: d71e851d82 ("clk: renesas: cpg-mssr: Add R8A77995 support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
According to the R-Car Gen3 Hardware Manual Rev 1.00, the parent clock
of the DU module clocks on R-Car D3 is S1D1.
Fixes: d71e851d82 ("clk: renesas: cpg-mssr: Add R8A77995 support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
According to R-Car Gen3 Hardware Manual Rev.1.00, R-Car D3 has the
RCLK Frequency Control Register (RCKCR), which determines the OSC and
RINT predivider values, and selection of the RCLK clock source between
RINT and the On-Chip Oscillator.
Hence change the OSC and RINT clock definitions to use the RCKCR
divider, and add the missing On-Chip Oscillator and RCLK clock source
switching logic.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 0.55 of
September 8, 2017, the parent clock of the INTC-AP module clock on R-Car
D3 is S1D2.
This change has no functional impact.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add R-Car D3 (R8A77995) Clock Pulse Generator / Module Standby and
Software Reset support, using the CPG/MSSR driver core and the common
R-Car Gen3 CPG code.
Based on the R-Car Series, 3rd Generation Hardware User's Manual, Rev.
0.55, Jun. 30, 2017.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Geert Uytterhoeven
Nikita Yushchenko
Wolfram Sang
Kuninori Morimoto
Niklas Söderlund
Ulrich Hecht
Jacopo Mondi
Takeshi Kihara
Stephen Boyd