There are two flow control mechanisms in TIPC; one at link level that
handles network congestion, burst control, and retransmission, and one
at connection level which' only remaining task is to prevent overflow
in the receiving socket buffer. In TIPC, the latter task has to be
solved end-to-end because messages can not be thrown away once they
have been accepted and delivered upwards from the link layer, i.e, we
can never permit the receive buffer to overflow.
Currently, this algorithm is message based. A counter in the receiving
socket keeps track of number of consumed messages, and sends a dedicated
acknowledge message back to the sender for each 256 consumed message.
A counter at the sending end keeps track of the sent, not yet
acknowledged messages, and blocks the sender if this number ever reaches
512 unacknowledged messages. When the missing acknowledge arrives, the
socket is then woken up for renewed transmission. This works well for
keeping the message flow running, as it almost never happens that a
sender socket is blocked this way.
A problem with the current mechanism is that it potentially is very
memory consuming. Since we don't distinguish between small and large
messages, we have to dimension the socket receive buffer according
to a worst-case of both. I.e., the window size must be chosen large
enough to sustain a reasonable throughput even for the smallest
messages, while we must still consider a scenario where all messages
are of maximum size. Hence, the current fix window size of 512 messages
and a maximum message size of 66k results in a receive buffer of 66 MB
when truesize(66k) = 131k is taken into account. It is possible to do
much better.
This commit introduces an algorithm where we instead use 1024-byte
blocks as base unit. This unit, always rounded upwards from the
actual message size, is used when we advertise windows as well as when
we count and acknowledge transmitted data. The advertised window is
based on the configured receive buffer size in such a way that even
the worst-case truesize/msgsize ratio always is covered. Since the
smallest possible message size (from a flow control viewpoint) now is
1024 bytes, we can safely assume this ratio to be less than four, which
is the value we are now using.
This way, we have been able to reduce the default receive buffer size
from 66 MB to 2 MB with maintained performance.
In order to keep this solution backwards compatible, we introduce a
new capability bit in the discovery protocol, and use this throughout
the message sending/reception path to always select the right unit.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nametable updates received from the network that cannot be applied
immediately are placed on a defer queue. This queue is global to the
TIPC module, which might cause problems when using TIPC in containers.
To prevent nametable updates from escaping into the wrong namespace,
we make the queue pernet instead.
Signed-off-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The broadcast transmission link is currently instantiated when the
network subsystem is started, i.e., on order from user space via netlink.
This forces the broadcast transmission code to do unnecessary tests for
the existence of the transmission link, as well in single mode node as
in network mode.
In this commit, we do instead create the link during initialization of
the name space, and remove it when it is stopped. The fact that the
transmission link now has a guaranteed longer life cycle than any of its
potential clients paves the way for further code simplifcations
and optimizations.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a topology server accepts a connection request from its client,
it allocates a connection instance and a tipc_subscriber structure
object. The former is used to communicate with client, and the latter
is often treated as a subscriber which manages all subscription events
requested from a same client. When a topology server receives a request
of subscribing name services from a client through the connection, it
creates a tipc_subscription structure instance which is seen as a
subscription recording what name services are subscribed. In order to
manage all subscriptions from a same client, topology server links
them into the subscrp_list of the subscriber. So subscriber and
subscription completely represents different meanings respectively,
but function names associated with them make us so confused that we
are unable to easily tell which function is against subscriber and
which is to subscription. So we want to eliminate the confusion by
renaming them.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When remove TIPC module, there is a warning to remind us that a slab
object is leaked like:
root@localhost:~# rmmod tipc
[ 19.056226] =============================================================================
[ 19.057549] BUG TIPC (Not tainted): Objects remaining in TIPC on kmem_cache_close()
[ 19.058736] -----------------------------------------------------------------------------
[ 19.058736]
[ 19.060287] INFO: Slab 0xffffea0000519a00 objects=23 used=1 fp=0xffff880014668b00 flags=0x100000000004080
[ 19.061915] INFO: Object 0xffff880014668000 @offset=0
[ 19.062717] kmem_cache_destroy TIPC: Slab cache still has objects
This is because the listening socket of TIPC topology server is not
closed before TIPC proto handler is unregistered with proto_unregister().
However, as the socket is closed in tipc_exit_net() which is called by
unregister_pernet_subsys() during unregistering TIPC namespace operation,
the warning can be eliminated if calling unregister_pernet_subsys() is
moved before calling proto_unregister().
Fixes: e05b31f4bf ("tipc: make tipc socket support net namespace")
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_CMD_NOOP to compat layer and remove the old framework.
All legacy nl commands are now converted to the compat layer in
netlink_compat.c.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new netlink API is no longer "v2" but rather the standard API and
the legacy API is now "nl compat". We split them into separate
start/stop and put them in different files in order to further
distinguish them.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After namespace is supported, each namespace should own its private
random value. So the global variable representing the random value
must be moved to tipc_net structure.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC establishes one subscriber server which allows users to subscribe
their interesting name service status. After tipc supports namespace,
one dedicated tipc stack instance is created for each namespace, and
each instance can be deemed as one independent TIPC node. As a result,
subscriber server must be built for each namespace.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If net namespace is supported in tipc, each namespace will be treated
as a separate tipc node. Therefore, every namespace must own its
private tipc node address. This means the "tipc_own_addr" global
variable of node address must be moved to tipc_net structure to
satisfy the requirement. It's turned out that users also can assign
node address for every namespace.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC name table is used to store the mapping relationship between
TIPC service name and socket port ID. When tipc supports namespace,
it allows users to publish service names only owned by a certain
namespace. Therefore, every namespace must have its private name
table to prevent service names published to one namespace from being
contaminated by other service names in another namespace. Therefore,
The name table global variable (ie, nametbl) and its lock must be
moved to tipc_net structure, and a parameter of namespace must be
added for necessary functions so that they can obtain name table
variable defined in tipc_net structure.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now tipc socket table is statically allocated as a global variable.
Through it, we can look up one socket instance with port ID, insert
a new socket instance to the table, and delete a socket from the
table. But when tipc supports net namespace, each namespace must own
its specific socket table. So the global variable of socket table
must be redefined in tipc_net structure. As a concequence, a new
socket table will be allocated when a new namespace is created, and
a socket table will be deallocated when namespace is destroyed.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Global variables associated with node table are below:
- node table list (node_htable)
- node hash table list (tipc_node_list)
- node table lock (node_list_lock)
- node number counter (tipc_num_nodes)
- node link number counter (tipc_num_links)
To make node table support namespace, above global variables must be
moved to tipc_net structure in order to keep secret for different
namespaces. As a consequence, these variables are allocated and
initialized when namespace is created, and deallocated when namespace
is destroyed. After the change, functions associated with these
variables have to utilize a namespace pointer to access them. So
adding namespace pointer as a parameter of these functions is the
major change made in the commit.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Involve namespace infrastructure, make the "tipc_net_id" global
variable aware of per namespace, and rename it to "net_id". In
order that the conversion can be successfully done, an instance
of networking namespace must be passed to relevant functions,
allowing them to access the "net_id" variable of per namespace.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the works of initializing and shutting down tipc module are done
in core.h and core.c files, so all stuffs which are not closely
associated with the two tasks should be moved to appropriate places.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove redundant wrapper functions like tipc_core_start() and
tipc_core_stop(), and directly move them to their callers, such
as tipc_init() and tipc_exit(), having us clearly know what are
really done in both initialization and deinitialzation functions.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As tipc reference table is statically allocated, its memory size
requested on stack initialization stage is quite big even if the
maximum port number is just restricted to 8191 currently, however,
the number already becomes insufficient in practice. But if the
maximum ports is allowed to its theory value - 2^32, its consumed
memory size will reach a ridiculously unacceptable value. Apart from
this, heavy tipc users spend a considerable amount of time in
tipc_sk_get() due to the read-lock on ref_table_lock.
If tipc reference table is converted with generic rhashtable, above
mentioned both disadvantages would be resolved respectively: making
use of the new resizable hash table can avoid locking on the lookup;
smaller memory size is required at initial stage, for example, 256
hash bucket slots are requested at the beginning phase instead of
allocating the entire 8191 slots in old mode. The hash table will
grow if entries exceeds 75% of table size up to a total table size
of 1M, and it will automatically shrink if usage falls below 30%,
but the minimum table size is allowed down to 256.
Also converts ref_table_lock to a separate mutex to protect hash table
mutations on write side. Lastly defers the release of the socket
reference using call_rcu() to allow using an RCU read-side protected
call to rhashtable_lookup().
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Erik Hugne <erik.hugne@ericsson.com>
Cc: Thomas Graf <tgraf@suug.ch>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reference table is now 'socket aware' instead of being generic,
and has in reality become a socket internal table. In order to be
able to minimize the API exposed by the socket layer towards the rest
of the stack, we now move the reference table definitions and functions
into the file socket.c, and rename the functions accordingly.
There are no functional changes in this commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We move the inline functions in the file port.h to socket.c, and modify
their names accordingly.
We move struct tipc_port and some macros to socket.h.
Finally, we remove the file port.h.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory overhead when allocating big buffers for data transfer may
be quite significant. E.g., truesize of a 64 KB buffer turns out
to be 132 KB, 2 x the requested size.
This invalidates the "worst case" calculation we have been
using to determine the default socket receive buffer limit,
which is based on the assumption that 1024x64KB = 67MB buffers
may be queued up on a socket.
Since TIPC connections cannot survive hitting the buffer limit,
we have to compensate for this overhead.
We do that in this commit by dividing the fix connection flow
control window from 1024 (2*512) messages to 512 (2*256). Since
older version nodes send out acks at 512 message intervals,
compatibility with such nodes is guaranteed, although performance
may be non-optimal in such cases.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the previous commits of this series, we removed all asynchronous
actions which were based on the tasklet handler - "tipc_k_signal()".
So the moment has now come when we can completely remove the tasklet
handler infrastructure. That is done with this commit.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the lacking of any credential, it's allowed to accept commands
requested from remote nodes to query the local node status, which is
prone to involve potential security risks. Instead, if we login to
a remote node with ssh command, this approach is not only more safe
than the remote management feature, but also it can give us more
permissions like changing the remote node configuration. So it's
reasonable for us to obsolete the remote management feature now.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Accidentally a side effect is involved by commit 6e967adf7(tipc:
relocate common functions from media to bearer). Now tipc stack
handler of receiving packets from netdevices as well as netdevice
notification handler are registered when bearer is enabled rather
than tipc module initialization stage, but the two handlers are
both unregistered in tipc module exit phase. If tipc module is
inserted and then immediately removed, the following warning
message will appear:
"dev_remove_pack: ffffffffa0380940 not found"
This is because in module insertion stage tipc stack packet handler
is not registered at all, but in module exit phase dev_remove_pack()
needs to remove it. Of course, dev_remove_pack() cannot find tipc
protocol handler from the kernel protocol handler list so that the
warning message is printed out.
But if registering the two handlers is adjusted from enabling bearer
phase into inserting module stage, the warning message will be
eliminated. Due to this change, tipc_core_start_net() and
tipc_core_stop_net() can be deleted as well.
Reported-by: Wang Weidong <wangweidong1@huawei.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tipc module is inserted, many tipc components are initialized
one by one. During the initialization period, if one of them is
failed, tipc_core_stop() will be called to stop all components
whatever corresponding components are created or not. To avoid to
release uncreated ones, relevant components have to add necessary
enabled flags indicating whether they are created or not.
But in the initialization stage, if one component is unsuccessfully
created, we will just destroy successfully created components before
the failed component instead of all components. All enabled flags
defined in components, in turn, become redundant. Additionally it's
also unnecessary to identify whether table.types is NULL in
tipc_nametbl_stop() because name stable has been definitely created
successfully when tipc_nametbl_stop() is called.
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In our ongoing effort to simplify the TIPC locking structure,
we see a need to remove the linked list for tipc_links
in the bearer. This can be explained as follows.
Currently, we have three different ways to access a link,
via three different lists/tables:
1: Via a node hash table:
Used by the time-critical outgoing/incoming data paths.
(e.g. link_send_sections_fast() and tipc_recv_msg() ):
grab net_lock(read)
find node from node hash table
grab node_lock
select link
grab bearer_lock
send_msg()
release bearer_lock
release node lock
release net_lock
2: Via a global linked list for nodes:
Used by configuration commands (link_cmd_set_value())
grab net_lock(read)
find node and link from global node list (using link name)
grab node_lock
update link
release node lock
release net_lock
(Same locking order as above. No problem.)
3: Via the bearer's linked link list:
Used by notifications from interface (e.g. tipc_disable_bearer() )
grab net_lock(write)
grab bearer_lock
get link ptr from bearer's link list
get node from link
grab node_lock
delete link
release node lock
release bearer_lock
release net_lock
(Different order from above, but works because we grab the
outer net_lock in write mode first, excluding all other access.)
The first major goal in our simplification effort is to get rid
of the "big" net_lock, replacing it with rcu-locks when accessing
the node list and node hash array. This will come in a later patch
series.
But to get there we first need to rewrite access methods ##2 and 3,
since removal of net_lock would introduce three major problems:
a) In access method #2, we access the link before taking the
protecting node_lock. This will not work once net_lock is gone,
so we will have to change the access order. We will deal with
this in a later commit in this series, "tipc: add node lock
protection to link found by link_find_link()".
b) When the outer protection from net_lock is gone, taking
bearer_lock and node_lock in opposite order of method 1) and 2)
will become an obvious deadlock hazard. This is fixed in the
commit ("tipc: remove bearer_lock from tipc_bearer struct")
later in this series.
c) Similar to what is described in problem a), access method #3
starts with using a link pointer that is unprotected by node_lock,
in order to via that pointer find the correct node struct and
lock it. Before we remove net_lock, this access order must be
altered. This is what we do with this commit.
We can avoid introducing problem problem c) by even here using the
global node list to find the node, before accessing its links. When
we loop though the node list we use the own bearer identity as search
criteria, thus easily finding the links that are associated to the
resetting/disabling bearer. It should be noted that although this
method is somewhat slower than the current list traversal, it is in
no way time critical. This is only about resetting or deleting links,
something that must be considered relatively infrequent events.
As a bonus, we can get rid of the mutual pointers between links and
bearers. After this commit, pointer dependency go in one direction
only: from the link to the bearer.
This commit pre-empts introduction of problem c) as described above.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
drivers/net/macvtap.c
Both minor merge hassles, simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, registering a TIPC stack handler in the network device layer
is done twice, once for Ethernet (eth_media) and Infiniband (ib_media)
repectively. But, as this registration is not media specific, we can
avoid some code duplication by moving the registering function to
the generic bearer layer, to the file bearer.c, and call it only once.
The same is true for the network device event notifier.
As a side effect, the two workqueues we are using for for setting up/
cleaning up media can now be eliminated. Furthermore, the array for
storing the specific media type structs, media_array[], can be entirely
deleted.
Note that the eth_started and ib_started flags were removed during the
code relocation. There is now only one call to bearer_setup and
bearer_cleanup, and these can logically not race against each other.
Despite its size, this cleanup work incurs no functional changes in TIPC.
In particular, it should be noted that the sequence ordering of received
packets is unaffected by this change, since packet reception never was
subject to any work queue handling in the first place.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'signal handler' service in TIPC is a mechanism that makes it
possible to postpone execution of functions, by launcing them into
a job queue for execution in a separate tasklet, independent of
the launching execution thread.
When we do rmmod on the tipc module, this service is stopped after
the network service. At the same time, the stopping of the network
service may itself launch jobs for execution, with the risk that these
functions may be scheduled for execution after the data structures
meant to be accessed by the job have already been deleted. We have
seen this happen, most often resulting in an oops.
This commit ensures that the signal handler is the very first to be
stopped when TIPC is shut down, so there are no surprises during
the cleanup of the other services.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the new socket-based TIPC server infrastructure has been
introduced, we can now convert the configuration server to use
it. Then we can take future steps to simplify the configuration
server locking policy.
Some minor reordering of initialization is done, due to the
dependency on having tipc_socket_init completed.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the new TIPC server infrastructure has been introduced, we can
now convert the TIPC topology server to it. We get two benefits
from doing this:
1) It simplifies the topology server locking policy. In the
original locking policy, we placed one spin lock pointer in the
tipc_subscriber structure to reuse the lock of the subscriber's
server port, controlling access to members of tipc_subscriber
instance. That is, we only used one lock to ensure both
tipc_port and tipc_subscriber members were safely accessed.
Now we introduce another spin lock for tipc_subscriber structure
only protecting themselves, to get a finer granularity locking
policy. Moreover, the change will allow us to make the topology
server code more readable and maintainable.
2) It fixes a bug where sent subscription events may be lost when
the topology port is congested. Using the new service, the
topology server now queues sent events into an outgoing buffer,
and then wakes up a sender process which has been blocked in
workqueue context. The process will keep picking events from the
buffer and send them to their respective subscribers, using the
kernel socket interface, until the buffer is empty. Even if the
socket is congested during transmission there is no risk that
events may be dropped, since the sender process may block when
needed.
Some minor reordering of initialization is done, since we now
have a scenario where the topology server must be started after
socket initialization has taken place, as the former depends
on the latter. And overall, we see a simplification of the
TIPC subscriber code in making this changeover.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per feedback from the netdev community, we change the buffer
overflow protection algorithm in receiving sockets so that it
always respects the nominal upper limit set in sk_rcvbuf.
Instead of scaling up from a small sk_rcvbuf value, which leads to
violation of the configured sk_rcvbuf limit, we now calculate the
weighted per-message limit by scaling down from a much bigger value,
still in the same field, according to the importance priority of the
received message.
To allow for administrative tunability of the socket receive buffer
size, we create a tipc_rmem sysctl variable to allow the user to
configure an even bigger value via sysctl command. It is a size of
three (min/default/max) to be consistent with things like tcp_rmem.
By default, the value initialized in tipc_rmem[1] is equal to the
receive socket size needed by a TIPC_CRITICAL_IMPORTANCE message.
This value is also set as the default value of sk_rcvbuf.
Originally-by: Jon Maloy <jon.maloy@ericsson.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
[Ying: added sysctl variation to Jon's original patch]
Signed-off-by: Ying Xue <ying.xue@windriver.com>
[PG: don't compile sysctl.c if not config'd; add Documentation]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add InfiniBand media type based on the ethernet media type.
The only real difference is that in case of InfiniBand, we need the entire
20 bytes of space reserved for media addresses, so the TIPC media type ID is
not explicitly stored in the packet payload.
Sample output of tipc-config:
# tipc-config -v -addr -netid -nt=all -p -m -b -n -ls
node address: <10.1.4>
current network id: 4711
Type Lower Upper Port Identity Publication Scope
0 167776257 167776257 <10.1.1:1855512577> 1855512578 cluster
167776260 167776260 <10.1.4:1216454657> 1216454658 zone
1 1 1 <10.1.4:1216479235> 1216479236 node
Ports:
1216479235: bound to {1,1}
1216454657: bound to {0,167776260}
Media:
eth
ib
Bearers:
ib:ib0
Nodes known:
<10.1.1>: up
Link <broadcast-link>
Window:20 packets
RX packets:0 fragments:0/0 bundles:0/0
TX packets:0 fragments:0/0 bundles:0/0
RX naks:0 defs:0 dups:0
TX naks:0 acks:0 dups:0
Congestion bearer:0 link:0 Send queue max:0 avg:0
Link <10.1.4:ib0-10.1.1:ib0>
ACTIVE MTU:2044 Priority:10 Tolerance:1500 ms Window:50 packets
RX packets:80 fragments:0/0 bundles:0/0
TX packets:40 fragments:0/0 bundles:0/0
TX profile sample:22 packets average:54 octets
0-64:100% -256:0% -1024:0% -4096:0% -16384:0% -32768:0% -66000:0%
RX states:410 probes:213 naks:0 defs:0 dups:0
TX states:410 probes:197 naks:0 acks:0 dups:0
Congestion bearer:0 link:0 Send queue max:1 avg:0
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There used to be a time when TIPC had lots of Kconfig knobs the
end user could alter, but they have all been made automatic or
obsolete, with the exception of CONFIG_TIPC_PORTS. This
previously existing set of options was all hidden under the
TIPC_ADVANCED setting, which does not exist in any code, but
only in Kconfig scope.
Having this now, just to hide the one remaining "advanced"
option no longer makes sense. Remove it. Also get rid of the
ifdeffery in the TIPC code that allowed for TIPC_PORTS to be
possibly undefined.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Gets rid of the need for users to specify the maximum number of
name publications supported by TIPC. TIPC now automatically provides
support for the maximum number of name publications to 65535.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gets rid of the need for users to specify the maximum number of
name subscriptions supported by TIPC. TIPC now automatically provides
support for the maximum number of name subscriptions to 65535.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added to the following:
- tipc_random
- tipc_own_addr
- tipc_max_ports
- tipc_net_id
- tipc_remote_management
- handler_enabled
The above global variables are read often, but written rarely. Use
__read_mostly to prevent them being on the same cacheline as another
variable which is written to often, which would cause cacheline
bouncing.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since now tipc_net_start() always returns a success code - 0, its
return value type should be changed from integer to void, which can
avoid unnecessary check for its return value.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no real reason to check whether all letters in the given
media name and network interface name are within the character set
defined in tipc_alphabet array. Even if we eliminate the checking,
the rest of checking conditions in tipc_enable_bearer() can ensure
we do not enable an invalid or illegal bearer.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal log buffer handling functions can now safely be
removed since there is no code using it anymore. Requests to
interact with the internal tipc log buffer over netlink (in
config.c) will report 'obsolete command'.
This represents the final removal of any references to a
struct print_buf, and the removal of the struct itself.
We also get rid of a TIPC specific Kconfig in the process.
Finally, log.h is removed since it is not needed anymore.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
All messages should go directly to the kernel log. The TIPC
specific error, warning, info and debug trace macro's are
removed and all references replaced with pr_err, pr_warn,
pr_info and pr_debug.
Commonly used sub-strings are explicitly declared as a const
char to reduce .text size.
Note that this means the debug messages (changed to pr_debug),
are now enabled through dynamic debugging, instead of a TIPC
specific Kconfig option (TIPC_DEBUG). The latter will be
phased out completely
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
[PG: use pr_fmt as suggested by Joe Perches <joe@perches.com>]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Some of the comment blocks are floating in limbo between two
functions, or between blocks of code. Delete the extra line
feeds between any comment and its associated following block
of code, to be consistent with the majority of the rest of
the kernel. Also delete trailing newlines at EOF and fix
a couple trivial typos in existing comments.
This is a 100% cosmetic change with no runtime impact. We get
rid of over 500 lines of non-code, and being blank line deletes,
they won't even show up as noise in git blame.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Initialization now occurs in the calling thread of control,
rather than being deferred to the TIPC tasklet. With the
current codebase, the deferral is no longer necessary.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Initialization now occurs in the calling thread of control,
rather than being deferred to the TIPC tasklet. With the
current codebase, the deferral is no longer necessary.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Removes all references to the global variable that records whether
TIPC is running in "single node" mode or "network" mode, since this
information can be easily deduced from the global variable that
records TIPC's network address. (i.e. a non-zero network address
means that TIPC is running in network mode.)
The changes made update most existing mode-based checks to use the
network address global variable. A few checks that are no longer
needed are removed entirely, along with any associated code lying on
non-executable control paths.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Removes all references to TIPC's "not running" mode, since the
removal of support for the native API means that there is no longer
any way to interact with TIPC if it has not been initialized.
The changes made consist of removing mode-based checks that are no
longer needed, along with any associated code lying on non-executable
control paths.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Change TIPC's shutdown code to deactivate generic networking support
before terminating Ethernet media support. The deactivation of generic
networking support causes all existing bearers to be destroyed, meaning
the Ethernet media termination routine no longer has to bother marking
them as unavailable.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
With calls to modular infrastructure, these files really
needs the full module.h header. Call it out so some of the
cleanups of implicit and unrequired includes elsewhere can be
cleaned up.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The kernel already prints its build timestamp during boot, no need to
repeat it in random drivers and produce different object files each
time.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: netdev@vger.kernel.org
Cc: tipc-discussion@lists.sourceforge.net
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Gets rid of the need for users to specify the maximum number of
cluster nodes supported by TIPC. TIPC now automatically provides
support for all 4K nodes allowed by its addressing scheme.
Note: This change sets TIPC's memory usage to the amount used by
a maximum size node table with 4K entries. An upcoming patch that
converts the node table from a linear array to a hash table will
compact the node table to a more efficient design, but for clarity
it is nice to have all the Kconfig infrastruture go away separately.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Jon Paul Maloy
Erik Hugne
Ying Xue
Richard Alpe
David S. Miller
Patrick McHardy
Paul Gortmaker
Erik Hugne
Allan Stephens
Michal Marek