Граф коммитов

3 Коммитов

Автор SHA1 Сообщение Дата
Samuel Mendoza-Jonas 8d951a75d0 net/ncsi: Configure multi-package, multi-channel modes with failover
This patch extends the ncsi-netlink interface with two new commands and
three new attributes to configure multiple packages and/or channels at
once, and configure specific failover modes.

NCSI_CMD_SET_PACKAGE mask and NCSI_CMD_SET_CHANNEL_MASK set a whitelist
of packages or channels allowed to be configured with the
NCSI_ATTR_PACKAGE_MASK and NCSI_ATTR_CHANNEL_MASK attributes
respectively. If one of these whitelists is set only packages or
channels matching the whitelist are considered for the channel queue in
ncsi_choose_active_channel().

These commands may also use the NCSI_ATTR_MULTI_FLAG to signal that
multiple packages or channels may be configured simultaneously. NCSI
hardware arbitration (HWA) must be available in order to enable
multi-package mode. Multi-channel mode is always available.

If the NCSI_ATTR_CHANNEL_ID attribute is present in the
NCSI_CMD_SET_CHANNEL_MASK command the it sets the preferred channel as
with the NCSI_CMD_SET_INTERFACE command. The combination of preferred
channel and channel whitelist defines a primary channel and the allowed
failover channels.
If the NCSI_ATTR_MULTI_FLAG attribute is also present then the preferred
channel is configured for Tx/Rx and the other channels are enabled only
for Rx.

Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17 21:09:49 -08:00
Justin.Lee1@Dell.com 9771b8ccdf net/ncsi: Extend NC-SI Netlink interface to allow user space to send NC-SI command
The new command (NCSI_CMD_SEND_CMD) is added to allow user space application
to send NC-SI command to the network card.
Also, add a new attribute (NCSI_ATTR_DATA) for transferring request and response.

The work flow is as below.

Request:
User space application
	-> Netlink interface (msg)
	-> new Netlink handler - ncsi_send_cmd_nl()
	-> ncsi_xmit_cmd()

Response:
Response received - ncsi_rcv_rsp()
	-> internal response handler - ncsi_rsp_handler_xxx()
	-> ncsi_rsp_handler_netlink()
	-> ncsi_send_netlink_rsp ()
	-> Netlink interface (msg)
	-> user space application

Command timeout - ncsi_request_timeout()
	-> ncsi_send_netlink_timeout ()
	-> Netlink interface (msg with zero data length)
	-> user space application

Error:
Error detected
	-> ncsi_send_netlink_err ()
	-> Netlink interface (err msg)
	-> user space application

Signed-off-by: Justin Lee <justin.lee1@dell.com>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-15 22:00:59 -07:00
Samuel Mendoza-Jonas 955dc68cb9 net/ncsi: Add generic netlink family
Add a generic netlink family for NCSI. This supports three commands;
NCSI_CMD_PKG_INFO which returns information on packages and their
associated channels, NCSI_CMD_SET_INTERFACE which allows a specific
package or package/channel combination to be set as the preferred
choice, and NCSI_CMD_CLEAR_INTERFACE which clears any preferred setting.

Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-05 10:43:37 -05:00