[ Upstream commit 0d10e90cee ]
A DEVAPC violation occurs when removing the module
due to accessing HW registers without base clock.
To fix this bug, the correct method is:
1. Call the runtime resume function to enable the
clock;
2. Operate the registers to reset the HW;
3. Turn off the clocks and disable the device
RPM mechanism.
Signed-off-by: Zhichao Liu <zhichao.liu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221110072839.30961-1-zhichao.liu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db2d2dc9a0 ]
In case the requested bus clock is higher than the input clock, the correct
dividers (pre = 0, post = 0) are returned from mx51_ecspi_clkdiv(), but
*fres is left uninitialized and therefore contains an arbitrary value.
This causes trouble for the recently introduced PIO polling feature as the
value in spi_imx->spi_bus_clk is used there to calculate for which
transfers to enable PIO polling.
Fix this by setting *fres even if no clock dividers are in use.
This issue was observed on Kontron BL i.MX8MM with an SPI peripheral clock set
to 50 MHz by default and a requested SPI bus clock of 80 MHz for the SPI NOR
flash.
With the fix applied the debug message from mx51_ecspi_clkdiv() now prints the
following:
spi_imx 30820000.spi: mx51_ecspi_clkdiv: fin: 50000000, fspi: 50000000,
post: 0, pre: 0
Fixes: 6fd8b8503a ("spi: spi-imx: Fix out-of-order CS/SCLK operation at low speeds")
Fixes: 07e7593877 ("spi: spi-imx: add PIO polling support")
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: David Jander <david@protonic.nl>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20221115181002.2068270-1-frieder@fris.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 804313b64e ]
pci_get_device() will increase the reference count for the returned
pci_dev. Since 'dma_dev' is only used to filter the channel in
dw_spi_dma_chan_filer() after using it we need to call pci_dev_put() to
decrease the reference count. Also add pci_dev_put() for the error case.
Fixes: 7063c0d942 ("spi/dw_spi: add DMA support")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20221116093204.46700-1-wangxiongfeng2@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62aa1a344b ]
When this driver is used with a driver that uses preallocated spi_transfer
structs. The speed_hz is halved by every run. This results in:
spi_stm32 44004000.spi: SPI transfer setup failed
ads7846 spi0.0: SPI transfer failed: -22
Example when running with DIV_ROUND_UP():
- First run; speed_hz = 1000000, spi->clk_rate 125000000
div 125 -> mbrdiv = 7, cur_speed = 976562
- Second run; speed_hz = 976562
div 128,00007 (roundup to 129) -> mbrdiv = 8, cur_speed = 488281
- Third run; speed_hz = 488281
div 256,000131072067109 (roundup to 257) and then -EINVAL is returned.
Use DIV_ROUND_CLOSEST to allow to round down and allow us to keep the
set speed.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20221103080043.3033414-1-sean@geanix.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 195583504b ]
The original fix "spi: stm32: Rate-limit the 'Communication suspended' message"
still leads to "stm32h7_spi_irq_thread: 1696 callbacks suppressed" spew in the
kernel log. Since this 'Communication suspended' message is a debug print, add
RATELIMIT_MSG_ON_RELEASE flag to inhibit the "callbacks suspended" part during
normal operation and only print summary at the end.
Fixes: ea8be08cc9 ("spi: stm32: Rate-limit the 'Communication suspended' message")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20221018183513.206706-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e9204cddc ]
SPI code checks for non-zero sgt->orig_nents to determine if the buffer
has been DMA-mapped. Ensure that sg_table is really zeroed after free to
avoid potential NULL pointer dereference if the given SPI xfer object is
reused again without being DMA-mapped.
Fixes: 0c17ba73c0 ("spi: Fix cache corruption due to DMA/PIO overlap")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20220930113408.19720-1-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1224e29572 ]
The COUNT_VALUE in the PACKET_CNT register is 16-bit so the maximum
value is 65535. Asking the driver to transfer a larger size currently
leads to the DMA transfer timing out. Implement ->max_transfer_size()
and have the core split the transfer as needed.
Fixes: 230d42d422 ("spi: Add s3c64xx SPI Controller driver")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220927112117.77599-5-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29f65f2171 ]
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
Fixes:db91841b58f9a ("spi/omap100k: Convert to runtime PM")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20220924121310.78331-4-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 618d815fc9 ]
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
Fixes:abf00907538e2 ("spi: dw: Add Baikal-T1 SPI Controller glue driver")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20220924121310.78331-3-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36acf80fc0 ]
Since [1], controller's busy flag isn't set anymore when the
__spi_transfer_message_noqueue() is used instead of the
__spi_pump_transfer_message() logic for spi_sync transfers.
Since the pow2 clock ops were limited to only be available when a
transfer is ongoing (between prepare_transfer_hardware and
unprepare_transfer_hardware callbacks), the only way to track this
down is to check for the controller cur_msg.
[1] ae7d2346dc ("spi: Don't use the message queue if possible in spi_sync")
Fixes: 09992025da ("spi: meson-spicc: add local pow2 clock ops to preserve rate between messages")
Fixes: ae7d2346dc ("spi: Don't use the message queue if possible in spi_sync")
Reported-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/r/20220908121803.919943-1-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 494a22765c ]
Add the missing clk_disable_unprepare() before return
from spi_qup_pm_resume_runtime() in the error handling case.
Fixes: dae1a7700b (“spi: qup: Handle clocks in pm_runtime suspend and resume”)
Signed-off-by: Xu Qiang <xuqiang36@huawei.com>
Link: https://lore.kernel.org/r/20220825065324.68446-2-xuqiang36@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b2bf6b7fa ]
'status' is known to be 0 at this point. The expected error code is
PTR_ERR(clk).
Switch to dev_err_probe() in order to display the expected error code (in a
human readable way).
This also filters -EPROBE_DEFER cases, should it happen.
Fixes: 1ab7f2a435 ("staging: mt7621-spi: add mt7621 support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/928f3fb507d53ba0774df27cea0bbba4b055993b.1661599671.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 09992025da upstream.
At the end of a message, the HW gets a reset in meson_spicc_unprepare_transfer(),
this resets the SPICC_CONREG register and notably the value set by the
Common Clock Framework.
This is problematic because:
- the register value CCF can be different from the corresponding CCF cached rate
- CCF is allowed to change the clock rate whenever the HW state
This introduces:
- local pow2 clock ops checking the HW state before allowing a clock operation
- separation of legacy pow2 clock patch and new enhanced clock path
- SPICC_CONREG datarate value is now value kepts across messages
It has been checked that:
- SPICC_CONREG datarate value is kept across messages
- CCF is only allowed to change the SPICC_CONREG datarate value when busy
- SPICC_CONREG datarate value is correct for each transfer
This didn't appear before commit 3e0cf4d3fc ("spi: meson-spicc: add a linear clock divider support")
because we recalculated and wrote the rate for each xfer.
Fixes: 3e0cf4d3fc ("spi: meson-spicc: add a linear clock divider support")
Reported-by: Da Xue <da@libre.computer>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220811134445.678446-1-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7e9984d183 ]
After calling spi_unregister_master(), the refcount of master will
be decrease to 0, and it will be freed in spi_controller_release(),
the device data also will be freed, so it will lead a UAF when using
'tspi'. To fix this, get the master before unregister and put it when
finish using it.
Fixes: 26c8634182 ("spi: tegra20-slink: Don't use resource-managed spi_register helper")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220713094024.1508869-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43cc5a0afe ]
This reverts commit 59ebbe40fb ("spi: simplify
devm_spi_register_controller").
If devm_add_action() fails in devm_add_action_or_reset(),
devm_spi_unregister() will be called, it decreases the
refcount of 'ctlr->dev' to 0, then it will cause uaf in
the drivers that calling spi_put_controller() in error path.
Fixes: 59ebbe40fb ("spi: simplify devm_spi_register_controller")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220712135504.1055688-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e3ca32f46 ]
The spi_alloc_master() call is not undone in all error handling paths.
Moreover, there is no .remove function to release the allocated memory.
In order to fix both this issues, switch to devm_spi_alloc_master().
This allows further simplification of the probe.
Fixes: ba2fc167e9 ("spi: altera: Add DFL bus driver for Altera API Controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/0607bb59f4073f86abe5c585d35245aef0b045c6.1653805901.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b620aa3a7b ]
RSPI IP on RZ/{A, G2L} SoC's has the same signal for both interrupt
and DMA transfer request. Setting DMARS register for DMA transfer
makes the signal to work as a DMA transfer request signal and
subsequent interrupt requests to the interrupt controller
are masked.
PIO fallback does not work as interrupt signal is disabled.
This patch fixes this issue by re-enabling the interrupts by
calling dmaengine_synchronize().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220721143449.879257-1-biju.das.jz@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4ceaa68445 upstream.
In case a IRQ based transfer times out the bcm2835_spi_handle_err()
function is called. Since commit 1513ceee70 ("spi: bcm2835: Drop
dma_pending flag") the TX and RX DMA transfers are unconditionally
canceled, leading to NULL pointer derefs if ctlr->dma_tx or
ctlr->dma_rx are not set.
Fix the NULL pointer deref by checking that ctlr->dma_tx and
ctlr->dma_rx are valid pointers before accessing them.
Fixes: 1513ceee70 ("spi: bcm2835: Drop dma_pending flag")
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220719072234.2782764-1-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6ece49c569 ]
Enabling the SPI CS35L41 audio codec driver for Steam Deck [1]
revealed a problem with the current AMD SPI controller driver
implementation, consisting of an unrecoverable system hang.
The issue can be prevented if we ensure the max transfer size
and the max message size do not exceed the FIFO buffer size.
According to the implementation of the downstream driver, the
AMD SPI controller is not able to handle more than 70 bytes per
transfer, which corresponds to the size of the FIFO buffer.
Hence, let's fix this by setting the SPI limits mentioned above.
[1] https://lore.kernel.org/r/20220621213819.262537-1-cristian.ciocaltea@collabora.com
Reported-by: Anastasios Vacharakis <vacharakis@o2mail.de>
Fixes: bbb336f39e ("spi: spi-amd: Add AMD SPI controller driver support")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20220706100626.1234731-2-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2b331ac11 ]
It will cause null-ptr-deref if platform_get_resource_byname() returns NULL,
we need check the return value.
Fixes: 858e26a515 ("spi: spi-fsl-qspi: Reduce devm_ioremap size to 4 times AHB buffer size")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220505093954.1285615-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f724c296f2 ]
The Cadence QSPI compatible string required for the SoCFPGA platform
changed from the default "cdns,qspi-nor" to "intel,socfpga-qspi" with
the introduction of an additional quirk in
commit 98d948eb83 ("spi: cadence-quadspi: fix write completion support").
However, that change did not preserve the previously used
quirk for this platform. Reinstate the `CQSPI_DISABLE_DAC_MODE` quirk
for the SoCFPGA platform.
Fixes: 98d948eb83 ("spi: cadence-quadspi: fix write completion support")
Cc: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20220427153446.10113-1-abbotti@mev.co.uk
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5d933f09a ]
The hardware (except for the ROCKCHIP_SPI_VER2_TYPE2 version) does not
support active-high native chip selects. However if such a CS is configured
the core does not error as it normally should, because the
'ctlr->use_gpio_descriptors = true' line in rockchip_spi_probe() makes the
core set SPI_CS_HIGH in ctlr->mode_bits.
In such a case the spi-rockchip driver operates normally but produces an
active-low chip select signal without notice.
There is no provision in the current core code to handle this
situation. Fix by adding a check in the ctlr->setup function (similarly to
what spi-atmel.c does).
This cannot be done reading the SPI_CS_HIGH but in ctlr->mode_bits because
that bit gets always set by the core for master mode (see above).
Fixes: eb1262e3cc ("spi: spi-rockchip: use num-cs property and ctlr->enable_gpiods")
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://lore.kernel.org/r/20220421213251.1077899-1-luca.ceresoli@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a4bf922d4 ]
After power up, the cs and clock is in default status, and the cs-high
and clock polarity dts property configuration will take no effect until
the calling of rockchip_spi_config in the first transmission.
So preset them to make sure a correct voltage before the first
transmission coming.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20220216014028.8123-5-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 869f2c94db ]
The spi which's version is higher than ver 2 will automatically
enable this feature.
If the length of master transmission is uncertain, the RK spi slave
is better to automatically stop after cs inactive instead of waiting
for xfer_completion forever.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20220216014028.8123-4-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc470d5534 ]
If the device is already in a runtime PM enabled state
pm_runtime_get_sync() will return 1, so a test for negative
value should be used to check for errors.
Fixes: deba25800a ("spi: Add driver for IMG SPFI controller")
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20220422062641.10486-1-zhengyongjun3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b1ea69a63 ]
wait_for_completion_timeout() returns unsigned long not int.
It returns 0 if timed out, and positive if completed.
The check for <= 0 is ambiguous and should be == 0 here
indicating timeout which is the only error case.
Fixes: 5720ec0a6d ("spi: spi-ti-qspi: Add DMA support for QSPI mmap read")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220411111034.24447-1-linmq006@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f381481a5 ]
The direction field in the DMA config is deprecated. The rspi driver
sets {src,dst}_{addr,addr_width} based on the DMA direction and
it results in dmaengine_slave_config() failure as RZ DMAC driver
validates {src,dst}_addr_width values independent of DMA direction.
This patch fixes the issue by passing both {src,dst}_{addr,addr_width}
values independent of DMA direction.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220411173115.6619-1-biju.das.jz@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 98d948eb83 upstream.
Some versions of the Cadence QSPI controller does not have the write
completion register implemented(CQSPI_REG_WR_COMPLETION_CTRL). On the
Intel SoCFPGA platform the CQSPI_REG_WR_COMPLETION_CTRL register is
not configured.
Add a quirk to not write to the CQSPI_REG_WR_COMPLETION_CTRL register.
Fixes: 9cb2ff1117 ("spi: cadence-quadspi: Disable Auto-HW polling)
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211108200854.3616121-1-dinguyen@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
[IA: backported for linux=5.15.y]
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c235cc250 upstream.
Use the spi_mem_default_supports_op() core helper in order to take into
account the buswidth specified by the user in device tree.
Cc: <stable@vger.kernel.org>
Fixes: 0e6aae08e9 ("spi: Add QuadSPI driver for Atmel SAMA5D2")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220406133604.455356-1-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f1d388f216 ]
Since the conversion to spi-mem, the driver advertised support for
various operations that cqspi_set_protocol() was never expected to handle
correctly - in particuar all non-DTR operations with command or address
buswidth > 1. For DTR, all operations except for 8-8-8 would fail, as
cqspi_set_protocol() returns -EINVAL.
In non-DTR mode, this resulted in data corruption for SPI-NOR flashes that
support such operations. As a minimal fix that can be backported to stable
kernels, simply disallow the unsupported operations again to avoid this
issue.
Fixes: a314f63677 ("mtd: spi-nor: Convert cadence-quadspi to use spi-mem framework")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220406132832.199777-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 317c204561 ]
After system resumes, the registers of nor controller are
initialized with default values. The nor controller will
not function properly.
To handle both issues above, we add mtk_nor_init() in
mtk_nor_resume after pm_runtime_force_resume().
Fixes: 3bfd9103c7 ("spi: spi-mtk-nor: Add power management support")
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Link: https://lore.kernel.org/r/20220412115743.22641-1-allen-kh.cheng@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97e4827d77 ]
cqspi_set_protocol() only set the data width, but ignored the command
and address width (except for 8-8-8 DTR ops), leading to corruption of
all transfers using 1-X-X or X-X-X ops. Fix by setting the other two
widths as well.
While we're at it, simplify the code a bit by replacing the
CQSPI_INST_TYPE_* constants with ilog2().
Tested on a TI AM64x with a Macronix MX25U51245G QSPI flash with 1-4-4
read and write operations.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220331110819.133392-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c7d1b2812 ]
This fixes case where MSPI controller is used to access spi-nor
flash and BSPI block is not present.
Fixes: 5f195ee7d8 ("spi: bcm-qspi: Implement the spi_mem interface")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220328142442.7553-1-kdasu.kdev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 03b1be379d upstream.
this patch support tick_delay bit[31:30] without enhance_timing feature.
Fixes: f84d866ab43f("spi: mediatek: add tick_delay support")
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220315032411.2826-2-leilk.liu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c9839acfcb ]
Use of_device_get_match_data() to simplify the code.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220315023138.2118293-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13262fc26c ]
As the potential failure of the dma_set_mask(),
it should be better to check it and return error
if fails.
Fixes: 126bdb606f ("spi: spi-zynqmp-gqspi: return -ENOMEM if dma_map_single fails")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220302092051.121343-1-jiasheng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 609d7ffdc4 ]
The pci_get_slot() increases its reference count, the caller
must decrement the reference count by calling pci_dev_put().
Fixes: 743485ea3b ("spi: pxa2xx-pci: Do a specific setup in a separate function")
Fixes: 2501452160 ("spi: pxa2xx-pci: Enable DMA for Intel Merrifield")
Reported-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220223191637.31147-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47c3e06ed9 ]
This func misses checking for platform_get_irq()'s call and may passes the
negative error codes to request_threaded_irq(), which takes unsigned IRQ #,
causing it to fail with -EINVAL, overriding an original error code.
Stop calling request_threaded_irq() with invalid IRQ #s.
Fixes: 921fc1838f ("spi: tegra210-quad: Add support for Tegra210 QSPI controller")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220128165956.27821-1-linmq006@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f92724d4b ]
This func misses checking for platform_get_irq()'s call and may passes the
negative error codes to request_threaded_irq(), which takes unsigned IRQ #,
causing it to fail with -EINVAL, overriding an original error code.
Stop calling request_threaded_irq() with invalid IRQ #s.
Fixes: f333a331ad ("spi/tegra114: add spi driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220128165238.25615-1-linmq006@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5fd6739e0d upstream.
By working with external hardware ECC engines, we figured out that
Under certain circumstances, it is needed for the SPI controller to
check INT_TX_EMPTY and INT_RX_NOT_EMPTY in both receive and transmit
path (not only in the receive path). The delay penalty being
negligible, move this code in the common path.
Fixes: b942d80b0a ("spi: Add MXIC controller driver")
Cc: stable@vger.kernel.org
Suggested-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Zhengxun Li <zhengxunli@mxic.com.tw>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-10-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ebc4cb43ea ]
While computing sgs in spi_map_buf(), the data type
used in min_t() for max_seg_size is 'unsigned int' where
as that of ctlr->max_dma_len is 'size_t'.
min_t(unsigned int,x,y) gives wrong results if one of x/y is
'size_t'
Consider the below examples on a 64-bit machine (ie size_t is
64-bits, and unsigned int is 32-bit).
case 1) min_t(unsigned int, 5, 0x100000001);
case 2) min_t(size_t, 5, 0x100000001);
Case 1 returns '1', where as case 2 returns '5'. As you can see
the result from case 1 is wrong.
This patch fixes the above issue by using the data type of the
parameters that are used in min_t with maximum data length.
Fixes: commit 1a4e53d2fc ("spi: Fix invalid sgs value")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220316175317.465-1-biju.das.jz@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a4e53d2fc ]
max_seg_size is unsigned int and it can have a value up to 2^32
(for eg:-RZ_DMAC driver sets dma_set_max_seg_size as U32_MAX)
When this value is used in min_t() as an integer type, it becomes
-1 and the value of sgs becomes 0.
Fix this issue by replacing the 'int' data type with 'unsigned int'
in min_t().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220307184843.9994-1-biju.das.jz@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80808768e4 ]
After slave abort, all DMA should be stopped, or it will affect the
next transmission and maybe abort again.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20220216014028.8123-3-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab3824427b ]
In zynq_qspi_exec_mem_op(), kzalloc() is directly used in memset(),
which could lead to a NULL pointer dereference on failure of
kzalloc().
Fix this bug by adding a check of tmpbuf.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_SPI_ZYNQ_QSPI=m show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 67dca5e580 ("spi: spi-mem: Add support for Zynq QSPI controller")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Link: https://lore.kernel.org/r/20211130172253.203700-1-zhou1615@umn.edu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 37c2c83ca4 upstream.
The issue happens in several error paths in uniphier_spi_probe().
When either dma_get_slave_caps() or devm_spi_register_master() returns
an error code, the function forgets to decrease the refcount of both
`dma_rx` and `dma_tx` objects, which may lead to refcount leaks.
Fix it by decrementing the reference count of specific objects in
those error paths.
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Fixes: 28d1dddc59 ("spi: uniphier: Add DMA transfer mode support")
Link: https://lore.kernel.org/r/20220125101214.35677-1-xiongx18@fudan.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zhichao Liu
Frieder Schrempf
Xiongfeng Wang
Sean Nyekjaer
Marek Vasut
Marek Szyprowski
Vincent Whitchurch
Zhang Qilong
Neil Armstrong
Xu Qiang
Christophe JAILLET
Yang Yingliang
Biju Das
Guo Mengqi
Marc Kleine-Budde
Cristian Ciocaltea
Ian Abbott
Luca Ceresoli
Jon Lin
Zheng Yongjun
Miaoqian Lin
Patrice Chotard
Dinh Nguyen
Tudor Ambarus
Matthias Schiffer
Allen-KH Cheng
Vinod Koul
Kamal Dasu
Leilk Liu
Minghao Chi
Jiasheng Jiang
Andy Shevchenko
Miquel Raynal
Zhou Qingyang
Xin Xiong